conformity packet 1680.2 4 - green electronics council€¦ · 7/16/2018 · 1680.2 4.5.2.1 this...
TRANSCRIPT
Conformity Packet 1680.2 4.5
Conformity Guidance 1680.2: 4.5.1.1 Conformity Guidance 1680.2: 4.5.2.1 Conformity Guidance 1680.2: 4.5.2.2 Conformity Guidance 1680.2: 4.5.3.1 Conformity Guidance 1680.2: 4.5.3.2 Conformity Guidance 1680.2: 4.5.4.1
1680.2 4.5
Conformity Guidance 1680.2: 4.5.1.1Required: ENERGY STAR
1680.2 4.5.1.1
Applicable Interpretations,Clarifications, Outcome Reports
Document/Evidence Request Document Review Standards Common Conformity Issues and Details to Remember
EPEAT ClarificationsClarification 9
Outcomes ReportsIE 2013-04
Declare to which version of the ENERGY STAR specifications the product complies
Provide link to the product or product family listing on the U.S EPA ENERGY STAR1 website (or international partners2,3)
OR
Provide analytical test data for the product based on the US ENERGY STAR program requirements
Declaration must be made on the EPEAT Registry at the time of registration.
Specific product or product family must be listed on the website for the latest ENERGY STAR program requirements in the US or international partners2,
The product should fall within the scope of the product types covered by the applicable US ENERGY STAR program requirements. The supporting data should indicate that: (1) the specified US ENERGY STAR Test Method was followed (these can be found in the Program Requirements documents); (2) the calculations were performed accurately; and (3) the product meets the required levels. Test reports must include Power Supply and Power Management and indicate conformance to these. Tests must be performed on the most energy-use intensive configuration in the product family.
The listing on the ENERGY STAR website or analytical tests must have dates prior to the product registration date on EPEAT or new version effective date (as appropriate).
Testing can be performed by non-EPA labs, but they must follow test methods and meet requirements of the current ENERGY STAR specification.
Due to the expiration of the EU-US ENERGY STAR Agreement in 2018, products that are EPEAT registered in the EU may demonstrate conformance to this criterion either by providing their listing to the US ENERGY STAR program which includes the EU country/region it is marketed or sold in, or by providing laboratory reports showing compliance with ENERGY STAR requirements using the country’s voltage specifications.
1 Energy Star specifications for imaging equipment can be found here: https://www.energystar.gov/products/office_equipment/imaging_equipment2ENERGY STAR qualified product listings are only available for products marketed in the United States or countries where Energy Star has an international partner. Products can appear as meeting the EPA ENERGY STAR Requirements in the following countries: US and Canada, European Union, Japan, and New Zealand. Note that many of these websites also include a list of countries in which the qualified product is marketed. This means that the product was tested in accordance with the conditions (voltage/current) for the listed country.
Easy to demonstrate conformance
Updated 7-16-18
Sample Conformity Packet
1680.24.5.1.1: Required– ENERGY STAR
1680.2 4.5.1.1
The following data samples and explanation are intended to illustrate examples of acceptable data. Other types or forms of data may also be acceptable in conformity documentation.
Declaration of compliance to ENERGY STAR version
1680.2 4.5.1.1
Manufacturer must declare the ENERGY STAR specification version to which the product complies. In the event of an ENERGY STAR update, EPEAT
will request manufacturers to update the EPEAT registry with the most current information.
After the implementation date of a new version of ENERGY
STAR , EPEAT requires manufacturers to archive products that no longer comply with the current
version.
Listing on ENERGY STAR website
1680.2 4.5.1.1
https://www.energystar.gov/productfinder/product/certified-displays/details/2268428
Note: If the product is not ENERGY STAR certified, then analytical test data showing conformance with current ENERGY STAR specifications must be provided. See previous table for more information.
Provide a link to the product listing on the EPA ENERGY Star Website. To help the auditor quickly find the listing, consider providing a link to the specific product listing
rather than to the general Energy Star website.
This listing shows the specific product meets the
current ENERGY STAR Specifications in various
countries.
Product XYZ
Conformity Guidance 1680.2: 4.5.2.1Optional: Product specific greenhouse gas emissions – life-cycle assessment
1680.2 4.5.2.1
Applicable Interpretations,Clarifications, Outcome Reports
Document/Evidence Request Document Review Standards Common Conformity Issues and Details to Remember
EPEAT ClarificationsClarification 32Clarification 41
Outcomes ReportsIE 2016-03
Documentation of an LCA analysis or carbon footprint detailing the greenhouse gas emissions of the product.
Documentation must show that a complete cradle-to-grave assessment was conducted for the product, including from raw material extraction through final disposal or end use by the consumer. The documentation must indicate the standard and version number utilized to conduct the assessment (PAS 2050:2008, the GHG Protocol, ISO 14097, or ISO 14040/14044).
EcoLeaf environmental declarations published on the JEMAI website are an example of documentation that indicates conformance for this criterion for certain product categories1. It must be specific to the product. See Clarification 32 for more information.
KEITI Carbon Footprint Program certifications also indicate conformance. They must be product specific. See Clarification 41 for more information.
The assessment may be done for the specific product registered or for a “family” of products that includes the registered product.
1 Product categories that have been found conformant to 4.5.2.1 using JEMAI’s Ecoleaf program include: Electrophotographic Dry Process Photocopier, EP and IJ Printer, and Facsimile (multifunction devices should use the EP and IJ Printer product categories). See Clarification 32 for more details. Other product categories must be reviewed in order to meet this criterion using JEMAI’s EcoLeaf program. Contact GEC if you need additional product categories reviewed.
Somewhat difficult to
demonstrate conformance
Updated 9-28-17
Sample Conformity Packet
1680.24.5.2.1: Optional – Product specific greenhouse gas emissions – life-cycle assessment
1680.2 4.5.2.1
The following data samples and explanation are intended to illustrate examples of acceptable data. Other types or forms of data may also be acceptable in conformity documentation.
LCA for greenhouse gases
1680.2 4.5.2.1
This Product Environmental Information Data Sheet from EcoLeaf is an example of an assessment of the complete cradle-to-grave life-cycle greenhouse gas (GHG) emissions of the product from raw material
extraction through final disposal or end use by the consumer (i.e., the complete product carbon footprint). It identifies the standard utilized to
conduct the assessment (ISO 14025). Additionally, it indicates the product category it was evaluated against, which is one of the PCRs that have been approved by the CDP (see Clarification 32 for more details).
Conformity Guidance 1680.2: 4.5.2.2Optional: Product specific greenhouse gas emissions—third-party verification or making LCA assessment
publicly available
1680.2 4.5.2.2
Applicable Interpretations,Clarifications, Outcome Reports
Document/Evidence Request Document Review Standards Common Conformity Issues and Details to Remember
EPEAT ClarificationsClarification 32Clarification 41
Outcomes ReportsIE 2015-01IE 2014-02
Documentation of the LCA analysis1 or carbon footprint detailing the greenhouse gas emissions of the product.
IF 3rd PARTY VERIFICATION IS DECLARED:
Documentation confirming that the process used to determine results of LCA assessment conducted under 4.5.2.1 were verified by an independent 3rd party.
OR:IF SUMMARY OF RESULTS MADE PUBLICALLY AVAILABLE AND SUBMITTED TO NATIONAL DATABASE Documentation of where summary of results
is available (e.g. company website, company sustainability report, etc).
Documentation of national database where summary was listed with name and credentials of person(s) responsible for submitting entry to the LCA/LCI database.
Document should identify the standard (e.g. PAS 2050:2008) and version number to which the assessment is compliant. The assessment should meet all the specifications included in 4.5.2.1 criterion text and must detail greenhouse gas emissions of the product.
Document must show that 3rd party verification was carried out in conformance with ISO 14064 and ISO 14065, or another method referenced in 4.5.2.1. It must include credentials and contact information of third party verifier and be dated within 2 months of product registration.
Documentation must prove that the summary is publically available
National database must improve life cycle data quality by accepting primary or secondary data. Name and credentials of responsible person submitting into the LCA/LCI database must be included. Submission must be made within 2 months of product registration.
EcoLeaf environmental declarations published on the JEMAI website meet the requirements for 3rd party verification and for making the assessment publically available for certain product categories2. They do not show conformance for submitting the analysis to a national database. See Clarification #32 for more information.
You must declare on the registry whether the product was 3rd party verified OR if summary of results was made publically available and submitted to a national database. You MUST be conformant to one of those options but MAY be conformant to both.
Manufacturers must either 3rd party verify the assessment or submit assessment to a national database within two months of product registration
This criterion is product specific! If the product type is not specifically listed in
Clarification #32, Manufacturers are welcome to provide evidence that the Product Category Rules for the missing product type meet all the requirements of 4.5.2.2.
1 The requirements for the LCA analysis for 4.5.2.2 reference the criterion text of 4.5.2.1. 4.5.2.1 criterion text: Manufacturers shall conduct an assessment of the complete cradle-to-grave life-cycle greenhouse gas (GHG) emissions of the product from raw material extraction through final disposal or end use by the consumer (i.e., the complete product carbon footprint) using PAS 2050:2008, the GHG Protocol, ISO 14067, or ISO 14040/14044/14025.2Product categories that have been found conformant to 4.5.2.2 using JEMAI’s Ecoleaf program include: Electrophotographic Dry Process Photocopier, EP and IJ Printer, and Facsimile. See Clarification 32 for more details. Other product categories must be reviewed in order to meet this criterion using JEMAI’s EcoLeaf program. Contact GEC if you need additional product categories reviewed.
Somewhat difficult to
demonstrate conformance
Updated 9-28-17
Sample Conformity Packet
1680.24.5.2.2 Optional Product specific greenhouse gas emissions—third-party verification or making LCA assessment publicly available
1680.2 4.5.2.2
The following data samples and explanation are intended to illustrate examples of acceptable data. Other types or forms of data may also be acceptable in conformity documentation.
LCA for Greenhouse Gases3rd Party Verified
1680.2: 4.5.2.2
This Product Environmental Information Data Sheet from EcoLeaf is an example of an assessment of the complete cradle-
to-grave life-cycle greenhouse gas (GHG) emissions of the product from raw material extraction through final disposal or end use by the consumer (i.e., the complete product carbon
footprint).
3rd Party Verified Contact, Credentials, and ISO standard
1680.2 4.5.2.2
Dated within 2 months of product registration with
EPEATThird party verification was conducted
according to ISO 14025. Contact information of third party verifier is
included. Credentials are supported by JEMAI’s publically available program
manual which details verified credentials.
Declaration in Registry
1680.2 4.5.2.2
Mark only the option that applies. If you are conformant to both, mark both options, but in that case you
must submit conformity documentation for both.
* Note that most manufacturers only conform to one of these options.
Conformity Guidance 1680.2: 4.5.3.1Required: Standby power level ≤ 1 W and disclosure
1680.2 4.5.3.1
Applicable Interpretations,Clarifications, Outcome Reports
Document/Evidence Request Document Review Standards Common Conformity Issues and Details to Remember
No EPEAT Clarifications or IEEE Interpretations Available
Outcomes ReportsIE 2015-03IE 2013-04
Test report indicating standbypower level1.
Product documentation indicating how standby power supply level is achieved.
Test must be conducted by IEC 62301 or therelevant Energy Star method. It must indicate the standby power level is ≤ 1 W.
Product documentation must indicate how standby power supply level is achieved and demonstrate the standby power level is ≤ 1 W.
If the Energy Start test method is used, the test report should correlate with the current version of ENERGY STAR.
Providing a current Energy Star listing would also be acceptable instead of a test report as long as the Energy Star listing shows the standby power level is ≤ 1W.
1 The standby power level, usually occurs in off mode, but can occur in ready or sleep Mode.
Easy to demonstrate conformance
Updated 10/18/18
Sample Conformity Packet
1680.24.5.3.1: Required– Standby power level ≤ 1 W and disclosure
1680.2 4.5.3.1
The following data samples and explanation are intended to illustrate examples of acceptable data. Other types or forms of data may also be acceptable in conformity documentation.
Test report indicating standby power level
1680.2 4.5.3.1
This excerpt from an Energy Star test report indicates the method utilized is IEC 62301 and that the power standby
level is ≤ 1 W.
Product documentation indicating how standby power standby level is achieved
1680.2 4.5.3.1
This product specification sheet indicates the power off mode
(standby) is less than 0.1 W, which is lower than the criterion threshold.
This product information explains how the standby power level is achieved.
Conformity Guidance 1680.2: 4.5.3.2Optional: Auto standby capability
1680.2 4.5.3.2
Applicable Interpretations,
Clarifications, Outcome Reports
Document/Evidence Request Document Review Standards Common Conformity Issues and
Details to Remember
No EPEAT Clarifications or IEEE
Interpretations Available
Outcomes Reports
IE 2013-04
Provide documentation indicating how the auto standby power level1 function operates. Provide information where the documentation is publically available.
Provide evidence that standby power level function is enabled at product shipment (e.g. specification);
OR
If it is inappropriate for the product to have standby power level function enabled, provide evidence that the capability is included as an option that may be accessed by the user.
Documentation must indicate how the auto standby power function operates. The documentation must be publically available (e.g. on manufacturer website).
Evidence must indicate that the standby power level function is enabled at product shipment.
Documentation must indicate that the auto standby option can be accessed by the user. It must also demonstrate that a 1 W or less standby power level is inappropriate for the product’s use.
Information about how auto standby power level functions must be publically available.
An example of a case where it would be inappropriate for the product to have standby power level function enabled is a stand alone fax machine.
Somewhat difficult to
demonstrate conformance
1 The standby power level, usually occurs in off mode, but can occur in ready or sleep Mode.
Sample Conformity Packet
1680.24.5.3.2: Optional– Auto standby capability
1680.2 4.5.3.2
The following data samples and explanation are intended to illustrate examples of acceptable data. Other types or forms of data may also be acceptable in conformity documentation.
Publically available information indicating how auto standby functions
1680.2 4.5.3.2
This product manual is available online according to the model. This excerpt indicates how the auto sleep mode (auto standby power level) can be enabled by
the user.
Printer XYZPrinter 123Printer ABC
Evidence that auto standby is enabled at product shipment
1680.2 4.5.3.2
This excerpt from a product specification
document indicates that the auto sleep time (auto
standby power level) is enabled as the default at
the time of shipment.
Conformity Guidance 1680.2: 4.5.4.1Optional: Default to automatic duplex printing
1680.2 4.5.4.1
Applicable Interpretations,
Clarifications, Outcome Reports
Document/Evidence Request Document Review Standards Common Conformity Issues and
Details to Remember
No EPEAT Clarifications
Available
Outcomes Reports
IE 2013-04
Provide product documentation demonstrating that automatic duplex printing is operational. Products that do not have automatic duplex printing capability can declare N/A on the EPEAT Registry.
Provide information where the above referenced product documentation is publically available.
Documentation must indicate that automatic duplex printing is enabled at the time of product shipment and using the default standard size media type and size settings. If N/A is declared, documentation must be provided to support the reasoning.
Information must show where product documentation is publically available.
Publically available information must show the product ships with duplex printing as the default.
A stand alone scanner with no possible duplexing functionality is an example of a product which might declare N/A.
Somewhat difficult to
demonstrate conformance
Sample Conformity Packet
1680.24.5.4.1: Optional– Default to automatic duplex printing
1680.2 4.5.4.1
The following data samples and explanation are intended to illustrate examples of acceptable data. Other types or forms of data may also be acceptable in conformity documentation.
Publically available product documentation indicating automatic duplex printing enabled
1680.2 4.5.4.1
This excerpt from a product manual indicates
that 2-sided printing (duplex printing) is the
default setting when the product is shipped. It is
also available online clicking on the hyperlink.
Printer XYZPrinter 123Printer ABC