cm offshore presentation
TRANSCRIPT
A Short Presentation. A small insight into the
Company activities.
CM Offshore
Some Projects from CM Workforce
Top left Pile sleeve BW IITopRight picture Amplemann Deck for Offshore Transport vessel.Bottom left Central cluster Bard I.Bottom right Repair on Aluminium Boat ( Fred Olsen )
CM Offshore with there QM Handbook
Tries to demonstrate its ability to consistently provide a product that meets customer and applicable statutory and regulatory requirements, and.
Aims to enhance customer satisfaction through the effective application of the system, including processes for continual improvement of the system and the assurance of conformity to customer and applicable statutory and regulatory requirements.
Certification
DIN 18800-7:2008-11
Meeting with company representative for kick off meeting Checking all possible hazards, issues etc. associated with the project
involved Working with full safety requirements Every worker must do initial safety introduction before contract begin Planning of safety meetings during the project Nominating safety representatives for the duration of the contract Look at minimising scaffold requirements, reducing the need for
working at height
HSE Control
WorkshopsHall 25Length: 120 m Width: 23 m Sqm: 2.760 m²
10 ton gantry crane (3 pieces) hook height: 6 mPlasma burning machine Co. Messer „Plasma Multi Therm 4000“One-to-one burning machine Co. Messer „Burny“3-drums rotund bending machine Co. Faccin, type „OP3 3134“Frame bending machine Co. Faccin, type „GNC 400“
CM Offshore and partners
WorkshopsHall 14Length: 50 m Width: 30 m Sqm: 150 m²
35 ton crane hook height: 13,6 m17 ton crane hook height: 14,5 m
CM Offshore and partners
WorkshopsHall 8 (smithery)Length: 32,5 m Width: 18 m Sqm: 585 m²
3,2 ton crane hook height: 5,5 m5,0 ton crane (2 pieces) hook height: 6 mPlate shear Co. Parat, type „GVX-2030“
CM Offshore and partners
WorkshopsHall 8.1 (smithery)Length: 16,5 m Width: 18 m Sqm: 297 m²
Rotund bending machine Co. Schafer KG, type „SRMASY“Turning machine Co. Labor, type „1805“Moulding cutter Co. Wewag, type „Starmill“Band saw Co. Flott, type „HBS 300 H“Bending machine 1 (old) Co. Schröder „fabr. no. 190116“Bending machine 2 (new) Co. Haco, type „PPH 36 135“
CM Offshore and partners
WorkshopsHall 8.2 (press machine)Length: 18 m Width: 18 m Sqm: 324 m²
5 ton crane hook height: 5,5 m3,2 ton crane hook height: 5,5 m1,5 ton crane hook height: 5,5 mShipbuilding press machine Co. Hollmann Werke, type „BSP JVG BSP 22.2.00A01“Plate shear Co. Kramer, type „TMIIIHG 3000“
CM Offshore and partners
Automobiles and trucksTrucks and transporters 4 Mercedes transporters total approved volume: 3,5 ton1 M.A.N. truck total approved volume: 3,35 ton
Forklifters1 forklifter Co. Linde, type „H60 D“ (diesel fuel)1 forklifter Co. Linde, type „H40 D“ (diesel fuel)1 forklifter type „E 16 C“ (electronical)
CM Offshore and partners
Organisation chartDerrick
UnderwoodManaging
Direktor
Paulo Cerqueira
Production Manager
DarioGomez Qualität Manager
HenningBuchin
H S E
Thomas Komoroski
Welding Engineer
Seit Zehn Jahren Erfahrung
Orbital Technik
UP Schweißverfahren
UP SCHWEIßER UND UP MACHINE
Schweißer Und Schweiß naht Qualität
Location, Location, Location.
Barkhausentraße 60 D-27568 BremerhavenGermany
Thank you for your attention