compact hifi system nv-500 nv-600manual.kenwood.com/files/b60-4290-00.pdfcompact hifi system nv-500...

COMPACT HIFI SYSTEM

NV-500NV-600

This instruction manual is used to describe multiple models listed above.

Model availability and features (functions) may differ depending on the country

and sales area.

INSTRUCTION MANUALKENWOOD CORPORATION

B60-4290-00

DIGITAL AUDIO

COMPACT

TEXT

EN

2

Prep

arat

ion

sect

ion

MONITOROUT

REC OUT PLAY IN PLAY INVIDEO 1VIDEO 1

AUDIO

REC OUT

PLAY IN

PLAY IN

FM75Ω

GND AM

VIDEO 1

AC 110–120V

VIDEO 2

VIDEO 2

L

R

ANTENNA

DIGITALOUT

OPTICAL

AC 220– 240V

AC 110–120V

AC 220– 240V

+

-

+

-

FRONTSPEAKERS

(6 - 16Ω)SUPER

WOOFERPRE OUT

LR

AC 110–120V

AC 220– 240V

AC 110–120V

AC 220– 240V

Before applying powerUnits are designed for operation as follows.

U.S.A. and Canada ............................................ AC 120 V onlyAustralia ............................................................. AC 240 V only

The marking is located on the rear panel and says that thecomponent uses laser beams that have been classified asClass 1. It means that the unit is utilizing laser beams that areof a weaker class. There is no danger of hazardous radiationoutside the unit.

CLASS 1LASER PRODUCT

The marking of products using lasers(Except for some areas)

Caution : Read this page carefully to ensure safe operation.

For the United KingdomFactory fitted moulded mains plug

1. The mains plug contains a fuse. For replacement, use onlya 13-Amp ASTA-approved (BS1362) fuse.

2. The fuse cover must be refitted when replacing the fuse inthe moulded plug.

3. Do not cut off the mains plug from this equipment. If theplug fitted is not suitable for the power points in your homeor the cable is too short to reach a power point, then obtainan appropriate safety approved extension lead or adapter,or consult your dealer.If nonetheless the mains plug is cut off, remove the fuseand dispose of the plug immediately, to avoid a possibleshock hazard by inadvertent connection to the mains sup-ply.

IMPORTANT:The wires in the mains lead are coloured in ac-cordance with the following code:

Blue : NeutralBrown : Live

Do not connect those leads to the earth terminal of a three-pin plug.

Europe and U.K. ................................................. AC 230 V only*Other countries ...........AC 110-120 / 220-240 V switchable

*AC voltage selection

The AC voltage selector switches on the rear panel are set tothe voltage that prevails in the area to which the unit is shipped.Before connecting the power cord to your AC outlet, makesure that the setting position of this switch matches your linevoltage. If not, it must be set to your voltage in accordancewith the following direction.

AC voltage selector switch

Move switch levers to match your line volt-age with a small screwdriver or otherpointed tool.

Note:Our warranty does not cover damage caused by excessiveline voltage due to improper setting of the AC voltage selec-tor switch.

Safety precautionsWARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE

TO RAIN OR MOISTURE.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVECOVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVIC-ING TO QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCKDO NOT OPEN

THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE,IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLT-AGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TOCONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.

THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THEUSER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) IN-STRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.

CAUTION

3

Preparation section

Contents

Before applying power ............................................ 2Safety precautions ........................................................... 2IMPORTANT SAFEGUARDS ..................................... 4Special features ................................................................. 6In regard to demonstration ............................................... 6Accessories ........................................................................ 6

System connection ......................................................... 7AM loop antenna connection .......................................... 7FM antenna connection .................................................... 7Connection of the speaker system ................................ 8Connection of Other Accessories ................................... 9

CHANNEL SPACE setting ............................................. 10Controls and indicators ................................................ 11Operation of remote control unit ................................ 12

Basic configuration of the remote control menu....... 13Selecting an input using the CURSOR key .................. 13

Clock adjustment .......................................................... 14

Let's put out some sound ............................................. 16Basic use method............................................................. 16Receiving broadcast station .......................................... 18To receive a station that has not been preset ............ 19Collective presetting of stations (auto preset)(Except for Europe and U.K.)Presetting R.D.S. stations(RDS auto memory for Europe and U.K. ) ......................................... 20One-by-one presetting (manual preset) ................................. 21Playback of CD ................................................................. 22In regard to CD-TEXT ....................................................... 23Playback of tape............................................................... 24Selecting Dolby NR.......................................................... 25Selecting the reverse mode ........................................... 25

Let's recording ............................................................... 26Recording on TAPE .......................................................... 26CD synchronized recording ............................................ 27

Caution : Read the pages marked carefully to ensure safe operation.

Before applying power

Knowledge section

Basic section

Preparation section Application sectionR.D.S. (Radio Data System) (for Europe and U.K.) ............................ 28

Searching for a desired program type (PTY search) ...... 29To be able to listen to the desired informationat any time (EON).............................................................. 30

Playback of CD .............................................................. 32Listening in the desired sequence (program playback) ...... 32Repeated playback .......................................................... 34Listening to an unexpected title sequence(random playback) ...........................................................35

Convenient Recording Methods ................................. 36Selection of the Recording Type ................................... 36Recording an entire CD onto tape (CD direct recording) .......................................................................... 37Recording every desired track in CD onto tape(CD one-track recording) .................................................................... 38Recording desired CD tracks in a desired orderonto tape (CD program recording) ................................................ 39

Tone control and sound field effect adjustment ...... 40Adjusting the external input level ................................ 40Adjusting the subwoofer output level ......................... 40Bass Boost and tone control .......................................... 41Dolby Virtual setting ........................................................42DSP mode setting ............................................................. 43

Timer operation ............................................................. 44Setting the O.T.T. ............................................................... 44Setting the timer playback .............................................45Sleep Timer (Sleep) ......................................................... 46Timer recording ................................................................47

Checking the time information display of CD .......... 48Adjusting the display contrast .................................... 49Remote control of external components .................. 50

Important Items .............................................................. 54Maintenance ..................................................................... 54Reference .......................................................................... 54Disc handling precautions .............................................55Notes on cassette tape ................................................... 55

In case of difficulty ................................................................57INDEX .............................................................................. 60Specifications ................................................................ 62

4

Prep

arat

ion

sect

ion

Caution : Read this page carefully to ensuresafe operation.IMPORTANT SAFEGUARDS

6. Temperature – The appliance may not functionproperly if used at extremely low, or freezingtemperatures. The ideal ambient temperature isabove +5°C (41°F).

7. Heat – The appliance should be situated away fromheat sources such as radiators, heat registers, stoves,or other appliances (including amplifiers) that produceheat.

8. Electric shock – Care should be taken so that objectsdo not fall and liquid is not spilled into the enclosurethrough openings. If a metal objects, such as a hairpin or a needle, comes into contact with the inside ofthis appliance, a dangerous electric shock may result.For families with children, never permit children toput anything, especially metal, inside this appliance.

9. Enclosure removal – Never remove the enclosure.If the internal parts are touched accidentally, a seriouselectric shock might occur.

10.Magnetic fields – Keep the appliance away fromsources of magnetic fields such as TV sets, speakersystems, radios, motorized toys or magnetizedobjects.

11.Cleaning – Unplug this appliance from the walloutlet before cleaning. Do not use volatile solventssuch as alcohol, paint thinner, gasoline, or benzine,etc. to clean the cabinet. Use a clean dry cloth.

12.Accessories – Do not place this appliance on an unstablecart, stand, tripod, bracket, or table. The appliance may fall,causing serious injury to a child or adult, and seriousdamage to the appliance. Use only with a cart, stand,tripod, bracket, or table recommended by the manufacturer,or sold with the appliance. Any mounting of the applianceshould follow the manufacturer’s instructions, and shoulduse a mounting accessory recommended by themanufacturer. An appliance and cart combination shouldbe moved with care. Quick stops, excessive force, anduneven surfaces may cause the appliance and cartcombination to overturn.

Please read all of the safety and operating instructionsbefore operating this appliance. Adhere to all warnings onthe appliance and in the instruction manual. Follow all thesafety and operating instructions. These safety andoperating instructions should be retained for futurereference.

1. Power sources – The appliance should be connected toa power supply only of the type described in the instructionmanual or as marked on the appliance. If you are not sureof the type of power supply to your home, consult yourappliance dealer or local power company. For appliancesintended to operate from battery power, or other sources,refer to the instruction manual.

2. Power-cord protection – Power-supply cords shouldbe routed so that they are not likely to be walked onor pinched by items placed upon or against them,pay particular attention to cords at plugs, conveniencereceptacles, and the point where they exit from theappliance.

3. CAUTION – Polarization – This appliance may

be equipped with a polarized alternating-current line plug (aplug having one blade wider than the other). This plug willfit into the power outlet only one way. This is a safetyfeature. If you are unable to insert the plug fully into theoutlet, try reversing the plug. If the plug should still fail tofit, contact your electrician to replace your obsolete outlet.Do not defeat the safety purpose of the polarized plug.

4. Ventilation – Slots and openings in the cabinet areprovided for ventilation and to ensure reliable operation ofthe appliance and to protect it from overheating, and theseopenings must not be blocked or covered. The applianceshould be situated so that its location or position does notinterfere with its proper ventilation.To maintain good ventilation, do not put records or a table-cloth on the appliance. Place the appliance at least 10 cmaway from the walls.Do not use the appliance on a bed, sofa, rug or similarsurface that may block the ventilation openings. Thisappliance should not be placed in a built-in installation suchas a bookcase or rack unless proper ventilation is providedor the manufacturer’s instructions have been adhered to.

5. Water and moisture – The appliance should not beused near water - for example, near a bathtub,washbowl, kitchen sink, laundry tub, in a wetbasement, or near a swimming pool, etc.

Never pull or stretchthe cord.

5

Preparation section

13.Lightning – For added protection for this appliance duringa lightning storm, or when it is left unattended and unusedfor long periods of time, unplug it from the wall outlet anddisconnect the antenna or cable system. This will preventdamage to the appliance due to lightning and power-linesurges.

14.Abnormal smell – If an abnormal smell or smoke isdetected, immediately turn the power OFF and unplugthe appliance from the wall outlet. Contact your dealer ornearest service center.

15.Damage requiring service – The appliance shouldbe serviced by qualified service personnel when:A. The power-supply cord or the plug has beendamaged.B. Objects have fallen, or liquid has been spilled intothe appliance.C. The appliance has been exposed to rain or water.D. The appliance does not appear to operate normallyby following the instruction manual. Adjust only thosecontrols that are covered by the instruction manual as animproper adjustment of other controls may result in damageand will often require extensive work by a qualifiedtechnician to restore the appliance to its normal operation.E. The appliance has been dropped, or the enclosuredamaged.F. The appliance exhibits a marked change in performance.

16.Servicing – The user should not attempt to servicethe appliance beyond that described in the instructionmanual. All other servicing should be referred toqualified service personnel.

17.Outdoor antenna grounding – If an outside antennais connected to the appliance, be sure the antennasystem is grounded so as to provide some protectionagainst voltage surges and built up static charges.Article 810 of the National Electrical Code ANSI/NFPA 70, provides information with respect to propergrounding of the mast and supporting structure,grounding of the lead-in wire to an antenna dischargeunit, size of grounding conductors, location of antennadischarge unit, connection to grounding electrodes,and requirements for the grounding electrode. SeeFigure.

18.Power lines – An outside antenna system should not belocated in the vicinity of overhead power lines or otherelectric light or power circuits, or where it can fall into suchpower lines or circuits. When installing an outside antennasystem, extreme care should be taken to keep fromtouching such power lines or circuits as contact with themmight be fatal.

19.AC outlets – Do not connect other audio equipmentwith a power consumption larger than that specifiedto the AC outlet on the rear panel. Never connectother electrical appliances, such as an iron or toaster,to it to prevent fire or electric shock.

20. Overloading – Do not overload wall outlets, extensioncords, or integral convenience receptacles as this canresult in a risk of fire or electric shock.

21. Attachment – Do not use attachments not recommendedby the appliance manufacturer as they may cause hazards.

22. Replacement parts – When replacement parts are required,be sure the service technician has used replacement partsspecified by the manufacturer or have the samecharacteristics as the original parts. Unauthorizedsubstitutions may result in fire, electric shock, or otherhazards.

23. Safety check – Upon completion of any service or repairsto this appliance, ask the service technician to performsafety checks to determine that the appliance is in properoperating condition.

Notes:1. Item 3 is not required except for grounded or polarized equipment.2. Item 17 and 18 are not required except for units provided with

antenna terminals.3. Item 17 complies with UL in the U.S.A.

EXAMPLE OF ANTENNA GROUNDING AS PERNATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDINGELECTRODE SYSTEM(NEC ART 250, PART H)

NEC – NATIONAL ELECTRICAL CODE

GROUNDING CONDUCTORS(NEC SECTION 810-21)

ANTENNALEAD IN WIRE

ANTENNADISCHARGE UNIT(NEC SECTION 810-20)

GROUND CLAMP

ELECTRICSERVICEEQUIPMENT

GROUNDCLAMPS

Caution : Read this page carefully to ensure safe operation. IMPORTANT SAFEGUARDS

6

Prep

arat

ion

sect

ion

Special features

UnpackingUnpack the unit carefully and make sure that all accessories are put aside so they will not be lost.Examine the unit for any possibility of shipping damage. If your unit is damaged or fails to operate, notify your dealer immediately.If your unit was shipped to you directly, notify the shipping company without delay. Only the consignee (the person or companyreceiving the unit) can file a claim against the carrier for shipping damage.We recommend that you retain the original carton and packing materials for use should you transport or ship the unit in the future.

Keep this manual handy for future reference.

In regard to demonstrationThis unit is equipped with a demonstra-

tion function (only display). The demon-

stration consists of sequential change of

display and indicators showing the op-

erations, but the audio itself does not

change. The demonstration function can

be cancelled as follows.

Before applying power

Accessories

FM indoor antenna (1) Loop antenna (1) Remote control unit (1)

Batteries (R6/AA) (6)

Please confirm that the following accessories are present.

*AC plug adaptor (1)

*Use to adapt the plug on the powercord to the shape of the wall outlet.(Accessory only for regions whereuse is necessary.)

To switch over the demonstration:

Switch power ON before the following

operation.

To cancel the demonstration mode:

Press the CONFIRM/DEMO key.To start the demonstration mode:

Press and hold the CONFIRM/

DEMO key for about 2 seconds.

÷ The setting is remembered even when the power is switched off.÷ This operates automatically when a power failure has occurred or the plug of the power cable has been pulled while

the power was ON. Cancellation is possible by pressing the key during the demonstration.

CONFIRM/DEMO

Bidirectional remote control unit with play mode display at hand

The bidirectional remote uses a large-sized display for easy-to-see, simple operations.

Dolby Virtual SurroundThe Dolby Virtual Surround function provides realistic surround effect through only twoloudspeakers.

High output power with large headroom

High, 100 W + 100 W power amplifier enables powerful musical reproduction. (NV-500)

Leave the remote control unit attached tothe main unit during operation. @

7

Preparation section

System connection

AM loop antenna connectionThe supplied antenna is for indoor use. Placeit as far as possible from the main system,TV set, speaker cords and power cord, andset it to a direction which provides the bestreception.

FM indoor antenna connectionThe accessory antenna is for temporary in-door use only. For stable signal receptionwe recommend using an outdoor antenna.Remove the indoor antenna if you connectone outdoors.

1 2 3

AM loop antenna connection

FM antenna connection

1 Connect to the antenna terminal.

2 Locate the position providing good

reception condition.

3 Fix the antenna.

FM outdoor antennaLead the 75Ω coaxial cable connected tothe FM outdoor antenna into the room andconnect it to the FM 75Ω terminal.

Antenna adapter(Commercially-available)

+

-

+

-

MONITOROUT

REC OUT PLAY IN PLAY INVIDEO 1VIDEO

AUDIO

REC OUT

FRONTSPEAKERS

(6 - 16Ω)SUBWOOFER

(4 - 16Ω)

PLAY IN

PLAY IN

FM75Ω

GND AM

VIDEO 1

AC 110–120V

VIDEO 2

VIDEO 2

L

R

LR

ANTENNA

DIGITALOUT

OPTICAL

AC 220– 240V

AC 110–120V

AC 220– 240V

FM75Ω

GND AM

ANTENNA

+

-

+

-

MONITOROUT

REC OUT PLAY IN PLAY INVIDEO 1VIDEO 1

AUDIO

REC OUT

FRONTSPEAKERS

(6 - 16Ω)SUBWOOFER

(4 - 16Ω)

PLAY IN

PLAY IN

FM75Ω

GND AM

VIDEO 1

AC 110–120V

VIDEO 2

VIDEO 2

L

R

LR

ANTENNA

DIGITALOUT

OPTICAL

AC 220– 240V

AC 110–120V

AC 220– 240V

+

-

+

-

MONITOROUT


AUDIO

REC OUT

FRONTSPEAKERS

(6 - 16Ω)SUBWOOFER

(4 - 16Ω)

PLAY IN

PLAY IN

FM75Ω

GND AM

VIDEO 1

AC 110–120V

VIDEO 2

VIDEO 2

L

R

LR

ANTENNA

DIGITALOUT

OPTICAL

AC 220– 240V

AC 110–120V

AC 220– 240V

FM75Ω

GND AM

ANTENNA

FM75Ω

GND AM

ANTENNA

POWER cordTO WALL AC

OUTLET

8

Prep

arat

ion

sect

ion

Connection of the speaker system

NV-600

+

-

+

-

MONITOROUT


AUDIO

REC OUT

FRONTSPEAKERS

(6 - 16Ω)SUBWOOFER

(4 - 16Ω)

PLAY IN

PLAY IN

FM75Ω

GND AM

VIDEO 1

AC 110–120V

VIDEO 2

VIDEO 2

L

R

LR

ANTENNA

DIGITALOUT

OPTICAL

AC 220– 240V

AC 110–120V

AC 220– 240V

+

-

+

-

R LFRONT

SPEAKERS(6 - 16Ω)

SUBWOOFER(6 - 16Ω)

• Never short-circuit the + and – speaker cords.• If the left and right speakers are connected inversely or if the speaker cords are connected with reversed polarity, the sound

becomes unnatural with ambiguous acoustic image positioning. Be sure to connect the speakers and speaker cords correctly.

NV-500

MONITOROUT


AUDIO

REC OUT

PLAY IN

PLAY IN

FM75Ω

GND AM

VIDEO 1

AC 110–120V

VIDEO 2

VIDEO 2

L

R

ANTENNA

DIGITALOUT

OPTICAL

AC 220– 240V

AC 110–120V

AC 220– 240V

+

-

+

-

FRONTSPEAKERS

(6 - 16Ω)SUPER

WOOFERPRE OUT

LR

+

-

+

-

R LFRONT

SPEAKER(6 - 16Ω)

Bassreflexspeakersystem

Bas

sre

flex

spea

ker

syst

em

Do not plug the power cord into the power outlet untilall of the required connections have been made.

Malfunction of microcomputerIf operation is not possible or erroneous display appears

even though all connections have been made properly, re-

set the microcomputer referring to “In case of difficulty”. ¨U

1 2 3 1 2 3Main Unit

Twist

Speakersystem

Twist

Speakers front view

Speakers front view

Connect only provided main unit.

Connect only provided main unit.

Speaker (left)Speaker (right)

Speaker (left)Speaker (right)

System connection

9

Preparation section

Connection of Other Accessories (Commercially Available Parts)

MONITOROUT


AUDIO

REC OUT

PLAY IN

PLAY IN

FM75Ω

GND AM

VIDEO 1

AC 110–120V

VIDEO 2

VIDEO 2

L

R

ANTENNA

DIGITALOUT

OPTICAL

AC 220– 240V

AC 110–120V

AC 220– 240V

+

-

+

-

FRONTSPEAKERS

(6 - 16Ω)SUPER

WOOFERPRE OUT

LR

MONITOROUT

REC OUT PLAY IN PLAY INVIDEO 1

VIDEO

AUDIO

REC OUT

PLAY IN

PLAY IN

VIDEO 1 VIDEO 2

VIDEO 2

L

R

SUPERWOOFERPRE OUT

DIGITALOUT

OPTICAL

DIGITAL OUT jack(OPTICAL)

If necessary, remove the

cap and plug the optical-

fiber cable (optional)

Cap

Optical-fibercable

Optical-fiber cable

MD recorder or DAT etc.

Monitor TVVideo Input

Video deck

DVD player or LD player Audio output

Video output

Video outputVideo input

Audio inputAudio output

Powered subwoofer

Only for NV-500

System connection

CAUTIONBe sure to adhere followings. Or proper ventilation will be blocked causing damage or fire hazard.

÷ Do not place any objects impairing heat radiation onto the top of unit.

For U.S.A. and Canada

CAUTIONBe sure to adhere followings. Or proper ventilation will be blocked causing damage or fire hazard.

÷ Do not place any objects impairing heat radiation onto the top of unit.

÷ Leave a space around the unit (from the largest outside dimension including projection) equal or greater

than, shown below.

Back panel : 10 cm

For other countries

10

Prep

arat

ion

sect

ion

The space between radio channels has been set to the onethat prevails in the area to which the system is shipped.However, if the current channel space setting does notmatch the setting in the area where the system is to be used,for instance when you move from area 1 or area 2 shown inthe following table or vice versa, proper reception of AM/FMbroadcasts cannot be expected. In this case, change thechannel space setting in accordance with your area by refer-ring to the following table.

CHANNEL SPACE setting (Except for the U.S.A., Canada, U.K., Europe and Australia)

CHANNELSPACE freq.Area

1

2

USA, Canada and SouthAmerican countries

Other countries

FM : 100 kHzAM : 10 kHz

FM : 50 kHzAM : 9 kHz

CURSOR

SET

STOP

1 Attach the remote controlunit to the main unit

@

2 Switching the power ON

3 Select the TUNER input.

4 Press and hold the STOP (7)key for about 2 seconds.

5 Select the message to bedisplayed, "FM 100kHz" or"FM 50kHz".

STANDBY/TIMER

ON/STANDBY

CURSOR

SET

TVVIDEO1VIDEO2

CDTUNERTAPE

FUNCTION

7

INPUT

÷ The setting is remembered even when the power isswitched off.

11

Preparation section

Controls and indicators

CD

CD6

TAPE2 3 MUTE

TUNER TAPE MUTE

ACTIVE

TUNER/BAND

STOP

ON/STANDBY

STANDBY/TIMER

VOLUME

STEREO

0

PHONES

PUSH OPEN

1

1

2

3

4

5

6

78

90

!

POWERON/STANDBY

STANDBY/TIMER

@#

TVVIDEO1VIDEO2

CDTUNERTAPE

FUNCTION

^

%$

VOLUME CONTROL

CLOCK/LIGHT MUTE

CONFIRM/DEMO

HOMEIR ON/STANDBY

BAND INPUT DIRECTION

SET ENTER

¶REC

– P.CALL –

CURSOR

6

7

¢ 4

¡ 1

IR POWER

&

*

(

)

¡ ™ £ ¢ ∞

§ ¶ •

ª

⁄ ¤ ¤ º

1 POWER/ON/STANDBY key$(for U.S.A and CANADA)ON/STANDBY ( ) key $(for other countries)STANDBY/TIMER indicator&

2 (CD) open/close (0) key ™3 CD tray ™4 PHONES jack &5 Remote control sensor @6 Cassette holder ¢

Press the area marked “PUSH

OPEN” to load or eject a tape.7 Remote control signal trans-

mitter @8 STOP key £9 VOLUME keys ^0 Input selector keys ^

MUTE key &! Input indicators@ Communication indicator

Blinks during communicationwith the remote control unit.

# ACTIVE indicatorLights during CD, MD or tapeplayback or tuner reception.

$ Selector display/iconShows the operations selectedwith the remote control.

% Menu/recording, editing selec-tion displayShows the selection menu, typeof recording or editing, etc.

^ Input selection displayShows the status selected onthe main unit or the input func-tion selected with the remotecontrol unit.

& VOLUME CONTROL keys ^* CLOCK/LIGHT key $( CONFIRM/DEMO key #) HOME key #¡ MUTE key &™ P.CALL/4 , ¢ keys

$*£ Stop (7) key ™¢ INPUT key £∞ ¶ REC key ¶§ DIRECTION key ¢¶ SET key #• ENTER key ¤ª CURSOR keys #º 6/BAND key *⁄ Display

¤ IR POWER ( ) key #(for U.S.A and CANADA)IR ON/STANDBY ( ) key#(for other countries)

*The displayed information is variable depending on areas.

12

Prep

arat

ion

sect

ion

Operation of remote control unit

3 Close the cover.1 Remove the cover. 2 Insert batteries.

÷ Insert six R6 (“AA”-size) batteriesfollowing the polarity indications.

Loading batteries

30° 30°

30° 30°

CLOCK/LIGHT

Operation

÷ When pressing more than one remote control keyssuccessively, press the keys securely by leaving aninterval of 1 second or more between keys.

After plugging the power cord of this unit, press

the key of the remote control unit to turn the

system ON. When the system is turned ON, press

the key of the function to be operated.

Operating range(approx.)

Remote sensor

Remote controlsignal transmitter

6 m6 m

When the remote control unit is attached to the

main unit, the power can be switched ON/OFF

only using the POWER ( ) key on the main unit.

To light the back light:(The back light is permanently on when the remote control unit isattached to the main unit with power on.)Press and hold the CLOCK/LIGHT key for

about 2 seconds.

When the remote control unit is detached fromthe main unit, it is recommended to leave thedisplay back light off in normal condition inorder to save the battery power.

NotesNotesNotes

1.The provided batteries are intended for use in operation checking, and their service life may be short.2.When the batteries are nearly exhausted, "Low Battery" appears and the remote controllable distance decreases.

In this case, replace all of the 6 batteries with new ones. (It is recommended to replace batteries with alkalinebatteries.)

3.If direct sunlight or the light of a high- frequency fluorescent lamp (inverter type, etc.) is incident to the remotesensor, malfunction may occur. In such a case, change the installation position to avoid malfunction.

Attaching/detaching the remote control unit1 Open the terminal block

cover of the main unit.Terminal block cover

2 To attach the remote controlunit to the main unit:

Attach by slightlytilting the remotecontrol unit.

3 To detach the remote control unitfrom the main unit:

Remove in theupper direction byslightly tilting theremote control unit.

To reset the remote control unit

÷ Do not touch the terminals.÷ Be sure to close the cover when

the remote control unit is detached.

The remote control unit may mal-function due to strong external noise,etc. In this case, remove all batter-ies and push the reset button with athin-tipped object. This resets the mi-crocomputer to the initial condition.

Reset button

Model : GRC-NV501 (for U.S.A. and Canada)Model : GRC-NV502 (for Europe and U.K.)Model : GRC-NV503 (for other countries)Infrared ray system

13

Preparation section

IR ON/STANDBY

CURSOR

SET

TVVIDEO1VIDEO2

CDTUNERTAPE

FUNCTION

TVVIDEO1VIDEO2

CDTUNERTAPE

FUNCTION

HOME

SET

SET

CURSOR

CURSOR

SET

TVVIDEO1VIDEO2

CDTUNERTAPE

FUNCTION

TVVIDEO1VIDEO2

CDTUNERTAPE

FUNCTION

j [ ˚

Basic configuration of the remote control menu The provided remote control unit has a large LCD

screen to allow interactive remote control operation.

A variety of operations can be remote controlled by

performing selection in the menu screens.

Screen configuration(Example when selecting the stereo mode of thetuner)

Basic screen

Shows the selected input,recording condition, etc.

Operation of remote control unit

Input selectedon the main unit

Press the SET key togo to a menu screen.

Press the CURSOR keys to moveup and down.The selected items can be re-mote controlled. The informationrelated to this item is shown onthe display.

Indicates the pres-ence of next page

Indicates the presenceof previous page

Press the CURSOR keysto select a menu item.

Press the SET key to go tothe next screen.

Select an item with the CURSOR keyand press the SET key to set theselection.

Menu screen Selection screen

: Item being selected with the CURSOR keys : Item that can be selected : Item that cannot be selected under the current

condition

How to use the HOME key

Pressing the HOME key in the mid-dle of selection returns to the basicscreen.

How to use the CONFIRM/DEMO key

The remote control unit displays information while holdingcommunications with the main unit. Pressing the CONFIRM/

DEMO key allows you to reconfirm the current situation.

Selecting an input using the CURSOR keyIt is usually the INPUT key that is used to select an input such as CD, TAPE or TUNER from the remote controlunit. However, the input to be recorded can also be selected using the CURSOR keys. Use the CURSOR keyas described below.

1 Switch power ON.

2 Press one of the CURSORkeys to select an input.

3 Press the SET key to set theselection.

4 Press the BAND key.(The input is switched asselected and the sourcestarts to play.)

IR POWER

or

14

Prep

arat

ion

sect

ion

CLOCK/LIGHT

SET

¢4 –P.CALL–

SET

CLOCK

4, ¢

SET

STANDBY/TIMER

CLOCK/LIGHT

Clock adjustment

Adjust the clock before setting the timer.

After plugging the AC cord into a power

outlet, set the time of the day as described

below.

ON/STANDBY

1. Switch power ON.If a CD or cassette has been loaded in the unit, simply pressing the playkey turns power ON and starts playback automatically.To stop the playback, press the 7 key.

2. Display the Clock display.

3. Display the Clock Adjustscreen.The displayed time of the day blinkswhen the clock has not been adjusted.

4. Adjust the time.

5. Set the time.After setting the correct time of the day, press the SET key.

To display the time Press the CLOCK/LIGHT key. The LCD display showsthe time for abut 5 seconds then returns to the previ-ous display.

÷ In other areas than the UK, Europe andAustralia, the clock shows the time ofthe day in the 12-hour system.

÷ The previous display will reappear if nooperation is performed for about 5seconds.

15

Preparation section

16

Basi

c se

ctio

n

11

22

33

11

2233

STANDBY/TIMER

11

CD6

TUNER/BAND MUTE

TAPE™£

22

VOLUME

33

1. Switch power ON.

If a CD or cassette has been loaded in the unit, simply pressing theplay key (6) turns power ON and starts playback automatically.

2. Select the desired source.÷ If CD or TAPE is selected and a disc or tape has already been loaded

in the main unit, its playback starts now.

3. Volume adjustment.The volume

decreases

The volume

increases

Let's put out some sound

Basic use method

17

Basic section

PHONES

INPUT

ENTER

¢4 –P.CALL–

VIDEO2CD

TUNERTAPE

FUNCTION

MUTE

CURSOR

SET

Muting the sound temporarily

÷ Press again to resume the original volume.÷ This is also cancelled when the volume is changed.

MUTE

Listening through headphonesInsert the headphone plug into the “PHONES”

jack.

÷ Headphones with a stereo mini plug can be connected.÷ The sounds from all speakers are cut off.

Standby mode

While the standby indicator of the unit is lit in red oramber, a small amount of current is flowing into theunit’s internal circuitry to back up the memory. Thiscondition is referred to as the standby mode of the unit.While the unit is in the standby mode, it can be turnedON from the remote control unit.

One-touch operationWith this feature, when the play key for the CD or TAPEinput or the BAND key for the TUNER input is pressed,the power of the unit is switched ON automatically.÷ When the CD or TAPE input selected while a disc or

tape has already been loaded, its playback also startsautomatically.

STANDBY/TIMER indicatorWhen power is STANDBY : Lights in red.

When power is ON : Lights in green.

During timer standby : Lights in amber.

When timer standby is initiated without set-

ting the current time of the day :

Blinks in green.

When the protection circuitry is activated :

Blinks in red. (In this case, unplug the

power cord and ensure that the

speaker cords are not short-circuited.)

When using the remote control unit, each press ofthe INPUT key switches the input as shown below.

1 Press INPUT key

1 VIDEO12 VIDEO23 CD4 TUNER5 TAPE

2 Press 6(BAND) key

Adjusting the left and right volume balance

1 Display the "Function" menu.

2 Select "Balance".

3 Adjusting the left and rightvolume balance

4 Set the adjusted balance.

The rightvolume isdecreased.

The leftvolume isdecreased.


When the display of the remote controlunit shows nothing, information can bedisplayed by pressing the HOME key.

CURSOR

SET

18

Basi

c se

ctio

n

TUNER/BAND

11

¢4 –P.CALL–

11

22

TUNER/BAND

22

33

33

1122

1. Select the TUNER input.

2. Select the broadcast band.Each press changes the band.

1FM

2AMor

1FM

2MW

3LW

3. Select a station.It is recommended to preset radio stations in advance.

Every time the key (4 or ¢) is pressed, the preset stations are

switched over as follows.

Press ¢ for the order of 1=2=3 ... 38=39=40=1...

Press 4 for the order of 40=39=38 ... 3=2=1=40...

When the key is held depressed for more than 2 seconds... \Seek of preset stations starts and stops automatically when

a station is detected.

Main unit

Main unit

Remote control only

Receiving broadcast station


19

Basic section

INPUT

Remote control

Remote control

6BAND


Frequency display

preset numberdisplay

Switching between stereo tuning and monaural tuningUse the monaural tuning mode when the radio wave is weak and noisy.

1 With the TUNER inputselected, press the SETkey to display the Tunermenu.

SET

2 Select "Stereo/Mono". 3 Select "Stereo" or "Mono"and press the SET key toset the selection.

To receive a station that has not been preset

1 Select the TUNER input andthe receiving band.

2 Press the SET key to displaythe Tuner menu.

3 Select the “Direct Tuning”Select with the CURSOR

key and press the SET key.

4 Select the receiving fre-quency.Select the frequency with one of

the P.CALL keys and press the

SET key to set the selection.

6BANDINPUT

CURSOR

SET

CURSOR

SET

SET

CURSOR

SET

¢4 –P.CALL–

SET


20

Basi

c se

ctio

n

INPUT

TVVIDEO1VIDEO2

CDTUNERTAPE

FUNCTION


A maximum of 40 stations will be preset.

When there are many stations and the intended

station has not been preset, please also use

“One-by-one presetting (manual preset)”.


2 Display the "Tuner" menu.

3 Select "Auto Preset" or"Auto Memory".


CURSOR

SET

Collective presetting of stations (auto preset) (Except for Europe and U.K.)Presetting R.D.S. stations (RDS auto memory for Europe and U.K. )

÷ The displayed information is variable depending onareas.

÷ It takes a certain period of time before presettingcompletes.

SET

CURSOR

SET

21

Basic section

Desired radio stations can be selected and

preset one by one. (Up to 40 stations can be

preset in memory.)

1 Receive a desired stationin advance.("To receive a station thathas not been preset")

(

2 With the TUNER inputselected, press the SETkey to display the Tunermenu.

3 Select "Manual Memory"with the CURSOR key andpress the SET key.

4 Select one of presetnumbers 1 to 40.

CURSOR

SET

One-by-one presetting (manual preset)

To preset another station, repeat steps 1 to

4 above.


SET

CURSOR

SET

CURSOR

SET

22

Basi

c se

ctio

n

11

22

22

0

11

CD6

T/

22

TVVIDEO1VIDEO2

CDTUNERTAPE

FUNCTION

1. Load a disc.1Open the CD tray.

2Place a disc.

3Close the CD tray.

2. Start playback.

The label side mustbe on top.

Display when the remotecontrol unit is attached tothe main unit

Display when the remotecontrol unit is detachedfrom the main unit

Track No. being played

Displayed with a CDTEXT-compat ib ledisc. £

Elapsed play time of thetrack being played

Track No. being played

Display during playback(During stop: "Stop".During pause: "Pause")

When a CD disc has been loaded in the CD tray in

advance, simply pressing the CD 6 key on the

main unit turns power ON and starts playback

automatically.Playback of CD

Skipping

tracksStartplayback/to pauseplayback

To stop playback

INPUT

Startplayback/to pauseplayback


TVVIDEO1VIDEO2

CDTUNERTAPE

FUNCTION

STOP

23

Basic section

6BAND

CD6

TUNER/BAND

STOP

0

Skipping tracks

To skip backward To skip forward

÷ The track in the direction of the key pressed isskipped, and the selected track will be played from thebeginning.

÷ When the 4 key is pressed once during playback, thetrack being played will be played from the beginning.

When a key is held depressed:÷ The track is fast forwarded or reversed.÷ Normal playback resumes from the position

where the key is released.

÷ Each press pauses and plays the CD alternately.

To pause playback

To stop playback

To eject the disc

÷ The CD tray opens.

1 Press the INPUT key to select the CD input.


2 Press 6(BAND) key

Remote control operation... In regard to CD-TEXTWhen discs conforming to CD-TEXT are played with

this unit, the text information recorded on the CD

(disc name or titles) is displayed automatically.

During stop: The disc title is displayed.During playback: The title of the track being

played is displayed.

CD-TEXT displayWhen the remote control unit is attached to the

main unit: Characters are scrolled (moved) from

the right to the left.

When the remote control unit is detached from the

main unit: Only the first 10 characters are displayed.


¢4 –P.CALL–

INPUT

24

Basi

c se

ctio

n

PUSH OPEN

TAPE™£

22

22

STOP

A

11

22

11

DIRECTION

Playback of tapeIf you load a tape in the cassette deck in advance

while the power is off. pressing the TAPE key

turns power on automatically and starts the tape

playback.

CURSOR

INPUTFast forwarding/rewinding orskipping tape

To stop playback

1. Load a cassette tape.1 Open the cassette holder.

2 Insert a tape and close the

cassette holder

2. Start playback.During playback, the tape running direction changes each time the

key is pressed.

÷ Be sure to remove tape slack.÷ Be sure to close the cassette holder completely.÷ The normal (TYPE I), High (TYPE II) or Metal (TYPE

IV) tape types are detected and set automatically.

Note on the tape transport direction

The direction in which tape advances when playback orrecording is started automatically by the one-touch opera-tion feature, etc. is indicated by an indicator. The indicatedtape direction it that used when the tape was stoppedlast. (To switch the direction, press the DIRECTION keyon the remote control unit.)

To stop playback

÷ Do not take out the cassette tapeuntil the tape transport has stoppedcompletely.

The tape counter is set to “0000” when a cassette tape is loaded.

By writing down the counter reading in case you want to interrupt

recording (playback) in the middle of the tape, the memo will be helpful

as a reference for locating the same position when continuing the

recording (playback) the next time. The tape counter figure decrements

during recording or playback of the back side (while the ¤ tape

transport indicator is lit).

To set the tape counter to “0000”, open the cassette holder once.

Then the counter will be reset.

A tip for use of the tape counter


25

Basic section

CURSOR

SET

6BAND

TVVIDEO1VIDEO2

CDTUNERTAPE

FUNCTION

Fast forwarding/rewinding or skipping tapeBy leaving non-recorded blanks of 4 seconds or

more between each piece of music, desired piece of

music can be selected by skipping others (up to 16

in each of the backward and forward directions).

To rewind tape or skip

music in direction |To fast forward tape or

skip music in direction \

When the key is pressed during stop÷ Fast forwarding or rewinding starts.÷ Press the stop key (7) to stop fast forwarding or rewinding.

When the key is pressed during play÷ Skipping of music starts.

Caution for cassette tape ejection÷ Do not attempt to eject the cassette tape until the

tape has been stopped completely by pressing the

stop (7) key. Opening the cassette holder while the

mechanism is running may lead to malfunction.

Should it become impossible to close the cassette

holder, turn power off then on again.

1 Press the INPUT key to select the TAPE input.

1 VIDEO12 VIDEO23 CD4 TUNER5 TAPE2 Press 6(BAND) key.

Remote control operation...

Displayed when Dolby NR is selectedReverse mode indicator

tape transportdirection indicator

When the remote control unit is attachedto the main unit: Tape counterWhen it is detached from the main unit:"Stop" for stop, "Play" for playback.

Selecting Dolby NRUsing the Dolby NR in recording allows you to

reduce tape hiss noise. Be sure to set "Dolby NR"

on when playing back a tape recorded with Dolby

NR.

1 Select "TAPE" with the CURSOR key.

2 Display the "TAPE" menu.

3 Select the "Dolby NR" setting mode.

4 Select "On" or "Off" and press the SET

key.

Selecting the reverse modeThe reverse mode determines the mode of auto-matic reversal of tape at the end of each side.


2 Display the "TAPE" menu.

3 Select the "Direction" setting mode.

4 Select one of the following reverse

modes and press the SET key.

1 “ ”: Playback stops after having

played one side of tape.

2 “ ”: Playback stops after having

played both sides of tape in a

deck.

3 “ ”: Endless playback of both

sides of tape.


¢4 –P.CALL–

INPUT

CURSOR

SET

SET

CURSOR

SET

CURSOR

SET

CURSOR

SET

SET

CURSOR

SET

26

Basi

c se

ctio

n

INPUT

¶REC

CURSOR

DIRECTION

SET

PUSH OPEN

DIRECTION

Recording on TAPE Note that this cassette deck cannot record onto

Metal tapes.NoteNoteNote

Let's recording

1. Load a cassette tape.1 Open the cassette holder.

2 Insert a tape and close the

cassette holder

÷ Be sure to remove tape slack.÷ Be sure to close the cassette holder completely.÷ The normal (TYPE I) or High (TYPE II) tape types are detected and set auto-

matically.÷ Use a cassette tape with which the protect tab for accidental erasure pre-

vention is not broken. T

TUNER (Broadcasts)

VIDEO1

VIDEO2

2. Select the source to be recorded.

To record sound from a CD, use the dedicatedrecording function by referring to "CD synchro-nized recording" (¶) or "Convenient record-ing methods" (fl).The present procedure described the mostgeneral recording method

3. Select the tape transport direction.

÷ When recording is started, the tape is transported in the direction selected in thisstep.

÷ Wind the tape to the position where recording is to be started.

To reverse the tape transport direction


2 Press the SET key.

3 Press the DIRECTION key to switch the

tape transport direction.

1 2

3

INPUT

CURSOR

SET

27

Basic section

REC

REC

7

TVVIDEO1VIDEO2

CDTUNERTAPE

FUNCTION

Pause the recording (A.R.M.)

÷ Press the ¶REC key during recording. It stops afterleaving a non-recorded blank of 4 seconds. (Press thekey again to resume recording.)

Stop the recording

CD synchronized recordingWhen recording a CD, the playback of the sourceand recording of the cassette deck can be synchro-nized by putting the cassette deck in record-pausemode. (Sync recording)

1Put the CD recorder in pause mode.2Select the music to be recorded by using the

skip key (4 or ¢). (The tape pauses at thebeginning of the selected music.)

3Put the cassette deck in record-pause mode.4Start playback of the CD. (Sync recording

starts.)

÷ Press the stop key (7) of the CD player to stoprecording.

4. Set the recording condition.1Perform steps 2 to 4 of "Selecting the reverse mode" on page 25.

2Perform steps 2 to 4 of "Selecting Dolby NR" on page 25.

5. Start recording.

Displayed when Dolby NR is selectedReverse mode indicator

tape transportdirection indicator When the remote control unit is

attached to the main unit:Tape counter

When it is detached from the mainunit:"Stop" for stop,

"Play" for playback,

"Rec Pause" for record pause,

"A.R.M." during A.R.M. op-

eration.

Recording indicator

÷ Recording stops automatically when the tape side (s)to be recorded have been fully recorded.

Let's recording

Check that "Tape" is being displayed,then press the REC button.

28

Appl

icat

ion

sect

ion

RDS is a system which transmits useful informa-

tion (digital data) for FM broadcasts together with

the broadcast signal. Tuners and receivers de-

signed for RDS reception can extract the informa-

tion from the broadcast signal for use with vari-

ous functions such as automatic display of the

station name.

R.D.S. (Radio Data System) (for Europe and U.K.)

This unit is equipped with the following functions utilizing RDS data :

PTY (Program Type Identification) Search :The tuner automatically searches for a station which iscurrently broadcasting a specified program type (genre).

PS (Program Service Name) Display :When an RDS broadcast is received, the station name isautomatically displayed.

EON (Enhanced Other Network) :When the information to be received is set in advanceand any RDS station in the same network starts broad-casting of such information, the reception automaticallywill be switched to that station.

TVVIDEO1VIDEO2

CDTUNERTAPE

FUNCTION

RDS, EON, TP indication

Program numberindication

PS or PTYdata indication

Frequency indication

Before using RDSFor reception of RDS stations, the auto presetting function must be used to preset the stations.

With the auto presetting function, RDS stations are preset with priority.

29

Application section

CURSOR

SET

INPUT

SET



3 Select "PTY ".

4 Select the desired PTY.

CURSOR

INPUT

SET

By specifying the type of program (genre) you

want to listen to, the tuner automatically searches

for a station which is currently broadcasting a

program of the specified type.

Searching for a desired program type (PTY search)

"" shows the currently

selected PTY display.

÷ When an RDS broadcast is received, the programtype is shown on the display. If no PTY data is avail-able, or if the station is not an RDS station, “NONE”is displayed.

R.D.S. (Radio Data System)

TVVIDEO1VIDEO2

CDTUNERTAPE

FUNCTION


CURSOR

SET

Preset the RDS stations before setting the PTY

30

Appl

icat

ion

sect

ion

TVVIDEO1VIDEO2

CDTUNERTAPE

FUNCTION


CURSOR

INPUT

SET

To be able to listen to the desired information at any time (EON)

By using the EON function, which manages the information of other stations, listening to desired

information like traffic information or news etc. can be reserved even when it is not being transmitted at

the present. When listening to a station with the “EON” display lit and another station of the same

network starts to broadcast an information program for which a reservation has been made, then that

station will be selected automatically. When the desired information program ends, return is made to the

original program.



3 Select "EON ".

4 Select the desired EONmode.

"" shows the currently

selected EON mode display.

Off ........................... EON cancelled

TA ........................... Traffic Announcement

NEWS ..................... News

TA & NEWS ........... Traffic Announcement

and News

Select the desired information.1


CURSOR

SET

INPUT

SET

CURSOR

SET

31

Application section

Receive an RDS station.2

¢4 –P.CALL–

Select a station where “RDS” and “EON” are lit. “RDS” and “EON” are Lit

Wait for the desired information.3

CD or TAPE playback may also be started.

As long as the unit is ON, the unit is always ready

for the reception.

÷ When one of the stations of the network of the stationreceived in 2 starts broadcasting the program contentsselected in 1, that station will be received automatically.At this time, Tape playback will stop and CD playback willpause. However, external equipment (VIDEO1/VIDEO2)will remain as it is.

In case of waiting for information with anRDS station without EON functionWhen there is no “EON” display with the op-

erations of steps 2 and 3 and the desired infor-

mation is selected in advance, waiting for the

desired information will be done only with the

presently received RDS station.

In regard to TP (Traffic Program) indicatorWhen the “TP” indicator is lit, this indicates that

the station or another station in the same net-

work is broadcasting traffic information. Even

without an EON reservation, traffic information

can be heard from the station when “TP” indi-

cator is lit for the presently received station.


÷ When the unit is OFF or during recording, the EONfunction does not operate.

÷ When the transmission of the selected program con-tents ends in case of automatic reception with the EONfunction, return will be made to the status directly beforeoperation of the EON function. When CD or TAPE play-back has been interrupted, it will be continued from thepoint of interruption.

Each press of the stop (7) key switches the PS

and PTY display alternately.

32

Appl

icat

ion

sect

ion

ENTER

CURSOR

INPUT

ENTER

SET

6

TVVIDEO1VIDEO2

CDTUNERTAPE

FUNCTION

Playback of CD

Listening in the desired sequence (program playback)Use the following procedure to program desired

tracks in a desired order. (up to 32 tracks)

Program desired tracks. (In stop mode only)11 Select the CD input.

2 Display the "CD" menu.

3 Select the message to bedisplayed, "Program On"or "Program Off".

4 Select the "Set".

5 Select a track numberand press the SET key.

6 To program other tracks,repeat step 5 for eachtrack.

7 Press the ENTER key toquit programming.

÷ When "Clear" is selected, the program being dis-played will be cleared.

÷ Up to 32 tracks can be programmed. When "Pro-gram Full" is displayed, no more track can be pro-grammed.

÷ If you make a mistake in the middle, press theHOME key to return to the basic screen.

INPUT

SET

CURSOR

SET

CURSOR

SET

CURSOR

SET

33

Application section

Play the programmed tracks.

6BAND

¢4 –P.CALL–

1 Select the CD input.


3 Select the message to bedisplayed, "Program On".

4 Select the "Check".

5 Display a program numberand check the track pro-grammed under it.

6 Press the ENTER key toquit program checking.

2÷ Pressing the 4 or ¢ key during playback skips

to one of the tracks programmed before or afterthe current track.

÷ Pressing the 4 key once during playback returnsto the beginning of the current track.

Checking the program (In stop mode only)Use the following procedure to check the pro-

grammed tracks.

Clearing the program (In stop mode only)Use the following procedure to clear all the pro-

grammed tracks from the program.



3 Select the message to bedisplayed, "Program On".

4 Select the "Off".

Playback of CD

ENTER

INPUT

SET

CURSOR

SET

CURSOR

SET

INPUT

SET

CURSOR

SET

CURSOR

SET

34

Appl

icat

ion

sect

ion

CURSOR

INPUT

SET

6

6BAND

TVVIDEO1VIDEO2

CDTUNERTAPE

FUNCTION

Repeated playbackYou can repeatedly listen to a favorite track or

disc.

Program repeat playback÷ By programming only the desired tracks, it is

possible to perform the repeat playback of

only the programmed tracks later.

÷ To repeat playing a single track, program that

track only and start its repeat playback.



3 Select the message to bedisplayed, "Repeat Off" or"Repeat On".

4 Select "On".

5 Start playback ÷ The entire disc will be played repeatedly.÷ When both repeat playback and random playback

(fi) are used simultaneously, all tracks in the discwill be played in a random order and this randomplayback will be repeated.

To cancel repeat playbackSelect "Off" in step 4 to cancel repeat playback.

To stop operation in the middlePress the HOME key to abort and cancel the

operation and return to the basic screen.

Playback of CD

INPUT

SET

CURSOR

SET

CURSOR

SET

35

Application section

CURSOR

INPUT

SET

6

TVVIDEO1VIDEO2

CDTUNERTAPE

FUNCTION



3 Select the message to bedisplayed, "Random Off"or "Random On".

4 Select "On".



Listening to an unexpected title sequence (random playback)As the titles each time are selected randomly, the

music can be enjoyed without getting tired of it.

÷ It is not possible to perform random playback

of programmed tracks.

Random repeat playback÷ When repeat playback is set before starting

random playback, the random playback of the

disc will be repeated.

Cancel the program mode. ¤

÷ The tracks in the entire disc will be played in a ran-dom order, after which playback will stop.

To cancel random playbackSelect "Off" in step 4 to cancel random play-

back.

Playback of CD

INPUT

SET

CURSOR

SET

CURSOR

SET

36

Appl

icat

ion

sect

ion

\

\

\

Convenient Recording Methods

Selection of the Recording TypeThis unit provides the following recording fea-

tures in addition to normal recording. Select the

appropriate method according to the purpose of

recording.

Note that this cassette deck cannot record

onto Metal tapes.NoteNoteNote

Recording all tracks in a CD onto tapeCD direct recording ‡

CD direct recording Records all tracks in a CD onto tape.

Recording a single track in CD onto tapeCD one-track recording °

CD one-track recording

Records the CD track being played onto a

tape.

(This is convenient when you play a CD for

the first time but want to select and record

only the desired tracks.)

Recording desired CD tracks in a desired order onto tapeCD program recording ·

CD program recording

Records the programmed CD tracks in the

programmed order.

(This is convenient when you want to

program and record desired tracks in a CD

in a desired order.)

With recording onto tape, the track will be interrupted for the part of the guide tape at the tape reversal,where recording is not possible. Please use single-side recording if this is to be avoided.NoteNote

37

Application section

CURSOR

ENTER

SET


2 Select the message to bedisplayed, "CD→TapeRec".

3 Select the "Direct Rec".

4 Start recording

Recording an entire CD onto tape (CD direct recording)÷ This function is canceled when the program

mode is activated.

÷ This function is available only when the CD

player is in stop mode.


Total number of tracks in CD,total play time

CURSOR

SET

CURSOR

SET

CURSOR

SET

ENTER

Preparation÷ Perform step 3 ( "Select the tape transport direc-

tion") on page 26.÷ Perform steps 2 to 4 of "Selecting the reverse

mode" on page 25.



38

Appl

icat

ion

sect

ion

CURSOR

ENTER

SET



3 Select the "One TrackRec".

4 Start recording

Recording every desired track in CD onto tape (CD one-track recording)During playback of a CD track, only the track being

played can be selected and recorded from the

beginning.

÷ CD random playback cannot be recorded.


CD track No. being played, elapsedplay time of the track being played

CURSOR

SET

CURSOR

SET

CURSOR

SET

ENTER





mode" on page 25.

39

Application section

CURSOR

ENTER

SET



3 Select the "Program Rec".

4 Program CD tracks.

5 Start recording

Recording desired CD tracks in a desired order onto tape (CD program recording)The desired tracks in a CD can be programmed in

a desired order and recorded.


Number of programmed CD tracks,total play time of the program

÷ This function is available only when the CD

player is in stop mode.

Follow 5 to 7 in step 1 on

page 32.

CURSOR

SET

CURSOR

SET

CURSOR

SET

ENTER





mode" on page 25.

40

Appl

icat

ion

sect

ion

¢4 –P.CALL–

CURSOR

ENTER

SET

4, ¢

Tone control and sound field effect adjustment

Use the following procedure to adjust the levels of

the Video1 and Video2 inputs.

Adjusting the external input level


2 Select the message to bedisplayed, "Input Level".

3 Select the "Video1" or"Video2" .

4 Adjust the input level ofthe selected input.

5 Press the ENTER key

The adjustment range is be-

tween +3 and -4.

CURSOR

Adjusting the subwoofer output level (NV-600 only)


2 Select the "S.W. Level".

3 Adjust the level of thesubwoofer output.



tween 1 and 5.

CURSOR

SET

CURSOR

SET

ENTER

CURSOR

SET

CURSOR

SET

¢4 –P.CALL–

ENTER

41

Application section

¢4 –P.CALL–

CURSOR

ENTER

SET

4, ¢

CURSOR

Bass Boost and tone controlThe Bass Boost function allows you to enhance

or compensate for the low frequencies and the

tone control function is used for fine adjust-

ments of the bass (low frequencies) and treble

(high frequencies).

Selecting the bass boost(NV-500 only )


2 Select the "Listen Mode".

3 Select the message to bedisplayed, "Bass BoostOff" or "Bass Boost On".

4 Select the message to bedisplayed, "On" or "Off",and press the SET key.

Tone adjustmentThe lowest and highest frequency bands can beadjusted independently.


2 Select the "Tone Control".

3 Select the message to bedisplayed, "Bass" or"Treble".

4 Adjust the level of theselected tone.



tween +4 and -4.


÷ The sound field effects of Bass Boost and tone

control cannot be used simultaneously.

The tone control setting is

switched off.

The tone control setting is

recalled whenever the Bass

Boost setting is switched off.

The bass boost setting is

switched off.

CURSOR

SET

CURSOR

SET

CURSOR

SET

CURSOR

SET

CURSOR

SET

CURSOR

SET

ENTER

42

Appl

icat

ion

sect

ion

CURSOR

ENTER

SET

4, ¢

Dolby Virtual setting


The Dolby Virtual function is designed to provide

a simulated surround effect from two speakers

on the left and right. This is a convenient function

for playing a movie, etc.

÷ The DSP mode is canceled when Dolby Vir-

tual is set.



3 Select the message to bedisplayed, "Virtual On" or"Virtual Off".

4 Select "On" or "Off".

Setting ON or OFF Select level



3 Select the message to bedisplayed, "Virtual On".

4 Select the "Effect Level ".

5 Select the “Level 1”,“Level 2” or “Level 3”


CURSOR

SET

CURSOR

SET

CURSOR

SET

CURSOR

SET

CURSOR

SET

CURSOR

SET

CURSOR

SET

CURSOR

SET

ENTER

¢4 –P.CALL–

43

Application section

CURSOR

ENTER

SET

4, ¢


The DSP (Digital Surround Processor) controls the

tone of a signal in the digital form and makes

sound processing without quality degradation

possible. The DSP built into this unit provides

appropriate tone patterns (equalizing patterns)

for major musical categories.

DSP mode setting



3 Select the message to bedisplayed, "DSP On” or“DSP Off”.

4 Select the desired DSPpattern.

÷ The Dolby Virtual function is canceled when

the DSP mode is set.

“Off”

“Stadium”

“Arena”

“Live house”

CURSOR

SET

CURSOR

SET

CURSOR

SET

CURSOR

SET

This display shows the example with the NV-500.

44

Appl

icat

ion

sect

ion

CURSOR

ENTER

SET

4, ¢

¢4 –P.CALL–

SET

Timer operation Adjust the clock before setting the timer.

O.T.T. :Starts playback of the selected input source when the set time comes and turns power off in an hour. This

program is executed only once every time after it is set.

Timer playback, timer recording:Plays the selected input source (or records tuner broadcasting or external input source) in the set time zone.

SLEEP timer:Turns power off automatically after the set period of time.

When more than one timer setting overlapsWith this unit, the O.T.T. on time, the timer play-back on time/off time and the timer recording ontime/off time can be set independently. If morethan one timer setting overlaps in a certain pe-riod, the timer functions are activated in the fol-lowing priority order:

1 O.T.T.

2 Timer playback

3 Timer recording

Setting the O.T.T.


2 Select the message to bedisplayed, "O.T.T. Off" or“O.T.T. On”.

3 Select the message to bedisplayed, "On”.

4 Set the timer start time.

5 After setting the starttime, press the ENTERkey.

6 After completing the set-ting, set the power OFF.

To return time To advance time

÷ Select "Off" when you want to cancel the O.T.T. timer.

÷ The time is variable in 5-minute steps.

÷ When the timer has been set and power set to OFF,the STANDBY/TIMER indicator lights up in amber.

CURSOR

SET

CURSOR

SET

CURSOR

SET

ENTER

÷ In other areas than the UK, Europe and Australia,the clock shows the time of the day in the 12-hoursystem.

When the time set by the timer comes, the last sourcewhich was selected before the power was switched offwill be played back.

45

Application section

CURSOR

ENTER

SET

4, ¢

Setting the timer playbackTimer playback includes normal timer playback

and AI (Artificial Intelligence) timer playback.

Normal timer playback:Starts playback of the selected source at the set

on time and turns power OFF at the set off time.

AI timer playback:Increases the playback volume gradually after

the start of timer playback.


2 Select the message to bedisplayed, "Timer PlayOff" or “Timer Play On”.


4 Set the on time.

5 Set the off time.

6 Select the input to beplayed by timer.

÷ Select "Off" when you want to cancel the timer.

÷ It is not permitted to set the same time of day asthe on time and off time.

To return to the previous operation step in the middle,select "Back" with the CURSOR key and press the SET

key. Select "Next" to advance to the next step.

¢4 –P.CALL–

SET

CURSOR

SET

CURSOR

SET

CURSOR

SET

¢4 –P.CALL–

SET

¢4 –P.CALL–

SET

Timer operation

Continued to next page

46

Appl

icat

ion

sect

ion

¢4 –P.CALL–

SET

¢4 –P.CALL–

SET

¢4 –P.CALL–

SET

7 Select a preset radio station.(This step is required only

when the tuner input is

selected in the above.)

8 Select the message to bedisplayed, "AI-Play" or“Normal-Play”.

9 Press the ENTER key tocomplete the setting.


Sleep Timer (Sleep)


2 Select the message to bedisplayed, "Sleep On” or"Sleep OFF”.

3 Set the time period untilthe power is to be turnedOFF.

÷ The time period can be set in 10-minute steps from"Off" up to "90" minutes.

÷ Selecting "Off" cancels the sleep timer setting.

÷ The back light of the remote control unit turns offwhile the sleep timer is active.

÷ The power will turn off when the set time periodhas elapsed.

÷ When the timer has been set and power set to OFF,the STANDBY/TIMER indicator lights up in amber.

ENTER

CURSOR

SET

CURSOR

SET

Timer operation

47

Application section

CURSOR

ENTER

SET

4, ¢

Timer recording


2 Select the message to bedisplayed, "Timer Rec Off"or “Timer Rec On”.


4 Perform the setting op-eration in steps 4 to 5under "Setting the timerplayback".

5 Select the input source tobe recorded.

6 Select a preset radio station.

7 Press the ENTER key.


÷ Select "Off" when you want to cancel the timer.

÷ "Tuner", "Video1" or "Video2" can be selected.

To return to the previous operation step in the middle,select "Back" with the CURSOR key and press the SET

key. Select "Next" to advance to the next step.

Timer recording is used to record a source onto a

tape.

The TUNER or the component connected to the

Video1 or Video 2 input can be selected as the

source.

(This step is required only when the tuner

input is selected in the above.)

¢4 –P.CALL–

SET

¢4 –P.CALL–

SET

CURSOR

SET

CURSOR

SET

CURSOR

SET

Timer operation

÷ Audio is not output during timer recording.

48

Appl

icat

ion

sect

ion

CURSOR

SET

CURSOR

SET

TVVIDEO1VIDEO2

CDTUNERTAPE

FUNCTION

Checking the time information display of CD

The remote control unit can display the time

information of CD such as the playing time and

total time.

The time information can be checked while the

CD is playing or stopped.


2 Select the informationitem to be displayed.

The items as shown below can

be selected.

CD Single Time display

During stop in normal mode:

Playing time of the first track.During playback in normal mode:

Playing time of the track being played.During stop in program mode:

Playing time of the first programmedtrack.

During playback in program mode:

Playing time of the track being played.

In normal mode:

Total playing time of the disc.In program mode:

Total playing time of the programmedtracks.

CD Total Time display

CURSOR

SET

49

Application section

CURSOR

ENTER

SET

4, ¢

¢4 –P.CALL–

SET

ENTER

Adjusting the display contrastUse the following procedure to adjust the density of the

display on the remote control unit.


2 Select the message to bedisplayed, "Contrast".

3 Adjust the contrast.


CURSOR

SET

CURSOR

SET

50

Appl

icat

ion

sect

ion

CURSOR

ENTER

SET

CURSOR

SET

SET

ENTER


2 Select the message to bedisplayed, "TV".

3 Select the manufacturer.

4 Select the type of theremote control codes.

5 Check the remote controloperations.

6 If the operations are nor-mal, press the ENTER keyto set it.

Registering the TV to be used

Remote control of external components

Registering the controlled components in the remote control unitThe remote control unit can also be used to control the

major functions of externally connected components

such as a TV, VCR and DVD player.

To make the control possible, it is required to select the

manufacturer and type (VCR, DVD, etc.) of each com-

ponent and register it in the memory of the remote

control unit.

Note that, with components from certain manufactur-

ers or of certain types, remote control may not be

available or the controllable functions may be limited.

÷ Press the SET key and ensure that the componentis turned ON.

÷ If normal operation cannot be performed, place thecursor on "Back" and re-select the code type. Besure to check the results later.

The manufacturer list is displayed.

CURSOR

SET

CURSOR

SET

CURSOR

SET

51

Application section

Registering the component connected to therear-panel Video1 or Video2 input


2 Select the message to bedisplayed, "Video1" or"Video2".

3 Select the type of the com-ponent (VCR, DVD, etc).

4 Select the manufacturer.

5 Select the type of theremote control codes.

6 Check the remote controloperations.

7 If the operations are nor-mal, press the ENTER keyto set it.

÷ Press the SET key and ensure that the componentis turned ON.

÷ If normal operation cannot be performed, place thecursor on "Back" and re-select the code type. Besure to check the results later.

÷ The cable tuner and DSS operations are not avail-able in other areas than the U.S.A. and Canada.

÷ The displayed information is variable depending onareas.

The manufacturer list is displayed.

CURSOR

SET

SET

ENTER

CURSOR

SET

CURSOR

SET

CURSOR

SET

CURSOR

SET


52

Appl

icat

ion

sect

ion

TVVIDEO1VIDEO2

CDTUNERTAPE

FUNCTION

TVVIDEO1VIDEO2

CDTUNERTAPE

FUNCTION

TVVIDEO1VIDEO2

CDTUNERTAPE

FUNCTION

VOLUME

CLOCK MUTE

CONFIRM/DEMO

HOME

INPUT DIRECTION

SET ENTER

¶REC

– P.CALL –

BACK LIGHT

CURSOR

6

7

¢ 4

Remote control of external componentsBy registering the externally connected components such as a TV, VCR and DVD player in the remote

control unit, it can be used to control the major functions of the external components.

Select the input corresponding to the com-ponent to be remote controlled.

The display show the function names and/or sym-

bols of the 7 available remote control keys. The

correspondence between the displayed keys and

panel keys is as shown below.

If the remote control keys are provided in more

than one display page, each page can be switched

every time the SET key is pressed.


CURSOR

SET

53

Application section

TV control screenThis screen consists of a single page.

VCR control screenThis consists of 2 pages.

Each press of the SET key switches the pages alter-

nately.

DVD control screenThis consists of 3 pages.

Each press of the SET key switches the pages alternately.

Cable Tuner control screen (for U.S.A.& Canada)This screen consists of a single page.

DSS control screen (for U.S.A. & Canada)This consists of 2 pages.

Each press of the SET key switches the pages alter-

nately.

Symbol on the Display Functionremote control

6 BAND Vol 5 Volume Up

7 Vol ∞ Volume Down

¢ Ch 5 Channel Up

4 Ch ∞ Channel Down

ENTER PWR Power

DIRECTION MUTE Muting

¶ REC INPUT Input selection

Symbol on the Display Function Display Functionremote control

6 BAND ‰ Play ‰ Play

7 7 Stop 7 Stop

¢ ¡ Fast forward Ch5 Channel Up

4 1 Fast reverse Ch∞ Channel Down

ENTER PWR Power PWR Power

DIRECTION PAUSE Pause AUDIO* Audio switching

¶ REC REC Record INPUT Input selection

Symbol on the Display Functionremote control

6 BAND Vol 5 Volume up

7 Vol ∞ Volume down

¢ Ch 5 Channel up

4 Ch ∞ Channel down

ENTER PWR Power

DIRECTION – –

¶ REC – –

Symbol on the Display Function Display Functionremote control

6 BAND – – Cursor

7 – – Cursor

¢ Ch5 Channel up ‰ Cursor

4 Ch∞ Channel down Cursor

ENTER PWR Power ENTER Enter

DIRECTION INFO Informatiom MENU Menu

¶ REC INPUT Input selection GUIDE Guide

‰‰

‰

‰

Symbol on the Display Function Display Function Display Functionremote control

6 BAND ‰ Play Cursor Cursor

7 7 Stop Cursor Cursor

¢ ¢ Forward skip ‰ Cursor ‰ Cursor

4 4 Reverse skip Cursor Cursor

ENTER PWR Power ENTER Enter ENTER Enter

DIRECTION PAUSE Pause OSD OSD MENU Menu

¶ REC – – RTN Return RTN Return

*Note: This function is available only with other models than the Europe, UKand the U.S.A. destination models.

‰

‰


‰

‰‰

54

Know

ledg

e se

ctio

n

Cleaning the head section Cleaning the heads and peripheral componentsFor maintaining the best condition of the deck and for longer service life, alwayskeep the heads (recording / playback / erase), capstan and pinch roller clean.To clean them, perform the following:1.Open the cassette holder.2.Using a cotton swab dipped in alcohol, clean the head (recording / playback /

erase), capstan and pinch roller carefully.Demagnetizing the headWhen the recording / playback head is magnetized, the sound quality willdeteriorate. In such a case, demagnetize the head using a commercially availabledemagnetizer (head eraser).

Maintenance

There are precisely aligned parts around the heads, including the tape guides.When cleaning, pay special attention so as not to apply shock to them.NoteNoteNote

Cotton swab

Head

Capstan

Pinch roller

Tape guides

Caution on condensationCondensation (of dew) may occur inside the unit whenthere is a great difference in temperature between thisunit and the outside.This unit may not function properly if condensation oc-curs. In this case, leave the unit for a few hours with thepower left ON, and restart the operation after the con-densation has dried up.Be specially cautious against condensation in a fol-

lowing circumstance:

When this unit is carried from a place to another across alarge difference in temperature, when the humidity in theroom where this unit is installed increases, etc.

Reference

Maintenance of the SetWhen the front panel, the case, etc. becomes dirty, wipewith a soft, dry cloth. Do not use thinner, alcohol, etc., asthese can cause discoloration.

In regard to contact cleanersDo not use contact cleaners because it could cause a mal-function. Be specially careful not to use contact cleanerscontaining oil, for they may deform the plastic component.

Stored contents which are

cleared immediately when

power plug is unplugged

from power outlet

Stored contents which are

cleared in at least a day after

power plug is unplugged

from power outlet

Clock display

Amplifier section

"on/standby" status(ON or STANDBY)Last input selectionVolume control valueTone control levelsVideo1/Video2 input levelBalance settingTuner section

Receiving bandFrequencyPreset stationsAuto/mono settingProgram timer settingcontentsCassette deck unit

Transport directionDolby NRReverse mode

Memory backup function

Note related to transportation and movementBefore transporting or moving this unit, carry out the

following operations.

1Select the CD input

2Press the 0 key and take out the CD.

3Ensure that "No Disc" is displayed.

4Wait for a few seconds, then set the power

OFF.

Important Items

CD6

TUNER/BAND

0

55

Knowledge section

Safety tab (accidental erasure prevention tab)After an important recording has been finished, break thesafety tab, to prevent the recorded contents from beingerased or recorded on accidentally.

For B side

For A side

To store cassette tapesDo not store the tapes in a place which is subject todirect sunlight, or near equipment that generates heat.Keep the cassette tapes away from any magnetic field.

To re-record Apply tape only to the position wherethe tab has been removed.

When there is slack in the tapeIn such a case, insert a pencil into the reel hole and windthe reel hub to remove the slack.

N

S

1.Longer tape than 110 minutes cassette tapeSince longer tape than 110 minutes cassette tape is very thin, the tape could adhere to the pinch roller or beeasily broken. It is recommended that these tapes not be used with this unit to prevent possible damage.

2.Endless tapesDo not use an endless tape, as this could damage the mechanism of the unit.

NotesNotes

Notes on cassette tape

Label sidePlaying side

CleaningIf fingerprints or foreign matter be-come attached to the disc, lightly wipethe disc with a soft cotton cloth (orsimilar) from the center of the discoutwards in a radial manner.

StorageWhen a disc is not to be played fora long period of time, remove it fromthe player and store it in its case.

HandlingHold the discs so that you do nottouch the playing surface.

Discs which can be played with this unitCD (12 cm, 8 cm), and the audio part of CDV, CD-G, CD-EGand CD-EXTRA.Use discs that comply with the IEC standard, for examplea disc carrying

DIGITAL AUDIO

COMPACT

the marking on the label surface.

Disc handling precautions

Disc accessoriesThe disc accessories (stabilizer, protection sheet, protec-tion ring, etc.) which are marketed for improving the soundquality or protecting discs as well as the disc cleaner shouldnot be used with this system because they may causemalfunction.

Do not attach paper or tape to ei-ther the playing side or the label sideof the discs.

Sticker

Sticky paste

Never play a cracked or warped discDuring playback, the disc rotates at high speed in the player.Therefore, to avoid danger, never use a cracked or deformeddisc or a disc repaired with tape or adhesive agent.Please do not use discs which are not round because theymay cause a malfunction.

Important Items

56

Know

ledg

e se

ctio

n

Note to CATV system installerThis reminder is provided to call the CATV system installer'sattention to Article 820-40 of the NEC that provides guidelinesfor proper grounding and, in partiqular, specifies that the cableground shall be connected to the grounding system of the build-ing, as close to the point of cable entry as practical

Use of controls or adjustments or performance of pro-

cedures other than those specified herein may result

in hazardous radiation exposure.

In compliance with Federal Regulations, following are

reproductions of labels on, or inside the product re-

lating to laser product safety.

KENWOOD CORPORATION

2967-3, ISHIKAWA-CHO,

HACHIOJI-SHI,

TOKYO, JAPAN

KENWOOD CORP. CERTIFIES THIS EQUIPMENT

CONFORMS TO DHHS REGULATIONS NO. 21 CFR

1040.10, CHAPTER 1, SUBCHAPTER J.

CAUTION:

Location: Back Panel

This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmfulinterference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate thisequipment if an unauthorized change or modification is made.

NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment maycause harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, thereis no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures:– – Reorient or relocate the receiving antenna.– – Increase the separation between the equipment and receiver.– – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– – Consult the dealer or an experienced radio / TV technician for help.

FCC WARNING

Dolby noise reduction manufactured under license from DolbyLaboratories. “DOLBY” and the double-D symbol are trade-marks of Dolby Laboratories.

WARNING NOTICE:IN MOST CASES IT IS AN INFRINGEMENT OF COPY-RIGHT TO MAKE COPIES OF TAPES OR DISCS WITH-OUT THE PERMISSION OF THE COPYRIGHT OWNERS.ANYONE WISHING TO COPY COMMERCIALLY AVAIL-ABLE TAPES OR DISC SHOULD CONTACT THE ME-CHANICAL COPYRIGHT PROTECTION SOCIETY LIMITEDOR THE PERFORMING RIGHTS SOCIETY LIMITED.

As an ENERGY STAR® Partner, Kenwood Cor-

poration has determined that this products meets

the ENERGY STAR® guidelines for energy

efficiency.This product can save energy. Saving energy reduces airpollution and lowers utility bills.

57

Knowledge section

In case of difficulty

Operation to resetThe microcomputer may fall into malfunction (impos-

sibility to operate, erroneous display, etc.) when the

power cord is unplugged while unit is ON or due to

an external factor. In this case, execute the following

procedure to reset the microcomputer and return it

to normal condition.

Unplug the power cord from the power outlet then,

while holding the CD Open close (0) key depressed,

plug the power cord again.

After some time, the power will be switched off

and return will be made to the initial status.

÷ Please note that resetting the microcomputer clearsthe contents stored in and it returns to condition whenit left the factory.

What seems to be a malfunction is not always so. Before calling for service, check the following table

according to the symptom of your trouble.

RemedyCauseSymptom

Amplifier section/Speakers

÷ Connect properly referring to “Systemconnection”.

÷ Adjust to an required volume.

÷ Switch MUTE OFF.÷ Unplug the headphone plug.

÷ Turn the unit OFF, remove the short-circuit and turn the unit ON again.

÷ Insert correctly.

÷ Connect properly referring to “Systemconnection”.

÷ Adjust the optimum left and right bal-ance.

Sound is not produced.

No sound from the head-phones.

Sound is not produced fromthe left or right speakers.

÷ The speaker cords are disconnected.

÷ The volume control is set to the mini-mum position.

÷ The MUTE key is switched ON.÷ The headphone plug is inserted into the

jack.÷ The speaker cords are short-circuited.

÷ Imperfect insertion.

÷ The speaker cords are disconnected.

÷ The BALANCE is set completely to theleft or right channel.

RemedyCauseSymptom

÷ Adjust the present time again.÷ Adjust the present time again.

÷ Adjust the present time referring to“Clock adjustment”.

÷ Set the timer ON time and OFF time.

÷ Press the ON STANDBY key to set upthe execution.

÷ Connect antennas.÷ Select a band.

÷ Tune to the frequency of the desiredstation.

÷ Install the outdoor antenna in an apartposition from the road.

÷ Switch the suspected electric applianceOFF.

÷ Install the TV or the system at an in-creased distance between them.

÷ Preset stations with tunable frequen-cies.

÷ Preset stations again.

The clock display blinkswithout changing the fig-ures.

Timer operation is not pos-sible.

Radio stations cannot bereceived.

Noise interferes.

A station has been preset butit cannot be received bypressing the P.CALL key.

÷ There was a power failure.÷ The power cord was unplugged from the

outlet.

÷ The present time has not been adjustedor there was a power failure.

÷ The timer ON time and OFF time havenot been set.

÷ The timer execution was not set up.

÷ The antennas have not been connected.÷ A proper broadcasting band has not been

selected.÷ The frequency of the station to be re-

ceived is not tuned.

÷ Car ignition noise.

÷ Influence of an electric appliance.

÷ A TV set is installed near the system.

÷ The frequency of the preset station isnot tunable.

÷ The preset memory has been clearedbecause the power cord has been un-plugged for a long period.

$

$

t

7*

)

8

&

&

8

&

Tuner section

58

Know

ledg

e se

ctio

n

In case of difficulty

RemedyCauseSymptom

CD player section

÷ Place the disc properly, with the labelside facing upward.

÷ Place the disc properly.÷ Clean the disc referring to “Disc han-

dling precautions”.÷ Try another disc.÷ Refer to “Caution on condensation” and

remove the condensation by evaporation.

÷ Place a disc in the CD player.÷ Press the 6 key.÷ Clean the disc referring to “Disc han-

dling precautions”.÷ Try another disc.

÷ Clean the disc referring to “Disc han-dling precautions”.

÷ Try another disc.÷ Install the unit in a place not subject to

vibrations.

÷ This is not a malfunction.

A CD is placed in the playerbut it cannot be played.

Sound is not produced.

Sound skips.

“Text Full” is displayed

÷ The disc is placed upside down.

÷ The disc position is displaced.÷ The disc is extremely dirty.

÷ The disc is scratched.÷ Dew is condensed on the optics lens.

÷ The disc has not been placed.÷ The player is not put to the play mode.÷ The disc is extremely dirty.

÷ The disc is scratched.

÷ The disc is dirty.

÷ The disc is scratched.÷ The player is subject to vibration.

÷ Too much text data has been stored.

T

R

T

T

Remote control unitSymptom Cause Remedy

Remote control operation isnot possible.

The “Low Battery” alarm isdisplayed.

÷ Batteries are exhausted.÷ The remote control is too far away from

the system, the controlling angle is devi-ated or there is an obstacle in between.

÷ The component to be played is not loadedwith a CD or cassette tape.

÷ Batteries are exhausted.

÷ Replace with new batteries.÷ Operate the unit inside the remote con-

trollable range.

÷ Load a CD or cassette tape in the com-ponent to be played.

÷ Replace with new batteries.

@

@

@

59

Knowledge section

RemedyCauseSymptom

÷ Clean the head referring to “Mainte-nance”.

÷ Try another tape.

÷ Play a recorded tape.

÷ Close the holder completely.

÷ Press operation keys in more than a fewseconds after closing the cassette holder.

÷ Press operation keys after waiting formore than 4 seconds.

÷ Insert a tape.÷ Try another tape.

÷ Change the tape transport direction orreverse the tape insertion orientation.

÷ Press in stop mode.

÷ Reset the microcomputer.



÷ Adjust the Video 1, Video 2 input level.


÷ Demagnetize the head referring to “Main-tenance”.

÷ Install the system at a distance fromother electric appliances and TV.

÷ Set the "Dolby NR" to on.


÷ Wind the tape again by fast forwarding,rewinding or playing from an end to theother.

÷ Use a cassette with an unbroken record-ing protect tab or block the hole.

÷ Close the holder completely.

÷ Set the input selector to the source to berecorded.

÷ Change the tape transport direction orreverse the tape insertion orientation.

Sound cannot be producedby pressing the play key.

No operation occurs evenwhen an operation key ispressed.

The cassette holders cannotbe opened by pressing the“PUSH OPEN” area.

Sound is harsh or highfrequencies are not repro-duced.

Sound is distorted.

Noise is noticeable.

Sound vibrates.

Recording cannot be startedby pressing the record key.

R

¢

¢

¢

U

R

R

∞

R

∞

T¢

§

§

÷ The head is dirty.

÷ The tape is wound too tight due toirregular winding.

÷ A nonrecorded tape is played.

÷ The cassette holder is not closed com-pletely.

÷ The operation key is pressed immedi-ately after closing the cassette holder.

÷ The operation key is pressed in less than4 seconds after turning the power ON.

÷ A tape is not inserted in the unit.÷ The tape is wound too tight due to

irregular winding.÷ The tape is fully wound to one of the

reels.

÷ The key is pressed during recording orplayback.

÷ The microcomputer is malfunctioningdue to external noise.

÷ The head is dirty.

÷ The tape is stretched or shrunk.

÷ The recording level has not been ad-justed. (During Video 1, Video 2 inputoperation)

÷ The tape being played was recordedwith distorted sound.

÷ The tape head is magnetized.

÷ External noise is induced.

÷ A tape recorded with Dolby NR ON isplayed with "Dolby NR" off.

÷ The capstans or pinch rollers are dirty.

÷ The tape is wound irregularly.

÷ The recording protect tab of the cas-sette has been broken.

÷ The cassette holder is not closed com-pletely.

÷ The TAPE input is selected.

÷ The tape is fully wound to one of the reels.

Cassette deck

60

Know

ledg

e se

ctio

n

INDEX

[A]

A.R.M. ...................................................................... 27

ACTIVE indicator ...................................................... 11

Adjusting the display contrast ................................. 49

Adjusting the external input level ............................ 40

Adjusting the left and right volume balance ............ 17

Adjusting the subwoofer output level ..................... 40

AI timer playback ..................................................... 45

Auto preset ............................................................. 20

[B]

Basic use method .................................................... 16

[C]

Cable Tuner control screen ...................................... 53

CD direct recording .................................................. 37

CD one-track recording ............................................ 38

CD program recording ............................................. 39

CHANNEL SPACE setting ....................................... 10

Checking the time information display of CD .......... 48

Cleaning the head section ....................................... 54

Clock adjustment ..................................................... 14

Communication indicator ......................................... 11

CONFIRM/DEMO key ........................................... 6,13

[D]

Demonstration ........................................................... 6

Disc handling precautions ........................................ 55

Dolby Virtual setting ................................................ 42

DSP mode setting.................................................... 43

DSS control screen .................................................. 53

DVD control screen.................................................. 53

[E]

EON ......................................................................... 30

[F]

Fast forwarding/rewinding or skipping tape ............ 25

[H]

HOME key ............................................................... 13

[ I ]

In regard to CD-TEXT ............................................... 23

[M]

Maintenance ............................................................ 54

Manual preset ......................................................... 21

[N]

Normal timer playback ............................................. 45

Notes on cassette tape ........................................... 55

[O]

O.T.T. ....................................................................... 44

One-touch operation ................................................ 17

[P]

Playback of CD......................................................... 22

Playback of tape....................................................... 24

Program playback .................................................... 32

PTY search ............................................................... 29

[R]

R.D.S. ....................................................................... 28

Random playback ..................................................... 35

RDS auto memory ................................................... 20

Receiving broadcast station..................................... 18

Recording on TAPE .................................................. 26

Reference ................................................................ 54

Remote control of external components ................. 50

Repeated playback................................................... 34

[S]

Selecting Dolby NR .................................................. 25

Selecting the bass boost ......................................... 41

Selecting the reverse mode .................................... 25

Setting the timer playback ....................................... 45

Skipping tracks ......................................................... 23

Sleep Timer (Sleep).................................................. 46

Specifications ........................................................... 62

Standby mode .......................................................... 17

STANDBY/TIMER indicator ...................................... 17

Switching between stereo tuning and monaural tuning

................................................................................. 19

[T]

Timer operation ........................................................ 44

Timer recording ........................................................ 47

To eject the disc ...................................................... 23

To pause playback (CD) ........................................... 23

To receive a station that has not been preset ......... 19

To stop playback (CD) .............................................. 23

To stop playback (Tape) ........................................... 24

Tone adjustment ...................................................... 41

TV control screen ..................................................... 53

[V]

VCR control screen .................................................. 53

Volume adjustment. ................................................. 16

61

Knowledge section

Menu display chart

"TUNER" menu display

<Reception Mode>

Stereo/Mono

Stereo

Mono

Direct Tuning

<Memory>

Auto Memory (#2)

Auto Preset (#1)(#3)

Manual Memory

<RDS Mode>(#2)

EON ***(#2)

PTY ***(#2)

"CD" menu display

<Play Mode>

Repeat On (Off)

On

Off

Random On (Off)

On

Off

Program On (Off)

Set

Check

Off

"Tape" menu display

Dolby NR

On

Off

Direction

One Way

Reverse

Endless

"TV" remote display

"Video 1" remote display

"Video 2" remote display

"Function" menu display

<Sound Mode>

Listen Mode

Virtual

Virtual On (Off)

On

Off

Effect

DSP Mode

DSP On (Off)

Off

Stadium

Arena

Live house

Bass Boost On (Off)

(NV-500 only)

On

Off

Balance

Tone Control

Bass

Treble

Input Level

Video1

Video2

S.W. Level (NV-600 only)

<Time INFO> CD Single

CD Single TimeCD Total

CD Total Time <Timer Mode>

Sleep O.T.T.

On Off

Timer Play On

Source SelectOff

<Rec Options> CD→Tape Rec

One Track RecDirect RecProgram Rec

Timer Rec On (Off) On

Source Select Off

<Setup IR> TV

(manufacturer list) (type of codes )

Video 1 VCR (manufacturer list) (type of codes )

Cable (#1)


DSS (#1)


DVD (manufacturer list) (type of codes )

Video 2 VCR (manufacturer list) (type of codes )

Cable (#1)


DSS (#1)


DVD (manufacturer list) (type of codes )

<Display>Contrast

(#1) : This mark refers to item for the U.S.A. and Canada.(#2) : This mark refers to item for Europe and U.K.(#3) : This mark refers to item for other countries.

62

Know

ledg

e se

ctio

n

Specifications

[Amplifier section]Output power

(U.S.A. and Canada)Rated output power (front channel only)

30 watts per channel minimum RMS, both chan-nels driven, at 8 Ω from 100 Hz to 20 kHz with nomore than 0.9% total harmonic distortion.(FTC)

Effective output powerFRONT (1 kHz, 10 % T.H.D., at 8 Ω ) ............ 40 W + 40 WSUBWOOFER (65 Hz, 10 % T.H.D., at 4 Ω ) ........................ 80 W

(Europe and U.K.)Rated output power (front channel only) (DIN)

(1 kHz, 0.7 % T.H.D., at 8 Ω ) ............ 35 W + 35 WEffective output power

FRONT (1 kHz, 10 % T.H.D., at 8 Ω ) ............ 40 W + 40 WSUBWOOFER (65 Hz, 10 % T.H.D., at 4 Ω ) ........................ 80 W

(Other countories)Rated output power during (front channei only)

(1 kHz, 1 % T.H.D., at 8 Ω ) ............... 35 W + 35 WEffective output power during STEREO operation

FRONT (1 kHz, 10 % T.H.D., at 8 Ω ) ............ 40 W + 40 WSUBWOOFER (65 Hz, 10 % T.H.D., at 4 Ω ) ........................ 80 W

Frequency responceFRONT (VIDEO1/VIDEO2) ... 100 Hz ~ 40 kHz (+0 dB ~ -3 dB)SUBWOOFER (VIDEO1/VIDEO2) ....... 5 Hz ~ 100 Hz (+0 dB ~ -3 dB)

Signal to noise ratioVIDEO1/VIDEO2 .............................................. 90 dB

Input sensitivity/impedanceVIDEO1/VIDEO2

(U.S.A, Canada, Europe and U.K.) .... 230 mV/47 kΩ(Other countories) ......................... 200 mV/47 kΩ

Output level/impedanceREC OUT (VIDEO1)

(U.S.A, Canada, Europe and U.K.) .... 230 mV/470 Ω(Other countories) ......................... 200 mV/470 Ω

[Video section]Input / Output VIDEO

(Composite) ........................................... 1 Vp-p/75 Ω[Tuner section]FM tuner section

Tuning frequency range ........... 87.5 MHz ~ 108 MHz

Main unit (RXD-NV600)

[Satellite speaker system]Enclosure ..... Bass-reflex type, magnetically shieldedSpeaker configuration

Woofer ............................ 80 mm (3-1/8”), cone typeTweeter............................. 19 mm (3/4”), dome type

Impedance ................................................................ 8 ΩMaximum input level .............................................. 40 WDimensions .................................. W: 158 mm (6-1/4”)

H : 257 mm (10-1/8”)D : 152 mm (6”)

Weight (net) .... 2.0 kg (1 piece/including the speaker stand)

[Subwoofer system]Enclosure ..... Bass-reflex type, magnetically shieldedSpeaker configuration

Woofer .......................... 160 mm (6-1/2”), cone typeImpedance ................................................................ 4 ΩMaximum input level .............................................. 80 WDimensions .................................. W: 206 mm (8-1/8”)

H : 280 mm (11”)D : 387 mm (15-1/4”)

Weight (net) ............................................ 6.5 kg(1 piece)

KENWOOD follows a policy of continuous advancements in development. For this reason specifications may bechanged without notice.÷ Sufficient performance may not be exhibited at extremely cold locations (where water freezes).

NotesNotes

MW (AM) tuner sectionTuning frequency range

(For U.S.A and Canada) ...... 530 kHz ~ 1,700 kHz(For Europe and U.K,) ......... 531 kHz ~ 1,602 kHz(For other countories) 9 kHz step ........................ 531 kHz ~ 1,602 kHz 10 kHz step ........................ 530 kHz ~ 1,610 kHz

LW tuner section (For U.K. only)Tuning frequency range .............. 153 kHz ~ 279 kHz

[CD player section]Laser ..............................................Semiconductor laserWow and flutter............................. Unmeasurable limit

[Cassette deck section]Track ........................................ 4 track, 2 channel stereoRecording system ................................. AC bias system

(Frequency: 105 kHz)Heads

Playback / recording head ....................................... 1Erasing head ............................................................. 1

Motor .............................................................................. 1Fast winding time ........................ Approx. 110 seconds

(C-60 tape)

[General]Power consumption ............................................. 100 WDimensions (Attached the remote control unit)

............................................. W : 285 mm (11-1/4”) H : 252 mm (9-15/16”) D : 368 mm (14-1/2”)

Weight (Include the remote control unit) ......... 8.4 kg

Speakers (LS-NV600S)

NV-600

63

Knowledge section

Specifications


NotesNotes

[Amplifier section]

Output power(U.S.A. and Canada)Rated output power

100 watts per channel minimum RMS, all channelsdriven, at 6 Ω from 40 Hz to 20 kHz with no morethan 0.9% total harmonic distortion. (FTC)

(Europe and U.K.)Rated output power (DIN)

(1 kHz, 0.7 % T.H.D., at 6 Ω ) ............ 70 W + 70 WEffective output power

(1 kHz, 10 % T.H.D., at 6 Ω ) ........ 100 W + 100 W(Other countries)Rated output power

(1 kHz, 1 % T.H.D., at 6 Ω ) ............... 80 W + 80 WEffective output power

(1 kHz, 10 % T.H.D., at 8 Ω ) ........ 100 W + 100 W

Signal to noise ratioVIDEO1/VIDEO2 .............................................. 90 dB

Input sensitivity/impedanceVIDEO1/VIDEO2

(U.S.A and Canada) ...................... 300 mV/47 kΩ(Other countries) .......................... 250 mV/47 kΩ

Output level/impedanceREC OUT (VIDEO1)

(U.S.A and Canada) .......................300 mV/470 Ω(Other countries) ...........................250 mV/470 Ω

Super woofer preout(U.S.A and Canada) ........................... 1.8 V/3.3 kΩ(Other countries) ................................. 2 V/3.3 kΩ

[Video section]Input/ Output

(Composite) ........................................... 1 Vp-p/75 Ω

Main unit (RXD-NV500)

Enclosure ............................................. Bass-reflex typeSpeaker configuration

Woofer .......................... 160 mm (6-1/2”), cone typeTweeter................................ 25 mm (1”), dome type

Impedance ................................................................ 6 ΩMaximum input level ............................................ 100 WDimensions .............................. W : 225 mm (8-7/8”)

H : 350 mm (13-3/4”)D : 263 mm (10-3/8”)

Weight (net) ............................................ 5.0 kg(1 piece)


NotesNotes

[Tuner section]FM tuner section

Tuning frequency range ........... 87.5 MHz ~ 108 MHzMW (AM) tuner section

Tuning frequency range(U.S.A and Canada) ............. 530 kHz ~ 1,700 kHz(Europe and U.K,) ................ 531 kHz ~ 1,602 kHz(other countories) 9 kHz step ........................ 531 kHz ~ 1,602 kHz 10 kHz step ........................ 530 kHz ~ 1,610 kHz

LW tuner section (For U.K. only)Tuning frequency range .............. 153 kHz ~ 279 kHz

[CD player section]Laser ..............................................Semiconductor laserWow and flutter............................. Unmeasurable limit

[Cassette deck section]Track ........................................ 4 track, 2 channel stereoRecording system ................................. AC bias system

(Frequency: 105 kHz)Heads

Playback / recording head ....................................... 1Erasing head ............................................................. 1

Motor .............................................................................. 1Fast winding time ........................ Approx. 110 seconds

(C-60 tape)

[General]Power consumption

(U.S.A. and Canada) ........................................ 160 W(Other countories) ........................................... 130 W

Dimensions (Attached the remote control unit)............................................. W : 285 mm (11-1/4”)

H : 252 mm (9-15/16”) D : 368 mm (14-1/2”)

Weight (Include the remote control unit) ......... 8.4 kg

Speakers (LS-NV500)

NV-500

For your recordsRecord the serial number, found on the back of the unit, inthe spaces designated on the warranty card, and in thespace provided below. Refer to the model and serialnumbers whenever you call upon your dealer for informa-tion or service on this product.Model Serial Number

compact hifi system nv-500 nv-600manual.kenwood.com/files/b60-4290-00.pdfcompact hifi system nv-500...

Documents