city council agenda item - vero beach, florida898790a2-f88a-48ae-a9b3-666aae67ad… · city council...

City Council Agenda Item Meeting of August 18, 2015

TO: The Honorable Mayor and Members of the City Council

FROM: James R. O'Connor, City ManaV-

DATE: August 11, 2015

SUBJECT: North Beach Substation 15kv Switchgear Replacement

REQUESTED BY: City Manager/Electrical T&D Department

The following is requested as it relates to the above-referenced agenda item:

_2S_ Request Council review and approval based on the attached supporting documentation.

No action required. (Information only)

Departmental Correspondence

E-Mail: [email protected]

TO: James R. O'Connor, City Manager DEPT: City Manager

FROM: Ted Fletcher, Director, Electric Utility Operations Jf' DEPT: Electrical T&D

DATE: August 7, 2015

SUBJECT: North Beach Substation 15kv Switchgear Replacement

Background: Substation Nine (9) provides electric service to the North Beach area and is used as

backup substation for Central Beach - Substation Ten (10). Through routine testing it was determined that bus one (1), low side distribution switchgear at Substation Nine (9), does not meet IEEE insulation ratings.

Funding: Funding will come from Electric Switchgear Rebuild account# 403.5400.531.613001.

This is an approved budget item in the 2014-2015 Five-year CIP.

Recommendation:

I am requesting approval for the following item:

The item is for 15KV Switchgear Replacement totaling to $616,228. The work will be executed by currently contracted engineering firm Aubrey Silvey Enterprises, Inc. It will include purchasing, removal of existing switchgear, installation, testing and commissioning, and coordination with the switchgear manufacturer ABB Inc. which has met City ofVero Beach's construction standards requirements.

SWOT Analysis: Strengths: The new switchgear is compliant to the new industry standards. It will perform

at seasonal load peak demands and will allow for more distribution redundancy.

Weaknesses: None.

Opportunities: By replacing the switchgear, relay synchronization and telemetry data pertaining to the status of the switchgear and feeders in the electric distribution system will be available.

Threats: If not replaced, the 69kv transformer at Substation Ten (10) will become inadequate in carrying the necessary electric load needed to service customers.

mailto:[email protected]

_______ENTERPRISES, INC________ ')1.n

existing power cables and supply new control cables. Once the transformer is reconnected, Bus B will need to be de-energized a second time. Bus A and Bus B will then be re-connected to the original configuration.

New low voltage AC and DC power cable will be run to the existing control house to provide power to the new switchgear. We have assumed adequate capacity is available in both existing AC and DC systems.

For more information on the switchgear, please see the attached literature provided by ABB. ABB has been proposed due to their familiarity with the Substation 11 project and their anticipated delivery schedule. We have also provided quotations from Powell and Siemens for review.

Commercial

Base Price (Excludes Gear): ............................. $ 288,059 sales and use taxes (Two hundred and eighty-eight thousand and fifty-nine dollars)

We have an allowance in this price for $2,000.00 of miscellaneous conduit and fittings.

We have an allowance in this price of $1,500.00 for yard stone. We have an allowance in this price of $5,000.00 for old switch gear disposal

Switchgear (Direct Purchase to ABB): ............... $328,169

Pricing is based on using ABB Switchgear and includes the following items (including all applicable freight):

Total Project Project Value: ................................ $ 616,228

B t T bl S'I1vey Base P.nee reakou a e Hourly Rate

Man Hours Selling Price

Control Cable $6,172.02

Bus Duct $50,447.62

Miscellaneous $617.20

Construction Laborer $ 62.50 2,663.93 $166,495.84

Testing Technician $110.00 129.05 $14,195.65

Project Management $ 125.00 149.62 $18,703.09

Engineer $175.00 179.59 $31,427.92

Total 288,059.34

Page2 of3

http:5,000.00http:1,500.00http:2,000.00

A01 Switchgear ABB type Advance Metal-Clad Switchgearlndoor, rated 15 kV, 2000 A, 25 kA, 3-phase 3-wire, 60 Hz, 95 kV BIL consisting of (6) cubicles with (5) ADVAC vacuum circuit breakers, complete with specified equipment per the attached bill of material.

A02 Accessories - Accessories & Special Tools - please refer to item bill of material for detailed list and unit prices.

A03 Spare parts - please refer to bill of material for detailed list and unit prices.

A04 Sheltered Aisle shipping - Transportation to Vero Beach

AOS Sheltered Aisle - Enclosure

A07CPT Transportation of SWG to Vero Beach - FOB Job Site

The following items are excluded from our base price and be can be added at a later date.

A06 G&T Electric Device Accessories & Special Tools - please refer to item bill of material for detailed list and unit prices.

Commercial I Technical Clarifications: 1

All unforeseen subsurface conditions (such as rock, water, etc.) are excluded. Payment terms, Net 30 days of approved invoice based on progress billing. Silvey price is valid for thirty days.

Thank you again for this opportunity. If you have any questions regarding this proposal please call me at 770-537-1144, ext. 251.

Sincerely,

Aubrey Silvey Enterprises, Inc.

EPC Division

,,,7 ' /// /7//

(_./~/,/ ft/" V{/w_-;:t,..,tY.' /,,{f/:Zm~.r'~Ji(/, /

loseph W. Murrah Vice President

Page3 of 3

MEDIUM-VOLTAGE CIRCUIT BREAKER SWITCHGEAR

METAL-CLAD, VACUUM, 15 kV

PART 1 - GENERAL

1.1 SCOPE

A. This section includes medium-voltage, metal-clad circuit breaker switchgear and its associated auxiliary equipment. The equipment shall consist of walk-in switchgear with horizontal drawout, vacuum circuit breakers.

1.2 RELATED DOCUMENTS

A. Drawings and general prov1s1ons of the Contract, including General and Supplementary Conditions apply to this Section.

1.3 SUBMITT ALS

A. Submit shop drawings and product information for approval and final documentation in the quantities listed according to the Conditions of the Contract. All transmittals shall be identified by purchaser name, purchaser location and purchaser's order number.

B. Approval documents shall include: 1. General arrangement drawing showing dimensioned elevation and floor plan, foundation

details and one-line diagram 2. Panel arrangement drawing showing layout of devices on the panel doors 3. Three-line diagrams 4. Schematics 5. Nameplate engraving drawings 6. Electrical bill of material.

C. Final documents shall include: 1. Documents listed in 1.3.B above 2. Wiring diagrams 3. Recommended spare parts list for start-up support 4. Instruction manual.

1.4 QUALITY ASSURANCE

A. Manufacturer qualifications: The bidder must have at least 15-years experience in manufacturing medium-voltage metal-clad switchgear and circuit breakers. The manufacturer of the metal-clad switchgear assembly shall also be the manufacturer of the circuit breakers.

B. Comply with requirements of latest revisions of applicable industry standards, specifically including the following: 1. ANSI/IEEE C37.20.2 - Metal-Clad Switchgear 2. ANSI/IEEE C37.04 - Rating Structure for High Voltage Circuit Breakers 3. ANSI/IEEE C37.06 - Preferred Ratings for High Voltage Circuit Breakers 4. ANSI/IEEE C37.90 - Relays and Relay Systems.

1.5 DELIVERY, STORAGE AND HANDLING

A. Deliver in convenient shipping groups. Shipping groups shall not exceed 15 feet in length.

B. Circuit breakers shall be shipped inside their respective cells.

C. The accessory cabinet shall be shipped attached to the switchgear.

D. Bus bars with associated hardware for connections between shipping groups shall be shipped inside one of the units in which shall be installed.

E. Contractor shall store the equipment in accordance with manufacturer's recommendations.

June 19, 2015 City of Vero Beach Sub #11 Switchgear 1 Replacement MV Circuit Breaker Switchgear 1

proper bond between the epoxy and the bus bar, eliminating partial discharges. Each bus segment shall be individually high-potential tested prior to assembly. Taped joints are not permitted except in unusual joint configurations. The ground bus shall be bare silver-plated, copper; at least Y.I by two inches and shall extend the full length of switchgear.

E. Each circuit breaker compartment shall contain a racking mechanism, circuit breaker operated (not racking mechanism operated) automatic shutters and safety interlocks.

F. Each circuit breaker cell shall also include: 1. Hinged front panel. 2. Primary and secondary disconnecting devices. 3. Control circuit cutout device. 4. Terminal blocks, control wiring and control power buses. 5. Manual latch to retain circuit breaker in withdrawn position. 6. Side wall mounted sliding type secondary disconnects to facilitate inspection of mating of

contact from the front and easy accessibility for troubleshooting. Secondary disconnects using plug and socket arrangement with umbilical cord, as well as disconnects not visible for inspection, are not permitted.

7. Provision shall be made for closed door racking with a manual racking handle. Mechanical position indication shall be visible with door closed.

8. Racking mechanism shall be simple to install and operate. Racking mechanism using a chain to transmit motion from one side to the other side is not permitted. Provision for installing up to three padlocks shall be integral with the racking mechanism to assure positive position locking of the circuit breaker.

G. Each auxiliary cell shall include the following: a. Hinged front panel, suitable for relays and instruments b. Necessary terminal blocks, control wiring and control power buses c. Device markers.

H. Switchgear construction shall facilitate floor roll-out of circuit breakers in the lower cells. Guide channels shall be provided for smooth circuit breaker roll-in.

I. Each vertical section shall be approximately 36" width x 98.5" depth x 95.25" height.

J. The steel used in the structure and panels shall be chemically cleaned, hot phosphate treated, rinsed and oven-dried and shall be given an electrostatically applied coat of ANSI 61 polyester paint.

K. Low-voltage device panel located inside the circuit breaker or auxiliary cells shall be painted high-gloss white for better visibility and ease of maintenance.

L. Enclosure

1. Walk-in enclosure. Single-aisle design shall consist of indoor type circuit breakers and auxiliary cells located in weatherproof steel housing having an operating aisle space of sufficient size to permit withdrawal of the circuit breakers for inspection, test and maintenance. The following shall be included: a. Outdoor enclosure: Painted steel, weatherproof construction; integral structural

steel base frame with factory-applied asphalt undercoating; and equipped with the following features: 1.) Structural design and anchorage adequate to resist loads imposed by 140

M.P.H. wind 2.) Fluorescent aisle lights with low-temperature ballasts, controlled by three

way wall switches at each access door 3.) Space heaters in each vertical section, operating at 1h rated voltage, sized to

prevent condensation 4.) Aisle of sufficient width to permit circuit breaker withdrawal, disassembly and

servicing in the aisle


3. Internal wiring shall be carried in inter-unit wiring area, which protects the wires. The wires shall be bundled, tie-wrapped and secured to metal anchors. Wire ties with self sticking tape shall not be permitted.

2.5 VACUUM CIRCUIT BREAKERS

A. Vacuum circuit breakers: Drawout mounted units using three individual vacuum interrupters and including the following features: 1 . Circuit breaker design shall operate at rated voltage to interrupt fault current within its

rating within three cycles of trip initiation. 2. Contact-wear indicator shall be readily visible from the rear of the circuit breaker. 3. Four minimum spare auxiliary contacts shall be provided. Additional contacts shall be

provided on the cell wall as specified. 4. Operating mechanism shall be electrically charged, mechanically and electrically trip-free

and stored-energy operated. 5. Closing velocity of moving contacts shall be independent of both control voltage level and

operator. 6. Design of mechanism shall permit manual charging of mechanism. 7. Control power shall be 125 Vdc for closing and tripping. 8. The operating mechanism shall be front accessible so that it is not necessary to work

under the circuit breaker or tip it over in order to perform maintenance. 9. A single visual check, such as a contact erosion indicator, shall be sufficient to verify both

spring pressure and contact wear. The contact erosion indicator shall be identical across all circuit breaker ratings. Confusing maintenance procedures, such as separate contact erosion and wipe measurements, shall not be permitted.

10. Circuit breaker tripping provisions shall include shunt trip coil for tripping with protective relays, lockout relays, control switch or manual command signal from the relay. The circuit breaker shall include mechanical push button for manual tripping.

11. Circuit breaker closing provisions shall include close (spring release) coil for closing by electrical signal from control circuitry, control switch or manual command signal from the relay. The circuit breaker shall include mechanical push button for manual closing.

12. Current transfer path from the interrupter moving stem to the circuit breaker polemounted finger cluster shall be flexible copper laminations with long mechanical life. Brush, roller or wiping contacts shall not be permitted.

13. Vacuum interrupters and circuit breaker shall be manufactured and warranted by the same manufacturer.

14. Vacuum interrupter design shall limit the chopping currents to below 5 A to obviate the need for surge protection against switching transients during fault interruption for most loads. Surge limiters shall be provided for feeders to motors having locked rotor current of less than 600 A.

B. The circuit breakers shall be floor rollout that permits convenient insertion and withdrawal of the vacuum circuit breakers in the lower cells (of switchgear not on a raised pad) without the use of lift truck, ramp or dolly. Circuit breakers shall be installed in lower cells only. Upper cells are not to be used for circuit breakers.

C. Circuit breakers of equal ratings shall be interchangeable for the lower cells.

D. For 50 kA or lower ratings, the vacuum circuit breakers shall be designed to be used in switchgear cells of the same design and short-circuit rating but different voltage or continuous ratings, as long as the voltage and continuous current ratings of the circuit breaker shall be equal to or higher than required by the cell. 2,000 A and 3,000 A circuit breakers shall be designed to be used in 1200 A cells.

E. It shall be possible to test the circuit breaker in the TEST position inside the cell without the use of additional cables or couplers.

F. The switchgear manufacturer shall cycle each circuit breaker through at least 200 mechanical on-off operations as a part of routine production tests.


E. Verify operation of interlocks.

F. Perform power-frequency withstand voltage tests in accordance with ANSI/IEEE C37.20.2, clause 6.5.

3.5 WARRANTY

A. Equipment manufacturer shall warrant that all goods supplied are free of non-conformities in workmanship and materials for one year from date of initial operation, but not more than 18 months from date of shipment.

3.6 START-UP SERVICE

A. Switchgear manufacturer shall provide a factory-authorized service representative for a period of four days to train Owner's maintenance personnel in the following:

B. Procedures and schedules related to startup and shutdown, troubleshooting, servicing and preventive maintenance.

C. Review data in the instruction manuals.

D. Schedule training with Owner with at least three week's advance notice.

3. 7 FIELD SERVICE

A. Switchgear manufacturer's own field service office (same name as the manufacturer) shall be located not more than a three hour drive from the installation site.

END OF SECTION


ABB Bid Proposal Aubrey Silvey

Vero Beach - Substation 9 - Switchgear Replacement ABB CCP # 1502592880 - Vero Beach-Substation 9

Medium Voltage Air Insulated Metal-Clad Switchgear

It It ABB Inc.

Lake Mary, Florida USA

It llt

4/1/2015

Aubrey Silvey

Attention: Kevin Roa

Subject: Vero Beach - Substation 9 - Switchgear Replacement RFQ No. ABB CCP No. 1502592880 - Vero Beach-Substation 9, Rev. No. 0, Rev. Date: 8/3/2015

Dear; Kevin

In response to your request for quotation we are pleased to submit our proposal for Metal-Clad Switchgear as described herein. Our proposal is based on the drawings, specifications, and requirements of your request for quotation except as indicated by our proposal bill of material or clarifications in the technical and/or commercial sections of this proposal.

The opportunity to provide this equipment to Aubrey Silvey is greatly appreciated, and this offering is intended to meet your highest expectations.

We look forward to your consideration of this proposal, and will be pleased to answer any questions you may have. Please contact myself, if you require any additional information.

Best regards,

Mauricio Martinez Marketing Representative Ph: 407 732 2187 Fax: E-mail: [email protected]

This is lhe Property of ABB Inc. and contains Confidential information which must not be duplicated, used or disclosed other than expressly authorized by ABB Inc.

ABB Inc. Ph: 407-732-2000 655 Century Point Fax: 407-732-2346 Lake Mary, FL 32746 Website: ww.abb.com/mediumvoltage

mailto:[email protected]

Customer: Aubrey Silvey Project: Vero Beach - Substation 9 - Switchgear Replacement ABB CCP: 1502592880 - Vero Beach-Substation 9 Date: 4/1/2015 Rev.#3;8/3/2015

Commercial Offering

Page 3 of9

Commercial Offering

For

Aubrey Silvey

Vero Beach - Substation 9 - Switchgear Replacement

II This is the Property of ABB Inc. and contains ABB Inc. CONFIDENTIAL information which must not be 655 Century Point duplicated, used or disclosed other thanLake Mary, FL 327 46 llt

Ph: 407-732-2000 expressly authorized by ABB Inc.

Customer: Aubrey Silvey Commercial Offering Project: Vero Beach - Substation 9 - Switchgear Replacement ABB CCP: 1502592880 - Vero Beach-Substation 9 Date: 4/1/2015 Rev.# 3; 8/3/2015 Page 4 of9

Commercial Offering

Item List & Pricing Information

Rev. No.

Item No. Qty. Description Unit Price, US$

0 A01 1 Switchgear ABB type Advance Metal-Clad Switchgear Indoor, rated 15 kV, 2000 A, 25 kA, 3-phase 3-wire, 60 Hz, 95 kV BIL consisting of (6) cubicles with (5) ADVAC vacuum circuit breakers, complete with specified equipment per the attached bill of material.

215,330

0 A02 1 Accessories Accessories & Special Tools - please refer to item bill of material for detailed list and unit prices.

11, 146

0 A03 1 Spare parts Spare Parts - please refer to bill of material for detailed list and unit prices.

3,531

0 A04 1 Sheltered Aisle shipping - Transportation to Vero Beach 14,475

0 A05 1 Sheltered Aisle 78,730

0 A06 1 !NCO-Terms 2010 4,957

Total Net Price, US$ 328,169

ABB has carefully reviewed the provided specifications and drawings during the preparation of this proposal: however, items not explicitly stated in the attached Bill of Material are neither provided nor implied.

ABB Order Acceptance Procedure:

ABB will review the PO documents for conformance to the ABB quotation. Once mutually agreeable contract terms are reached, a contract start date will be established. All quoted lead-times will be based on this agreed contract start date.

To expedite order acceptance, please provide the following information on your purchase order documents:

Reference to ABB CCP # 1502592880 - Vero Beach-Substation 9 and revision level. Reference to the agreed terms and conditions and payment terms. Freight terms, "Ship To" address and required delivery date. E-mail address for the transmittal of drawings, and file. Requested warranty period (months/years). Taxable status - if Tax Exempt, please send certificate with PO documents.

ABB Inc. This is the Property of ABB Inc. and contains 655 Century Point II CONFIDENTIAL information which must not be Lake Mary, FL 32746 duplicated, used or disclosed other than Ph: 407-732-2000 expressly authorized by ABB Inc.


Delivery Schedule:

Contract drawings, information submittals, manufacturing, and shipment schedules will follow the outline below and are contingent on customer approval in the timeframe indicated:

Approval Drawings - Class I & II: 4 to 6 weeks after receipt of purchase order.

Customer drawing approval time: 2 weeks to keep order timeline on schedule.

Switchgear Ready for Shipment: 12 to 14 weeks after return of approved drawings and release to manufacture.

Total Typical Lead Time: 18-22 weeks** (with 2 week customer approval)

Total Accelerated Lead Time: 13-17 weeks with onboard customer approval: i.e. Webinar or at factory when drawings are available.

All customer provided information and requirements must be finalized at the time of purchase order placement. Revision to contract requirements may result in schedule changes or delays. All lead-times are subject to prior sale, please contact factory for actual lead-times at time of order placement.

Other Drawings/Documents Schedule:

Optional Class Ill Drawings: 4 to 6 weeks after return of Class I & II approval drawings.

Electronic Instruction Books: 2 weeks after shipment of switchgear.

As-Built (Final Record) Drawings: 2 to 4 weeks after shipment of switchgear.

Please refer to the Technical Offering for definitions of all ABB-supplied documentation.

Delays in Shipment:

Should the purchaser request that ABB delay shipment, once material is released and/or manufacturing has started, ABB will store such equipment, subject to the following conditions:

a) Purchaser shall issue a written request on purchaser's letterhead including the following information in b) through d).

b) Upon completion, the purchaser will allow ABB to issue an invoice for the equipment and process said invoice, within the payment terms of the purchase order, as if the equipment had actually shipped.

c) Purchaser agrees to assume title and ownership of the equipment on the date the invoice is issued. Warranty will start at time of ownership transfer.

d) Purchaser agrees to pay ABB applicable handling and storage fees until time of shipment. If shipment is delayed for more than 4 weeks, an additional fee will be assessed for inspection and cleaning of the equipment prior to shipment.

e) Prices are subject to escalation in the event of customer requested/caused delay at the rate of 1% per month, (or fraction there-of) and any additional storage or holding fees.

Project Specific Terms:

Factory Witness Testing:

ABB offer includes (FWT) factory witness test of equipment prior to shipment.

ABB Inc. This is the Property of ABB Inc. and contains 655 Century Point CONFIDENTIAL information which must not be Al 1111 Lake Mary, FL 327 46 duplicated, used or disclosed other than ,., 1919 Ph: 407-732-2000 expressly authorized by ABB Inc.


Equipment testing will be performed to ABB standard testing procedures. For additional details on factory

witness testing, please refer to technical offering.

Delivery Terms:

CPT (Carriage Paid To) Destination: Switchgear is loaded onto truck and shipped to named destination.

Offer does not include offloading of switchgear.

Or

OAP (Delivered at Place) Destination: Switchgear is loaded onto trucks and shipped to named

destination. Offer does not include offloading of switchgear.

Firm Pricing:

Prices offered are firm for the quoted delivery.

Taxes I Duties I Fees:

No Federal, state or local taxes, duties or fees of any kind are included in the above prices.

Terms of Payment:

ABB offer is 100% Net 30 Days after shipment and submittal of final contract documents.

Bid Validity:

This offering is valid until 5/8/2015 unless extended or terminated in writing by an authorized

representative of ABB.

Warranty:

ABB standard warranty offer is (12) months from date of initial operation, not to exceed (18) months from

date of shipment. Extended warranty provisions may be purchased prior to equipment shipment and may

be extended in 1-year increments for up to 5 additional years at the rate of 2% per year. To purchase

extended warranty period please refer to Item List & Pricing Information for details.

Changes in Scope of Supply:

Changes in scope of supply or delays caused by the Purchaser may also affect the project shipping

schedule. Should it become necessary to reschedule due to a purchaser-caused-delay, ABB will make

every effort to reschedule the project into the first available opening in our factory schedule based on

loading and available manufacturing slots. Any associated dates, including but not limited to schedule of

Liquidated Damages, will be adjusted accordingly.

Cancellation Schedule:

10% after order entry 20% after drawings issued for approval 45% after return of approval drawings or release to manufacture .

,e 75% after release of Bill of Material to Production

100% after start of fabrication

Service/Training: ABB can support our customers with hands-on factory authorized training for all their new installations. ABB Medium Voltage offers a hands-on training class for up to 10 technicians on-site to train them on the proper operation and safety requirements of their new switchgear. The duration and content of the class can be customized based on the experience and background of your technicians. The classes are led by highly skilled factory trained field service technicians and additional training courses are available based on customer needs, including preventative maintenance, complete refurbishment, relay coordination, etc. ABB will design the program around the customer requirements.

ABB Inc. This is the Property of ABB Inc. and contains 655 Century Point CONFIDENTIAL information which must not be It It Lake Mary, FL 32746 duplicated, used or disclosed other than Ph: 407-732-2000 expressly authorized by ABB Inc.


ABB offers installation and commissioning of all our products at competitive rates, utilizing our factory

trained service team. We work with our customers to determine which team is needed to support your

installation requirements and if this service is purchased, we will waive the fee for the one day hands-on

training mentioned above.

ABB also offers preventative maintenance at factory recommended intervals to increase the reliability and

service life of your new gear. Choosing an ABB PM program will allow ABB to extend the warranty on

your equipment up to 5 years and beyond.

Manufacturing locations:

ABB Inc. has more than 20 global locations for manufacturing ANSI and IEC Switchgear. Lake Mary,

Florida and San Luis Potosi, Mexico (SLP) are the two locations for the manufacture of ANSI designed MV

switchgear. Due to our multiple factory locations, ABB has the ability to maintain shorter lead times by

utilizing both factories. ABB San Luis Potosi, Mexico has been selected the primary facility for this order.

Terms and Conditions of Sale:

This offering is based on purchaser's acceptance of ABB Inc. Terms & Conditions of Sale, Form ABBGTC073101.

ABB Inc. This is the Property of ABB Inc. and contains 655 Century Point J~ It It CONFIDENTIAL information which must not be Lake Mary, FL 32746 duplicated, used or disclosed other than Jiil\ 1919 Ph: 407-732-2000 expressly authorized by ABB Inc.

Customer: Aubrey Silvey Commercial Offering

Project: Vero Beach - Substation 9 - Switchgear Replacement

ABB CCP: 1502592880 - Vero Beach-Substation 9

Date: 4/1/2015 Rev.# 3; 8/3/2015 Page 8 of9

Frequently Asked Questions

Medium Voltage Metal-Clad Switchgear

A ORGANIZATION

1. Parent Company . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ABB Ltd.

Affolternstrasse 54

Zurich, Switzerland

Phone: 4143317 7111

Fax: 41433174420

a) NYSE Listing Symbol ...... .... ......... .. ABB

b) Tl/El Number.................................. 13-2971634

c) Website.......................................... www.ABB.com

d) Years in Existence........................... >100 Years

2. U.S. Corporate Headquarters ................. ABB Inc.

12040 Regency Parkway

Suite 200

Cary, NC 27518

Phone: 01 919 856 2360

a) Form of Organization ...................... Corporation

b) State of Incorporation ..................... Delaware

c) Date of Incorporation ...................... November 10, 1980

d) Federal El/Tl Number..................... 36-3100018

e) SIC Code ....................................... 5063

3. Billing Location of Business .... ............. ... ABB Inc.

655 Century Point

Lake Mary, FL 327 46

Phone: 01 407 732 2000

Fax: 01 407 732 2346

a) Switchgear Management ......... ..... .. Roger Bailey, SVP and GM Robert Kowalik, ABB Lake Mary GM

b) Products . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . Medium Voltage Metal Clad Switchgear

B QUALITY

The ABB Quality Management System (QMS) is ISO 9001-2000 certified.

ABB Inc. This is the Property of ABB Inc. and contains 655 Century Point CONFIDENTIAL information which must not be Jl 1111

Lake Mary, FL 32746 JH\1919 duplicated, used or disclosed other than


http:www.ABB.com

Customer: Aubrey Silvey Commercial Offering Project: Vero Beach - Substation 9 - Switchgear Replacement ABB CCP: 1502592880 - Vero Beach-Substation 9 Date: 4/1/2015 Rev.#3;8/3/2015 Page 9 of9

C FINANCIAL

1. Sales 2010 31.6 Billion USO

2. Banking References ............................... JPMorgan Chase Audit Confirmation

P.O. Box 95520 Fort Worth, TX 76155-9200 Escalation Phone: 01 (225) 332 7731 Toll-free: 01 800 550 8509

Account323397883

3. Dun & Bradstreet ..... ..... ....... .... ... ....... .. .... 80-822-9041, ABB Inc., Corporate Level

D INSURANCE

1. Workers' Compensation .......................... ACE American Insurance Company and Employers' Liability April 1, 2011 - April 1, 2012

Policy#: SCF C4 6472391 Wisconsin Policy#: WLR C4 647238A All Other States

2. General Liability Insurance Company of Hanover

3. Automotive Liability Ace American Insurance Com April 1, 2011-April1, 2012 Policy# ISA HO 8634427

4. Casualty Broker Aon Risk Services, Inc. of MA

99 High St. 13th Fl.

Boston, MA 02110

[email protected] (Phone): 01 617 457 7713 (Fax): 016175422597

E SURETY

1. Surety Company

The Insurance Company of the State of Pennsylvania

175 Water Street

New York, N.Y. 10038

Attention: Waiman Yeung

Phone: 01 212 458 3767

2. Surety Broker AON Risk Services, Inc. of Pennsylvania

1650 Market Street - Suite 1000

Philadelphia, PA 19103

[email protected]

(Phone): 01215255 1879

(Fax): 01 205 255-1978

ABB Inc. This is the Property of ABB Inc. and contains 655 Century Point CONFIDENTIAL information which must not be AL It It Lake Mary, FL 32746 Jill\ duplicated, used or disclosed other than


mailto:[email protected]:[email protected]

Customer: Aubrey Silvey Project: Vero Beach - Substation 9 - Switchgear Replacement ABB CCP: 1502592880 - Vero Beach-Substation 9 Date: 4/1 /2015 Rev. # 3 ; 8/03/2015

Technical Offering

Page 1of6

Technical Offering

For

Aubrey Silvey


ABB Inc. This is the Property of ABB Inc. and contains 655 Century Point Jl 1111 CONFIDENTIAL information which must not be Lake Mary, FL 32746 duplicated, used or disclosed other than 111\.1919 Ph: 407-732-2000 expressly authorized by ABB Inc.

Customer: Aubrey Silvey Technical Offering Project: Vero Beach - Substation 9 - Switchgear Replacement ABB CCP: 1502592880 - Vero Beach-Substation 9 Date: 4/1/2015 Rev.# 3; 8/03/2015 Page 2 of 6

Technical Offering

ABB Comments and/or Clarifications to Customer's Specification(s):

Item 1.5- B Circuit breakers shall be shipped inside their respective cells.

ABB confirms that the breakers are always shipped loose in order to prevent any damage to the breakers and to the breaker cubicle during transportation due vibrations.

Item 1.5- D Bus bars with associated hardware for connections between shipping groups shall be shipped inside one of the units in which shall be installed.

Normally bus bars are shipped separately in specific crate. This is done to secure them properly for transportation and avoid any damage in the insulation

Item 2.3- I Each vertical section shall be approximately 36" width x 98.5" depth x 95.25" height.

Correct dimensions are 36" width x 92" depth x 95" height.

Item 2.5-D For 50 kA or lower ratings, the vacuum circuit breakers shall be designed to be used in switchgear cells of the same design and short-circuit rating but different voltage or continuous ratings, as long as the voltage and continuous current ratings of the circuit breaker shall be equal to or higher than required by the cell. 2,000 A and 3,000 A circuit breakers shall be designed to be used in 1200 A cells

ABB breaker cubicles have an interference plate which avoid breakers of different capacities to be inserted in other cells.

Item 2.5-F The switchgear manufacturer shall cycle each circuit breaker through at least 200 mechanical on-off operations as a part of routine production tests.

Breakers are normally operated 20 to 30 times during production tests.

Part 3- Execution

ABB is not considering any work, installation, assembly, supervision, adjusting, field quality control, startup, commissioning or service at site.

All works will be coordinated and commercially agreed during project execution according to the service rates. For reference, the service rates sheet is attached to this proposal.

ABB Inc. This is the Property of ABB Inc. and contains 655 Century Point At. 1111 CONFIDENTIAL information which must not be Lake Mary, FL 32746 Ill\ duplicated, used or disclosed other than Ph: 407-732-2000 expressly authorized by ABB Inc.


Technical Offering

Product Technical Description:

Switchgear Frame Construction:

Advance metal-clad switchgear is comprised of freestanding vertical frames. Each frame is of modular

construction and fabricated primarily from 14-gauge galvanized sheet metal. All galvanized sheet metal

sections will be unpainted. Sections thicker than 14 gauge and welded components are made of hot

rolled steel that has been phosphate treated and finished with baked-on corrosion resistant epoxy enamel

paint. The standard color for painted items is ANSI #61, light gray. Hem bending on all galvanized panels

provides superior edge protection for operational personnel and are used throughout the construction to

enhance strength and rigidity.

Ground Bus:

The switchgear enclosure is grounded to a solid % x 2 inch, tin-plated copper bus that extends through

the entire length of the switchgear. The ground bus is accessible in the cable module, and has predrilled

connection points in each section for instrument grounding. It also extends into the circuit breaker

module where it engages the ground contacts on the circuit breaker chassis.

Circuit Breaker Racking System:

The switchgear is designed with a three position (connected-test-disconnected) closed-door racking

system for all circuit breakers, and includes a patented, fully automatic secondary disconnect system.

The racking system is integral to the circuit breaker. All moving parts remain with the circuit breaker when

withdrawn from the module. Maintenance may be safely performed away from energized primary and

secondary (control) circuits. The circuit breaker/enclosure system will include all necessary interlocks to

assure proper sequencing and safe operation in accordance with ANSI standards. It shall be possible to

rack the breaker into test or connected positions with the door closed, to maintain the integrity of arc

resistant construction during racking. During racking, the breaker will autom~tically open and close cell

mounted safety shutters to cover stationary primary contacts when the breaker is not in the connected

position. The racking system can be padlocked in the disconnected, test and connected positions to

prevent unauthorized insertion or removal. Shutters can also be locked in the closed position (padlocks

supplied by others).

Circuit Breaker:

ABB type ADVAC and AMVAC circuit breakers are designed specifically for use with the Advance

switchgear.

ADVAC is a 3-pole draw out type vacuum circuit breaker. It uses a simple, front-accessible stored

energy operating mechanism designed specifically for use with vacuum technology. This provides the

benefits of dependable vacuum interrupters with advanced contact design and proven reliability, without

the complexity of mechanisms and linkages found in previous generation circuit breakers. Control

features of the ADVAC breaker emphasize convenience, maintainability and flexibility. Charge, close

and trip functions can be accomplished both electrically and manually. All manual functions can be

performed with great ease at the front of the breaker.

The AMVAC is truly the next generation in medium voltage vacuum technology. With the AMVAC,

ABB is the first to marry the unique requirements of vacuum interrupter technology to a stored energy

mechanism designed to exploit those capabilities. Using a flux-shifting device with integral permanent

magnets, the AMVAC mechanism has just seven moving parts. Vacuum interrupters are embedded in

a proprietary epoxy material achieving excellent dielectric and thermal capabilities. Like the ADVAC

breaker, the AMVAC eliminates the need for mechanism operated cell switches by packaging all

auxiliary control contacts on the circuit breaker. These are just a few of the features that mark a

ABB Inc. This is the Property of ABB Inc. and contains 655 Century Point CONFIDENTIAL information which must not be Al 1111 Lake Mary, FL 32746 Ill\ duplicated, used or disclosed other than Ph: 407-732-2000 expressly authorized by ABB Inc.


departure from the conventional stored energy breaker and introduce new capabilities and features for

modern power systems.

ADVAC & AMVAC circuit breakers include eight auxiliary switch contacts (4"a", 3"b") mounted on

board and wired through the automatic secondary disconnect. Nine extra on-board contacts for a total of

17 auxiliary contacts (9 "a", 8 "b") are available also wired through an automatic secondary disconnect.

Since all auxiliary contacts are on-board (located directly behind the front cover of the breaker), they are

automatic, operating with the breaker in either test or connected positions.

These breakers are intended for use as a general purpose device in accordance with applicable ANSI

standards. Circuit breakers of the same type, rating and control voltage are electrically and mechanically

interchangeable. The circuit breaker enclosure has an interference block to prevent the insertion of

improperly rated breakers. Breakers and ground and test devices rated at 2000 amp are physically

interchangeable in 1200 amp compartments for economy of spare devices.

Main Bus:

Bus bars, including bends, are cold formed hard-drawn 98% IACS solid copper with full round edges and

epoxy insulated except at connection joints. The standard connection joints are silver-plated and tin

plating is optional. Connection joints, taps, and splices are covered with low power factor air filled vinyl

boots. The covers are easily removable for field inspection. Bus bar connections are mechanically

secured via NEMA hole pattern with SAE Grade 5 reusable fasteners.

Bus supports and insulation materials are flame resistant, track resistant and non-hygroscopic. Supports

for 1200 A and 2000 A systems are made of pre-molded glass filled polyester. Glass filled polyester is

particularly adaptable to modern switchgear. This material exhibits outstanding electrical properties, and

is exceptionally strong and durable even under extreme environmental conditions. Supports for 3000 A

systems are made of porcelain on track resistant polyester. Standoff insulator supports will be pre

molded glass filled polyester, porcelain insulators are optional.

The complete primary bus system was designed and fully tested in accordance with rigorous ANSI

requirements, assuring dependable performance over a long life. Each primary compartment is subjected

to high voltage production tests as a final assurance of a quality product.

Instrument Transformers:

All primary modules for auxiliary equipment (potential transformers and control power transformers) are

equipped with similar technology as the circuit breaker cells. Consequent design with closed door racking

system and automatic secondary disconnect allow for operator familiarity and improved safety. The cell

interface uses the same accessories as the circuit breaker module. Secondary contacts

engage/disengage automatically and interlocks ensure proper operation where applicable. In addition, all

primary auxiliary equipment utilizes arc quenching Delrin technology. A Delrin sleeve around a

conductor probe is inserted into a Delrin receptacle with recessed contacts. During load break only a

very small isolating gap is required between the sleeve and receptacle to contain the arc and extinguish it

safely.

Current transformers can be mounted on both line and load primary bushings behind the shutter.

Bushings can accommodate up to four standard accuracy current transformers per phase, two per phase

for high accuracy current transformers.

Manufacturing Locations:

ABB Inc. has more than 20 global locations for manufacturing ANSI and IEC Switchgear. Lake Mary,

Florida and San Luis Potosi, Mexico (SLP) are the two locations for the manufacture of ANSI designed

MV switchgear. Due to our multiple factory locations, ABB has the ability to maintain shorter lead times by

utilizing both factories. San Luis Potosi, Mexico is designed to be the primary manufacturing location.

ABB Inc. This is the Property of ABB Inc. and contains 655 Century Point CONFIDENTIAL information which must not be Jl 1111 Lake Mary, FL 32746 .I'll\ 1919 duplicated, used or disclosed other than Ph: 407-732-2000 expressly authorized by ABB Inc.

Customer: Aubrey Silvey Technical Offering Project: Vero Beach - Substation 9 - Switchgear Replacement ABB CCP: 1502592880 - Vero Beach-Substation 9 Date: 4/1/2015 Rev. #3; 8/03/2015 Page 5 of 6

Relay Settings and Coordination Studies:

Relay coordination and system studies, relay settings, arc flash studies, and CT burden calculations are

not included in this quotation.

Production Testing & Inspection:

ABB will perform production test of the switchgear in accordance with ANSI C37.20.2 Section 6.3 prior to

shipment.

Level 1 - Visual & Mechanical Factory Inspection includes the following:

A Visual review/inspection only of the equipment.

1. No energization of primary busses or secondary controls B. Mechanical operation of all PT, CPT and Fuse roll-out assemblies. C. Racking circuit breakers in and out of cells for fit check tests.

D. Verifying completeness of order.

E. Review of documentation.

F. Rate provides for up to 3 people in attendance for 1 day.

Level 2 - Factory Witness Testing (FWT) includes the following:

A Includes all items listed in Level 1 - Visual & Mechanical Factory Inspection.

B. Witness of DC and/or AC control power applied to secondary controls in order to perform basic breaker close and trip operations per control schematic diagrams.

C. Witness of current applied to secondary of current transformer circuits (when applicable) to see basic functional test of metering and relaying circuits as per the AC elementary (3-line) diagrams.

D. Witness of voltage applied to secondary of potential (voltage) transformer circuits (when

applicable) to see basic functional test of the metering and relaying circuits as per the AC

elementary (3-line) diagrams.

E. Rate provides for up to 3 people in attendance, for the time period stated in the bill of material. Additional people may attend at a cost of $500 each per day.

F. Rate does not include hotel, transportation, travel, airfare, food or other related costs.

ABB Supplied Documentation:

ABB Class I approval drawings will consist of a system (SLD) single line drawing, (FV) front view, (FP) floor plan, (SV) section view, (NP) nameplate information drawing, and (EBOM) electrical bill of material.

ABB Class II approval drawings will consist of 3-line elementary diagrams and breaker control schematic diagrams.

ABB Class Ill approval drawings will consist of (ICD) interconnection and (CD) connection wiring diagrams.

Record drawings will consist of class I, II & Ill with all customer comments incorporated and submitted at prior to start of manufacturing.

Final "As-Built" record drawings will consist of class I, II & Ill with all manufacturing comments and/or corrections incorporated.

Drawings will indicate all equipment, but only such equipment, as is actually in the switchgear scope of supply. All user connection and interface points will be clearly marked, including primary and secondary

ABB Inc. This is the Property of ABB Inc. and contains II655 Century Point CONFIDENTIAL information which must not be duplicated, used or disclosed other than Lake Mary, FL 327 46 Ph: 407-732-2000 expressly authorized by ABB Inc.


cable entrances and connection points; installation details; and inter-frame assembly and connection details for shipping splits.

Drawings will be professionally prepared on AUTODESK AutoCAD Mechanical 2014, SolidWorks Premium 2014, e-Plan Electric P8, Adobe Reader XI, MS-Word and MS-Excel to the maximum extent practical, and will be provided to the customer on paper and/or electronically on a CD or by e-mail.

Instruction books will be provided with necessary information for receiving, handling, storage, installation, operation and maintenance. The instruction book will assist in identification and ordering of recommended spare parts.

Common Definitions:

Class I Approval Drawings - Provide the physical aspects of the equipment. They consist of a system single line drawing, front view, floor plan, nameplate drawing, and electrical bill of material.

Class II Approval Drawings - Provide the electrical aspects of the equipment. They consist of threephase elementary and schematic diagrams.

Class Ill Drawings - Consists of interconnection and connection diagrams.

Instruction Book - Will contain information for receiving, handling, storage, installation operation and maintenance. Instruction books are provided in electronic format unless otherwise specified.

As-Built Drawings - a final submittal of class I, II and Ill drawings incorporating all changes found during the manufacturing process of the equipment (aka - final record drawings)

Advance Switchgear - ABB's medium voltage non-arc resistant metal-clad switchgear offering. Meets ANSI standard C37.20.2

Arc Flash Mitigation Relay - ABB offers a system of solid state relays that can detect and respond to an arc flash incident inside of electrical gear in less than 2.5 milliseconds. Used to trip a breaker to interrupt the arc and minimize total arc flash energy and reduce equipment and personnel damage.

Freight Allowed - Freight is included in the total price

Standard Commercial Packaging - For ABB Switchgear, this indicates it is packed for open top trailer truck shipment. We require that the gear be stored indoors after receipt by customer.

ABB Inc. This is the Property of ABB Inc. and contains 655 Century Point 1111 CONFIDENTIAL information which must not be Lake Mary, FL 32746 duplicated, used or disclosed other than Ph: 407-732-2000 expressly authorized by ABB Inc.

Item -A01

Bill of Material

For

Aubrey Silvey


Switchgear

Page 1 of20

ltem-A01 Bill of Material

Scope of Supply:

Advance Metal-Clad Switchgear enclosure, rated 15 kV, 2000 A, 25 kA, 3-phase 3-wire, 60 Hz, 95 kV BIL with required and related capabilities in accordance with industry standards referenced in ANSI & IEEE.

Page 2 of20

ltem-A01 Bill of Material Switchgear

15 kV Metal-Clad Switchgear

Switchgear shall be designed and manufactured in accordance with the latest published standards of ANSI, NEMA, and IEEE.

Product Name Arc Resistant Enclosure Type Exterior Finish Interior Finish Seismic Rating Bus System Voltage Phase Frequency Main Bus Ampacity Bus Bracing Bus Insulation Bus Supports Bus Material Ground Bus Wiring AC Control Bus

DC Control Bus

Charging Voltage Closing Voltage Tripping Voltage Control Circuits

Current Transformer Circuits

Terminal Blocks Wiring Practice Spare Terminal Blocks Control Wire Lugs Wire Identification

Additional Features:

Advance No

Indoor ANSI# 61, Light gray enamel Unpainted, highly reflective galvanized IBC-2006, CBC-2007, ASCE 7-05, Ss=3.0g, SITE CLASS D, z/h=1.0, IP=1.0

15 kV 3-phase 3-wire 60 Hz 2000A 25 kA Fluidized bed baked-on epoxy with vinyl boots over joints Flame retardant track resistance pre-molded glass polyester Copper with silver plated joints W' x 2", solid copper, continuous throughout lineup

40 amps, 1-ph 3-wire circuit with #8 AWG connected to power terminal blocks 40 amps, 2-wire circuit with #8 AWG connected to power terminal blocks

125 V DC 125 V DC 125 V DC All control wire is #14 AWG minimum, multi-stranded extra-flexible, SIS 600 V flame retardant wire All CT circuits #12 AWG, multi-stranded extra-flexible, SIS 600-volt flame retardant wire UL-rated, 600 V, 30 A, 35 mm DIN-rail mount barrier type terminal block For control circuits a maximum of two wires per terminal point 20% additional terminal blocks per frame Vinyl Insulated control wire terminals Slip-on destination type wire markers, white with black letters

1 Level 2 - Factory Witness Test (FWT), 3-people for# of days 3 O&M Manuals, 3-ring binder, with project drawings 1 UL Listed and Labeled

5 Cell Modification - Roll On The Floor ADVAC Breaker 5 Breaker Modification, Casters for Floor Rolling

Page 3 of20

ltem-A01 Cubicle 01 CPT consists of:

PT COM PT

CZZ> Cl!]

PT COMPT

CZZ>

= INSTCOMPT

CPTCOMPT

0 =

-~~--~-r-,

INST COMPT

VENT CHAMBER

\ \

\ )

I A I I

I B: I

I c:

I

) I

I

_ _J

LINE SIDE

UN~ rv.7>SIDE ~s-p;

CONN ADJ FRM.

Compartment A: 1 PT Assembly, Drawout, 15kV, Wye-Wye connection 3 Potential Transformer, ABB type VIZ-11, 8400-120V, Line-Grd 3 PT Primary Fuse, Type 15CLPT-.5, 11-1/2" Clip Centers

Compartment B: 1 PT Assembly, Drawout, 15kV, Line to Line connection 1 Potential Transformer, ABB type VIZ-11, 14400-120V, Line-Line 2 PT Primary Fuse, Type 15CLPT-.5, 11-1/2" Clip Centers

Compartment D: 1 CPT Drawout Truck Assembly, 15kVA max, single phase 1 Control Power Transformer, ABB type CPT, 15kVA, 1ph, 13800-120/240V, 95kV BIL 2 CPT Primary Fuse, SE, 15.SkV, Size "C", 15" centers 1 CPT Secondary, MCCB, 90A, 2-pole, 240VAC

Cubicle: 1 M/C Base Frame, Auxiliary - extra depth 1 Frame Adder - Indoor Gasketed 4 Door Stop Assembly 1 Kirk Key Interlock, Type F, LO, single lock 1 Multi-Point Latch, Hinged Door Adder - 19" 3 Gasketed Hinge Panel Adder - 19" high 1 Gasketed Hinge Panel Adder - 38" high 1 End Panel Assembly - extra depth 1 Rear Panels, Split Bolted w/ handles & Air Filters 1 Ground Cable Lugs, compression type, #4/0 AWG 1 DC Control Bus, 40A 2-wire 1 AC Control Bus, 40A 1 ph 3-wire

Page 4 of20

1 DC Control Bus, MCCB, 40A 250VDC 2-pole 1 Molded Case Circuit Breaker, 40A 22kA 480V 3-pole 1 Strip Heater Circuit, Total 300 Watts applied at 1/2 voltage 1 Heater Circuit Protection, MCCB, 15A 120VAC 1-pole 10kA 1 Thermostat, +32 to 140 deg F, SPOT, 1 OA I 250Vac (Dev. 23) 1 20% Spare Terminal Blocks 1 Wired to Terminal Block, unused relay contacts 1 Wire Markers, white sleeve with black typed letters 1 Ground Strap across Inst Door Hinge, #14 AWG bare wire

AC Voltmeter, Swbd case, 120Vac, 1 % accuracy Voltmeter Switch, knurled handle (wye-wye)

Additional Components: 1 SEL relay# 3530HBODX211 OXXXXXX (Key 5613) 1 Auxiliary Current Transformer, single-ratio, T50 accuracy

Page 5 of20

ltem-A01Cubicle02 Main consists of:

111111111111111111111111111111111111111111111

INSTCOMPT INST COMPT

VENT CHAMBER

2000A

0 I~! - GND

Compartment D:

f

v

2000A ~

L

1

1 1 2 1

Advac M4 Circuit Breaker, Drawout Element, 15kV, 2000A, 25kA Breaker Auxiliary Switch, 16-pole (9a, 7b) Circuit Breaker Production Test Reports Certificate of Conformance Breaker Secondary Disconnect Assembly - dual plug - wired to terminal block (52H) TOC Switch Assembly, 16-pole, (8) "a" & (8) "b" contacts Fuse Holders, USCC, pull-type finger safe, 600Vac I 250Vdc, 30A, 2-pole Padlock Provisions - Hinged Panel

3 Current Transformer, ABB type SAB-1, 1200-5A single-ratio, C200 accuracy

Breaker Control Switch, pistol-grip, (1 )C & (1 )T

2 Indicating Lamp Assy w/ LED Bulb & color cap

Compartment E:

3 Current Transformer, ABB type SAB-1, 1200-SA single-ratio, C200 accuracy

Cubicle: 1 M/C Base Frame, 1-high, 2kAF Main or Feeder - extra depth 1 Frame Adder - Indoor Gasketed 2 Door Stop Assembly 1 Breaker Interlock Assembly - padlocking 1 Multi-Point Latch, Hinged Door Adder - 57'' 1 Gasketed Hinge Panel Adder - 38" high 1 Gasketed Hinge Panel Adder - 57" high 1 Riser to Bus Duct, 2000A from breaker (Pos. "B") top entry

Page 6 of20

1 1 1 1 1 1 1 1 1 1 1

Rear Panels, Split Bolted w/ handles & Air Filters DC Control Bus, 40A 2-wire AC Control Bus, 40A 1 ph 3-wire Control Interconnect - Bus Differential Scheme Strip Heater Circuit, Total 300 Watts applied at 1/2 voltage Heater Circuit Protection, MCCB, 15A 120VAC 1-pole 10kA Thermostat, +32 to 140 deg F, SPOT, 10A I 250Vac (Dev. 23) 20% Spare Terminal Blocks Wired to Terminal Block, unused relay contacts Wire Markers, white sleeve with black typed letters Ground Strap across Inst Door Hinge, #14 AWG bare wire

(86) Lockout Relay, ES - LOR, manual-reset, 4-deck (8)NO, (8)NC

Relay, Auxiliary, AE type P, 125Vdc, 10A, (4) NO convertible contacts

SHARK 200, Multi-Power Meter, (V1 ), 120Vac 5A 60hZ, 110 Slot 1 & 2 =X

1 1

AC Ammeter, Swbd case, 5A, 1 % accuracy Ammeter Switch, knurled handle, Off-1-2-3, end of line

2 Test Switch, ABB type FT-1, 10-pole

Additional Components:

1 SEL relay# 0351S6XHB3A5461(Key7058)

1 SEL relay# 0587ZOX325H12XX (Key 7866)

Page 7 of20

ltem-A01 Cubicle 03 Feeder consists of:

INSTCOMPT INST COMPT

VENT CHAMBER

I 0v 1200A

! A

1200A

0 [@7'

Compartment D: 1 Advac M4 Circuit Breaker, Drawout Element, 15kV, 1200A, 25kA

Breaker Auxiliary Switch, 16-pole (9a, 7b) Circuit Breaker Production Test Reports Certificate of Conformance

1 Breaker Secondary Disconnect Assembly - dual plug - wired to terminal block 1 (52H) TOC Switch Assembly, 16-pole, (8) "a" & (8) "b" contacts 2 Fuse Holders, USCC, pull-type finger safe, 600Vac I 250Vdc, 30A, 2-pole 1 Padlock Provisions - Hinged Panel 1 Cable Lug Boot, 3-ph, 1200A 1 Cable Support Assembly

1 Surge Arrester, Intermediate Class, ABB type XPI, 18kV, 15.3kV MCOV (set of 3)


2 Indicating Lamp Assy w/ LED Bulb &color cap

Compartment E:


Cubicle:

1 M/C Base Frame, 1-high, 1.2kAF Main or Feeder - extra depth

1 Frame Adder - Indoor Gasketed

2 Door Stop Assembly

1 Breaker Interlock Assembly - padlocking

1 Multi-Point Latch, Hinged Door Adder - 57"

1 Gasketed Hinge Panel Adder - 38" high

1 Gasketed Hinge Panel Adder - 57" high

Page 8 of20

1 Rear Panels, Split Bolted w/ handles &Air Filters 1 Bus Riser to Lug Pad from breaker, bottom entry - 1200A 1 DC Control Bus, 40A 2-wire 1 AC Control Bus, 40A 1 ph 3-wire 1 Control Interconnect - Bus Differential Scheme 1 Strip Heater Circuit, Total 300 Watts applied at 1/2 voltage 1 Heater Circuit Protection, MCCB, 15A 120VAC 1-pole 10kA 1 Thermostat, +32 to 140 deg F, SPOT, 10A I 250Vac (Dev. 23) 1 20% Spare Terminal Blocks 1 Wired to Terminal Block, unused relay contacts 1 Wire Markers, white sleeve with black typed letters 1 Ground Strap across Inst Door Hinge, #14 AWG bare wire

1 Relay, Auxiliary, AE type P, 125Vdc, 10A, (4) NO convertible contacts

SHARK 200, Multi-Power Meter, (V1 ), 120Vac 5A 60hZ, 1/0 Slot 1 & 2 =X

AC Ammeter, Swbd case, 5A, 1 % accuracy

Test Switch, ABB type FT-1, 10-pole

Additional Components: 1 SEL relay# 0351S6XHB3A54X1 (Key 7534)

Page 9 of20


INST COMPT

VENT CHAMBER

INSTCOMPT

Iv 1200A G

! A

1200A

0 @P;;='



1 Breaker Secondary Disconnect Assembly - dual plug - wired to terminal block 1 (52H) TOG Switch Assembly, 16-pole, (8) "a" & (8) "b" contacts 2 Fuse Holders, USCG, pull-type finger safe, 600Vac I 250Vdc, 30A, 2-pole 1 Padlock Provisions - Hinged Panel 1 Cable Lug Boot, 3-ph, 1200A 1 Cable Support Assembly

Surge Arrester, Intermediate Class, ABB type XPI, 18kV, 15.3kV MCOV (set of 3)

Breaker Control Switch, pistol-grip, (1)C & (1)T


Compartment E: 3 Current Transformer, ABB type SAB-1, 400-5A single-ratio, C100 accuracy

Cubicle: 1 MIC Base Frame, 1-high, 1.2kAF Main or Feeder - extra depth 1 Frame Adder - Indoor Gasketed 2 Door Stop Assembly 1 Breaker Interlock Assembly- padlocking 1 Multi-Point Latch, Hinged Door Adder - 57" 1 Gasketed Hinge Panel Adder - 38" high 1 Gasketed Hinge Panel Adder - 57'' high

Page 10 of20

1 Rear Panels, Split Bolted w/ handles & Air Filters 1 Bus Riser to Lug Pad from breaker, bottom entry - 1200A 1 DC Control Bus, 40A 2-wire 1 AC Control Bus, 40A 1 ph 3-wire 1 Control Interconnect - Bus Differential Scheme 1 Strip Heater Circuit, Total 300 Watts applied at 1/2 voltage 1 Heater Circuit Protection, MCCB, 15A 120VAC 1-pole 10kA 1 Thermostat, +32 to 140 deg F, SPOT, 10A I 250Vac (Dev. 23) 1 20% Spare Terminal Blocks 1 Wired to Terminal Block, unused relay contacts 1 Wire Markers, white sleeve with black typed letters 1 Ground Strap across Inst Door Hinge, #14 AWG bare wire


SHARK 200, Multi-Power Meter, (V1 ), 120Vac 5A 60hZ, 110 Slot 1 & 2 =X

AC Ammeter, Swbd case, 5A, 1% accuracy



1 SEL relay# 0351S6XHB3A54X1(Key7534)

Page 11 of20


INSTCOMPT

1200A

0

~

INST COMPT

VENT CHAMBER

I

v

1200A G

! A



1 Breaker Secondary Disconnect Assembly - dual plug - wired to terminal block 1 (52H) TOC Switch Assembly, 16-pole, (8) "a" & (8) "b" contacts 2 Fuse Holders, USCG, pull-type finger safe, 600Vac I 250Vdc, 30A, 2-pole 1 Padlock Provisions - Hinged Panel 1 Cable Lug Boot, 3-ph, 1200A 1 Cable Support Assembly

Surge Arrester, Intermediate Class, ABB type XPI, 18kV, 15.3kV MCOV (set of 3)



Compartment E:


Cubicle:

1 M/C Base Frame, 1-high, 1.2kAF Main or Feeder - extra depth

1 2 1 1 1 1

Frame Adder - Indoor Gasketed Door Stop Assembly Breaker Interlock Assembly - padlocking Multi-Point Latch, Hinged Door Adder - 57'' Gasketed Hinge Panel Adder - 38" high Gasketed Hinge Panel Adder - 57" high

Page 12 of20

1 Rear Panels, Split Bolted w/ handles &Air Filters 1 Bus Riser to Lug Pad from breaker, bottom entry - 1200A 1 DC Control Bus, 40A 2-wire 1 AC Control Bus, 40A 1 ph 3-wire 1 Control Interconnect - Bus Differential Scheme 1 Strip Heater Circuit, Total 300 Watts applied at 1/2 voltage 1 Heater Circuit Protection, MCCB, 15A 120VAC 1-pole 10kA 1 Thermostat, +32 to 140 deg F, SPOT, 10A / 250Vac (Dev. 23) 1 20% Spare Terminal Blocks 1 Wired to Terminal Block, unused relay contacts 1 Wire Markers, white sleeve with black typed letters 1 Ground Strap across Inst Door Hinge, #14 AWG bare wire

1 Relay, Auxiliary, AE type P, 125Vdc, 10A, (4) NO convertible contacts

1 SHARK 200, Multi-Power Meter, (V1 ), 120Vac 5A 60hZ, 1/0 Slot 1 & 2 =X

AC Ammeter, Swbd case, 5A, 1% accuracy



1 SEL relay# 0351S6XHB3A5461 (Key 7058)

Page 13 of20


lllllllllllllllllllllllllllllllllllllllllllll INST COMPT

2000A

0 ~l~I

INST COMPT

VENT CHAMBER

-GNO

Compartment D: 1

1 1 2 1

Advac M4 Circuit Breaker, Drawout Element, 15kV, 2000A, 25kA Breaker Auxiliary Switch, 16-pole (9a, 7b) Circuit Breaker Production Test Reports Certificate of Conformance Breaker Secondary Disconnect Assembly - dual plug - wired to terminal block (52H) TOC Switch Assembly, 16-pole, (8) "a" & (8) "b" contacts Fuse Holders, USCC, pull-type finger safe, 600Vac I 250Vdc, 30A, 2-pole Padlock Provisions - Hinged Panel




Compartment E:

3 Current Transformer, ABB type SAB-1, 2000-5A multi-ratio, C200 accuracy

Cubicle: 1 M/C Base Frame, 1-high, 2kAF Main or Feeder - extra depth 1 Frame Adder - Indoor Gasketed 2 Door Stop Assembly 1 Breaker Interlock Assembly - padlocking 1 Multi-Point Latch, Hinged Door Adder - 57" 1 Gasketed Hinge Panel Adder - 38" high 1 Gasketed Hinge Panel Adder - 57" high 1 End Panel Assembly - extra depth 1 Riser to Bus Duct, 2000A from breaker (Pos. "B") top entry

Page 14 of20

1 Rear Panels, Split Bolted w/ handles & Air Filters 1 Ground Cable Lugs, compression type, #4/0 AWG 1 DC Control Bus, 40A 2-wire 1 AC Control Bus, 40A 1 ph 3-wire 1 Control Interconnect - Bus Differential Scheme 1 Strip Heater Circuit, Total 300 Watts applied at 1/2 voltage 1 Heater Circuit Protection, MCCB, 15A 120VAC 1-pole 10kA 1 Thermostat, +32 to 140 deg F, SPOT, 10A I 250Vac (Dev. 23) 1 20% Spare Terminal Blocks 1 Wired to Terminal Block, unused relay contacts 1 Wire Markers, white sleeve with black typed letters 1 Ground Strap across Inst Door Hinge, #14 AWG bare wire


SHARK 200, Multi-Power Meter, (V1 ), 120Vac 5A 60hZ, 1/0 Slot 1 &2 =X



1 SEL relay# 3530HBODX2110XXXXXX (Key 5613)

Page 15 of20

ltem-A02 Bill of Material Accessories

Switchgear ACCESSORIES & SPECIAL TOOLS

The following list of accessories and special tools are intended for use with ABB type Advance Metal-Clad Switchgear and ADVAC circuit breaker(s) to conduct operational and maintenance procedures of the equipment.

ltem-A02

Listed are the accessories and tools included and/or specified.

Qty 1 1 1 1

Description ADVAC Breaker Accessory Kit CB Test Jumper, dual plug CB Test Station, dual plug (wall Electric Racking Device, ABB S

Unit Price. US$ $132.00 $280.00

mounted) $834.00 martRack, 120Vac w/ 25ft cord$9,900.00

Extended Price, US$ $132.00 $280.00 $834.00

$9,900.00

Total Line Item Net Price, US$ $11,146.00

NOTES: 1. Unit quantities are subject to change based on Customer and/or Project requirements. 2. Accessories & Special Tools unit prices are valid only if purchased with switchgear product.

Page 16 of20

ltem-A03 Bill of Material Spare parts

SPARE PARTS

The following list of spare parts are intended for use with ABB type Advance Metal-Clad Switchgear and

ADVACcircuit breaker(s) to maintain operational performance of the equipment.

ltem-A03

Listed are the spare parts recommended and/or specified.

Unit Extended Q1Y Description Price. US$ Price. US$ 1 Lubricant, NO-OX-ID (1-pint can) $50.00 $50.00 1 Lubricant, Anderol 757 (1-lb can) $75.00 $75.00 1 Touch-Up Paint, 12 oz can, ANSI# 61 $30.00 $30.00 1 Test Plug, ABB type FT-1, current circuits $345.00 $345.00 1 Test Plug, ABB type FT-1, potential circuits $282.00 $282.00 1 Spare Indicating Lamp Assy w/ LED Bulb & color cap $39.00 $39.00 1 Spare Lamp Bulb, LED $22.00 $22.00 6 Spare Fuses, Breaker Control, 250VDC (box of 10) $65.00 $390.00 6 Spare PT Secondary Fuse, 250VAC (box of 10) $50.00 $300.00 6 Spare PT Primary Fuse, CLE-PT 8.25kV or 15kV $145.00 $870.00 6 Spare CPT Primary Fuse, EJ0-1, 15kV (up to 15kva CPT) $188.00 $1,128.00

Total line Item Net Price, US$ $3,531.00

NOTES: 1. Unit quantities are subject to change based on Customer and/or Project requirements. 2. Spare Parts unit prices are valid only through project execution.

Page 17 of20

ltem-A04 & AOS Bill of Material Sheltered Aisle shipping & Sheltered aisle

Major Resale

The following Sheltered Aisle & Sheltered aisle shipping

ltem-A04 & AOS

Description Price, US$ Price, US$

Sheltered Aisle, per the Description and Bill of Material listed below $75,380.00 $75,380.00

Bus Duct, 3 phase, 2000 amp. Sized from top of switchgear to roof line. $3,350.00 $3,350.00

Freight to Vero Beach, FL for Sheltered Aisle Enclosure $14,475.00 $14,475.00

Total Line Item Net Price, US$ $93,205.00

Clarifications: All incoming I outgoing wire, and terminations by others. Specifications were not provided at time of quote. Dimensions & weights shown are approximate only and are not for construction purposes. Lead-time on approval drawings will be approximately 4-6 weeks after receipt of order. Quoted lead-time is approximate time after drawing approval, not after receipt of order. Standard SPS factory production test are included in the quoted price. Field-testing & demonstration are not included in the quoted price but is available contact the factory for rates. Switchgear Power Systems standard warranty was quoted, 18 months from ship date or 12 months after

energizing equipment (which ever comes first). Standard SPS terms and conditions apply. This design does not guarantee compliance with any regional, state or local code requirements. The governing

basis for structural design shall be the Uniform Building Code. Switchgear Power Systems reserves the right to utilize components of equal quality other than those specified. Freight is not included in the quoted price; It is shown as a separate line item. Offloading and placement by

others. Quote price expires in 30 days Personnel and equipment doors will be provided with construction cores only. Quote is based on mounting /installation onto concrete slab. If other mounting/installation methods are

necessary, an adder will be required.

Item #1 Sheltered Aisle

General Construction: Sheltered Aisle will be weatherproof NEMA3R design with self supporting I self framing interlocking panels. All exterior seams to be sealed with silicon. Base frame to be fabricated from structural steel channel, wide flange beams and angles forming a self supporting grid to support the floor or brace for shipment as required.

Nominal Dimensions: Length: 20' -0" (exterior walls) Width: 15'-3" (exterior walls) Ceiling height: 1 O'-5"

Estimated Shipping Dimensions: Length: 20'-0" Width: 15' -3" Height: 11'-6" Shipped in one piece

Page 18 of20

http:93,205.00http:14,475.00http:14,475.00http:3,350.00http:3,350.00http:75,380.00http:75,380.00

Customer: Aubrey Silvey Project: Vero Beach - Substation 9 - Switchgear Replacement ABB CCP: 1502592880 - Vero Beach-Substation 9 Date: 4/1/2015 Rev.#0;8/3/2015

Bill of Material

Page 19 of 20

Design: lasCsification: General Purpose Non-Hazardous Roof load: 30 psf International Building Code (latest revision) Wind load: International Building Code (latest revision) Floor loading: 250 psf DI + LL Base deflection 240 psf Roof panels: 12 gauge ASTM A653 Exterior wall panels: 12 gauge ASTM A653 Interior wall panels: 16 gauge ASTM A653 Ceiling panels: 14 gauge ASTM A653 Floor plate: .250" Base Frame: ASTM A572 (C10 & Larger) ASTM A36 (C8 & smaller) Base Frame Coating: Bitumastic Welding to be in accordance with the latest revision of AWS D1 .1 structural welding code. Structural member bolts: per ASTM A-325, 5/8" diameter minimum. Exterior paint finish: ANSI #70 gray Interior paint finish: White Floor finish: ANSI # 61 gray with anti-skid

Insulation: Roof insulation: R-19 Foil Faced Polyisocyanurate Foam Sheathing Wall insulation: R-19 Foil Faced Polyisocyanurate Foam Sheathing Floor insulation: R-12 Closed-cell spray applied Polyurethane Foam

Doors: 2 - Personnel Doors, Single Wide

LHRB Door 2 - 3'-0" X 8'-0" X 3-1/2" 12ga Galvanneal Single Door Frame 2 - 3'-0" X 8'-0" X 1-3/4" 12ga Galvanneal, R12 Insulated Door 8 - Hager BB1191 NRP - 4-1/2" X 4-1/2" Standard Weight Hinges, Stainless Steel 2 - Precision F 2105 X 1705A, 630 Thumb piece Mortise Panic Device 2 - Medeco Rim Cylinder, with disposable temporary core 2 - Reese 128CV x 36" Jamb weather stripping at head 4 - Reese 128CV 84" Jamb weather stripping at sides 2 - Reese 377C x 36" Sweeps 2 - Reese S484AV x 36" Threshold 2 - Reese 202C x 40" Interlocking head weather stripping 2 - Reese 203C x 36" Interlocking head weather stripping

*Personnel and equipment doors will be provided with temporary construction cores only.

8 - Danger High Voltage I Keep Out warning sign (or customer specified)

6 - Medium voltage rear access equipment doors

14 gauge steel

Pad-lockable door handles

3 point latching

Grade 5 zinc plated hardware

Door insulation: Foil lined foam board to R 12

HVAC Equipment: 1 - Heater, 240V, 5 KW, 21.4Amp draw, Chromalox or equal

1 - Thermostat

Electrical Utilities: 1 - Interior conduit- exposed EMT conduit with set screw fittings as required by NEC 1 - Power wiring: #12 AWG Type THHN I THWN 1 - Control wiring: #12 AWG Type SIS 1 - HVAC controls: #18 AWG thermostat cable 3 - Fluorescent Light Fixtures

Page 19 of20

Customer: Aubrey Silvey Project: Vero Beach - Substation 9 - Switchgear Replacement ABB CCP: 1502592880 - Vero Beach-Substation 9 Date: 4/1/2015 Rev.# 0; 8/3/2015

Bill of Material

Page20 of 20

4'x 2 lamp x 32 watt,

120Vac, with electronic ballast

Lithonia- LB232MVOLTGEB101S

3 - Light bulbs 4'-0" 32 watt, Type T-8 Lithonia - F032741ECO

2 - Exterior Light Fixtures 70 Watt, High Pressure Sodium Photocell switch Lithonia - TWS70S120PELPI

2 - Emergency I EXIT lights Two 1.8W LED lamps for emergency light Test switch Status indicator Nickel-cadmium backup battery, rechargeable Lithonia ECR LED M6

2 - 3-Way Switch I Receptacle combinations, 120 Vac, 20amp Interior lights One mounted at each entrance

2 - Switches, 1 pole, 120Vac, 20amp Exterior Lights One mounted at each entrance

Distribution Panels: 1 - AC panel board

1-phase, 3wire 120/240 V, 100 amp 12 circuit, 1 OkAIC Lot breakers as required for utility circuits NEMA1 box NEMA1 cover GE type AQ (or equal)

Grounding: 2 - Ground pads, 4-hole stainless steel welded to base frame

1 - Lot ground drops from ground loop to ground pads as required

Accessories:

1 - Set of removable lifting lugs with hardware (shipped loose)

1 - Lot floor & wall cutouts as required for cables, conduits and cable trays.

1 - Lot removable aluminum cover plates for floor cutouts.

Customer Supplied Equipment Installed By Switchgear Power Systems:

No Customer Supplied Equipment.

The Following Items Shipped Loose For Field Installation By Others: Lifting I ugs Fluorescent light bulbs Exterior lighting

Page 20 of20

111111111111111111111111111111111111111111111 111111111111111111111111111111111111111111111

INSTC0rv1PT INSTCOMPT INSTCO\i1PTINSTCOMPT INSTCOrvPT

INSTCOMPT

2000A 2000A

CPTCOl'vPT 1200A 1200A 1200A0 00 0 0 0

= l~I ~ ~ ~ l~I A01.01 A01.02 A01.03 A01.04 A01.05 A01.06

CPT Main Feeder Feeder Feeder Feeder

Width 5484 mm I 216 in, Height 2413 mm I 95 in (plus Vent 203 mm/ 8 in), Depth 2337 mm/ 92 in

Narooor,..,,;1elll00r. IRavData: I""""""' I

Aubrey Silvey Mauricio Martinez 1 Switchgear 2015-08-03 P,qoc'

Vero Beach - Substation 9 - Switc g/!18meplacement I Front view

15 kV, 2000A, 25 kA

"' ~~~E- L ! ! ! ""'~

L A01.01 A01.02 A01.03 A01.04 A01.05 A01.06

CPT Main Feeder Feeder Feeder Feeder

I "'""""" IPrei;arlby: Aubrey Silvey Mauricio Martinez \ =Beach - Substation 9 - Switc~Wt~placement

Narooof-tc~I Switchgear \ Single line diagram

DDDDDD

D [ ] [ ] [ u [ A01.01 A01.02 A01.03 A01.04 A01.05 A01.06 CPT Main Feeder Feeder Feeder Feeder

Prepared by: l'Hnaofsw.t:Cgeer:

I"''"""" Aubrey Silvey Mauticio Martinez l Switchgear IPrrjoo< Vero Beach - Substation 9 - Switc gA8ffieplacement I IU>oc l,_,oo. 1502592880 - Vero B~acMSubstTop view tion 9

Field Service Rate Schedule U.S.A.

Power Products Division Equipment Service

1 ZU L9520-001

March 1, 2013

Technical Services ABB Inc. maintains a complete staff of trained field engineers and technicians who are available to provide advisory assistance, installation, inspection, commissioning, testing, troubleshooting, start up, engineering studies, maintenance and repair services of electrical apparatus. Field engineers and technicians are classified into categories dependent upon the degree of expertise and complexity of the service required.

Class I - Service Engineer or Technical Specialist The service engineer or technical specialist has specialized educational and factory training and experience in design, assembly, installation, and testing. This person is required for special diagnosis, repairs, inspection, failure analysis, engineering evaluations, and training of customer personnel.

Class II - Lead Service Technician The lead service technician has specialized factory training and experience. This person can act as a consultant for customer's personnel with respect to correct installation, testing, maintenance, or service requirements consistent with ABB guidelines.

Class Ill - General Service Technician The service technician has craft trade training along with fadory training. The specialist will engage in performance of routine maintenance, installation and service activities.

Specialist Rates Hourly

Daily Daily Rate Hourly Sunday, Classification with Per Overtime Standby &

Rate(1) Diem Rate(2) Holiday Rate(3)

Transformer Services

Class I $2400 $2700 $450 $600

Class II $1600 $1900 $300 $400

Class Ill $1280 $1580 $240 $320

Emergency 25% surcharge added to above rates

HV, MV, & LV Circuit Breaker Services Protection & Control Equipment Services

Class I $1760 $2060 $330 $440

Class II $1440 $1740 $270 $360

Class Ill $1040 $1340 $195 $260

Emergency $2240 $2540 $420 $560

Gas Insulated Substation (GIS) Services Generator Circuit Breaker (GCB) Services

Class I GIS $2000 $2300 $375 $500

Class I GCB $1800 $2100 $338 $450

Emergency $2240 $2540 $420 $560

1. Daily rate applies to all time worked or traveled during a normal eight hour work day. The shift is defined as any consecutive eight hour period (Monday- Friday, excluding holidays) with an allowance for lunch.

2. Overtime rate applies to all hours worked or traveled in excess of eight hours on weekdays and the first eight hours worked or traveled on Saturday.

3. Sunday and Holiday rate applies to all hours work or traveled on Sundays, holidays, and in excess of eight hours on Saturday.

ABB policy is a maximum of (12) twelve working hours per day per person including travel time. Under special circumstances and with prior ABB Business Unit approval, the maximum work hours can be extended to (16) sixteen working hours per day per person including travel time.

Hourly and daily rates are exclusive of all travel and living costs.

Charges for travel and living expenses will be billed at cost plus a 25% handling charge.

Per Diem Where purchasers specify or require daily rates for field services inclusive of local traveling and living expenses, a flat charge will be billed for all time worked or traveled per eight hour weekday or fraction thereof (Monday through Friday). All hours worked or traveled in excess of eight hours per weekday and all hours on Saturdays, Sundays, and holidays will be billed at the applicable hourly overtime rates. Per diem rates exclude the cost of airfare to/from the job site and home base.

Traveling Time The billing for traveling time will be at the applicable rate for the actual time traveled. Traveling time and expenses for each specialist I technician will include leaving and returning to the employee's home base.

Minimum Billing A minimum billing for one day's service will be charged for each day or fraction thereof that a specialist I technician spends on the customer's premises.

Standby Time When specialists I technicians are on the customer's premises but are unable to perform the services requested because of circumstances beyond the control of ABB Inc., the purchaser will be charged at the applicable rate.

Preparation I Post Work Time When a specialist I technician works on a customer's project prior to the start of the field work and/or after the field work, the purchaser will be charged for all hours worked at the applicable rate.

Other Charges The following charges will be in addition to the service rates stated previously:

A. Purchased Material When the job requires the purchase of materials or services from subcontractors or other vendors or expendable tools, such items will be billed at cost plus a service charge not to exceed 30%.

B. Special Tools and Equipment Furnished by ABB A rental charge shall be made for all specialized tools, equipment, and instruments. Refer to ABB Inc. Field Service Equipment Rental Rate Schedule.

C. Company Vehicle Mileage Rate The cost of mileage for company vehicles to travel to and from the standard job site will be billed at a rate of $0.75 per mile and $200 per day.

D. Oil Processing Trailer The daily rate for an oil processing trailer will be billed at $2,500 per day, if required. Mobilization and demobilization charges will be billed at a rate of $3.50 per mile each way. The usage of an oil processing trailer requires at least four service personnel (2 of the four must be ABB personnel)

TERMS OF PAYMENT Net 30 days

TERMS AND CONDITIONS ABB Inc. "General Terms and Conditions of Sale"

1-800-HELP-365

1-800-435-7365

I DATE (MMIDD/YYYY)

CERTIFICATE OF ILITY INSURANCE 01/2912015~ THIS CERTIFICATE IS ISSUED AS A MATTER OF INFORMATION ONLY AND CONFERS NO RIGHTS UPON THE CERTIFICATE HOLDER. THIS

CERTIFICATE DOES NOT AFFIRMATIVELY OR NEGATIVELY AMEND, EXTEND OR ALTER THE COVERAGE AFFORDED BY THE POLICIES

BELOW. THIS CERTIFICATE OF INSURANCE DOES NOT CONSTITUTE A CONTRACT BETWEEN THE ISSUING INSURER(S), AUTHORIZED

REPRESENTATIVE OR PRODUCER, AND THE CERTIFICATE HOLDER.

IMPORTANT: If the certificate holder is an ADDITIONAL INSURED, the policy(ies) must be endorsed. If SUBROGATION IS WAIVED, subject to

the terms and conditions of the policy, certain policies may require an endorsement. A statement on this certificate does not confer rights to the

certificate holder in lieu of such endorsement(s). CONTACT NAME:PRODUCER

MCGRIFF, SEIBELS & WILLIAfvlS. INC. PHONE I FAXIAIC. No. Ext>: 800-476-2211P.O. Box 10265 (A!C, Nol:

Birmingham, AL 35202 E-MAIL ADDRESS:

INSURER(S) AFFORDING COVERAGE NAIC #

INSURER A :Amerisure fvlutual Insurance Company (A Stock Insurer) 1244 INSURED INSURER B :Starr Indemnity & Liability Company 38318Aubrey Silvey Enterprises. Inc. 371 Hamp Jones Road INSURER c :Hanover Insurance Company 22292 Carrollton. GA 30117

INSURER D :Amerisure Insurance Company 19488

INSURER E:

INSURER F:

COVERAGES CERTIFICATE NUMBERVT7V5BXB REVISION NUMBER

THIS IS TO CERTIFY THAT THE POLICIES OF INSURANCE LISTt::D BELOW HAVE BEEN ISSUED TO THE INSURED NAMED ABOVE FOR THE POLICY PERIOD INDICATED. NOTWITHSTANDING ANY REQUIREMENT. TERM OR CONDITION OF ANY CONTRACT OR OTHER DOCUMENT WITH RESPECT TO WHICH THIS CERTIFICATE MAY BE ISSUED OR MAY PERTAIN. THE INSURANCE AFFORDED BY THE POLICIES DESCRIBED HEREIN IS SUBJECT TO ALL THE TERMS. EXCLUSIONS AND CONDITIONS OF SUCH POLICIES. LIMITS SHOWN MAY HAVE BEEN REDUCED BY PAID CLAIMS.

INSR LTR TYPE OF INSURANCE

ADDL SUBR INSD WVD POLICY NUMBER

POLICY EFF IMMIDDIYYYYl

POLICY EXP IMMiDDIYYYY\ LIMITS

A x COMMERCIAL GENERAL LIABILITY- :J CLAli\.IS-MADE 0 OCCUR GL20810780302 0113112015 0113112016

EACH OCCURRENCE DAi\.IA\oE Tu RcN I t:D PRElvHSES (Ea occurrence)

s s

1,000,000

100,000

- MED EXP (Any one person) s 5,000 - PERSONAL & ADV INJURY s

1,000.000

GEN'L AGGREGATE LIMIT APPLIES PER: GENERAL AGGREGATE s 2,000.000 ~ POLICY 0PROJECT DLOC PRODUCTS - COMPIOP AGG s 2,000.000

OTHER: s D AUTOMOBILE LIABILITY -

CA208'10580301 0113112015 01131/2016 COMBINED SINGLE LIMIT rEa accident\ s 1.000.000

x- ANY AUTO BODILY INJURY (Per person) $ -

ALL OWNED AUTOS

~

-SCHEDULED AUTOS BODILY INJURY (Per accident)

s '

x- HIRED AUTOS x-NON-OWNED AUTOS

PROPERTY DAMAGE (Per accident) s

8 -

UMBRELLA LIAB MOCCUR 1000021517 01/31/2015 01/3112016 EACH OCCURRENCE $

s 10,000.000 x EXCESS LIAB CLAIMS-MADE AGGREGATE s 10,000,000

DED I I RETENTION s s A WORKERS COMPENSATION

AND EMPLOYERS' LIABILITY YIN ANY PROPRIETOR/PARTNER/EXECUTIVE D OFFICER!i\.IEMBER EXCLUDED? (Mandatory in NH)

NIA

WC208105903 01131/2015 01/3112016 X IJ'T~~UTE I jOTH-ER E.L. EACH ACCIDENT

E.L. DISEASE EA EMPLOYEE

s s

1,000,000

1,000,000 If yes, describe under DESCRIPTION OF OPERATIONS below E.L. DISEASE - POLICY LIMIT s 1.000,000

c Equip. Installation Fltr RHAA21049801 NO Boom or Overload Exel

01/31/2015 01/31/2016 Leased/Rented/Borrowed Ded: s1ok per Occurence

s s

250.000

except 5% of values on Cranes-Min $15k

s $

Install Fltr-Anv One Lift/Job s 4.500.000 DESCRIPTION OF OPERATIONS I LO