congratulations on owning your new nautica watch … · congratulations on owning your new nautica...

CONGRATULATIONS ON OWNING YOUR NEWNAUTICA WATCH DEVELOPED FROM ADVANCED

ELECTRONICS TECHNOLOGY,THE MOVEMENT IS MANUFACTURED FROM THE

BEST QUALITY COMPONENTS AND POWERED BY ALONG LIFE BATTERY.

NAUTICA watches have been developed with the highest attentionto quality, function and detail, as befits the NAUTICA tradition.Please read the following instructions carefully to fully understandall of the functions of your finely crafted timepiece.

WATER-RESISTANCEIf your watch is water-resistant, it will be indicated on the watch face oron the caseback.• 50 Meter Water-Resistant watch withstands water pressure to 86p.s.

i.a. (equals immersion to 164 feet or 50 meters below sea level) anddust as long as crystal, crown and case remain intact.

• 100 Meter Water-Resistant watch withstands water pressure to 160p.s.i.a. (equals immersion to 328 feet or 100 meters below sea level)and dust as long as crystal, crown and case remain intact.

• 200 Meter Water-Resistant watch withstands water pressure to 320p.s.i.a. (equals immersion to 656 feet or 200 meters below sea level)and dust as long as crystal, crown and case remain intact.NOTE: CROWN MUST BE SCREWED INTO THE CASE

PROTRUSION TO ASSURE WATER RESISTANCE.

INDIGLO® NIGHT-LIGHTIf your watch has “INDIGLO” on the dial, your watch is equippedwith the INDIGLO Night-Light. To activate this feature, depress thecrown or the pusher on the left side of the watch to illuminate theentire dial for easy reading during nighttime or low light conditions.Light will appear immediately.Your NAUTICA watch featuring INDIGLO Night-Light contains apatented electroluminescent technology (U.S. Patent Number 4,527,96 and 4,775,964). The INDIGLO Night-Light illuminates the entirewatch lens with a uniform bright light that offers superior readabilityin all low light and nighttime conditions. Simply press the appropriatebutton to activate.WARNING: DO NOT PRESS THE BUTTON UNDER WATER ASTHE WATCH WILL NOT RETAIN WATER RESISTANCE.INDIGLO is a registered trademark of Indiglo Corporation.

BATTERYBattery contains small amount of mercury. Please recycle or disposeof properly.

SCREW-IN SETTING CROWN

Some deep-depth water-resistant watches require the setting crown tobe screwed in to ensure water-resistant. If your Nautica watch has atransparent sticker at back of the case back (diagram above) pleaseunscrew the crown before setting your watch, and the crown must bescrewed in after setting the watch.

To screw in, push in the crown firmly against the thread protrusion andhold it in while turning the crown clockwise. Continue to screw in thecrown light until it is tight .

ATTENTION This is a screw down crown

Do not pullPlease read instruction

booklet before operation

SCREW-IN SETTING CROWN STICKER

ELAPSED TIME RINGIf your watch is equipped with a rotatable outer dial with numbers andindicators, this Elapsed Time Ring may be used to indicate the length oftime remaining for an activity or the starting time of an activity.TIME REMAINING - set the outer ring so that the traingle is pointing tothe time the activity is to end.STARTING TIME - set the triangle on the time the activity is to begin.

TACHYMETERA tachymeter measures the speed at which the wearer has traveledover a measured distance, i.e., a measured mile on the highway. Forexample, start the chronograph when you pass the starting point andstop it when you pass the finish. You can then read your speed in unitsper hour off the tachymeter scale.

BAND ADJUSTMENTTo disconnect band from clasp, press in end of spring bar(use pin or small paper clip) and separate link band fromclasp as illustrated.

To reassemble band to clasp, place spring bar in band and place end ofspring bar into desired hole in clasp. Press opposite end of spring bar inand slide into clasp and position so tip snaps into corresponding hole.

11

Note: Crown position “A” & “B”Note: Pusher “A” (Top Right), “B” (Bottom Right)Note: 12 O’clock eye “STOPWATCH 1/20 SEC elapsed”Note: 9 O’clock eye “SEC elapsed”Note: 6 O’clock eye “STOPWATCH HOUR/MIN elapsed”

This Chronograph watch has 3 functions:TIMECALENDARSTOPWATCH

CHRONOGRAPH MODELS

STOPWATCH MINUTES HANDSTOPWATCH HOUR HAND

SMALL SECOND HANDPUSHER “A”

STOPWATCH 1/20SEC. HAND

STOPWATCH SECOND HAND

CROWN POSITION

A B C

YM92

PUSHER “B”

12

TIMETo set the time:1. Pull crown to position “C”2. Turn crown clockwise / counter clockwise to correct time3. Push crown to position “A”

CALENDARTo set the calendar:1. Pull crown to position “B”2. Turn crown clockwise to correct calendar3. Push crown to position “A”

STOPWATCHThe stopwatch is capable of measuring:– 1/20 seconds elapsed up to one second (top eye)– Minutes elapsed up to 30 minutes (bottom eye)– Hour elapsed up to 12 hours (bottom eye)– Seconds elapsed up to one minute (middle eye)

Before using the stopwatch, reset the stopwatch handsTo the “12” and “0” position.

STANDARD STOPWATCH MEASUREMENT:1. Press pusher “A” to start timing2. Press pusher “A” to stop timing3. Press pusher “B” to reset

13

ACCUMULATED ELAPSED TIME MEASUREMENT:1. Press pusher “A” to start timing2. Press pusher “A” to stop timing3. Press pusher “A” to restart timing4. Press pusher “A” to stop 2nd timing5. Press pusher “B” to reset

Example of using split time measurement for two runnersTwo runners can be timed simultaneously; the first runner’s time can be recordedwhile the second runner’s time will continue to be accumulated until he finishes.

SPLIT TIME MEASUREMENT:1. Press pusher “A” to start the timing of the first runner2. Press pusher “B” to stop and record the timing of the first runner. (Once

pusher B is activated, even though the stopwatch 1/20 sec. hand and the bigstopwatch sec. hand stop on the dial, the stopwatch still continues to timeinternally.)

3. Press pusher “B” to start the timing of the second runner. The stopwatch sec.hand will jump to show internal accumulated time and to carry on timing ofthe second runner.

4. Press pusher “A” to stop the timing of the second runner and record the time5. Press pusher “B” for third time to reset, all stop watch hands will return to 12

o’clock position.

14

TO ADJUST STOPWATCH HANDS:1. Pull crown to “C” position2. Press pusher “A” for 2 seconds3. Press pusher “B” to “0” setting for the 1/20 sec. hand. If the hand is not at “0”

or “12” position, then, press pusher “B” repeatedly, until the hand moves byeach intervaI and returns to “0” or “12” position

4. Press pusher “A” for 2 seconds5. Press pusher “B” to “0” setting for the stopwatch sec. hand. If the hand is not

at “0” or “12” position, then, press pusher “B” repeatedly, until the hand movesby each intervaI and returns to “0” or “12” position

6. Press pusher “A” for 2 seconds7. Press pusher “B” to “0” setting for the stopwatch min. / hour hand. If the hand

is not at “0” or “12” position, then, press pusher “B” repeatedly, until the handmoves by each intervaI and returns to “0” or “12” position

8. Push crown to “A” position after the adjustments of all stopwatch handsNote: Please make sure that the stopwatch is stop and reset before adjusting

15

2, 6, 10 Three – Eye Chronograph with AlarmNote: Crown position “A”, “B” & “C”Note: Pusher “A” (Top), “B” (Bottom)Note: Left eye “30 minute totalizer”Note: Right eye “second hand”Note: Bottom eye “day calendar”

This chronograph has 4 functions:TIME, DAY & DATE, STOPWATCH, ALARM


A B C

CROWN POSITION

PUSHER “B”PUSHER “C”

PUSHER “A”

ALARM

HOUR HAND

CHRONOGRAPHHAND 1/5 SECOND

MINUTE HAND8154/220

16

DAY & DATE CALENDARTo set the day calendar:1. Pull crown to position “C”2. Turn crown clockwise / counter clockwise to correct day (bottom eye)3. Push crown to position “A”

To set the date calendar:1. Pull crown to position “B”2. Turn crown clockwise to correct date (window @ 4)3. Push crown to position “A”

Note: It is not possible to correct the date between 9 p.m. and 0:30 a.m.

STOPWATCHThe stopwatch is capable of measuring:1. Minutes (up to 30 minutes)2. Chronograph hand 1/5 second

Before using the stopwatch, reset the stopwatch hands to the “12” position bypressing pusher “B”. If the stopwatch hands reset improperly, reset the hands asfollows:

To reset the stopwatch hands:1. Press pushers “A” and “B”2. Press pusher “B” intermittently until the left eye hand is reset to “30”3. Press pusher “A” intermittently until the chronograph hand resets to “60”4. Press pusher “A” and “B”

Note: PRESSING & HOLDING either pusher “A” or “B” will cause the handsto continue to move until the pusher is released.

17


ACCUMULATED ELAPSED TIME MEASUREMENT:1. Press pusher “A” to start timing2. Press pusher “A” to stop timing3. Press pusher “A” to restart timing4. Press pusher “A” to stop 2nd timing etc, etc.5. Press pusher “B” to reset

SPLIT TIME MEASUREMENT:1. Press pusher “A” to start timing2. Press pusher “B” to split3. Press pusher “B” to begin again4. Press pusher “A” to stop5. Press pusher “B” to reset

TIMING 2 EVENTS / COMPETITORS:1. Press pusher “A” to start timing of 1st event2. Press pusher “B” to stop timing of 1st event

Stopwatch continues to run internally3. Press pusher “A” to stop timing of 2nd event4. Press pusher “B” to view time of 2nd event5. Press pusher “B” to reset

18

ALARMTo set the alarm:1. Pull crown to position “B”2. Turn crown counter clockwise to set alarm (colour hand)3. Push crown to position “A”

To activate the alarm:1. Press pusher “C” to activate the alarm. Watch beeps twice2. Press pusher “C” again to de-activate alarm. Watch beeps once3. To stop alarm, press pusher “C” once

19

A B C

CROWN POSITION

8161/202

PUSHER B

PUSHER A

MINUTE

SECONDS

DATE

2, 6, 10 THREE - EYE CHRONOGRAPH

Note: Crown position “A”, “B” & “C”Note: Pusher “A” (Top), “B” (Bottom)Note: Left eye “minute totalizer”Note: Right eye “small second”Note: Center eye “date indicator”

This Chronograph watch has 3 functions:TIMECALENDARSTOPWATCH

20



STOPWATCHThe stopwatch is capable of measuring:1. 1 minute elasped up to 30 minutes (left eye)2. Chronograph hand 1/5 second

Before using the stopwatch, reset the stopwatch hands To the “60” position by meansof pusher “B”. If stopwatch Hands move improperly, reset the hands as follow:

To reset stopwatch hands:1. Press pusher “A” & “B”2. Press pusher “B” intermittently until the left eye hand is reset to “0”3. Press pusher “A” intermittently until the chronograph hand reset to “60”4. Press pusher “A” & “B”

NOTE: PRESSING & HOLDING either pusher “A” or “B” will Cause the handsto continue to move until the pusher is released.

21



SPLIT TIME MEASUREMENT:1. Press pusher “A” to start timing2. Press pusher “B” to split3. Press pusher “B’ to begin again4. Press pusher “A’ to stop5. Press pusher “B’ to reset

TIMING 2 COMPETITORS:1. Press pusher “A” to start timing of 1st event2. Press pusher “B” to stop timing of 1st event stopwatch continues to run

internally.3. Press pusher “A” to stop timing of 2nd event4. Press pusher “B” to view time of 2nd event5. Press pusher “B” to reset

22

2, 6, 10 Three – Eye Chronograph with AlarmNote: Crown position “A”, “B” & “C”Note: Pusher “A” (Top), “B” (Bottom)Note: Left eye “30 minute totalizer”Note: Right eye “second hand”Note: Bottom eye “day calendar”

This chronograph has 4 functions:TIME, DAY & DATE, 5 HOUR CHRONOGRAPH, ALARM


4

5

4

3 2

1

A B C

CROWN POSITION

PUSHER “B”PUSHER “C”

PUSHER “A”

ALARM

HOUR HAND


MINUTE HAND8154/221

23

DAY & DATE CALENDARTo set the day calendar:1. Pull crown to position “C”2. Turn crown clockwise / counter clockwise to correct day (bottom eye)3. Push crown to position “A”

To set the date calendar:1. Pull crown to position “B”2. Turn crown clockwise to correct date (window @ 4)3. Push crown to position “A”Note: It is not possible to correct the date between 9 p.m. and 0:30 a.m.

STOPWATCHKey Features of Stopwatch Mode:1. This is a stopwatch for timing long

hours chrono function.2. The dial is designed with 5 hours

chrono indicator. Please see thediagram.

3. It times speed at 1/5 sec intervals.4. The split function only available at

the first thirty minutes.5. After the initial thirty minutes, the

stopwatch will proceed with the“Hour Chrono Mode” to save thepower consumption. (Be ware, inthis mode, the big sec handmoves very slowly and looks likeas it has stopped.)

A B C

CROWNPOSITION

PUSHER“B”

PUSHER“C”

PUSHER“A”

3 hour 2 hour

5 hour

4 hour1 hour

24

TO START THE STOPWATCH:• Push pushers “A”, the big sec will start counting at intervals of 1/5 sec for the

first thirty minutes.

TO STOP THE STOPWATCH:• Push the pusher “A” again to stop timing.

TO RESET THE STOPWATCH:• Push pushers “B”, to reset the stopwatch. Both the big sec. hand and small

hand at the small eve at 10 o’clock position will go back to 12 o’clock position.

STOPWATCH IN “HOUR CHRONO MODE”After the big sec hand has run for thirty minutes, the watch will stay with the“hour chrono mode”. The big sec hand jumps to the hour indicator to carry onwith the timing. (Be ware, in this mode, the big sec hand moves very slowly andlooks like as it has stopped.)

TO STOP THE STOPWATCH FOR LONG HOURS CHRONO MEASUREMENT:Push pusher “A” will stop the stopwatch. The big sec. hand stops at the hourindicator on the dial to show how many hours the stopwatch has timed. At thesame instance, the small eye at 10 o’clock position also shows the minutes timing.Then, press pusher “B” the big sec. hand will jump to show the seconds timing.

TO RESET THE STOPWATCH:Push the pusher “B” to reset the stopwatch. Both the big sec. hand and smallhand at the small eye at 10 o’clock position will go back to 12 o’clock position.

TO ADJUST STOPWATCH HANDS:1. Push the pushers “A” and “B” simultaneously and hold for 2 seconds to activate

the reset mode.

25

2. Push the pusher “B” to reset the small hand of the eve at 10 o’clock position.After the pusher is pushed, the small sec hand will reach the “30” positionexactly.

3. Push the pusher “B” to reset the big sec. hand. When it moves close to the11 o ‘clock position, adjust it by pushing the button sec by sec until it reachesthe 12 o’clock position exactly.

4. Push the pushers “A” and “B” simultaneously and hold for 2 seconds to de-activate the reset mode.

SPLIT TIME MEASUREMENT FOR TIMING TWO RUNNERS:1. Push the pusher “A” to start the timing of both runners.2. Push the pusher “B” to split, the big sec. hand stops to show timing of the

first runner, but the timing continues internally.3. Push again the pusher “B” to resume timing, and the hand moves quickly to

make up the elapsed time.4. Push the pusher “A” to indicate the timing of the second runner.

ALARMTo set the alarm:1. Pull crown to position “B”2. Turn crown counter clockwise to set alarm (colour hand)3. Push crown to position “A”

To activate the alarm:1. Press pusher “C” to activate the alarm. Watch beeps twice2. Press pusher “C” again to de-activate alarm. Watch beeps once3. To stop alarm, press pusher “C” once

26

Note : Crown position “A” “B” and “C”Note : Pusher “A” (Top right) “ B” (Bottom Right)Note : 6 o’ clock eye - Hours elapsed up to 12 hoursNote : 9 o’clock eye - Minutes elapsed up to 30 minutesNote : 3 o’clock eye - Permanente second hand

This Chronograph watch has 3 functions :TIME, CALENDAR, STOPWATCH

TIMETo set the time :1. Pull crown to position “C”2. Turn crown clockwise / counter clockwise to correct time.3. Push crown back to position “A”

A B C

CROWN POSITION

PUSHER “B”

PUSHER “A”

5030DDATE

MINUTE CHRONO HAND

HOUR CHRONO HAND

PERMANENTSECOND HAND

STOPWATCHSECOND HAND

27

CALENDARTo set the Calendar1. Pull crown to position “B”2. Turn crown clockwise to correct calendar3. Push crown back to position “A”

STOPWATCHThis stopwatch is capable of measuring :Chrono Hours elapsed up to 12 hours ( 6 o,clock eye)Chrono Minutes elapsed up to 30 minutes ( 9 o,clock eye )Stopwatch Second up to 1 minute. ( Big second hand )

Before using the stopwatch, reset stopwatch chrono hands to the “12” and “0”position

STANDARD STOPWATCH MEASUREMENT1. Press pusher “A” to start timing2. Press pusher “A” again to stop timing3. Press pusher “B” to reset

Accumulated Elapsed Time Measurement1. Press pusher “A” to start timing2. Press pusher “A” again to stop timing3. Press pusher “A” to restart timing4. Press pusher “A” again to stop second timing5. Press pusher “B” to reset

28

SPLIT TIME MEASUREMENTExample of using split time measurement for two runners. Two runners can betimed simultaneously; the first runner’s time can be recorded while the secondrunner’s time will continue to be accumulated until he finishes.

1. Press pusher “A” to start the timing of the first and second runner2. Press pusher “B” to stop and record the timing of the first runner. ( Once pusher “B” is activated, even though the chrono minute hand and the

big stopwatch sec. hand stop on the dial, the stopwatch still continues tointernally.)

3. Press pusher “B” to catch up the timing of the second runner. The stopwatchsec. hand will jump to show internal accumulated time and to carry on timingof the second runner.

4. Press pusher “A” to stop the timing of the second runner and record the time.5. Press pusher “B” for third time to reset, all stopwatch chrono hands will return

to “12” and “0” position.

CORRECTIVE MODE FOR STOPWATCH CHRONO HANDS1. Pull crown to position “C”2. Press pushers “A” and “B” simultaneously for at least 2 seconds.3. The big stopwatch sec hand rotates by 360 degree to activate corrective

mode

TO ADJUST THE BIG SEC. STOPWATCH HANDIf it is not located at “12” or “0” position, either press pusher “A” continuously orrepeatedly until the hand moves by each interval and returns to “12” and “0”position.

29

After finish adjusting big sec. stopwatch hand, press crown back toposition “A” to terminate the adjustment.

TO ADJUST THE HOUR CHRONO HANDAfter activate the corrective mode; if the hour chrono hand in not located at “12”or “0” position, press pusher “B” once to activate the corrective mode of the hourchrono hand. Press pusher “A” continuously or repeatedly until the hand movesby each interval and returns to “12” and “0” position.Press crown back to position “A” to terminate the adjustment.

TO ADJUST THE MINUTE CHRONO HANDAfter activate the corrective mode; if the minute chrono hand in not located at“12” or “0” position, press pusher “B” twice to activate the corrective mode of theminute chrono hand.Press pusher “A” continuously or repeatedly until the hand moves by each intervaland returns to “12” and “0” position.Press crown back to position “A” to terminate the adjustment.

Once finish adjusting all stopwatch chrono hands, press crown back to “A” positionto terminate adjustment.

30

Note: Crown position "A" "B" &"C"Note: Pusher "A" ( Top Right), Pusher 'B" ( Bottom Right)Note: 3 o'clock eye - 24 hour handNote: 6 o'clock eye - second handNote : 9 o'clock eye - stopwatch minute hand

This Chronograph watch has three functions :TIME, CALENDAR, STOPWATCH

TIMETo set the time:1. Pull crown to position "C"2. Turn crown clockwise / counter clockwise to correct time3. Push crown to position "A"

A B C

CROWN POSITION

PUSHER “B”

PUSHER “A”

OS20DATE

STOPWATCH MINUTEHAND

SECOND HAND

24 HOUR HAND

STOPWATCHSECOND HAND

31

Remarks: When crown is pushed back to position "A," small second handbegins to run.

CALENDARTo set the calendar1. Pull crown to position "B"2. Turn crown counter-clockwise to set calendar3. Push crown to position "A"

STOPWATCHThe stopwatch is capable to measure and display time in 1/1 second united upto maximum of 59 minutes 59 seconds.

1. Press pusher "A" to start timing2. Press pusher "A" again to stop timing3. Press pusher "B" to reset

CORRECTING STOPWATCH HANDIf after resetting the stopwatch second hand and found that it is not at the "12"or "0" position, correct it as follows:

1. Pull crown to "C" position2. Press pusher "A" continuously, the stopwatch second hand will be advanced

rapidly until it gets closely to the "12" position. Then, press pusher "A"repeatedly, the stopwatch second hand will be moved by interval until itreturns to "12" position.

3. Push crown to position 'A"

32

Note: Crown Position “A” “B” & “C”Note: Pusher “A” (Top right), Pusher “B” (Bottom Right )Note: 12 o’clock eye chrono minute handNote: 6 o’clock permanent second hand

This Chronograph watch has 3 functionsTIME, CALENDAR, STOPWATCH

TIMETo set the time :1. Pull crown to position “C”2. Turn crown counter clockwise to correct time3. Push crown to position “A”

OS11

MINUTES HAND

PERMANENTSECOND HAND

CROWN POSITION

A B CSTOPWATCHSECOND HAND

PUSHER “A”

DATE

PUSHER “B”

HOUR HAND

STOPWATCHMINUTE HAND

33

CALENDARTo set the calendar1. Pull out the crown to position B.2. Turn crown counter clockwise to correct calendar3. Push in the crown to position A.

STOPWATCHThis watch is capable to measure and display 1 second unit up to maximum of60 minutes1. Press pusher “B” to enter to chrono mode.2. Press pusher “A” to start the timing3. Press pusher “A” again to stop timing4. Press pusher “B” to reset

CORRECTING STOPWATCH HANDS TO “12” OR “0” POSITION1. Pull crown to position “B”2. Press pusher "A" until both second and minute chrono hands return to "12" or

"0" position.3. Once the hands have been corrected, reset the time and press crown to

position “A”Note:Do not push crown to position “A” while correcting chrono hands

34

Note : Crown position “A” “B” and “C”Note: Pusher “A” ( Top Right ), “B” ( Bottom Right)Note: 12 o’clock eye - Stopwatch minute handNote : 6 o’clock eye - Second hand

This Chronograph watch has three functions :TIME, CALENDAR, STOPWATCH


CROWN POSITION

A B C

PUSHER “A”

PUSHER “B”

YM91

STOPWATCHMINUTE HAND

SECOND HAND


35


STOPWATCHThis stopwatch is capable of measuring :– 1/5 second elapsed up to 60 minutes– After 60 minutes, it will start counting again from “0” repeatedly up to 12 hours

Before using the stopwatch, reset the stopwatch handsTo the “12” and “0” position.



Example of using split time measurement for two runnersTwo runners can be timed simultaneously; the first runner’s time can be recordedwhile the second runner’s time will continue to be accumulated until he finishes.

36

SPLIT TIME MEASUREMENT:1. Press pusher “A” to start the timing of the first runner2. Press pusher “B” to stop and record the timing of the first runner. (Once

pusher B is activated, even though the stopwatch 1/20 sec. hand and the bigstopwatch sec. hand stop on the dial, the stopwatch still continues to timeinternally.)

3. Press pusher “B” to start the timing of the second runner. The stopwatch sec.hand will jump to show internal accumulated time and to carry on timing ofthe second runner.

4. Press pusher “A” to stop the timing of the second runner and record the time5. Press pusher “B” for third time to reset, all stop watch hands will return to 12

o’clock position.

TO ADJUST STOPWATCH HAND1. Pull crown to position “C”2. Press pusher “A” for 2 seconds, the stopwatch minute hand turns a full cycle3. Press pusher “B” repeatedly to set stopwatch minute hand to “0” position.4. Press pusher “A” again for 2 seconds, the stopwatch sceond hand turns a full

cycle5. Press pusher “B” repeatedly to set stopwatch second hand to “0” position.6. Push crown to position “A”

Remarks :This is suggested to check the hour and minute hand to ensure it is correctbefore push the crown back to position “A”

LIMITED WARRANTYThe Basic Coverage: This NAUTICA watch (but not any battery, crystal, case, bandor strap) is warranted to the owner for a period of FIVE YEARS from the date ofpurchase against defects In manufacture by Nautica Watches - not by the dealerfrom whom the watch was purchased.

What Nautica Watches Will Do:If this watch develops such a defect within the five year period it will be repaired (i.e., a new or thoroughly reconditioned and inspected movement will be installed) orreplaced (a watch of equal value and similar appearance will be supplied) at ouroption, provided it is returned with a $7.50 check or money order to cover costs ofpostage, handling and service, and you provide proof of purchase and date ofpurchase.

This Limited Warranty Does Not Cover:1) Nautica Watches will not repair defects related to servicing not performed by

Nautica Watches.2) Nautica Watches will not provide any warranty service if your watch shows

evidence that it has been tampered with, misused, abused, or altered; forexample:• moisture damage sufficient to affect the proper function of the watch;• damage to the case; or• visible cracking of the crystal.

3) Nautica Watches reserves the right to charge you for a replacement battery, ifthe battery in your watch is depleted. No additional charge will be madeunless the five year warranty period has expired or servicing is necessary forreasons beyond our control, in which case a moderate charge will be made.

4) NAUTICA WATCHES IS NOT LIABLE FOR INCIDENTAL, SPECIAL ORCONSEQUENTIAL DAMAGES. Some states do not allow the exclusion orlimitation of incidental, special or consequential damages, so the above exclusionor limitation may not apply to you.

Your Rights Under Implied Warranties and State Law: THIS LIMITEDWARRANTY IS IN LIEU OF ALL OTHER EXPRESSED WARRANTIES,OBLIGATIONS OR LIABILITIES. NAUTICA WATCHES LIMITS THE DURATIONOF ANY WARRANTY IMPLIED BY STATE LAW, INCLUDING BUT NOT LIMITEDTO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR APARTICULAR PURPOSE, TO FIVE YEARS FROM THE DATE OF ORIGINALPURCHASE. Some states do not allow limitations on how long an implied warrantylasts, so the above limitation may not apply to you. This warranty gives youspecific legal rights, and you may also have other rights which vary from state tostate.

Care of Your Watch:• Avoid exposing your watch to water, steam, or other forms of moisture, if your

watch is not water-resistant.• If the crystal becomes damaged, have it replaced at once to avoid damage to

the movement.• When your battery is depleted, have it replaced promptly. The particular type

of battery required is indicated on your caseback.

Service of Your Watch:If your NAUTICA watch should ever need servicing, send it to: NAUTICA HOTLINEWATCH SERVICECALLANEN INTERNATIONAL145 Woodward Avenue, Norwalk, CT 06854Attn: The Repair DepartmentBecause of possible loss, we recommend insuring your watch, return receiptrequested, when using the mails. If you do not obtain a receipt within a reasonabletime, start a tracer through the originating post office. NEVER INCLUDE A SPECIALWATCHBAND OR ANY OTHER ARTICLE OF PERSONAL VALUE IN YOURSHIPMENT. PLEASE NOTE THAT WE MAY SUBSTITUTE A WATCH OF EQUALVALUE AND SIMILAR APPEARANCE FOR YOURS ON BOTH IN-WARRANTYAND OUT-OF-WARRANTY REPAIRS.

congratulations on owning your new nautica watch … · congratulations on owning your new nautica...

Documents