chest of drawers model #3077-21bl right side 3027h-drawer front 3027i- drawer bottom 3027j-back...
TRANSCRIPT
SPARTAK ENTERPRISES, INC. CHEST OF DRAWERS
Model #3077-21BL LOT #2396
IF PARTS ARE MISSING AND OR DEFECTIVE, IF INSTRUCTIONS ARE NOT CLEAROR IF YOU ARE EXPERIENCING PROBLEMS ASSEMBLING OUR PRODUCT.
BEFORE YOU RETURN THE PRODUCT TO THE STORE,PLEASE CALL US TOLL FREE FOR CUSTOMER SERVICE ASSISTANCE
(888) 777-8250OR SEND US EMAIL AT
[email protected] HAVE ITEM NUMBER READY, AND A REPRESENTATIVE WILL GLADLY ASSIST YOU
SPARTAK ENTERPRISES, INC. 841 E. FRANCIS STR. ONTARIO, CA. 91761 TEL; 909/930-0670 FAX; 909/930-9921
JI
GFE
3027G-Drawer Right Side3027H-Drawer Front3027I- Drawer Bottom3027J-Back Panel3027K-Bottom
3077A-Side Panel Left3077B-Side Panel Right3077C-Center Support3027D-Drawer Back3027E-Top3027F-Drawer Left Side
NOTE: FIRST MAKE SURE THAT YOU HAVE ALL OF THE PARTS LISTED ON THIS SHEET. IF YOU AREMISSING ANY PIECE(S), DO NOT ASSEMBLE THE UNIT. INSTEAD, CALL CUSTOMER SERVICENUMBERAT: (888) 777-8250. WE WILL BE HAPPY TO ASSIST YOU.
PARTS IDENTIFICATION
K
A B
H
C
1pc1pc2pcs6pcs1pcs6pcs
6pcs6pcs6pcs4pcs1pc
CAMLT12
CAMBT16
DOWW830
GLIDE22MM
PUSH
SRM815B
GLUEWD
NAIL1734
SFH833A
BM25
SPE610BL
SC--S
SP811BL
HARDWARE PART NUMBER DESCRIPTION QTY
HARDWARE LIST
12
12
8
4
6
12
2
40
28
24
48
4
16
CAMLOCK
BOLT
WOOD DOWEL
GLIDE
SHELL METAL PULL
MACHINE SCREW
GLUE
NAIL
WOOD SCREW
ANGLE BRACKET
EURO SCREW
SCREW COVER CAP
PAN HEAD SCREW
1
DOWW830
Insert wood dowels by tapping onto them witha hammer. Make sure they go in as far aspossible. Wood dowels should not stick outmore than 1/2"
When first inserting camlocks, make sure theyalways point towards edge of board as indicated.
UNLOCKEDPOSITION
CAMBT16 K
A&B
C
2 When locked, arrowon camlock shouldpoint away from theedge as indicated.
Turn camlockclockwise tolock the bolt
KA
B
Please follow steps above on this diagram to erect theassembly in order to avoid breakage of parts (C and K).
Finished edge
C
SFH833A
3
E
E
Raw EdgeDOWW830
Note: Make sure you align the raw edges ofpart (E) to parts (A and B) in the back whenattaching. Lightly tap on the top piece (partE) onto the unit in order not to leave anygaps in between them. Be careful becauseyou may not be able to undo this step onceglue has set.
4
G
FG
FH
SPE610BL
BM25
I
SPE610BL
Note: Once parts (F and G)have been attached to part (H)with the euro screws, a total offour each. Then slide in thebottom part of the drawer(Part I).
F
G
I
H
5D
Note: Place (D) onto (in between)Drawer Sides (F) and (G). Repeatlast steps for the rest of thedrawers.
I
Note: Attach part (D) withtwo screws on both sides(Parts F & G) a total of fourscrews as shown below.
D
IF
F
D
SFH833A
JJ
GLIDE22MM
6
JJ
NAIL1734
SRM815B
SP811BL
Place the unit face down. Align the Back Panel (J) over the of the unit. Make sure the assemblyis square and leave equal amount of margin all around. Secure the panels by screwing 4 screwsthrough the pre-drilled holes for all panels (2 screws on both ends). Next, nail the top and bottom(as shown above) with approximately 4" spacing between the nails. Make sure to keep the nailscentered on the edges to avoid splitting of the boards.