configure the ip address connect to encoder’s serial port power on encoder connect serial cable to...
TRANSCRIPT
![Page 1: Configure the IP Address Connect to encoder’s serial port Power on encoder Connect serial cable to “Data A” Hold in “Console” until “Data A” light turns](https://reader037.vdocuments.us/reader037/viewer/2022102722/551c01f0550346b24f8b4c9d/html5/thumbnails/1.jpg)
Configuring an Impath i4110
![Page 2: Configure the IP Address Connect to encoder’s serial port Power on encoder Connect serial cable to “Data A” Hold in “Console” until “Data A” light turns](https://reader037.vdocuments.us/reader037/viewer/2022102722/551c01f0550346b24f8b4c9d/html5/thumbnails/2.jpg)
Configure the IP AddressConnect to encoder’s serial port
Power on encoderConnect serial cable to “Data A”
Hold in “Console” until “Data A” light turns solid red
![Page 3: Configure the IP Address Connect to encoder’s serial port Power on encoder Connect serial cable to “Data A” Hold in “Console” until “Data A” light turns](https://reader037.vdocuments.us/reader037/viewer/2022102722/551c01f0550346b24f8b4c9d/html5/thumbnails/3.jpg)
Open Putty with the proper settings (COM port may vary)
Click Open
Type in the user name and password impath impath
![Page 4: Configure the IP Address Connect to encoder’s serial port Power on encoder Connect serial cable to “Data A” Hold in “Console” until “Data A” light turns](https://reader037.vdocuments.us/reader037/viewer/2022102722/551c01f0550346b24f8b4c9d/html5/thumbnails/4.jpg)
1. Type “maint” and hit enter 2. Select “3” and hit enter
3. Select “3” and hit enter 4. Configure options 1, 2, 3 like below
![Page 5: Configure the IP Address Connect to encoder’s serial port Power on encoder Connect serial cable to “Data A” Hold in “Console” until “Data A” light turns](https://reader037.vdocuments.us/reader037/viewer/2022102722/551c01f0550346b24f8b4c9d/html5/thumbnails/5.jpg)
5. “Q” out of the menus saving if asked6. Type “reboot” and hit enter
At this point you can disconnect your serial cable
![Page 6: Configure the IP Address Connect to encoder’s serial port Power on encoder Connect serial cable to “Data A” Hold in “Console” until “Data A” light turns](https://reader037.vdocuments.us/reader037/viewer/2022102722/551c01f0550346b24f8b4c9d/html5/thumbnails/6.jpg)
Configuring the Terminal Server
Connect the encoder to the network or directly to you laptop with a cat5 cable
Connect to the encoder with putty, this time using the “Telnet” connection type
Enter the username and password
![Page 7: Configure the IP Address Connect to encoder’s serial port Power on encoder Connect serial cable to “Data A” Hold in “Console” until “Data A” light turns](https://reader037.vdocuments.us/reader037/viewer/2022102722/551c01f0550346b24f8b4c9d/html5/thumbnails/7.jpg)
Enter the “maintenance” menu
Select “4” to open service manager menu
Select “2” to configure serial port options
![Page 8: Configure the IP Address Connect to encoder’s serial port Power on encoder Connect serial cable to “Data A” Hold in “Console” until “Data A” light turns](https://reader037.vdocuments.us/reader037/viewer/2022102722/551c01f0550346b24f8b4c9d/html5/thumbnails/8.jpg)
#1 “Data Port Interface Settings” comes pre-configured to work with our Vicon cameras and in most cases will not need to be configured.
#2 “Data Circuit Network Settings” is where we will configure the Terminal Server Mode and port number.
![Page 9: Configure the IP Address Connect to encoder’s serial port Power on encoder Connect serial cable to “Data A” Hold in “Console” until “Data A” light turns](https://reader037.vdocuments.us/reader037/viewer/2022102722/551c01f0550346b24f8b4c9d/html5/thumbnails/9.jpg)
Select “2” and then select the port you wish to configure1 is for port A2 is for port B
By default both ports are disabled.We typically use port B for the camera so that we don’t have unplug the camera if we want to access the encoder with a serial cable which can only be done on port A
Select “2” to configure port B (unless the port is damaged and you are switching to port A)
![Page 10: Configure the IP Address Connect to encoder’s serial port Power on encoder Connect serial cable to “Data A” Hold in “Console” until “Data A” light turns](https://reader037.vdocuments.us/reader037/viewer/2022102722/551c01f0550346b24f8b4c9d/html5/thumbnails/10.jpg)
Select “1” to change the Network Service Mode
Select “2” to configure the terminal server to “Unicast TCP Server” mode
![Page 11: Configure the IP Address Connect to encoder’s serial port Power on encoder Connect serial cable to “Data A” Hold in “Console” until “Data A” light turns](https://reader037.vdocuments.us/reader037/viewer/2022102722/551c01f0550346b24f8b4c9d/html5/thumbnails/11.jpg)
Select “2” to change the TCP port to “4002”
“Q” out of the menus typing “y” to save when asked until you get back to the first menu
![Page 12: Configure the IP Address Connect to encoder’s serial port Power on encoder Connect serial cable to “Data A” Hold in “Console” until “Data A” light turns](https://reader037.vdocuments.us/reader037/viewer/2022102722/551c01f0550346b24f8b4c9d/html5/thumbnails/12.jpg)
Configuring the Video Encoder
![Page 13: Configure the IP Address Connect to encoder’s serial port Power on encoder Connect serial cable to “Data A” Hold in “Console” until “Data A” light turns](https://reader037.vdocuments.us/reader037/viewer/2022102722/551c01f0550346b24f8b4c9d/html5/thumbnails/13.jpg)
1. Select “4” 2. Select “1”
3. Select “3” 4. Select “1”
![Page 14: Configure the IP Address Connect to encoder’s serial port Power on encoder Connect serial cable to “Data A” Hold in “Console” until “Data A” light turns](https://reader037.vdocuments.us/reader037/viewer/2022102722/551c01f0550346b24f8b4c9d/html5/thumbnails/14.jpg)
Option 1 “Video Encoder” should be left at the factory defaults
![Page 15: Configure the IP Address Connect to encoder’s serial port Power on encoder Connect serial cable to “Data A” Hold in “Console” until “Data A” light turns](https://reader037.vdocuments.us/reader037/viewer/2022102722/551c01f0550346b24f8b4c9d/html5/thumbnails/15.jpg)
Option 2 “Video Network” is where we set the multicast address/port and stream type
Configure options 1, 2, 4, and 8 as seen here
“Q” out of the menus typing “Y” to save when asked until you reach the “maint” menu
The encoder is now ready to be deployed in the field