centerline 2100 motor control centers mains and incoming

Technical DataOriginal Instructions

CENTERLINE 2100 Motor Control Centers Mains and Incoming Lines Dimension ReferenceBulletin Numbers 2191M, 2192M, 2193M

Topic PageSummary of Changes 2Application Notes 3Catalog Numbers 3Main Incoming Lines 4Main Fusible Disconnects 12Main Circuit Breakers 28Conduit Entry - Top 38Conduit Entry - Bottom 43Additional Resources 49

CENTERLINE 2100 Motor Control Centers Mains and Incoming Lines Dimension Reference Technical Data

Summary of Changes

This publication contains the following new or updated information. This list includes substantive updates only and is not intended to reflect all changes.

Topic PageAdded dimensions for conduit entry for 100 ms ArcShield motor control centers. 38 and 39

2 Rockwell Automation Publication 2100-TD018C-EN-P - April 2020

Bulletin 2100 CENTERLINE 2100 Motor Control Centers Mains and Incoming Lines Dimension Reference Technical Data

Application Notes

This guide contains cabling dimensions for main incoming line compartments, fusible disconnect switch mains, and circuit breaker mains in Bulletin 2100 CENTERLINE® motor control centers. Lug pad dimensions are included for main incoming line compartments. The fusible disconnect and circuit breaker mains drawing include dimensions for standard lugs, and optional lugs (if specified).

Catalog Numbers

Every CENTERLINE motor control center unit is defined by a catalog number. For mains, these catalog numbers are of the following form:

The catalog numbers appear on the unit label, located on the unit bottom plate. For assembled motor control centers, catalog numbers for each unit are also listed on the Job-specific Drawings (Form 385) that ship with the order.

IMPORTANT Although this guide is accurate at the time of printing, there are differences between these drawings and the actual product, due to recent design enhancements. Always refer to the Job-specific Drawings (Form 385) for the most accurate drawings and dimensions.

IMPORTANT Dimensions are shown in inches and (millimeters). Reference dimensions include a tolerance of ±1/8 inches (±3.2 millimeters).

Catalog Number Example

Type of Main Catalog Bulletin Number Catalog Number ExampleIncoming Line 2191M 2191MT-CAC-54Fusible Disconnect 2192M 2192MB-GAC-29RCircuit Breaker 2193M 2193MT-FJC-54WT-83C500

Rockwell Automation Publication 2100-TD018C-EN-P - April 2020 3


Main Incoming Lines(a)

(a) Optional ground bus location. The front face of the 1/4 in. ground bus is located 7.41 in. (188 mm) from the cabinet front. Incoming cable pull is not correctly represented in the diagram.

Figure 1 - 300 A Incoming Line Compartment, Top Entry, 1.0 Space Factor(a)

Figure 2 - 300 A Incoming Line Compartment, Bottom Entry, 1.0 Space Factor(a)

Figure 3 - 600 A Incoming Line Compartment, Top Entry, 1.0 Space Factor(a)

Figure 4 - 600 A Incoming Line Compartment, Bottom Entry, 1.0 Space Factor(a)



(a)


Figure 5 - 800 A Incoming Compartment Top Entry, 1.5 Space Factor(a)

Figure 6 - 800 A Incoming Compartment Bottom Entry, 1.5 Space Factor(a)

Figure 7 - 800 A Incoming Compartment Top Entry in Horizontal Wireway (additional 12 in. Pull Box required to meet NEC wire bending requirements)(a)

Figure 8 - 800…1200 A Incoming Compartment Top Entry 1.0 Space Factor (additional 12 in. Pull Box required to meet NEC wire bending requirements)(a)



(a)


Figure 9 - 800 A Incoming Line Compartment Top Entry, 1.5 Space Factor(a)

Figure 10 - 800 A Incoming Line Compartment Bottom Entry, 1.5 Space Factor(a)

Figure 11 - 800…1200 A Incoming Line Compartment Top Entry, 2.0 Space Factor(a)

Figure 12 - 800…1200 A Incoming Line Compartment Bottom Entry, 2.0 Space Factor(a)



(a)


Figure 12 - 600…1600 A Incoming Line Section Top Entry, 6.0 Space Factor(a)

Figure 13 - 600…1600 A Incoming Line Section Bottom Entry, 6.0 Space Factor(a)

Figure 14 - 2000 A Incoming Line Section Top Entry, 6.0 Space Factor(a)

Figure 15 - 2000 A Incoming Line Section Bottom Entry, 6.0 Space Factor(a)



(a)


Figure 17- 600…1200 A Corner Incoming Line Section Top Entry, 6.0 Space Factor(a)

Figure 18 - 600…1200 A Corner Incoming Line Section Bottom Entry, 6.0 Space Factor(a)

Figure 19 - 1600 A Corner Incoming Line Section Top Entry, 6 Space Factor(a)

Figure 20 - 1600 A Corner Incoming Line Section Bottom Entry, 6 Space Factor(a)



(a)


Figure 21 - 600…1200 A, 10 in. Wide Incoming Line Section Top Entry, 6.0 Space Factor (left-hand version shown)(a)

Figure 22 - 600…1200 A, 10 in. Wide Incoming Line Section Bottom Entry, 6.0 Space Factor (left-hand version shown)(a)



(a)


3.00(76.2)

2.562(65.1)

3.310(84.07) 0.75 ± 0.010

(19.10 ± 0.25)

1.875 ± 0.010(47.63 ± 0.25)

5.687 ± 0 .031(144.45 ±0.79)

Figure 23 - #6-350 kcmil, One Cable Mechanical Lug Figure 24 - #6-350 kcmil, Two Cable Mechanical Lug

Figure 25 - 350…800 kcmil, One Cable Mechanical Lug

Figure 26 - #4/0-600 kcmil, One Cable Mechanical Lug Figure 27 - #4/0-600 kcmil, Two Cable Mechanical Lug

Figure 28 - #4/0-600 kcmil, Two Cable Mechanical Lug



(a)


Figure 29 - 250 kcmil Panduit Crimp Lug Figure 30 - 250 kcmil Burndy Crimp Lug






Main Fusible Disconnects(a)


Figure 37 - 30 A Main Fusible Disconnect Top Entry, 1.5 Space Factor with #14…#8 AWG Mechanical Lugs, 1 per Phase(a)

Figure 38 - 30 A Main Fusible Disconnect Bottom Entry, 1.5 Space Factor with #14…#8 AWG Mechanical Lugs, 1 per Phase(a)

Figure 39 - 60 A Main Fusible Disconnect Top Entry, 1.5 Space Factor with #14…#8 AWG Mechanical Lugs, 1 per Phase(a)

Figure 40 - 60 A Main Fusible Disconnect Bottom Entry, 1.5 Space Factor with #14…#8 AWG Mechanical Lugs, 1 per Phase(a)



(a)


Figure 41 - 100 A Main Fusible Disconnect Top Entry, 1.5 Space Factor with #8…1/0 AWG Mechanical Lugs, 1 per Phase(a)

Figure 42 - 100 A Main Fusible Disconnect Bottom Entry, 1.5 Space Factor with #8…1/0 AWG Mechanical Lugs, 1 per Phase(a)

Figure 43 - 200 A Main Fusible Disconnect Top Entry, 2.0 Space Factor with #6…4/0 AWG or #6…250 kcmil Mechanical Lugs, 1 per Phase(a)

Figure 44 - 200 A Main Fusible Disconnect Bottom Entry, 2.0 Space Factor with #6…4/0 AWG or #6…250 kcmil Mechanical Lugs, 1 per Phase(a)



(a)


Figure 45 - 400 A Main Fusible Disconnect Top Entry, 2.5 Space Factor with Two Cable 1/0…250 kcmil Mechanical Lugs, 1 per Phase(a)

Figure 46 - 400 A Main Fusible Disconnect Bottom Entry, 2.5 Space Factor with Two Cable 1/0…250 kcmil Mechanical Lugs, 1 per Phase(a)

Figure 47 - 400 A Main Fusible Disconnect Top Entry, 2.5 Space Factor with 250 kcmil Panduit Crimp Lugs, 2 per Phase(a)

Figure 48 - 400 A Main Fusible Disconnect Top Entry, 2.5 Space Factor with 500 kcmil Panduit Crimp Lugs, 1 per Phase (additional 12 in. Pull Box required to meet NEC wire bending requirements)(a)



(a)


Figure 49 - 400 A Main Fusible Disconnect Top Entry, 2.5 Space Factor with 250 kcmil Burndy Crimp Lugs, 2 per Phase(a)

Figure 50 - 400 A Main Fusible Disconnect Top Entry, 2.5 Space Factor with 500 kcmil Burndy Crimp Lugs, 1 per Phase (additional 12 in. Pull Box required to meet NEC wire bending requirements)(a)

Figure 51 - 600 A Main Fusible Disconnect Top Entry, 3.5 Space Factor with #2…600 kcmil Mechanical Lugs, 2 per Phase(a)

Figure 52 - 600 A Main Fusible Disconnect Bottom Entry, 3.5 Space Factor with #2…600 kcmil Mechanical Lugs, 2 per Phase(a)



(a)


Figure 53 - 600 A Main Fusible Disconnect, Top Entry, 3.5 Space Factor with 500 kcmil Panduit Crimp Lugs, 2 per Phase(a)

Figure 54 - 600 A Main Fusible Disconnect, Bottom Entry, 3.5 Space Factor with 500 kcmil Panduit Crimp Lugs, 2 per Phase(a)

Figure 55 - 600 A Main Fusible Disconnect, Top Entry, 3.5 Space Factor with 500 kcmil Burndy Crimp Lugs, 2 per Phase(a)

Figure 56 - 600 A Main Fusible Disconnect, Bottom Entry, 3.5 Space Factor with 500 kcmil Burndy Crimp Lugs, 2 per Phase(a)



(a)


Figure 57 - 600 A Main Non-fusible Disconnect, Top Entry, 3.5 Space Factor with #2…600 kcmil Mechincal Lugs, 2 per Phase(a)

Figure 58 - 600 A Main Non-fusible Disconnect, Bottom Entry, 3.5 Space Factor with #2…600 kcmil Mechincal Lugs, 2 per Phase(a)

Figure 59 - 600 A Main Non-fusible Disconnect, Top Entry, 3.5 Space Factor with 500 kcmil Panduit Crimp Lugs, 2 per Phase(a)

Figure 60 - 600 A Main Non-fusible Disconnect, Bottom Entry, 3.5 Space Factor with 500 kcmil Panduit Crimp Lugs, 2 per Phase(a)



(a)


Figure 61 - 600 A Main Non-fusible Disconnect, Top Entry, 3.5 Space Factor with 500 kcmil Burndy Crimp Lugs, 2 per Phase(a)

Figure 62 - 600 A Main Non-fusible Disconnect, Bottom Entry, 3.5 Space Factor with 500 kcmil Burndy Crimp Lugs, 2 per Phase(a)

Figure 63 - 800 A Main Fusible Disconnect, Top Entry, 3.5 Space Factor with #6…350 kcmil Mechanical Lugs, 3 per Phase(a)

Figure 64 - 800 A Main Fusible Disconnect, Bottom Entry, 3.5 Space Factor with #6…350 kcmil Mechanical Lugs, 3 per Phase(a)



(a)








(a)


Figure 69 - 800 A Main Non-fusible Disconnect, Top Entry, 3.5 Space Factor with #6…350 kcmil Mechanical Lugs, 3 per Phase(a)

Figure 70 - 800 A Main Non-fusible Disconnect, Bottom Entry, 3.5 Space Factor with #6…350 kcmil Mechanical Lugs, 3 per Phase(a)





(a)




Figure 75 - 1200 A Main Fusible Disconnect, Top Entry, 3.5 Space Factor with #6…350 kcmil Mechanical Lugs, 4 per Phase(a)

Figure 76 - 1200 A Main Fusible Disconnect, Bottom Entry, 3.5 Space Factor with #6…350 kcmil Mechanical Lugs, 4 per Phase(a)



(a)








(a)


Figure 81 - 1200 A Main Non-fusible Disconnect, Top Entry, 3.5 Space Factor with #6…350 kcmil Mechanical Lugs, 4 per Phase(a)

Figure 82 - 1200 A Main Non-fusible Disconnect, Bottom Entry, 3.5 Space Factor with #6…350 kcmil Mechanical Lugs, 4 per Phase(a)





(a)




Figure 87 - 1600 A Main Fusible or Non-fusible Disconnect, Top Entry, 6.0 Space Factor with #2…600 kcmil Mechanical Lugs, 4 per Phase(a)

Figure 88 - 1600 A Main Fusible or Non-fusible Disconnect, Bottom Entry, 6.0 Space Factor with #2…600 kcmil Mechanical Lugs, 4 per Phase(a)



(a)


Figure 89 - 1600 A Main Fusible or Non-fusible Disconnect, Top Entry, 6.0 Space Factor with 500 kcmil Panduit Crimp Lugs, 5 per Phase(a)

Figure 90 - 1600 A Main Fusible or Non-fusible Disconnect, Bottom Entry, 6.0 Space Factor with 500 kcmil Panduit Crimp Lugs, 5 per Phase(a)

Figure 91 - 1600 A Main Fusible or Non-fusible Disconnect, Top Entry, 6.0 Space Factor with 500 kcmil Burndy Crimp Lugs, 5 per Phase(a)

Figure 92 - 1600 A Main Fusible or Non-fusible Disconnect, Bottom Entry, 6.0 Space Factor with 500 kcmil Burndy Crimp Lugs, 5 per Phase(a)



(a)


Figure 93 - 2000 A Main Fusible or Non-fusible Disconnect, Top Entry, 6.0 Space Factor with #2…600 kcmil Mechanical Lugs, 6 per Phase(a)

Figure 94 - 2000 A Main Fusible or Non-fusible Disconnect, Bottom Entry, 6.0 Space Factor with #2…600 kcmil Mechanical Lugs, 6 per Phase(a)

Figure 95 - 2000 A Main Fusible or Non-fusible Disconnect, Top Entry, 6.0 Space Factor with 500 kcmil Panduit Crimp Lugs, 6 per Phase(a)

Figure 96 - 2000 A Main Fusible or Non-fusible Disconnect, Bottom Entry, 6.0 Space Factor with 500 kcmil Panduit Crimp Lugs, 6 per Phase(a)



(a)


Figure 97 - 2000 A Main Fusible or Non-fusible Disconnect, Top Entry, 6.0 Space Factor with 500 kcmil Burndy Crimp Lugs, 6 per Phase(a)

Figure 98 - 2000 A Main Fusible or Non-fusible Disconnect, Bottom Entry, 6.0 Space Factor with 500 kcmil Burndy Crimp Lugs, 6 per Phase(a)



Main Circuit Breakers(a)


11.13(283) 7.28

(185)

7.28(185)

5.16(131)

7.24(184)

7.24(184)

5.05(128)

10.57(268.5)

Figure 99 - 150 A Main Circuit Breaker, Top Entry, 1.5 Space Factor, with #14…#1/0 AWG Mechanical Lugs, 1 per Phase, 15…125 A Trips(a)

Figure 100 - 150 A Main Circuit Breaker, Bottom Entry, 1.5 Space Factor, with #14…#1/0 AWG Mechanical Lugs, 1 per Phase, 15…125 A Trips(a)

Figure 101 - 250 A Main Circuit Breaker, Top Entry, 1.5 Space Factor, with #10…250 kcmil Mechanical Lugs, 1 per Phase, 70…250 A Trips(a)

Figure 102 - 250 A Main Circuit Breaker, Bottom Entry, 1.5 Space Factor, with #4…250 kcmil Mechanical Lugs, 1 per Phase, 70…250 A Trips(a)



(a)


16.88(428.75) 6.90

(175.25)

6.90(175.25)

11.38(289)

6.15(156.2)

6.15(156.2)

6.96(177)

6.96(177)

15.94(405)

11.38(289)

Figure 103 - 400 A Main Circuit Breaker, Top Entry, 2.0 Space Factor, with 250…500 kcmil Mechanical Lugs, 1 per Phase, 300 A(a)

Figure 104 - 400 A Main Circuit Breaker, Bottom Entry, 2.0 Space Factor, with 250…500 kcmil Mechanical Lugs, 1 per Phase, 300 A Trip(a)

Figure 105 - 400 A Main Circuit Breaker, Top Entry, 2.0 Space Factor, with 2/0…250 kcmil Mechanical Lugs, 2 per Phase, 400 A Trip(a)

Figure 106 - 400 A Main Circuit Breaker, Bottom Entry, 2.0 Space Factor,with 2/0…250 kcmil Mechanical Lugs, 2 per Phase, 400 A Trip(a)



(a)


11.16(283.5)

7.64(194)

6.12(155.4)

11.68(296.7)

7.64(194)

6.12(155.4)

11.61(283.5)

6.46(164.1)

10.94(278)

6.4(162.6)

Figure 107 - 400 A Main Circuit Breaker, Top Entry, 2.0 Space Factor, with 250 kcmil Panduit Crimp Lugs, 2 per Phase, 300…400 A Trips (optional Pull Box provides an additional 12 in. of bending space)(a)

Figure 108 - 400 A Main Circuit Breaker, Top Entry, 2.0 Space Factor, with 250 kcmil Burndy Crimp Lugs, 2 per Phase, 300…400 A Trips (optional Pull Box provides an additional 12 in. of bending space)(a)

Figure 109 - 400 A Main Circuit Breaker, Top Entry, 2.0 Space Factor, with 500 kcmil Panduit Crimp Lugs, 1 per Phase, 300 A Trips (optional Pull Box provides an additional 12 in. of bending space)(a)

Figure 110 - 400 A Main Circuit Breaker, Top Entry, 2.0 Space Factor, with 500 kcmil Burndy Crimp Lugs, 1 per Phase, 300 A Trips (optional Pull Box provides an additional 12 in of bending space)(a)



(a)

(a)


6.90(175.26)

14.36(364.7) 5.15

(130.8)

14.44(366.8)

5.15(130.8)6.90(175.26)

6.90(175.26)

5.15(130.8)

14.44(366.8)

5.15(130.8)6.90(175.26)

14.36(364.7)

Figure 111 - 800 A Frame Main Circuit Breaker, Top Entry, 2.0 Space Factor, with 3/0…350 kcmil Mechanical Lugs, 2 per Phase, 600 A Trips(a)

Figure 112 - 800 A Frame Main Circuit Breaker, Bottom Entry, 2.0 Space Factor, with 3/0…350 kcmil Mechanical Lugs, 2 per Phase, 600 A Trips(a)

Figure 113 - 800 A Frame Main Circuit Breaker, Top Entry, 2.0 Space Factor, with 250…500 kcmil Mechanical Lugs, 2 per Phase, 600 A Trips(a)

Figure 114 - 800 A Frame Main Circuit Breaker, Bottom Entry, 2.0 Space Factor, with 250…500 kcmil Mechanical Lugs, 2 per Phase, 600 A Trips(a)



(a)


Figure 115 - 800 A Frame Main Circuit Breaker, Top Entry, 2.0 Space Factor, with 500 kcmil Panduit Crimp Lugs, 2 per Phase, 600 A Trips (additional 12 in. Pull Box required to meet NEC wire bending requirements)(a)

Figure 116 - 800 A Frame Main Circuit Breaker, Top Entry, 2.0 Space Factor, with 500 kcmil Burndy Crimp Lugs, 2 per Phase, 600 A Trips (additional 12 in. Pull Box required to meet NEC wire bending requirements)(a)



(a)


16.90(430)

5.62(143)

4.93(125)

17.40(442)

5.81(148)

5.06(129)

Figure 117 - 800 A Main Circuit Breaker, Top Entry, 2.5 Space Factor, with #2/0…250 kcmil Mechanical Lugs, 3 per Phase, 800 A Trips(a)

Figure 118 - 800 A Main Circuit Breaker, Bottom Entry, 2.5 Space Factor, with #2/0...350 kcmil Mechanical Lugs, 3 per Phase, 800 A Trips(a)

16.90(430)

6.12(156)5.43(138)

4.81(123)

17.40(442)

4.81(123)

5.43(138)6.12(156)

Figure 119 - 800 A Main Circuit Breaker, Top Entry, 2.5 Space Factor, with #2/0 - 400 kcmil Mechanical Lugs, 3 per Phase, 800 A Trips(a)

Figure 120 - 800 A Main Circuit Breaker, Bottom Entry, 2.5 Space Factor, with #2/0 - 400 kcmil Mechanical Lugs, 3 per Phase, 800 A Trips(a)



(a)


4.18(107)

7.62(194)6.00(153)4.53(115)

3.94(100)

7.62(194)6.00(153)4.53(115)

Figure 121 - 800 A Main Circuit Breaker, Top Entry, 2.5 Space Factor, with 500 kcmil Panduit Crimp Lugs, 3 per Phase, 800 A Trips (additional 12 in. Pull Box required to meet NEC wire bending requirements)(a)

Figure 122 - 800 A Main Circuit Breaker, Top Entry, 2.5 Space Factor, with 500 kcmil Burndy Crimp Lugs, 3 per Phase, 800 A Trips (additional 12 in. Pull Box required to meet NEC wire bending requirements)(a)

Figure 123 - 1200 A Main Circuit Breaker, Top Entry, 3.5 Space Factor, with #4/0 - 500 kcmil Mechanical Lugs, 4 per Phase, 400…1200 Trips(a)

Figure 124 - 1200 A Main Circuit Breaker, Bottom Entry, 3.5 Space Factor, with #4/0 - 500 kcmil Mechanical Lugs, 4 per Phase, 400…1200 Trips(a)



(a)


16.20(412)

9.23(235)

7.73(197)6.30(160)

4.80(122)

16.34(415)

4.80(122)6.30(160)7.73(197)

9.23(235)

15.54(395)

9.23(235)

7.73(197)6.30(160)

4.80(122)

15.68(398)

4.80(122)6.30(160)7.73(122)

9.23(235)

Figure 125 - 1200 A Main Circuit Breaker, Top Entry, 3.5 Space Factor, with 500 kcmil Panduit Crimp Lugs, 3 or 4 per Phase, 400…1200 Trips(a)

Figure 126 - 1200 A Main Circuit Breaker, Bottom Entry, 3.5 Space Factor, with 500 kcmil Panduit Crimp Lugs, 3 or 4 per Phase, 400…1200 Trips(a)

Figure 127 - 1200 A Main Circuit Breaker, Top Entry, 3.5 Space Factor, with 500 kcmil Burndy Crimp Lugs, 4 per Phase, 600…1200 Trips(a)

Figure 128 - 1200 A Main Circuit Breaker, Bottom Entry, 3.5 Space Factor, with 500 kcmil Burndy Crimp Lugs, 4 per Phase, 600…1200 Trips(a)



10.10(256.5)

11.75(298.5)

13.40(340.4)

15.05(382.3)

24.82(630.4)

24.82(630.4)

10.10(256.5)

11.75(298.5)

13.40(340.4)

15.05(382.3)

25.81(655.6)

24.72(627.9)

25.71(653.0)

10.10(256.5)

11.75(298.5)

13.40(340.4)

15.05(382.3)

24.72(627.9)

10.10(256.5)

11.75(298.5)

13.40(340.4)

15.05(382.3)

Figure 129 - 3000 A R-frame Main Circuit Breaker, Top Entry, 8 Cables per Phase

Figure 130 - 3000 A R-frame Main Circuit Breaker, Bottom Entry, 8 Cables per Phase

Figure 131 - 2500 A R-frame Main Circuit Breaker, Top Entry, 100%, 7 Cables per Phase

Figure 132 - 2500 A R-frame Main Circuit Breaker, Bottom Entry, 100%, 7 Cables per Phase



24.86(631.4)

25.85(656.6)

4.61(117.1)

5.77(146.6)

8.47(215.1)

24.82(630.4)

25.81(655.6)

4.61(117.1)5.77(146.6)

8.47(215.1)

24.82(630.4)

4.61(117.1)

5.77(146.6)

24.86(631.4)

4.61(117.1)

5.77(146.6)

Figure 135 - 2000 A and Less R-frame, Top Entry, 6 Cables per Phase

Figure 136 - 2000 A and Less R-frame, Bottom Entry, 6 Cables per Phase

Figure 133 - 2500 A R-frame, Top Entry, 80% 7 Cables per Phase

Figure 134 - 2500 A R-frame, Bottom Entry, 80% 7 Cables per Phase



Conduit Entry - TopFigure 137 - Top View, 20 in. Wide Cabinet, NEMA Type 1 or 12

1.14 17.72

20.00

14.48(367.80)

17.97 (456.44)

20.00 (508.00)

6.63 (168.4)

7.44 (189)

.25 (6.35)

11.09 (281.70)

Load and

Control Wiring

Incoming Line Cables

4.00 (101.60)Wide Internal

VerticalWireway

Front of Cabinet

and Vertical BaffleOptional Horizontal Ground Bus

Note:

Note:Vertical WirewayUsed WhereApplicable

Figure 138 - Top View, 25 in. Wide Cabinet, 100 ms ArcShield

1.14(29.00)

22.72(577.09)

25.00(635.00)

20.00 (508.00)

6.63 (168.40)

0.25 (6.35)

7.44 (189.00)Incoming Line,

Load, and

Control Wiring

and Vertical BaffleHorizontal Ground Bus

Note:

Front of Cabinet

Lift Angle

Pressure Relief Vent




20.00 (508.00)

1.14(29.00)

30.00(762.00)27.72

(704.09)

7.44 (189.00)

0.25 (6.35)

6.63 (168.40) Incoming Line,Load, and

Control Wiring

and Verticle BaffleHorizontal Ground Bus

Note:

Front of Cabinet

Lift Aangle



7.44 (189.00)

0.25 (6.35)

6.63 (168.40)

35.00(889.00)

32.72(803.09)

1.14(29.00)

20.00 (508.00)

Incoming Line,Load, and

Control Wiring

and Vertical BaffleGround BusHorizontal

Note:

Front of Cabinet

Lift Aangle




(a)


Figure 141 - Top Horizontal Ground Bus Location Front View(a)

Figure 142 - Standard and Incoming Line Section, Top Entry, NEMA Type 1, 1 (with gasket), or 12, Single Section, Top View(a)

Dimensions are shown as in. (mm)

Dimension15” Deep 20” Deep

20” Wide

25” Wide

30” Wide

35” Wide

20” Wide

25” Wide

30” Wide

35” Wide

‘A’ 20.00 (508)

25.00 (635)

30.00 (762)

35.00 (889)

20.00 (508)

25.00 (635)

30.00 (762)

35.00 (889)

‘B’ 15.00 (381)

15.00 (381)

15.00 (381)

15.00 (381)

20.00 (508)

20.00 (508)

20.00 (508)

20.00 (508)

‘C’ 17.72 (450)

22.72 (577)

27.72 (704)

32.72 (831)

17.72 (450)

22.72 (577)

27.72 (704)

32.72 (831)

‘D’ 4.38 (111)

9.38 (238) — — 4.38

(111)9.38 (238) — —

‘E’ 7.00 (178)

7.00 (178) — — 7.00

(178)7.00 (178) — —

‘F’ 12.97 (329)

12.97 (329)

12.97 (329)

12.97 (329)

17.97 (456)

17.97 (456)

17.97 (456)

17.97 (456)



(a)


Figure 143 - Standard and Incoming Line Section, Top Entry, NEMA Type 1, 1 (with gasket), or 12, Back-to-Back Construction, Top View(a)

Figure 144 - Standard and Incoming Line Corner Section, Top Entry, NEMA Type 1, 1 (with gasket), or 12, Top View



20” Wide

25” Wide

30” Wide

35” Wide

20” Wide

25” Wide

30” Wide

35” Wide

‘A’ 20.00 (508)

25.00 (635)

30.00 (762)

35.00 (889)

20.00 (508)

25.00 (635)

30.00 (762)

35.00 (889)

‘B’ 29.78 (756)

29.78 (756)

29.78 (756)

29.78 (756)

39.78 (1010)

39.78 (1010)

39.78 (1010)

39.78 (1010)

‘C’ 17.72 (450)

22.72 (577)

27.72 (704)

32.72 (831)

17.72 (450)

22.72 (577)

27.72 (704)

32.72 (831)

‘D’ 4.38 (111)

9.38 (238) — — 4.38

(111)9.38 (238) — —

‘E’ 7.00 (178)

7.00 (178) — — 7.00

(178)7.00 (178) — —

‘F’ 12.97 (329)

12.97 (329)

12.97 (329)

12.97 (329)

17.97 (456)

17.97 (456)

17.97 (456)

17.97 (456)

DimensionSection Depth15”

Wide20”

Wide

‘A’ 25.12 (638)

30.12 (765)

‘B’ 22.75 (578)

27.75 (705)

‘C’ 15.00 (381)

20.00 (508)

‘D’ 7.34 (186)

12.34 (313)

‘E’ 7.41 (188)

12.41 (315)



(a)


Figure 145 - 10 in. Wide Incoming Line Section, Top Entry, NEMA Type 1, 1 (with gasket), or 12, Top View


Wide20”

Wide

‘A’ 14.86 (377)

19.86 (504)

‘B’ 12.71 (323)

17.71 (450)



Conduit Entry - Bottom(a)


Figure 146 - Bottom Horizontal Ground Bus Location, Front View(a)

Figure 147 - Standard and Incoming Line Section, Bottom Entry, NEMA Type 1, 1 (with gasket), or 12, Single Section, Top View(a)



20” Wide

25” Wide

30” Wide

35” Wide

20” Wide

25” Wide

30” Wide

35” Wide

‘A’ 20.00 (508)

25.00 (635)

30.00 (762)

35.00 (889)

20.00 (508)

25.00 (635)

30.00 (762)

35.00 (889)

‘B’ 15.00 (381)

15.00 (381)

15.00 (381)

15.00 (381)

20.00 (508)

20.00 (508)

20.00 (508)

20.00 (508)

‘C’ 17.72 (450)

22.72 (577)

27.72 (704)

32.72 (831)

17.72 (450)

22.72 (577)

27.72 (704)

32.72 (831)

‘D’ 10.00 (254)

12.50 (318)

15.00 (381)

17.50 (445)

10.00 (254)

12.50 (318)

15.00 (381)

17.50 (445)

‘E’ 4.38 (111)

4.38 (111) — — 4.38

(111)4.38 (111) — —

‘F’ 7.00 (178)

7.00 (178) — — 7.00

(178)7.00 (178) — —

‘G’ 11.56 (294)

11.56 (294)

11.56 (294)

11.56 (294)

16.56 (421)

16.56 (421)

16.56 (421)

16.56 (421)

‘H’ 9.13 (232)

9.13 (232)

9.13 (232)

9.13 (232)

14.13 (359)

14.13 (359)

14.13 (359)

14.13 (359)



(a)


Figure 148 - Standard and Incoming Line Section, Bottom Entry, NEMA Type 1, 1 (with gasket), or 12, Back-to-Back Construction, Top View(a)

Figure 149 - Standard and Incoming Line Corner Section, Bottom Entry, NEMA Type 1, 1 (with gasket), or 12, Top View



20” Wide

25” Wide

30” Wide

35” Wide

20” Wide

25” Wide

30” Wide

35” Wide

‘A’ 20.00 (508)

25.00 (635)

30.00 (762)

35.00 (889)

20.00 (508)

25.00 (635)

30.00 (762)

35.00 (889)

‘B’ 29.78 (756)

29.78 (756)

29.78 (756)

29.78 (756)

39.78 (1010)

39.78 (1010)

39.78 (1010)

39.78 (1010)

‘C’ 17.72 (450)

22.72 (577)

27.72 (704)

32.72 (831)

17.72 (450)

22.72 (577)

27.72 (704)

32.72 (831)

‘D’ 10.00 (254)

12.50 (318)

15.00 (381)

17.50 (445)

10.00 (254)

12.50 (318)

15.00 (381)

17.50 (445)

‘E’ 4.38 (111)

4.38 (111) — — 4.38

(111)4.38 (111) — —

‘F’ 7.00 (178)

7.00 (178) — — 7.00

(178)7.00 (178) — —

‘G’ 11.56 (294)

11.56 (294)

11.56 (294)

11.56 (294)

16.56 (421)

16.56 (421)

16.56 (421)

16.56 (421)

‘H’ 9.13 (232)

9.13 (232)

9.13 (232)

9.13 (232)

14.13 (359)

14.13 (359)

14.13 (359)

14.13 (359)


Wide20”

Wide

‘A’ 25.12 (638)

30.12 (765)

‘B’ 21.35 (578)

26.35 (705)

‘C’ 15.00 (381)

20.00 (508)

‘D’ 12.65 (321)

15.15 (385)

‘E’ 7.41 (188)

12.41 (315)



Figure 150 - 10 in. Wide Incoming Line Section, Bottom Entry, NEMA Type 1, 1 (with gasket), or 12 Top View


Wide20”

Wide

‘A’ 14.86 (377)

19.86 (504)

‘B’ 12.71 (323)

17.71 (450)



(a)


Figure 151 - Standard and Incoming Line Section, Bottom Entry, NEMA Type 1, 1 (with gasket), or 12, with Optional External Mounting Channels, Single Section, Top View(a)

Figure 152 - Standard and Incoming Line Section, Bottom Entry, NEMA Type 1, 1 (with gasket), or 12, with Optional External Mounting Channels, Back-to-Back Construction, Top View(a)



20” Wide

25” Wide

30” Wide

35” Wide

20” Wide

25” Wide

30” Wide

35” Wide

‘A’ 20.00 (508)

25.00 (635)

30.00 (762)

35.00 (889)

20.00 (508)

25.00 (635)

30.00 (762)

35.00 (889)

‘B’ 15.00 (381)

15.00 (381)

15.00 (381)

15.00 (381)

20.00 (508)

20.00 (508)

20.00 (508)

20.00 (508)

‘C’ 17.72 (450)

22.72 (577)

27.72 (704)

32.72 (831)

17.72 (450)

22.72 (577)

27.72 (704)

32.72 (831)

‘D’ 10.00 (254)

12.50 (318)

15.00 (381)

17.50 (445)

10.00 (254)

12.50 (318)

15.00 (381)

17.50 (445)

‘E’ 4.38 (111)

4.38 (111) — — 4.38

(111)4.38 (111) — —

‘F’ 7.00 (178)

7.00 (178) — — 7.00

(178)7.00 (178) — —

‘G’ 11.56 (294)

11.56 (294)

11.56 (294)

11.56 (294)

16.56 (421)

16.56 (421)

16.56 (421)

16.56 (421)

‘H’ 8.46 (215)

8.46 (215)

8.46 (215)

8.46 (215)

13.46 (342)

13.46 (342)

13.46 (342)

13.46 (342)



20” Wide

25” Wide

30” Wide

35” Wide

20” Wide

25” Wide

30” Wide

35” Wide

‘A’ 20.00 (508)

25.00 (635)

30.00 (762)

35.00 (889)

20.00 (508)

25.00 (635)

30.00 (762)

35.00 (889)

‘B’ 29.78 (756)

29.78 (756)

29.78 (756)

29.78 (756)

39.78 (1010)

39.78 (1010)

39.78 (1010)

39.78 (1010)

‘C’ 17.72 (450)

22.72 (577)

27.72 (704)

32.72 (831)

17.72 (450)

22.72 (577)

27.72 (704)

32.72 (831)

‘D’ 10.00 (254)

12.50 (318)

15.00 (381)

17.50 (445)

10.00 (254)

12.50 (318)

15.00 (381)

17.50 (445)

‘E’ 4.38 (111)

4.38 (111) — — 4.38

(111)4.38 (111) — —

‘F’ 7.00 (178)

7.00 (178) — — 7.00

(178)7.00 (178) — —

‘G’ 11.56 (294)

11.56 (294)

11.56 (294)

11.56 (294)

16.56 (421)

16.56 (421)

16.56 (421)

16.56 (421)

‘H’ 8.46 (215)

8.46 (215)

8.46 (215)

8.46 (215)

13.46 (342)

13.46 (342)

13.46 (342)

13.46 (342)



Figure 153 - Standard and Incoming Line Corner Section, Bottom Entry, NEMA Type 1, 1 (with gasket), or 12, with Optional External Mounting Channels, Top View

Figure 154 - 10 in. Wide Incoming Line Section, Bottom Entry, NEMA Type 1, 1 (with gasket), or 12, with Optional External Mounting Channels, Top View


Wide20”

Wide

‘A’ 25.12 (638)

30.12 (765)

‘B’ 20.98 (533)

25.98 (660)

‘C’ 15.00 (381)

20.00 (508)

‘D’ 12.65 (321)

15.15 (385)

‘E’ 7.41 (188)

12.41 (315)


Wide20”

Wide

‘A’ 14.86 (377)

19.86 (504)

‘B’ 8.59 (218)

13.59 (345)



Notes:




Additional Resources

These documents contain additional information concerning related products from Rockwell Automation.

You can view or download publications at rok.auto/literature.

Resource DescriptionForm 385 - Motor Control Center Layout and Specification Specific drawings and dimensions for your MCC.Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1 Provides general guidelines for installing a Rockwell Automation industrial system.Product Certifications website, rok.auto/certifications. Provides declarations of conformity, certificates, and other certification details.

http://literature.rockwellautomation.com/idc/groups/literature/documents/in/1770-in041_-en-p.pdf

https://www.rockwellautomation.com/global/detail.page?pagetitle=Product-Certifications&content_type=tech_data&docid=de1cc7d81606981b0f214fed1137f539

www.rockwellautomation.com/literature

Publication 2100-TD018C-EN-P - April 2020Supersedes Publication 2100-TD018B-EN-P - March 2015 Copyright © 2020 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.

Rockwell Automation Support

Use these resources to access support information.

Documentation Feedback

Your comments help us serve your documentation needs better. If you have any suggestions on how to improve our content, complete the form at rok.auto/docfeedback.

Technical Support Center Find help with how-to videos, FAQs, chat, user forums, and product notification updates. rok.auto/support

Knowledgebase Access Knowledgebase articles. rok.auto/knowledgebase

Local Technical Support Phone Numbers Locate the telephone number for your country. rok.auto/phonesupport

Literature Library Find installation instructions, manuals, brochures, and technical data publications. rok.auto/literature

Product Compatibility and Download Center (PCDC)

Get help determining how products interact, check features and capabilities, and find associated firmware. rok.auto/pcdc

Rockwell Automation maintains current product environmental information on its website at rok.auto/pec.

Allen-Bradley, CENTERLINE, expanding human possibility, Rockwell Automation, and Rockwell Software are trademarks of Rockwell Automation, Inc.Trademarks not belonging to Rockwell Automation are property of their respective companies.

Rockwell Otomasyon Ticaret A.Ş. Kar Plaza İş Merkezi E Blok Kat:6 34752, İçerenkÖy, İstanbul, Tel: +90 (216) 5698400 EEE YÖnetmeliğine Uygundur

https://rok.auto/support

https://rok.auto/knowledgebase

https://rok.auto/phonesupport

www.rockwellautomation.com/literature

https://rok.auto/pcdc

http://literature.rockwellautomation.com/idc/groups/literature/documents/du/ra-du002_-en-e.pdf

https://rok.auto/docfeedback

https://rok.auto/pec

https://www.instagram.com/rokautomation/

http://https://www.linkedin.com/company/rockwell-automation

http://https://twitter.com/ROKAutomation

https://www.facebook.com/ROKAutomation/

https://www.rockwellautomation.com/

centerline 2100 motor control centers mains and incoming

Documents