cost-effective rollover protective structure (crops)...2011/08/18 · crops technical drawings,...
TRANSCRIPT
Cost-effective Rollover Protective Structure (CROPS)
for Wheeled Agricultural Tractors
Massey Ferguson 135 SERIES
TECHNICAL DRAWINGS
Note: “Left” and “Right” refer to the tractor operators’ left or right as they sit in the seat looking forward.
DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention National Institute for Occupational Safety and Health
Massey Ferguson 135 Page 1
This document is in the public domain and may be freely copied or reprinted.
Disclaimer Mention of any company or product does not constitute endorsement by the National Institute for Occupational Safety and Health (NIOSH). In addition, citations to Web sites external to NIOSH do not constitute NIOSH endorsement of the sponsoring organizations or their programs or products. Furthermore, NIOSH is not responsible for the content of these Web sites. All Web addresses referenced in this document were accessible as of the publication date.
Ordering InformationTo receive documents or other information about occupational safety and health topics, contact NIOSH at
Telephone: 1–800–CDC–INFO (1–800–�3�–4636) TTY: 1–888–�3�–6348 E-mail: [email protected]
or visit the NIOSH Web site at www.cdc.gov/niosh.
For a monthly update on news at NIOSH, subscribe to NIOSH eNews by visiting www.cdc.gov/niosh/eNews.
Massey Ferguson 135 Page �
CROPS Technical Drawings, Massey Ferguson 135 Series
Part #11 (Backside) MF 135 Parts
Part #8
Part #9 Part #10
Driver’s Driver’s Left Side Right Side
Part #6L Part #6R
Part #2 Part #4 Part #7
Masssey Ferguson 135 Page 3
Part #12
Part #5
Part #1 Part #3
CROPS Technical Drawings, Massey Ferguson 135 Series
MF 135 3/4 - 16 x 7.5" (B4, W2, N2) Fasteners
3/4 -16 x 5" B3, W2, N2 Driver's
Left Side
5/8 - 18 x 1.75" (B1, W1, N1)
5/8 -18 x 1.25" (B5, W1)
3/4 - 16 x 4" (B2, W3, W2, N2)
5/8 - 18 x 7.5" (B7, W4, W1, N1)
3/4 - 16 x 7.5" (B4, W2, N2)
3/4 - 16 x 4" (B2, W2, N2) 3/4 -16 x 5"
(B3, W2, N2)
Driver's Right Side
5/8 - 18 x 1.75" (B1, W1, N1)
5/8 - 18 x 7.5" (B7, W4, W1, N1)
5/8 -18 x 1.25" (B5, W1)
3/4 - 16 x 4"3/4 - 16 x 4" 3/4 - 16 x 4" (B2,W2,N2) (B2, W3, W2, N2) (B2, W2, N2)
Masssey Ferguson 135 Page 4
2.500
CROPS Technical Drawings, Massey Ferguson 135 Series
MF 135 Part #1 Top Right Axle Bracket
Rev 8/18/2011 EAM
3/4 THRU
3/4 THRU
2.125 12.00
14.00
2.750 1.406
13/16
1.8125
2.344
5/8-18 UNF - 2B
1.250
6.00
14.00
2.375
8.00
R13/32
0.500
4.875 0.71875
Units = Inches: A572-Grade 50 Plate (or A36 Min Yield of 50) Masssey Ferguson 135 Page 5
0.750
4.875
CROPS Technical Drawings, Massey Ferguson 135 Series
MF 135 Part #2 Bottom Right Axle Bracket
Rev 8/18/2011 EAM
1.250
6.00
14.00
4.875
4.875
0.500
3.250
4.125
1.750
8.000 3/4 THRU
3/4 THRU
1.750
2.375 2.50
8.00
2.875
6.000
0.875
13/16 THRU
Units = Inches: A572-Grade 50 Plate (or A36 Min Yield of 50) Masssey Ferguson 135 Page 6
4.125
0.71875
CROPS Technical Drawings, Massey Ferguson 135 Series
MF 135 Part #3
4.875
0.50
2.125
12.00
0.750
2.750 1.8125
13/16
2.344
1.7188
11.47
Top Left Axle BracketRev 8/18/2011 EAM
5/8-18 UNF - 2B
R13/32
8.00 12.75
14.00
3/4 THRU 3/4 THRU
4.750
1.250
2.500
2.375
Units = Inches: A572-Grade 50 Plate (or A36 Min Yield of 50) Masssey Ferguson 135 Page �
4.875
2.50
CROPS Technical Drawings, Massey Ferguson 135 Series
MF 135 Part #4
8.00
12.75 14.00
2.375
Bottom Left Axle Bracket Rev 8/18/2011 EAM
3/4 THRU
1.375 3/4 THRU
7.750
13/16 THRU
0.500
3.750
6.250
4.875
4.875
4.875 Units = Inches: A572-Grade 50 Plate (or A36 Min Yield of 50)
Masssey Ferguson 135 Page 8
0.875
CROPS Technical Drawings, Massey Ferguson 135 Series
MF 135 Part #5 Vertical Tube Bolted Brace
Rev 8/18/2011 EAM
14.00
2"x3/8" steel plate
11/16 THRU 11/16 THRU
1.00 13.00
14.00
1.00
2.00
Units = Inches: A572-Grade 50 Plate (or A36 Min Yield of 50)
Masssey Ferguson 135 Page �
0.375
CROPS Technical Drawings, Massey Ferguson 135 Series
MF 135 Part #6 Vertical Tube
Rev 8/18/2011 EAM
DETAIL A SCALE 1 / 4
DETAIL B SCALE 1 / 4
A
B
1.50
9.00
71.25
1.00 4.00
2"x3"x3/16" ASTM A500 tubing
13/16 THRU
13/16 THRU
13/16 THRU
13/16 THRU
1.00
1.50
2.00
Weld Part #12 at 12.125" from bottom edgeof Part 6 to the bottom edge of Part 12 with the flat portion toward the wheel of the tractor offset 3/8" toward the tractor.(See Part #6R and #6L Drawings)
Units = Inches: ASTM A500 Tubing
3.00 2.00
Masssey Ferguson 135 Page 10
CROPS Technical Drawings, Massey Ferguson 135 Series
Units = Inches: A
STM A
500 Tubing
DETAIL
C SCALE 1 /3
C
12.125
0.375
12.125
56.125
71.25
3.00
A(Continuous W
eld ) B ( See A)
No W
eld
No W
eld
Part #12 M
F 135 Part #6R
Right V
ertical TubeR
ev 8/18/2011 EAM
Masssey Ferguson 135 Page 11
CROPS Technical Drawings, Massey Ferguson 135 Series
B (See A) A (Continuous W
eld)
Part #12
12.125
DETAIL D
SCALE 1 /3
D
Units = Inches: A
STM A
500 Tubing
0.375
12.125
56.125
3.00
71.25
No W
eld
No W
eld
MF 135 Part #6L
Left V
ertical Tube R
ev 8/18/2011 EAM
Masssey Ferguson 135 Page 1�
3.00
CROPS Technical Drawings, Massey Ferguson 135 Series
MF 135 Part #7 Bottom Vertical Tube Backing Plate
Rev 8/18/2011 EAM
5.00
3" X 3/8" steel plate
13/16 THRU 1.00
4.00 5.00
1.500
13/16 THRU
Units = Inches: A572-Grade 50 Plate (or A36 Min Yield of 50)
Masssey Ferguson 135 Page 13
0.375
CROPS Technical Drawings, Massey Ferguson 135 Series
MF 135 Part #8 Cross Bar Backing Plate
1.00 9.00
10.00
1.50
13/16 THRU 13/16 THRU
0.375
Rev 8/18/2011 EAM
10.00
3.00
Units = Inches: A572-Grade 50 Plate (or A36 Min Yield of 50)
Masssey Ferguson 135 Page 14
CROPS Technical Drawings, Massey Ferguson 135 Series
3.00
MF 135 Part #9 Cross Bar
Rev 8/18/2011 EAM
2"x3"x3/16" ASTM A500 tubing
1.00 9.00
23.00 31.00 32.00
13/16 THRU
13/16 THRU 13/16 THRU 3.00
32.00
2.00
1.50 13/16 THRU
Units = Inches: ASTM A500 Tubing
Masssey Ferguson 135 Page 15
CROPS Technical Drawings, Massey Ferguson 135 Series
MF 135 Part #10 Corner Plate
Rev 8/18/2011 EAM
12.00
12.00
1.50
9.00 12.00
1.00
9.00
12.00
13/16 THRU
13/16 THRU
13/16 THRU
0.250
Units = Inches: A572-Grade 50 Plate (or A36 Min Yield of 50)
Masssey Ferguson 135 Page 16
CROPS Technical Drawings, Massey Ferguson 135 Series
MF 135 Part #11 Top Vertical Tube Backing Plate
Rev 8/18/2011 EAM
0.25
10.50
2.00
1.50 9.00
10.50
1.00
13/16 THRU 13/16 THRU
Units = Inches: A572-Grade 50 Plate (or A36 Min Yield of 50)
Masssey Ferguson 135 Page 1�
CROPS Technical Drawings, Massey Ferguson 135 Series
MF 135 Part #12 Vertical Tube Welded Brace
Rev 8/18/2011 EAM
1.25
3.00
0.375
2.24
112°
22°
0.89
3.00
1.25
1.875
0.1875
0.1875
0.750
0.375
0.375
0.375 0.375
1.25
1.50
1.75
Units = Inches: A572-Grade 50 Plate (or A36 Min Yield of 50)
Masssey Ferguson 135 Page 18
0.75
CROPS Technical Drawings, Massey Ferguson 135 Series
MF 135 Part #13 Seat Belt Bracket
Rev 8/18/2011 EAM
10.50 0.1250
4.235
0.75 0.750
0.875
0.375
0.406
1.219
1.50
0.50 THRU
0.50 THRU
0.75
0.75 0.75
4.0631
5.6881
1.50
0.125
Units = Inches: A572-Grade 50 Plate (or A36 Min Yield of 50)
Masssey Ferguson 135 Page 1�
Delivering on the Nation’s promise: Safety and health at work for all people through research and prevention
To receive documents or other information about occupational safety and health topics, contact NIOSH at
Telephone: 1-800-CDC-INFO (1-800-�3�-4636) TTY: 1-888-�3�-6348 E-mail: [email protected]
or visit the NIOSH Web site at www.cdc.gov/niosh.
For a monthly update on news at NIOSH, subscribe to NIOSH eNews by visiting www.cdc.gov/niosh/eNews.
Massey Ferguson 135 Page �0