confidential1 panasonic communications co., ltd. network business company edition 1.3 07 jul., 2004...
TRANSCRIPT
Confidential 1
•Panasonic Communications Co., Ltd.•Network Business Company•Edition 1.3 07 Jul., 2004
Enhanced Items
KX-TDA200/100 System (Ver.1.1)
Confidential 2
General
-System Highlight
- New Features
- Condition of New Features
- Software Compatibility
Confidential 3
V1.0
V1.1
Networking(QSIG), Call Center, VoIP Gateway,
CTI (CSTA/TAPI), T76xx Line Up, Wireless System
- Digital XDP & Double Extension Capacity by MEC - New VoIP Gateway Card (Panasonic proprietary)- New CS to DPT Port- And other new features
System Highlight
Confidential 4
BRI4, IPGW4E, CSIF4, 2chCS, MECDXDP & Double Extension CapacityNew IPGW Card2chCSBroadcastingDialing PlanExt. CLIP sending on Emergency CallShort Cut Access to System Speed DialModified DDI Number is displayed on LCDImproved DSS LED Flash / Call Pick upDisable Hold RecallDisable re-count Ext-CO Duration Limitation by Hold RetrieveISDN-3party ConferenceDTMF Tone through a Conference from PTIntercept Timer for each time mode(Day/Night/Lunch/Break)SMDR RC/AN information outputPaging to other paging groupCOS Name is programmableCS port Name is programmableExt. CLIP Automatic GeneratingDDI/DID Name Automatic GeneratingWireless XDP Programming from PCLogical CheckPS Hand-Over during Conference CallWalking Extension from Fault Extension
HardwareFunction
Improvement
Highlight
Making calls
Receiving calls
Hold/FWD/TR
Conference
TimerOthers
Programming
New Features
Confidential 5
New FeaturesDXDPDouble Extension Capacity2chCSBroadcasting
Another Features
Software ConditionDHLC/DLC = 2.005DHLC/DLC = 2.005DHLC/DLC = 2.005
No
No
Hardware ConditionNo
MEC(TDA0105)No
MEC(TDA0105)
No
Condition of New Features
Confidential 6
Software CompatibilityMPR / LPR
MPR 1.1xxMPR 1.0xx
YES
YES w/o DXDP, TDA0141
YES
YES
DLC/DHLC 2.005DLC/DHLC 1.xxx
MPR / PC maintenance console
MPR 1.1xxMPR 1.0xx
YES
NO
YES
YES
1.071.06
Confidential 7
Hardware
- New Hardware
- Power Factor Summary
Confidential 8
CSIF4(4 Cell Station Interface)
KX-TDA0143
4-port CS interface card for 4 CSs(TDA0142).
MEC(Memory Expansion Card)
KX-TDA0105
2ch CS(CS to DPT Port)
KX-TDA0141
* Memory expansion for - Broadcasting feature - Double the number of DPTs (DXDP)* To be installed in the MEC slot on MPR card
Connect to DPT port (CSIF card is not needed)2.4GHz (KX-TDA0141), DECT(KX-TDA0141CE)
IPGW4E(4ch VoIP Gateway)
KX-TDA0484
TDA200 4TDA100 2
TDA200 4TDA100 2
TDA200 1TDA100 1
TDA200 32TDA100 16
4-channel VoIP gatewayVoIP H.323 V.2, ITU-T G.729a, G.723.1, G.711T38 (FAX) is not supportedPanasonic proprietary IPGW card
New Hardware
Confidential 9
* Calculated with base card, not using base ports.
IPGW4
PRI-30
BRI-8
BRI-4
CID (CO)
E1
E&MLCOT-16
LCOT-8LPR Card
TDA0480
TDA0290
TDA0288
TDA0284
TDA0193
TDA0188
TDA0184TDA0181
TDA0180Model
0
0
0
0
0
0
00
0Power units
IPGW4E TDA0484 0
MSG
RMT
TDA0191
TDA0196
0
0
CTI-LINK TDA0410 0
Echo
DPH-2/4
TDA0166
TDA0161/162
0
0
MEC TDA0105 0
Trunk Card Extension Card
Other Terminals
Voice Mail (D-PT)
T72xx/T74xx/T75xx
BRI Extension
T76xx, T7560, T7565 1/Extension
2/Port (2ch)
4/Extension
2/Port (2ch)
CS (TDA0142) 4/CS
CS (TDA0141) 4/CS
APT & DSS console 4/Extension
SLT 0
MSLC-16
SLC-16
DHLC-8
DLC-16
DLC-8
SLC-8
LPR Card Model Power units
CS I/F-8
TDA0175
TDA0174
TDA0170
TDA0172
TDA0171
TDA0173
TDA0144
16/Card*
16/Card*
8/Card*
0
0
8/Card*
0
CS I/F-4 TDA0143 0
Power factor summary (Ver. 1.1)
Confidential 10
Function - Highlight
- DXDP & Double Extension Capacity
- New IPGW Card
- 2ch CS
Confidential 11
- DPT on DPT without additional HW or SW
- Easy installation for additional Extensions
- 1 DHLC port => 3 telephones (2x DPT+1x SLT)
* DHLC Card = Max 24 Ext.
- 1 DLC port => 2 telephones (2x DPT)
* DLC16 Card = Max 32 Ext.
* DLC8 Card = Max 16 Ext.
DXDP-Slave
XDPor
4 Wires 4 Wires 2 Wires
XDP
4 Wires 2 Wires
2 Wires
DHLC Port
DHLC Port
SLTSLT
SLTSLT
DXDP-Master
2 Wires
DXDP-Slave
2 WiresDLC Port
2 Wires 2 Wires
2 Wires
DHLC PortSLTSLT
Digital XDP (DXDP) -1
Confidential 12
Capacity for ExtensionV1.0 V1.1
DXDP
MEC
TDA100
TDA200
No
No
Yes
No
Yes
Yes
Max 64 Ext.
Max 128 Ext.
Max 64 Ext.
Max 128 Ext.
Max 128 Ext.
Max 256 Ext.
Additional DPT can be installed without buying another DHLC or DLC, but total capacity does not change without MEC.
System Capacity (Trunk & Extension mixed)
V1.0
TDA100 80 (108) portsTDA200 160 (216) ports
V1.1 with DXDP&MEC
TDA100 144 (158) portsTDA200 288 (316) ports
Digital XDP (DXDP) -2
Confidential 13
MEC(TDA0105) How to check the TDA0105 If the TDA0105 is not installed.
If the TDA0105 is installed.
Click”
If connected extension is exceed 128 with M type PSU, what happens?
- 129th Extension (PT) will not come in service. - Minor error log = PT Connection Over.
DHLC-8 8 (Fixed) + Connected PT/DSS/VMSLC-8 8 (Fixed)DLC-8 Connected PT/DSS/VMSLC-16 16 (Fixed)DLC-16 Connected PT/DSS/VM
PU for extension cards
Digital XDP (DXDP) -3
Confidential 14
Condition-3
- OHCA function can not be used
- T7601 (USB) can not be used
(PC Phone / PC Console / PC Programming)
Master Slave
- T7625- T7630- T7633- T7636- T7665
- T7625- T7630- T7633- T7636- T7665
Telephone
Can be used
- A-PT- T72xx- T74xx- T75xx- DSS
- A-PT- T72xx- T74xx- T75xx- DSS- CS
Can not be used
Condition-2DXDP-Slave
ø0.4mm Max.40mø0.5mm Max.50mø0.6mm Max.60m
DXDP-Master
Condition-1 ø0.4mm Max. 500mø0.5mm Max. 720mø0.6mm Max. 830m
Condition-4
ParallelConnection !
No!No!
Digital XDP (DXDP) -4
Confidential 15
- 4ch IPGW Card
- G729a/G723.1/G711
- T.38 (FAX) mode is not supported (FAX = G711)
- Physical I/F: 10/100 Base-T
- Web programming (English)
- Interoperability with TDA0480:
Incoming call, Outgoing call and CLIP only.
- Interoperability with another manufacturers :
Not guaranteed.
1st Time Setup Connection
TDA100/200
TDA0484
10/100 Base-T Cross Cable
(http://192.168.1.200)
Pattern 1
TDA100/200
TDA0484
10/100 Base-T Straight Cable
Switching HUB
(http://192.168.1.200)
Pattern 2
IE5 or later
IE5 or later
General
VoIP Gateway Card (KX-TDA0484) - 1
Confidential 16
VoIP Gateway Card (KX-TDA0484) - 2
No
Proprietary
511
G.723/G.729a
T.38
16ms
Yes
Yes
Yes
Yes
No
H.323 V2
Yes (Client)
H.323 V4 Annex M1
511
G.711/G.723.1/G.729a
G.711
16ms
No
Yes
No
No
No
H.323 V2
TDA0480TDA0484/TDA3480Compatibility
DHCP
QSIG service
Max networked IPGW cards
Voice Codec
FAX Protocol
Echo canceller G.165/G.168
AGC
DTMF Tone Detection
SNMP
Event Notice by email
NAT
Signalling
New IPGW Card (Compatibility)
Confidential 17
VoIP Gateway Card (KX-TDA0484) - 3New IPGW Card (Interoperability)
TDA0480connect toTDA0480
OKOKOKOKOKOKOKOKOKOK
OK
OKOK
TDA0484/TDA3480connect to TDA0480
NoNoNoNoNoNoNoNoNoNo
OK
OKNo
TDA0484/TDA3480connect to
TDA0484/TDA3480
OKOKOKOKOKOKOKOKOKOK
OK
OKOK
Function
CLIRCOLPCOLRCNIPCNIRCONPCONRCT(Avoid tromboned)CF(Avoid tromboned)CCBS
CLIP
Making/Receiving callFAX Connection
Confidential 18
How to connect TDA0480 & TDA0484…
Outline of example
TRG2 TRG2
IP_Address: 192.168.1.200 IP_Address: 192.168.1.12
Subnet Mask:255.255.255.0Default GW: 192.168.1.1
IP_Address: 192.168.1.100
TDA0484 TDA0480
Ext.102TIE Access = 7
Ext.103TIE Access = 7
PBX Code= 81
PBX Code= 82
Switching HUB
Dial = [7]+[82]+[103] 103 of PBX82
Dial = [7]+[81]+[102] 102 of PBX81
TIE Routing TableLead : 82Remove : 0Added : noneTrunk : 02
TIE Routing TableLead : 81Remove : 0Added : noneTrunk : 02
A-low A-low
VoIP Gateway Card (KX-TDA0484) - 4
Confidential 19
TDA0484 Setting* Address Setting (IP Address of Card)
1.Programming1.1 Network Settings, General1.1.1 IP Address Setting
IP Address : 192.168.1.200Subnet Mask: 255.255.255.0Default GW : 192.168.1.1
* Handling setting for Incoming Call from IP Network1.Programming1.5 Hunt Pattern (for Incoming Group)
Hunt Group Grp1 = Port 1 & Port 2 Grp2 = noneHunt Pattern 1: Rcv Leading Digit = 81, Hunt Group = 1
Port 1 Port 2
BRI-QSIG
Incoming81102
PBX Code= 81
TDA0484
TRG
2
BRI-QSIG
TRG
2
IP Network
IP Network
Outgoing82103
* Handling setting for Outgoing Call from PBX to IP Network1.Programming1.6 DN2IP (Dialed Number to IP Address Translation)1.6.1 GW Entry1.6.2 DN2IP Entry
GW No.= 1Comment = 82 Office, TDA0480IP Address = 192.168.1.12Group No. = 0
Leading No. = 82Remaining Number of Digits = 3GW No./Group No. Selection = GWGW No./Group No. = 1
1.Programming1.4 VoIP Gateway/IP-PBX Interface Settings1.4.2 Others
G711 A-Law
* Interface between IPGW & PBX
VoIP Gateway Card (KX-TDA0484) - 5
Confidential 20
General TabIP Address : 192.168.1.12Subnet Mask : 255.255.255.0Rout Address 1: 192.168.1.1Rout Address 2: none
Trunk Data TabPort1 Trunk Group #1 Interface type = Basic Interface Length of call reference = 1Port2 --- same as Port1Configuration = QSIG
Hunt pattern Tab --- Incoming call Handling
Destination Number = 82Hunt pattern = 1
Trunk priority Tab
Hunt pattern 1: Priority1 = Trunk group#1 (Default)
Other TabA-law/m-law flag = A-law
DNS EditingTerminal = 81Remaining digits = 3Selected unit = TDA0484 Unit ICON
TDA0480 Setting
Configuration procedure 1. Configure TDA0480 own setting
2. Create “Other Unit” --- TDA0484 IP Address
3. Edit DNS table and send to TDA0480
4. Reset PBX after sending all data for TDA0480
VoIP Gateway Card (KX-TDA0484) - 6
Confidential 21
GW Grouping (Slide Call feature)In the case that TDA has more than an IP-GW, you can group these IP-GWs.
IP Network
Grouping
Benefit of the GW Grouping : Slide Call In the case that the IP-GW(a) is not
available because all channels are in use for example, originating IP-GW try the IP-GW(b).
IP Network
Not available
Originating IP-GW
IP-GW(b).
IP-GW(a).
VoIP Gateway Card (KX-TDA0484) - 7
Confidential 22
TDA0141&TDA0142 total
Max.32 CS / TDA200
Max.16 CS / TDA100
4 PU / CS
- Two Voice Paths per CS.- A specific CS I/F card is not needed.- A port on DHLC and DLC cards can used as the interface for KX-TDA0141.- Max. number of CS: TDA100=16 TDA200=32 (Including TDA0142).- DHLC/DLC cards software must be 2.005 or later.- Functionality : The same as TDA0142- Hand-over TDA0141 TDA0142: “YES” - Power factor is 4.
- CS Port assignment is not needed.
The TDA automatically detects the connected CS (as same as DPT connection).
DHLC
DLC
TDA0141TDA0144
TDA0143
TDA0142
ø0.4mm 222mø0.5mm 347m (CAT5)ø0.6mm 500m
2ch Cell Station (KX-TDA0141) -1
Confidential 23
How to update the CS software
1- Set a CS port to “OUS” 2- Go to “SD Card File View and Load”3- Select “PDCSDECT” (or “PDCS24G”)4- Click “Detail”
5- Take the same procedure of Ver.1.0
2ch Cell Station (KX-TDA0141) -2
Confidential 24
Function – Making Calls
- Broadcasting
- Dialing Plan
- Ext. CLIP sending on Emergency Call
- Short Cut Access to System Speed Dial
Confidential 25
211
212
213
214
215
FWD to somewhere
The caller receives C.Tone for each
time.
No RingNo Ring
An PT user (Owner) can make one way path call (= announce) to 31 parties simultaneously.After one of called party answering, the owner can begin announcement.This feature requires MEC(Memory Expansion Card : KX-TDA0105).
Configuration
211212213214215
- Wired Extension- PS-Other PBX’s Extension (Only Closed Numbering)*- Outside Telephone Number **: Only available when the networking type of the trunk is assigned as private.
* Up to 32 digits
[1][*32]+
Announce
C.Tone
C.Tone
C.Tone
One Way Path
Max.31 members
8 Groups / System
If no member answer, I cancel broadcasting and send busy tonebusy tone to the
caller.
2.System - 4.Timers & Counters - 2.DISA/DPH/CONF/T.Reminder"Answer Waiting Timer for Broadcasting Group (s)" = 0 - 120
Because of DND / PS in XDP ParallelRestriction from TRS/Barring / Call Charge Limit
Operation
Off-Hook
Off-Hook
Off-HookOverride
FWD setting
In case of No Answer, it will be disconnected by
timer.
COS:“Broadcasting Operation”
= Enable Owner
PT onlyPT only
Broadcasting - 1
Confidential 26
Announce 211Member-01
212Member-02
213Member-03
214Member-04
215Member-05
Joining Order1st --- 2nd ---3rd ---
201The owner
Conversation during broadcasting1.To let members join to conversation
2.To let members leave from conversation
(1) The Owner pushed [DSS - 212] => Ext.212 join to conference
(2) The Owner pushed [Conf.] => Youngest Member (=Ext.211) join to conference
(3) Listening Member pushed [DSS - 201] or Recall/Hookswitch=> Notification Tone goes to the owner, Member’s information appear on the Owner’s LCD.
=> The Owner push [DSS - 214] => Ext.214 join to conference
NotificationTone
LCD:Ext.214 wants conversation !
Ext.212 --- By (1)Ext.211 --- By (2)Ext.214 --- By (3)
(1)
(2)
(3)
Push [DSS-211]Push [Transfer]Push [Flash/Recall]
In above situation, when the owner does following action…
Ext.211 goes back to be a listenerLast joined member (=Ext.214) goes back to be a listenerLast joined member (=Ext.214) is disconnected from broadcasting.
Conversation with the Owner
= Max.3 MembersMax.3 Members( 4 ( 4 Party Conference )Party Conference )
Broadcasting - 2
Confidential 27
Broadcasting - 3
From an owner Extension, Dial *32 + Broadcasting group number
When a member of the group answers the call.
Conference : 2 ConferenceNo of member
LCD Display in typical conditionIn establishing
Owner Extension Called Extension
Conference1: PCCUKConference1: PCCUK
Owner Extension Called Extension
In broadcasting
Name of Broadcasting Group
Confidential 28
Broadcasting - 4Additional information
Internal Call Block is Block
Set to Call FWD
Set to DND
Busy
Auto Answer
Wireless XDP PS
Condition of Member Ext. Response for Arriving Broadcasting Call
The broadcast call arrives this extension.
The broadcast call does not arrive this extension.
Call Waiting function will be performed.
The Auto Answer function will not be performed.
The broadcast call does not arrive this PS.
The broadcast call does not arrive this extension.
Conditions and Responses of Member Extension
If owner extension has DSS key of a member of broadcasting group and establishes a broadcasting call, the DSS key does not flash when the called extension rings.It actually turns red (not flashing).
DSS key of Owner Extension which relates with member extension
Confidential 29
Dialing Plan Table for each TRG
(Table1 – Table4)
Max.32 digits
4 Tables independently
1: N112: NXXXXXX3: 1NXXNXXXXXX
1: N112: NNXXXXX3: 1NPXNXXXXXX
1: N112: NXXXXXX3: 1NNXXXXX4: 1NPXNXXXXXX
1: N112: NXXNXXXXXX3: 1NXXNXXXXXX
48: N1149: NXXXXXX50: 1NXXNXXXXXX
Type-A
Type-B
Type-C
Type-D
Type-E
N = 2-9P = 0,1X = 0-9,*,#
Max.50 leading numbers
Voice Path Tx: Mute Rx: OK
( during Dialing ) PBX recognizes the end of dialing!
Voice Path Tx: OK Rx: OK
Voice Path Tx: OK Rx: OK
( Start of Dialing )
( End of Dialing )
Dialing Planis working
Dialing Planis not working
Inter Digit Timer expired !
Making a Call with Analog CO
Inter Digit Timer
1-15s
1-15s
- PBX can know the end of dialing by Dialing Plan Table.
- It works for ISDN Enblock dial mode and Analog CO.
- Typical configuration by “Auto Assign”. (Type A/B/C/D/E)- Dialing Plan Table is assigned for each TRG.
- PBX sends all of the dialed digits at once after all digits dialed.
Dialing Plan
Confidential 30
It overrides CLIR / CO Line CLIP.Ext.CLIP is sent to PRI public network as “Location Identification Number”,even if CLIR is set or CLIP mode is “CO Line CLIP”.
-This feature works only for Emergency call.- “E911 service” must be enabled.
Yes
Ext. CLIP sending on Emergency Call
Confidential 31
[Auto] + [JOG] or [Navi-Down/UP] works as short cut key. --- TDA30 V1.0 too
- TDA100/200 Ver.1.0
“AUTO DIAL”
Nothing Happens
- TDA100/200 Ver.1.1 (TDA30 Ver.1.0)
“AUTO DIAL”System Directory
Name ?>
“” or “” Allen, DavidAllen, SteveAzure, Alf
“ENTER” Daly, GillDarcy, NigelDavies, Allan
Short Cut Access to System Speed Dial
Confidential 32
Function – Receiving Calls
- Modified DDI Number is displayed on LCD
- Disable DSS Flash
Confidential 33
- TDA100/200 Ver.1.0
- TDA100/200 Ver.1.1
ISDN4772111 (CLIP)Line 001:201 (DDI)
Caller 4772111 Ext. 201:DDI 654201
654201 201
4772111 (CLIP)Line 001:654201 (DDI)
DDI TableDIL Table & Port setting
ISDN
Ext. 201:DDI 654201
201654201
Caller 4772111
Modified DDI Number is displayed on LCD
Confidential 34
- TDA100/200 Ver.1.0
Ext. 201
External Call to Extension directly
The DSS LED on Ext.202 is flashing.The call can be picked up by pressing the button.
- TDA100/200 Ver.1.1Two options:- The DSS LED on Ext.202 will flash. The call can be picked up by pressing the button. - The DSS LED on Ext.202 will turn ON. The call cannot be picked up by pressing the button.
Busy tone is sent if the DSS button is pressed.
External Call
New program item
Enable : DSS LED will flash
Disable : DSS LED will turn ON
All DSS LED’s flashing look like a Xmas tree. Annoying!!!
Ext. 202
201
Improved DSS LED flashing/Pick up call -1
Confidential 35
- TDA100/200 Ver.1.0
External Call to ICD-Group directly
The DSS LED on Ext.202 flashes.The call can be picked up by pressing the button.
- TDA100/200 Ver.1.1Two options:- The DSS LED on Ext.202 will flash. The call can be picked up by pressing the button. - The DSS LED on Ext.202 will turn ON. The call cannot be picked up by pressing the button.
Busy tone is sent if the DSS button is pressed.
New item
Enable : DSS LED will flash
Disable : DSS LED will turn ON
Ext. 201 Ext. 202
201External Call
ICD-G 280
Improved DSS LED flashing/Pick up call -2
Confidential 36
It is possible to disable DSS LED’s turning off for an incoming call.
New itemON or Flash : DSS LED turns ON or flashes for an incoming call. OFF : DSS LED never turns ON nor flashes for an incoming call.
If the DSS button is pressed when extension is ringing,
Busy Tone
LED : ON
It is possible to pick up call
LED: Flashing
Call pick up by DSS key = Disable
Call pick up by DSS key = Enable
DSS Key mode = ON
DSS Key mode = OFF Call arrives at extension
LED: OFF
Improved DSS LED flashing/Pick up call -3
Confidential 37
Function – Hold/FWD/TR
- Disable Hold Recall
- Disable re-count Ext-CO Duration Limitation
Confidential 38
Disable Hold Recall is available if Hold Recall Timer is 0.
1-240: Hold Recall works0 : does not work V1.0 does not have.
Disable Hold Recall
Confidential 39
Disable re-count Ext-CO Duration Limitation by Hold Retrieve
Extn-CODuration Timer
Calling Party Called Party
Call dest. Party
Place on Hold
Hold Retrive
Answer
Ringing(Establishing a Call)
(In Conversation)
(On Hold to transfer)
(In Conversation)
Tim
e fl
ow Start
ReStart
StartV1.0 V1.1
- Ext 201 makes an external call. - Extension-CO duration timer on Ext 201 starts when the external party answers the call.- Ext 201 transfers the call to Ext 202.
Extension-CO duration timer on Ext 202 re-starts when Ext 202 answers the call.
Extension-CO duration timer on Ext 201 continues on Ext 202.
V1.0
V1.1
Concrete example
Disable Re-counting Ext-CO Duration Timer
Confidential 40
Function – Conference
- ISDN – 3 party Conference
- DTMF Tone through a Conference from PT
Confidential 41
2nd Party
1st Party
Adding a Third Party during a conversation using an ISDNservice (Three-party Conference [3PTY] via ISDN)
Standard : ETS 300 188
New
ISDN
It is not service item for Euro-ISDN
ISDN – 3 Party Conference (EURO-ISDN) -1
Confidential 42
How to establish a conference (During a conversation)
Press ISDN-Hold
ISDN-Hold
Dial desired phone
number
Talk to the new party
3-party conference
Press CONF
Dial desired phone
number
Talk to the new party
3-party conference
Press Transfer
Press Transfer
PT/PS
PT/PS
Enter
Enter
ISDN – 3 Party Conference (EURO-ISDN) -2
Confidential 43
- This will be useful for two parties to listen to VM message.
SLTSLT
Voice MailVoice Mail
PTPT
( Conference )
DTMFTone
DTMFTone
Not only SLT user but also PT usercan control Voice Mail.
Voice Mail control during conference call.
SLT
PT
YES(Can send DTMF)
NO(Cannot send DTMF)
YES(Can send DTMF)
YES(Can send DTMF)
V1.0 V1.1
DTMF Tone Through to Conf.Call from PT
Confidential 44
Function – Timer
- Intercept Timer for each time mode
Confidential 45
Intercept timer and DISA intercept timer can be programmed for each time service mode.
Intercept Timer for Day / Lunch / Break / Night
Intercept Timer
DISA Intercept Timer
1-60 s : Enable0 s : Disable
1-240 s
Intercept Timer For Each Time Mode
Confidential 46
Function – Others
- SMDR RC/AN Information Output
- Paging to Another Paging Group
Confidential 47
RC (Receive Call) information, it will be output when TDA receives incoming call.
AN (Answer Call) information, it will be output when extension user answered incoming call.
* SMDR Type format is not changed from V1.0 (Type A / B / C).
* KX-TD SMDR based application can work.
* But some of them can not work properly. Because the detailed Spec. and timing to output is not same as KX-TD series.
Programming is needed.
-No Print (Default)-Print
SMDR RC/AN Information Output -1
Confidential 48
Output Samples-1
20/02/04 07:48AM 201 01 <I>203 RC20/02/04 07:49AM 201 01 <I>203 0'56 00:00'00 NA
- External Call Extension (201) No answer Caller disconnects
20/02/04 08:22AM 201 01 <I>203 RC20/02/04 08:22AM 201 01 <I>203 0'11 AN Ext. 201 Answers 20/02/04 08:22AM 201 01 <I>203 0'11 00:00'17
- External Call Extension (201) Answers Disconnects
- External Call DISA (270) OGM is sent No Answers Caller disconnects 20/02/04 09:00AM 270 01 <I>203 RC20/02/04 09:00AM 270 01 <I>203 0'05 AN DISA Answers 20/02/04 09:01AM 270 01 <I>203 0'05 00:00'19 D0
20/02/04 09:04AM 270 01 <I>203 RC20/02/04 09:04AM 270 01 <I>203 0'05 AN DISA Answers20/02/04 09:05AM 270 01 <I>203 0'05 00:00'09 D0 Ext. 201 Answers 20/02/04 09:05AM 201 01 <I>203 0'00 00:00'12 TR
- External Call DISA (270) OGM is sent Ext. 201 answers Disconnects
Output Samples-2 (DISA)
SMDR RC/AN Information Output -2
Confidential 49
- External Call ICD-G (280) Time table is not started No Answers Caller disconnects Output Samples-3 (ICD-G)
20/02/04 08:42AM 280 01 <I>203 RC20/02/04 08:42AM 280 01 <I>203 0'05 00:00'00 NA
20/02/04 08:36AM 280 01 <I>203 RC20/02/04 08:37AM 280 01 <I>203 0'10 AN Time table starts 20/02/04 08:37AM 280 01 <I>203 0'10 00:00'19
-External Call ICD-G (280) Wait Time table starts No Answers Caller disconnects
- External Call ICD-G (280) Time table is not started Ext.201 Answers Disconnect
20/02/04 08:49AM 280 01 <I>203 RC20/02/04 08:49AM 280 01 <I>203 0'04 AN Ext. 201 Answers 20/02/04 08:49AM 280 01 <I>203 0'04 00:00'0020/02/04 08:49AM 201 01 <I>203 0'00 00:00'06
-External Call ICD-G (280) Wait Time table starts Ext.201 Answers Disconnect
20/02/04 10:48PM 280 01 <I>203 RC20/02/04 10:48PM 280 01 <I>203 0'05 AN Time table starts20/02/04 10:48PM 280 01 <I>203 0'05 00:00'12 Ext.201 Answers 20/02/04 10:48PM 201 01 <I>203 0'00 00:00'06
- External Call ICD-G (280) Time table starts No Answers Caller disconnects
20/02/04 10:57PM 280 01 <I>203 RC20/02/04 10:57PM 280 01 <I>203 0'00 AN Time table starts 20/02/04 10:57PM 280 01 <I>203 0'00 00:00'17
SMDR RC/AN Information Output -3
Confidential 50
- No additional programming steps are required.
- Operation is not changed from V1.0. ( [*33]+[PageG.Number(2digits)] )
- TDA100/200 Ver.1.0
Ext. 201
User Group-01
Ext. 202
User Group-02
Paging Group-01
Ext. 203
User Group-03
Ext. 204
User Group-04
Paging Group-02
NO
NOYES YES
- TDA100/200 Ver.1.1
Ext. 201
User Group-01
Ext. 202
User Group-02
Paging Group-01
Ext. 203
User Group-03
Ext. 204
User Group-04
Paging Group-02
YES
YES
YES YES
Paging to Another Paging Group
Confidential 51
Function – Programming
- Programmable COS Name & CS Name
- Ext. CLIP Automatic Generating
- DDI/DID Name Automatic Generating
- Wireless XDP Programming from PC
Confidential 52
- TDA100/200 Ver.1.0 - TDA100/200 Ver.1.1COS name
CS name
Both 20 Characters
Programmable COS Name & CS Name
Confidential 53
CLIP: 345 01 55345
55
1
201
2001Delete digit
345015534502553450355
Increase this number
New function
=> Delete from left
0- 4 1 - 999
Max. 16 digits,( 0 – 9 * # )
Max. 16 digits,( 0 – 9 * # )
Ext. CLIP Automatic Generating
Confidential 54
PCC00-UKPCC
-UK
3
1
2000
12300123011230212303
Delete digit
Increase thisnumber
PCC00-UKPCC01-UKPCC02-UKPCC03-UK
New function
1 - 1000
1 - 1000
0 - 32
Max. 20 characters
Max. 20 characters
=> Delete from left
DDI/DID Name Automatic Generating
Confidential 55
It is possible to program Wireless XDP connection from the PC maintenance console.
- Assign Wireless XDP PS number.
- Click “Apply”
- Power off-on the Wireless XDP PS for enabling this programming.
Wireless XDP Programming from PC
Confidential 56
Improvement
- Logical Check
- PS Hand-over during Conference Call
- Walking Extension from Fault Extension
Confidential 57
1. System - System Operator PBX-Operator2. Feature - Tenant Operator3. Groups - Incoming Call Distribution Group - Group Setting Supervisor
Extension4. Groups - Incoming Call Distribution Group - Member Extension No.5. Groups - Idle Extension Hunting Group Member Extension6. Groups - Voice (DTMF) Group - Group Information Extension Number of
the SLT Port Connected to VM
7. Extension - Wired Extension/Portable Station - Extension Settings Transfer Recall Destination
8. Optional Device - DISA - Message Setting 1 Digit AA Destination
9. Feature - Speed Dial & Caller ID - Main Table CLI Destination10. CO & Incoming Call - DIL Table & Port Setting DIL Destination11. CO & Incoming Call - DDI/DID Table DDI/DID Destination12. CO & Incoming Call - MSN Table MSN Destination13. Maintenance - Miscellaneous Local Alarm Display
Extension
The following extension assignment logical check function is deleted from the V1.1 PC-Soft.
In programming an extension number that does not exist, the system will now accept.
Logical Check -1
Confidential 58
What happens?
- TDA100/200 Ver.1.0
- TDA100/200 Ver.1.1
1- Open the PC maintenance tool and go to 2.System Operator then 2. PBX Operator
2- Click “Apply”
1- Open the PC maintenance2- Go to 2.System Operator 2. PBX Operator3- Click “Apply”
Dealer does not know what is wrong!
Nothing happens.
Please remember, when programming extension numbers that do not exist, that the system will now accept the entry.
Logical Check -2
Confidential 59
If we program a non-existing number ??1. PBX-Operator OUS mode Extension.2. Tenant Operator OUS mode Extension.3. Supervisor Extension No Supervisor Extension4. ICD Group Member The TDA skips this extension.5. Idle Extension Hunting Group Member The TDA skips this extension.6. VM (DTMF) Group VM function does not work.7. Transfer Recall Destination The transfer recall goes back to
the transferring Extension.8. 1 Digit AA Destination The TDA sends the re-order tone.9. CLI/DIL/DDI/DID/MSN Destination The TDA checks the following…
10. Local Alarm Display Extension No Alarm Extension.
- Re-order tone
- Re-routed to operator
Logical Check -3
Confidential 60
Handover can be made during Conference Call.
- Both of 2.4GHz model and DECT model- No programming required
PS Hand-over during Conference Call
Confidential 61
A “Fault” extension card can be used for walking extensions.
Insert and remove a card, the non connected extensions can be used for walking extensions.DHLC-8 24 extensionsSLC-8 8 extensionsDLC-8/SLC16 16 extensionsDLC-16 32 extensions
Walking Extension from Fault Extension -1
Confidential 62
Ext 201
Ext 233 Part-time worker - A 8:00-12:00Ext 234 Part-time worker - B 12:00-16:00Ext 235 Part-time worker - C 16:00-20:00Ext 236 Part-time worker - D 20:00-8:00
One existing extension can be shared to several users with different extension number.What is benefit ?
What is Walking Extension access code? *727 + Extension number + PIN
Walking Extension from Fault Extension -2
Confidential 63
To Start TDA100/200 V1.1
- PC Maintenance Console Compatibility
- Data Conversion
- Upgrade PBX
Confidential 64
TDA100/200 Ver.1.1 PC maintenance console can maintain TDA100/200 Ver.1.0 PBX, too.
Initial screen When we access TDA100/200 Ver.1.0
Automatically
PC Maintenance Console Compatibility
Confidential 65
Data Conversion
DSYS-1.1
PC maintenance console provides a data convert function. (DSYS Ver.1.0 to DSYS Ver.1.1)
1- Open the PC Maintenance console and open the saved DSYS (Ver 1.0).
DSYS 1.0
3- Enter new file name and click “Save”
2- Click
DSYS 1.1
Confidential 66
Upgrade PBX1. Prepare following files
- PMPR 1.1, DLNG0 1.1, DLNG1 1.1- DSYS 1.1 --- Converted DSYS or New DSYS created by PC-Soft
2. Download above files to PBX
3. Reset PBX by command- V1.0054 or later --- Please select PMPR_SUB, DSYS_SUB, then reset- Before V1.0054 --- Please reset without any care.
Select
Select
4.Connect PC-Soft again and download other files as PC-Soft’s dialog box saying.
5.If PC-Soft require reset, reset PBX again, then you can finish upgrading.
Confidential 67
Thank you very much !Thank you very much !