cts/titan injection bore system - con-tech · pdf filects/titaninjection bore system tie back...

CTS/TITAN Injection Bore System

Tie Back Anchors

Soil Nails &

Micropiles

G IBO®: Injection BOring

G Dynamic pressure grouted,

casing free single step

installation

G Suits all ground conditions

G Rapid, effective ground

and structural stabilisation

November 2006CON-TECH SYSTEMS LTD HQ: 8150 RIVER ROAD • DELTA BC, V4G 1B5 • CANADA • PH: (604) 946-5571 • FAX: (604) 946-5548

WESTERN DIVISION: DELTA, BC, PH: (604) 946-5571, FAX: (604) 946-5548 • DESCANSO CA, USA, PH: (619) 659-9931

FAX: (619)659-9932, E-MAIL: [email protected]

EASTERN DIVISION: • ELIZABETHTOWN ON • CANADA • PH: (613) 342-0041, FAX: (613) 342-0609 • RICHEY FL, USA,

PH: (866) 848 6800 • CHARLOTTE NC, USA, (704) 494-3989 • E-MAIL: [email protected]

CTSCON-TECH SYSTEMS LTD

HQ & WESTERN DIVISION (604) 946-5571

EASTERN DIVISION (613) 342-0041

Email: [email protected] • Website: www.contechsystems.com

2

1 Technical Data 3

2 Drill Bit Selection Chart 5

3 R32/20 7

4 TITAN 30/11, TITAN 30/14 & TITAN 30/16 9

5 TITAN 40/16 & TITAN40/20 13

6 TITAN 52/26 17

7 TITAN 73/56, TITAN 73/53TITAN 73/45 & TITAN 73/35 19

8 TITAN 103/78 & TITAN103/51 21

9 TITAN 130/60 23

Disclaimer:

All products are subject to change at any time without notice. Con-Tech Systems will make the best effort to keep

you informed about any changes. Please check our website (www.contechsystems.com) for updates.

All photos are for illustrative purpose only; weights are approximate.

Products must be used in conformity with safe practices and applicable codes.

For best performance results, refere to CTS/TITAN/IBO installation procedures

Parts-List Index

CON-TECH SYSTEMS LTDHQ & WESTERN DIVISION (604) 946-5571



CTS/TITAN Technical Data

3

CTS

Rod

Siz

eW

eigh

tD

Ø /

INN

ER

ØU

ltim

ate

Yie

ldM

ax. T

est

Des

ign1

Des

ign2

Effe

ctiv

eN

omin

alG

.U.T

.S.

Tem

p. A

nch.

60%

G.U

.T.S

.d

ØD

Øm

min

2ki

pski

pski

pski

pski

psin

inlb

s./lf

.m

m2

kNkN

kNkN

kNm

mm

mkg

/m30

/16

0.59

49.5

40.5

39.6

34.6

29.7

1.02

1.18

1.8

L.H

. TH

RE

AD

382

220

180

176

154

132

2630

2.7

30/1

40.

6158

.549

.546

.840

.935

.11.

031.

181.

9L.

H. T

HR

EA

D39

526

022

020

8.0

182

156

2630

2.9

32/2

00.

6065

.454

.952

.345

.839

.31.

101.

262.

2L.

H. T

HR

EA

D38

929

124

423

320

417

528

323.

230

/11

0.69

72.0

58.5

5850

.443

.21.

031.

182.

2L.

H. T

HR

EA

D44

632

026

025

622

419

226

303.

340

/20

1.13

121.

296

.795

.684

.872

.71.

421.

573.

8L.

H. T

HR

EA

D72

653

943

042

537

732

336

405.

640

/16

1.36

148.

411

8.1

116.

910

3.9

89.0

1.42

1.57

4.7

L.H

. TH

RE

AD

879

660

525

520

462

396

3640

7.0

52/2

62.

0720

8.9

164.

216

0.1

146.

212

5.3

1.92

2.05

6.7

L.H

. TH

RE

AD

1337

929

730

712

650

557

4952

10.0

73/5

62.

1926

8.5

176.

517

4.3

173.

216

1.1

2.76

2.87

7.5

R.H

. TH

RE

AD

1414

1194

785

775

770

716

7073

11.1

73/5

32.

5326

0.9

218.

120

8.7

182.

615

6.5

2.76

2.87

8.3

R.H

. TH

RE

AD

1631

1160

970

928

812

696

7073

12.3

73/4

53.

5036

6.5

265.

326

3.1

256.

621

9.9

2.76

2.87

12.0

R.H

. TH

RE

AD

2260

1630

1180

1170

1141

978

7073

17.8

73/3

54.

2044

5.2

304.

730

2.5

301.

326

7.1

2.76

2.87

14.2

R.H

. TH

RE

AD

2710

1980

1355

1345

1340

1188

7073

21.2

103/

784.

8851

3.2

404.

840

0.3

359.

230

7.9

3.94

4.06

16.7

R.H

. TH

RE

AD

3146

2282

1800

1780

1597

1369

100

103

24.9

103/

518.

5377

8.1

618.

461

6.1

544.

646

6.8

3.94

4.06

29.2

R.H

. TH

RE

AD

5501

3460

2750

2740

2422

2076

100

103

43.4

127/

111*

4.65

539.

740

7.0

404.

837

7.8

323.

83.

944.

0615

.8R

.H. T

HR

EA

D30

0024

0018

1018

0016

8014

4010

010

323

.513

0/60

14.7

917

85.5

1180

.611

73.8

1169

.310

71.3

4.92

5.12

50.4

R.H

. TH

RE

AD

9540

7940

5250

5220

5200

4764

125

130

75.0

1 Tem

pora

ry A

ncho

rs ;

2 Per

man

ent A

ncho

rsIm

peria

l val

ues

conv

erte

d fro

m m

etric

val

ues;

Oct

ober

200

6

Are

aLo

ad C

apac

ityO

utsi

de D

iam

eter

November 2006

TIT

AN

127/1

11:

Allo

wable

ben-

din

g m

om

ent

=

23.9

kN

m

(737.5

lbsft)

Cert

ifie

d t

o

ISO

9001

No

te:

Subje

ct

to

change w

ithout

notice.

Sh

ear

Fo

rce

Allo

wable

shear

forc

e is d

ete

r-

min

ed b

y t

he

form

ula

:

Qa

llow

=Y

ield

*A

1.7

5*√3

A:

(Ste

el) A

rea

November 2006

CTSCON-TECH SYSTEMS LTD

HQ & WESTERN DIVISION (604) 946-5571



CTS/TITAN Technical Data

4

THE TITAN THREAD MEETS AND EXCEEDS ASTM REQUIREMENTS

FOR RE-BAR DEFORMATIONS (ASTM-A-615). GROUT CRACK

WIDTH = O.1mm AT 1.25 OF DESIGN LOAD.

NO ADDITIONAL CORROSION PROTECTION IS REQUIRED

IBO/TITAN BARS ARE ROLLED OUT OF HIGH QUALITY STEEL TUB-

ING FOR SOIL NAILS, ROCK AND SOIL ANCHORS AND MINI /

MICRO PILES.

THEIR UNIQUE INSTALLATION METHOD, I.E. DYNAMIC (TREMI)-

GROUTING DURING DRILLING ASSURES CONTINUOUS GROUT

COVER FOR GOOD CORROSION PROTECTION AND SUPERIOR

SKIN FRICTION AND BOND.

FOR ADDITIONAL CORROSION PROTECTION, BARS AND HARD-

WARE CAN ALSO BE

EPOXY COATED, acc. to ASTM A-934, ASTM A-775 or AASHTO M284

ZINC METALLIZED, acc. to ASTM A-153 or AASHTO M232

HOT DIP GALVANIZED, acc. to ASTM A-153 or AASHTO M232

OR BE SUPPLIED IN (INOX) STAINLESS STEEL.

INSTEAD OF EXTRA CORROSION PROTECTION, THE SACRIFICIAL-

STEEL METHOD, CHOOSING THE BAR LARGER THAN

REQUIRED, CAN BE USED. THIS METHOD IS VERY COMMON IN

EUROPE AND FOR REINFORCED EARTH SYSTEMS.

STOCKED TITAN BARS: 30/16, R32/20, 30/11, 30/14, 40/20, 40/16,

52/26, 73/53, 103/78, 103/51.

NOTES:




Drill Bit Selection Chart

5

CTS

Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical

changes. Weights are approximate.

November 2006

Carb

ide C

ross

Carb

ide C

ross

Cut 3

-ste

pC

ut 3

-ste

p

carb

ide ti

pped

carb

ide ti

pped

ha

rdn

ess H

V 1

80

0 h

ard

ne

ss H

V 1

80

0

(75

mm

Ø)

90

mm

Ø

Button T

ype

Button T

ype

hard

ness H

V 7

00

hard

ness H

V 7

00

42

mm

Ø / 4

6 m

m Ø

/ 5

1 m

m Ø

/ 5

5 m

m Ø

70

mm

Ø

Mic

ro

Pil

es

DIN

41

28

/ S

oil

Na

ils

/ A

nc

ho

rs

DIN

41

25

TITAN

TITAN

TITAN

TITAN

TITAN

TITAN

30/1

1(left)

40/1

6(left)

52/2

673/5

3(r

ight)

1

03/7

8(r

ight)

103/5

1(r

igh

t)

Cro

ss C

ut

Cro

ss C

ut

Cro

ss C

ut

Cro

ss C

ut

Cro

ss C

ut

Cro

ss C

ut

Drill

Bit

Drill

Bit

Drill

Bit

Drill

Bit

Drill

Bit

Drill

Bit

hard

ness H

V 3

75

hard

ness H

V 3

75 h

ard

ness H

V 3

75

hard

ness H

V 3

75

hard

ness H

V 3

75

hard

ness H

V 3

75

90

mm

Ø9

0 m

m Ø

11

5 m

m Ø

13

0 m

m Ø

17

5 m

m Ø

17

5 m

m Ø

11

5 m

m Ø

13

0 m

m Ø

17

5 m

m Ø

for

cla

y, so

ft s

oil

and s

and/g

ravel

< 5

0 S

.P.T

.

Cla

y B

itC

lay B

itC

lay B

itC

lay B

itC

lay B

itC

lay B

it

hard

ness H

V 2

70 h

ard

ness H

V 2

70 h

ard

ness H

V 2

70

hard

ness H

V 2

70

hard

ness H

V 2

70

hard

ness H

V 2

70

75

mm

Ø1

10

mm

Ø1

30

mm

Ø 2

00

mm

Ø 2

80

mm

Ø 2

80

mm

Ø

95

mm

Ø1

50

mm

Ø

for hard

or hig

h q

uarz

ite rock,

rein

forc

ed c

oncre

te B

25 a

t the

begin

nin

g

> 7

0 M

Pa

Button T

ype

Button T

ype

Button T

ype

Button T

ype

Button T

ype

carb

ide ti

pped

carb

ide ti

pped

carb

ide ti

pped

carb

ide ti

pped

carb

ide ti

pped

ha

rdn

ess H

V 1

80

0hard

ness H

V1800

hard

ne

ss H

V 1

80

0h

ard

ne

ss H

V 1

80

0h

ard

ne

ss H

V 1

80

0

90

mm

Ø1

15

mm

Ø1

30

mm

Ø1

75

mm

Ø1

75

mm

Ø

for directional s

tabili

ty o

f

+ 2

% o

f th

e to

tal le

ng

th

TITAN

30/1

1(left)

TITAN

40

/16

(le

ft)

expla

nation to

diffe

rent

- H

ard

ness to M

ohs e

.g.d

iam

ant 10, carb

ide 9

,5, corr

espond to H

V 1

800 (

Hard

ness to V

ickers

),quarz

ite 7

, sla

te 2

,5

decla

rations o

f hard

ness

- H

RC

60 (H

ard

ness to R

ockw

ell

C) corr

espond to H

V 7

00 (H

ard

ness to V

ickers

), H

RC

38 c

orr

espond to H

V 3

75

and rock h

ard

ness:

- 70 M

Pa (soft s

oil

and lo

ose s

and/g

ravel)

- 7

0 ÷

150 M

Pa (fo

r hard

rock, lik

e d

olo

mit, gra

nite, sandsto

ne)

- S

.P.T

. valu

e (S

tandard

Penetr

ation T

est)

for m

ixed s

oil

with o

bsta

cle

s

> 5

0 S

.P.T

.

Carb

ide O

ffset C

ross C

ut

Carb

ide O

ffset C

ross C

ut

hard

ness H

V 1

800

hard

ness H

V 1

800

46

mm

Ø7

0 m

m Ø

AV

8/B

1-6

for w

ea

the

red

so

ft ro

ck

and g

ravel

hard

ness <

70 M

Pa

for h

ard

ro

ck,

gra

nite, d

olo

mite, s

tandsto

ne,

hard

ness 7

0 - 1

50 M

Pa

Page left blank intentionally




CTS/TITAN

6

CTS



November 2006




7

CTS



November 2006

CTS/TITAN R32/20

CTS Injection Bore Hollow Bar System R32/20

TITAN Injection Hollow Bar, 32/20 mm, design load (60% GUTS) 175 kN,

left hand threaded in lengths of 3 m black

part.no. R32-0127 3.20 kg/m pc

Accessories

Spherical Collar Nut

black, part.no. R32-0126 0.35 kg pc. stock

Coupling

black, part.no. R32-0124 0.43 kg pc. stock

CTS Drill Bit - Carbide 2”, (51mm Ø),

carbide tipped, part.no. R32-0117 0.37 kg pc. stock

CTS Drill Bit - Carbide 2.5”, (63.5mm Ø),

carbide tipped, part.no. R32-0119 0.37 kg pc. stock

TITAN Drill Bit - Soil Bit Y-Cut 3”, (76 mm Ø),

part.no. R32-0115 0.69 kg pc. stock

TITAN Drill Bit - Clay bit 75 mm Ø for soft soil and loose sand/gravel,

induction hardened part.no. R32-0116 0.44 kg pc. stock

Flushing Head 32/20 available for R 32* (1 -1/4"), R 38* (1 -1/2"), T 38*, T 45*,

for left hand rotary/percussion drilling, for flushing with water, grout or air,

thread Rd 32 x 1/8" (BSP 3/4”) male for grout hose, with lubrication nipple, to be

used in connection with holder only, incl. transport box,

length 265 mm, part.no. P32-001/.002/R32-0113/P32-003 14.00 kg pc. st. T38

complete set of spare seals for R 32 - T 45 flushing heads

(2 seals 63 x 78 x 11.4 mm plus 2 guide rings 63 x 68 x 6.3 mm)

part.no. T30-0369 set stock

Holder, spring action, for Flushing Heads for R 32*, R 38*, T 38*, T 45*,

to be fixed on to the mast of the drill rig, fixing position:

hammer fully extended and spring released

part.no. T30-0370 5.90 kg pc. stock

CTS Grout Swivel - T38m/T38m

for left hand rotary/percussion drilling and for flushing with water, grout or air

1” NPT male for grout hose connection

part.no. TAC-003 6.75 kg pc. stock

CTS Adaptor Couplers - T38/R32

part.no. MIC-0032 3.2 kg pc. stock

* please specify when ordering

Drill Connectors or flushing heads for other drill threads on request




8

CTS



November 2006

Page left blank intentionally




9

CTS



November 2006

CTS/TITAN 30/16 & 30/11

CTS/TITAN Injection Bore Hollow Bar System 30 / 16

TITAN Injection Hollow Bar, 30/16 mm, design load (60% GUTS) 132 kN.

left hand threaded, suitable for all 30/11 accessories,

in 3m lengths.

black part.no. T30-0341 2.87 kg/m pc. stock



left hand threaded,

in 3m lengths




left hand threaded,

in 3m lengths


INOX, stainless steel, material no. 1.4462, with approval Z-30.3-6

in 3 m lengths. part.no. T30-0373 3.42 kg/m pc. stock

CTS/TITAN 30/16 and 30/11 Injection Anchors are also available in other

lengths. Please ask us for pricing.

Galvanized, Metallized or EPOXY Coated CTS/TITAN Injection Anchors

and Accessories are also available. Please ask us for pricing.

Accessories

Spherical Collar Nut SW 46 x 35 mm. inclination ± 7.5

black, part.no. T30-0362 0.34 kg pc. stock

INOX Sperical Collar Nut, stainless steel,

material no. 1.4468, part.no. T30-0358 0.42 kg pc. stock

Coupling 38 Ø x 105 mm. with center-stop.


INOX Coupling, stainless steel,

material no. 1.4468, part.no. T30-0357 0.40 kg pc. stock

Bearing Plate, 200 x 200 x 8 mm, for shotcrete,


Bearing Plate INOX, 200 x 200 x 12 mm, stainless steel,

hole Ø 38 mm,

material no. 1.4301 part.no. T30-0359 3.85 kg pc. stock

Steel ball 80 mm Ø, hole Ø 32 mm, max. inclination ± 36°,

black part.no. P30-001 1.87 kg pc.

Plate for Steel Ball, 300 x 200 x 23 mm (without steel ball)

to be used on four double U-300 walers, spaced max. 150 mm

black part.no. PAC-002 13.00 kg pc.

Geotextile Fixing Plate, 285 mm Ø for CTS/TITAN 30/11 and 40/16

galv. part.no. P30-003 6.00 kg pc.




CTS/TITAN 30/16 & 30/11

10

CTS



November 2006

Accessories

Wedge Disc 30/11, 12°, allows 3 x 12° angle,

black, weldable part.no. T30-0361 0.91 kg pc.

Adaptor for Injection Hollow Bar 30/11 on drill bit 40/16

part.no. T30-0334 0.21 kg pc.

Drill Bits

TITAN Drill Bit - Button Type 42, (42 mm Ø), hardness HRC 54,

for hand-held rotary percussion drills, for soft rock and concrete

part.no. P30-004 0.28 kg pc.


with top and radial flushing holes, suitable for airtrack drilling machines

for harder rock and concrete



with top and radial flushing holes, suitable for airtrack drilling machines

for harder rock and concrete.

part.no. P30-005 0.34 kg pc.

TITAN Drill Bit - Button Type 55, (55 mm Ø),

for weathered soft rock and gravel


TITAN Drill Bit - Carbide Offset Cross Cut 46, (46 mm Ø)

carbide tipped, part.no. T30-0346 0.37 kg pc. stock

CTS/TITAN Drill Bit - Carbide 2” (51 mm)


CTS/TITAN Drill Bit - Carbide 2.5” (63 mm)




TITAN Drill Bit - Carbide Cross Cut 2-Step 75, (75 mm Ø)

drill bit for directional stability, cuts through several hard layers of soil/rock

part.no. T30-0347 0.84 kg pc.

TITAN Drill Bit - 3 Cut 76, (76 mm Ø)

with recess center buttons hardened to 57 Rc

part.no. P30-006 0.69 kg pc.

TITAN Drill Bit - Cross Cut 90 mixed Ground, (90 mm Ø)


TITAN Drill Bit - Clay bit 75 mm Ø for soft soil and loose sand/gravel.

induction hardened part.no. T30-0348 0.44 kg pc. stock

TITAN Drill Bit - Clay bit 95 mm Ø for soft soil and loose sand/gravel.

induction hardened part.no. T30-0003 0.55 kg pc. stock

Piling Cone 75, (75 mm Ø), with backwards pointing injection hole

part.no. T30-0364 0.68 kg pc.

Centralizer TITAN 30, 70 mm Ø, for 20 mm grout cover, cast iron

black part.no. T30-0335 0.23 kg pc. stock

Centralizer TITAN 30, 88 mm Ø, cast iron

to seal bore holes of 33 mm up to 56 mm Ø





11Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical


November 2006

CTS/TITAN 30/16 & 30/11CTS

Accessories

Bore Hole Stopper screws on to the anchor, material PE,

to seal bore holes of 33 mm up to 56 mm Ø

part.no. T30-0365 0.10 kg pc.

Eye bolt, 35 mm eye diam., SWL 30 kN

galvanized part.no. P30-008 0.50 kg pc.

Eyebolt, inside Ø, 40/30 mm, for shackles max. M 30,

SWL 150 kN

galvanized part.no. T30-0010 1.90 kg pc. stock

Load Indicator for 30/11, to indicate loads of 70, 160 and 180 kN,

retracts by a total of 30 mm, LOBA approved

galvanized part.no. T30-0367 0.42 kg pc. stock

Expansion Shell for 30/11 and 30/16 anchors for drill hole Ø 46 up to 56 mm

part.no. T30-0368 0.77 kg pc.

Self contained Flushing Head S 22 for 30/11, for left-hand hand-held hammers

(no holder required) part.no. T30-0386 5.96 kg pc. stock

Flushing Head 30/11, for hexagon S 22 (7/8"), for left hand rotary/percussive

drilling, for flushing with water, grout or air, thread Rd 32 x 1/8" (BSP 1/2") male for

grout hose, length 323 mm, to be used in connection with holder only

incl. transport box part.no. T30-0336 5.40 kg pc.

Complete set of spare seals for S 22 flushing head (2 pieces, 40 x 50 x 7 mm)

part.no. TAC-0018 set

Holder, spring action, for flushing head 30/11-S 22,

bolts on to the mast of the drill rig

part.no. TAC-0019 7.28 kg pc.

Flushing Head 30/11 available for R 32* (1-¼"), R 38* (1 -1/2"), T 38*, T 45*,

for left hand rotary and percussive drilling, for flushing with water, grout or air, thread

Rd 32 x 1/8" (BSP 3/4") male for grout hose, with lubrication nipple, to be used in

connection with holder only, incl. transport box,

length 265 mm, part.no. T30-0339/..0380/..0340/..0379/ 14.00 kg pc. stock

complete set of spare seals for R 32 - T 45 flushing heads

(2 seals 63 x 78 x 11,4 mm plus 2 guide rings 63 x 68 x 6,3 mm)

part.no. TAC-0005 set stock

Holder, spring action, for Flushing Heads for R 32*, R 38*, T 38*, T 45*,to be fixed on to the mast of the drill rig, fixing position: hammer fully extended and

spring released

part.no. T3AC-0020 5.90 kg pc. stock

*please specify when ordering

Drill Connectors or flushing heads for other drill threads on request




12

CTS



November 2006

CTS/TITAN 30/16 & 30/11

Grouting Connector for 30/11thread Rd 32 x 1/8" male, for high pressure grout-hose DN 20, with handle and

lubrication nipple

zinc plated part.no. T30-0333 0.92 kg pc.

CTS Grout Swivel - T38m/T38mfor left hand rotary/percussion drilling and for flushing with water, grout or air



CTS Adaptor Couplers - T38/TITAN30





13

CTS



November 2006

CTS/TITAN 40/16 & 40/20



continuously left hand threaded,

in lengths of 3 m.


INOX, stainless steel, material no. 1.4462,

in 3 m lengths part.no. T40-0299 7.00 kg/m pc. stock



in lengths of 3 m


CTS/TITAN 40/16 and 40/20 are also available in other lengths.

Please ask us for pricing.

Galvanized, Metallized or EPOXY Coated Injection Anchors and

Accessories are also available. Please ask us for pricing.

Accessories

Spherical Collar Nut SW 65 x 50 mm, inclination ± 7°.


INOX Sperical Collar Nut, stainless steel, material no. 1.4468


Coupling, 54 mm Ø x 140 mm, with center-stop, hardened, with 2 rubber seals


INOX Coupling, stainless steel,

material no. 1.4468 part.no. T40-0260 1.13 kg pc. stock

Bayonet Coupler 63 Ø x 228 mm, recoverable


Bearing Plate, 200 x 200 x 12 mm, hole Ø 56 mm,


Bearing Plate, 200 x 200 x 30 mm, hole Ø 56 mm, for anchorpiles,


INOX Bearing Plate, 200 x 200 x 15 mm, hole Ø 54 mm,

stainless steel,

material no. 1.4301 part.no. T40-0300 4.58 kg pc.

Steel ball 80 mm Ø, hole Ø 42 mm, max. inclination ± 36°,


Plate for Steel Ball, 300 x 200 x 23 mm (without steel ball)

to be used on four double U-300 walers, spaced max. 150 mm

black part.no. PAC-001 13.00 kg pc.

Wedge Disc 40/16, 12°, weldable





14

CTS



November 2006

CTS/TITAN 40/16 & 40/20

Accessories

TITAN Drill Bit - Clay bit 110 mm Ø for soft soil and loose sand/gravel,

induction hardened

part. no. T40-0255 1.28 kg pc. stock

TITAN Drill Bit - HPI-Clay bit 110 mm Ø for jet grouting up to 200 bars,

with 2 nozzles, 2,3 mm Ø,


TITAN Drill Bit - Clay bit 150 mm Ø

induction hardened


TITAN Drill Bit - Button Type 70, (70 mm Ø ), for soft rock and gravel,

hardness HRC 54, with top and radial flushing holes,

screw-on type.


TITAN Drill Bit - Carbide button drill bit 90, (90 mm Ø ),

screw-on type.

part.no. P40-003 1.27 kg pc.

TITAN Drill Bit - Carbide Cross Cut 70, (70 mm Ø), for hard rock,

screw-on type



carbide tipped,



carbide tipped,


TITAN Drill Bit - Cross Cut 90, (90 mm Ø), mixed soil with obstacles


TITAN Drill Bit - Cross Cut 115 (115 mm Ø), for soft soils, sand and cobbles and

soft rock, with top and radial flushingholes,

screw-on type

part.no. T40-0296 2 kg pc. stock

TITAN Drill Bit - Aggressive Soft Soil Bit, 100 mm Ø, for clay and mudstone,

screw-on type

part.no. T40-0253 0.83 kg pc.

TITAN Drill Bit - Carbide cross cut 3-step, cuts through several hard layers,

screw-on type

part.no. P40-004 1.2 kg pc.

Piling Cone, (90 mm Ø), for displaceable soils, clay or high water table,

screw-on type

part.no. T40-0264 2.06 kg pc.

Centralizer 88 mm Ø, for 20 mm grout cover,

cast iron


Geotextile Fixing Plate, 285 mm Ø for CTS/TITAN 30/11 and 40/16

galv. part.no. P30-005 6.00 kg pc.




15

CTS



November 2006

CTS/TITAN 40/16 & 40/20

Accessories

Bore Hole Stopper, material PE, to seal bore holes, up to 80 mm Ø,

screw-on type, 100 mm long,


Eye bolt, hole 40/30 mm, SWL 300 kN

galvanized part.no. T40-0303 1.90 kg pc.

Load Indicator for 40/16, to indicate loads of 200, 300 and 400 kN, retracts by a

total of 40 mm, LOBA approved

galvanized part.no. P40-012 0.59 kg pc.

Flushing Head 40/16 for hexagon S 22 (7/8"), for left hand rotary and percussive

drilling, for flushing with water, grout or air, thread Rd 32 x 1/8" (BSP 1/2") male for

grout hose, length 368 mm, to be used in connection with holder only, incl. transport

box,

part.no. P40-013 6.40 kg pc.

Complete set of spare seals for S 22 flushing heads

(2 pieces, 40 x 50 x 7 mm)


Holder, spring action, for Flushing Head 40/16-S22,

bolts on to the mast of the drill rig,


Flushing Head 40/16 available for R32*(1-1/4"), R38*(1-1/2"), T38*, T45* ,

for left hand rotary and percussive drilling, for flushing with water, grout or air, thread

Rd 32 x 1/8 " (BSP 3/4") male for grout hose, with lubrication nipple, length 265 mm,

to be used in connection with holder only, incl. transport box,

part.no. T40-0279/..0244/..0243/..024513.30 kg pc. stock

Complete set of spare seals for R 32 - T 45 flushing heads

(2 seals 63 x 78 x 11,4 mm plus 2 guide rings 63 x 68 x 6.3 mm)


Holder, spring action, for Flushing Heads for R 32*, R 38*, T 38*, T 45*,

to be fixed on to the mast of the drill rig

fixing position: hammer fully extended and spring released


Flushing Head R 55 (2-1/4"), for left hand rotary and percussive drilling, for flush-

ing with water, grout or air, thread Rd 32 x 1/8" (BSP R 3/4") male for grout hose,

with lubrication nipple, length 365 mm, to be used in connection with holder only,

incl. transport box

part.no. T40-0295 34.20 kg pc.

Complete set of spare seals for R 55 flushing heads

( 2 seals 100 x 120 x 12 mm plus 2 guide rings 100 x 105 x 9.7 mm)


Holder for Flushing Head R55, C 64, RT 70, C90 and H112

for all drill rigs


*please specify when ordering

Drill Connectors or flushing heads for other threads on request.




16

CTS



November 2006

CTS/TITAN 40/16 & 40/20

Grouting Connector, for high pressure grout-hose DN 20

thread Rd32 x 1/8” male, with handle and lubrication nipple

galvanized part no. T40-0241 1.5 kg pc.

CTS Grout Swivel - T38m/T38mfor left hand rotary/percussion drilling and for flushing with water, grout or air



CTS Adaptor Couplers - T38/TITAN40





17

CTS



November 2006

CTS/TITAN 52/26

CTS/TITAN Injection Bore Hollow Bar System 52/26

CTS/TITAN Injection Hollow Bar 52/26, design load (60% GUTS) 557 kN, left handthreaded, right-hand threaded available on special order

in 3 m lengths.

black left hand thread part.no. T52-0160 9.83 kg/m pc. stock

Accessories

Spherical Collar Nut SW 80 x 70,

max. inclination ± 10° of washer plate,


Coupling 70 mm Ø x 160 mm, with center-stop, hardened, with 2 rubber seals,



part.no. P52-006 11.70 kg pc.

Adapter for Bayonet Coupler, recoverable

part.no. P52-007

Bearing Plate, 220 x 220 x 35 mm for Anchorpiles,

hole Ø 65 mm

black part.no. T52-0157 13.1 kg pc.

Steel Ball, 100 mm Ø, black,

54 mm bore in the steel ball, max. inclination 36°

part.no. P52-001 3.25 kg pc.

Plate for Steel Ball 300 x 200 x 35 mm, hole Ø 93

without ball, black part.no. P52-001a 14.4 kg pc.

Wedge Disc, 12°, allows max. 0 x 24°, black,


Drill Bits

TITAN Drill Bit - Cross Cut 115, (115 mm Ø), for soft soils, sand and cobbles and

soft rock with top and radial flushing holes,

screw-on type part.no. T52-0147 2.51 kg pc. stock


carbide tipped part.no. T52-0150 2.04 kg pc. stock

TITAN Drill Bit - Clay bit 130 mm Ø,

screw-on type part.no. T52-0165 2.37 kg pc. stock

TITAN Drill Bit - HPI-Clay bit 130 mm Ø, for jet grouting up to 200 bar

with 2 nozzles, 2,3 mm Ø,

part.no. P52-003 2.40 kg pc. stock

TITAN Drill Bit - Button Type 115, (115 mm Ø), for hard or high quarzite rock car-

bide tipped

screw-on type


CTS/TITAN 52/26 Injection Anchors are also available in other lengths.







18

CTS



November 2006

CTS/TITAN 52/26

Accessories

Centralizer 112 mm Ø, cast iron


Flushing Head 52/26 available for R32*(1-1/4"), R38*(1-1/2"), T38*, T45*,for rotary/percussive drilling, for flushing with water, grout or air, thread Rd 32 x 1/8"

(BSP 3/4") male for grout hose, with lubrication nipple, length 365 mm, to be used in

connection with holder only, incl. transport box,

part.no. T52-0172/..0142/..0164/..0158/ 18.80 kg pc. stock

complete set of spare seals for flushing heads R 32 - T 45(2 seals 63 x 78 x 11,4 mm plus 2 guide rings 63 x 68 x 6,3 mm)


Holder, spring action, for Flushing Heads for R 32*, R 38*, T 38*, T 45*,to be fixed on to the mast of the drill rig

fixing position: hammer fully extended and spring released


Flushing Head R 55 ( 2- 1/4"), for rotary/percussive drilling, for flushing with water,

grout or air, thread Rd 32 x 1/8" or BSP 3/4" and 1-1/2" female for grout hose, with

lubrication nipple, length 365 mm, to be used in connection with holder only, incl.

transport box

part.no. T5R-0050 34.30 kg pc.

complete set of spare seals for R 55 flushing head

(2 seals 100 x 120 x 12 mm plus 2 guide rings 100 x 105 x 9,7 mm)



for all drill rigs


Grouting Connector for 52/26 , for high pressure grout-hose DN 20, thread Rd 32

x 1/8" male, with handle and lubrication nipple, galvanized

part.no. P52-005 1.80 kg pc.




19

CTS



November 2006

CTS/TITAN 73/56, 73/53 & 73/45


CTS/TITAN Injection Hollow Bar 73/56, design load (60% GUTS) 656 kN

continuously right-hand threaded

in 6.25 m lengths

black, part.no. T73-0172 10.75 kg/m pc. stock




in 3 m lengths





in 3 m lengths





in 3 m lengths


Accessories

Spherical Collar Nut SW 95 x 70


Coupling 89 Ø x 225 mm,

St. 52-3, with internal rubber seal,



part.no. P73-001 11.70 kg pc.

Bearing Plate, 250 x 250 x 40 mm for Anchorpiles,

hole Ø 80 mm, max. inclination ± 6°,

black part.no. T73-0166 18.00 kg pc.

Wedge Disc, 12° for 73/53, 200 mm, allows max. 2 x 12°,


Centralizer 130 mm Ø, cast iron,


CTS/TITAN 73 Injection Anchors are also available in other lengths.







20

CTS



November 2006

CTS/TITAN 73/56, 73/53 & 73/45

Accessories

TITAN Drill Bit - Cross Cut, 130 mm Ø, for mixed soil with obstacles,

screw-on type


TITAN Drill Bit - Cross Cut, 175 mm Øscrew-on type


TITAN Drill Bit - Clay Bit 200 mm Ø,

screw-on type


TITAN Drill-Bit - Button Type 130, (130 mm Ø)

with carbide buttons, screw-on type

part no. T73-0158 5.5 kg pc. stock

TITAN Drill Bit - Carbide Cross Cut 3 Step 130 (130 mm Ø)

drill bit for directional stability, cuts through several hard layers of soil/rock

part no. P73-0006 5.8 kg pc.

Flushing Head R 55 (2¼"), for right hand rotary and percussive drilling, for flush-

ing with water, grout or air, thread Rd 32 x 1/8" (BSP 3/4") male for grout hose, with

lubrication nipple, length 365 mm, to be used in connection with holder only, incl.

transport box,



(2 seals 100 x 120 x 12 mm plus 2 guide rings 100 x 105 x 9.7 mm)


Rotary Flushing Head R 55 (2 1/4"), self contained, length 405 mm, no holder

required, 120 mm wrench required, incl. transport box,

part.no. T73-0153 43.70 kg pc.

Flushing Head H 112, for right hand rotary and percussive drilling, for flushing with

water, grout or air, thread BSP 2" male for grout hose, with lubrication nipple, length

300 mm, to be used in connection with holder only, incl. transport box,

part.no. T73-0151 53.20 kg pc.

complete set of spare seals for flushing head H 112


part.no. TAC-0022 pc.


for all drill rigs





21

CTS



November 2006

CTS/TITAN 103/78 & 103/51


CTS/TITAN Injection Hollow Bar 103/78, design load (60% GUTS) 1369 kN,


in 3 m lengths.





in 3 m. lengths.


Accessories

Spherical Collar Nut SW 125 x 80,


Coupling Nut 123 mm Ø x 255 mm,

with internal rubber seal, black

2282 KN part.no. T03-0109 7.47 kg pc. stock

Coupling Nut 132 mm Ø x 290 mm,


3460 KN part.no. T03-0121 12.6 kg pc.


part.no. P03-002 19.00 kg pc.

Bearing Plate 300 x 300 x 50 mm,

black, part.no. T03-0113 32.60 kg pc.

Drill Bits

TITAN Drill Bit - Cross Cut, 175 mm Ø, for mixed soil with obstacles,

screw-on type


TITAN Drill Bit - Clay Bit 220 mm Ø,


TITAN Drill Bit - Clay Bit 280 mm Ø

part no. T03-0122 13.9 kg pc. stock

TITAN Drill Bit - Button Type 175, (175 mm Ø), with carbide buttons,

screw-on type


Centralizer, 165 mm Ø, cast iron,


CTS/TITAN 103/78 & 103/51 Injection Anchors are also available in other

lengths. Please ask us for pricing.






22

CTS



November 2006

CTS/TITAN 103/78 & 103/51

Accessories

Flushing Head R 55 (2¼"), for right hand rotary and percussive drilling, for flush-

ing with water, grout or air, thread Rd 32 x 1/8" or BSP 3/4" and 1-1/2" female, for

grout hose, with lubrication nipple, length 365 mm, to be used in connection with

holder only, incl. transport box,





Flushing Head, H 112 for right hand rotary and percussive drilling , for flushing with

water, grout or air, thread BSP 2" male, for grout hose, with lubrication nipple, length

300 mm, to be used in connection with holder only, incl. transport box


complete set of spare seals for H 112 flushing head




for all drill rigs





23

CTS



November 2006

CTS/TITAN 130/60




in 3 m lengths.

black, part.no. T13-0001 79 kg/m pc.

CTS/TITAN 130/60 Injection Anchors are also available in other lengths.




Accessories

Spherical Collar Nut

black, part.no. T13-0003 pc.

Coupling Nut


black part.no. T13-0002 pc.

TITAN Drill Bit - Carbide Button Bit 220 mm Ø,

screw-on type

part.no. T13-0004 pc.




CTS/TITAN

24

CTS



November 2006

CTS/TITAN Hollow Bar Technical Data 3

Drill Bit Selection Chart 5

CTS/TITAN R32 7

Accessories 7

CTS/TITAN T30/11 & T30/16 9

Injection Hollow Bars 9

Accessories 9

CTS/TITAN T40/16 & T40/20 13


Accessories 13

CTS/TITAN T52/26 17


Accessories 17

CTS/TITAN T73/56 T73/53 & T73/45 19


Accessories 19

CTS/TITAN T103/78 & T103/51 21


Accessories 21

CTS/TITAN T130/60 23


Accessories 23

cts/titan injection bore system - con-tech · pdf filects/titaninjection bore system tie back...

Documents