cutting software installation - uscutter support · step 14: select the cutter and output device...
TRANSCRIPT
![Page 1: CUTTING SOFTWARE INSTALLATION - USCutter Support · STEP 14: Select the Cutter and Output Device matching the settings from the example below. STEP 15: To cut press the Cutter and](https://reader036.vdocuments.us/reader036/viewer/2022081601/60f88c795a4f567ab0756005/html5/thumbnails/1.jpg)
CUTTING SOFTWARE INSTALLATION
STEP 1: Insert the SignBlazer Elements disc into your computer. The disc is located in the accessoriesbox (small cardboard box).
IMPORTANT: If this disc is missing, SignBlazer Elements is available for download.
* * * * DOWNLOAD REQUIRED SOFTWARE * * * *
* * * * * * * * * * * * * * * * * * * * * * * * * * *STEP 2: Select Run Setup.
![Page 2: CUTTING SOFTWARE INSTALLATION - USCutter Support · STEP 14: Select the Cutter and Output Device matching the settings from the example below. STEP 15: To cut press the Cutter and](https://reader036.vdocuments.us/reader036/viewer/2022081601/60f88c795a4f567ab0756005/html5/thumbnails/2.jpg)
STEP 3: The Welcome to the SignBlazer setup screen will display, press Next.
STEP 4: Select Yes and press Next.
![Page 3: CUTTING SOFTWARE INSTALLATION - USCutter Support · STEP 14: Select the Cutter and Output Device matching the settings from the example below. STEP 15: To cut press the Cutter and](https://reader036.vdocuments.us/reader036/viewer/2022081601/60f88c795a4f567ab0756005/html5/thumbnails/3.jpg)
STEP 5: Select I accept the agreement and press Next (x6).
![Page 4: CUTTING SOFTWARE INSTALLATION - USCutter Support · STEP 14: Select the Cutter and Output Device matching the settings from the example below. STEP 15: To cut press the Cutter and](https://reader036.vdocuments.us/reader036/viewer/2022081601/60f88c795a4f567ab0756005/html5/thumbnails/4.jpg)
![Page 5: CUTTING SOFTWARE INSTALLATION - USCutter Support · STEP 14: Select the Cutter and Output Device matching the settings from the example below. STEP 15: To cut press the Cutter and](https://reader036.vdocuments.us/reader036/viewer/2022081601/60f88c795a4f567ab0756005/html5/thumbnails/5.jpg)
![Page 6: CUTTING SOFTWARE INSTALLATION - USCutter Support · STEP 14: Select the Cutter and Output Device matching the settings from the example below. STEP 15: To cut press the Cutter and](https://reader036.vdocuments.us/reader036/viewer/2022081601/60f88c795a4f567ab0756005/html5/thumbnails/6.jpg)
STEP 6: Select your cutter from the list. If your cutter is not listed, select the Copam CP-2500 andpress Next.
STEP 7: Select the COM? (if known) and press Next. If the cutter’s COM number is unknown selectCOM1.
![Page 7: CUTTING SOFTWARE INSTALLATION - USCutter Support · STEP 14: Select the Cutter and Output Device matching the settings from the example below. STEP 15: To cut press the Cutter and](https://reader036.vdocuments.us/reader036/viewer/2022081601/60f88c795a4f567ab0756005/html5/thumbnails/7.jpg)
STEP 8: Leave Baud Rate as 9600 and press Next.
STEP 9: Leave all this settings as shown and press Next.
![Page 8: CUTTING SOFTWARE INSTALLATION - USCutter Support · STEP 14: Select the Cutter and Output Device matching the settings from the example below. STEP 15: To cut press the Cutter and](https://reader036.vdocuments.us/reader036/viewer/2022081601/60f88c795a4f567ab0756005/html5/thumbnails/8.jpg)
STEP 10: Press Install.
NOTE: Installing...
![Page 9: CUTTING SOFTWARE INSTALLATION - USCutter Support · STEP 14: Select the Cutter and Output Device matching the settings from the example below. STEP 15: To cut press the Cutter and](https://reader036.vdocuments.us/reader036/viewer/2022081601/60f88c795a4f567ab0756005/html5/thumbnails/9.jpg)
STEP 11: Press Finish.
STEP 12: Open SignBlazer Elements, and press the Trial Mode button.
![Page 10: CUTTING SOFTWARE INSTALLATION - USCutter Support · STEP 14: Select the Cutter and Output Device matching the settings from the example below. STEP 15: To cut press the Cutter and](https://reader036.vdocuments.us/reader036/viewer/2022081601/60f88c795a4f567ab0756005/html5/thumbnails/10.jpg)
CUTTER SETUP
STEP 13: Press the Cutter and Setup buttons.
STEP 14: Select the Cutter and Output Device matching the settings from the example below.
STEP 15: To cut press the Cutter and CUT! buttons, a window will open on the right side and press theCut Tile button.
STEP 16: If you need more information about SignBlazer, download the User's Manual.
Enjoy your new vinyl cutter! Thank you forchoosing USCutter