config skypilot
TRANSCRIPT
-
7/30/2019 Config Skypilot
1/2
Setting Up Your First SkyPilot Network
Using this guide
This document provides a quick
start guide to setting up a baselineSkyPilot wireless mesh network.
You can set up a ully-unctional,
demonstration network using any
o the three topologies shown in
the fgures.
Tags in the fgures identiy the
panels that provide instructions or
installing and manually confguring
SkyPilot devices. (Each topology
requires a SkyGateway.)
Note: To ensure mesh network
connectivity, make sure you speciy
the same requency and domain or
all SkyPilot devices on the network.
What you need
Product kits or the net-
work you will be setting
up, including mounting
hardware and extra
cabling.
Two notebook computers
to use as consoles or con-
fguration and verifcation.
(One notebook must have
Wi-Fi capability i youre
setting up a SkyPilot Ex-
tender DualBand.)
SkyGateway SkyExtender
Notebook
CA
Ethernet
IPaddress192.168.0.20
Wirelessmeshnetworkconnection
Ethernet
Frequency5740
IPaddress192.168.0.10
Frequency5740
IPaddress192.168.0.2
Follow the instructions in panelA to set up and congure a SkyGateway. Next, ollow the instructions in panel C andA to set up and congure aSkyExtender to operate as a node on the SkyPilot network. Veriy that the mesh network connection is active by pingingthe notebook attachedto the SkyGateway.
SkyGateway with SkyExtender node
Verifywirelessmesh
connectivityby usingthenotebookconnectedto theSkyExtendertop ingthe
notebookconnectedto theSkyGateway.
A
Gotopanels:Gotopanel:
SkyGateway SkyConnector
Notebook
CA
Ethernet
IPaddress192.168.0.20
Wirelessmesh
networkconnection
Ethernet
Frequency5740
IPaddress192.168.0.10
Frequency5740
IPaddress192.168.0.2
Follow the instructions in Panel A to set up and congure a SkyGateway. Next, ollow the instructions in Panel C to set up and congure aSkyConnector to operate as a node on the SkyPilot network. Veriy that the mesh network connection is active by pingingthe notebookattached to the SkyGateway.
SkyGateway with SkyConnector node
Gotopanel:Gotopanel:
SkyGateway SkyExtender DualBand
Notebook
A
Ethernet
IPaddress192.168.0.20
Wirelessmeshnetworkconnection
Wi-Finetworkconnection
Frequency5740
IPaddress192.168.0.10
Frequency5740
IPaddress192.168.0.2
Follow the instructions in Panel A to set up and congure a SkyGateway. Next, ollow the instructions in Panel B to set up and congure aSkyExtender DualBand to operate as a node on the SkyPilot network. Veriy that the mesh network connection is active by pingingthe notebookattached to the SkyGateway.
SkyGateway with SkyExtender DualBand node
B
Verifywirelessmeshconnectivitybyusingthe
notebookconnectedto theSkyExtendertoping the
notebookconnectedto theSkyGateway
Gotopanel:Gotopanel:
> set prov manual
Changed provisioning state to manual.
-> Enter primary Frequency [5745]: 5760
> set prov domain
-> Enter domain ID (1-10000) [1234]: 1240
Domain ID changed: 1240
> reboot
Rebooting ...
+ S J M SU
*
\
, 7
, * ",
*
" /
/-
1
"
, /1 *
" , 1
"9 ,7"*
,/1*"
*
\
, 7
, * ",
*
" /
/-
1
"
, /1 *
" , 1
"9 ,7"*
,/1*"
The SkyGateway operates as a hub
or your wireless mesh network. As
the interace to wired inrastructure,
a SkyGateway provides subscriberswith access to the internet or WAN.
Cable cover
Serial cable
Weathergasket
Ethernetcable
SkyGatewayA
Connect Ethernet and serial cables, threading the cables through theprovided cable cover and gaskets. Reattach the cover, making surethe Ethernet cable passes through the cutout.
4 Power and Ethernet
Ethernetcable
Powercord
Connect the Ethernet cable extending rom the SkyGateway to theport labeled CPEon the power injector. Connect an Ethernet cablebetween the port labeled Computeron the power injector and anEthernet port on the notebook computer. Plug the AC adapter intothe power injector and connect the power cord to the AC adapter.Plug the power cord into an out let to power on the SkyGateway.
Connect the serial straight-through cable exteSkyGateway to the provided DB-9 adapter, tha serial port on the notebook computer.
DB-9 ada
Serial straight-through cable
Notebook
Serial port
From the notebook, start a terminal emulation program (orexample, Tera Term) and select the COM port on which theserial cable is attached. Connect to the device using these serialcommunication settings: 38400 bps, 8 data bits, no parity, one stopbit, and no fow control.
Entersetprov manualto enable manual provisioning. At the prompt,enter a primary requency. Useset prov domain to supply a domain.Enter rebootto apply the conguration to Flash memory and restar t.
Observe the boot messages in the terminal wor GPSails to resolve, conrm that a GPS sigGPS acquisition can take up to 15 minutes, evreception. When the welcome message appeby entering the deault password,public.
Whats next?To set up a SkyPilot SkyE
DualBand to provide acc
mesh network via Wi-Fi e
devices, go to panel
To set up a SkyConnecto
Extender to provide acce
mesh network via a PC o
panel
SkyGateways and SkyExtenders use a
GPS signal to synchronize with other
devices on the network. To ensure optimal
reception, mount the unit outdoors with
an unobstructed view o the sky and use
a handheld GPS receiver to check signal
strength.
1 Attach cables
Serial port
3 Make terminal connection 5 Log into SkyGatew
2 Connect notebook
6 Confg ure and reboot
B
C
Ethernet port
On the notebook computer, open the Network control panel andcongure a new network connection. Give the notebook an IPaddress o 192.168.0.20 and a Netmask o 255.255.255.0.
7 Create network connection
192 168 0 20
Powerinjector
Ethernetcable AC adapter
Verifywirelessmeshconnectivityby usingthe
notebookconnectedto theSkyConnectortoping the
notebookconnectedto theSkyGateway
-
7/30/2019 Config Skypilot
2/2
Q:\> ping 192.168.0.20
Pinging 192.168.0.20 with 56 data bytes:64 bytes from sbc405gpr (192.168.0.20): icmp_seq=0. time=0. ms64 bytes from sbc405gpr (192.168.0.20): icmp_seq=1. time=0. ms64 bytes from sbc405gpr (192.168.0.20): icmp_seq=2. time=0. ms----192.168.0.20 PING Statistics----3 packets transmitted, 3 packets received, 0% packet lossround-trip (ms) min/avg/max = 0/0/0
Q:\>
>show link
Node Id LType NType State RSSI LTxMod RTxMod LA----------------- ----- ----- --------- ---- ------ -----
00:0a:db:00:00:30 data ext act mgmt 55 54 54 0
Choose a wireless network
080007A92BFC
Security-enabledwireless network
Click an item in the listbelow to connectto a wireless network in range or to getmore
information
SkyExtender DualBandB
From the notebook, open a DOS command window and ping the IPaddress o the notebook computer connected to the SkyGateway,192.168.0.20. Iping ails to return packets, repeat steps 3-7.
2.4 GHz antenna
Attach the two 2.4 GHz antennas included with the device to t hestandard N connectors on the base o t he SkyExtender DualBand.
2 Attach antennas
Ater reboot, log in to the device and entershow linkto view thecurrent network status o the device. I an active path is present, theSkyExtender DualBand is communicating with the network. Note:link ormation may take several minutes.
1 Attach cables
Connect Ethernet and serial cables, threading the cables through theprovided cable cover and gaskets. Reattach the cover, making sure theEthernet cable passes through the cutout.
Cable cover
Serial cable
Weathergasket
Ethernetcable
In addition to extending network
range, a SkyExtender DualBand
can operate as a node providing
a wireless access point or Wi-Fi
enabled devices.
Open the Network control panel and set up a wireless connectionwith the IP address 192.168.0.10 and Netmask 255.255.255.0. Fromthe Network Connection control panel choose the SSID associatedwith the device access point. (The network key ispublicpublic.)
8 Veriy network connection6 Reboot and veriy link
SkyGateways and SkyExtenders use a
GPS signal to synchronize with other
devices on the network. To ensure optimal
reception, mount the unit outdoors with
an unobstructed view o the sky and use
a handheld GPS receiver to check signal
strength.
Serial port
Ethernet port
From the notebook, start a terminal emulation program (orexample, Tera Term) and select the COM port on which theserial cable is attached. Connect to the device using these serialcommunication settings: 38400 bps, 8 data bits, no parity, one stopbit, and no fow control.
3 Make terminal connection
Welcome to SkyPilot Network s, Inc.
Copyright (C) 2006 SkyPilot Networks, Inc. All Rights Reserved.
Password: ******
Login successful
> set prov manualChanged provisioning state to manual.
> set prov freq
19 available frequencies are the following:
5735 5740 5745 5750 5755 5760 5765 5770 5775
5780 5785 5790 5795 5800 5805 5810 5815 5820
-> Select a Frequency action: quit, primary, allow, deny, list,
region, dwell time : p
-> Enter primary frequency [5745]: 5760
-> Select a Frequency action: quit, primary, allow, deny, list,
region, dwell time : q
> set prov domain
-> Enter domain ID (1-10000 or all) [all]: 1240
Domain ID changed: 1240
> reboot
Rebooting...
In the terminal window, watch the boot messages to conrm acquisi-tion o a GPS signal. When a welcome message appears, log in to thedevice by entering the deault password,public. Entersetprov manualto enable manual provisioning mode . Entersetprov freq and supply aprimary requency. Enter setprov domain andprovide a domain. Enterrebootto save the conguration to fash memory and restart.
5 Lo g in and confgure
7 Set up Wi-Fi connection
*
\
, 7
, * ",
*
" /
/-
1
"
, /1 *
" , 1
"9 ,7"*
,/1*"
*
\
, 7
, * ",
*
" /
/-
1
"
, /1 *
" , 1
"9 ,7"*
,/1*"
Connect the serial straight-through cable extending rom theSkyExtender DualBand to the provided DB-9 adapter, then plug theadapter into a serial port on the notebook computer. Connect theEthernet cable to the port labeled CPEon the power injector. Plugthe AC adapter into the power injector and connect the power cordto the AC adapter. Plug the power cord into an outlet.
DB-9
adapter
Serialstraight-
throughcable
Notebook
4 Noteb ook and power
Power
injector
ACadapter
SSIDis theMAC address ofthe SkyPilotDual-Band(provided onlabel attachedto base)
>show link
NodeId LTypeNTypeState RSSILTxModRTxModLAntRAnt---------------------- -------------- ---------- -----0 0: 0a :db: 00 :0 0: 30 dat a e x t a ctmgmt 5 5 5 4 5 4 0 3
Q:\> ping 192.168.0.20
Pinging 192.168.0.20 with 56 data bytes:64 bytes from sbc405gpr (192.168.0.20): icmp_seq=0. time=0. m64 bytes from sbc405gpr (192.168.0.20): icmp_seq=1. time=0. m64 bytes from sbc405gpr (192.168.0.20): icmp_seq=2. time=0. m----192.168.0.20 PING Statistics----3 packets transmitted, 3 packets received, 0% packet lossround-trip (ms) min/avg/max = 0/0/0
Q:\>
E
P C
: GNI NR
AW
RE P O
R P MI
NOI TA L
LA TS NI
E GA MA D
DLUOC
R E TUP M
OC R UO
Y
REWOP
RETUP
MOC
>set prov manual
Changed provisioning state to manu
>set prov freq
19 available frequencies are the foll5745 5750 5755 5760 5765 5770 575790 5795 5800 5805 5810 5815 585835
-> Select a Frequency action: quit, pallow, deny, list, reqion, dwell time: p
->Enter primary frequency [5745]:
-> Select a Frequency action: quit, pallow, deny, list, reqion, dwell time: q
>reboot
E P C
: GNI N
R AW
RE P O
R P MI
NOI TA L
LA TS NI
E GA
MA DDLU
OC
R E TU
P MOC R
UOY
REWOP
RETUPM
OC
SkyConnector or SkyExtenderC
2055 Laurelwood Road
Santa Clara, CA 95054-2747
(408) 764-8000 or
(866) SKYPILOT
www.skypilot.com
2 Power
Insert an Ethernet cable through the weather gasket and connect tothe Ethernet port on the back o the SkyConnector. Attach the deviceto a pole.
3 Connect notebook
Connect a second Ethernet cable rom the power injector portlabeled Computerto a notebook computer.
Ater rebooting the device, enter the show link command to view thecurrent network status o t he device. Enter q to quit the command-line interace.
From the notebook, open a DOS command window andping theIP address o the notebook computer connected to the SkyGateway,192.168.0.20. Iping ails to return packets, repeat steps 4-7.
A SkyConnector or SkyExtender can
operate as a node on the wireless
mesh network, providing Internet
access via a PC or router connected
to the device.
Note: I using a SkyExtender instead
o a SkyConnector, perorm steps
1 through 5 in panel then
return to this panel and pick up the
installation at step 4.
Telnet to the device at IP address 192.168.0.2passwordpublic. Enterset prov manualand chyou gave the SkyGateway. Enter q to exit the crebootto apply the conguration to Flash mem
5 Log in and confgu
On the notebook computer, open the Network control panel andcongure a new network connection. Give the notebook an IP ad-dress o 192.168.0.10 and a Netmask o 255.255.255.0.
4 Create network connection
7 Veriy network connection6 Veriy link
192 168 0 10
Connect the Ethernet cable to the port labeleinjector. Plug the AC adapter into the power iadapter into an outlet.
Ethernetcable
Whats next?For more detailed docu
on setting up SkyPIlot d
managing a wireless me
visit www.skypilot.com/s
1 Mount the device
Weather gasket
Ethernet cable
A