contact gsm-16 quick start guide
TRANSCRIPT
Saint Petersburg, 2017
Contact GSM-16Quick start guide
Ver. 1.1
www.ritm.ru/en 2
Contact GSM-16. Quick start guide.
Prepare your deviceFirst, prepare your devices which you want to connect, according to the Data sheet of the Contact GSM-16.
Please note, you must do following steps:
⢠Insert your device into the Contact Box (7Ah or 1,2Ah).⢠Connect your device to 12 V power supply.⢠Put your SIM cards into the SIM slots. Please make sure,
that your SIM Card does not require a password.⢠If you need to, connect your wired keypad to your device.⢠Connect another accessories.
TELCO
SIM1
SIM2HL5
HL6
JMP1 JMP2 JMP3LAN
HL3
MicroUSB
PROGRAM
SPK TELCO
HL4
RS-485
ANT1
ANT2
A
B
GND
SA1
OUT
3
OUT
2
OUT
1
TM LED
GN
D
DATA +U â + â +â+ â+ â+ â+ â+ â+ â+ â+1 82 3 4 5 6 7
GN
D
+12V
CPW
XT2TAMPER RELAY
â +
SENS
PWRDATA
MESRS485
www.ritm.ru/en 3
Contact GSM-16. Quick start guide.
Online ConfigurationThe easiest and the fastest way to configure the device is via Online Configuration.Go to www.eu.ritm.ru. You can choose the language in the upper right corner. Click the Registration for sign up.
Fill out the registration form
www.ritm.ru/en 4
Contact GSM-16. Quick start guide.
After that you will get the e-mail for authorization, follow the link in that email and you will see this page.
Click on the button âOpen Monitoring interfaceâ. You can select âRun Object Add Wizard automaticallyâ, or open this wizard later.
Now you should see the main page of GeoRitm interface.
www.ritm.ru/en 5
Contact GSM-16. Quick start guide.
If you didnât open the âAdd Object Wizardâ yet, you can click on plus.
And add a group and an object. You will see this page.
Just click âNextâ.
www.ritm.ru/en 6
Contact GSM-16. Quick start guide.
Here you should put the IMEI of your device. You can find it out from the Data sheet of your device, or written on the modem in your device.
Click âNextâ.
www.ritm.ru/en 7
Contact GSM-16. Quick start guide.
Click âNextâ.
If you see this page, the server now identified your Contact GSM-16. Click âNextâ.
www.ritm.ru/en 8
Contact GSM-16. Quick start guide.
Here you can give a name for your object and add it to the group. You can choose an existing group, or add a new one right here.
After that click âNextâ. Your Contact GSM-16 is ready to work. You can give Coordinates, or Address to your device, and you will see it on the map.
www.ritm.ru/en 9
Contact GSM-16. Quick start guide.
You can click on the image of your Contact GSM-16 on the map and see the events, general report and objectâs card (you can open it from the left menu as well).
When you will open objectâs card, you can choose the âEquipmentâ section and under the picture of Contact GSM-16 you will see the link âSetup a deviceâ. It will open the wizard of settings of your Contact GSM-16, and you can configure it.
www.ritm.ru/en 10
Contact GSM-16. Quick start guide.
Configure your deviceAfter the successful connection you will see this page.
If you see the available update K16RT1 or K-16C (red color), please click on it. You will see the update in progress.
In the Object section, you can change the number of an object.
! You should use this number, when you will configure your areas, otherwise the alarms from the areas will create an incorrect messages.
When you change some setting, you have to click on the âSave changesâ button before you leave the current page!
www.ritm.ru/en 11
Contact GSM-16. Quick start guide.
Configuration of wireless devicesTo connect the wireless sensors or keypads to your device, you will need your Radio system on (by default it is already ON).
! You can configure it only if you make a new Radio system, and the old one will be deleted.
Now you have a default Radio system, and if you are sure you donât need to change anything else, do not change these settings.
www.ritm.ru/en 13
Contact GSM-16. Quick start guide.
Wireless sensorsTo configure the wireless sensors, go to the âRadio sensorsâ section.
Prepare your sensor to be connected, according to the sensorâs Data sheet, and click âaddâ.
You will see the process of the sensor being added.
www.ritm.ru/en 14
Contact GSM-16. Quick start guide.
Then you will see your sensor in the sensorâs list.
Wireless keypadTo configure the wireless keypad, go to âKeypadsâ section, prepare your keypad to be connected, according to the Data sheet of the keypad, and click âAdd keypadâ
www.ritm.ru/en 15
Contact GSM-16. Quick start guide.
You will see the process of keypad being added.
Afterwards you will see your keypad in the settings list.
The same way, you can add your keyfobs in the keyfobs section.
www.ritm.ru/en 16
Contact GSM-16. Quick start guide.
When you add your radio sensors or keypads, you can see, how they function in the âRadio device mapâ section.
www.ritm.ru/en 17
Contact GSM-16. Quick start guide.
Configuration of wired keypadsGo to the âKeypadsâ section.
Wired keypad should be already connected to your device.
Click add and your keypad will be connected authomatically. You will see it in the list.
Go to User codes page.
Here you can make codes to control your areas from the keypad.
www.ritm.ru/en 18
Contact GSM-16. Quick start guide.
Set-up via USB-cable
The alternative way to set-up your device is via the USB-cable.
Download the software⢠Go to our website www.ritm.ru, in the right top corner
you can choose the English language. ⢠Then go to âDownloadsâ.⢠Open the âCommon software for the set-up of all of
Ritmâs devicesâ, click on the link and download file.⢠Then open âA set of drivers for connecting Ritmâs devices
to the common setup softwareâ, click on the link and download this file as well.
www.ritm.ru/en 19
Contact GSM-16. Quick start guide.
Install the software
Unzip archive Drivers, and Install the downloaded Driver (Drivers\CP210x_VCP\CP210x_VCPInstaller_x64 or Drivers\CP210x_VCP\CP210x_VCPInstaller_x32), depending on the version of your operating system:
⢠Accept the agreement, click next.
Also, you will need to install driver of virtual com port (from \Drivers\ST_VCP\VCP_V1.3.1_setup, or \Drivers\ST_VCP\VCP_V1.3.1_setup_x64), depending on your operating system:
⢠Same steps: click next, and finish.
www.ritm.ru/en 20
Contact GSM-16. Quick start guide.
Check the connection of the device to your PCOpen the PC manager.
Click on the Device Manager and look at COM ports. Port for RITM USB is called âSilicon labs CP210x USB to UART Bridge (COM4)â.
www.ritm.ru/en 21
Contact GSM-16. Quick start guide.
! Please remember the number of your com port, it will be important in the future.
Open the configuration wizardRun the downloaded configuration program from the file, it will look like this:
In the right bottom corner you can choose the language.
After that, for the first time, it may be necessary to download the latest version of the software.
Here you can choose your COM port (use the port which you saw in device manager), leave the âMaster codeâ empty and click âconnectâ.
Thereafter, set-up the device as described previously.
www.ritm.ru/en 22
Contact GSM-16. Quick start guide.
GPRS and Communication channels Configurations
! When you change some settings, you have to click on âSave changesâ before you leave the current page!
Go to Device Details, where you can find general information about your Contact GSM-16.
Here you should copy the IMEI of your Contact GSM-16, and check the registration in GSM network.
If you have bad reception conditions of GSM, or SIM card doesnât work, you will see, that SIM has âNo registration in GSM networkâ.
www.ritm.ru/en 23
Contact GSM-16. Quick start guide.
Now you have to configure the GPRS connection.
Go to the section âGPRS parametersâ and fill it according to your own settings. You can find out the settings from your GSM provider. Make sure, there is no tick on âSpecify APN configuration automaticallyâ.
www.ritm.ru/en 24
Contact GSM-16. Quick start guide.
Next you will have to set up the connection to eu.ritm.ru server.
Click on the Communication channels.
Create two âdataâ channels. Both of them should use the SIM1 GPRS-online ContactID Connection.
Later on you can make more channels, or change the mode if you need to.
! Make sure to put the tick on âORâ; it means, that the SIM card will use second channel of connection, if the first one is not working.
To configure the first channel, type into the boxes of âConnection settingsâ:
⢠address dev1.eu.ritm.ru ⢠a port number 9426. ⢠the password â âTestTestâ.
To configure the second channel, type into the boxes of âConnection settingsâ:
⢠address dev2.eu.ritm.ru ⢠a port number 9426.⢠the password â âTestTestâ.
i To choose the object numbers, areas numbers and users numbers you have to type value in the direct box by the PC keyboard.
www.ritm.ru/en 25
Contact GSM-16. Quick start guide.
Now you can login into eu.ritm.ru and add your object to the system.
www.ritm.ru/en 26
Contact GSM-16. Quick start guide.
Change History
Revision Revision date Description
1.1 16.05.2017The section "GPRS and Communication channels Configurations" was fixed