BEFORE YOU BEGINBEFORE YOU BEGIN

ROUGHING-IN DIMENSIONSROUGHING-IN DIMENSIONS

NOTES

�

�

�

�

�

Use these instructions for above-counter installation.Please follow the instructions that apply to yourinstallation.You can choose between a wall-mount or countertopfaucet installation, depending upon the setting and stylingyou desire. We recommended a wall-mount faucet.Prior to installation, unpack the new lavatory and carefullyinspect it for damage. Return the lavatory to its protectivecarton until you are ready to install it.All information in these instructions is based upon thelatest product information available at the time ofpublication. Kohler China reserves the right to makechanges in product characteristics, packaging, oravailability at any time without notice.These instructions contain import care, cleaning, andwarranty information please leave these instructions forthe consumer.

� Kohler lavatory is made according to American NationalStandard that it can match the American lavatory fittings.Any other lavatory fittings may not fit for kohler lavatory.

�

�

�

�

�

�

-1-

Roughing-In Notes

Fixture dimensions are nominal and conform to tolerancesin ASME Standard A112.19.2M. (ASTMEA)112.19.2M

(T) Pop-up drain 229mm. (T) 229mm

(S) 356mm (Based on 305mm riser which may requingcutting).

(S) 356mm 305mm

* Spout must be 127mm long (min.) for adequate clear-ance into lavatory when installed with centerline as shown.

* 127mm ( )

** Spout must be tall enough to clear 76mm rim height andprovide a 25mm air gap per ASME A112.1.2

** 76mm ASME A112.1.225mm

Fig. #11

CONICAL BELL VESSEL

INSTALLATION INSTRUCTIONS

ABOVE-THE-COUNTER VITREOUS CHINA LAVATORY

K-2200T-G

(S)

(T)

3/8" HOT102mm 102mm

3/8" COLD

1-1/4" OUTLET

**76mm

162mm254mm

413mm

OF FITTING*CL

K-2200T-G

1007250-T01-B

528137

�

�

, 2007

Copyright Kohler China Ltd., 2007

TOOLS AND MATERIALS REQUIRED(NOT SUPPLIED)

�

�

�

�

�

�

�

�

�

�

Sealant

Template (supplied)

Safety glasses

Pencil

Scissors

Tape Measure

Hole Saw

Keyhole saw or saber saw

Dill (1/2" dia. Drill bit, or larger)

Screwdriver

( )

�

�

�

�

�

�

�

�

�

�

( )

( 13mm )

-2-

Position the template on the

countertop.

Be sure to

provide sufficient spout overhang into

the lavatory basin. See the roughing-in

notes for minimum spout length

information.

Pay special

attention to the spout and handle fit

clearance when locating the faucet, as

noted below. Use the template to

locate the faucet spout hole centerline

on the countertop. This centerline is

recommended to provide adequate

clearance between the edge of the

lavatory and the spout.

Check for adequate clearance

between the backsplash or wall faucet

spout and handles, and lavatory. We

recommend clearance of at least

25mm between:

The installed lavatory and the

faucet spout

The installed lavatory and the end

of the faucet handles, and

The faucet spout and handles and

the backsplash or wall.

Refer to the faucet installation

instructions for required clearance, and

mark the preferred faucet hole

locations using a soft lead pencil.

Trace the template on the countertop

using a soft lead pencil.

For Wall-mount faucets:

For Countertop Faucets:

�

�

�

NOTE: In china installation will not

have separate backsplash. The back

wall is the "backsplash".

COUNTERTOP INSTALLATIONS

25mm

�

�

�

25mm Min.Clearance

25mm

SpoutCenterline

Backsplash

Cut-out line

Outside Edgeof Lavatory

Fig. #22

1007250-T01-B

For tile, wood, or other porousmaterials, apply waterproof sealantaround the cutout area of thecountertop surface. Follow allmanufacturer's instructions andwarnings. Allow the sealant to drybefore proceeding.

Use a 50/50 mixture of isopropylalcohol and water to clean thecountertop surface around the cutoutarea. Wipe dry with a clean cloth.

: Install the adhesive sealant

when the temperature is at least 10 C.The preferred temperature range to

apply the adhesive sealant is 21 C to

38 C.

Loosely apply the adhesive sealantaround the entire countertop cutout soit is alongside the cutout hole. Adjustthe placement of the sealant beforeremoving the backing material. Cut offany excess seal material. Carefullyremove the adhesive seal backingmaterial.

NOTEo

o

o

50/50

10

21 38

AdhesiveSealant

Fig.#44

Drill the faucet holes.

Install the faucet to the countertop according to the

manufacturer's instructions.

Install the drain to the lavatory according to the installation

instructions included with the drain. Apply a sufficient amount

of clear silicone sealant when you install the drain.

Fig.#33

Kohler

Cut out the opening by carefullyfollowing the pencil line.

Large lavatories are very heavy.Get help lifting the lavatory intoplace.

Temporarily position the lavatory in thecountertop cutout so the "Kohler" logois visible. The logo is located inside thebasin, near the rim, and should bepositioned near the faucet.

Verify proper clearance between thelavatory, faucet, and backsplash.

Remove the lavatory from thecountertop cutout, and return it to itsprotective carton. Do not stand or storethe lavatory on the drain surface.

CAUTION: Risk of personalinjury or product damage.

-3-1007250-T01-B

NutGaskeet

Nut

GasketFig.#6

6

Connect the faucet supply lines.

Connect the drain assembly.

Open the faucet valves, and check for

leakage.

Clean up with a non-abrasive cleaner.

IMPORTANT CONSUMER INFORMATIONIMPORTANT CONSUMER INFORMATION

CLEANING YOUR VESSELS LAVATORY

Keep your vessels lavatory looking new by rinsing it out

thoroughly after each use. Do not regularly use abrasives on

the lavatory surface, as this will eventually scratch and dull

the surface. For stubborn stains, abrasives may be used

sparingly.

THIS TAG IS FOR REMOVAL BYHOMEOWNER ONLY!

Treat your decorative product just as you would treat your finechina. The best way to clean it is to use warm water and patdry with a cotton cloth or soft sponge. use bristlebrushes or abrasive-backed sponges. They will scratch thedecorative surface.

For occasional cleaning of stubborn deposits, use ONLY thefollowing cleaners: apply the cleaner, wipe gently,

. Pat dry or wipe gently with acotton cloth.

DO NOT

rinse offany residue immediately

USE & CAREUSE & CARE

-4-

CAUTION: Risk of personal

injury or product damage.

Large lavatories are very heavy.

Get help lifting the lavatory into

place.

Note the location of the "Kohler" logo.

The lavatory should be installed so the

logo is visible after installation.

Carefully position the lavatory in the

cutout, and press down firmly.

Fig.#55

Kohler Logo

Kohler

1007250-T01-B