craig riley - no dig equipment · towing heads size (mm) id min (mm) id max (mm) weight part # 50...
TRANSCRIPT
Craig Riley15 Wildfire Road Maddington WA 6109
PO Box 2 Maddington WA 6989
Ph: 94930642Fax: 94930672
Mobile: 0411 475 646
Email: [email protected]
Ph: 94930642Fax: 94930672
Email: [email protected]
15 Wildfire Road Maddington WA 6109
PO Box 2 Maddington WA 6989
Peter Senior
WHAT'S INSIDE
Drilling The Pilot Hole..........................................................................................................4Vermeer® compatible ................................................................................................................................. 5Ditch Witch® compatible ............................................................................................................................. 5Rock Bit and Transmitter Housing...............................................................................................................5NEW Crocodile............................................................................................................................................ 6Bear Claw.................................................................................................................................................... 7Sand Blade.................................................................................................................................................. 7Starter Rods................................................................................................................................................. 8Collars......................................................................................................................................................... 8Drive Chucks & Saver-Subs........................................................................................................................ 8
Pulling The New Pipe...........................................................................................................9Standard Towing Heads............................................................................................................................. 10Towing Socks, Slings and Grips................................................................................................................. 10Screw-in Duct Pullers................................................................................................................................ 10Ripper Reamer........................................................................................................................................... 11Compaction Reamer.................................................................................................................................. 12Rock Reamer - Hole Opener.....................................................................................................................13Barrel Reamer........................................................................................................................................... 14Fly Cutter................................................................................................................................................... 14Reamer Stabiliser...................................................................................................................................... 14Easy Reamer............................................................................................................................................. 15Pulling Swivels........................................................................................................................................... 15
Drilling Accessories...........................................................................................................16Digitrak Falcon® Locators......................................................................................................................... 17Other Accessories...................................................................................................................................... 18
Drilling The Pilot HoleIn this section, you will find all necessary tools to drill forward horizontally
• Transmitter Housings
• Rock Bit and Transmitter Housing
• Horizontal Directional Drilling Blades
• Starter Rods
• Collars
• Drive Chucks and Saver Sub compatible for Vermeer HDD Drills
www.NoDigEquipment.com.au [email protected] Ph : 08 9493 0642 page 4
Vermeer®
compatible
Our Vermeer® compatible transmitter housings are available in2.3⁄4” or 3” OD to match your Directional Drill. All compatible housings are designed to accept 2-cell DCI Digitrak® transmitters. Our unique 3-pieces housing assembly consists of one housing body, nose piece and tail sub which delivers a significant gain in service life over Original Equipment Manufacturer (OEM) housings.Available for all drills from the D7x11 to the D33x44.
Ditch Witch®
compatible
Our Ditch Witch® compatible transmitter housings are available tomatch your Directional Drill and your Ditch Witch Drilling Blade (5 Bolts pattern).All housings are designed to accept Subsite® Beacons. Our unique 3-piece housing assembly consists of one housing body, nose piece and tail sub which delivers a significant gain in service life over OEM housings. Available for all drills from the JT922 to the JT3020M1.
Vermeer® and Ditch Witch® Compatible Transmitter Housings
Vermeer® Compatible Part #
2.3/4” dia. suit D6x6 to D7x11 THV275
3” dia. (7 Bolts pattern) suit D16x20a to D33x44 THV300
Ditch Witch® Compatible
2” dia. (3 Bolts pattern) suit JT520 THD200
2.3/4” dia. (5 Bolts pattern) suit JT920 to JT922 THD275
3” dia. (5 Bolts pattern) suit JT1720 to JT3020M1 THD300
Prices include tail sub to suit your HDD Drill & the double jet nose piece
Rock Bit and Transmitter HousingThe Rock Bit comes with the transmitter housing to suit Vermeer®, Ditch Witch® and other HDD Drills .This universal Rock Bit Housing can be adapted to any Horizontal Directional Drill on the market using a simple tail/adapter sub.The Rock Bit Housings are designed to take standard DigiTrak®, Radio Detection® andSubsite® transmitters.
Rock Bit & Transmitter Housing
Vermeer® Compatible Part #
2.3/4” dia. suit D6x6 to D7x11, cut 3.5” to 4” hole RBHV275
3.1/4” dia. suit D16x20 to D33x44, cut 4.5” to 5” hole RBHV325
3.1/2” dia. suit D16x20 to D33x44, cut 5.5” to 6” hole RBHV350
Ditch Witch® Compatible
2.3/4” dia. suit JT922, cut 3.5” to 4” hole RBHD275
3.1/4” dia. suit JT1720 to JT3020, cut 4.5” to 5” hole RBHD325
3.1/2” dia. suit JT1720 to JT3020, cut 5.5” to 6” hole RBHD350
Prices include the housing, the tail sub to suit your HDD Drill & the Rock Bit
www.NoDigEquipment.com.au [email protected] Ph : 08 9493 0642 page 5
The Double Jets Nose Piece increase thejetting performance and comes with everyTransmitter Housing compatible withVermeer® and Ditch Witch® HDD Drills.
Tungchip Hardfacing as StandardTungchip hardfacing is a technique where tungsten chip is directly deposited onto the weld matrix of the hardfacing material.This provide excellent toughness and superior wear resistance for prolonged tool life.Available on all our blades as standard.
NEW Crocodile
The most cost effective solution for drilling inHard Pack Clay and Rocky ground conditions.
These blades provide reduced torque in hard ground conditions, which means you require less power. Hence you save wear and tear on your machine.
Crocodile Blade
Vermeer® Compatible Part #
7 Hole pattern, 3” cut, suit D7x11 BVC80
7 Hole pattern, 4” cut, suit D16x20 to D24x40 BVC100
Ditch Witch® Compatible
5 Hole pattern, 4” cut, suit JT1720 to JT2720 BDC100
• Serrated Carbide teeth for cutting in the hardest conditions
• Additional Tungchip hardfacing for extra-wear protection
• Tapered design to reduce torque in compact ground
www.NoDigEquipment.com.au [email protected] Ph : 08 9493 0642 page 6
New Crocodile BCV100
DID YOU KNOW ?The Tungsten is 2 time harder than the steel and a lot more
wear resistant, so when added on the weld matrix, the
hardfacing become a really strong crust.
Bear Claw
Vermeer® Compatible Part #
7 Hole pattern, 3.5" cut, suit D7x11 BVB80
7 Hole pattern, 4" cut, suit D16x20 to D24x40 BVB100
7 Hole pattern, 5.25" cut, suit D24x40 BVB125
Ditch Witch® Compatible
5 Hole pattern, 3" cut, suit JT922 BDB75
5 Hole pattern, 4" cut, suit JT1720 to JT2720 BDB100
6 Hole pattern, 5.25” cut, suit JT3020 BDB125
Bear Claw
A must for any directional drillers tool box.
The cutting teeth on this blade provides good cutting action in pinnacle limestone and other mixed ground conditions.
Ballistic carbide cutters allow ripping through tough material, whilst still providing great steer-ability in sandy and soft ground.
• Carbide teeth shred through the hardest soils
• Tungchip hardfacing along all wear edges improve blade life
• Made from Bisalloy plate for high strength and wear resistance
Sand Blade
Ideal for sand and loam soil conditions
An economical long lasting blade that continues to perform in sandy ground conditions.
• Made from Bisalloy plate for high strength and wear resistance
• Tungchip hardfacing for maximum wear resistance
Sand Blade
Vermeer® Compatible Part #
7 Hole pattern, 3” cut, suit D7x11 BSV80
7 Hole pattern, 4” cut, suit D16x20 to D24x40 BSV100
7 Hole pattern, 5” cut, suit D24x40 BSV125
Ditch Witch® Compatible
5 Hole pattern, 3” cut, suit JT922 BSD80
5 Hole pattern, 4” cut, suit JT1720 to JT2720 BSD100
6 Hole pattern, 5” cut, suit JT3020 BSD125
www.NoDigEquipment.com.au [email protected] Ph : 08 9493 0642 page 7
Sand Blade + Tungchip BSV100
Bear Claw + Tungchip BBV100
Drive Chuck Saver-Sub
Starter Rods
Tapered section provides better tool life with lower tooling costs
• Manufactured from 4140 heat treated alloy
• Extra Large 3/8” bolt retains slide collar
• Extra thickness for improved wear protection
Starter Rods
Vermeer® Compatible Part #
suit D7x11 SRV711
suit D16x20 SRV1640
suit D20x22 SRV2022
suit D24x40 SRV2440
suit D36x50 SRV3650
Ditch Witch® Compatible
suit JT922 SRD922
suit JT2020 - JT2720 SRD2720
suit JT3020 – Ezconnect II SRD30202
suit JT3020 – Ezconnect III SRD30203
suit JT4020 SRD4020
Collars
Vermeer® Compatible Part #
Hex Collar suitable for D7x11 CV711
Hex Collar suitable for D16x20 to D36x50 CV3650
Ditch Witch® Compatible
Oct Collar suitable for JT922 CD922
Oct Collar suitable for JT1720 to JT2720 CD2720
Oct Collar suitable for JT3020 Ez. II CD30202
Oct Collar suitable for JT3020 Ez. III CD30203
CollarsProtect your Starter Rod with Tungsten carbide reinforced collars• Completely heat-treated for maximum durability
• Hardfacing to reduce wear and improve life
Tungchip Hardfaced
Drive Chucks & Saver-Subs
Replaceable inexpensive Saver-Sub• Manufactured from 4140 heat treated alloy
• CNC machined Chucks and Saver-Subs
• Suitable for Vermeer drills D7x11 – D24x40
Drive Chucks and Saver-Subs
Vermeer® Compatible Part #
Drive Chuck c/w Saver Sub for D7x11 DCSV711
Drive Chuck c/w Saver Sub for D16x20 DCSV1620
Drive Chuck c/w Saver Sub for D20x22 DCSV2022
Drive Chuck c/w Saver Sub for D24x40 DCSV2440
www.NoDigEquipment.com.au [email protected] Ph : 08 9493 0642 page 8
Pulling The New PipeIn this section, you will find all necessary tools to ream the hole and safely pull the new service
• Standard Towing Heads
• Towing Socks, Slings and Grips
• Screw-in Towing Heads
• Ripper Reamer
• Compaction Reamer
• Rock Reamer – Hole Opener
• Barrel Reamer
• Fly Cutter
• Reamer Stabilizer
• Easy Reamer
• Pulling Swivel
www.NoDigEquipment.com.au [email protected] Ph : 08 9493 0642 page 9
Standard Towing Heads
These tools are a must for safely towing PE pipes.Our Towing Heads provide one of the most efficient ways to allow the safe towing of PE pipes into position. A standard part of any HDD operation.
• Aluminium towing cones for larger sizes reduce weight
• Higher performance in the toughest conditions
• Zinc plated finish to resist corrosion
• Jaws made from 4140 alloy steel
Towing Heads
Size(mm)
ID min(mm)
ID max(mm)
Weight Part #
50 39.0 48.0 1.0 TH50
63 48.0 60.0 1.70 TH63
90 67.0 86.0 2.80 TH90
110 88.0 101.0 4.20 TH110
125 96.0 116.0 5.20 TH125
140 107.0 137.0 8.60 TH140
160 128.0 154.0 11.60 TH160
180 143.0 171.0 15.00 TH180
Larger sizes also made to order
Towing Socks, Slings and Grips
Cable Socks and Grips
Hose OD mm
Break Strength kg
Length mm Part #
8-14 1300 400 TS14
14-20 1300 550 TS20
20-30 2800 640 TS30
30-40 5500 870 TS40
40-50 5500 970 TS50
50-60 5500 1250 TS60
60-70 (LV) 9300 1300 TS70
70-85 (HV1) 9300 1350 TS85
85-100 9300 1620 TS100
100-120 (HV2) 12500 1830 TS120
120-140 16000 2200 TS140
140-180 16000 2370 TS180
Our Towing Socks can be use for installing cables and small ducts. Standard cable socks are available for common underground cable sizes including single LV and multiple HV cables.
• Re-usable over and over again
• The harder you pull, the tighter it grips
• Manufacture from high tensile galvanised wire
• Custom sizes can be manufactured on request
• Available in Stainless Steel for extended durability
Screw-in Duct Pullers
• Manufactured from 4140 alloy steel
• No moving parts means maintenance free
• Zinc plated for corrosion resistance and durability
Screw-in Towing Heads
Size mm
ID min
ID max Part #
16 12 15 TH16
20 14 18 TH20
25 19 24.5 TH25
32 24 28.5 TH32
40 30 38 TH40
www.NoDigEquipment.com.au [email protected] Ph : 08 9493 0642 page 10
SCR25
Ripper Reamer
Ideal for sticky and hard pack clay conditions• Carbide Cutters for superior cutting in hard conditions
• Angled blades for effective mud mixing
• Cutters are precisely placed to provide smooth even cutting action.
• Designed for high mixing and pumping action in stickyclay ground conditions.
Ripper Reamer – Clay reamer
Part #
200mm Cut Diameter, 2 1/2" shaft RR200
250mm Cut Diameter, 2 1/2" shaft RR250
300mm Cut Diameter, 2 1/2" Shaft RR300
350mm Cut Diameter, 2 1/2" shaft RR350
400mm Cut Diameter, 2 3/8 API shaft RR400
500mm Cut Diameter, 2 3/8 API shaft RR500
Larger reamers also made to order
NB : All our Ripper Reamer are sold with the pulling eye and the front connection compatible to Vermeer D7x11 to D24x40 as well as Ditch Witch JT522 to JT3020. Simply tell us what drill you want the connection for and we will fit the right front adapter sub.
We can provide you with bigger connections, simply contact us and we will get the best price.
Screw-in Swivel Option
www.NoDigEquipment.com.au [email protected] Ph : 08 9493 0642 page 11
Screw-in Swivel Option - SW12
RR350 : Ripper Reamer 350mm dia.
Prices include pulling Prices include pulling eye and front eye and front connectionconnection
12T12T Screw-in Swivel : Add $680 Screw-in Swivel : Add $6808T8T Screw-in Swivel : Add $480 Screw-in Swivel : Add $480
Compaction Reamer
Compaction Reamer – Sand reamer
Part #
115mm Dia., 2 1/2" shaft, (Optional Swivel) RC115
150mm Dia., 2 1/2" shaft, (10T Built in Swivel) RC150
200mm Dia., 2 1/2" shaft, (10T Built in Swivel) RC200
250mm Dia., 2 1/2" shaft, (10T Built in Swivel) RC250
300mm Dia., 2 1/2" shaft, (10T Built in Swivel) RC300
350mm Dia., 2 1/2" shaft, (10T Built in Swivel) RC350
400mm Dia., 2 3/8 API (20T Built in Swivel) RC400
500mm Dia., 2 3/8 API through shaft RC500
600mm Dia., 2 3/8 API through shaft RC600
• Ideal for sandy and mixed ground conditions
• Built-in swivel on reamers 150mm dia. and up
• Carbide bullet bits grind through tough ground conditions
• Cost effective reamer to suit many ground conditions
Unique troweling edge maintains and improves the filter cake as well as increasing hole stability
www.NoDigEquipment.com.au [email protected] Ph : 08 9493 0642 page 12
BEST BEST
REAMER
REAMER
IN SANDIN SAND
Our new Compaction Reamers suit a wide variety of ground conditions from wet running sands through to soft rock. Ballistic carbide cutters ensure optimal grinding action.
Additional trowelling length provides good in hole support. Large mud channel provides good spoil clearing which allow faster removal of cuttings reducing the possibility of frack out.
All our Compaction Reamer are sold with a build-in swivel or a pulling eye for the RC115 and the front connection compatible to Vermeer D7x11 to D24x40 as well as Ditch Witch JT922 to JT2720. Simply tell us what drill you want the connection for and we will fit the right front adapter sub.
Deep channels allow Deep channels allow faster removal of faster removal of cuttings reducing cuttings reducing
possibility of frack out possibility of frack out and increase and increase productivityproductivity
Troweling Edge
RC350 with Ditch Witch compatible adapter sub
Rock Reamer - Hole Opener
Custom built Hole Openers for back reaming in rock to 200 MPa. Soft and hard formation cutter options available. Reamers can be configured with built-in stabiliser for single package reaming.
• Ideal for Hard Rocky conditions
• Built-in Stabiliser options available
• Hard and soft cutters available for varying ground conditions
• Reamers with through shaft to allow reamer stacking
Here is a sample of some Back Reamers we have manufactured for our clients. Tell us the size of the pipe you need to install, the pull-back power of your machine and we will design the best Hole Opener for your needs.
Excellent turnaround time
www.NoDigEquipment.com.au [email protected] Ph : 08 9493 0642 page 13
Standard API threads
3 or more legs reamers can be built depending on your budget and requirements.
Stay straight in the hole with our built-in stabiliser Hole Opener.
Barrel Reamer Barrel Reamer
Part #
Barrel Reamer 2 3/8" API reg, 300mm Dia. pack size RB300
Barrel Reamer 2 3/8" API reg, 400mm Dia. pack size RB400
Barrel Reamer 3 1/2" API reg, 500mm Dia. pack size RB500
Barrel Reamer 3 1/2" API reg, 600mm Dia. pack size RB600
Our Barrel Reamer is the standard for larger rigs, provided with API threads and back cuttersfor back or forward reaming.
• Interchangeable nozzles to vary jet sizes and pressures
• Ideal for sand and loam soil conditions
• Grind through tough ground conditions
• Shafts threaded to suit your application
• Replaceable carbide cutters
Fly Cutter
Part #
Fly Cutter 300mm Dia. Cut Size RF300
Fly Cutter 400mm Dia. Cut Size RF400
Fly Cutter 500mm Dia. Cut Size RF500
Fly Cutter 600mm Dia. Cut Size RF600
Fly Cutter 700mm Dia. Cut Size RF700
Fly Cutter
Fly Cutter Back Reamers are ideal for mixed ground conditions, large openings allow cobbles to pass with great mixing action.
• Ideal for clay and mixed soil conditions
• Carbide Shark Teeth grind through tough ground conditions
• Hardfaced for extra wear protection
• Stabilising ring to provide clean smooth hole
• Shafts threaded to suit your application
Reamer Stabiliser
Because every job is different, No Dig Equipment will manufactureReamer Stabilisers to order.
• Run in conjunction with your Barrel Reamer, Fly Cutter or HoleOpeners
• Keeps your hole straight and true
• Hardfaced for extra wear protection
• Shafts threaded to suit your application
www.NoDigEquipment.com.au [email protected] Ph : 08 9493 0642 page 14
All BARREL REMEAR, All BARREL REMEAR, FLY CUTTER and FLY CUTTER and
STABILIZER are made to STABILIZER are made to order.order.
Contact us and we will Contact us and we will work with you to make work with you to make sure it will fit all your sure it will fit all your
requirementsrequirements
Easy Reamer
Fitted with a 8T Swivel, you can now order an Easy Reamer to suit any directional drill rig. Easy Reamers can be made to order, tellus what drill you use and we manufacture your cheapest back reamer ever.
Easy Reamer
Part #
Vermeer® Compatible Easy Reamer, 100mm cut, suit D7x11 to D24x40
SR4VSW8
Vermeer® Compatible Easy Reamer 175mm cut, suit D7x11 to D24x40
SR6VSW8
Ditch Witch® Compatible Easy Reamer, 100mm cut, suit JT1720 to JT2720
SR4DSW8
Ditch Witch® Compatible Easy Reamer, 175mm cut, suit JT1720 to JT2720
SR6DSW8
Ideal for sticky and hard pack clay and mixed ground conditions• Bore the hole straight away with the New Easy Reamer
• The most cost effective Back Reamer available for smaller ducts
Pulling Swivels
Swivels & DUB Swivels
Part #8T Swivel SW8
12T Swivel SW12
5T DUB Swivel SWD5
8T DUB Swivel SWD8
12T DUB Swivel SWD12
20T DUB Swivel SWD20
40T DUB Swivel SWD40
• Heavy duty bearings capable of handling both pulling and radial loads.
• Specially designed seals to prevent mud and water damaging the bearings.
• Designed to be easily serviceable with off the shelf parts.
www.NoDigEquipment.com.au [email protected] Ph : 08 9493 0642 page 15
The Pulling Swivel is a necessary and important part of every HDD job. Our swivels are able to withstand up all the tensile forces caused by the pull-back, rotational and side loads imposed by the bore.
SWD12
SW12
SR6VSW8 c/w 8T Swivel
Drilling AccessoriesIn this section, you will find some of the most common accessories for directional drillers
• Digitrak Locators
• Baroid Drilling Fluids
• Other Accessories
www.NoDigEquipment.com.au [email protected] Ph : 08 9493 0642 page 16
Digitrak® Locators
No Dig Equipment is an Authorised DCI® DigiTrak® dealer in Western Australia.
For more information visit nodigequipment.com.au/digitrak
DigiTrak Falcon F5®
Your Falcon F5 System includes: Falcon F5 Receiver, Aurora 8.4 in. Touchscreen Display and a 15 in. Falcon F5 Transmitter
• F Series Li-ion/NiMH charger with two Li-ion battery packs
• Carry case(s)
• Operator's manuals on USB flash drive
• Aurora 1.5” RAM mount on magneticbase and DC power cord
• 13” 90-degree TNC antenna
DigiTrak Falcon F2®
Your Falcon F2 System includes: Falcon F2 Receiver, Aurora 8.4 in. Touchscreen Display and a 15 in. Falcon F2 Transmitter
• F Series Li-ion/NiMH charger with two Li-ion battery packs
• Carry case(s)
• Operator's manuals on USB flash drive
• Aurora 1.5” RAM mount on magneticbase and DC power cord
• 13” 90-degree TNC antenna
DigiTrak Falcon F1®
Your Falcon F1 System includes: Falcon F1 Receiver, Falcon Compact Display (FCD) and a Falcon F1 Transmitter
• NiMH charger with three NiMH battery packs
• Carry case(s)
• Operator's manuals on USB flash drive
www.NoDigEquipment.com.au [email protected] Ph : 08 9493 0642 page 17
Other Accessories
Beyond our manufactured products we also offer a variety of accessories such as batteries for your DigiTrak® sonde and locators, String Line, Duct Tape, WD40, grease and rags.
www.NoDigEquipment.com.au [email protected] Ph : 08 9493 0642 page 18
Anti-Seize Rod GreaseDuct Tape
Bulk Batteries to suit Digitrak Transmitter
Lubricant and Cleaner WD40
Rags - Fleece
Nylon Braided Brick Line
www.NoDigEquipment.com.au [email protected] Ph : 08 9493 0642 page 19
www.NoDigEquipment.com.au [email protected] Ph : 08 9493 0642 page 20