cloradores gamma

24
ProMinent gamma–1 ProMinent ® gamma The gamma/b series is a micropro- cessor-controlled, diaphragm-type, solenoid driven metering pump for low flow applications. The capacity range is 0.05 gph (0.2 L/h) @ 145 psi to the maximum of 8 gph (30.3 L/h) @ 29 psi. PLEASE NOTE: This pump has been replaced by the gamma/L series for most applications. All gamma/b pumps include the timer option as standard except the following models which are not convertible to the gamma/L: gamma/4b 1000, 1001 and gamma/5b 1310 and 0813. The high viscosity models are also available with or without the timer. Available (Standard in Canada) Approved The gamma/b metering pumps are registered according to DIN-VDE 0700 and protected against radio interference class B according to DIN-VDE 0871.

Upload: oxiel-carrizo-pozo

Post on 26-Oct-2014

77 views

Category:

Documents


5 download

TRANSCRIPT

Page 1: Cloradores Gamma

ProM

inen

t

gamma–1

ProMinent® gamma

The gamma/b series is a micropro-cessor-controlled, diaphragm-type,solenoid driven metering pump forlow flow applications. The capacityrange is 0.05 gph (0.2 L/h) @ 145psi to the maximum of 8 gph (30.3L/h) @ 29 psi.

PLEASE NOTE: This pump hasbeen replaced by the gamma/Lseries for most applications. Allgamma/b pumps include the timer

option as standard except thefollowing models which are notconvertible to the gamma/L:gamma/4b 1000, 1001 andgamma/5b 1310 and 0813. Thehigh viscosity models are alsoavailable with or without the timer.

Available(Standardin Canada)

Approved

The gamma/b meteringpumps are registeredaccording to DIN-VDE0700 and protectedagainst radiointerference class Baccording to DIN-VDE0871.

Page 2: Cloradores Gamma

ProM

inen

t

gamma–2

ProMinent® gamma/b series metering pumpsProMinent gamma/4b andgamma/5b metering pumpsfeature identical operation andaccessories.

The electronic control circuit,equipped with 2 microprocessors,enables a tailor-made solution forevery application.

The basic version allows manual orexternal pulse control. Pumpoptions, accept nearly any cus-tomer-specific control signal. Theoperational reliability of the pumpcan be increased by a variety ofmonitoring equipment.

The LCD display is illuminated forvisibility in low light areas andprovides simple and concise userguidance. The LCD also displaysthe actual operating status andwarns the operator of possiblefaults.

The pump housingAttractive, functional constructionof fiberglass-reinforced PPE plastic,the NEMA 4x housing offersmaximum protection againstcorrosion, dust and water.

The solenoid driveThe solenoid drive has only onemoving part, the armature. Thepower end consists of a short-stroke solenoid with a maximumstroke length of 0.05" (1.25 mm),

and is equipped with a noisesuppressing mechanism for quietoperation.

The stroke-length adjustingmechanism is directly connected tothe solenoid. Operation results inan accurate self-locking strokelength setting.

The pump diaphragmThe DEVELOPAN® compositediaphragm consists of high-quality,nylon-fabric reinforced EPDMvulcanized onto a steel core, and isPTFE-faced on the liquid contactsurface for extremely long servicelife. The DEVELOPAN diaphragm ischemically resistant against virtuallyall process fluids, and can be usedover a wide temperature range.

An air gap behind the diaphragm,created by a back plate with weephole, followed by a secondarysafety diaphragm prevents chemi-cal intrusion into the solenoidhousing in the event of maindiaphragm failure.

The liquid endLiquid ends for the gamma/bmetering pump are available in 4standard material versions:

• Polypropylene (PP/PS)• Acrylic/PVC (NP/NS)• PTFE (TT)• 316 Stainless steel (SS)

The suction and discharge portsare equipped with double ballcheck valves for maximum repeat-ability (except high viscositymodels PP4 and PP5, and versions0423 and 0230 with single ballvalves). Versions 1000-0417 PP1,PP2, PP3, and NP1, NP2, NP3,liquid ends provide a coarse bleedvalve for easy priming and a finebleed valve for continuous bleedingof fluids that tend to off-gas toprevent airlock. Automatic gasbleed-off is available with the NS/PS self-degassing liquid ends foreight gamma/4b models.

Special polypropylene liquid ends(PP4 and PP5) are available onversions 1002, 1006, 1310 and0813 for high viscosity fluids.These are equipped with anincreased flow profile and largerspring-loaded single ball valves.

Wide margin of power supply voltageThe gamma/b metering pumpsaccept either 115 or 230 voltpower, single phase, 50/60 Hz, witha 1.15 service factor. Performanceis identical whether operated on50 Hz or 60 Hz power.

Inputmeteringmonitor

Inputtwo-stage

float switch

Powerinput Signal

input(pulse oranalog)

Alarmrelay

output

Page 3: Cloradores Gamma

ProM

inen

t

gamma–3

gamma/b microprocessor control -basic to any process.

THE BASIC VERSION

Note: The capabilities listed onthis page are common to allgamma/b pumps. The cable forexternal pacing or remotepause is an optional accessory,as are the float switch, flowmonitor and relay outputs.

Stroke frequency control

Continuous operation –“Manual”

The pump capacity can be variedvia the stroke length knob (from 0to 100% stroke length), and byvarying the stroking rate via the up/down arrows on the keypad. Seethe Technical Data for a particularmodel's maximum stroking rate,(e.g. 100, 120, or 180 strokes perminute). The selected stroking rateis shown on the LCD display and isperformed with quartz-like accu-racy. The gamma/b manual controlrange permits 1000:1, 1200:1, or1800:1 turndown, depending onmaximum stroke rate. The simu-lated LCD display below showsmanual control with frequency of120 strokes per minute.

External pacing – “Contact”The gamma/b series can be pacedexternally (e.g. by means of apulse-type water meter for propor-tional chemical feed). The pulsesignals are fed into the contactinput of the pump by an optionalcontrol cable. Every pulse from awater meter or pulse-type controllerproduces one pump stroke, up tothe pump's maximum stroke rate.Over-stroking the pump is notpossible. LCD display shows “E”for external contact pacing.

stops, the display flashes “Error”and “Flow” as shown below, andthe red LED lights. The optionalfault relay changes state to issue analarm or activate a standby pump.

Remote pause

Remote on/off control –“Pause”

The gamma/b series can beswitched on or off via a form-C drycontact through the optionalcontrol cable. The pump operateson a closed contact; if the contactis open, the pump stops and thedisplay shows “Pause” and “Stop”.

Problem identification

Auto-fault diagnosis

The electronic control circuit of thegamma/b series monitors itselfcontinuously. Any fault of themicroprocessor stops the pumpand issues an alarm (with faultannunciating relay option). TheLCD readout flashes and the redLED lights.

Lighting

The backlit LCD screen makes thedisplay easy to read, even in poorlylit locations.

Ensure fluid flow

Chemical tank float switch –“Minimum”

An optional two-stage ProMinentfloat switch can be plugged intothe pump to monitor chemicallevels in the source tank. An earlywarning will be issued when theallowable minimum level isreached. The pump continues tooperate while the display flashes“Minimum," a red LED lights andan optional collective fault relaychanges state to issue an alarm. Ifthe liquid level in the supply tankdrops another 3/4" (20 mm), thepump automatically shuts downand the LCD displays “Error” and“Minimum” as shown below. Theoptional fault relay remainsactivated.

Flow monitor – “Flow”

The gamma/b series meteringpumps will monitor their ownoutput, with the optional adjustableflow monitor connected to thedischarge valve and plugged intothe front of the pump. (Note: onsizes 0423 and 0230, the flowmonitor must be mounted on adischarge bypass line). Every fluiddischarge is sensed and fed backto the electronic control circuit ofthe pump. If insufficient fluid isdischarged for 8 consecutivestrokes, the pump automatically

Contact

E

120Manual

f

120Pause Stop

Manual

f

120Error

Manual flow

120Error

MinimumManual

f

Page 4: Cloradores Gamma

ProM

inen

t

gamma–4

CONTROL VERSIONSAND OPTIONS

Control versions and optionscan be selected to suit yoursystem's specific needs.

Analog control

With this option, the stroking rate ofthe gamma/b is directly propor-tional to the analog signal. Themaximum number of strokes perminute corresponding to the analogsignal range can be selected by theoperator. Input signals can bespecified when ordering with the“Identity code” (e.g. 0-20 mA, 4-20mA, 0-60 mV, 0-1 V, 0-10 V).Inverse analog (20-4 mA/20-0 mA)is also available.

Pulse multiplier/divider

This feature is used to “tune” thegamma/b to contact generators ofany kind (e.g. pulse-type watermeter or process controller), andeliminate the need for a costlyexternal control unit. The followingfunctions can be selected bymeans of the keypad.

Pulse step-up (multiply) andstep-down (divide)

By simply entering a factor in the0.01-9999 range, the step-up orstep-down ratio is set.

For example:

Step-up Factor:9999 1 pulse = 9999 pump strokes10 1 pulse = 10 pump strokes

Step-down Factor:0.25 4 pulses = 1 pump stroke0.01 100 pulses = 1 pump stroke

Customize the gamma/b.You select the control versions and options required.

Predetermining counter –“N ↔↔↔↔↔”

The pulse multiplier/divider featureis used as a predetermining counterfor batch applications. Up to 9999strokes can be predetermined. TheLCD screen displays the number ofstrokes yet to be completed. Thecountdown starts by a voltage-freecontact on the optional externalcontrol cable or by pressing the “P”key. Larger batches up to 65,535strokes are also possible; forexample, 59,994 strokes may beperformed by providing six contacts(6 x 9999) in memory mode.

Memory – “Mem.”

Should the pump receive contactsignals faster than the selectedstroking rate, these pulses can bestored in the gamma's memory (toa maximum limit of 65,535) andworked off at the preset strokingrate.

Stroke counter – “N”

This feature totalizes pump strokesthat have been performed. Thecounter resets itself to 1 and acursor appears on the LCD screenwhen 9999 strokes have beenaccumulated. This totalizer can beused in manual, contact, and analogmodes.

Timer

The optional integrated timerfunction allows up to 31 variableon-off times to be programmeddaily, or over the course of a 7-dayperiod. The “on-time” can beselected between 1 minute and 24hours. Typical applications includetime feeding of biocides for coolingtowers, brewery pasteurizers, etc.The timer can be used in conjunc-tion with manual, contact or analogcontrols such that those functions

120 f

Analog

0.25 Contact

f

only operate when the timer isactivated. The screen below showsthe time as 12:00 p.m. on a 24-hourclock.

RS Interface

Gamma/4b with serial interface RS232 or RS 485 for external com-puter control is available. ContactProMinent for compatibility withcomputer hardware/software.

Relay outputs. . .are employed to transmit alarmmessages, to start a back-uppump, indicate pump status, or topace a second ProMinent meteringpump synchronously. Selectableas:

Fault annunciating relayFor low tank level (flow switch), lossof flow (flow monitor), system faultsand fuse/power supply failure.Function: relay drops out with analarm.

Paclng relayA contact closure is issued withevery pump stroke (contactduration 150 ms). This allows asecond ProMinent metering pumpto be paced synchronously, or tototalize flow with an external strokecounter.

Alarm relayFor low tank level (flow switch), lossof flow (flow monitor) and systemfaults. Function: relay pulls inwhen an alarm condition exists.

Timer relayFunction: relay pulls in to indicatewhen the pump is running. Onlyavailable with 7-day timer.

20.00Mem N ↔↔↔↔↔Contact

Manual

12:00

Page 5: Cloradores Gamma

ProM

inen

t

gamma–5

Auto-Degassing gamma/4b Pumps

The only choice for pumpingfluids that out-gas.

Many fluids, such as sodiumhypochlorite or hydrogen peroxide,out-gas as they are drawn into thesuction line of a metering pump orif the pump sits idle for a length oftime. The gas accumulates in theliquid end and is compressed witheach discharge stroke, causing airlock and loss of flow.

A special bleed valve in thegamma/4 auto-degassing pumpopens at low pressure to allow thegas to be evacuated on eachdischarge stroke. It closes at highpressure, as when fluid is present,causing the fluid to be dischargedthrough the pump's dischargevalve.

This allows the gamma pump toself-prime against its ratedbackpressure and eliminates theneed to relieve pressure on thedischarge line to reprime. Thisfeature is commonly used for drum-mounted pumps, allowing thepump to continue operation whilethe suction line is pulled out of onedrum and dropped into another.

Identity codes for material optionsare NS2 (Acrylic/PVC/EPDM), NS3(Acrylic/PVC/Viton®) and ES1 (PP/EPDM), ES3 (PP/Viton®). Sizes

DischargeConnector

DegassingValve

DischargeValve

SuctionValve Degassing

Connector(back to tank)

include 1601, 1201, 0803 and 1002(120 spm) and 1602, 1203, 0806and 1003 (180 spm).

The best installation utilizes asuction lift, with the pump mountedabove or on top of the chemical

tank, and the air bleed line dis-charging back down to the tankabove the fluid. Flooded suctionapplications with up to 6.5 ft. (2 m)of static suction head are possibleif the air bleed line discharges backto the tank.

Technical Data

Pump Capacity at Maximum Max. DischargeVersion Backpressure Stroking Connectors Suction ShippingNS2/NS3 U.S. ml/ Rate O.D. x l.D. Lift WeightES1/ES3 psig (bar) GPH (l/h) stroke spm inches ft. (m) Ibs. (kg)

g/4b1601 232 (16) 0.17 (0.66) 0.090 120 1/4 x 3/16 5.9 (1.8) 6.8 (3.1)1602 232 (16) 0.26 (0.99) 0.090 180 1/4 x 3/16 5.9 (1.8) 6.8 (3.1)1201 174 (12) 0.26 (1.00) 0.140 120 1/4 x 3/16 6.6 (2.0) 6.8 (3.1)1203 174 (12) 0.40 (1.50) 0.140 180 1/4 x 3/16 6.6 (2.0) 6.8 (3.1)0803 116 (8) 0.63 (2.40) 0.330 120 1/4 x 3/16 9.2 (2.8) 6.8 (3.1)0806 116 (8) 0.95 (3.60) 0.330 180 1/4 x 3/16 9.2 (2.8) 6.8 (3.1)1002 145 (10) 0.48 (1.80) 0.250 120 1/4 x 3/16 6.6 (2.0) 6.8 (3.1)1003 145 (10) 0.71 (2.70) 0.250 180 1/4 x 3/16 6.6 (2.0) 6.8 (3.1)

StandardSuction/

Page 6: Cloradores Gamma

ProM

inen

t

gamma–6

Technical Data: gamma/4b, gamma/5bStandard Suction/ Pre- Shipplng

Pump Capacity at Maximum Capacity at 1/2 Maximum Maximum Discharge Primed Weightversion Backpressure Backpressure Stroking Connectors*** Suction (higher weights

U.S. ml/ U.S. ml/ Rate** O.D. x l.D. Lift are for SS)psig (bar) GPH (L/h) stroke psig (bar) GPH (L/h) stroke spm inches ft. (m) Ibs. (kg)

g/4b1000 145 (10) 0.05 (0.20) 0.027 73 (5) 0.07 (0.27) 0.038 120 1/4 x 3/16 4.9 (1.5) 6.0-7.1 (2.7-3.4)1001 145 (10) 0.09 (0.30) 0.027 73 (5) 0.11 (0.42) 0.038 180 1/4 x 3/16 4.9 (1.5) 6.0-7.1 (2.7-3.4)1601* 250 (17) 0.26 (1.00) 0.14 125 (8.5) 0.32 (1.2) 0.17 120 1/4 x 3/16 19.7 (6) 6.0-7.1 (2.7-3.4)1602* 250 (17) 0.40 (1.5) 0.14 125 (8.5) 0.48 (1.8) 0.17 180 1/4 x 3/16 19.7 (6) 6.0-7.1 (2.7-3.4)1201* 174 (12) 0.45 (1.7) 0.24 87 (6) 0.50 (1.9) 0.27 120 1/4 x 3/16 19.7 (6) 6.0-7.1 (2.7-3.4)1203* 174 (12) 0.66 (2.5) 0.24 87 (6) 0.77 (2.9) 0.27 180 1/4 x 3/16 19.7 (6) 6.0-7.1 (2.7-3.4)0803* 116 (8) 0.90 (3.4) 0.48 58 (4) 1.00 (3.8) 0.53 120 1/4 x 3/16 9.8 (3) 6.0-7.1 (2.7-3.4)0806* 116 (8) 1.40 (5.3) 0.48 58 (4) 1.48 (5.6) 0.53 180 1/4 x 3/16 9.8 (3) 6.0-7.1 (2.7-3.4)1002* 145 (10) 0.61 (2.3) 0.32 73 (5) 0.69 (2.6) 0.36 120 1/2 x 3/8 19.7 (6) 6.2-7.9 (2.9-4.1)1003* 145 (10) 0.90 (3.4) 0.31 73 (5) 0.98 (3.7) 0.34 180 1/2 x 3/8 19.7 (6) 6.2-7.9 (2.9-4.1)0308 43.5 (3) 2.22 (8.40) 1.17 21 (1.5) 2.40 (9.1) 1.27 120 1/2 x 3/8 19.7 (6) 6.2-7.9 (2.9-4.1)0313 43.5 (3) 3.43 (13.0) 1.20 21 (1.5) 4.09 (15.5) 1.43 180 1/2 x 3/8 19.7 (6) 6.2-7.9 (2.9-4.1)0215 21 (1.5) 3.91 (14.8) 2.05 14 (1) 4.20 (15.8) 2.20 120 1/2 x 3/8 4.9 (1.5) 6.8-10.4 (3.1-4.7)0223 21 (1.5) 6.08 (23.0) 2.13 14 (1) 6.74 (25.5) 2.36 180 1/2 x 3/8 4.9 (1.5) 6.8-10.4 (3.1-4.7)g/5b1602 232 (16) 0.61 (2.30) 0.32 116 (8) 0.67 (2.6) 0.36 120 1/2 x 3/8 19.7 (6) 11-13 (4.6-5.8)1605 232 (16) 1.25 (4.74) 0.79 116 (8) 1.5 (5.8) 0.96 100 1/2 x 3/8 19.7 (6) 15-18 (6.7-7.9)1006 145 (10) 1.5 (5.83) 0.81 73 (5) 1.9 (7.1) 0.98 120 1/2 x 3/8 19.7 (6) 11-13 (4.6-5.8)1310 188 (13) 2.5 (9.54) 1.59 87 (6) 2.8 (10.8) 1.80 100 1/2 x 3/8 19.7 (6) 15-19 (6.9-8.5)0613 87 (6) 3.4 (13.1) 1.82 44 (3) 3.9 (14.9) 2.08 120 1/2 x 3/8 18.0 (5.5) 11-15 (4.8-6.4)0813 116 (8) 3.5 (13.3) 2.21 58 (4) 3.8 (14.6) 2.44 100 1/2 x 3/8 19.7 (6) 16-19 (6.9-8.5)0417 50 (3.5) 4.6 (17.4) 2.42 29 (2) 4.7 (17.9) 2.48 120 1/2 x 3/8 14.8 (4.5) 11-15 (4.8-6.4)√0423 50 (3.5) 6.3 (24.0) 4.00 29 (2) 6.5 (24.6) 4.10 100 1/2 MNPT 16.4 (5) 18-25 (8.0-11.4)√0230 29 (2) 8.0 (30.3) 4.21 14 (1) 9.1 (34.5) 4.80 120 1/2 MNPT 8.2 (2.5) 13-20 (5.9-9.3)

PP4 and PP5 gamma metering pumps are for high viscosity fluids.√Not equipped with bleed valves - DN 10 connectiong/4b (DN 10 valve size) MNPT Hose barb1002 145 (10) 0.45 (1.72) 0.24 73 (5) 0.66 (2.5) 0.34 120 1/2 5/8" † 6.2 (3.2)

g/5b (DN 15 valve size)1006 145 (10) 1.5 (5.8) 0.81 73 (5) 1.9 (7.1) 0.98 120 1/2 5/8" † 12 (5.1)1310 145 (10) 2.5 (9.5) 1.59 73 (5) 2.8 (10.8) 1.80 100 1/2 5/8" † 17 (7.4)0813 116 (8) 3.5 (13.3) 2.21 58 (4) 3.8 (14.6) 2.44 100 1/2 5/8 " † 17 (7.4)

* For NS2/NS3 and ES1/ES3 models capacities, consult page gamma-5 for rated capacities (derated from standard liquid ends).** 180 spm pumps are recommended for water-like fluids only.***For SS2 pump heads, 1/4" FNPT fittings are standard; SS1 (0423 and 0230) are 3/8" FNPT.† Positive suction recommended.Above capacities and suction lift refer to pumps tested on water at 115 VAC, 60 Hz, and an ambient temperature of 70°F (20°C).Higher specific gravity fluids will reduce suction lift. Higher viscosity fluids will reduce capacity.

Capacity at maximum pressure on all pumps is tested prior to shipment.

Liquid end materialsPump head Suction/Discharge valves Seals Valve balls Valve balls Features

PP1* Polypropylene Polypropylene EPDM Ceramic Duran Bleed valve

PP2* Polypropylene Polypropylene Viton® Ceramic Duran Bleed valvePP3* Polypropylene Polypropylene Viton® Ceramic - Bleed valvePP4 Polypropylene Polypropylene EPDM Ceramic - High viscosity w/springsPP5 Polypropylene Polypropylene Viton® Ceramic - High viscosity w/springsNP1* Acrylic PVC Viton® Ceramic Duran Bleed valveNP2* Acrylic PVC EPDM Ceramic Duran Bleed valveNP3* Acrylic PVC Viton® Ceramic - Bleed valveNS2*† Acrylic PVC EPDM Ceramic - Auto degassing valveNS3*† Acrylic PVC Viton® Ceramic - Auto degassing valveES1*† PP PP EPDM Ceramic - Auto degassing valveES3*† PP PP Viton® Ceramic - Auto degassing valveTT1 Carbon-loaded PTFE Carbon-loaded PTFE PTFE Ceramic CeramicSS1, SS2 316 Stainless steel 316 Stainless steel PTFE Ceramic Mat. No. 1.4401 (DN standard)

* Standard - injection valves, foot valves, tubing included with pump.† with Hastelloy C valve springs, PVDF valve core.Acrylic (NP), Viton® and Duran (laboratory glass) are registered trademarks.

0423/0230

Page 7: Cloradores Gamma

ProM

inen

t

gamma–7

Switching mode relay:0 Without relay1 Fault annunciating relay, drops out2 Pacing relay, pulls in3 Alarm relay, pulls in4 Timer relay, pulls in

(Note: Cannot be used if RS interface is selected.)

7 Day, 31 event timer/RS interface:0 Without timer or RS interface1 With timer (Standard on all models except, 1000/1001, 1310, 0813,

1002 PP4/PP5 and 1006 PP4/PP5)

Identity code: gamma/b metering pumpsSeries:

g/4b gamma/ 4 version bg/5b gamma/ 5 version b

G/4b G/4b G/5b Pump version:(120 strokes) (180 strokes)1000 1001 1602* 0813 *available in NP and SS only, 1310 also available in PP4/PP51601 1602 1605* 04171201 1203 1006 04230803 0806 1310* 02301002 1003 06130308 03130215 0223

Liquid end materials: Consult the "Liquid End Options" table for liquid ends available on selected pump version.PP1 Polypropylene/EPDMPP2 Polypropylene/Viton®

PP3 Polypropylene/Viton®

PP4 Polypropylene/EPDM high viscosity 1 psig Hast. C valve springsPP5 Same as PP4 but Viton® O-ringsNP1 Acrylic/PVC Viton®

NP2 Acrylic/PVC/EPDMNP3 Acrylic/PVC/Viton®

TT1 PTFE/PTFESS1 316 SS/PTFE 3/8" FNPTSS2 316 SS/PTFE 1/4" FNPTNS2 Auto-degassing Acrylic/EPDM/PVCNS3 Auto-degassing Acrylic/Viton®/PVCES1 Auto-degassing PP/EPDMES3 Auto-degassing PP/Viton®

g/4b 1000 PP1 0 0 0 D 2 0 0 0 0

Valve springs:0 Without springs1 With 2 springs (1 psig) (1/4" valves: 316 SS; 1/2" valves: Hast. C)

Connector:0 Standard according to technical data6 1/2" x 3/8" tubing

Transparent, hinged dust cover version:0 Standard, without lock, with logo1 With lock, with logo (not for gamma 5)2 Without lock, without logo3 With lock, without logo

Electrical connection: (With 6 ft. (2 m) power cord single phase)A 230 V 50/60 Hz Euro plugD 115 V 50/60 Hz N. American plugU 230 V 50/60 Hz N. American plug

(6-15 P NEMA configuration)

Control type: (Note: May be ordered without illumination upon request.)2 Standard with LCD illumination

Control version:0 Manual + pulse (1:1) + remote pause1 0 - 20 mA and 4 - 20 mA2 0 - 60mV / 0 - 1V / 0 - 10V3 20 - 0 mA and 20 - 4 mA

Pulse multiplier/divider:0 Without pulse control1 With pulse control

NOTE: Control versions 1, 2 and 3 (analoginput) include features of control version 0.

NOTE: Connector option 6 must be used on all pumps with standard 1/2" x 3/8"tubing connections, and it may be used on pumps with 1/4" x 3/16" tubingconnectors. Use option 0 on all pumps with standard NPT connections.

Viton® is a registered trademark of DuPont Dow Elastomers

Page 8: Cloradores Gamma

ProM

inen

t

gamma–8

*These models include accessory kits (foot valve, injection valve, tubing). Accessories are ordered separately on PP4, PP5, TT1, SS1 & SS2.

Note: Valve sizes DN10 & DN15 (normally supplied with 1/2" MNPT & 3/4" MNPT respectively) can be supplied with 5/8" & 3/4" hose barb(respectively).

gamma/b Liquid End Options

Type Size PP1* PP2* PP3* PP4 PP5 NP1* NP2* NP3* NS2* NS3* ES1* ES3* TT1 SS1 SS2

g/4b 1000/01 4.7 √ √ √ √ √ √g/4b 1601/02 4.7 √ √ √ √ √ √ √ √ √ √g/4b 1201/03 4.7 √ √ √ √ √ √ √ √ √ √g/4b 0803/06 4.7 √ √ √ √ √ √ √ √ √ √g/4b 1002/03 4.7 √ √ DN10 DN10 √ √ √ √ √ √ √ √g/4b 0308/13 9.2 √ √ √ √ √ √g/4b 0215/23 9.2 √ √ √ √ √ √

g/5b 1602 4.7 √ √ √g/5b 1605 9.2 √ √ √g/5b 1006 9.2 √ √ DN15 DN15 √ √ √ √g/5b 1310 9.2 DN15 DN15 √ √ √g/5b 0613 9.2 √ √ √ √ √ √g/5b 0813 9.2 √ √ DN15 DN15 √ √ √ √g/5b 0417 9.2 √ √ √ √ √ √g/5b 0423 DN10 √ √ √ √ √ √g/5b 0230 DN10 √ √ √ √ √ √

Valve

Liquid end options: gamma/b

Page 9: Cloradores Gamma

ProM

inen

t

gamma–9

Specifications: gamma/bMaximum stroke length: 0.05" (1.25 mm) [except 0.026" (0.65 mm) on pump version 1000]

Materials of constructionHousing: Glass-filled Luranyltm (PPE)

Diaphragm: PTFE faced EPDM with steel core and Nylon reinforcement

Liquid end options: Polypropylene, Acrylic/PVC, PTFE, 316 SS

Enclosure rating: NEMA 4X (IP 65), transparent front cover standard

Insulation class: F

Check valves: Double ball (except single ball on PP4, PP5 models and all version 0423and 0230 pumps)

Standard production test: Capacity at maximum pressure on all pumps is tested prior to ship-ment.

Capacity test criteria: -5% to +15%

Repeatability of the metering: When used according to the operating instructions ±2%

Power cord: 6 foot (2 m) 2 wire + ground

Relay cable (optional): 6 foot (2 m) 3 wire (SPDT)

Relay load: 250 V / 2 A

Ambient temperature range: 14°F (-10°C) to 113°F (45°C)

Max. fluid operating temperatures: Material Constant Short TermAcrylic/PVC 113°F (45°C) 140°F (60°C)Polypropylene 122°F (50°C) 212°F (100°C)PTFE 122°F (50°C) 248°F (120°C)316 SS 122°F (50°C) 248°F (120°C)

Average power drain at maximumstroking rate (Watts) / peak current

drain at pump stroke (Amps)g/4b: 115 VAC, 50/60 Hz: 16W/1.5A (120 spm models); 24W/1.5A (180 spm)

230 VAC, 50/60 Hz: 25W/0.9A (120 spm models); 38W/0.9A (180 spm)g/5b: 115 VAC, 50/60 Hz: 47W/4.1A (120 spm models), 65W/6.7A (100 spm)

230 VAC, 50/60 Hz: 61W/2.1A (120 spm models), 83W/3.1A (100 spm)

Remote pause and/or Contact inputVoltage level with open contact: Approximately +5 VDC supply voltage

Impedance: 10 kOhm

Pulse Contact/ With form-C dry contact, or with semiconductor sink logic control (NPN),Remote Pause Contact: not source logic (PNP). With a residual voltage of <700 mV, the contact

load is approximately 0.5 mA at +5 VDC. (Note: Semiconductor contactsthat require >700 mV across a closed contact should not be used).

Max. pulse input frequency: 40 pulses/sec

Max. pulse memory: 65,535 pulses

Necessary pulse contact duration: 20 ms

Analog - Current input burden: Approximately 70 Ohm

Max. allowable input current: 50 mA

Service factor: 1.15 (98-132 VAC or 195 to 264 VAC)Note: performance is the same on 50 or 60 Hz power

Warranty: Two years on drive, one year on liquid end

Industry standards: CSA (available standard in Canada); CE (approved)

Max. solids size in fluid: Pumps with 1/4" valves: 15µ - Pumps with 1/2" valves: 50µValve threads: 4 NP, PP and TT (except PP4/PP5 and 0423/0230); M20 x 1.5 (tubing

adapter supplied)4 NP, PP and TT 0423/0230, and g/4a 1002 PP4/PP5; DN10 (1/2" MNPT adapter supplied)4 PP4/PP5 1006, 1310 and 0813; DN15 (1/2" MNPT adapter supplied)4 SS (except 0423/0230); 1/4" FNPT4 SS 0423/0230; 3/8" FNPT

Page 10: Cloradores Gamma

ProM

inen

t

gamma–10

gamma/4b A B C D E F G1000/1001 PP 9.1 (232) 7.3 (186) 0.7 (17) 2.8 (70) 1/4 x 3/16 3.2 (81) 1.5 (38)1601/1602 NP 9.1 (230) 7.0 (179) 0.7 (19) 2.8 (70) 1/4 x 3/16 3.2 (81) 1.5 (38)1201/1203 TT 8.4 (213) 6.8 (173) 1.0 (25) 2.4 (60) 1/4 x 3/16 3.1 (79) 1.5 (38)

SS 8.3 (211) 6.5 (164) 1.3 (34) 2.4 (60) 1/4 FNPT 3.1 (79) 1.5 (38)0803/0806 PP 9.1 (232) 7.3 (186) 0.7 (17) 2.8 (70) 1/4 x 3/16 3.2 (81) 1.5 (38)

NP 9.1 (230) 7.0 (179) 0.7 (19) 2.8 (70) 1/4 x 3/16 3.2 (81) 1.5 (38)TT 8.4 (213) 7.0 (178) 0.8 (20) 2.8 (70) 1/4 x 3/16 3.1 (79) 1.5 (38)SS 8.3 (211) 6.7 (169) 1.1 (29) 2.8 (70) 1/4 FNPT 3.1 (79) 1.5 (38)

1002/1003 PP 8.9 (225) 7.3 (186) 0.7 (17) 2.8 (70) 1/2 x 3/8 3.0 (76) 2.0 (50)0308/0313 NP 8.8 (223) 7.4 (187) 0.4 (11) 3.3 (85) 1/2 x 3/8 3.0 (76) 2.0 (50)

TT 8.5 (216) 8.1 (206) 0.3 (8)* 3.1 (80) 1/2 x 3/8 3.1 (79) 2.0 (50)SS 8.4 (214) 8.1 (206) 0.3 (8)* 3.1 (80) 1/4 FNPT 3.0 (77) 2.0 (50)

0215/0223 PP 8.9 (225) 7.8 (197) 0.2 (6) 3.5 (90) 1/2 x 3/8 3.0 (76) 2.6 (66)NP 8.8 (223) 7.7 (195) 0.1 (3) 3.9 (100) 1/2 x 3/8 3.0 (76) 2.6 (66)TT 8.5 (216) 8.4 (214) 0.6 (16)* 3.7 (95) 1/2 x 3/8 3.1 (79) 2.6 (66)SS 8.4 (214) 8.2 (209) 0.4 (11)* 3.7 (95) 1/4 FNPT 3.0 (77) 2.6 (66)

1002 PP4/5 8.4 (214) 6.8 (172) 0.2 (4)* 2.8 (70) 1/2 MNPT 2.4 (60) 2.0 (50)1601/1602 NS/ES 8.8 (224) 7.6 (192.5) 0.7 (17.5) 3.2 (81) 1/4 x 3/16 3.3 (83) 1.5 (38)1201/12030803/08061002/1003 NS/ES 8.8 (224) 7.6 (192.5) 0.7 (17.5) 3.2 (81) 1/4 x 3/16 3.3 (83) 2.0 (50)

gamma/5b

1602, 1605, 1006 PP 10.5 (267.5) 8.1 (207) 1.5 (38) 2.8 (70) 1/2 x 3/8 3.6 (92.5) 2.0 (50)NP 10.5 (267.5) 8.1 (207.5) 1.3 (32.5) 3.3 (85) 1/2 x 3/8 3.6 (92.5) 2.0 (50)TT 10.1 (257.5) 9.0 (227.5) 0.5 (13) 3.1 (79.5) 1/2 x 3/8 3.7 (94.5) 2.0 (50)SS 10.1 (257.5) 8.7 (220) 0.8 (19.5) 3.1 (79.5) 1/4 FNPT 3.7 (94.5) 2.0 (50)

a) 1310, 0613 PP 10.5 (267) 8.3 (212) 1.1 (28) 3.5 (90) 1/2 x 3/8 3.7 (93) 2.6 (66)NP 10.5 (267) 8.5 (215) 1.0 (25) 3.9 (100) 1/2 x 3/8 3.7 (93) 2.6 (66)

b) 0813, 0417 TT 10.2 (258) 9.3 (237) 0.1 (3.5) 3.7 (94.5) 1/2 x 3/8 3.7 (95) 2.6 (66)SS 10.2 (258) 9.0 (230) 0.4 (10.5) 3.7 (94.5) 1/4 FNPT 3.7 (95) 2.6 (66)

0423, 0230 PP 10.1 (257.5) 10.8 (275) 0.7 (17.5)* 5.3 (135) 1/2 MNPT 3.7 (94.5) 4.6 (117)NP 10.1 (257.5) 10.8 (275) 0.7 (17.5)* 5.3 (135) 1/2 MNPT 3.7 (94.5) 4.6 (117)TT 10.1 (257.5) 9.2 (233.5) 0.7 (17.5)* 5.3 (135) 1/2 MNPT 3.7 (94.5) 4.6 (117)SS 10.1 (257.5) 9.2 (233.5) 0.3 (6.5) 5.3 (135) 3/8 FNPT 3.7 (94.5) 4.6 (117)

1006 PP4/5 10.5 (269) 7.6 (193) 1.9 (47) 3.3 (85) 1/2 MNPT 4.1 (103) 2.0 (50)1310 PP4/5 10.6 (270) 7.6 (193) 1.9 (47) 3.3 (85) 1/2 MNPT 4.1 (104) 2.6 (66)0813 PP4/5 10.5 (269) 7.9 (200) 1.6 (40) 3.9 (100) 1/2 MNPT 4.1 (104) 2.6 (66)

Dimensions: gamma/4b, gamma/5b

* This dimension extends below the pump baseline by the value shown.

** Bleed valve and bypass available on sizes 1000 through 0417 PP and NP only; not available on PP4/5 liquid ends.

Dimensions are in inches, rounded to nearest 1/10". Dimensions within brackets ( ) are in millimeters.

A

6.2 (158) g/4b

7.8 (197) g/5b

4.7 (119) g/4b

5.7 (145) g/5b

2.8 (70) g/4b3.4 (87) g/5b

∅ 0.2 (5.1) g/4b∅ 0.25 (6.4) g/5b

F

C

3.9

(99)

g/4

b

4.7

(120

) g/

5b

∅ 0.16 (4)** B

0.5 (13)**

3.1 (80) g/4b

3.9 (100) g/5b

3.5 (90) g/4b

4.4 (112) g/5b

∅ G

∅ E

7.5

(190

)∅ D

3.5 (90) g/4b

4.9 (124) g/5b

Type NS/ES

I

G3.1 (80)3.5 (90)

H

5.7

(146

)

Page 11: Cloradores Gamma

ProM

inen

t

gamma–11

Description Part No.

Accessory kits

PP1, PP2, PP3, NP1, NP2, NP3, NS2, NS3, ES1, ES3 pumps include tubing (except versions 0423 & 0230), foot valveand injection valve as standard.

Accessory kits for gamma pumps with tube fittings, including 5 ft. (1.5 m) of suction tubing,10 ft. (3 m) of discharge tubing, foot valve and injection valve.

Tubing Size (in.) Material Suction Discharge(select to fit pump) Code Tubing Tubing

1/4 x 3/16 NP1/NP3/NS3/ES3 PE PE 78094011/4 x 3/16 PP1 PE PE 78094031/4 x 3/16 PP3 PE PE 78094051/4 x 3/16 NP2/NS2/ES1 PE PE 7809422

1/2 x 3/8 NP1/NP3 PVC PE 78094021/2 x 3/8 PP1 PVC PE 78094041/2 x 3/8 PP2 PVC PE 7809406

Note: The NS3 accessory kits include an additional 5 ft. (1.5 m) of tubing.PVC 1/2" x 3/8" suction tubing is pliable, allowing foot valve to sink. PE discharge tubing is rigid.Pressure ratings are:

PVC: 7 psig PE: 100 psig.

Accessory kits for pumps with NPT fittings (0423, 0230). These kits include foot valveand injection valve with 1/2" MNPT connection ports, but do not include tubing.

MaterialMaterial Code

PVC/Viton® NP1 7809411PVC/EPDM NP2 7809424PP/EPDM PP1 7809412PP/Viton® PP2 7809413

Tubing, foot valves and injection valves for TT and SS pumps are not available as kits andmust be ordered as separate items.

ProMinent® gamma/bAccessory kits

Page 12: Cloradores Gamma

ProM

inen

t

gamma–12

ProMinent® gamma/bControl cablesDescription Part No.

Universal control cable

For metering pump control via contact closure (pulse), standard process signal (analog),and voltage-free contact for remote pause control.

For gamma/b and gamma/a with 5-pole round plastic connector and 5-wire cable with loose end.

Universal control cable, 5-pole round connector, 5-wire, 6 ft. (2 m) 1001300Universal control cable, 5-pole round connector, 5-wire, 16.4 ft. (5 m) 1001301Universal control cable, 5-pole round connector, 5-wire, 32.8 ft. (10 m) 1001302

External control cables for gamma/b

ON/OFF Control

BROWN and BLACK wires must be connected together via an ON/OFF contact or shorted together. When the contactis closed between the BLACK & BROWN wires, the pump will run. When the contact is open, the pump will stop.

Note: If ON/OFF control is the only control feature being used, WHITE, BLUE & GREY wires are not used and should becut.

Pulse Control

Pulse control will allow the pump to run in proportion off of a pulsing potentially free contact closure.

Note: BROWN and BLACK wires have to be connected together via an ON/OFF contact or shorted together. GREYwire is not used and should be cut.

Analog Control

Analog control runs in proportion to an analog signal such as 4 - 20 mA.

Note: BROWN and BLACK wires must be connected together via an ON/OFF contact or shorted together. The BLACKwire is negative and the BLUE wire is positive. GREY wire is not used and should be cut.

BROWN: Remote On/Off (+)

BLACK: Common

GREY: Not used

WHITE: Pulse (+)

BLUE: Analog (+)

BROWN: Remote On/Off (+)

BLACK: Common

GREY: Not used

WHITE: Pulse (+)

BLUE: Analog (+)

BROWN: Remote On/Off (+)

BLACK: Common

GREY: Not used

WHITE: Pulse (+)

BLUE: Analog (+)

Page 13: Cloradores Gamma

ProM

inen

t

gamma–13

ProMinent® gamma/bMetering monitorDescription Part No.

Metering monitor

Adjustable metering monitor “Flow Control”For gamma/b and with signal transmitter and connecting cable with 4-pole round connector for direct connection withthe metering pump.

For monitoring the actual flow output per pump stroke using a plastic encapsulated metal poppet detected by theadjustable proximity sensor. A red LED flashes with each monitored stroke. If there is no flow monitored for eightstrokes, the metering pump is shut down and an alarm signal is issued via optional fault relay on pump. Assembledirectly on the discharge connector of the pump; plug cable into 4-pole round socket on pump. Materials: PP or PVC.Enclosure rating: NEMA 4X (IP 65). Maximum operating pressure is 232 psig (16 bar).

Threads are M20 x 1.5 Female on inlet side for mounting directly onpump discharge valve, and M20 x 1.5 Male on discharge side forthe standard tubing connector that comes with the pump.

Metering monitor for PP/NP/TT version pumps: (FIG. 1)Flow Control type I PP, EPDM, m20 x 1.5 792076Flow Control type II PP, EPDM, m20 x 1.5 792077Flow Control type III PP, EPDM, m20 x 1.5 792078

Flow Control type I PVC, Viton®, m20 x 1.5 792073Flow Control type II PVC, Viton®, m20 x 1.5 792074Flow Control type III PVC, Viton®, m20 x 1.5 792075

Type I = g/4 1601, 1602, 1201, 1203, 0803, 0806, 1002, 1003; g/5 1602

Type II = g/4 0308, 0313; g/5 1605, 1006, 1310

Type III = g/4 0215, 0223; g/5 0613, 0813, 0417, 0423, 0230

Note: On models 0230 and 0423, monitor should be mounted on abypass (as shown below), which will require adapters listed below.Note: Must mount the flow monitor vertically on the pump.

Bypass Assemblies with Metering monitor for version 0423/0230:PVC, Viton®, 1/2" FNPT inlet and discharge 7358655PP, EPDM, (PVDF bypass), 1/2" FNPT inlet and discharge 7740709

Pump

Flow monitor Max. flow through bypass: 2.5 ml/stroke

Control Valve

(For use with low-viscosity (water-like) fluids only).

FIG. 1

Adapter set to connect metering monitor for SS version pumpsAdapter with seals, for use with SS2 liquidends: 1/4" MNPT x Male M20 x 1.5 adapter, PVDF 7358651

Adapter with seals, for use with SS2 liquid 7358659ends: 3/8" MNPT x Male M20 x 1.5 adapter, PVDF

Page 14: Cloradores Gamma

ProM

inen

t

gamma–14

ProMinent® gamma/b (new style)Spare PartsSpare parts and Liquid ends

Complete liquid ends include pump head, valves, mounting screws, diaphragm and backplate. Spare parts kits include:

PP, NP & NELiquid Ends TT Liquid Ends SS Liquid Ends NS & ES Liquid Ends

1 Diaphragm 1 Diaphragm 1 Diaphragm 1 Diaphragm1 Suction Valve 1 Suction Valve 4 Valve Balls 1 Suction Valve1 Discharge Valve 1 Discharge Valve 1 Discharge Valve Inserts 1 Discharge Valve2 Adapter Sets 2 Adapter Sets 2 Suction Valve Inserts 1 Vent Valve2 Valve Balls 2 Valve Balls 1 Set of Seals 3 Adapter Sets1 Set of Seals 2 Ball Seat Disks 1 Connector Part

1 Set of Seals 2 Seals

Liquid Complete Spare Valves OnlyEnd Material Liquid Spare Parts (adapter sets not included)Version Code End Kit Suction Discharge Diaphragm

g/4b

1000-1 PP1 740409 740357 792644 740350 8114521001-1 PP3 740408 740356 792646 740351 811452

NP2 740407 740355 792119 740349 811452NP3 740406 740354 792026 740348 811452TT1 911311 912674 809407 809406 811452SS2 911317 912675 809424 809423 811452

1601-1 PP1 740413 740361 792644 740350 8114531602-1 PP3 740412 740360 792646 740351 811453

NP2 740411 740359 792119 740349 811453NP3 740410 740358 792026 740348 811453TT1 911338 912678 809407 809406 811453SS2 911344 912679 809424 809423 811453NS2 792239 792122 792119 792120 811453ES1 792551 792654 792611 792643 811543NS3 791849 792033 792026 792025 811453ES3 792552 792650 792646 792645 811453

1201-1 PP1 740417 740380 792644 740350 8114541203-1 PP3 740416 740364 792646 740351 811454

NP2 740415 740363 792119 740349 811454NP3 740414 740362 792026 740348 811454TT1 911365 912682 809407 809406 811454SS2 911371 912683 809424 809423 811454NS2 792241 792123 792119 792120 811454ES1 792553 792653 792611 792643 811454NS3 791850 792034 792026 792025 811454ES3 792554 792649 792646 792645 811454

0803-1 PP1 740421 740384 792644 740350 10025100806-1 PP3 740420 740383 792646 740351 1002510

NP2 740419 740382 792119 740349 1002510NP3 740418 740381 792026 740348 1002510TT1 911392 912686 809407 809406 1002510SS2 911398 912687 809424 809423 1002510NS2 792243 792124 792119 792120 1002510ES1 792555 792652 792611 792643 1002510NS3 791851 792035 792026 792025 1002510ES3 792556 792648 792646 792645 1002510

1002-1 PP1 740425 740388 792644 740350 8114561003-1 PP3 740424 740387 792646 740351 811456

NP2 740423 740386 792119 740349 811456NP3 740422 740385 792026 740348 811456TT1 911420 912690 809445 809444 811456SS2 911426 912691 809497 809496 811456PP4 910344 910174 7809456 7809456 811456PP5 7910344 910772 7809458 7809458 811456NS2 792245 792125 792119 792120 811456ES1 792557 792651 792611 792643 811456NS3 791852 792036 792026 792025 811456ES3 792558 792647 792646 792645 811456

0308-1 PP1 912227 912693 809439 809438 8114570313-1 PP2 7912237 910770 809449 809448 811457

NP1 912226 912692 809413 809412 811457NP2 740428 740391 740396 740395 811457TT1 911448 912694 809445 809444 811457SS2 911454 912695 809497 809496 811457

Pump Dim A Dim CVersion (mm) (mm)g/4b1000, 1001 31 101601, 1602 48 12.51201, 1203 48 160803, 0806 48 221002, 1003 60 220308, 0313 60 340215, 0223 76 42

g/5b1602 60 221605 60 341006 60 341310 76 420613 76 420813 76 510417 76 510423 126 700230 126 70

C

A

Discharge SuctionValve Valve1/4" 1/4"

Page 15: Cloradores Gamma

ProM

inen

t

gamma–15

ProMinent® gamma/b (new style)Spare Parts

Discharge SuctionValve Valve1/2" 1/2"

Spare parts and Liquid endsSpare Valves Only

Pump Material Liquid Spare Parts (adapter sets not included)Version Code End Kit Suction Discharge Diaphragm

g/4b (cont.)

0215-1 PP1 912232 912697 809439 809438 8114580223-1 PP2 7912238 910771 809449 809448 811458

NP1 912231 912696 809413 809412 811458NP2 740429 740392 740396 740395 811458TT1 911476 912698 809445 809444 811458SS2 911482 912699 809497 809496 811458

g/5b

1602-1 NP1 740582 740385 792026 740348 811456NP2 740490 740386 792119 740349 811456SS2 910820 912691 809497 809496 811456

1605-1 NP1 910821 912692 809413 809412 811457NP2 740430 740391 740396 740395 811457SS2 910823 912695 809497 809496 811457

1006-1 PP1 910822 912693 809439 809438 811457PP2 7910822 910770 809449 809448 811457NP1 910821 912692 809413 809412 811457NP2 740430 740391 740396 740395 811457TT1 910805 912694 809445 809444 811457SS2 910823 912695 809497 809496 811457PP4 910910 910940 7809459 7809459 811457PP5 7910910 910928 7809400 7809400 811457

1310-1 NP1 910807 912696 809413 809412 811458NP2 740431 740397 740396 740395 811458SS2 910826 912699 809497 809496 811458PP4 910911 910942 7809459 7809459 811458PP5 7910911 910929 7809400 7809400 811458

0613-1 PP1 910825 912697 809439 809438 811458PP2 7910825 910771 809449 809448 811458NP1 910824 912696 809413 809412 811458NP2 740431 740397 740396 740395 811458TT1 910809 912698 809445 809444 811458SS2 910826 912699 809497 809496 811458

0813-1 PP1 910828 910976 809439 809438 811459PP2 7910828 7910976 809449 809448 811459NP1 910827 910974 809413 809412 811459NP2 740432 740393 740396 740395 811459TT1 910813 910978 809445 809444 811459SS2 910829 910980 809497 809496 811459PP4 910912 910944 7809459 7809459 811459PP5 7910912 910930 7809400 7809400 811459

0417-1 PP1 910828 910976 809439 809438 811459PP2 7910828 7910976 809449 809448 811459NP1 910827 910974 809413 809412 811459NP2 740432 740393 740396 740395 811459TT1 910813 910978 809445 809444 811459SS2 910829 910980 809497 809496 811459

0423-1 PP1 910816 910992 809457 809457 811460PP2 7910816 7910992 7809457 7809457 811460NP1 910815 910990 809456 809456 811460NP2 740493 740398 740396 740395 811460TT1 910817 910994 809458 809458 811460SS1 910818 910996 809459 809459 811460

0230-1 PP1 910816 910992 809457 809457 811460PP2 7910816 7910992 7809457 7809457 811460NP1 910815 910990 809456 809456 811460NP2 740493 740398 740396 740395 811460TT1 910817 910994 809458 809458 811460SS1 910818 910996 809459 809459 811460

Page 16: Cloradores Gamma

ProM

inen

t

gamma–16

ProMinent® gamma/a (old style)Spare Parts

Pump Dim A Dim CVersion (mm) (mm)g/4a1000, 1001 31 101601, 1602 48 12.51201, 1203 48 160703, 0706 48 221002, 1003 60 220308, 0313 60 340215, 0223 76 42

g/5a1602 60 221605 60 341006 60 341310 76 420613 76 420813 76 510417 76 510423 126 700230 126 70

Spare parts and Liquid ends

Discharge SuctionValve Valve1/4" 1/4"

C

A

Complete liquid ends include pump head, valves, mounting screws, diaphragm and backplate. Spare parts kits include:

PP, NPLiquid Ends TT Liquid Ends SS Liquid Ends NS & PS Liquid Ends

1 Diaphragm 1 Diaphragm 1 Diaphragm 1 Diaphragm1 Suction Valve 1 Suction Valve 4 Valve Balls 1 Suction Valve1 Discharge Valve 1 Discharge Valve 1 Discharge Valve Inserts 1 Discharge Valve2 Adapter Sets 2 Adapter Sets 2 Suction Valve Inserts 1 Vent Valve2 Valve Balls 2 Valve Balls 1 Set of Seals 3 Adapter Sets1 Set of Seals 2 Ball Seat Disks 1 Connector Part

1 Set of Seals 2 Seals

Complete Spare Valves OnlyPump Material Liquid Spare Parts (adapter sets not included)Version Code End Kit Suction Discharge Diaphragm

g/4a

1000 PP1 912202 912673 809429 809428 8114521001 PP2 7912239 910765 7809429 7809428 811452

NP1 912201 912672 809409 809408 811452TT1 911311 912674 809407 809406 811452SS2 911317 912675 809424 809423 811452

1601 PP1 912207 912677 809431 809430 8114531602 PP2 7912233 910766 7809431 7809430 811453

NP1 912206 912676 809411 809410 811453TT1 911338 912678 809407 809406 811453SS2 911344 912679 809424 809423 811453NS3 791849 792033 792026 792025 811453PS3 791853 792033 792026 792025 811453

1201 PP1 912212 912681 809431 809430 8114541203 PP2 7912234 910767 7809431 7809430 811454

NP1 912211 912680 809411 809410 811454TT1 911365 912682 809407 809406 811454SS2 911371 912683 809424 809423 811454NS3 791850 792034 792026 792025 811454PS3 791854 792034 792026 792025 811454

0703 PP1 912217 912685 809431 809430 8114550706 PP2 7912235 910768 7809431 7809430 811455

NP1 912216 912684 809411 809410 811455TT1 911392 912686 809407 809406 811455SS2 911398 912687 809424 809423 811455NS3 791851 792035 792026 792025 811455PS3 791855 792035 792026 792025 811455

1002 PP1 912222 912689 809439 809438 8114561003 PP2 7912236 910769 809449 809448 811456

NP1 912221 912688 809413 809412 811456TT1 911420 912690 809445 809444 811456SS2 911426 912691 809497 809496 811456PP4 910344 910174 809457 809457 811456PP5 7910344 910772 7809457 7809457 811456NS3 791852 792036 792026 792025 811456PS3 791856 792036 792026 792025 811456

0308 PP1 912227 912693 809439 809438 8114570313 PP2 7912237 910770 809449 809448 811457

NP1 912226 912692 809413 809412 811457TT1 911448 912694 809445 809444 811457SS2 911454 912695 809497 809496 811457

Page 17: Cloradores Gamma

ProM

inen

t

gamma–17

ProMinent® gamma/a (old style)Spare Parts

Spare Valves OnlyPump Material Liquid Spare Parts (adapter sets not included)Version Code End Kit Suction Discharge Diaphragm

g/4a (cont.)

0215 PP1 912232 912697 809439 809438 8114580223 PP2 7912238 910771 809449 809448 811458

NP1 912231 912696 809413 809412 811458TT1 911476 912698 809445 809444 811458SS2 911482 912699 809497 809496 811458

g/5a

1602 NP1 910819 912688 809413 809412 811456SS2 910820 912691 809497 809496 811456

1605 NP1 910821 912692 809413 809412 811457SS2 910823 912695 809497 809496 811457

1006 PP1 910822 912693 809439 809438 811457PP2 7910822 910770 809449 809448 811457NP1 910821 912692 809413 809412 811457TT1 910805 912694 809445 809444 811457SS2 910823 912695 809497 809496 811457PP4 910910 910940 809402 809402 811457PP5 7910910 910928 7809400 7809400 811457

1310 NP1 910824 912696 809413 809412 811458SS2 910826 912699 809497 809496 811458PP4 910911 910942 809402 809402 811458PP5 7910911 910929 7809400 7809400 811458

0613 PP1 910825 912697 809439 809438 811458PP2 7910825 910771 809449 809448 811458NP1 910824 912696 809413 809412 811458TT1 910809 912698 809445 809444 811458SS2 910826 912699 809497 809496 811458

0813 PP1 910828 910976 809439 809438 811459PP2 7910828 7910976 809449 809448 811459NP1 910827 910974 809413 809412 811459TT1 910813 910978 809445 809444 811459SS2 910829 910980 809497 809496 811459PP4 910912 910944 809402 809402 811459PP5 7910912 910930 7809400 7809400 811459

0417 PP1 910828 910976 809439 809438 811459PP2 7910828 7910976 809449 809448 811459NP1 910827 910974 809413 809412 811459TT1 910813 910978 809445 809444 811459SS2 910829 910980 809497 809796 811459

0423 PP1 910816 910992 809457 809457 811460PP2 7910816 7910992 7809457 7809457 811460NP1 910815 910990 809456 809456 811460TT1 910817 910994 809458 809458 811460SS1 910818 910996 809459 809459 811460

0230 PP1 910816 910992 809457 809457 811460PP2 7910816 7910992 7809457 7809457 811460NP1 910815 910990 809456 809456 811460TT1 910817 910994 809458 809458 811460SS1 910818 910996 809459 809459 811460

Spare parts and Liquid ends

Discharge SuctionValve Valve1/2" 1/2"

Page 18: Cloradores Gamma

ProM

inen

t

gamma–18

Description Part No.

Spare fuses

gamma 4/b fuse, 115 VAC, 0.5 A, ATT 712037gamma 4/b fuse, 230 VAC, 0.25 A, ATT 712035gamma 5/b fuse, 115 VAC, 120 spm, 1.0 A, ATT 712052gamma 5/b fuse, 115 VAC, 100 spm, 1.25 A, ATT 712038gamma 5/b fuse, 230 VAC, 120 spm, 0.5 A, ATT 712037gamma 5/b fuse, 230 VAC, 100 spm, 0.7 A, ATT 712051

ProMinent® gamma/bSpare Parts

Page 19: Cloradores Gamma

ProM

inen

t

gamma–19

Description Qty. Part No.

1201-1/1203-1 PP1 liquid end complete 1 740417

1 backplate g1201 (blue) ........................... 1 8007032 DEVELOPAN diaphragm........................ 1 8114543 O-ring 3.68 x 1.78 EPDM ....................... 1 4804034 tube nozzle bypass PP ........................... 1 8006135 dosing head body only 1201-1 PP ......... 1 7918676 bleed valve complete EPDM .................. 1 8094907 screw M4 x 65 (with washer) .................. 4 4686418 cover plate with print PP ........................ 1 8006749 bleed valve knob PP............................... 1 800832A connector set 1/4" PP1 ........................... 1 817150B discharge valve g/b 1/4" PP1 ................. 1 740350C suction valve g/b 1/4" PP1 ..................... 1 792644* indicates location of spring if needed

A connector set 1/4" PP1 1 817150a1 union nut M20 x 1.5 PP ............... 2 800608a2 clamp ring 1/4" PP ....................... 2 800617a3 tube nozzle 3/16" PP ................... 2 800609a4 O-ring 9 x 2.5 EPDM ................... 2 791495

B discharge valve g/b 1/4" PP1 1 740350b1 dis. valve body g/b 1/4" PP .......... 1 791876b2 valve insert 4.7-1 PP ................... 1 791872b3 valve ball 4.7mm Ceramic ........... 2 404201b4 ball seat 3 x 9.5 EPDM ................ 2 791870b5 O-ring 9 x 2.5 EPDM ................... 1 791495b6 valve insert (dis.) 4.7-1 PP .......... 1 791875b7 O-ring 14 x 2 EPDM .................... 1 791641

C suction valve g/b 1/4" PP1 1 792644c1 sealing gasket 18 x 2.5 EPDM .... 1 791871c2 valve insert 4.7-1 PP ................... 2 791872c3 valve ball 4.7mm Ceramic ........... 2 404201c4 ball seat 3 x 9.5 EPDM ................ 2 791870c5 distance sleeve (suction) PP ....... 1 791873c6 suction valve body g/b PP ........... 1 800671

Spare Parts Set 1201-1/1203-1 PP1 1 740380

A connector set 1/4" PP1 ................ 1 817150B discharge valve g/b 1/4" PP1 ...... 1 740350C suction valve g/b 1/4" PP1 ........... 1 7926442 DEVELOPAN diaphragm ............. 1 8114543 O-ring 3.68 x 1.78 EPDM ............ 3 4804036 O-ring (bleed valve) EPDM ......... 1 480408b5 O-ring 9 x 2.5 EPDM ................... 3 791495b7 O-ring 14 x 2 EPDM .................... 1 791641c1 sealing gasket 18 x 2.5 EPDM .... 1 791871c3 valve ball 4.7mm Ceramic ........... 2 404201c4 ball seat 3 x 9.5 EPDM ................ 4 791870

gamma/4b 1201-1/1203-1 PP1 Liquid End Complete

a1

a2

a4

a3

a1

a2

a3

a4

b1

b2

b3

b4

b5

b6

b3b4

b7

A

B

C

3

4

5

6 78

*

*

c3c4

c2

c2

c3c4

c5

c6

c121 9

#G4B3PP1-1/97NA

Exploded View

Page 20: Cloradores Gamma

ProM

inen

t

gamma–20

Description Qty. Part No.

1601-1/1602-1 NS3 liquid end complete 1 791849

1 backplate g1601 (blue) ........................... 1 8007022 DEVELOPAN diaphragm........................ 1 8114533 dosing head body 1601 sdb Acrylic ........ 1 7918304 screw M4 x 55 ........................................ 4 4686385 O-ring 13 x 2.5 Viton® ............................. 2 7911126 connect. part sdb PVC ........................... 2 791086A suct.valve cpl. b-type 1/4" PS3 ............... 1 792026B vent valve cpl. sdb PVDF ....................... 1 792027C discharge valve cpl. sdb PS3 ................. 1 792025D connector set sdb 1/4" PS3 .................... 3 791163

A suct. valve cpl. b-type 1/4" PS3 1 792026a1 sealing gasket 18 x 2.5 Viton® .......... 1 791051a2 valve insert 4.7-1 PVC ................. 2 791090a3 valve ball 4.7mm Ceramic ........... 2 404201a4 ball seat 3 x 9.5 Viton® .............................. 2 792759a5 distance sleeve (suction) PVC..... 1 791089a6 suct. valve body b-type PVC ....... 1 800569

B vent valve cpl. sdb PVDF 1 792027b1 valve box deairing PVDF ............. 1 791838b2 O-ring 12.37 x 2.62 Viton® ..................... 1 791131b3 ball seat disc 8.95 x 2.1 Ceramic 1 791817b4 deairing insert PVDF ................... 1 791839b5 valve ball 5mm Ceramic .............. 1 791816b6 ball seat disc 8.95mm Ceramic ... 1 404032b7 gasket 11.9 x 8 x 1.5 PTFE ......... 1 791826

C discharge valve cpl. sdb PS3 1 792025c1 O-ring 3.68 x 1.78 Viton® ........................ 1 791109c2 valve ball 4.7mm Ceramic ........... 1 404201c3 conical spring .............................. 1 791052c4 O-ring 12.37 x 2.62 Viton® .................... 1 791131c5 discharge valve body sdb PVC ... 1 791087

D connector set sdb 1/4" PS3 *3 791163d1 O-ring 9 x 2.5 Viton® .................................... 1 791421d2 tube nozzle 3/16" PVC ................ 1 800520d3 clamp ring 1/4" Ferrule ................ 1 800712d4 union nut M20 x 1.5 PVC ............ 1 800518

* NS3 liquid ends ship with 3 connector sets.Quantities reflect # of components in each set.

Spare Parts Set 1601-1/1602-1 PS3 1 792033

A suct. valve cpl. b-type 1/4" PS3 ... 1 792026B vent valve cpl. sdb PVDF ............ 1 792027C discharge valve sdb PS3 ............. 1 792025D connector set sdb 1/4" PS3 ......... 3 7911632 DEVELOPAN diaphragm ............. 1 8114535 O-ring 13 x 2.5 Viton® ................................. 2 7911126 connect. part sdb PVC ................ 1 791086

d4

d3

d2

d1

b1

b2b3b4b5b6b7

B

Cc1c2c3c4 c5

6

5

12 3

4

6

5

d4

d3

d2

d1

a1

a4a3a2

a2a3a4

a5

a6

A

d4

d3

d2

d1

D

gamma/4b 1601-1/1602-1 NS3 Liquid End Complete

#G4B2NS3-1/97NA

Exploded View

Page 21: Cloradores Gamma

ProM

inen

t

gamma–21

gamma/5b 0813-1 NP1 Liquid End Complete

b1

b2

b5b4b3

b6

b2b3b4

b7

a1

a2

a4

a3 A

B

*

c3c4c5

c2

c6

c1c7c4

c8

c9

c5

a4

a3

a1

a2

* C

12

3

4

5 c1

6 7 8 9

Description Qty. Part No.

0813-1 NP1 liquid end complete 1 910827

1 backplate g0813 (blue) ........................... 1 8007692 DEVELOPAN diaphragm........................ 1 8114593 O-ring 3.68 x 1.78 Viton® ........................................... 1 4810034 tube nozzle bypass PVC ........................ 1 8005195 dosing head body only 0813 Acrylic ....... 1 8107606 bleed valve complete Viton® .................................. 1 8094917 screw M5 x 60 ........................................ 4 4680778 washer .................................................... 4 4622289 bleed valve knob PP............................... 1 800632A connector set 1/2" PC1 .......................... 1 817055B discharge valve g/b 1/2" PC1 ................. 1 809412C suction valve g/b 1/2" PC1 ..................... 1 809413* indicates location of spring if needed

A connector set 1/2" PC1 1 817055a1 union nut M20 x 1.5 PVC 2 800518a2 clamp ring 1/2" PVC 2 800715a3 tube nozzle 3/8" PVC 2 800530a4 O-ring 9 x 2.5 Viton® 2 791421

B discharge valve g/b 1/2" PC1 1 809412b1 dis. valve body g/b 1/2" PVC ....... 1 800568b2 valve ball 9.2mm Ceramic ........... 2 404281b3 ball seat disc PVC ....................... 2 140554b4 O-ring 3.68 x 1.78 Viton® ........................ 2 481007b5 O-ring 8.3 x 2.4 Viton® ............................... 1 481008b6 valve insert 9.2 x 23 PVC ............ 1 800527b7 O-ring 13 x 2.5 Viton® ................................. 1 481013

C suction valve g/b 1/2" PC1 1 809413c1 valve ball 9.2mm Ceramic ........... 2 404281c2 ball seat disc (suction) PVC......... 1 811525c3 O-ring 13 x 2.5 Viton® ................................. 1 481013c4 O-ring 3.68 x 1.78 Viton® ........................ 2 481007c5 O-ring 8.3 x 2.4 Viton® ............................... 2 481008c6 valve insert 9.2 x 23 PVC ............ 1 800527c7 ball seat disc PVC ....................... 1 140554c8 valve insert 13 x 18 PVC ............. 1 800517c9 suct. valve body g/b PVC ............ 1 800569

Spare Parts Set 0813-1 NP1 1 910974

A connector set 1/2" PC1 ................ 1 817055B dis. valve g/b 1/2" PC1 ................ 1 809412C suction valve g/b 1/2" PC1 .......... 1 8094132 DEVELOPAN diaphragm ............. 1 811459c1 valve ball 9.2mm Ceramic ........... 2 404281c2 ball seat disc (suction) PVC ........ 1 811525c3 O-ring 13 x 2.5 Viton® ................................. 2 481013c4 O-ring 3.68 x 1.78 Viton® ........................ 4 481007c5 O-ring 8.3 x 2.4 Viton® ............................... 3 481008c7 ball seat disc PVC ....................... 3 140554

#G5B6NP1-1/97NA

Exploded View

Page 22: Cloradores Gamma

ProM

inen

t

gamma–22Gamma/b-1

((THIS IS A MASTER, EDIT FOR SPECIFIC APPLICATION))PROMINENT FLUID CONTROLS, INC. - GAMMA/4b and 5/b (for flow rates up to 8 gph)

SECTION _______- CHEMICAL METERING PUMPS

1.1 APPLICATIONA. Quantity:_________B. Chemical Service:_______________________C. Tag. Nos.:____________________________D. Capacity (US gallons per hour)_______________________E. Backpressure (psig):_______________________

1.2 DESCRIPTIONA. The chemical metering pump(s) shall be a microprocessor-controlled, simplex, solenoid-

driven, reciprocating, mechanically-actuated diaphragm type. All pumping functions shall beset by membrane-switch keypad and status shall be displayed on an illuminated LCD. Thehousing shall be rated NEMA 4X.

B. The manufacturer shall provide a two year warranty on the pump drive and one year war-ranty on the pump liquid end, including diaphragm and O-rings. The pump shall be fullytested to meet rated flow and pressure by the manufacturer.

C. The power supply shall be ____ VAC, ____ Hz, single phase. The microprocessor is toautomatically compensate for supply voltage variations within 15% of the rated voltage suchthat frequency of the pump remains constant.

D. The liquid end shall be physically separated from the drive unit by back plate with weep holecreating an air gap. An elastomer shaft wiper seal shall prevent contamination of the solenoid if the primary diaphragm fails. The diaphragm shall be nylon-reinforced EPDM withPTFE-faced fluid contact surface.

1.3 LIQUID END ((SELECT ONE))- The liquid end shall be glass-filled polypropylene, with built coarse valve and needle valve

for air bleed, manually adjusted for continuous degassing of process fluid and self-primingagainst pressure. The suction and discharge valve shall be of the double ball check design.

- The liquid end shall be glass-filled polypropylene, suitable for pumping high viscosity fluids,with spring-loaded single ball check valves.

- The liquid end shall be Plexiglas® (acrylic) with built coarse valve and needle valve for airbleed, manually adjusted for continuous degassing of process fluid and self-priming againstpressure. The suction and discharge valve shall be PVC, with double ball check design

- The liquid end shall be of the self-degassing type, with integral automatic air relief valve forself priming under maximum rated discharge line pressure. The liquid end shall be con-structed of ((Acrylic or PVC)) The suction valve shall be of the double ball check design anddischarge valve shall be spring loaded, horizontally acting single ball design.

- The liquid end shall be constructed of carbon-filled PTFE. The suction and discharge valveshall be of the double ball check design.

- The liquid end shall be constructed of 316 stainless steel. The suction and discharge valveshall be of the double ball check design.

Page 23: Cloradores Gamma

ProM

inen

t

gamma–23

1.4 CONTROLA. Stroke length control shall be manually adjusted between 100% and 0% with a stroke adjust-

ing knob on the pump control face.B. Stroke frequency control shall be manually adjusted by touch key pads, with the set stroke

rate displayed on the LCD. The metering pump shall be capable of receiving a pulse input viaoptional external control cable such that 1 pulse gives 1 pump stroke. The metering pumpshall be capable of remote ON-OFF operation using the PAUSE function via a voltage-freecontact relay through an optional control cable.((OPTIONAL)) PULSE MULTIPLIER/DIVIDER - The metering pump shall allow factor-ing to issue from 1 to 9,999 strokes per pulse input or to issue 1 stroke per 1 to 9,999 inputpulses.((OPTIONAL)) ANALOG - The pump shall accept an analog signal such that strokefrequency is proportional to a ((SELECT ONE: 0/4-20 mA, 20-4/0 mA, 0/12-60 mV, 0/0.2-1V, 0/2-10V) signal. The pump shall allow setting of a maximum stroke rate which corre-sponds to the maximum analog signal, with stroke rate proportional to signal strength belowthat rate. Analog-to-digital converters external to the pump shall not be allowed.

1.5 FLOW ASSURANCE ((OPTIONAL))A. Low Level Control - A 2-stage Float Switch shall be supplied to stop the pump prior to

losing prime and annunciate low level on the pump LCD.B. Flow Monitor - A Flow Monitor shall be installed on the discharge line to automatically stop

pumping and annunciate a fault condition on the pump LCD upon loss of discharge flow.C. Relay Output - An SPDT relay shall be installed on the pump for: ((SELECT ONE))- Fault Indication - ((OPTIONAL)) the metering pump shall have an integral relay to allow

remote annunciation of a fault condition (i.e. low supply solution early warning/lack ofsupply solution shut down, flow monitor, system faults, and fuse/power supply failure).

- Pacing Relay - ((OPTIONAL)) the metering pump shall have an integral relay to issue acontact closure with every pump stroke to pace a second PROMINENT metering pump.

1.6 ACCEPTABLE MANUFACTURER:A. ProMinent Fluid Controls, model _______________________________B. Or pre-approved equal.

1.7 ACCESSORIES ((ALL ARE OPTIONAL AND MAY BE INCLUDED AS SEPARATEITEMS OR AS COMPONENTS OF A PUMP STAND))

A. The pump shall be mounted on a ((CHOOSE ONE: Fiberglass Reinforced Plastic / StainlessSteel)) support stand suitable for wall, floor or top-of-tank mounting, and including thefollowing accessories pre-piped and factory tested:

B. A foot valve and strainer shall be provided with each pump.C. An injection check valve shall be provided with each pump.D. A universal control cable with 4 pole round plastic connector and 4-wire cable with loose

ends shall be provided with each pump.E. A two stage float switch compatible with the chemical metering pump shall be provided for

monitoring tank level.F. An adjustable discharge flow monitoring device shall be provided. The flow monitor shall

be capable of signaling a fault condition to the metering pump.G. A diaphragm failure detector shall be provided to ((open/close)) a contact in the event of

diaphragm failure.

Gamma/b-2

Page 24: Cloradores Gamma

ProM

inen

t

gamma–24Gamma/b-3

H. An adjustable-pressure, diaphragm-type back pressure/antisiphon valve shall be providedwith each metering pump.

I. An in-line, adjustable-pressure, diaphragm-type pressure relief valve shall be provided witheach metering pump.

J. A pump-mounted, multi-function, fixed-spring pressure diaphragm-type valve forbackpressure/antisiphon protection, pressure relief, priming and discharge line drain shall beprovided with each metering pump.

K. An air-charged, bladder-type pulsation dampener shall be provided with each meteringpump.

L. A clear PVC calibration column with FNPT fittings top and bottom shall be provided witheach pump.

M. Fifteen feet of tubing compatible with the fluid pumped shall be provided with each pump.

END OF SECTION