chapter 3 consol ppt by e.cussler
DESCRIPTION
diffusion in mass transfer and liquids reference E cusllerTRANSCRIPT
10. October 2012
Chapter 3
Diffusion in Concentrated Solutions Dr. K. Wegner - Lecture 10.10.2012
Mass Transfer
Mass Transfer – Diffusion in Concentrated Solutions 2
3. DIFFUSION IN CONCENTRATED SOLUTIONS
Diffusion causes convection in fluids
Convective flow occurs because of pressure gradients (most common) or temperature differences (buoyancy or free or natural convection). However even in isothermal and isobaric systems, convection can occur due to diffusion.
Maxwell (1860) said: “Mass transfer is due partly to the motion of translation and partly that of agitation.”
Diffusion and convection always occur together in fluids.
3.1 Theory
Mass Transfer – Diffusion in Concentrated Solutions
Example: Evaporation of Benzene:
3
At 6°C the benzene vapor is dilute and evaporation is limited by diffusion.
At 80.1°C benzene boils (p = 1atm).Evaporation is controlled by convection.
At 60°C an intermediate case occurs in which both diffusion and convection are important.
Mass Transfer – Diffusion in Concentrated Solutions
Analysis of the case at 60°C:
4
Concentration of benzene (species 1) and air (species 2) at z = h:
c1,h = c1,∞ (→ 0); c2,h → max
p1,h = p1,∞ (→ 0); p2,h → p
(air blows away and dilutes benzene vapor).
At z = 0:
c1,0 = f (T,p) > c1,h and c2,0 < c2,h
p1,0 = f (T,p) > p1,h and p2,0 < p2,h
Mass Transfer – Diffusion in Concentrated Solutions 5
The difference in concentrations (or partial pressures) between 0 and h gives rise to upward diffusion of benzene from the liquid surface and downward diffusion of air.
Since the benzene surface is considered impermeable to air, a convective upward-pointing flux must compensate the downward diffusive flux of air!
This is the Stefan flow !
NOTE: This convection also transports benzene molecules!
Mass Transfer – Diffusion in Concentrated Solutions
Determine concentration profile and flux for the 60°C case
6
Mass balance for species i at steady state:
)zz(J)zz(J)z(J)z(J diff,iconv,idiff,iconv,i
Diffusive flux:
dzdcADJ diffi ,
Convective flux with velocity u:
uAcJ iconvi ,
Mass Transfer – Diffusion in Concentrated Solutions 3-7
For Δz → 0 we obtain:
02
2
zcD
zcu ii
For practicability we transform molar concentrations into mole fractions:
cc
VccVc
nnny 1
21
1
21
11
(1)
If c is given as a mass concentration the transformation into mole fractions is:
1
11 M
Mcy
with the “average molar mass” i
ki MyM 1
Mass Transfer – Diffusion in Concentrated Solutions 3-8
So (1) can be rewritten as: 02
2
zyD
zyuc ii (2)
Integration of eq. (2) for species 1 (benzene):
CzyDyuc
11 (3)
The two terms are the convective and diffusive molar flux densities. The sum of the molar fluxes is constant.
Integration of eq. (2) for species 2 (air) with 12 1 yy
CzyDy1uc 1
1
(4)
Mass Transfer – Diffusion in Concentrated Solutions 3-9
Since air does not accumulate and cannot penetrate the benzene surface, the total (overall) molar flux of air is zero. Thus 0C
Eq. (4) is rewritten as:
zy
uDy 1
11 (5)
Integration of (5) with B.C. y1 = y1,0 at z = 0:
zDu
eyy 0,11 11 (6)
Determine velocity u with B.C. y1 = y1,h at z = h:
0,1
,1
11
lnyy
hDu h
(7)
Mass Transfer – Diffusion in Concentrated Solutions 3-10
Inserting eq. (7) into (5) gives the concentration profile:
hz
h
yy
yy
0,1
,1
0,1
1
11
11 (8)
With the concentration profile and eq. (3) we can obtain the total molar flux:
0,1
,1
11
lnyy
hDcCj h
tot (9)
This type of approach leads to the Stefan-Maxwell equations for multi-component diffusion in concentrated solutions.
Mass Transfer – Diffusion in Concentrated Solutions
Separating Convection from Diffusion – Cussler’s Approach
3-11
Now, Cussler treats this topic slightly different (but gets to the same results).
Assume that these two effects are additive:
convection by
dtransporte massdiffusion by
dtransporte massdtransporte mass total
If the total mass flux is n1, the mass transported per area per time relative to fixed coordinates:
111 vcn
where v1 is the average solute velocity (velocity due to convection and superimposed diffusion).
Mass Transfer – Diffusion in Concentrated Solutions 3-12
The total average solute velocity can be split into a part due to diffusion and one due to convection, called reference velocity va:
convection
a1
fluxdiffusive
a1
a1
a111 vcjvcvvcn
The art is to select va in such a way that va=0.
For example va is the velocity of the solvent because the solvent is usually in excess so its transfer is minimal (in other words the difference in solvent concentration is too small across the solution). That way we eliminate convection and deal with a SIMPLER problem.
Mass Transfer – Diffusion in Concentrated Solutions 3-13
Two-bulb apparatus (Diaphragm-cell) for understanding different definitions of reference velocities.
Volume average velocity = 0Molar average velocity = 0Mass average velocity ≠ 0
Volume average velocity = 0Molar average velocity ≠ 0Mass average velocity ≈ 0
Mass Transfer – Diffusion in Concentrated Solutions 3-14
For gases (e.g. H2 and N2) at equal T and p the number of moles is always the same in both sides. Similarly the volume in both sides is the same. As a result, the
v0 = 0 volume average velocity
v* = 0 molar average velocity
v 0 mass average velocity, because the masses of N2 and H2 are different. As a result, as time goes by the center of mass in the two-bulb apparatus moves away from the bulb containing N2 initially. Thus the mass average velocity v is not zero.
Mass Transfer – Diffusion in Concentrated Solutions 3-15
For liquids: The volume is nearly always constant.v0 = 0 volume average velocityv = 0 mass average velocity. This is usually correct as liquid
densities differ little.e.g. H2O=1 g/cm3
Glycerol=1.1 g/cm3
However, the molar concentration is usually quite different following large differences in molecular weight.
e.g. MWH2O=18 g/mol andMWGlycerol=92 g/mol
So v*0 molar average velocity for liquids.
In conclusion: For gases use as reference velocity va the v0 or v*, while for liquids use v0 or v.
Mass Transfer – Diffusion in Concentrated Solutions 3-16
Mass Transfer – Diffusion in Concentrated Solutions 3-17
Table legend:
ω i : mass fraction of species iy i : mole fraction of species i
ii Vc : volume fraction of species i, iVwhere is the partial specific volume of species.
Precisely: Partial specific volume:jmTpi
i mVV
,,
Partial molar volume:jnTpi
i nVV
,,
The partial specific or molar volume expresses how much a volume changes upon addition of a certain mass or number of moles of a given component.
Mass Transfer – Diffusion in Concentrated Solutions 3-18
Partial molar volume for ideal gases (pV = nRT) :
cpTR
np
RTnn
nVV
nTp
nTp
1
2
2
,,
1
21
,,11
Mass Transfer – Diffusion in Concentrated Solutions
3.2 Examples for Parallel Diffusion and Convection
3-19
Example 3.2.1: Fast Diffusion through a stagnant film
Goal: Calculate the flux and the concentration profile
Now both diffusion and convection are important!
Remember that at intermediate temperatures both diffusion and convection affect the evaporation of benzene (or any other solute).
Mass Transfer – Diffusion in Concentrated Solutions 3-20
1. Step: Mass balance
zzatout
dtransportesolutezatin
dtransportesolutezAvolumein
daccumulatesolute
zz1z11 |An|AnczAt
Divide by Az and as volume 0
znc
t1
1
At steady state:
zn0 1
Mass Transfer – Diffusion in Concentrated Solutions 3-21
Now the flux is affected by both diffusion and convection. For simplicity we choose va=v0 (volume average velocity)
)vVcvVc(cdzdc
Dvcjn 222111110
111
2. Step: Choose and simplify mass transport equation
Note that n1=c1v1 and n2=c2v2
The total average flux of the solvent (air) is zero, since it cannot penetrate into the liquid phase and does not accumulate.
Therefore n2=0 and v2=0.
(Cussler mentions that the solvent vapor is stagnant and therefore n2=0 and v2=0. This does not make sense physically, though.)
Mass Transfer – Diffusion in Concentrated Solutions 3-22
So 1111
1 nVcdzdc
Dn
If the vapor is an ideal gas, then 111
21
11 Vc
cc
VccVcy
dzdcD)Vc1(n 1111
dzdyDc)y1(n 1
11 (1)
3. Step: Boundary conditions z=0: y1=y10
z=L: y1=y1L
(2)
(3)
or
and
Mass Transfer – Diffusion in Concentrated Solutions 3-23
Solve eqn. (1) subject to BC’s to determine n1
10
11 y1
y1lnDcn
(4)
Note that doubling the concentration difference DOES NOT double the flux, as in dilute systems.
Integrating eq. (1) also for z=0 to z and y1=y10 to y1 and assuming that n1 does not change with height z (which is a fair assumption here as the cross-sectional area does not change) gives:
z
10
1
10
1y1y1
y1y1
(5)Concentration profile
Mass Transfer – Diffusion in Concentrated Solutions 3-24
10
1
z
10
110
y1y1ln
y1y1y1Dc
dz1dy
Dc1j
(6)
0,1
,1
11
lnyy
hDcCj h
tot
Compare to our initial result for combined diffusion and convection of benzene (page 3-10):
Eq. 6 gives the same results assuming y1L=y1h→0 and z=L=h
The direct approach and the one using the reference velocity give the same results!
Mass Transfer – Diffusion in Concentrated Solutions 3-25
Now does this result reduce to that for dilute solutions?
Expansion into series for small y (dilute system small conc. y):
32a y
!32a1aay
!21aaya1y1
(7)
(8)
(9)
ya1y!3
2a1aay!2
1aaya1y1 32a
Here a=1: y1y1
1
y3y
2yyy1ln
32
0 0
Mass Transfer – Diffusion in Concentrated Solutions 3-26
Let´s apply eqn. (8) to eqn. (5)
z101
z101
10
1 yy1y1y1y1y1
z
101101 yy1)y1(y1
1101010110 yyzy1yzyz1y1
If we multiply both sides of eqn. (10) with c
(10)
)cc(zcc 101101
(11)
with approx. (7) becomes
Mass Transfer – Diffusion in Concentrated Solutions 3-27
Likewise for the flux from eqn. (4)
)cc(DyyDc
)y1ln()y1ln(Dcn
1101019Eq
1011
Eqn. (11) and (12) are identical to the dilute limit ones!
(12)
Mass Transfer – Diffusion in Concentrated Solutions
Example 3.2.2: Calculate the error associated with the neglect of diffusion-driven convection when estimating the evaporation rate of benzene @ 6°C and @ 60°C.
a) At 6°C the saturation vapor pressure is p1(sat) = 37 mmHg
Mole fraction 049.076037
p)sat(p
ccy 11
10
Total flux at steady-state for concentrated solution:
cD05.0
049.0101lncD
y1y1lncDn10
11
Total flux for dilute solution:
cD049.00049.0cDyycDjn 11011 Only 2% error!
Mass Transfer – Diffusion in Concentrated Solutions 3-29
b) At 60°C the saturation vapor pressure is p1(sat) = 395 mmHg
760395y10 Mole fraction
Concentrated solution:
cD73.0
760/395101lncD
y1y1lncDn10
11
Dilute solution:
cD52.00
760395cDyycDjn 11011
There is 40% error !!
Mass Transfer – Diffusion in Concentrated Solutions 3-30
Example 3.2.3: Catalytic cracking of methane
Methane gas is cracked at the surface of a solid catalyst forming hydrogen and a solid carbon deposit.
Goal: Total methane (molar) flux per unit area at steady state?
n1 Catalyst surface
n2
z0
CH4
2H2Carbon deposit
CH4(g) → C(s) + 2 H2(g)
Mass Transfer – Diffusion in Concentrated Solutions 3-31
Choose and simplify mass transport equation:
Note: For processes with chemical reactions, it is best to use the molar flux and the molar average velocity!
Thus, from Table 3.2.1: *1
1*111 vc
dzdcDVcjn (1)
withc
nnvyvyv 212211
* (2)
Now 1 mole of CH4 gives 2 moles of H2, flowing in the opposite direction. Therefore,
12 2 nn in eq. (2):cnv 1* and
cnc
dzdcDn 1
11
1
Mass Transfer – Diffusion in Concentrated Solutions 3-32
Use molar fractions ccy 1
1
111
1 nydzdycDn
dzdycDyn 1
11 1 → (3)
B.C.: z = 0: y1 = 0 (due to decomposition)z = L: y1 = y1,L (some measured conc. at L)
Integration of (3) subject to B.C.s yields: LyL
Dcn 11 1ln
Or the general form if y1,0 ≠ 0:
0,1
,11 1
1ln
yy
LDcn L
Mass Transfer – Diffusion in Concentrated Solutions 3-33
Example 3.2.4: Fast Diffusion into Semi-Infinite Slab
A volatile liquid solute evaporates into a long capillary
Initially the capillary contains no solute. As the solute evaporates the interface between the vapor and the liquid solute drops.
Goal: Calculate the solute evaporation rate accounting for diffusion induced convection and the effect of moving interface.
Mass Transfer – Diffusion in Concentrated Solutions 3-34
Mass balance:
outtransport
soluteintransport
solutezAin
ionaccummulatsolute
zz1z11 nAnAzAct
Divide by A z and as z 0
zn
tc 11
(1)
There is no solvent (air) flow across the capillary, blowing the solute away. As a result, the solute accumulates in the capillary.
Mass Transfer – Diffusion in Concentrated Solutions 3-35
Choose and simplify mass transport equation:n1 = j1+c1 v0 2211222111
0 VnVnvVcvVcv with
The solvent gas does not dissolve in the liquid, thus at the interface (z=0): n2 = 0.
012
12
1 vczz
cD
tc
In (1):
0z1
0z111 zc
DnVc1
(2)
(3)
zc
Vc1z
cVD
z
cD
tc 1
0z
11
11
21
21
(4)
Mass Transfer – Diffusion in Concentrated Solutions 3-36
t = 0 z > 0 c1 = 0t > 0 z = 0 c1 = c1(sat)
z = c1 = 0
Boundary conditions:
Define combined variabletD
z
4
0d
dc2
d
cd 121
2
(5)
with B.C. = 0 c1 = c1(sat) = c1 = 0
Mass Transfer – Diffusion in Concentrated Solutions 3-37
where
0
11
11
Vc1
cV
21
(6)
In eq. (5) is a dimensionless velocity characterizing the convection by diffusion and the movement of the interface. Note that if = 0 the problem reduces to that of diffusion in dilute concentrations !!
Eqn. (5) is integrated to give:
21 )(expttanconsc
Mass Transfer – Diffusion in Concentrated Solutions
2nd integration and insertion of B.C.:
erf
erfsatc
c1
1)(1
1(7)
eqn. (6) (7):
1
211experf1
11)sat(cV
Calculate now the interfacial flux
0z
11
14.eqn
0z11 Vc1z
c
DnN
erf1exp
)sat(cV11)sat(ct/D
2
11itlimdilute
1
Mass Transfer – Diffusion in Concentrated Solutions 3-39