chemical anchoring hollow brick block
DESCRIPTION
Chemical Anchoring Hollow Brick BlockTRANSCRIPT
-
104 www.ramset.com.au 1300 780 063
Hollow Brick & Block Medium Duty Anchoring
Hollow Brick and Block Anchoring AccessoriesUse with ChemSet 101 and Ultrafix Plus to anchor threaded studs into hollow brick and block Forms a solid plug of adhesive in the brick or block cavity to provide
secure anchoring pointDurable nylon sleeves ideal for 3 hole brick and hollow concrete block Fine Metal Mesh Sleeves ideal for 10 hole brick
Typical Properties Nylon Sleeve Wire Mesh Sleeve
For ThreadSize
Overall Length (mm)
Nominal Diameter
(mm)
Overall Length (mm)
Nominal Diameter
(mm)M6 - - 1000 12.5M8 64 12 1000 12.5M10 64 14 1000 15.0M12 64 16 1000 15.0M16 - - 1000 20.5
Substrates Wire Cut Extruded Clay Brick, Hollow Concrete Block
Features and BenefitsResistant to vibrating loadsCorrosion resistant nylonNo expansion stress on bricksNon-destructive installation Easy, simple and quick to install
Chem
Set
Anch
or Fi
xings
Patented design ensures adhesive is extruded where it is needed most
Non-perforated tip - no wasted adhesive
Related ProductsDynaDrill Carbide Drill BitsDiamond MotorDiamond Core Drill Bits
Hole Cleaning BrushesHole Cleaning Pump UltraFix PlusChemSet 101
-
www.ramset.com.au 1300 780 063 105
Anchor
Installation details Working Load Limit (kN)
size, db
Substrate Drilled hole diameter, dh Fixture hole Anchor Tightening 3 Hole Brick 10 Hole Brick Concrete Block
(mm)
(mm) diameter, effective depth, torque, Tr Nylon Sleeve S/S Sieve df (mm) h (mm) (Nm)
Shear, Va Tension, Na Shear, Va Tension, Na Shear, Va Tension, Na
M8 3 Hole Brick, 12 12 10 10 3.8 2.5 3.0 1.0 1.8 1.8
M10 10 Hole Brick 14 16 12 64 20 4.6 2.5 4.6 1.0 2.0 1.8
M12 or Concrete 16 16 15 40 5.0 2.5 5.0 1.0 2.0 1.8
M16 Block
22 19 95 5.0 2.5 5.0 1.0 2.0 1.8
Hollow Brick & Block Medium Duty Anchoring
Installation1. Drill hole to specified diameter in brick or block using a masonry drill bit2. Brush and blow dust out of holes 3. Cut wire mesh sleeves to length nominated in table below and fold or twist one end to close it4. Insert nylon or wire mesh sleeve into hole5. Insert ChemSet 101 or Ultrafix Plus mixing nozzle into sleeve and dispense adhesive, withdrawing nozzle as it fills6. Insert threaded rod or stud into sleeve 7. Allow adhesive to cure before loadingRefer to Technical Data Sheet and MSDS available from www.ramset.com.au, for precautions and further detailed installation instructions
Hollow Brick and Block Anchoring AccessoriesDescription To Suit Part Number Pack QuantityNylon Sleeve 12 mm Diameter M8 Thread ISS08 100Nylon Sleeve 14 mm Diameter M10 Thread ISS10 100Nylon Sleeve 16 mm Diameter M12 Thread ISS12 100Fine Metal Mesh Sleeve12 x 1000 mm M8 Thread ISM08 1Fine Metal Mesh Sleeve16 x 1000 mm M10 / M12 Thread ISM12 1Fine Metal Mesh Sleeve 22 x 1000 mm M16 Thread ISM16 1
Trades & ApplicationsBuilding Contractor Steel Fabricator Balustrade Contractor Fitter
Hand rails 4 4
Gate Hinges 4
Timber Beams 4
Steel Beams 4 4
ChemSet
Anchor Fixings
Indicative Working Loads in Hollow Brick/Block with ChemSet 101, Ultrafix Plus & ChemSet Hollow Block Accessories
The strength in tension of ChemSet fixings for hollow block exceeds the strength of hollow brick and concrete block. Therefore load capacity of the fixing is limited by the strength of the brick or block. Over loading the fixing will risk destruction of the brick or block. Shear properties based on grade 4.6 carbon steel threaded rod.
The design engineer should ensure the structural element is capable of supporting these loads.Refer to Ramset Specifiers Resource Book for more information or explanation of technical data.