columbia assembly manual
TRANSCRIPT
Manufacturer: Backyard Discovery 3001 North Rouse Pittsburg, KS 66762
Made in China
OWNER PS-2010 Rev. 10/21/2009
Tracking Number Reference Label Remove label sticker from each carton and stick on the back side of ID plate. In the event of warranty claim this will help identify your unit.
Staple Receipt Here
OWNER PS-2010 Rev. 10/21/2009
OWNER PS-2010 Rev. 10/21/2009
Material Uncompressed Depth Compressed Depth
6" (152mm) 9" (228mm) 12" (304mm) to 9" (228mm)
Wood Chips 7' (2.13m) 10' (3.05m) 11' (3.35m) 10' (3.05m)
Double-Shredded bark mulch 6' (1.83m) 10' (3.05m) 11' (3.35m) 7' (2.13m)
Engineered Wood Fibers 6' (1.83m) 7' (2.13m) >12' (3.66m) 6' (1.83m)
Fine Sand 5' (1.52m) 5' (1.52m) 9' (2.74m) 5' (1.52m)
Coarse Sand 5' (1.52m) 5' (1.52m) 6' (1.83m) 4' (1.22m)
Fine Gravel 5' (1.52m) 7' (2.13m) 10' (3.05m) 6' (1.83m)
Medium Gravel 5' (1.52m) 5' (1.52m) 6' (1.83m) 5' (1.52m)
Shredded Tires* 10-12' (3.0-3.6m) N/A N/A N/A
OWNER PS-2010 Rev. 10/21/2009
°
OWNER PS-2010 Rev. 10/21/2009
Basic Setup DimensionsPlace the set on level ground, not less than 6 ft [2 M] from any structure or obstruction such as a fence,
garage, house, overhanging branches, laundry lines or electrical wires.
Measuring hardware
INS--65110-1 12/7/09
(An Adult w/an (Phillips & Straight Blade (Rubber Mallet –Optional) Adult helper) screw drivers)
2Columbia Model 65110 • 10-0111
Table of ContentsBoard Identifi cation Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Materials List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Assembly Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Phase 1: Frame Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Phase 2: Frame Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Phase 3: Frame Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Phase 4: Frame Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Phase 5: Frame Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Phase 6: Floor Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Phase 7: Frame Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Phase 8: Frame Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Phase 9: Wall Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Phase 10: Wall Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Phase 11: Bench Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Phase 12: Seat Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Phase 13: Bench Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Phase 14: Table Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Phase 15: Ladder Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Phase 16: Rock Wall Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Phase 17: Rock Wall Ladder Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Phase 18: Sunburst Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Phase 19: Roof Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Phase 20: Roof Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Phase 21: Roof Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Phase 22: Roof Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Phase 23: Roof Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Phase 24: Roof Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Phase 25: Hand Grip Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Phase 26: Swing Beam Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Phase 27: Swing Beam Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Phase 28: Swing Beam Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Phase 29: Swing Beam Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Phase 30: Slide Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Phase 31: Slide Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Phase 32: Stake Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Phase 33: Swing and Glider Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3Columbia Model 65110 • 10-0111
3
Fron
tR
ight
Par
ts N
ot S
how
nE
2H
1
H3
K2
G1
J1
K6
M1
M4
M11
K9
M6
M12
N1
N3
N6
M13
J3
J3
K3
M3s
M3s
K1
K1K
3
J5
E3
E5
M5
M9sM8
J6
J4
J2
M10
M10
H2
M3s
J5
E1
F1
M7
H1
K4 K5
M9
M9
E4
H5S
K1
SK
2
N6
N4
N5
W10
0604
W10
0546
W10
0547
W10
0547
M2s
L1
H4
H6
H7
L2
4Columbia Model 65110 • 10-0111
Bac
k
Left
Par
ts N
ot S
how
nE
3H
7
J1K
5
F1 J2
M1
M7
M10
N2
M5
N1
N3
K3
E2
K1
E5
J3
J5
M3s
W10
0604
W10
0546
W10
0547
W10
0547
H6
H3K
9
M11
M4 E
4
M13
M12
M2s
L1
M8
M11
K3
E1
M6
M3s
H4
H5
G1
K6
K2
K4
H1
M9
J6
M6
H2
M9s
J4
M8
SK
2
SK
1
N6
N4
N5
L2
5Columbia Model 65110 • 10-0111
ID LETTER DESCRIPTION QTY.
E1 ——––——W100503 * Upright RGT Rear * 1-1/2 x 3-3/8 x 89-1/2 [36 x 86 x 2274mm] ––––––– 1 Req
E2 ——––—— W100504 * Upright LFT Rear * 1-1/2 x 3-3/8 x 89-1/2 [36 x 86 x 2274mm] –––––––– 1 Req
E3 ——––— W100505 * Upright RGT Front * 1-1/2 x 3-3/8 x 89-1/2 [36 x 86 x 2274mm] ––––––– 1 Req
E4 ——––— W100506 * Upright LFT Front * 1-1/2 x 3-3/8 x 89-1/2 [36 x 86 x 2274mm] ––––––– 1 Req
E5 ——––—— W100515 * Picnic Table Leg * 1-1/2 x 3-3/8 x 29-1/2 [36 x 86 x 750mm] –––––––– 2 Req
F1 ——––——— W100516 * Angle Brace * 1-1/2 x 2-1/4 x 14-1/8 [36 x 60 x 360mm] –––––––––– 4 Req
G1 ——––— W100502 * Swing Beam Support * 5/4 x 5-1/4 x 41-7/8 [24 x 134 x 1062mm] ––––––– 1 Req
H1 ——––——— W100507 * Roof Support * 5/4 x 3-3/8 x 69-5/8 [24 x 86 x 1768mm] –––––––––– 2 Req
H2 ——––——W100508 * Floor Support Board * 5/4 x 3-3/8 x 41-7/8 [24 x 86 x 1062mm] ––––––– 2 Req
H3 ——––—— W100533 * Ladder Rail LH * 5/4 x 3-3/8 x 50-5/8 [24 x 86 x 1286mm] ––––––––– 1 Req
H4 ——––—— W100534 * Ladder Rail MID * 5/4 x 3-3/8 x 50-5/8 [24 x 86 x 1286mm] ––––––––– 1 Req
H5 ——––—— W100536 * Ladder Rail RH * 5/4 x 3-3/8 x 50-5/8 [24 x 86 x 1286mm] ––––––––– 1 Req
H6 ——––———–W100535 * Ladder Rung * 5/4 x 3-3/8 x 13-1/8 [24 x 86 x 334mm] –––––––––– 4 Req
Materials List
6Columbia Model 65110 • 10-0111
H7 ——––———–– W100548 * Floor Cleat * 5/4 x 3-3/8 x 3-3/8 [24 x 86 x 86mm] –––––––––––– 4 Req
J1———––———W100514 * Porch Support * 5/4 x 2-1/4 x 42-1/8 [24 x 60 x 1072mm] ––––––––– 1 Req
J2———––———W100509 * Porch Support * 5/4 x 2-1/4 x 42-1/8 [24 x 60 x 1084mm] ––––––––– 1 Req
J3———––—W100510 * Picnic Table Seat Support * 5/4 x 2-1/4 x 41-1/2 [24 x 60 x 1056mm] ––––– 2 Req
J4———––———–W100511 * Porch Rafter * 5/4 x 2-1/4 x 36-3/8 [24 x 60 x 926mm] –––––––––– 2 Req
J5———––—— W100512 * Picnic Table Support * 5/4 x 2-1/4 x 29-1/4 [24 x 60 x 742mm] –––––––– 2 Req
J6———––——— W100513 * Rafter Support * 5/4 x 2-1/4 x 28-1/8 [24 x 60 x 715mm] –––––––––– 2 Req
K1 ——––——— W100495 * Long Board * 5/8 x 5-1/4 x 67-5/8 [16 x 134 x 1718mm] –––––––––– 2 Req
K2 ——––——W100497 * Porch Support Rail * 5/8 x 5-1/4 x 42-5/8 [16 x 134 x 1084mm] ––––––– 1 Req
K3 ——––— W100496 * Short Ground Board * 5/8 x 5-1/4 x 42-5/8 [16 x 134 x 1084mm] ––––––– 2 Req
K4 ——––———W100498 * Sculpted Rail * 5/8 x 5-1/4 x 42-5/8 [16 x 134 x 1084mm] ––––––––– 1 Req
K5 ——––———W100499 * Sculpted Rail * 5/8 x 5-1/4 x 41-7/8 [16 x 134 x 1062mm] ––––––––– 1 Req
K6 ——––———– W100500 * Wall Rail * 5/8 x 5-1/4 x 41-7/8 [16 x 134 x 1062mm] ––––––––––– 1 Req
K9 ——––—— W100537 * Ladder Support * 5/8 x 5-1/4 x 14-1/2 [16 x 134 x 370mm] ––––––––– 1 Req
7Columbia Model 65110 • 10-0111
L1———––——— W100531 * Floor Board * 5/8 x 4-1/2 x 39-7/8 [16 x 112 x 1012mm] –––––––––– 2 Req
L2———––——— W100978 * Top Wall Rail * 5/8 x 4-1/2 x 41-7/8 [16 x 112 x 1067mm] ––––––––– 1 Req
M1 ——––—— W100517 * Tarp Support Board * 5/8 x 3-3/8 x 44-1/2 [16 x 86 x 1132mm] –––––––– 3 Req
M2 ——––———–W100518 * Floor Board * 5/8 x 3-3/8 x 44-1/2 [16 x 86 x 1132mm] ––––––––– 10 Req
M3 ——––—— W100519 * Picnic Table Board * 5/8 x 3-3/8 x 42-5/8 [16 x 86 x 1084mm] ––––––– 10 Req
M4 ——––———– W100524 * Floor Rail * 5/8 x 3-3/8 x 42-5/8 [16 x 86 x 1084mm] ––––––––––– 1 Req
M5 ——––———– W100521 * Floor Rail * 5/8 x 3-3/8 x 42-5/8 [16 x 86 x 1084mm] ––––––––––– 1 Req
M6 ——––———––W100520 * Wall Rail * 5/8 x 3-3/8 x 41-7/8 [16 x 86 x 1062mm] ––––––––––– 2 Req
M7 ——––———––W100525 * Wall Rail * 5/8 x 3-3/8 x 42-5/8 [16 x 86 x 1084mm] ––––––––––– 1 Req
M8 ——––———W100527 * Wall BD Handle * 5/8 x 3-3/8 x 23-7/8 [16 x 86 x 606mm] ––––––––– 2 Req
M9 ——––———– W100526 * Wall Board * 5/8 x 3-3/8 x 23-7/8 [16 x 86 x 606mm] –––––––––– 13 Req
M10 ——––———–– W100528 * Wall Rail * 5/8 x 3-3/8 x 10 [16 x 86 x 254mm] ––––––––––––– 2 Req
M11 ——––———–– W100529 * Wall Rail * 5/8 x 3-3/8 x 4-7/8 [16 x 86 x 124mm] –––––––––––– 2 Req
M12 ——––———– W100532 * Rock Wall Slat * 5/8 x 3-3/8 x 18 [16 x 86 x 458mm] ––––––––––– 6 Req
8Columbia Model 65110 • 10-0111
M13 ——––———– W100538 * Rock Wall Slat * 5/8 x 3-3/8 x 18 [16 x 86 x 458mm] –––––––––– 2 Req
N1 ——––———– W100523 * Table Seat Cleat * 5/8 x 2-1/4 x 9 [16 x 60 x 230mm] ––––––––––– 2 Req
N2 ——––—— W100530 * Floor Support Cleat * 5/8 x 2-1/4 x 41-5/8 [16 x 60 x 1060mm] –––––––– 1 Req
N3 ——––—— W100522 * Picnic Table Cleat * 5/8 x 2-1/4 x 11-7/8 [16 x 60 x 300mm] ––––––––– 1 Req
N4 ——––———– W100043 * Cross Brace * 5/8 x 2-1/4 x 30-7/8 [16 x 60 x 784mm] –––––––––– 2 Req
N5 ——––———–– W100044 * Starburst * 5/8 x 2-1/4 x 13 [16 x 60 x 332mm] ––––––––––––– 2 Req
N6 ——––———–– W100045 * Starburst * 5/8 x 2-1/4 x 7-1/4 [16 x 60 x 184mm] –––––––––––– 4 Req
SK1 ——––———– W100542 * Rafter LH * 5/8 x 5-1/4 x 53-1/8 [16 x 134 x 1350mm] –––––––––– 2 Req
SK2 ——––———–W100543 * Rafter RH * 5/8 x 5-1/4 x 53-1/8 [16 x 134 x 1350mm] –––––––––– 2 Req
W100544 –———––— Slide Support * 5/8 x 3-3/8 x 17-1/4 [16 x 86 x 438mm] –––––––––––––– 1 Req
W100545 –———––— Slide Support * 5/8 x 3-3/8 x 17-1/4 [16 x 86 x 438mm] –––––––––––––– 2 Req
W100604 –———––— Swing Beam * 2 x 5-1/4 x 89-1/2 [50 x 134 x 2274mm] –––––––––––––– 1 Req
W100547 –———––—A-Frame Leg * 1-3/8 x 3-3/8 x 86-5/8 [34 x 86 x 2200mm] ––––––––––––– 2 Req
W100546 –———–A-Frame Ground Board * 5/4 x 3-3/8 x 88-3/8 [24 x 86 x 2246mm] –––––––––– 1 Req
9Columbia Model 65110 • 10-0111
0
1
2
3
4
5
6
7
8
9
ZHB-65110 Hardware BagPART. . . . . . . . . . . . . . . DESCRIPTION . . . . . . . . . . . . . . . QTY.H100115 . . . . . . . . . Washer Head Bolt (5/16 x 1/2") . . . . . . . . . . 7 ReqH100010 . . . . . . . . Washer Head Bolt (5/16 x 1-1/2") . . . . . . . . . . 29 ReqH100008 . . . . . . . . . Washer Head Bolt (5/16 x 1") . . . . . . . . . . . 8 ReqH100012 . . . . . . . . . Washer Head Bolt (5/16 x 2") . . . . . . . . . . . 21 ReqH100014 . . . . . . . . Washer Head Bolt (5/16 x 2-1/2") . . . . . . . . . . 3 ReqH100015 . . . . . . . . Washer Head Bolt (5/16 x 2-3/4") . . . . . . . . . . 4 ReqH100032 . . . . . . . . Washer Head Bolt (5/16 x 5-3/4") . . . . . . . . . . 4 ReqH100001 . . . . . . . . . . Flat Head Bolt (3/8 x 1-1/2") . . . . . . . . . . . 7 ReqH100042 . . . . . . . . . . . Hex Bolt (5/16 x 1-1/4") . . . . . . . . . . . . 4 ReqH100047 . . . . . . . . . . . Hex Bolt (5/16 x 2-3/4") . . . . . . . . . . . . 2 ReqH100061 . . . . . . . . Phillips Truss Head Bolt (1/4 x 1"). . . . . . . . . . 11 ReqH100038 . . . . . . . . . . . Carriage Bolt (5/16 x 2") . . . . . . . . . . . . 4 ReqH100027 . . . . . . . . Washer Head Lag Screw (5/16 x 2") . . . . . . . . . 31 ReqH100067 . . . . . . . . . . . .Lag Screw (5/16 x 2") . . . . . . . . . . . . . 11 ReqH100124 . . . . . . . . . . . Wood Screw (#8 x 1/2") . . . . . . . . . . . . 9 ReqH100088 . . . . . . . . . . Wood Screw (#8 x 1-1/8"). . . . . . . . . . . 118 ReqH100086 . . . . . . . . . . Wood Screw (#8 x 1-1/2"). . . . . . . . . . . 105 ReqH100111 . . . . . . . . . . . Wood Screw (#8 x 2") . . . . . . . . . . . . . 57 ReqH100092 . . . . . . . . . . . Wood Screw (#8 x 3") . . . . . . . . . . . . . 26 ReqH100123 . . . . . . . . . . Tapping Screw (#8 x 1/2"). . . . . . . . . . . . 56 ReqH100083 . . . . . . . . . . Tapping Screw (#14 x 3/4") . . . . . . . . . . . 4 ReqH100072 . . . . . . . . . . . . .Spike T-Nut (1/4") . . . . . . . . . . . . . . 4 ReqH100073 . . . . . . . . . . . . .Spike T-Nut (3/8") . . . . . . . . . . . . . . 7 ReqH100074 . . . . . . . . . . . . Spike T-Nut (5/16") . . . . . . . . . . . . . 4 ReqH100004 . . . . . . . Washer Head Barrel Nut (5/16 x 5/8"). . . . . . . . . 7 ReqH100005 . . . . . . . Washer Head Barrel Nut (5/16 x 7/8"). . . . . . . . . 62 ReqH100110 . . . . . . . . . . . . . Lock Nut (5/16") . . . . . . . . . . . . . . 22 ReqH100079 . . . . . . . . . . . Barrel Nut (1/4 x 3/4") . . . . . . . . . . . . . 7 ReqH100103 . . . . . . . . . . Safety Washer (17 x 30mm) . . . . . . . . . . . 4 ReqH100106 . . . . . . . . . . . Flat Washer (9 x 18mm) . . . . . . . . . . . . 28 ReqH100105 . . . . . . . . . . Fender Washer (8 x 27mm) . . . . . . . . . . . 28 Req H100030 . . . . . . . . . . . Star Washer (8 x 19mm) . . . . . . . . . . . . 89 ReqH100031 . . . . . . . . . . Star Washer (12 x 19mm). . . . . . . . . . . . 68 ReqH100095 . . . . . . . . . . . . Split Washer (5/16") . . . . . . . . . . . . . 4 ReqH100108 . . . . . . . Internal Tooth Lock Washer (8 x 15mm) . . . . . . . . 22 ReqH100097 . . . . . . . Swing Hanger Quick Link Bolt (1-5/8") . . . . . . . . 4 ReqH100099 . . . . . . . Swing Hanger Quick Link Bolt (5-1/4") . . . . . . . . 4 Req
10 • 10-0111
A100043Hand Grip
2 Req
Y41Metal Stake
6 Req
X21-GRock6 Req
A100041Wrench T-40
2 Req
A100042Bit T-402 Req
04240q
NOTE: QUANTITIES INCLUDE EXTRA HARDWARE
10Columbia Model 65110 • 10-0111
Y30-21GL Bracket
2 Req
A100004Angle Bracket (5")
1 Req
Y20-LGLeft Beam Clamp
1 Req
Y20-RGRight Beam Clamp
1 Req
Y20-EGEnd Plate
1 Req
Y25-GGlider Support
2 Req
Y28-G4Swing Bushing
4 Req
X14Glider Support Cap
4 Req
A100023Glider Seat
1 Req
A100022Glider Arm
2 Req
A10001538.5"Chain4 Req
ZQLQuick Link
8 Req
Y6051.25"Chain4 Req
X2-Y Swing Seat
2 Req
X15-8YSSlide1 Req
X15-8GLSlide Rail Left
1 Req
X15-8GR Slide Rail Right
1 Req
0
1
2
3
4
5
6
7
8
9
Y20-LGLeft Beam C
1 Req
-RGm Clamp
Req
Y2En
1
Y50-LTPLeisure Time ID Plate
2 Req
A100040Tent Top
(1038mm x 1076mm)1 Req
A100039Tent Top
(1132mm x 2931mm)1 Req
11Columbia Model 65110 • 10-0111
0
1
2
3
4
5
6
7
8
9
ME
AS
UR
E B
OLTS
FRO
M
BO
TTOM
OF H
EA
D TO
B
OTTO
M O
F BO
LT
H1000275/16 x 2"
Washer HeadLag Screw
H1000308 x 19mm
Star Washer
H10006715/16" x 2"Lag Screw
H1000721/4"
Spike T-Nut
H1000733/8"
Spike T-Nut
H1000971-5/8"
Swing Hanger Quick Link Bolt
H1000995-1/4"
Swing Hanger Quick Link BoltH100105
8 x 27mmFender Washer
H1001069 x 18mm
Flat Washer
H1001088 x 15mm
Internal Tooth Lock Washer
H1001105/16"
Lock Nut
H10003112 x 19mm
Star Washer
H10004215/16" x 1-1/4"
Hex Bolt
H10004715/16" x 2-3/4"
Hex Bolt
H10010317 x 30mm
Safety Washer
H10009515/16"
Split Washer
H1000745/16"
Spike T-Nut
12Columbia Model 65110 • 10-0111
DRAWINGS ARE TO SCALE BUT SMALL VARIATIONS ARE NORMAL.
0
1
2
3
4
5
6
7
8
9H100001
3/8 x 1-1/2"Flat Head
Bolt
H1000085/16 x 1"
Washer Head Bolt H100010
5/16 x 1-1/2"Washer Head
Bolt H1000125/16 x 2"
Washer Head Bolt H100014
5/16 x 2-1/2"Washer Head
Bolt
H1000155/16 x 2-3/4"Washer Head
Bolt
H1000325/16 x 5-3/4"Washer Head
Bolt
H100086#8 x 1-1/2"
Wood Screw
H100088#8 x 1-1/8"
Wood Screw
H100092#8 x 3"
Wood Screw
H100111#8 x 2"
Wood Screw
H1001155/16 x 1/2"
Washer Head Bolt
H100124#8 x 1/2"
Wood Screw
H1000611/4-20 x 1"
PhillipsTruss Head Bolt
H100083#14 x 3/4"
Tapping Screw
H100123#8 x 1/2"
Tapping Screw
H1000045/16 x 5/8"
Washer Head Barrel Nut
H1000055/16 x 7/8"
Washer Head Barrel Nut
H1000791/4-20 x 3/4"
Barrel Nut
H1000385/16 x 2"
Carriage Bolt
13Columbia Model 65110 • 09-10-0111
Items needed for this phase: Hardware needed for this phase:
13
Washer Head Bolt * 5/16 x 1-1/2" * 8 Req Washer Head Bolt * 5/16 x 2" * 4 ReqStar Washer * 8 x 19mm * 12 ReqStar Washer * 12 x 19mm * 12 ReqWasher Head Barrel Nut * 5/16 x 7/8" * 12 Req
E1 * Upright RGT Rear * 1 ReqE2 * Upright LFT Rear * 1 ReqG1 * Swing Beam Support * 1 ReqK1 * Long Ground Board * 1 ReqK6 * Wall Rail * 1 Req
Note: When assembling the Columbia, position the boards so that the stamps are hidden.Step 1: Attach K1 to E1 and E2 with 1-1/2" head bolts, star washers, and 7/8" barrel nuts. Attach K6 to E1 and E2 with 1-1/2" head bolts, star washers, and 7/8" barrel nuts. Attach G1 to E1 and E2 with 2" head bolts, star washers, and 7/8" barrel nuts.
Phase 1: Frame Assembly
Pilot holes
should be on
the outside.
G1
K6
E2E1
K1
2" Head Bolt
H10003112 x 19mm
H1000308 x 19mm
14Columbia Model 65110 • 10-0111
Items needed for this phase: Hardware needed for this phase:Washer Head Bolt * 5/16 x 1-1/2" * 8 Req Star Washer * 8 x 19mm * 8 ReqStar Washer * 12 x 19mm * 8 ReqWasher Head Barrel Nut * 5/16 x 7/8" * 8 Req
E3 * Upright RGT Front * 1 ReqE4 * Upright LFT Front * 1 ReqK1 * Long Ground Board * 1 ReqK5 * Sculpted Rail * 1 Req
Step 2: Attach K1 to E3 and E4 with 1-1/2" head bolts, star washers, and 7/8" barrel nuts. Attach K5 to E3 and E4 with 1-1/2" head bolts, star washers, and 7/8" barrel nuts.
Phase 2: Frame Assembly
Pilot holes should
be on the outside.
E3
E4
K5
K1
15Columbia Model 65110 • 09-10-0111
Items needed for this phase: Hardware needed for this phase:Washer Head Lag Screw * 5/16 x 2" * 14 ReqStar Washer * 8 x 19mm * 14 ReqWood Screw * #8 x 1-1/2" * 4 Req
K2 * Porch Support Rail * 1 ReqK3 * Short Ground Board * 2 ReqK4 * Sculpted Rail * 1 Req
Step 3: Attach one K3 to E1 and E3 with 2" washer head lag screws and star washers. Attach the remaining K3 to E2 and E4 with 2" washer head lag screws and star washers.
Step 4: Attach K4 to E2 and E4 with 2" washer head lag screws and star washers.
Step 5: Attach K2 to E1 and E3 with 2" washer head lag screws and star washers in the bottom holes, and 1-1/2" wood screws in the other holes.
Phase 3: Frame Assembly
Always drill pilot holes when using lag screws.
Typical Installation - Washer HeadLag Screw
StarWasher
Washer Head Lag Screw
Do not over-tighten.
Typical Installation - Wood Screw• Use an electric drill or screw gun to drive screws.• These screws are self-tapping, so no pilot holes
are required.• Lubricate the threads of the screws with beeswax
or soap to ease installation and minimize breaking screws.
• It is important that the tops of all screws are fl ush with the surface of the wood and there are no protruding sharp edges.
Do not drive too deep and cause splintering.
ad
ag
ag
K4
K2
E2
E3
E4
E1
1-1/2" Wood Screws
K3
E4
E2
E1
E3
K3
16Columbia Model 65110 • 10-0111
Items needed for this phase: Hardware needed for this phase:Washer Head Bolt * 5/16 x 2-3/4" * 4 ReqStar Washer * 8 x 19mm * 4 ReqStar Washer * 12 x 19mm * 4 ReqWasher Head Barrel Nut * 5/16 x 7/8" * 4 Req
H2 * Floor Support Board * 2 ReqH7 * Floor Cleat * 4 Req
Step 6: Attach one H2 to E1, E2, and the H7s with 2-3/4" head bolts, star washers, and 7/8" barrel nuts. Attach the remaining H2 to E3, E4, and the H7s with 2-3/4" head bolts, star washers, and 7/8" barrel nuts.
Phase 4: Frame Assembly
o E1, E2, and 3/4" head bolts, nd 7/8" barrel remaining
nd the H7sd bolts, star /8" barrel nuts.
E4
E2E3
E1
H7
H2
H2
H2 H7E3
17Columbia Model 65110 • 09-10-0111
Items needed for this phase: Hardware needed for this phase:Washer Head Lag Screw * 5/16 x 2" * 4 ReqWasher Head Bolt * 5/16 x 1-1/2" * 2 ReqWasher Head Bolt * 5/16 x 2" * 2 ReqLag Screw * 5/16 x 2" * 4 ReqWasher Head Barrel Nut * 5/16 x 7/8" * 4 ReqInternal Tooth Lock Washer * 8 x 15mm * 4 ReqStar Washer * 8 x 19mm * 8 ReqStar Washer * 12 x 19mm * 4 ReqFlat Washer * 9 x 18mm * 4 Req
F1 * Angle Brace * 4 ReqM4 * Floor Rail * 1 ReqM5 * Floor Rail * 1 Req
Phase 5: Frame Assembly
Step 7: Attach M4 to E2 and E4 with 2" washer head lag screws and star washers.Step 8: Attach M5 to E1 and E3 with 2" washer head lag screws and star washers. Note: Level and plumb the corners of the frame.Step 9: Attach the top holes of two F1s to the backside of M5 with 1-1/2" head bolts, star washers, and 7/8"
barrel nuts. Attach the other end of the F1s to the faces of E1 and E3 with 2" lag screws, lock washers, and fl at
washers.Step 10: Attach the top holes of the remaining F1s to the backside of H2 with 2" head bolts, star washers, and
7/8" barrel nuts.
17Columbia Model 65110 • 09-10-0111
E2
E1
E3
E4
M5
M4
E1 E3
M5 F1
1-1/2" Head Bolt
E2 E1
H2 F1
2" Head Bolt
Attach the other end of the F1s to the insides of E1 and E2 with 2" lag screws, lock washers, and fl at washers. If H2 does not have holes for the F1s, pre-drill the holes using a 3/8" drill bit.
Note: Use F1 as a guide for proper hole placement.
18Columbia Model 65110 • 10-0111
Items needed for this phase: Hardware needed for this phase:Wood Screw * #8 x 1-1/2" * 48 ReqWood Screw * #8 x 1-1/8" * 12 Req Tapping Screw * 3/4" * 4 Req
L1 * Floor Board * 2 ReqM2 * Floor Board * 10 ReqN2 * Floor Support Cleat * 1 ReqY30-21G * L Bracket * 2 Req
Step 11: Attach one L1 to the H7s with 1-1/2" wood screws. L1 should hang over M4 1/4". Attach the M2s to the H2s with 1-1/2" wood screws. Note: The holes on the M2s need to be centered
on the H2s, and should be even on each end. Attach the remaining L1 to the H7s with 1-1/2" wood screws. L1 should hang over M5 3/4".Step 12: Attach N2 to the underside of the M2s with 1-1/8" wood screws. N2 should be centered on the M2s. Attach one end of the L-brackets to each end of N2 with 3/4" tapping screws. Attach the opposite end of the L-brackets to M4 and M5 with 3/4" tapping screws.
Phase 6: Floor Assembly
Attach the opposite end of the L brackets to M4 and M5 wit
M4
L1
L1
M2s
M2s
M4
N2
N2
H2
19Columbia Model 65110 • 09-10-0111
Items needed for this phase: Hardware needed for this phase:Washer Head Bolt * 5/16 x 1-1/2" * 2 Req Washer Head Lag Screw * 5/16 x 2" * 2 ReqStar Washer * 8 x 19mm * 4 ReqStar Washer * 12 x 19mm * 2 ReqWasher Head Barrel Nut * 5/16 x 7/8" * 2 Req
M6 * Wall Rail * 1 ReqM7 * Wall Rail * 1 Req
Step 13: Attach M6 to E1 and E2, on top of the M2s, with 1-1/2" head bolts, star washers, and 7/8" barrel nuts.Step 14: Attach M7 to E1 and E3, on top of the M2s, with 2" washer head lag screws and star washers.
Phase 7: Frame Assembly
1965110 • 09 10 0111
M2s
E1
E3E2
M6M7
1-1/2" Head Bolt
20Columbia Model 65110 • 10-0111
Items needed for this phase: Hardware needed for this phase:Washer Head Bolt * 5/16 x 1-1/2" * 2 Req Washer Head Lag Screw * 5/16 x 2" * 2 ReqStar Washer * 8 x 19mm * 4 ReqStar Washer * 12 x 19mm * 2 ReqWasher Head Barrel Nut * 5/16 x 7/8" * 2 Req
M10 * Wall Rail * 2 ReqM11 * Wall Rail * 2 Req
Step 15: Attach the M10s to E3 and E4, on top of the M2s, with 1-1/2" head bolts, star washers, and 7/8" barrel nuts.
Step 16: Attach the M11s to E2 and E4, on top of the M2s, with 2" washer head lag screws and star washers.
Phase 8: Frame Assembly
20lumbia Model 65110 • 10-0111
barrel nuts.tep 16: Attach the M11s to E2 and E4, on top of the M2s, with 2" washer head lag screws and star washers.
1-1/2" Head Bolt
M2s
E3E2
E4
M10M11
21Columbia Model 65110 • 09-10-0111
Items needed for this phase: Hardware needed for this phase:Wood Screw * #8 x 1-1/8" * 44 ReqM9 * Wall Board * 11 Req
Phase 9: Wall Assembly
K2
M9sM7
M9s
M6
K6
Step 17: Attach six M9s to the inside of M7 and K2 with 1-1/8" wood screws. The M9s should be 2-3/4" apart.
Step 18: Attach fi ve M9s to the inside of M6 and K6 with 1-1/8" wood screws. The M9s should be about 3" apart.
22Columbia Model 65110 • 10-0111
Items needed for this phase: Hardware needed for this phase:Wood Screw * #8 x 1-1/8" * 16 Req
Step 19: Attach two M9s to the inside of K5 and the M10s with 1-1/8" wood screws. The M9s should be fl ush with the ends of the M10s.
Step 20: Attach the M8s to the inside of K4 and the M11s with 1-1/8" wood screws.
Phase 10: Wall Assembly
M8 * Wall BD Handle * 2 Req M9 * Wall Board * 2 Req
K5
M10
M9
M9
M8K4
M11
23Columbia Model 65110 • 09-10-0111
Items needed for this phase: Hardware needed for this phase:Washer Head Bolt * 5/16 x 1-1/2" * 4 ReqWasher Head Bolt * 5/16 x 2" * 4 Req Star Washer * 8 x 19mm * 8 ReqStar Washer * 12 x 19mm * 8 ReqWasher Head Barrel Nut * 5/16 x 7/8" * 8 Req
E5 * Picnic Table Leg * 2 ReqJ3 * Picnic Table Seat Support * 2 Req
Step 21: Attach the E5s to the K1s with 1-1/2" head bolts, star washers, and 7/8" barrel nuts.
Step 22: Attach one J3 to E1 and E5 with 2" head bolts, star washers, and 7/8" barrel nuts. Attach the remaining J3 to E3 and E5 with 2" head bolts, star washers, and 7/8" barrel nuts.
Phase 11: Bench Assembly
Step 22: Atstrest
K1
K1
E5
E5
E5
E5
E1
E3
J3
24Columbia Model 65110 • 10-0111
Items needed for this phase: Hardware needed for this phase:Wood Screw * #8 x 1-1/8" * 6 ReqWood Screw * #8 x 1-1/2" * 12 Req
Step 23: Attach one N1 to the underside of three M3s with 1-1/8" wood screws. Repeat this procedure to make another seat.
Step 24: Attach one seat to J3, fl ush against E1 and E3, with 1-1/2" wood screws.
Attach the remaining seat fl ush to the ends of J3 with 1-1/2" wood screws.
Phase 12: Seat Assembly
M3 * Picnic Table Board * 6 ReqN1 * Table Seat Cleat * 2 Req
M3s
M3s
M3s
M3s
N1
E3
J3
J3
E1
25Columbia Model 65110 • 09-10-0111
Items needed for this phase: Hardware needed for this phase:Washer Head Bolt * 5/16 x 1-1/2" * 1 ReqWasher Head Bolt * 5/16 x 2" * 3 ReqWasher Head Bolt * 5/16 x 2-1/2" * 1 ReqWasher Head Barrel Nut * 5/16 x 7/8" * 5 ReqStar Washer * 8 x 19mm * 5 ReqStar Washer * 12 x 19mm * 5 Req
Step 25: Attach one J5 to E3 and E5 with 2" head bolts, star washers, and 7/8" barrel nuts. Attach the remaining J5 to E5 with a 2" head bolt, star washers, and 7/8" barrel nut.Step 26: Attach one end of M6 to E1 and J5 with a 2-1/2" head bolt, star washers, and 7/8" barrel nut. Attach
the other end of M6 to E2 with a 1-1/2" head bolt, star washers, and 7/8" barrel nut.
Phase 13: Bench Assembly
J5 * Picnic Table Support * 2 ReqM6 * Wall Rail * 1 Req
25
J5
J5
E5
E3E5
J5
E2
E1
M6
26Columbia Model 65110 • 10-0111
Items needed for this phase: Hardware needed for this phase:Wood Screw * #8 x 1-1/8" * 4 ReqWood Screw * #8 x 1-1/2" * 8 Req
Step 27: Attach N3 to the underside of four M3s with 1-1/8" wood screws to make the table.
Step 28: Attach the table to the J5s, fl ush with the edge of the E5s, with 1-1/2" wood screws.
Phase 14: Table Assembly
M3 * Picnic Table Board * 4 ReqN3 * Picnic Table Cleat * 1 Req
26
J5
E5
J5
E5
M3sN3
27Columbia Model 65110 • 09-10-0111
Items needed for this phase: Hardware needed for this phase:
Step 29: Attach the H6s to H3 and H4 with 2" wood screws.Step 30: Attach K9 to the back of H3 and H4 with 2" wood screws. K9 should be attached 1" from the top of
the fi rst ladder rung.
Phase 15: Ladder Assembly
H3 * Ladder Rail LH * 1 ReqH4 * Ladder Rail MID * 1ReqH6 * Ladder Rung * 4 ReqK9 * Ladder Support * 1 Req
Wood Screw * #8 x 2" * 20 Req
H6
H6
H6
H6
H3
H4
H3
H4
K9
28Columbia Model 65110 • 10-0111
Items needed for this phase: Hardware needed for this phase:
Step 31: Insert 1 spike t-nut into each of the M12s. Attach one rock to each M12 with 1-1/2" fl at head bolts and 1-1/8" wood screws.Step 32: Attach the M12s and the M13s to H4 and H5 with 2" wood screws. The M12s and M13s should be
about 2-7/8" apart.
Phase 16: Rock Wall Assembly
H5 * Ladder Rail RH * 1 Req M12 * Rock Wall Slat * 6 ReqM13 * Rock Wall Slat * 2 ReqX21-G * Rock * 6 Req
Spike T-Nut * 3/8" * 6 ReqFlat Head Bolt * 1-1/2" * 6 ReqWood Screw * #8 x 1-1/8" * 6 ReqWood Screw * #8 x 2" * 32 Req
M12
H5
H4
M13
M13
M12
M12
1-1/8" Wood Screw
29Columbia Model 65110 • 09-10-0111
Items needed for this phase: Hardware needed for this phase:
Step 33: Drill 3/16" pilot holes in the rails. Position the rock wall ladder assembly as shown, and center the rock wall ladder rails on the pre-
drilled holes in M4. Attach the rock wall ladder assembly to M4 with 2" washer head lag screws and star washers.
Phase 17: Rock Wall Ladder Assembly
Washer Head Lag Screw * 5/16 x 2" * 3 ReqStar Washer * 8 x 19mm * 3 Req
M4
M4
30Columbia Model 65110 • 10-0111
Items needed for this phase: Hardware needed for this phase:
Step 34: Attach an ID plate to N4, N5, and N6 with 1/2" wood screws. Repeat this procedure to make another sunburst.
Phase 18: Sunburst Assembly
N4 * Cross Brace * 2 ReqN5 * Starburst * 2 ReqN6 * Starburst * 4 ReqY50-LTP * Leisure Time ID Plate * 2 Req
Wood Screw * #8 x 1/2" * 8 Req
N4
N5
N6
N6
31Columbia Model 65110 • 09-10-0111
Items needed for this phase: Hardware needed for this phase:
Phase 19: Roof Assembly
H1 * Roof Support * 2 ReqSK1 * Rafter LH * 1 Req SK2 * Rafter RH * 1 Req
Washer Head Bolt * 5/16 x 1" * 4 ReqWasher Head Barrel Nut * 5/16 x 7/8" * 4 ReqStar Washer * 8 x 19mm * 4 ReqStar Washer * 12 x 19mm * 4 ReqWood Screw * #8 x 1-1/8" * 20 Req
31
SK2
H1
SK1
SK2
SK1
Step 35: Attach SK1 and SK2 to H1 with 1" head bolts, star washers, and 7/8" barrel nuts. Repeat this procedure to make the other roof frame.
Step 36: Attach the sunburst assembly to SK1 and SK2 with 1-1/8" wood screws. Repeat this procedure to make the other roof frame.
32Columbia Model 65110 • 10-0111
Items needed for this phase: Hardware needed for this phase:
Step 37: Attach one M1 to the ends of the left SK1s, fl ush with the edge, with 1-1/2" wood screws. Attach one M1 to the ends of the right SK2s, fl ush with the edge, with 1-1/2" wood screws.Step 38: Attach the remaining M1 to the tops of the SK1s and SK2s with 1-1/2" wood screws. M1 should be
under the lip of the SK1s and SK2s, leaving room for the tarp to slide in-between.
Phase 20: Roof Assembly
M1 * Tarp Support Board * 3 Req Wood Screw * #8 x 1-1/2" * 12 Req
32
under the lip of the SK1s and SK2s, leaving room for the tarp to slide in-between.
SK2
SK1
SK2
SK1
M1
M1
M1
33Columbia Model 65110 • 09-10-0111
Items needed for this phase: Hardware needed for this phase:
Phase 21: Roof Assembly
Tent Top * 1132mm x 2931mm * 1 Req Tapping Screw * #8 x 1/2" * 28 ReqItems needed for this phase: HardwaTent Top * 1132mm x 2931mm * 1 Req Tapping
SK1
SK1
M1
Step 39: Center a tarp over the top M1, and attach it with 1/2" tapping screws, spaced evenly.
Step 40: Pre-drill the holes with a 1/8" drill bit. Pull one side of the tarp tight over the left M1.
Attach the tarp to the small wood strip on the SK1s with 1/2" tapping screws. Start at the peak and alternate sides.
Roll the tarp around M1 and attach it to the inside with 1/2" tapping screws.
Repeat this procedure to attach the tarp to the other side of the roof.
34Columbia Model 65110 • 10-0111
Items needed for this phase: Hardware needed for this phase:
Step 41: Attach L2 to E1 and E2 with 1-1/2" wood screws.
Step 42: Attach the roof assembly to E1, E2, E3, and E4 with 2" head bolts, star washers, and 7/8" barrel nuts.
Phase 22: Roof Assembly
Wood Screw * #8 x 1-1/2" * 4 ReqWasher Head Bolt * 5/16 x 2" * 4 ReqWasher Head Barrel Nut * 5/16 x 7/8" * 4 ReqStar Washer * 8 x 19mm * 4 ReqStar Washer * 12 x 19mm * 4 Req
34Columbia Model 65110 • 10-0111
E1
E2
E4E3
L2 * Top Wall Rail * 1 Req
E1 E2
L2
35Columbia Model 65110 • 09-10-0111
Items needed for this phase: Hardware needed for this phase:
Step 43: Attach the J4s to J1 with 1-1/2" wood screws.Step 44: Attach J2 to the J4s with 1-1/2" wood screws.Step 45: Attach the tarp to the front of J2 with 1/2" tapping screws. Pull the tarp tight, and then wrap it over J1. Attach it to J1 with 1/2" tapping screws. Attach the tarp to the J4s with 1/2" tapping screws.
Phase 23: Roof Assembly
J1 * Porch Support * 1 ReqJ2 * Porch Support * 1 ReqJ4 * Porch Rafter * 2 ReqTent Top * 1038mm x 1076mm * 1 Req
Tapping Screw * #8 x 1/2" * 20 ReqWood Screw * #8 x 1-1/2" * 8 Req
3565110 09 10 0111
J1
J2
J4
J4
J4
J2
36Columbia Model 65110 • 10-0111
Items needed for this phase: Hardware needed for this phase:
Step 46: Attach J1 to K2 with 1" head bolts, star washers, and 7/8" barrel nuts.
Step 47: Attach one J6 to E1 with a 2" lag screw, lock washer, and fl at washer.
Attach the remaining J6 to E3 with a 2" lag screw, lock washer, and fl at washer.
Attach the J6s to the J4s with 2" lag screws, lock washers, and fl at washers.
Phase 24: Roof Assembly
J6 * Rafter Support * 2 Req Lag Screw * 5/16" x 2" * 6 ReqWasher Head Bolt * 5/16 x 1" * 3 ReqWasher Head Barrel Nut * 5/16 x 7/8" * 3 ReqStar Washer * 8 x 19mm * 3 ReqStar Washer * 12 x 19mm * 3 ReqFlat Washer * 9 x 18mm * 6 ReqInternal Tooth Lock Washer * 8 x 15mm * 6 Req
J1
J6
J6
J4
E3
E1
K2
37Columbia Model 65110 • 09-10-0111
Items needed for this phase: Hardware needed for this phase:
Step 48: Insert 2 spike t-nuts into the M8s.Step 49: Attach the hand grips to the
M8s with 1" truss head bolts, fl at washers, and lock washers.
Phase 25: Hand Grip Assembly
X35-Y * Hand Grip * 2 Req Phillips Truss Head Bolt * 1/4 x 1" * 4 ReqInternal Tooth Lock Washer * 8 x 15mm * 4 ReqSpike T-Nut * 1/4" * 4 ReqFlat Washer * 9 x 18mm * 4 Req
M8
M8
M8
38Columbia Model 65110 • 10-0111
Items needed for this phase: Hardware needed for this phase:
Step 50: Attach the 5" angle brackets fl ush to the end of the swing beam with 2-3/4" hex bolts, lock nuts, and fender washers.
Step 51: Attach the left and right beam clamps to the opposite end of the swing beam with 2-1/2" head bolts, lock nuts, and fender washers.
Step 52: Attach the end plate to the end of the swing beam with 2" washer head lag screws.
Phase 26: Swing Beam Assembly
Swing Beam * 1 ReqY46-5G * Angle Bracket (5") * 1 ReqY20-LG * Left Beam Clamp * 1 ReqY20-RG * Right Beam Clamp * 1 Req
Washer Head Bolt * 5/16 x 2-1/2" * 2 Req Washer Head Lag Screw * 5/16 x 2" * 2 ReqLock Nut * 5/16" * 4 ReqFender Washer * 8 x 27mm * 6 ReqHex Bolt * 5/16" x 2-3/4" * 2 Req
Swing Beam
Swing Beam
Swing Beam
39Columbia Model 65110 • 09-10-0111
Items needed for this phase: Hardware needed for this phase:
39
Step 53: Attach the left A-frame leg to the end plate and left beam clamp with 2" carriage bolts, lock nuts, and fender washers.
Attach the right A-frame leg to the end plate and the right beam clamp with 2" carriage bolts, lock nuts, and fl at washers.
Step 54: Attach the A-frame ground board to the A-frame legs with 2" head bolts, star washers, and 7/8" barrel nuts.
Phase 27: Swing Beam Assembly
A-Frame Leg * 2 ReqA-Frame Ground Board * 1 ReqY20-EG * End Plate * 1 Req
Washer Head Bolt * 5/16 x 2" * 2 ReqCarriage Bolt * 5/16 x 2" * 4 ReqLock Nut * 5/16" * 4 ReqFender Washer * 8 x 27mm * 4 ReqStar Washer * 8 x 19mm * 2 ReqStar Washer * 12 x 19mm * 2 ReqWasher Head Barrel Nut * 5/16 x 7/8" * 2 Req
A-Frame Leg
A-Frame Leg
A-Frame Leg
A-Frame Leg
A-Frame Ground Board
40Columbia Model 65110 • 10-0111
Items needed for this phase: Hardware needed for this phase:
Step 55: Insert the swing hanger bolts into the top of the swing beam. Secure the swing hanger bolts with lock nuts, fender washers, and safety washers.
Step 56: Attach the glider supports to the swing beam with 5-3/4" head bolts, lock nuts, and fender washers, and 2" washer head lag screws.
Step 57: Insert the swing hanger bolts into the glider supports, and then secure the swing hanger bolts with fender washers, lock nuts, and swing bushing.
Insert the glider caps into the ends of the glider supports.
Phase 28: Swing Beam Assembly
Y25-G * Glider Support * 2 ReqY28-G4 * Swing Bushing * 4 ReqX14 * Glider Support Cap * 4 Req
Washer Head Lag Screw * 5/16 x 2" * 2 ReqWasher Head Bolt * 5/16 x 5-3/4" * 2 ReqSwing Hanger Quick Link Bolt * 1-5/8" * 4 ReqSwing Hanger Quick Link Bolt * 5-1/4" * 4 ReqLock Nut * 5/16" * 10 Req Fender Washer * 8 x 27mm * 10 ReqSafety Washer * 17 x 30mm * 4 Req
41Columbia Model 65110 • 09-10-0111
Items needed for this phase: Hardware needed for this phase:
Step 58: Insert 4 spike t-nuts into G1. Attach the swing beam to G1 with the 1-1/4" hex bolts, fender washers, and split washers.
Phase 29: Swing Beam Assembly
Hex Bolt * 5/16" x 1-1/4" * 4 ReqFender Washer * 8 x 27mm * 4 ReqSpike T-Nut * 5/16" * 4 Req Split Washer * 5/16" * 4 Req
G1
G1
42Columbia Model 65110 • 10-0111
Items needed for this phase: Hardware needed for this phase:
Step 59: Use the slide brace as a guide to pre-drill the holes. Attach the slide brace to the underside, bottom of the slide with 1/2" head bolts, star washers, and 5/8" barrel nuts.
Step 60: Insert the slide into the slide cavity in the right slide rail.
Insert the center slide braces into the left slide rail, and then insert the slide into the slide cavity in the left slide rail.
Note: It may take two people to bend the slide and insert it into the slide cavities.
Step 61: Secure the slide assembly with 3" wood screws.
Phase 30: Slide Assembly
W100544 * Slide Brace * 1 ReqW100545 * Slide Brace Center * 2 ReqX15-8YS * Slide * 1 ReqX15-8GL * Slide Rail Left * 1 ReqX15-8GR * Slide Rail Right * 1 Req
Washer Head Bolt * 5/16 x 1/2" * 3 ReqWasher Head Barrel Nut * 5/16 x 5/8" * 3 Req Star Washer * 12 x 19mm * 3 ReqWood Screw * #8 x 3" * 24 Req
1/4"
43Columbia Model 65110 • 09-10-0111
Items needed for this phase: Hardware needed for this phase:
43
Step 62: Position the slide on top of the M2s, and then pre-drill the holes through the slide and the M2s. Attach the slide to the M2s with 1/2" head bolts, star washers, and 5/8" barrel nuts.
Phase 31: Slide Assembly
Washer Head Bolt * 5/16 x 1/2" * 3 ReqWasher Head Barrel Nut * 5/16 x 5/8" * 3 Req Star Washer * 12 x 19mm * 3 Req
M2s
44Columbia Model 65110 • 10-0111
Items needed for this phase: Hardware needed for this phase:
44Columbia Model 65110 • 10-0111
Step 63: Measure in about 3" from the E5s, E2, E4, and the A-frame legs. Mark the ground, and then twist the metal stakes into the ground. Leave 2" of the metal stake above the ground. Note: You may need to use a long screwdriver for leverage.
Step 64: Pre-drill the holes for the stakes with a 5/16" drill bit. Attach the metal stakes to the K1s and A-frame ground board with 1" Phillips truss head bolts, lock washers, barrel nuts, and fl at washers.
Phase 32: Stake Assembly
Y41 * Metal Stake * 6 Req Phillips Truss Head Bolt * 1/4-20 x 1" * 6 ReqBarrel Nut * 1/4x 3/4" * 6 ReqFlat Washer * 9 x 18mm * 6 ReqInternal Tooth Lock Washer * 8 x 15mm * 6 Req
Lock Washer
Phillips Truss HeadBolt
FenderWasher
Phillips Barrel Nut
FenderWasher
E5
E5
E4
E2
K1
45Columbia Model 65110 • 09-10-0111
Items needed for this phase: Hardware needed for this phase:
Step 65: Attach the glider seat to the glider arms with 5-3/4" head bolts, fender washers, and lock washers.Step 66: Loosen 4 quick links, and then insert them into the top of the glider arms. Loosen the swing hanger bolts on the glider supports, and then insert the 38.5" chain link. Tighten
the swing hanger bolts to secure the chain link. Insert the chain into the glider quick links, and then tighten the quick links on the glider.
Step 67: Loosen the swing hanger bolts on the swing beam, and then insert the 51.25" chain. Tighten the swing hanger bolts.
Step 68: Loosen 4 quick links, and then insert them into the tops of the swing seats. Insert the chain link into the quick links, and then tighten the quick links to secure the chain link.
Phase 33: Swing and Glider Assembly
X10-Y * Glider Seat * 1 ReqX10-G * Glider Arm * 2 ReqA100015 * 38.5" * Chain * 4 ReqZQL * Quick Link * 8 ReqY60 * 51.25" * Chain * 4 ReqX2-Y * Swing Seat * 2 Req
Washer Head Bolt * 5/16 x 5-3/4" * 2 ReqFender Washer * 8 x 27mm * 2 Req Lock Nut * 5/16" * 2 Req
Limited Warranty
This Limited Warranty by Backyard Discovery applies to products manufactured under the Backyard Discovery brand or its other brands including but not limited to Backyard Botanical, Adventure Playsets, and Leisure Time Products.
Backyard Discovery warrants that this product is free from defect in materials and workmanship for a period of one (1) year from the original date of purchase. This one (1) year warranty covers all parts including wood, hardware, and accessories. All wood carries a five (5) year pro-rated warranty against rot and decay. Refer to the schedule below for charges associated with replacement of parts under this Limited Warranty. In addition, Backyard Discovery will replace any parts within the first 30 days from date of purchase found to be missing from or damaged in the original packaging.
This warranty applies to the original owner and registrant and is non-transferable. Regular maintenance is required to assure maximum life and performance of this product and failure by the owner to maintain the product according to the maintenance requirements may void this warranty. Maintenance guidelines are provided in the Owner’s Manual.
This Limited Warranty does not cover:
• Labor for any inspection • Labor for replacement of any defective item(s) • Incidental or consequential damages • Cosmetic defects which do not affect performance or integrity of a part or the entire product • Vandalism, improper use, failure due to loading or use beyond the capacities stated in the applicable
Assembly Manual. • Acts of nature including but not limited to wind, storms, hail, floods, excessive water exposure • Improper installation including but not limited to installation on uneven, unlevel, or soft ground • Minor twisting, warping, checking, or any other natural occurring properties of wood that do not affect
performance or integrity
Backyard Discovery products have been designed for safety and quality. Any modifications made to the original product could damage the structural integrity of the unit leading to failure and possible injury. Modification voids any and all warranties and Backyard Discovery assumes no liability for any modified products or consequences resulting from failure of a modified product.
This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a Backyard Discovery product be used in public settings. Such use may lead to product failure and potential injury. Any and all public use will void this warranty. Backyard Discovery disclaims all other representations and warranties of any kind, express or implied.
This Warranty gives you specific legal rights. You may have other rights as well which vary from state to state or province to province. This warranty excludes all consequential damages, however, some states do not allow the limitation or exclusion of consequential damages and therefore this limitation may not apply to you.
Pro Rated Part Replacement Schedule
Product Age Customer Pays All Parts 0-30 days from date of purchase $0 and free shipping 31 days to 1 year $0 + S&H
Wood Rot and Decay Only 1 year $0 and free shipping 2 years 20% + S&H 3 years 40% + S&H 4 years 60% + S&H 5 years 80% + S&H Over 5 years 100% + S&H