corolla 2016 keyless entry toyota

of 12

Corolla 2016 Keyless Entry

ConflictsNote: Not for installation on vehicles equipped with factory keyless entry

Additional Items Required For Installation

Recommended Tools

Kit Contents

LegendHardware Bag Contents

Vehicle Service Parts (may be required for reassembly)

STOP: Damage to the vehicle may occur. Do not proceed until process has been complied with.OPERATOR SAFETY: Use caution to avoid risk of injury.CRITICAL PROCESS: Proceed with caution to ensure a quality installation. These points will be audited on a completed vehicle installation.TOOLS & EQUIPTMENT: This calls out the specific tools and equipment required for this process.REVISION MARK: This mark highlights a change in installation with respect to previous issue.SAFETY TORQUE: This mark indicates that torque is related to safety.

S

Item# Quantity Req. Description1 1 Control Module2 1 Main Harness3 1 Hardware Bag4 1 Valet Switch5 2 24" Cable Ties6 2 3 Button Transmitter7 1 Owner's Card

Item# Quantity Req. Description1 8 Red T-Taps2 2 Blue T-Taps3 8 Black T-Taps4 1 Yellow T-Tap5 1 2-1/4" x 2-1/4" Foam Pad6 6 8" Cable Ties

Item# Quantity Req. Description

Safety Tools

Special Tools

Installation ToolsPhillips Screwdriver Straight-Slot ScrewdriverRachet w/ Extension 10 mm SocketWire Cutters/Strippers Common PliersFlashlight Nylon Trim ToolTorque Wrench (48 in. lbs.)Needle Nose Pliers Wire CrimpersSpecial Chemicals

Item# Qty Description00016-00063 1 Control Module00016-34030-05 2 Keyless Entry Transmitter00016-32901-01 1 Main Installation Harness00016-30960-56 1 On/Off Toggle Control Switch00016-32901-02 1 Hardware Bag00016-35105-01 1 Headlight Extension Wire

SPECIAL NOTE:After TMS and Safety mandated preparatory steps have been taken, the installation sequence is the suggested method for completing the accessory installation. In some instances the suggested sequence is written for one associate to install and in others the sequence is given as part of a team accessory installation. Unless otherwise stated in the document, the associates may perform the installation steps in any order to make the installation as efficient as possible while maintaining consistent quality.

Part Number: 00016-32901 Accessory Code: KE1000

Toyota

Rev. L 03/07/2016

iustyfa

Text Box

Doc. 03.09.00 Business Partner: L95 PIO / DIO Rev. E 03/08/16

of 12


INSTALLATION PREPARATION

1. Familiarize yourself with the installation instructions.

2. Inspect kit components (Refer to kitcontents and hardware bag contents).

VEHICLE PREPARATION

Negative Battery

1. Remove the plastic nut, disengage the (1) clip and remove the LH kick panel. (Fig. 2c)

1. Disengage the (10) claws and remove the LH scuff plate. (Fig. 2b)

REMOVE THE DRIVER'S SIDE KICK PANEL:

REMOVE THE DRIVER'S SIDE SCUFF PLATE:

PREPARING FOR INSTALLATION

Fig. 2b

Fig. 2c

Fig. 2a

Fig. 2d

Screw

REMOVE THE LOWER INSTRUMENT FINISH PANEL (LH):

1. Pry off the far right blank knock out cover using the slot at the bottom of the knock out and remove the screw located behind. Use protective tape to avoid damage to the finish panel when prying. (Fig. 2d)

Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation o f this accessory should follow ap-proved guidelines to ensure a quality installation.These guidelines can be found in the "Accessory Installation Practices" document. This document covers such items as:• Vehicle Protection (use of covers and blan-kets, cleaning chemicals, etc.).• Safety (eye protection, re-checking torque procedure, etc.).• Vehicle Disassembly/Reassembly (panel re-moval, part storage, etc.).• Electrical Component Disassembly/Reassem-bly (battery disconnection,connector removal, etc.).

of 12

Corolla 2016 Keyless EntryPREPARING FOR INSTALLATION

REMOVE THE LOWER INSTRUMENT FINISH PANEL (LH); cont:

1. Disengage the (8) clips, and remove the lower instrument finish panel. Then disconnect any electrical connectors. Using needle-nose pliers, disengage harness clip and remove clip from panel. Remove panel from vehicle and set the panel aside where it will not be damaged. (Fig. 3a)

Fig. 3a

Fig. 3b

REMOVE THE LOWER STEERING COLUMN COVER:

1. Remove the (2) philips screws securing the steering column cover. Then disengage the claws and remove the lower half of the steering column cover. (Fig. 3b)

T-TAP INSTALLATIONWhen installing female T-Tap connectors, be sure the wire is located inside the wire channel of the female T-Tap connector before closing the connector over the wire with pliers. When possible, install T-Taps at least 1" away from connector.

Step A Step B Step C

Wire from main keyless harness

T-Tap

IMPORTANT! After installation, inspect and ensure that Keyless System Harnesses are clear of all HOT, SHARP or MOVING objects.

IMPORTANT! Care MUST be exercised when using the BLACK T-Taps. To avoid damage and broken wires, please note:• Ensure there is NO tension on the T-Tap connection when securing the harness. The wire should be

slack. • Excessive manipulation and/or stress on the wire connection could lead to wire breakage.• Center the wire in the metal insert, NOT the plastic side of the T-Tap. Misalignment of the wire

against the metal insert could lead to cutting the wire.• It is recommended to close close the T-Tap with your fingers (Step A above). After the T-Tap has been

closed with your fingers, applying light pressure with a set of pliers will complete the connection.

of 12

Corolla 2016 Keyless EntryW

IRIN

G D

IAG

RA

M WIRING DIAGRAM - Corolla Keyless Entry

PIN

K / W

HIT

E W

IRE

[ LF

Doo

r Unl

ock

Switc

h ]:

Use

bla

ck T

-Tap

and

con

nect

to th

e YE

LLO

W

WIR

E in

con

nect

or H

E1, l

ocat

ion

3.

PIN

K W

IRE

[ LF

Doo

r Loc

k Sw

itch

]: U

se b

lack

T-

Tap

and

conn

ect t

o th

e B

LUE

WIR

E in

con

-ne

ctor

HE1

, loc

atio

n 4.

PIN

K /

WH

ITE

WIR

E [

Unl

ock

Det

ect

]: U

se

blac

k T-

Tap

and

conn

ect t

o th

e YE

LLO

W W

IRE

in c

onne

ctor

HE2

, loc

atio

n 10

.

Main Control Module

10 AMP

RED

WIR

E [

+12

VDC

]:

Use

bl

ack

T-Ta

p an

d co

nnec

t to

th

e B

LUE

WIR

E in

con

nect

or

E4, l

ocat

ion

4.

YELL

OW

WIR

E [ A

cces

sory

]:

Use

bla

ck T

-Tap

and

con

nect

to

the

BLA

CK

WIR

E in

con

nec-

tor E

4, lo

catio

n 7.

BLACK WIRE- (18 GA.) GROUND:Connect to factory ground location in driv-ers kick panel.

GREEN/RED WIRE [ Horn ]: Use black T-Tap and connect to the LT. GREEN WIRE in connector E8, location 9.

WHITE WIRE [ Tail lights ]: Use black T-Tap and connect to the WHITE WIRE in connec-tor E10, location 18.

BLUE WIRE [ Headlights]: Use black T-Tap and connect to the RED WIRE in connector E10, location 17.

WH

ITE

WIR

E [ D

river

's D

oor U

nloc

k M

otor

]:

Tow

ards

Doo

r Lo

ck -

See

D

etai

l A

BLU

E/W

HIT

E W

IRE

[ D

river

's D

oor

Unl

ock

Mot

or ]:

Tow

ards

Bod

y EC

U

- See

Det

ail A

DETAIL "A" DRIVER'S DOOR UNLOCK CIRCUIT

Cut the BLACK WIRE in connector HE1, location1. Strip the insulation from both sides of thecut wire, and crimp the WHITE WIRE from thekeyless harness to the HARNESS side of the cutwire. Crimp the BLUE/WHITE WIRE from thekeyless harness to the CONNECTOR side of thecut wire.

HarnessWires

BLUE w/WHITE

Cut & StripExisting

WireWHITE To Toggle Control Switch

of 12

Corolla 2016 Keyless EntryCONNECTOR DETAILS - Corolla Keyless Entry

3. CONNECTOR E8 : HornLocation : Lower Steering Column Cover Area

1. CONNECTOR E4 : Ignition Switch Location : Steering Column

2. CONNECTOR E10 : Tail Lights / Head LightsLocation : Lower Steering Column Cover Area

BluePin 4

+12V BATT(7.5A AM2)

BlackPin 7

+12V ACC(5A AM1)

Lt. GreenPin 9

HORN

WhitePin 18

Tail Lights

KEYLESS CAR PIN T-TAP Red Blue 4 BlackYellow Black 7 Black

KEYLESS CAR PIN T-TAP Green/Red Lt. Green 9 Black

KEYLESS CAR PIN T-TAP White White 18 BlackBlue Red 17 Black

RedPin 17

Head Lights

STOPTHERE ARE 2 LT. GREEN WIRES IN CONNECTOR E8. ENSURE CONNECTION IS MADE TO THE LARGER LT. GREEN WIRE IN PIN 9, NOT THE SMALLER LT. GREEN WIRE IN PIN 13. DAMAGE TO THE MODULE WILL OCCUR IF CONNECTED TO THE WRONG WIRE!

All Connectors Show Terminal View

of 12

Corolla 2016 Keyless EntryCONNECTOR DETAILS - Corolla Keyless Entry

4. CONNECTOR HE1 : Door Locks Location : Driver's Kick Panel Area

5. CONNECTOR HE2 - Unlock Detect Location : Driver's Kick Panel Area

YellowPin 3

Unlock Switch

YellowPin 10

UNLOCK DETECT

KEYLESS CAR PIN T-TAP Pink Blue 4 BlackPink/White Yellow 3 BlackWhite Black 1 Lock SideBlue Black 1 ECU Side

KEYLESS CAR PIN T-TAP Pink/White Yellow 10 Black

BluePin 4

Lock Switch

BlackPin 1

Unlock Motor

All Connectors Show Terminal View

of 12


Mounting the Main Control Module :

1. Fully extend and lift the tilt and telescoping steering column. Route the main wiring harness to the control module. Use caution when rout-ing to avoid any hot, sharp, or moving objects. Route the main wiring harness BEHIND the factory harness to avoid the harness shorting against the dash brace, as pictured. (Fig. 10a)

2. Apply provided adhesive pad to the side of the control module. Using the adhesive pad, mount the control module to the factory dash brace (to the left of the steering column).

3. Secure the control module to the factory brace with 1 long wire tie. (Fig. 10b)

INSTALLING THE KEYLESS ENTRY SYSTEM

IMPORTANT ! Make sure that the brake pedal, accelerator pedal, and acceletor pedal linkages are free and clear of all security harnesses.

Fig. 10b

Control Module

Connecting the Security System Harness :SECURING MODULE GROUND:

1. Locate the factory ground lug in the driver's kick panel area. Secure the black ground wire to the 10mm ground lug, Factory Ground point EA. Set Toggle Control Switch to OFF position. Secure excess wiring, Black ground wire, and the Toggle Control Switch to the factory wiring harness with a wire tie as pictured. (Fig. 10c)

Fig. 10c

Factory Ground Point EA Toggle Control Switch

Fig. 10aSharp Edge

EA

Factory Harness

SET Harness

of 12


COMPLETING THE INSTALLATION: COROLLA

TESTING THE SYSTEM:

1. Prior to delivering the vehicle, test all features of the system accordinng to the owner's manual included.

LOCK - Press and release the LOCK but-ton on the transmitter. All doors should lock, headlights should come on.

UNLOCK - Press and release the UN-LOCK button on the transmitter. The driver's door should unlock, headlights should come on.

Press and release the UNLOCK button again. All doors should unlock.

Press and hold the PANIC button for ap-proximately 3 seconds. The horn should sound and the parkings lights should flash.

Press and release the PANIC button to silence the horn.

NOTE: Be sure to test both transmitters that were included in the kit.

ASSEMBLE ALL REMOVED PANELS TO THE VEHICLE:

1. Refer again to the vehicle repair man-ual and reassemble all panels that were removed for installation back onto the vehicle. Test thoroughly, all mechani-cal components disconnected and or removed from the vehicle during the installation of this accessory.

PREPARING THE VEHICLE FOR DELIVERY:1. To set the arm/disarm chirps to "soft" chirps.

2. Start with the doors in the unlocked posi-tion, Toggle Control Switch in the "OFF" position.

3. Turn the ignition key to the on position.

4. Turn the ignition key off, then imme-diately switch the Toggle Control Switch "ON" then "OFF" 4 times.

5. The vehicle horn should respond with soft horn chirps.

6. Place owner's card in glove compartment.

NOTE : Re-torque battery cable to 48in lb. once process is completed.

Negative Battery

Verify that the DC CUT 30A FUSE is installed prior to testing.

S

of 12

Corolla 2016 Keyless EntryPROGRAMMING NEW or REPLACEMENT TRANSMITTERS TO THE SECURITY MODULE:

The programming mode will automatically terminate after 30 seconds of inactivity. This will be confirmed by the horn sounding a SHORT-SHORT-LONG pattern. If this happens, start over at step 1 to program transmitters.

STEP 2

IMPORTANT NOTE : Once you enter the programming mode, if 30 seconds elapse with no activity on the system, the programming mode will be terminated. If this happens, simply start over.

STEP 1

Turn the vehicle’s ignition key ON then OFF 7 times at 1 second intervals.....

....Ending in the OFF position.

The vehicle will respond by sounding the horn in a SHORT-LONG pattern to confirm you have entered programming mode.

To get started, disarm the mod-ule by first locating the silver toggle switch in the driver’s kick panel.

1. Insert the key into the ignition key cylinder and turn to the ON position

3. Flip the toggle switch ON, then OFF.

4. Turn the ignition key to the OFF position

STEP 3Press the Lock button on the transmitter. The horn will chirp to confirm it has learned the transmitter.

STEP 4Repeat Step 3 for all transmitters that you need to program to operate the vehicle.

(Maximum of 4 transmitters per vehicle)

STEP 5When all transmitters have been programmed, turn the ignition key ON then OFF to exit the program mode.

The vehicle will respond by sounding the horn in a SHORT-SHORT-LONG pat-tern to confirm programming mode has been termindated.

1 Second

ON

ON

OFF

OFF

of 12


VEHICLE FUNCTION CHECKLISTTHESE POINTS MUST BE CHECKED TO ENSURE A QUALITY INSTALLATION

Head Light

High Beams

Turn Signal Lights

Tail Lights

Stop Lights

Backup Lights

Hazard Lights

Marker Lights

Dome/Courtesy Lights

Panel/Switch Illumination

Accessory Controls/Illumination (if equipped)

Rear Window Defogger (if equipped)Key Sensor Buzzer

Fog Lights (if equipped)

Day Time Running Lights (if equipped)Trunk/Tailgate/Bed Lights (if equipped)Glove Box Light (if equipped)

ABS Light (if equipped)

Rear Wiper/Washer (if equipped)Clock (if equipped)

Accessory Power Socket (if equipped)Starter

Audio/Video (if equipped)

Power Sliding Door (if equipped)

If the warning lights remains on, it may indicate a system malfunction.

Convenience Memory Settings (if equipped)

Heated Seats (if equipped)

Massage Seats (if equipped)

Power Side Mirrors (if equipped)

Side Mirror Defogger (if equipped)

Front Windshield Defogger (if equipped)

Navigation System (if equipped)

Rear Sunshade (if equipped)

Cruise Control Light (if equipped)

Steering Wheel Audio Control (if equipped)HVAC

Power Locks (if equipped)

Power Windows (if equipped)

Gauges

Front Wiper/Washer

Hood Latch Release

Passenger Air Bag Switch (if equipped)

Rollover Side Curtain Air Bag Switch (RSCA)

Horn

Seat Belt Warning Light

Air Bag Warning Light

Lamp Failure Sensor

Track/Skid Control Light (if equipped)




If the warning lights remains on, it may indicate a system malfunction.Tire Pressure Monitoring System (TPMS)Prior to TPMS activation and Pre-Delivery Service (PDS) of the vehicle the TPMS light will blink when IG is turned on. After TPMS activa-tion and PDS of the vehicle the TPMS light will illuminate for a few seconds and go off when IG is turned on.

of 12


Block Diagram Keyless Entry System:

Corolla: Kit P/N 00016-32901

Keyless Entry Control Module P/N 00016-00063

P-W

P-

W

C-1 14

B

B

Ground - Connect to Factory Ground Point EA, Driver’s

Kick Panel.

C-1 15

Y Y

Ignition - Connect to Black Wire

(Connector E4, Cavity 7)

C-1

R

R

+12v - Connect to Lt. Blue Wire

(Connector E4, Cavity 4)

C-1 23

L L

Headlights - Con-nect to Red wire (Connector E10,

Cavity 17)

C-1 11

W

W

13

Tail Lights - Con-nect to White Wire (Connector E10,

Cavity 18)

L

C-1 10

L

Horn - Connect to Lt. Green Wire (Connector E8,

Cavity 9)

C-1 5

P-W

P-

W

C-1 6

Door Unlock de-tect - Connect to

Yellow Wire (Connector HE2,

Cavity 10)

Door Unlock Switch - Connect

to Yellow Wire (Connector HE1,

Cavity 3)

P P

C-1 21

Door Lock Switch - Connect to Blue Wire (Connector HE1, Cavity 4)

L-W

L-

W

C-1 7

Driver’s Door Unlock Motor -

Connect to Black Wire (Connector HE1, Cavity 1)

W

W

C-1 8

10 A

C-1

O-W

9

Driver’s Door Unlock Motor -

Connect to Black Wire (Connector HE1, Cavity 1)

Factory wire is cut in half, refer to installation instructions for additional

details.

C-1 18

B-O

B

-O

C-1 17

GR

G

R

On/Off Toggle Control Switch

P/N: 00016-30960-56

of 12


Connector C-1: Keyless Entry Harness Connector Connector End View

Pin Wire Color Test Reference Proper Operation Wire Function 1 No Wire N/A N/A N/A 2 No Wire N/A N/A N/A 3 No Wire N/A N/A N/A 4 No Wire N/A N/A N/A

5 Pink/White Pin 5 to Ground. Approximately 12VDC at rest. Continuity to Ground (pulsed) when driver’s unlock switch is in

the UNLOCK position or if keyless UNLOCK function is active (2nd UNLOCK press).

Unlock All Doors

6 Pink/White Pin 6 to Ground. Approximately 12 VDC at rest. Continuity to Ground (pulsed) when driver’s unlock switch is in

the UNLOCK position or if keyless UNLOCK function is active (2nd UNLOCK press).

Unlock Detect

7 Blue/White Pin 7 to Ground. Approximately 0 VDC at rest. Approximately 12 VDC (pulsed) when driver’s unlock switch is

pressed. Driver’s Unlock Motor ECU Side

8 White Pin 8 to Ground Approximately 12 VDC (pulsed) when keyless UNLOCK func-

tion is activated (first UNLOCK press). Approximately 0 VDC at rest.

Driver’s Unlock Motor Motor Side

9 Orange/White Pin 9 to Ground. Always 12 VDC. Active Out

10 Green/Red Pin 10 to Ground. Approximately 12 VDC at rest. Continuity to Ground (pulsed) when horn pad is pressed /

honking. Horn Chirp / Panic

11 White Pin 11 to Ground. Approximately 12 VDC at rest. Continuity to Ground (pulsed) when keyless is active Continuity to Ground (solid) tail lights are switched to ON at

headlight switch. Tail Light Flash

12 No Wire N/A N/A N/A

13 Red Pin 13 to Ground. Approximately 12 VDC. Battery

14 Black Pin 14 to Ground. Always continuity less than 1 ohm. Ground

15 Yellow Pin 15 to Ground. Approximately 12 VDC when the key is turned to the ON/Run

position. Approximately 0 VDC when key is turned OFF.

Ignition


17 Gray Pin 17 to Pin 18. Continuity to Ground when programming switch is in the ON

position. No Continuity to Ground when programming switch is in the

OFF position. Programming Switch

18 Black/Orange Pin 18 to Pin 17. Always continuity to Ground. Programming Switch 19 No Wire N/A N/A N/A 20 No Wire N/A N/A N/A

21 Pink Pin 21 to Ground. Approximately 12 VDC at rest. Continuity to Ground when driver’s lock switch is in the LOCK

position or if keyless LOCK function is active. Lock


23 Blue Pin 23 to Ground.

Approximately 12 VDC at rest. Continuity to Ground for 30 seconds after LOCK or UNLOCK

operation performed on keyless system. Continuity to Ground when Head Light Hi-Beam FLASH is

Activated on the Headlight Switch.

Headlight


Checking the Harness Pinouts:

corolla 2016 keyless entry toyota

Documents