class 150 standard

PROJECT INFORMATION APPROVAL STAMPProject: Approved

Address: Approved as noted

Contractor: Not approved

Engineer: Remarks:

Submittal Date:

Notes 1: Notes 2:

PS-11.16 page 1 PS-SUB-1106-1106R-1107-v01 20211118

Anvil® Malleable Iron Fittings

Tee & Cross (Class 150 Standard)Fig. 1106 Street or Service Tee (Straight)Fig. 1106R Street or Service Tee (Reducing)Fig.1107 Cross

Fig. 1106

Fig. 1107

Malleable Iron Threaded Pipe Unions Pressure - Temperature Ratings

Temperature

Pressure

Class 150 Class 250 Class 300

°F/°C PSI/bar PSI/bar PSI/bar

-20°—150° 300 500 600-28.9°—65.6° 20.7 34.5 41.4

200° 265 455 55093.3° 18.3 31.4 37.9250° 225 405 505

121.1° 15.5 27.9 34.8300° 185 360 460

148.9° 12.8 24.8 31.7350° 150 315 415

176.7° 10.3 21.7 28.6400° 110 270 370

204.4° 7.6 18.6 25.5450° 75 225 325

232.2° 5.2 15.5 22.4500° — 180 280

260.0° — 12.4 19.3550° — 130 230

287.8° — 9.0 15.9

Malleable Iron Threaded Fittings Pressure - Temperature Ratings

Temperature

Pressure

Class 150

Class 300Sizes

1/4"–1"(6-25mm)

Sizes 1 1/4"–2"

(32-51mm)

Sizes 2 1/2"–3"

(64-76mm)

°F/°C PSI/bar PSI/bar PSI/bar PSI/bar

-20°–150° 300 2000 1500 1000-28.9°–65.6° 20.7 137.9 103.4 68.9

200° 265 1785 1350 91093.3° 18.3 123.1 93.1 62.7250° 225 1575 1200 825

121.1° 15.5 108.6 82.7 56.9300° 185 1360 1050 735

148.9° 12.8 93.8 72.4 50.7350° 150 1150 900 650

176.7° 10.3 79.3 62.1 44.8400° — 935 750 560

204.4° — 64.5 51.7 38.6450° — 725 600 475

232.2° — 50.0 41.4 32.8500° — 510 450 385

260.0° — 35.2 31.0 26.5550° — 300 300 300

287.8° — 20.7 20.7 20.7

ASC Engineered Solutions™ offers the broadest line of malleable iron fitting sizes in both black and galvanized finishes. Every fitting is manufactured and tested to meet ASC's strict quality standards. All Anvil Class 150 Malleable Iron Fittings conform to ASME B16.3 and unions conform to ASME B16.39. All elbows and tees 3/8" (10 DN) and larger are 100% gas tested at a minimum of 100 PSI (6.9 bar).For Listings/Approval Details and Limitations, visit our website at www.asc-es.com or contact an ASC Engineered Solutions™ Representative.See following page for standards and specifications.Anvil Class 150/300 Malleable Iron Fittings conform to ASME B16.3 and Unions conform to ASME B16.39. All elbows and tees 3/8" (10 DN) and larger are 100% gas tested at a minimum of 100 PSI (6.9 bar).

Note: Unions with Copper or Copper Alloy seats are not intended for use where temperature exceeds 450°F.

Fig. 1106R

asc-es.com


PS-11.16 page 2 PS-SUB-1106-1106R-1107-v01 20211118

Tee & Cross (Class 150 Standard) Fig. 1106, 1106R, 1107

Note:

* ASTM B633. Type I, SC 4, may be supplied as alternate zinc coating per applicable ASME B16 product standard.

Malleable Iron Fittings

Dimensions Material Galvanizing* Thread Pressure Rating

Class 150/PN 20 ASME B16.3 ASTM A197 ASTM A153 ASME B1 20.1 ASME B16.3


Malleable Iron Unions

Dimensions Material Galvanizing* Thread Pressure Rating


Class 250 ASME B16.39 ASTM A197 ASTM A153 ASME B1 20.1 ASME B16.39


Standards and Specifications

asc-es.com


PS-06.13 page 3 PS-SUB-1106-1106R-1107-v01 20211118

Size AUnit Weight

Black Galvanized

NPS/DN In./mm Lbs./kg Lbs./kg

1/8 11/16 0.12 0.126 17 0.05 0.05

1/4 13/16 0.18 0.188 22 0.08 0.08

3/8 15/16 0.28 0.2810 24 0.13 0.13

1/2 1 1/8 0.42 0.4215 29 0.19 0.19

3/4 1 5/16 0.69 0.6920 33 0.31 0.31

1 1 1/2 1.12 1.1225 38 0.51 0.51

1 1/4 1 3/4 1.44 1.4432 44 0.65 0.65

1 1/2 1 15/16 1.98 1.9840 49 0.90 0.90

2 2 1/4 3.30 3.3050 57 1.50 1.50

2 1/2 2 11/16 5.90 5.9065 68 2.68 2.68

3 3 1/16 7.94 7.9480 78 3.60 3.60

4 3 13/16 13.50 13.50100 98 6.12 6.12

Size A JUnit Weight

Black Galvanized

NPS/DN In./mm In./mm Lbs./kg Lbs./kg

1/4 1 3/16 1 3/16 0.15 0.158 30 30 0.07 0.07

3/8 1 5/16 1 7/16 0.24 0.2410 33 37 0.11 0.11

1/2 1 1/8 1 5/8 0.34 0.3415 29 41 0.15 0.15

3/4 1 5/16 1 7/8 0.61 0.6120 33 48 0.28 0.28

1 1 1/2 2 1/8 0.96 0.9625 38 54 0.44 0.44

1 1/4 1 3/4 2 7/16 1.39 1.3932 44 62 0.63 0.63

1 1/2 1 15/16 2 11/16 1.93 1.9340 49 68 0.88 0.88

2 2 1/4 3 1/4 3.16 3.1650 57 83 1.43 1.43

Size female run x

male run x outlet

Run Outlet Unit Weight

A J A Black Galvanized

NPS/DN In./mm In./mm In./mm Lbs./kg Lbs./kg

1 1/4 x 1 x 1 1/4 1 3/4 2 5/16 1 3/4 1.34 1.3432 x 25 x 32 44 59 44 0.61 0.61

Fig. 1107Cross (Class 150 Standard)

Fig. 1106, 1106RStraight Street or Service Tee (Class 150 Standard) Reducing Street or Service Tee (Class 150 Standard)

Notes:

See first page for pressure-temperature ratings. Galvanized weights may vary. Please contact your ASC Engineered Solutions™ Representative if you need verification.

All elbows and tees 3/8" (10 DN) and larger are 100% gas tested at a minimum of 100 PSI (6.9 bar).

asc-es.com

PS-11.13 page 4 PS-SUB-1106-1106R-1107-v01 20211118

Malleable Iron Fittings / Installation

Fig. 1106, 1106R, 1107 Tee & Cross (Class 150 Standard)

1 Inspect both male and female components prior to assembly.• Threads should be free from mechanical damage, dirt, chips and excess cutting oil.• Clean or replace components as necessary.

2 Application of thread sealant• Use a thread sealant that is fast drying, sets-up to a semi hard condition and is vibration resistant. Alternately, an anaerobic sealant may be utilized.• Throroughly mix the thread sealant prior to application.• Apply a thick even coat to the male threads only. Best application is achieved with a brush stiff enough to force sealant down to the root of the threads.

3 Joint Makeup• For sizes up to and including 2" pipe, wrench tight makeup is considered three full turns past handtight. Handtight engagement for 1⁄2" through 2"

thread varies from 4 1⁄2 turns to 5 turns.

• For 2 1⁄2" through 4" sizes, wrench tight makeup is considered two full turns past handtight. Handtight engagement for 2

1⁄2" through 4" thread varies from 5

1⁄2 turns to 6 3⁄4 turns.

General Assembly of Threaded Fittings

class 150 standard

Documents