cou800ol · connex 800mm intermediate leg frame. 22.01.2017. 1 2 3. 1. this assembly instruction is...
TRANSCRIPT
COU800OL
Connex 800mm Outer Leg Frame
22.01.2017
1 2 3 4
1
1,2,3...
TO
OL
S R
EQ
UIR
ED
FO
R A
SS
EM
BL
YD
ON
T S
TR
UG
GL
E2
MA
N L
IFT
AL
WA
YS
HA
ND
LE
ITE
MS
WIT
H C
AR
EIF
UN
SU
RE
CA
LL
FO
R A
SS
IST
AN
CE
KE
EP
FIT
TIN
GS
AW
AY
FR
OM
CH
ILD
RE
N
2
Please check that you have all the Components!
3
1 2+ 3
4
800mm Outer Leg Frame Fixed Length Beam
1200 / 1400 / 1600mm
Desk Top
1200 / 1400 / 1600mm
Please check that you have all the Fittings! (Fittings supplied with leg frames)
1 2+
800mm Outer Leg Frame
x 4
M6x60mm Connect Bolt
x 10
M6x10mm Countersunk Bolt
x 4
M6 Nylon Insert
4mm Allen Key
4
1
Step 1Attach the first beam tothe end leg using the M6bolts provided.
Loosely thread the boltsinto the face of the legbefore threading thebolts to the underside ofthe leg.
Once all bolts arethreaded you can fullytighten them using the4mm Allen Key.
x 5
If you are assembling this as part of a larger configuration please
refer to the intermediate leg frame assembly instructions before
proceeding with the next steps.
2
Step 2Attach the remainingouter leg frame usingthe same method asbefore.
Attach the beams to theend leg using the M6bolts provided.
Loosely thread the boltsinto the face of the legbefore threading thebolts to the underside ofthe leg.
Once all bolts arethreaded you can fullytighten them using the4mm Allen Key.
x 5
5
3
Step 3Insert the nylon inserts into the pre drilledholes on the underside of the desktop.
The illustration below shows which pre drilledholes should be used.
Repeat this step for all desktops.
x 4
If horizontal cable management is being added please refer to the
single cable tray assembly instruction before proceeding with the
next steps.
This will make the installation process much easier then trying to
install the cable trays once the desktops are attached.
6
5
Step 5Attach the desktop using the60mm connect bolts as shown.
Loosely thread all the bolts toensure that no bolts becomecross threaded before fullytightening.
4
Step 4Position the first desktop on theframe aligning the nylon insertswith the slotted holes .
x 4
COU800IL
Connex 800mm Intermediate Leg Frame
22.01.2017
1 2 3
1
This assembly instruction is to be used in
conjunction with COU800OL instruction.
1,2,3...
TO
OL
S R
EQ
UIR
ED
FO
R A
SS
EM
BL
YD
ON
T S
TR
UG
GL
E2
MA
N L
IFT
AL
WA
YS
HA
ND
LE
ITE
MS
WIT
H C
AR
EIF
UN
SU
RE
CA
LL
FO
R A
SS
IST
AN
CE
KE
EP
FIT
TIN
GS
AW
AY
FR
OM
CH
ILD
RE
N
2
Please check that you have all the Components!
3
1 2
3
800mm Intermediate Leg Frame Fixed Length Beam
1200 / 1400 / 1600mm
Desk Top
1200 / 1400 / 1600mm
Please check that you have all the Fittings! (Fittings supplied with leg frames)
1
800mm Intermediate Leg Frame
x 4
M6x60mm Connect Bolt
x 10
M6x10mm Countersunk Bolt
x 4
M6 Nylon Insert
4mm Allen Key
4
3
Step 3Attach the intermediate legframe using the same methodas before.
Attach the beams to the legusing the M6 bolts provided.
Loosely thread the bolts intothe face of the leg beforethreading the bolts to theunderside of the leg.
Once all bolts are threadedyou can fully tighten themusing the 4mm Allen Key.
This assembly instruction continues from the steps you have so
far completed from the ED800OL instruction sheet.
x 5
5
4
Step 4Attach the second beam to theintermediate leg using the M6bolts provided.
Loosely thread the bolts intothe face of the leg beforethreading the bolts to theunderside of the leg.
Once all bolts are threadedyou can fully tighten themusing the 4mm Allen Key.
x 5
6
If horizontal cable management is being added please refer to the
single cable tray assembly instruction before proceeding with the
next steps.
This will make the installation process much easier than trying to
install the cable trays once the desktops are attached.
5
Step 5Attach the remaining outer legframe using the same methodas before.
Attach the beams to the endleg using the M6 boltsprovided.
Loosely thread the bolts intothe face of the leg beforethreading the bolts to theunderside of the leg.
Once all bolts are threadedyou can fully tighten themusing the 4mm Allen Key.
x 10
7
6
Step 6Insert the nylon inserts into the pre drilledholes on the underside of the desktop.
The illustration below shows which pre drilledholes should be used.
Repeat this step for all desktops.
x 4
7
Step 7Position the first desktop on the framealigning the nylon inserts with the slottedholes .
8
Step 9Attach the desktop using the60mm connect bolts as shown.
Loosely thread all the bolts toensure that no bolts becomecross threaded before fullytightening.
Repeat this step for all remainingdesktops.
8
x 4
This assembly instruction illustrates how to assemble a 2 person configuration. For larger
configurations repeat steps 3 - 9 for each add on bay you would like to add.
2 Person
3 Person
4 Person