corel ventura - g868usa · operating instructions for the g 868 dishwasher to prevent accidents and...

Operating instructions

for the G 868dishwasher

To prevent accidents and reducethe risk of damaging the machine, öread the Operating Manual before installing or usingthe machine. M.-Nr. 04 873 611

ContentsGuide to the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5View of the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Important safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Instructions importantes sur la sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Before using for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Opening and closing the door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Child safety lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Water softener (Not available in US models.) . . . . . . . . . . . . . . . . . . . . . . . . . . 15Setting the water hardness level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Filling the salt reservoir. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Salt indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Bypassing the Salt indicator lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Adding rinse aid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Setting the dosage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Loading the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Loading examples.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Bottom basket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Upper basket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Cutlery basket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Utensil Insert for the Cutlery Basket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Cutlery tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Adjustable cup racks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Coffee bar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Adjusting the upper basket.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Items not suitable for dishwashers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Adding detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Choosing a program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Program chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Operating the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Turning on. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Changing programs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Turning off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Program sequence indication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Program interruption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Unloading the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Contents

3

Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Cleaning the filters in the wash cabinet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Cleaning the spray arms.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Cleaning the drain pump and non-return valve. . . . . . . . . . . . . . . . . . . . . . . . . . . 38Cleaning the water intake filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39Cleaning the wash cabinet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Cleaning the door and the door seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Cleaning the control panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Cleaning the door panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Checking the water level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41Increasing the water intake time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43After Sales Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Dishwasher installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60Plumbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Contents

4

Guide to the applianceMiele dishwashers are available in twoversions:

1. Integrated (“i”) dishwashers

“i”- dishwashers are designed for instal-lation under a continuous countertop.

The control panel with its accessoriesis included with the “i”- dishwasher in aseparate package for on-site installa-tion. The front is designed to accept acustom made panel, matching the exist-ing kitchen cabinets.

Installation directions can be found inthe Installation chapter.

2. “U” dishwashers

The built-under (“U”) dishwashers usethe integrated (“i”) dishwashers as thebasic machine.

By using a GDU decor kit the “i”dish-washer can be converted into a “U”model dishwasher.

GDU installation instructions are in-cluded in a separate pamphlet sup-plied with the decor kit.

Guide to the appliance

5

View of the machine

1. Upper spray arm (not visible)

2. Cutlery tray (if applicable)

3. Upper basket

4. Water feed tube for the middlespray arm

5. Middle spray arm

6. Water hardness selector

7. Lower spray arm

8. Four height adjustable levelling legs

9. Combination filter

10. Salt reservoir (if applicable)

11. Dual compartment detergent dispenser

12. Rinse aid reservoir (with dosage selector)

13. Data plate

Note: Cutlery and lower baskets not shown.


6

Control panel

14. Rinse aid indicator lamp

15. Door release

16. Child safety lock

17. Temperature selector

18. Program selector knob


7

IMPORTANT SAFETY INSTRUCTIONSWARNINGWhen using your dish-washer, follow all basicsafety precautions.

This appliance conforms toall uniform safety codes andregulations. To avoid injuryand machine damage, readthe operating instructionscarefully before using thedishwasher.

This dishwasher is designed forhousehold use only.The manufacturer cannot be heldresponsible for damage or injurycaused by improper use or foruses other than those for whichthe appliance is intended.

Repairs should only be performedby qualified personnel. Disconnect

the appliance from the power supplybefore servicing (pull out the plug orturn off the circuit breaker).

If not purchased specifically as a“Freestanding” model, only install

the dishwasher under a continuouscountertop which is secured to thecabinetry.

The dishwasher must be electri-cally grounded. Install the dish-

washer as per the included Installationinstructions.

Use only powder detergents andliquid rinse aids recommended for

dishwashers. Never use gels or liquiddetergents.

Do not use commercial or indus-trial grade detergents, as these

may cause adverse chemical reactionsand damage the machine. Use onlydetergents made for residential dish-washers.

Do not use your dishwasher unlessall enclosure panels are properly in

place.

Do not allow children to play in oron the dishwasher.

Keep all detergents and rinse aidsout of the reach of children.

Dishwasher detergents contain So-dium Silicate and Sodium Carbo-

nate. In case of eye contact, immediate-ly flush with water. Call a physician orpoison control.

Do not tamper with the controls.

8

IMPORTANT SAFETY INSTRUCTIONSWhen loading items to be washed:

– Load pointed items so that they are not likely to damage the door seal.– Load knives with the cutting edge

down to reduce the risk of injuries.

Do not wash plastic items unlessthey are labeled “dishwasher safe”

or the equivalent. For items not labeled,check the manufacturer’s recommenda-tions.

Do not abuse, sit, or stand on thedoor or dishracks of the dish-

washer.

Remove the front door and cut offthe power cord of the dishwasher

before removing it from service or dis-carding it. This will help protect child-ren from injury or accidentally lockingthemselves in.

Under certain conditions, hy-drogen gas may be produced in a

hot water system that has not beenused for two weeks or more.HYDROGEN GAS IS EXPLOSIVE. If thehot water system has not been used forsuch a period, turn on all hot waterfaucets and let the water flow fromeach for several minutes before usingthe dishwasher. This will release any ac-cumulated hydrogen gas. Do notsmoke or use an open flame during thistime.

Do not drink the water from thewash cabinet.

For dishwashers with visible heating element

Do not touch the heating elementduring or immediately after use.

SAVE THESE INSTRUCTIONS

9

INSTRUCTIONS IMPORTANTES SUR LA SÉCURITÉ

AVERTISSEMENT

Au moment d’utiliser votre lave-vais-selle, veuillez observer toutes les me-sures de sécurité de base.

Cet appareil électroménager est con-forme à tous les règlements et codessur la sécurité. Pour éviter de vousblesser et d’endommager l’appareil,veuillez lire soigneusement les in-structions sur l’utilisation.

N’utilisez le lave-vaiselle que pourlaver la vaiselle.Le fabricant ne peut être tenu re-sponsable des dommages ou bless-ures causés par une utilisationinadéquate ou par des utilisationsautres que celles auxquelles l’ap-pareil est destiné.

Les réparations doivent être effec-tuées uniquement par une per-

sonne compétente. Débrancher l’ap-pareil de la prise de courant avant d’enfaire l’entretien (enlever la fiche de laprise ou fermer le disjoncteur).

Installer uniquement le lave-vais-selle sous un comptoir continu qui

est fixé à des meubles adjacents.

Vous devez mettre le lave-vaisselleà la terre. Installer le lave-vaisselle

en observant les instructions pour l’in-stallation ci-jointes.

Utiliser uniquement des détersifs etdes produits de rinçage recom-

mandés pour les lave-vaisselle.

Ne pas utiliser de détersifs dequalité commerciale ou industrielle

puisqu’ils pourraient causer des réac-tions chimiques défavorables et en-dommager l’appareil. Utiliser des déter-sifs pour les lave-vaisselle ménagersseulement.

Ne pas utiliser votre lave-vaisselleà moins que tous les panneaux

soient bien en place.

Ne pas permettre aux enfants dejouer dans ou sur le lave-vaisselle.

Ranger tous les détersifs et pro-duits de rinçage hors de la portée

des enfants.

Les détersifs pour lave-vaissellecontiennent du silicate de soude et

du carbonate de soude. En cas de con-tact avec les yeux, les rincer immédi-atement à grande eau. Téléphoner àun médecin ou à un centre de traite-ment antipoison.

10

INSTRUCTIONS IMPORTANTES SUR LA SÉCURITÉ

Ne pas modifier les commandes.

Ne pas boire l’eau du meuble delavage.

Au moment de remplir le lave-vais-selle :

– Mettre les articles pointus de manièreà ce qu’ils n’endommagent pas le seauétanche de la porte.– Mettre le tranchant des couteaux versle bas afin de réduire les risques deblessure.

Ne pas laver les articles en plas-tique à moins qu’ils n’indiquent “Va

au lave-vaisselle” ou l’équivalent. Véri-fier les recommandations du fabricantpour les articles non étiquetés.

Ne pas abuser et ne pas vous as-seoir ni vous tenir sur la porte ou

sur les paniers du lave-vaisselle.

Enlever la porte et débrancher lelave-vaisselle avant de le faire rép-

arer ou de le jeter afin d’empêcher lesenfants de se blesser ou de s’enfermerdans l’appareil par accident.

Dans certaines conditions, un sys-tème d’eau chaude qui n’a pas été

utilisé pendant plus de 2 semainespeut dégager de l’azote.L’AZOTE EST EXPLOSIF. Si le systèmed’eau chaude n’a pas été utilisé pend-ant une telle période de temps, ouvrirtous les robinets d’eau chaude etlaisser l’eau couler pendant plusieursminutes avant d’utiliser le lave-vais-selle. Ceci dissipera tout l’azote accu-mulé. Ne pas fumer ni utiliser uneflamme nue durant ce temps.

Lave-vaiselle avec l’élément chauffant

Ne touchez pas l’élément chauf-fant pendant le fonctionnement de

l’appareil ou immédiatement après.

CONSERVER CES INSTRUCTIONS

11

Caring for the environmentDisposal of the packing material.

The cardboard box and packing ma-terial protects the appliance duringshipping. It has been deliberately de-signed to be biodegradable and recy-clable. Please dispose of these ma-terials as you would any otherrecyclable products.

Disposal of your old machine.

Old machines contain materials whichcan be recycled. Please contact yourlocal recycling center about the possi-bility of recycling these materials. Makecertain the machine has been madechild resistant as outlined in the “Import-ant safety instuctions” before disposingof the appliance.

Energy saving washing.

These dishwashers are exceptionally ef-ficient in their use of water and elec-tricity. You can make the most of yourappliance by following these tips:

Make full use of the baskets withoutoverloading the dishwasher for themost economical washing.

Choose a program that best suits thedegree of soiling and the type ofdishes being washed.

If the baskets are only half full, usethe ECONOMY program.

Use the correct amounts of deter-gent and rinse aid.

Caring for the environment

12

Before using for the first timeBefore using for the first time,please note the following points.

Setting the water softener(if applicable).

The water softener must be set to corre-spond to the water hardness in yourarea. This can be obtained from yourlocal water company, or by using a testkit that can be purchased from theMiele Parts Department.

The salt reservoir must only be filledwith water and salt. Never fill it withdetergent.

Adding rinse aid.

Inadvertently filling the rinse aidreservoir with liquid or powder deter-gent will damage the reservoir.

Use only powder detergents and liquidrinse aids formulated for domestic dish-washers.

It is important to choose the correctprogram.

Different wash programs should be se-lected for different loads and differentdegrees of soiling. See the programchart for further program descriptions.

Add the correct amount of detergent.

Generally, one to two tablespoons ofdetergent will be adequate for mostwash loads. Not enough or too muchdetergent can lead to poor wash re-sults.

Cleaning results vary between deter-gents. If you are not satisfied with theresults from one brand, try anotherquality brand before contacting theMiele Service Department for advice.

Load the dishes correctly.

Load the dishes so that water can con-tact all surfaces. Ensure that the sprayarms are not blocked by items whichare too tall for the basket or which ex-tend through the bottom of the basket.If necessary, manually rotate the sprayarms to test for clearance.

The combination filter in the base ofthe wash cabinet and the spray armsmust be kept clean.

These should be regularly inspectedand cleaned, if necessary.

See the corresponding chapters for de-tailed information on the above points.

Before using for the first time

13

Opening and closing the doorTo open the door.

Press the release catch inside thedoor grip.

If the door is opened during operation,all functions will automatically be inter-rupted.

To close the door.Push the baskets in.

Lift the door and push until it clicksinto position.

Child safety lock.

The child safety lock is designed todeter children from opening the dish-washer door.

Use the provided key to turn thechild safety lock to the desired set-ting.

Horizontal setting = The door islocked.

Vertical setting = the door canbe opened.

Opening and closing the door

14

Water softener (Not available in US models.)The water softener must be set to corre-spond to the water hardness in yourarea. This can be obtained from yourlocal water company or by using a testkit that can be purchased from theMiele Parts Department.

Note:

If the water hardness in your area isunder 7 gr/gal, it is not necessary to re-activate the softener with salt.

To avoid the build up of calcium de-posits on dishes, cutlery, and in thedishwasher, the water should be soft-ened if it is harder than 7 gr/gal.

The dishwasher is factory set for a hard-ness level of 4 - 14 gr/gal. If your wateris harder or softer, this setting will needto be adjusted.

To ensure a steady supply of soft-ened water, the built in water sof-tener must be:

1. Correctly set.

2. Reactivated with salt when depleted.

Setting the water hardnesslevel.There are six settings on the selector, lo-cated on the right side of the washcabinet:

Using a screwdriver, adjust the waterhardness level by turning the selec-tor switch to the appropriate setting.

Setting gr/gal ppm °f

1* 4-14 70- 250 7- 25

2 15-21 270- 380 27- 38

3 22-35 400- 630 40- 63

4 36-47 650- 850 65- 85

5 48-65 860-1170 86-117

6 66-70 1190-1260 119-126

*) factory setting

Example:

The water hardness is 340 ppm. Thewater hardness switch should be set toposition 2.

Water softener (Not available in US models.)

15

Filling the salt reservoir.The salt reservoir should be filled be-fore the first use and whenever the“Salt” indicator lamp is lit. Use watersoftener reactivation salt (1 - 4 mmgrain size), as other salts may containinsoluble additives which can impairthe functioning of the softener.

The salt reservoir holds approx. 4 lbs (2 kg) of salt.

Inadvertently filling the salt reservoirwith dishwashing detergent willdamage the water softener. Makesure that only water softener reacti-vation salt of the proper grain size isused.

Remove the lower basket.

Unscrew and remove the salt reser-voir cap.

Before filling the salt reservoir forthe first time:Fill the salt reservoir with approxi-mately 2 quarts of water.

Place the funnel (provided) over thesalt reservoir.

Carefully fill with salt. As it is filled,water will run out.

Clean any excess salt from thethreads of the reservoir opening.

Screw the cap on firmly.

If the dishwasher will not be used im-mediately after reactivation, run theRINSE & HOLD program. This willremove any traces of salt from thecabinet.


16

Salt indicator.

When the salt reservoir is empty, the“Salt” indicator lamp will light, notifyingyou that the reservoir should be refilledwith reactivation salt.

Note:

If your water is very soft (below 7 gr/gal), the salt indicator lamp willstay on. In this case the reservoirshould not be filled with salt. The indica-tor lamp will remain lit and can be disre-garded or bypassed.

Bypassing the Salt indicatorlamp.In order to bypass the salt indicatorlamp, you will need a screwdriver andneedle nose pliers.

Remove the salt reservoir cap.

Looking into the salt reservoir, you willsee the top of the float chamber on theright hand side b.

Using a screwdriver, carefully pivotthe float chamber towards the centerof the reservoir.

Using the needle nose pliers, firstpull the cap c off of the float cham-ber, then remove the float d.

Replace the float chamber cap,push the chamber back into its up-right position, and replace the saltreservoir cap. The indicator lampshould now remain off.


17

Adding rinse aidThe use of Rinse Aid is recommendedto prevent spotting on dishes and glass-ware that normally occurs during thedrying phase of automatic dishwashing.

Inadvertently filling the rinse aidreservoir with detergent will alwaysdamage the reservoir. Only pour liq-uid rinse aid formulated for residen-tial dishwashers into the reservoir.

Adding rinse aid.

Add Rinse Aid before the first useand anytime the “Rinse Aid” indica-tor lamp comes on.

Press the button in the direction ofthe arrow until the flap springs open.

Adding rinse aid

18

Pour liquid rinse aid into the storagecontainer until it is visible on the sur-face of the screen. Do not refill untilthe “Rinse aid” indicator lamp comeson.

Only use rinse aid specificallylabeled for residential dishwashers.Inadvertently adding detergent willdamage the rinse aid dispenser.

Press on the flap until you hear itclick shut. Failure to close it all theway will allow water to enter thereservoir during the wash program.

Wipe up any spilled rinse aid.

The flap will remain closed during nor-mal operation.

Setting the dosage.

The dosage selector comes factory setto 3. It can be adjusted from 1 to 6, de-pending on your requirements. This set-ting dispenses approximately 3 mlrinse aid per program.

Use a higher setting if spots appearon dry glassware.

If streaking appears on dishes orglasses, use a lower setting.

Adding rinse aid

19

Loading the dishwasherLoad the dishes so that water canreach all surfaces.

Do not place dishes and cutlery in-side other pieces where they may beconcealed.

Hollow items such as cups andglasses should be inverted andplaced in the upper basket.

Concave based items should beplaced at an angle so that water canrun off them freely, or placed on topof the coffee bar (See page 25).

Tall, narrow, hollow pieces should beplaced in the center of the basket,rather than in the corners, to ensureadequate water coverage.

Small cups and glasses should beplaced on the cup racks. Taller mugsand glasses can be placed under-neath the rack.

The spray arms must not be blockedby items which are too tall or hangthrough the baskets. If in doubt, testfor free movement by manually rotat-ing the spray arms.

Some food items may contain naturaldyes that can discolor plastic itemsin the dishwasher ( e.g. carrots, to-matoes, ketchup, etc.). The stabilityof plastic items is not affected by thisdiscoloration.

Some loading examples are shown onthe following pages.

In areas where the water has highmineral content, it may be necess-ary to polish silverware after wash-ing to achieve a high shine.

Loading the dishwasher

20

Loading examples.

Bottom basket.

For larger and heavier items such asplates, serving platters, saucepans,and bowls. Depending on the dish-washer model, glasses can be cleanedin the bottom basket if a special glass-ware insert is installed.

Dishwashers with cutlery tray.

Dishwashers with cutlery basket.

Height limit

The height guard at the base of theupper basket is there to protect themiddle spray arm. No object placed inthe lower basket should stand higherthan this guard.

Upper basket.

For small, lightweight, delicate itemssuch as cups, saucers, glasses, des-sert bowls, etc.


21

Cutlery

Dishwashers with cutlery basket:

Unsorted cutlery should be placed inthe cutlery basket, with the sharp endsdown.

Place small spoons in the individualslots to either side of the cutlery basket.

Larger items like soup ladles, longknives and mixing spoons should beplaced lying down across the front ofthe upper basket.


22

Utensil Insert for the Cutlery Basket

By ensuring that one piece of cutlerydoes not rest against another, the in-cluded Utensil Insert will optimize thecleaning of soiled spoons and forks.

To use the inserts:Place one in front of and one behindthe basket handle by pushing themdown over the notches on the basketpartition walls.

To remove the inserts:Press in the latching tabs, using aspoon handle if necessary, andremove the inserts from the basket.

Place the utensil handles into the in-serts, making sure that adjacentitems do not touch.


23

Dishwasher with cutlery tray.

To make unloading easier, cutlery canbe grouped in zones, one for knives,one for forks, etc.

Larger items like sauce ladles, cakeslices, long knives and mixing spoonscan be placed lengthwise in the troughin the center of the tray.

Make sure that the upper spray armcan rotate freely after the tray is slidin, otherwise the rotation of thespray arm may be inadequate for athorough cleaning.

The cutlery tray insert is removable.

Spoon heads should be placed so thatwater can run off them freely.

Place the heads of cutlery with roundor oval handles in the holders. This willsecure them during the wash cycle.

Place spoons so that their heads are se-cured in at least one holder so they can-not flip over and collect water.


24

Adjustable cup racks.

To make room for tall glasses, raise therack. Lower it to double stack smalleritems.

Coffee bar.

To allow water to run off of the bottomof coffee mugs, place them at a slanton top of the coffee bar. The bar can also be used as a separ-ator between two rows of glasses toprotect them and keep them from lean-ing against each other. To stack wideitems, flip the bar to the right.


25

Adjusting the upper basket.(depending on model)

The upper basket height is adjustable.If tall items of dishware are beingwashed, more room can be obtainedby raising or lowering the upper basket.

Pull out the upper basket and loosenthe two locknuts on either side of thebasket.

Adjust the basket up or down to thedesired height.

Tighten the locknuts.

The upper basket can also be set at anangle with one side high and the otherside low.

Depending on the setting of the upperbasket, the following dishware dimen-sions can be accommodated:

Dishwashers with cutlery tray

Upper basket position

Upper basket

diameter

Lowerbasket

diameterTop 8"

(20.5 cm)12"

(30 cm)Middle 9"

(22.5 cm)11"

(28 cm)Bottom 10"

(24.5 cm)10 1/2"(26 cm)

Dishwashers with cutlery basket(non-adjustable upper basket)

Upper basket diameter 11"

Lower basket diameter 11"


26

Items not suitable for dishwashers– Cutlery with wooden handles.

– Wooden cutting boards.

– Glued items such as old knives withhandles that are glued togetheraround the shank of the blade.

– Hand made craft items.

– Copper or tin items.

– Plastic items which are not heat resis-tant.

Please note:

– Silver or aluminum items may suffersome discoloration.

– Aluminum parts (eg. oven hoodgrease filters) should not be cleanedusing commercial or industrial deter-gents. These high alkaline deter-gents may damage the machine,and in extreme instances, cause ex-plosive chemical reactions.

– Silverware previously cleaned with asilver polish may be damp orspotted at the end of a programwhere water has adhered to the pol-ish. This can be rubbed off with asoft, dry cloth. Silver that has pre-viously been cleaned in an immer-sion dip is usually dry at the end of aprogram, but may discolor (tarnish).

– Colors on dishware that have beenpainted over the glaze may fadeover time.

– Clouding may occur on glasses afterfrequent washing.

Miele recommends:

Wash delicate glassware using theECONOMY program or the CHINA &CRYSTAL program with a tempera-ture of 45 °C/115 °F (if so equipped).This will reduce the risk of clouding.

There are no standard guidelines forwashing glassware. When in doubt,wash by hand.

When purchasing new dishes andcutlery, make sure they are dish-washer safe.

Items not suitable for dishwashers

27

Adding detergentUse only powder detergents formu-lated for residential dishwashers.Do not use gels or liquid deter-gents.

Press the latch on the detergent dis-penser. The cover will spring open.

Fill the dispenser with one to twotablespoons of powder detergent.

Close the cover. The cover will al-ways be open at the end of a washprogram (excluding the RINSE &HOLD program).

Generally, filling the dispenser with oneto two tablespoons of detergent will besufficient to ensure thorough cleaning.If dishes are extra dirty, or if the soil hasbeen allowed to dry on the dishes be-fore washing, a program utilizing a pre-wash cycle should be selected. In thiscase, extra detergent can be added tothe small compartment labeled ( I ) inthe center of the dispenser.

Dishwasher detergents contain irri-tant and corrosive ingredients. Theycan cause burns in the mouth andthroat if swallowed, or inhibit brea-thing. Keep children away fromdetergent and from the dishwasherwhen the door is open.

To avoid the danger of children com-ing into contact with dishwasherdetergent, only fill the detergent dis-penser immediately before startingthe program.

Capacities:Compartment I (prewash) takes a maxi-mum of 1 ounce (25 ml) and Compart-ment II (main wash) takes a maximumof 3 ounces (80 ml) when completelyfilled. There are horizontal marks to as-sist you in filling Compartment II. Themarks indicate a level of approximately3/4, 1, and 1 1/4 ounces (20, 25 and30 ml respectively).

Adding detergent

28

Choosing a programThe wash program chosen should de-pend on the type of dishes and the de-gree of soiling.

In most cases a NORMAL program willgive excellent results.

The available programs and some oftheir applications are listed in the Pro-gram Chart on the next two pages.

Choosing a program

29

Program chartProgram When to use Detergent

containingchlorine 1)

chlorinefree2)

Compart-ment

I(Pre-wash)

Compart-ment

II(Washcycle)

Compart-ment

II(Washcycle)

ProgramNORMAL55 °C/130 °F

This program is for normal everyday loads. 20 % 80% 100 %

NORMAL65 °C/150 °F

Same as NORMAL 55 °C/130 °F, but at ahigher temperature. Use for stubborndried on particles .

20 % 80 % 100 %

INTENSIVE55 °C/130 °F

Contains an additional pre-wash cycle.Use for heavily soiled dishes.

20 % 80 % 100 %

INTENSIVE65 °C/150 °F

Same as INTENSIVE 55 °C/130 °F, but at ahigher temperature. Use for stubborn driedon particles and lightly soiled pots andpans.

20 % 80 % 100 %

Special programsECONOMY 55 °C/130 °F

For a half sized load, or for a full load withvery light soiling (e.g. coffee cups). 50 % 3) 50 % 3)

RINSE & HOLD For rinsing dishes if a complete program isnot yet needed.

The dispensing method will depend on the type of detergent being used: 1) Use this ratio for:

– detergents which contain phosphates and chlorineDivide the total amount, as shown, between compartment I and compartment II.

2) Use this ratio for:– detergent which is chlorine and phosphate free – detergent which is chlorine free but contains phosphatesIn this instance the whole amount is placed in compartment II.

3) Use half of your normal amount of detergent.

For the NORMAL and INTENSIVE programs, one to two tablespoons of detergent is usually sufficientfor excellent wash results.

Program chart

30

Program cycle Usage DurationElectric (kWh)

Water

1.Preliminarypre-wash

2.Pre-wash Main

washInterimrinse

Final rinse DryingHot waterconnec-

tion(49 °C /120 °F)

Liters/Gallons 4)

Minutes (approx.)

X X X X X 0.9 19.6 / 5.2 104

X X X X X 1.2 19.6 / 5.2 109

X X X X X X 0.9 24.5 / 6.5 109

X X X X X X 1.0 24.5 / 6.5 110

X X X X 0.8 5) 14.7 / 3.9 83 5)

X 0.06 5 / 1.3 8

4) For models without water softener5) With half loads (Dishwasher with cutlery tray – 6 place settings

dishwasherwith cutlery basket – 7 place settings)X = cycle being used

Program chart

31

Operating the dishwasherTurning on.

Close the door.

Open the water valve (if closed).

Turn the Program knob clockwise tothe desired program.

Select the desired temperature, orthe "RINSE & HOLD” program.

The wash program will begin.

If you turn the Program knob pastyour desired program by mistake:

Turn the Temperature selector to“OFF”.

Turn the program knob clockwisepast the 12 o’clock position, until thedesired program is reached.

Select the temperature.The new program will start.

Changing programs.Wash temperatures can be changedwhile a program is running, by turn-ing the Temperature selector.

If a different wash program isdesired, follow the above procedure.

Turning off.When finished, the program will stopautomatically.

Your Miele dishwasher is designed toshut off the water flow and drain themachine in the rare event of a valvefailure. In order for this function to beactive, the door must be shut, a tem-perature must be selected, and theprogram knob must be in the “End”(12 o’clock) position.

Operating the dishwasher

32

Program sequence indication.During the wash program, the programknob will move around the dial andshow which section of the wash cyclehas been reached.

– Pre-wash (not shown)

– Main wash

– Interim rinse

– Final rinse

– Drying

The dial will remain stationary duringthe heating stages of the wash andrinse cycles, until the required tempera-tures have been reached.

When the program has been com-pleted, the dial will be in the “End” posi-tion.

The dishwasher can now be openedand unloaded. If the dishes are not im-mediately needed, leaving the doorclosed will allow the fan to run a fewminutes longer to remove any remain-ing moisture.

The “RINSE & HOLD” program hasbeen completed when the program dialstops just before the starting point ofthe “INTENSIVE” program.

Program interruptionA program is interrupted as soon as thedoor is opened. If the door is closedagain, the program will proceed fromits previous position.

WarningThe water in the dishwasher maybe hot, and steam may be present! Only open the door if absolutelynecessary and exercise extremecaution when doing so. The dangerof burns and scalding exists.Once the door has been opened,allow 20-30 seconds for the inter-nal temperature to equalize beforeclosing it again, and make sure itclicks into place.


33

Unloading the dishwasherDishes tend to break and chip easierwhen they are hot. Allow the dishesto cool down until they are comfor-table enough to handle before un-loading them.

If the door is opened at the end ofthe drying cycle, the dishes will coolmuch faster.

Unload the lower basket first, thenthe upper basket and cutlery tray (ifso equipped). This will prevent waterdrops from the upper basket or cut-lery tray from falling onto the dishesin the lower basket.


34

Cleaning and careCleaning the filters in thewash cabinet.

The combination filter in the base ofthe wash cabinet should be regu-larly inspected and cleaned asnecessary. Any broken glass ordishware should be removed imme-diately upon discovery. Use caution when cleaning the fil-ters, non-return valve or drainpump, as glass or bone splintersmay be caught in the bottom of thewash cabinet. Turn the handle counterclockwise to

release the filters.

Lift the combination filter out of themachine. Remove any coarse par-ticles and rinse it under runningwater. A nylon brush can be used, ifnecessary.

Cleaning and care

35

Turn the combination filter over andopen the coarse filter cover by pull-ing back on the locking tab.

After cleaning, make sure that thecoarse filter cover is properly lockedin place.

Replace the combination filter sothat it lies flat in the base of the washcabinet. Secure it by turning thehandle clockwise.

Cleaning and care

36

Cleaning the spray arms.On rare occasions particles of foodmay get stuck in the spray arm jets.They can be easily cleaned as follows:

To remove the middle spray arm lo-cated beneath the upper basket,gently push upwards until it engagesin the ratchet b, then unscrew it c.

Lift up on the lower spray arm toremove it.

Dishwashers with cutlery basket:

Unscrew the upper spray arm.

Dishwashers with cutlery tray:

Pull out the cutlery tray.

Push up on the upper spray arm toengage the tooth-wheel mechanismand then unscrew the spray arm.

To clean the spray arms, use apointed object to push the the foodparticles into the jets.

Rinse under running water to com-plete the process.

After cleaning, replace the sprayarms.

Important:After replacing the spray arms,check that they rotate freely.

Cleaning and care

37

Cleaning the drain pump andnon-return valve.

Use caution when cleaning the fil-ters, non-return valve or drainpump, as glass or bone splintersmay be caught in the bottom of thewash cabinet.

If the water in the dishwasher is notcompletely drained at the end of a pro-gram, the drain pump or non-returnvalve may be blocked. To clean them:

Remove the combination filter.

Use a jug or bowl to scoop the waterout of the wash cabinet.

Tilt the locking clamp to the side.

Pull out the non-return valve.

Rinse the non-return valve under run-ning water.

The drain pump is situated under thenon-return valve (see arrow).

Before replacing the non-return valve,check to make sure that nothing is ob-structing the drain pump. Spin the im-peller several times in both directions;it should turn smoothly.Carefully replace the non-returnvalve and secure it with the lockingclamp.Replace and secure the combinationfilter.

Cleaning and care

38

Cleaning the water intake filter.

The water valve housing on the inlethose contains electrical compo-nents and should not be immersed,or run through water.

A filter is incorporated in the intakehose that is attached to the dishwa-sher’s main shutoff valve. If your watersupply is hard, or the pipes containsediment; this filter may clog and pre-vent sufficient water from entering thewash cabinet. It can be cleaned as fol-lows:

Cleaning the filter.Disconnect the dishwasher from theelectrical supply (unplug it or shut offthe circuit breaker).

Turn off the main shutoff valve andunscrew the intake hose.

Carefully remove the rubber seal.

Remove the filter using needle nosepliers and clean it by rinsing underrunning water.

Replace the filter and seal. Makesure they are seated correctly.

Screw the intake hose back onto thewater valve, making certain it is notcross-threaded.

Slowly turn on the valve and test forleaks.

Installing an in-line water filter.

If your water supply contains a largenumber of insoluble substances, werecommend installing a filter betweenthe valve and the intake hose connec-tion. These filters can be obtainedfrom the Miele Parts Department.

Cleaning and care

39

Cleaning the wash cabinet.Generally the wash cabinet is self-cleaning, provided that the correctamount of dishwasher detergent isused.

If lime scale or grease deposits form,they can be removed with a specialdishwasher cleaner available from theMiele Parts Department.

Cleaning the door and thedoor seal.

Wipe the door seal with a dampcloth to remove any food particles.

Food residue and drink spillageshould be wiped from the sides ofthe dishwasher door. These areasare not normally cleaned by waterfrom the spray arms.

Cleaning the control panel.The control panel can be cleanedusing a damp cloth and mild deter-gent.

Do not use abrasive, all purpose, orglass cleaners, as their use maydamage plastic surfaces.

Cleaning the door panel.Plastic laminate panels should becleaned using a suitable, non-ab-rasive cleaning agent, or mild soapywater.

Panels made from wood should becleaned using a soft damp cloth andan appropriate wood cleaner.

Cleaning and care

40

Checking the water levelChecking the water level.If the water pressure is less than14.5 psi (1 bar), too little water mayflow into the wash cabinet.

To check the water level, open thewater valve completely and run theRINSE & HOLD program once (with-out dishes), to bring water into thesystem.

Start the RINSE & HOLD programagain. After approximately 3minutes, open the door and removethe lower basket from the machine. The water level is correct when dimen-

sion “X” is at least 1/8" (4 mm).

If it measures less, the water intaketime must be increased.

Checking the water level

41

Increasing the water intaketime.

Position the program knob verti-cally, then pull it off.

Using a small screwdriver, turn theadjusting slot on the right hand sideof the spindle carefully counterclock-wise until it clicks into position.

= Counterclockwise turn (increases water intake to 2 min.)

= Clockwise turn (factory setting - 1 min.)

Note:If the water intake time has been in-creased, the water hardness selectorshould be set one number higher thanthat stated in the “Water softener” chap-ter (if applicable).

Checking the water level

42

Problem solving guideWith the aid of the following notes,minor problems can be easily cor-rected. If you are unable to correct theproblem, please contact the Miele Ser-vice Department.

Any work on the electrical compo-nents of the appliance should onlybe performed by a qualified andtrained person in accordance withlocal and national regulations. Un-authorized repairs could be dan-gerous.

Problems and possible causes.

The dishwasher does not start.

– The door is not properly closed.

– The plug is not properly inserted.

– The circuit breaker has tripped.

The dishes are not clean.

– The dishes are loaded incorrectly.

– The wrong amount or type of deter-gent was used.

– The water pressure is too low (allow-ing too little water into the dish-washer). See “Checking the waterlevel”.

– The water intake filter is clogged.See “Cleaning and care”.

– The filters in the wash cabinet arenot clean. See “Cleaning and care”.

– The spray arm jets are blocked - see“Cleaning and care”.

– The spray arms are obstructed byitems in the baskets.

White residue is visible on cutleryand dishes.

– Not enough rinse aid was used.

– No salt in the salt reservoir.

– The salt reservoir lid has not beenscrewed on properly.

Water remains in the dishwasher atthe end of a program.

– The drain hose is kinked or clogged.

– The drain pump or non-return valvemay be blocked. See “Cleaning andcare”.

After Sales Service.Should you still have difficulties, or ifthe appliance is under warranty,please contact the Miele Service Department. (See back cover for address).

Please give the model and serialnumber of your appliance. This infor-mation can be found on the dataplate inside the door.

Problem solving guide

43

AccessoriesBottle holder.(depending on model)

A bottle holder (for milk or baby bottles)is available for use in the lower basket.

To achieve the proper cleaning results,the bottle holder should only be placedin the basket as shown in the illustra-tion.

Glass insert for the upper basket:provides special support for longstemmed glassware.

Decor panel kit (GDU):to change an “i” model into a “u” modeldishwasher.

Side mount brackets:For installing a dishwasher under Co-rian® or granite countertops.

These and other accessories are avail-able through your Dealer or the MieleParts Department.

Accessories

44

Installation instructions

45

ContentsDishwasher installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 471. Installing the steam deflector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 472. Installing the dishwasher under the countertop. . . . . . . . . . . . . . . . . . . . . . . . . 483. Installing the control panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 504. Aligning the control panel with the drawer fronts. . . . . . . . . . . . . . . . . . . . . . . . 515. Installing the custom door panel.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 516. Adjusting the door springs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 557. Securing the dishwasher to the countertop. . . . . . . . . . . . . . . . . . . . . . . . . . . . 558. Installing the toekick. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60Plumbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Contents

46

Dishwasher installationThe “i” model dishwasher is speciallydesigned for installation under a con-tinuous countertop.

A panel can be custom made for instal-lation on the front of the dishwasher, as-suring a perfect match with the kitchencabinetry.

If a standard non-cabinet matchingdishwasher installation is desired, the“i” model dishwasher can be convertedinto a “U” model through the addition ofa GDU 60/65 decor kit. The decor kitcomes supplied with separate installa-tion instructions.

To ensure stability, these dish-washers should only be installedunder a continuous countertopwhich is securely fastened to thecabinet base units.

Dimensions:

1) with 35" (890 mm) machine height2) with 33 1/8" (840 mm) machine height

Range of adjustment is approximately2" (5 cm).

1. Installing the steam deflector, (if applicable).

A stainless steel plate is supplied toprotect the underside of the countertopagainst steam rising from the dish-washer when the door is opened. If thecountertop is made of Corian®, gra-nite, marble or other solid, waterproofmaterial, the steam deflector should notbe used.

Squeeze a bead of sealant from thesupplied tube into the angle formedby the curved edge b of the cover-plate.

Align the plate c with the lower frontedge of the countertop (see illustra-tion) and use the supplied tacks tonail it in place.

On countertops with wood or lami-nate edging, the tacks should benailed through the rear holes of theplate.

Dishwasher installation

47

2. Installing the dishwasherunder the countertop.

It is preferable to install the main waterand electric supplies so that they canbe accessed through an adjacentcabinet, rather than situating them be-hind the machine. See the “Plumbing”and “Electrical” sections for proper con-nection procedures before continuing.

Certain steps in the installation proce-dures require that the dishwasher bepulled out of its opening. For this rea-son, perform the final plumbing andelectrical connections after the ma-chine has been levelled and the frontpanel has been mounted.

Install the slides.

Two slides are included and should beinstalled on the feet of the dishwasherbefore the machine is pushed underthe countertop. This will allow the ma-chine to slide easier, protect the floor,and allow adjustment of the rear level-ing legs from the front of the machine.

Place the slides, with the ratchet atthe rear, onto the dishwasher legs.

Unscrew the legs to raise the ma-chine to within 1/4" (5 mm) of theunderside of the countertop, andcheck that the machine is level, before sliding it into its opening.

Push the machine into the opening,making sure the electrical cable andhoses can reach their connectionpoints without being kinked.


48

Adjust the rear leveling legs to the re-quired height.

To raise the machine - turn clockwise.

To lower the machine - turn counter-clockwise.

Several turns may be needed to set thecorrect height. A low speed electric orcordless screwdriver can also be used.

Adjust the front leveling legs by push-ing on the foot with a slotted screw-driver.

Tipping the machine slightly, ifpossible, will make adjusting the frontlegs easier. Make sure the machine islevel when adjustments are complete.

The dishwasher should be raised until itjust touches the underside of the counter-top.


49

3. Installing the control panel.The control panel and hardware is packaged separately from the dishwasher. Itshould be installed using the following procedure.

If a GDU decor kit is being used , (toconvert an “i” dishwasher to a “U” ver-sion), the spacer bars g must first beremoved and stored for possible usein the future (See the separate instruc-tions for installing the GDU decor kit).If the GDU kit is not being used, skipthe following step.

To remove the spacer bars from thecontrol panel, place the panel on atable, printed side up, and gentlypush down on the spacer bars at apoint near the bottom of the controlpanel. This will release the mountingbolts from their slots.

Install the number of spacer bars grequired to align the lower edge ofthe control panel with the neighbor-ing cabinet drawer line.

Place the supplied seal b onto theventilation grill c.

Push the ventilation grill c into themetal backing plate.

Place the control panel d over thebacking plate and fasten it from theinside of the door e using the sixscrews provided.

Align and press the program knobsonto their shafts f.


50

4.Aligning the control panelwith the drawer fronts.The control panel can be alignedwith the drawer fronts of the kitchencabinets by adjusting the spacerbars.

Using an 8 mm socket, turn the nutclockwise or counterclockwise untilthe spacers reach the requiredheight.

If necessary, individual (or all)spacer bars can be removed.

Adjustment rangefrom 4 1/2" control panel with-(112 mm): out spacer bars,

to 5 3/4" control panel with(145 mm): four spacer bars,

to 6": using a fifth spacer bar(154 mm): (optional accessory).

After adjusting the control panelheight, cut off the plastic screw ex-cess.

5. Installing the custom door panel.

A custom door panel matching the kit-chen cabinetry can be installed on thedishwasher by using the provided tem-plates and bracket.Length: 21" - 25 3/4" (53.3 - 65.4 cm)Width: 23 1/2" (59.8 cm)

Note: The maximum panel length isonly applicable when no spacer barsare used.

After panel installation, see Step 6 “Ad-justing the door springs”.

Place a template on each end of thebracket as shown, making sure therule marks face the outside of thebracket.


51

Hang the bracket on the machinedoor.

Slide the top edge of the templatesunder the spacer bars and controlpanel.

Slide the mounting bracket up ordown until the oblong holes on themachine door align with the corre-sponding marks on the template (asshown in the left side of inset D.

Draw a line on each template that iseven with the top edge of the ad-jacent cabinet door (inset E).

Remove the bracket from the door.

Place the door panel on a flat sur-face, good side facing down, takingcare not to scratch the surface.Make certain that the bottom of thepanel is closest to you.

Place the bracket on the back of thedoor panel and adjust it so that:

– the lines you drew on the templatesalign with the upper edge of the doorpanel and;

– the mounting bracket is centered(left to right) on the door panel.

Tape the bracket to the door panel tohold it in place while the mountingholes are being drilled.

Proceed to step “Drill pilot holes ...”.


52

If the adjacent cabinetry (or ap-pliance) does not have drawers andalignment to a drawer line is im-possible:

Hang the bracket on the machinedoor, without the templates, andtighten the four locking screws onthe edges of the door panel.

Close the door.

Measure the distance from the ad-jacent cabinet (or appliance) doorbottom to the bottom of the mountingbracket (X).

Using measurement (X), draw a lineon the rear of the door panel (X) in-ches up from the bottom.

Remove the bracket from the ma-chine door and place it on the rear ofthe door panel so that:

– the bracket is centered left to right,and

– the bottom of the bracket is alignedwith the (X) line.

Tape the bracket to the door panel tohold it in place while the mountingholes are being drilled.

Drill pilot holes for the screws using a3/32" (2.5 mm) bit.

Attach the bracket to the panel usingthe 6 screws provided.

Remove the templates (if used).

The templates should be kept in caseyou want to install a different door panel on the dishwasher at a later date.

Attach the panel to the dishwasherby aligning the bracket tabs with theslots on the door.


53

Open the dishwasher door slightly. Ifthe locking screws on the edge of thedishwasher door can not be reached,the dishwasher will have to be pulledout of its recess a few inches.

Push up one side of the door paneluntil it touches the spacer bars (orcontrol panel if spacer bars are notbeing used) and lightly tighten theT20 Torx screw on the correspond-ing edge of the machine door.

Repeat the process with the otherside of the door panel.

Shut the door.

Check that the door panel is adjustedcorrectly. It should be snug at thetop and neatly aligned with thecabinet drawer and door lines. If itisn’t aligned properly, loosen the Torxscrews and readjust the panel

Once the door panel is positioned cor-rectly :

Open the dishwasher door.

Tighten all the Torx screws on the edges of the dishwasher door.

Use the provided caps to plug thelocking screw access holes.


54

6. Adjusting the door springs.The door springs are adjusted correctlywhen a half opened door remains inthat position when released.

If the door drops down, the spring ten-sion needs to be increased.If the door closes, the spring tensionneeds to decreased.

The adjusting screw is located in theupper front strip, on the left hand sideof the dishwasher.


Adjust the door springs to the cor-rect balance by using a TORX screw-driver:– turn clockwise to increase the

tension– turn counterclockwise to decrease

the tension.

7.Securing the dishwasher to the countertop.

To ensure the stability of the dish-washer, it must be attached to thecountertop after it has been positioned.

Insert one mounting bracket intoeach of the slots located at the leftand right side of the machine top.

Push the machine into its recess andif necessary, raise the dishwasher byextending the feet until it justtouches the underside of the counter-top.

If a steam deflector is installedunder the countertop, the bracketholes must align with the slots in thedeflector.


55

Open the dishwasher door andusing flat head screws, secure thedishwasher to the countertop byscrewing through both the mountingbrackets and the steam deflector.

Make certain that the white rubberseal located at the top, outer edgeof the dishwasher is tight againstthe bottom of the countertop.

Do not drill any additional holesthrough any portion of the washcabinet. If in doubt how to securethe dishwasher, please call theMiele Service Department.

For Corian® or granite countertops,fasten the dishwasher to the adjacentcabinets as follows:

For openings greater than 23 5/8"(60 cm) wide:

Pull the dishwasher 4" (10 cm) out ofits opening.

Insert the tab of each optional mount-ing bracket into the guide hole ontop of the dishwasher, and thenswing it to the right or left as required.

Push the dishwasher back into its open-ing, align and fasten it to the adjacentcabinets using 2 screws for eachbracket.


56

For openings exactly 23 5/8" (60 cm)wide:

Open the dishwasher door andremove the caps covering the mount-ing holes on the outer edge of thewash chamber.

Fasten the dishwasher to the ad-jacent cabinets using the suppliedscrews and bushings. Make sure abushing is placed over the screw be-fore inserting it into its mounting hole.

Tighten the screws and replace thecaps.

The side mounting holes shouldonly be used for securing thedishwasher if the opening isexactly 23 5/8" (60 cm) wide. Useof this method on larger openingswill damage the machine andcause leaks.

8. Installing the toekick.For kitchens utilizing one continuousor a cabinet matching toekick

To prevent damaging the frontpanel, and before installing the toe-kick, measurements must be takento ensure that the toekick will not in-terfere with the complete opening ofthe dishwasher door.

The panel overhang (P), and toekickdepth of recess (R), determine the maxi-mum dishwasher toekick height (H).

If the panel contacts the toekick whilethe dishwasher door is being opened,the dishwasher toekick must be cutshorter or recessed deeper.

If (H) is equal to or less than the toekickheight of the adjoining cabinetry, no in-terference will exist, provided that (R) isat least 3/4".

Note: If a decorative or flush mount toe-kick is desired, and (R) is less than3/4", other modifications, such as beve-ling the top rear edge of the toekick,may be necessary.


57

For kitchens utilizing the included plas -tic toekick

The included toekick will fit withoutmodification when:– The machine is set to its maximum

height (legs fully extended), and– the toekick is recessed as far as

possible (4 ").

If the machine height is less than maxi-mum, or if the toekick is recessed lessthan 4 ", the toekick must be shortened(see following page).

After installation, carefully open thedishwasher door to check that thefront panel does not hit the toekick.If it does, remove the toekick and trimit accordingly.

Adjusting the toekick recess.

To adjust the depth (recess) of thetoekick, release the tension on thespring clips as shown, and push themounting brackets included in the in-stallation kit in as far as possible.


58

Trimming the toekick

The rear of the toekick has two cuttinglines.

Screw the toekick onto the installedbrackets, with the cutting lines to-wards the top, and pull out evenlyuntil it aligns with the toekick of theadjoining cabinets.

The toekick cannot be pushedback in. It must be unscrewed, sothat the tension on the springclips can be released. Thebrackets can then be pushed in,and the toekick re-attached.

Carefully open the dishwasher dooruntil it hits the toekick.

Using the front lower edge of thedoor panel as a guide, draw a lineacross the toekick.

Unscrew and remove the toekick.

If one of the cutting lines is close tothe line just drawn, score the front ofthe toekick, and snap off the excess,otherwise, trim the toekick along theline using a saw.

Screw the toekick back onto thebrackets, with the cut edge at thebottom.

If the dishwasher door does not opencompletely, the toekick may need fur-ther trimming.


59

Electrical connectionIt is the responsibility and obligationof the customer to ensure that theelectrical and plumbing installationis carried out by a qualified installerin compliance with national andlocal codes and ordinances.

Disconnect the appliance from thepower supply before servicing the ma-chine by pulling the plug or turning offthe circuit breaker.

Specifications.

Power Supply: 120 VAC, 60 Hz

Rated Load: 12.5 A / 1500 W

Circuit breaker:15 AMPS

The unit is equipped with a 5 ft (1.5 m)power supply cord for connection to a120 V, 15 AMP grounded receptacle.

Using an outlet:

It is recommended that the poweroutlet for the appliance be installedin a cabinet or on a wall adjacent tothe undercounter space in which theappliance itself will be located. Anopening through the partition be-tween the compartments of 1 1/2" (3 to 4 cm) can be made to allow theplug to pass through.

Make certain that there are no roughedges that could damage the powercord. If metal cabinets are used,place the supplied rubber grommetaround the edge of the opening be-fore passing the cable through.

Exercise care when pulling the dish-washer in or out, so as not to dam-age the power cord or hoses.

GROUNDING INSTRUCTIONS.

THIS APPLIANCE MUST BEGROUNDED.

In the event of a malfunction or break-down, grounding will reduce the risk ofelectric shock by providing a path ofleast resistance for the electric current.This appliance is equipped with a cordhaving an equipment grounding con-ductor and a grounding plug. The plugmust be plugged into an appropriateoutlet that is installed and grounded inaccordance with all local codes and or-dinances.

WARNING - Improper connectionof the equipment grounding con-ductor can result in the risk ofelectric shock. Check with a quali-fied electrician or service repre-sentative if you are in doubt as towhether the appliance is properlygrounded. Do not modify the plugprovided with the appliance; if itwill not fit the outlet, have aproper outlet installed by a quali-fied electrician.

Electrical connection

60

Permanent Connection (Hard Wiring).

For hard wiring, the power cord mustbe disconnected from the terminal boxlocated at the lower left front of the dish-washer, behind the toekick and servicepanel. Pass the permanent power sup-ply cable through the strain relief andsecure it to the terminal box.

Connect:

L1 (Black) to L on terminal block

N (White) to N on terminal block

GRND To ground connector

GROUNDING INSTRUCTIONS

This appliance must be connectedto a grounded metal, permanent wiring system, or an equipment-grounding conductor must be runwith the circuit conductors and con-nected to the equipment groundingterminal or lead on the appliance.

Use copper conductors only.

Warning.Hardwiring the dishwashershould only be done if requiredby local electrical codes, andthen in a manner consistent withthose codes. Do not cut the plugoff the power supply cord andconnect it directly to the housewiring.

Electrical connection

61

Plumbing It is the responsibility and obligationof the customer to ensure that theelectrical and plumbing installationis carried out by a qualified installerin compliance with national andlocal codes and ordinances.

To help protect your home, all dish-washers that carry the following blueand white sticker are designed to shutoff the water and drain the wash cham-ber in the rare event of an internalwater valve failure.

In order for this function to be active,the door must be tightly shut, a tem-perature must be selected, and theprogram selector knob must be inthe “End” position.

Hot water supply specifications:

Recommended temperature: 120°F(49°C)

Maximum temperature: 140°F (60°C) Water pressure: 14.5 - 145 psi

(1 - 10 bar)

An air gap is built into the water inletsystem to prevent potable water frommixing with waste water.

Hot water connection.

New plumbing:

The water inlet hose comes equippedwith a 3/4" female hose thread connec-tor. This can be directly connected to ashut off valve with 3/4" male hosethread ends. It is preferable that the hose assemblybe installed vertically so the hoseexits from the bottom of the valve box. If this is not possible, it can be installedhorizontally as shown, provided the hoseexit remains beneath the main body ofthe box (see illustration). (The “lightningbolt” should be above the “arrow” whenthe installation is complete).The valvebox should also be installed so that it isat least 8" (24 cm) above the floor (orbase of the cabinet), and so the excesscoiled hose will remain lower than thebox at all points.A 2" x 4" (60 x 115 mm) cutout in eitherthe side or bottom of the cabinet adjoin-ing the dishwasher is necessary if thevalve box needs to be passed through.

Plumbing

62

Existing plumbing:

If the standard 3/8" copper plumbingfor a dishwasher already exists with acompression fitting and valve as pic-tured:

Cut the 3/8" copper tubing after thevalve.

Install the 3/8" compression to 3/4"MHT (Male Hose Thread) adapter(supplied with the machine), as illus-trated.

Connect the inlet hose to the existingvalve/adapter assembly.

Electrical wiring and componentsshould not come into contact withany plumbing fixtures or hoses.

Do not, under any circumstances,cut the intake hose. If the hose iscut, the dishwasher will not work,you will have a water leak andyou could be injured. If the hoseis too long, coil it neatly andplace it behind the machine.

Plumbing

63

Drain system specifications:

The machine comes equipped with:

– A 5 ft. long (1.5 m) flexible drainhose with an internal diameter of 7/8"(22 mm).

– A built-in swivel connector whichallows the drain hose to be routed inany direction.

– A built in non-return valve on the dis-charge side to prevent waste waterfrom flowing back into the dish-washer.

– A built-in odor trap on the dischargeside to prevent odors from enteringthe kitchen.

Maximum drain height: 3 ft (1 m)

Maximum drain hose length: 12 ft(3.5 m)

Do not shorten the drain hose.

Electrical wiring and componentsshould not come into contact withany plumbing fixtures or hoses.

IMPORTANT:The dishwasher should be con-nected directly to the drain line.

Drain connection:

D = 24" (60 cm) (nominal)

Connect the supplied drain hose to thedrain pipe of the kitchen sink either:

A - above the trap using the clamp pro-vided, or

B - to the dishwasher connector of thegarbage disposal.

When connecting the drain hose tothe garbage disposal, make sure toremove the knockout from the con-nection nipple. (See disposal manu-facturers instructions for this proce-dure.)

A sample of a correct water and draininstallation of a dishwasher is shown.

A hose that attaches to a sink spraycan burst if it is installed on thesame water line as the dishwasher. If your sink has one, it is recom-mended that the hose be discon-nected and the hole plugged.

Plumbing

64

Venting the drainage system

Only if the dishwasher drain hose isconnected to a floor drain or to adrain pipe that is below the level ofthe lower baskets wheels , the drainmust be vented; otherwise the water in-side of the dishwasher may siphon outduring the course of a wash program.

Vent the drain:


Cut off the vent cap located at theright rear of the dishwasher, behindthe filters, as illustrated

Additional note.

Since all Miele dishwashers areequipped with an odor trap and non-re-turn valve, the drain hose can be con-nected directly to the drain pipe as illus-trated.

If plumbing codes require an externalair gap on the discharge side of thedishwasher, the following requirementsmust be met:

– No part of the drain hose should behigher than 39" (1 m).

– If installed horizontally, the drainhose can be up to 12 ft. (3.5 m) long.If the drain hose is angled upwardsin any way, it cannot be longer than5 ft. (1.5 m).

– The drain connection should bemade as close as possible to thedishwasher.

– The internal diameter (7/8" or 22 mm)of the drain hose should not be re-duced beyond 3/4" at any point.

Plumbing

65

Technical DataHeight 33 1/8" (84 cm) adjustable to 35" (89 cm)

Width 23 1/2 " (59.8 cm)

Width of opening 23 5/8" (60 cm)

Depth 22 1/2" (57 cm) U and i models

Depth with door open 47 1/2" (120.5 cm) U and i models

Weight approx. 130 Ibs (57 kg)

Voltage 110/120 V AC

Rated load 12.5 A / 1500 W

Fuse rating 15 A

Water pressure 14.5 - 145 psi (1 - 10 bar)

Hot water connection 120°F (49°C ) (max 140°F (60°C))

Drain height 3 ft (1 m) maximum

Drain length 12 ft (3.5 m) maximum

Power cord length approx. 5 ft (1.5 m)

Technical Data

66

Alteration rights reserved (G868) /000 2498

These instructions are printed on 100% recycled paper and are completely Biodegradable.

corel ventura - g868usa · operating instructions for the g 868 dishwasher to prevent accidents and...

Documents