control systems product overview - power & control€¦ · product overview. ats controllers...
TRANSCRIPT
ATS controllers
InteliATS NT STD and PWR models
are new controllers designed to
monitor the AC mains supply for
under/over voltage, under/over
frequency and voltage unbalance. frequency and voltage unbalance.
Any mains supply disproportion
causes the remote gen-set to start
and makes change over for both
generator and mains contactors.
The gen-set requires a remote start
type control unit (e.g. the ComAp
InteliLite NT MRS 10 controller).
Automatic transfer between mains and
generator power
On-site controller confi guration
Remote confi guration and monitoring
Inputs/outputs confi gurable for various Inputs/outputs confi gurable for various
customer needs
Mains measurements: U1-U3, Hz
Generator measurements: U1-U3, Hz
I1-I3, kVA, kW, kVAr, kWh (PWR)*
Active SMS/E-mails (PWR)*
Event based history fi le (PWR)*
InteliATS NT
STD, PWR
* Stated features available on this model
STD, PWR
Gen-set controllers
InteliLiteNT MRS models are
integrated controllers for single
engine control in Manual and
Remote Start applications,
featuring full gen-set monitoring
and protection.and protection.
The 4 MRS models are identifi ed
by a number which defi nes model
capability (10, 11, 15, 16).
* Stated features available on this model
InteliLiteNT AMF models are
integrated controllers for
gen-sets operating in single
standby mode. They meet all
possible requirements for AMF
applications, including modem applications, including modem
control, user confi guration and full
gen-set monitoring and protection.
The 2 AMF models are identifi ed
by a number which defi nes model
capability (20, 25).
* Stated features available on this model
MainsCompactNT is designed
for multiple (up to 31) gen-sets
controlled by InteliCompactNT and
operating in parallel to mains.
MainsCompactNT controller
connects the group of gen-sets to
the mains.
InteliCompactNT SPtM and MINT
models are new integrated
controllers for gen-sets operating
in both standby and parallel
modes. The controllers feature modes. The controllers feature
easy to use functionality,
confi guration and installation and
benefi t from a built-in synchronizer
and digital isochronous load
sharer. Native cooperation of up to
32 gen-sets is a standard feature.
Support of engines equipped with
ECU – J1939 interface (15, 16)*
Automatic/Manual start/stop of gen-set
Push buttons and LEDs for simple control
Parameters adjustable via keyboard or PC
3 phase Generator protections 3 phase Generator protections
Generator measurements (50 / 60 Hz):
U1-U3, I1-I3, Hz, kVA, kW, kVAr, kWh
Confi gurable programmable inputs
and outputs
Event based history fi le (15, 16)*
Web based monitoring and control
Wide range of remote communications
Support of engines equipped with
ECU – J1939 interface (25)*
Automatic/Manual start / stop of gen-set
Push buttons and LEDs for simple control
Parameters adjustable via keyboard or PC
Mains measurements (50 / 60 Hz): U1-U3, Hz Mains measurements (50 / 60 Hz): U1-U3, Hz
Generator measurements (50 / 60 Hz):
U1-U3, I1-I3, Hz, kVA, kW, kVAr, kWh
Confi gurable programmable inputs
and outputs
Event based history fi le (25)*
Web based monitoring and control
Wide range of remote communications
Mains measurements: U, I, Hz, kW, kVAr,
kVA, PF, kWh, kVAhr
Bus measurements: U, I, Hz
Mains failure detection using integrated
mains protections
Systems with as well as without master
generator breaker supported
Confi gurable level switches based on mains
import or object consumption
Event based history fi le
AMF, continuous parallel function
Peak shaving, Mains export/import
Support of engines equipped with ECU
(J1939, Modbus and other proprietary
protocols); alarm codes displayed in protocols); alarm codes displayed in
text form
Baseload, Load sharing
Optimizing the running of each engine in
multi-gen-set mode
Inputs/outputs confi gurable for various
customer needs
Event based history fi le
InteliLite NT AMF
MainsCompact NT
InteliCompact NT
SPtM, MINT
InteliLite NT MRS
AMF
MRS
Gen-set controllers
InteliSysNT is an expandable NT is an expandable NT
controller for both single and
multiple gen-sets operating
in standby or parallel modes,
especially in CHP (cogeneration)
and other complex applications.
Detachable construction (consisting
of IS-NT-BB and IS-Display or
InteliVision) allows easy installation
with the potential for many
different extension modules different extension modules
designed to suit individual
customer requirements.
CHP support (programmable PID loops and
other built-in PLC functions)
Support of engines equipped with ECU
(J1939, Modbus and other proprietary
protocols); alarm codes displayed in
text form
Baseload, Import/Export, TempByPower,
Peak shaving, Voltage and PF control
Optimizing the running of each engine in
multi-gen-set mode
Inputs/outputs confi gurable for various Inputs/outputs confi gurable for various
customer needs
Event based history fi le with up to
1000 records
InteliSys NT
Generator controllers
InteliGenNT GeCon provides
comprehensive generator
protection and control for single
or multiple gen-sets equipped
with an independent engine
controller. Special confi gurations
optimized for use in marine and
land-based installations allow land-based installations allow
customers to select a tailored
solution for their application with
the option of modifi ed options for
critical applications.
GeCon only controls generator part of a
gen-set since the engine control is provided
by an engine controller
Two GeCon controllers can be used in
either Master & Hot-Standby or Master &
Protection applications
Cooperation with the engine controller is
achieved using minimum inputs and outputs achieved using minimum inputs and outputs
Accepts external automatic or manual control
of both engine and breaker
Baseload, Import/Export, Analog external
load control
Optimizing the running of each engine in
multi-gen-set mode
Event based history fi le with up to 500 records
InteliGen NT GeCon
InteliMainsNT is designed for
multiple (up to 31) gen-sets
operating in parallel to mains.
InteliMains controller connects
the group of gen-sets to the
mains. It can serve as a bus-tie mains. It can serve as a bus-tie
synchronizing controller between
two groups of gen-sets.
Mains measurements: U, I, Hz, kW, kVAr,
kVA, PF, kWh, kVAhr
Bus measurements: U, I, Hz
Mains failure detection using integrated
mains protections
Bus-tie application Bus-tie application
Selectable partial or full MCB control
Confi gurable level switches based on mains
import or object consumption
Event based history fi le
InteliMains NT
InteliGenNT is a comprehensive NT is a comprehensive NT
controller for both single and
multiple gen-sets operating
in standby or parallel modes.
Compact construction is optimized
for these purposes; various HW
modifi cations allow the customer
to select the optimum type for a
particular application.
AMF, continuous parallel function
Support of engines equipped with ECU
(J1939, Modbus and other proprietary
protocols); alarm codes displayed in
text form
Baseload, Import/Export, Peak shaving,
Voltage and PF control
Optimizing the running of each engine in
multi-gen-set mode
Inputs/outputs confi gurable for various Inputs/outputs confi gurable for various
customer needs
Event based history fi le with up to
500 records
Integrated PLC programmable functions
InteliGen NT
Engine controllers
Off-road machinery controllers
InteliDrive DCU Industrial is a highly fl exible sophisticated engine controller, which
features outstanding control, monitoring and protection for both mechanical and
electronic diesel / gas engines as well as peripheral equipment. Industrial software
contains a set of programmable functions like comparators, timers, PID loops, logic
functions and others for easy solution of any industrial application.
InteliDrive Lite is a cost effective sophisticated engine controller, which
features outstanding control, monitoring and protection for both mechanical
and electronic diesel / gas engines in one unit. The extended product family
offers a range of engine specifi c versions suitable for land-based and marine
non-classifi ed applications.
InteliDrive Mobile is a highly fl exible sophisticated mobile electronic controller,
which features outstanding control, monitoring and protection for diesel and
gas engines as well as driven technology. The controller offers a range of
specifi c functions suitable for mobile applications as hydraulic system control,
communication with sensors and operational devices control.
InteliDrive DCU Marine is an engine controller designed specially to meet the
demanding needs of the marine market; providing a high level of performance
coupled with extensive J1939/J1587 communication capabilities and incorporating
hardwired safety functions and primary/secondary power switching.
Engine sequencing and control
J1939 interface supporting wide range of EFI engines
Engine monitoring and protections
Integrated PLC
Speed measurement from magnetic pick-up or from J1939
Running hours meter, number of starts counter
14 binary inputs, 14 binary outputs, 8 analog inputs
Input/output confi guration
Setpoints adjustable via keyboard or PC
Recommended extension: ID-SCM, ID-SCM1
Engine control, monitoring and protection
J1939 interface supporting wide range of EFI engines
Speed measurement from pickup or from J1939
6 confi gurable binary inputs and outputs, 3 cofi gurable analog inputs
Support of plug-in modules: IL-NT AIO, IL-NT AOUT8, IL-NT BIO8, IL-NT IO1
PLC functions: PID loop, Comparators, Timers
Setpoints adjustable via keyboard or PC
Password protection
Engine control, monitoring and protections
Integrated PLC for driven technology control
J1939 interface supporting wide range of EFI engines
Internal GSM modem and GPS location
Confi gurable 16 binary inputs, 16 binary outputs, 8 analog inputs,
8 analog in (or) outputs for hydraulic proportional valves
Operating temperature: -25°C to +70°C (optionally -40°C to +85°C)
Enclosure IP67
Anti condensation (Gore Membrane Venting)
Engine sequencing and control
Engine monitoring and protection
Confi gurable J1939 interface with electronic engines including ECU
Alarm indication
Redundant module ID-RPU with hardwired safety functions activated in
backup mode
Automatic switchover to backup mode in case of detection of main unit failure
Setpoints adjustable via keyboard or PC
Recommended extension: ID-RPU
InteliDrive DCU Industrial
InteliDrive Lite
InteliDrive Mobile
InteliDrive DCU Marine
Accessories
E X T E N S I O N M O D U L E S IA-NT IL-NT IC-NT MC-NT IG-NT/IS-NT IM-NT ID-Lite ID
I-AOUT8 ANALOG OUTPUT EXTENSION MODULE
ID-RPU REDUNDANT PROTECTION UNIT
ID-SCM SPEED CONTROL MODULE
IG-IOM ANALOG/BINARY INPUT/OUTPUT MODULE
IGL-RA15 REMOTE ANNUNCIATOR
IGS-PTM ANALOG/BINARY INPUT/OUTPUT MODULE
IL-NT AIO ANALOG INPUT/OUTPUT MODULE
IL-NT AOUT8 ANALOG OUTPUTS FOR PWM GAUGES MODULE
IL-NT BIO8 BINARY INPUT/OUTPUT (PWM) MODULE
IL-NT IO1 ANALOG INPUT/OUTPUT MODULE
IS-AIN8 ANALOG INPUT MODULE
IS-BIN16/8 BINARY INPUT/OUTPUT MODULE
NT-Converter LOAD SHARING INTERFACE MODULE
C O M M U N I C A T I O N M O D U L E S IA-NT IL-NT IC-NT MC-NT IG-NT/IS-NT IM-NT ID-Lite ID
IB-Lite ETHERNET MODULE
I-CR CAN REPEATER MODULE
ID-COM COMMUNICATION MODULE
IG-IB INTERNET BRIDGE
I-LB+ LOCAL BRIDGE
IL-NT RS232 RS232 EXTENSION BOARD
IL-NT RS232-485 DUAL PORT EXTENSION BOARD
IL-NT S-USB PLUG-IN SERVICE USB MODULE
E C U C O M M U N I C A T I O N M O D U L E S IA-NT IL-NT IC-NT MC-NT IG-NT/IS-NT IM-NT ID-Lite ID
I-CB ECU COMMUNICATION BRIDGE
R E M O T E D I S P L AY S IG-NT IS-NT IM-NT ID
IG-Display LT GC ADDITIONAL REMOTE DISPLAY
InteliVision CONTROLLER COLOUR DISPLAY UNIT
I-RD-CAN REMOTE DISPLAY WITH CAN BUS INTERFACE
IS-Display DETACHABLE DISPLAY MODULE
S I M U L A T O R S IA-NT IL-NT IC-NT MC-NT IG-NT/IS-NT IM-NT ID-Lite ID
MultiKit SIMULATOR OF VARIOUS APPLICATIONS
StarterKit PORTABLE SIMULATOR
A D D I T I O N A L M O D U L E S IA-NT IL-NT IC-NT MC-NT IG-NT/IS-NT IM-NT ID-Lite ID
IG-AVRi AVR INTERFACE
I-LBA LOW BATTERY ADAPTOR
I-RB 8 OR 16 RELAYS BOARD
Mains protections
3-phase mains protection
Vector shift protection
2 stage over/under frequency protections
2 stage over/under voltage protections
Voltage asymmetry protections
Meets applicable Meets applicable
requirements of
IEC 60255
Designed with the aim
of satisfying the G59,
ETR113, G77, G83 and
G10 guidelines
NPU-FUV
PC tools
M O N I T O R I N G S W IA-NT IL-NT IC-NT MC-NT IG-NT/IS-NT IM-NT ID-Lite ID
DriveMonitorPC MONITORING TOOL
InteliMonitorPC MONITORING TOOL
InteliSupervisorPC TOOL FOR GEN-SET FLEET MANAGEMENT
WinScopeSPECIAL GRAPHICAL CONTROLLERS‘ MONITORING SOFTWARE
C O N F I G U R A T I O N S W IA-NT IL-NT IC-NT MC-NT IG-NT/IS-NT IM-NT ID-Lite ID
DriveConfi gPC CONFIGURATION TOOL
GenConfi gPC CONFIGURATION TOOL
C O N F I G U R A T I O N A N D M O N I T O R I N G S W IA-NT IL-NT IC-NT MC-NT IG-NT/IS-NT IM-NT ID-Lite ID
LiteEditPC CONFIGURATION AND MONITORING TOOL
Integrated protection solution for generators operating in
parallel to mains applications
InteliProtec
2 stage over/under voltage protections
2 stage over/under frequency protections
Vector shift
Rate of change of frequency Rate of change of frequency Rate of change of frequency Rate of change of frequency
Over current, NVD
Reverse power
Earth fault protections
Short term parallel
protection
Satisfi es G59 guidelines
Full name Short name Pictogram
InteliATSNT IA-NT
InteliLiteNT IL-NT
InteliCompactNT IC-NT
MainsCompactNT MC-NT
InteliGenNT IG-NT
InteliSysNT IS-NT
InteliGenNT and InteliSysNT IG-NT/IS-NT
InteliMainsNT IM-NT
InteliDrive Lite ID-Lite
InteliDrive ID
InteliVision IV —
These pictograms are designed to help you visually associate which Accessories and PC tools are suitable for use with which controllers.
We have also provided both the full product names and their abbreviated shorter names to help you recognize and identify the products more easily.
If you look throughout the overview you will see these icons appearing next to the relevant or associated product.
Pictograms and short names
PLC EditorNew configuration tool for selected ComAp controllers
Key features of new releaseKey features of new release
PLC functions can be moved both horizontally PLC functions can be moved both horizontally and vertically
Colour-coded and linked to relevant functions
Blocks can be organized to refl ect the real process fl ow
Groups of blocks can be separated on each sheet to form sub-sets within the design
Detailed descriptions of inputs and outputs come complete with useful hints
The new ComAp PLC Editor is currently free to users who complete a short questionnaire on the ComAp website www.comap.cz allowing user analysis to be reviewed.
For more information visit www.comap.cz
InteliVision is a new generation color display unit for either InteliGendisplay unit for either InteliGenNT, InteliSysNT, InteliSysNT NT,
InteliMainsNT or InteliDrive controllers. It is designed as a simple, easy to use Plug and designed as a simple, easy to use Plug and
Play solution, which also features our unique Play solution, which also features our unique TRENDS monitoring as a standard feature.
www.comap.cz/intelivision
The interactive simulator provides a taste of the new InteliVision, with demo and preview options illustrating screen information and function.
simulator
ONLINE
© ComAp. 2009-11/CPLEPROV. All rights reserved.
Specifi cations in this material are subject to change without notice.
Manufacturer Local Distributor / Partner
ComAp, spol. s r. o.Czech Republic
Phone: + 420 246 012 111Fax: + 420 266 316 647E-mail: [email protected]
Internet: www.comap.cz
www.comap.czSpecial Controllers‘ Monitoring Software from ComAp
Cabo Corrientes and Puerto Madryn, Argentina
The Argentinian Coast Guard vessels GC 73 Cabo Corrientes and GC 78 Puerto Madryn are both equipped with ComAp generator and propulsion engine control and monitoring systems.
The onboard generators powered by Perkins engines use InteliGenNT Marine, whilst the ship’s MTU propulsion engines rely on two InteliDrive DCU Marine and additional modules to provide a control package which includes controlling engine speed and gear box. The complete system is easily managed using two full colour InteliVision and IG-Display units.
Power plant, Switzerland
The power plant stands in the built-up area “Am Mark” in Heerbrugg and provides power for the nearby residential apartments and a large shopping centre.
The plant features an Olympian GEP400-2 diesel gen-set producing 400 kVA with control and monitoring from ComAp using InteliGenNT unit in MINT application with two InteliMainsNT units in MGCB application.
Boss Industries, USA
“ComAp’s compressor and engine control panel solution optimizes natural gas production on Boss’s booster units by providing accurate process control using digital pressure transducers.
Our customers are very happy with its event history capabilities as well as its compressor and engine protective features. We also value the fact that the ComAp ID-DCU panel is fully compatible with future electronic emission certifi ed engines and control capabilities. BOSS Industries has standardized on the ComAp panel for our gas well booster compressor units.“
Ed Ketcham, VP Saleswww.bossair.com
Free
Download
Power plant, Switzerland
Boss Industries, USA
Cabo Corrientes and Puerto Madryn, Argentina