cellecta sound proofing solutions refurbishment brochure may 2012
TRANSCRIPT
-
Y (P2)
CI/SfB
(43)
PART
2010
L
solu
tions
PART
2003
E
solu
tions
PART
2010
L
solu
tions
PART E
Solu
tions
CellectaR
I N N O V A T I O N I N I N S U L A T I O N
Refurbishment & Conversion Projects
Sound Proofing Solutions
Thin floor and wall treatments
Domestic acoustic insulation
Quick and easy to install products
Proven constructions
YELO
fon
fon
FIBREfonfon
DECKfonfon
Scree oarddB HiGYP
Sound Proofing Solutions
-
oCellecta is the UKs N 1 manufacturer of high performance acoustic treatments
and specialist insulation products. For over 20 years, our extensive range of products
has been supplied to all sectors of the construction industry including: house builders,
building contractors, ground workers, screeders, roofers and dryliners.
CellectaR
I N N O V A T I O N I N I N S U L A T I O N
DECKfon, FIBREfon, YELOfon, ScreedBoard and HiGYP are registered trademarks of Cellecta Limited.
YELOfonfon
FIBREfonfon
DECKfonfon
Scree oarddB HiGYP
CellectaR
I N N O V A T I O N I N I N S U L A T I O N
ScreedBoard 28 Acoustic...
3min 43sec
ScreedBoard 20 Overlay...
3min 27sec
TETRiS Structural Flooring..
5min 14sec
Videos News RefurbNew Build More
Cellecta App
Installation animations
Technical data sheets & brochures
Comprehensive product info
Latest Cellecta news
CAD Drawings
New
Cellecta &
The Environment
Global
Warming
Potential
-
Part E Acoustic Building Regulations
Cellectas refurbishment and conversion solutions guide demonstrates how a
number of commonly found separating floor and wall constructions can have
their acoustic performance upgraded with proven, cost effective treatments that
will exceed the demanding acoustic legislative requirements.
What do the Building Regulations require?
To comply with current legislation, all separating floors and walls must be constructed in such a way as to
achieve minimum prescribed acoustic values. Tests must be carried out by an accredited acoustic engineer
to demonstrate compliance.
Refurbishment and conversion projects
Each construction element adopting exactly the same construction must be precompletion tested (PCT) by an
accredited acoustician at a rate of 1:10.
Building Regulation performance requirements
New Build
(1)
Also relevant to Section 5 Noise of the Scottish Building Standards
Airborne sound
(Walls & floors)
Impact sound
(Floors)
Change of use
45 dB (D +C ) nT,w tr
England & Wales
Part requirements E E
Historic Buildings
With some historical buildings undergoing a material change of use it may not be practical to
achieve the prescribed sound performance values. In these cases, Building Control bodies
should be satisfied that everything reasonable has been done to improve the sound
performance of the structure. PCT is normally required and the results submitted accordingly.
Selecting the correct acoustic solution
Each projects acoustic characteristics are different and should be assessed on an
individual basis. Before a solution can be proposed, a number of important facts
need to be established:
Airborne sound tested to BS EN ISO 140-4 1998
Impact sound tested to BS EN ISO 140-7 1998
Precompletion testing (PCT)
Once the information has been gathered, either select one of the solutions given on pages 4 16, or should
the construction not be detailed, contact Cellectas technical team on 08456 717174 with the specific
construction details.
3
Technical Advice 08456 71-71-74 [email protected]
What element(s) are to be addressed: walls floors ceilings? 2
What is the construction makeup of all the walls, floors and ceilings? 3
4 Is the existing ceiling to be retained or upgraded?
5 Are there restrictions on the height of the floor finish and ceiling depth?
1 Is the proposed development deemed to be new build or change of use (including refurbishment)?
New Build &
conversionsTraditional buildings
56 dB (D ) nT,w
EScottish Building Standards
Section 5: 2011
-
Separating timber floors with brick or aggregate block masonry walls
Acoustic floorboards laid on timber subfloor
New ceiling fixed to resilient bars
Item Material
2
13mm thick plaster or 12.5mm plasterboard on dabs (8kg/m )
1
2
3
100mm (min) thick masonry wall (min 1350Kg/m )
Existing floorboards or new 18mm (min) tongue and groove chipboard floorboards screwed to joist
200mm (min) timber floor joists at < 450mm centres
Cell fon 50ecta Micro Slab sound absorption material fitted between floor joists 50mm (t) x 400mm (w)FIBRE
16mm metal resilient bar fixed perpendicular to floor joists at 400mm centres
102
2 layers of 15mm sound block (12.5kg/m each) or similar plasterboards to provide fire integrity, fixed in a
staggered formation to the resilient bars
Gaps filled with acoustic mastic sealant
9
11
Cell fon 50ecta FS
perimeter flanking strip, use to isolate plaster/plasterboard and the skirting from the YELO
acoustic floorboard 6mm x 50mm x 30mm x 2000mm
floating acoustic floorboard laid on a timber subdeck 28mm x 600mm x 1200mm Cell dB 28ecta Scree oard
52dB
Typical airborne(1)
performance
54dB
(3)
Fire resistance
60min
Typical impact(2)
performance
1
2
4
5
6
7
8
9
10
11
3
5mm (min) gap between ceramic floor tiles and skirting board filled with flexible mastic3
(1) (2) (3)
L value. Rw + C value. Fire resistance stated is given as a guide, to ensure Building Regulations are achieved refer, to plasterboard manufacturers specifications.n,w tr
NO
SCREW
S
4
Technical Advice 08456 71-71-74 www.cellecta.co.uk
CellectaR
4
5
6
7
8
RF.01
-
Separating timber floors with brick or aggregate block masonry walls
Resilient layer laid on a timber subfloor
Underfloor heating system installed under low resistance floorboards
New ceiling fixed to resilient bars
Item Material
2
13mm thick plaster or 12.5mm plasterboard on dabs (8kg/m )
3
100mm (min) thick masonry wall (min 1350Kg/m )
Cell fon 8ecta
high performance, acoustic fleece loose laid on subdeck 8mm x 600mm x 1200mm FIBRE
Cell fon 50ecta Micro Slab
sound absorption material fitted between floor joists 50mm (t) x 400mm (w)FIBRE
16mm metal resilient bar fixed perpendicular to floor joists at 400mm centres 10
2
2 layers of 15mm sound block (12.5kg/m each) or similar plasterboards to provide fire integrity, fixed in a
staggered formation to the resilient bars 11
Cell fon 50ecta FS
perimeter flanking angle, use to isolate plaster/plasterboard and the skirting from the YELO
acoustic floorboard 6mm x 50mm x 30mm x 2000mm
low thermal resistance floorboard laid on a timber subdeck 20mm x 600mm x 1200mm Cell dB 20ecta Scree oard
52dB
Typical airborne(1)
performance
54dB
(3)
Fire resistance
60min
Typical impact(2)
performance
1
2
4
5
8
9
11
12
3
5mm (min) gap between ceramic floor tiles and skirting board filled with flexible mastic
NO
SCREW
S
5
Technical Advice 08456 71-71-74 [email protected]
Side view
6
7
10
Gaps filled with acoustic mastic sealant12
(1) (2) (3)
L value. Rw + C value. Fire resistance stated is given as a guide. To ensure Building Regulations are achieved, refer to plasterboard manufacturers specifications.n,w tr
Existing floorboards or new 18mm (min) tongue and groove chipboard flooring screwed to 200mm (min) timber joists
Underfloor heating system routed or moulded insulation board loose laid on acoustic fleece
1
2
4
5
6
7
8
9
3
RF.02
-
Separating timber floors with aircrete block masonry walls
Acoustic wall lining and acoustic floorboards laid on timber subfloor
New ceiling fixed to deep resilient bars
Cell fonecta Baffle stripsFIBRE
(15mm x 75mm x 1200mm), stuck horizontally to the head and foot of the wall
& vertically 600mm centres vertically with grab adhesive
Existing floorboards or new 18mm (min) chipboard floorboards screwed to joist
200mm (min) timber floor joists at < 450mm centres
Cell 30ecta HP 30mm deep metal resilient bar fixed perpendicular to floor joists at 600mm (max) centres
10
2
2 layers of 15mm sound block (12.5kg/m each) or similar plasterboards to provide fire integrity, fixed in a
staggered formation to the resilient bars
Gap filled with acoustic mastic sealant
1
9
11
floating acoustic floorboard laid on a timber subdeck 28mm x 600mm x 1200mm Cell dB 28ecta Scree oard
Cell fon 50ecta FS perimeter flanking angle, used to isolate plaster/plasterboard and the skirting from the YELOacoustic floorboard 6mm x 50mm x 30mm x 2000mm
3
100mm (min) thick aircrete block wall (min 600Kg/m )
3
4
5
7
8
9
10
11
2
Cell fon 50ecta Micro Slab
sound absorption material fitted between floor joists 50mm (t) x 400mm (w)FIBRE
(1) (2) (3)
L value. Rw + C value. Fire resistance stated is given as a guide. To ensure Building Regulations are achieved, refer to plasterboard manufacturers specifications.n,w tr
50dB
Typical airborne(1)
performance
53dB
(3)
Fire resistance
60min
Typical impact(2)
performance
Cell fon 30ecta TMFIBRE
acoustic wall lining (30mm x 1200mm x 2400mm) fixed to wall with H GYPi
acoustic fixings (8 x 105mm) at 600mm centres fixings Cell 105ecta AF
2
1
6Side view
CellectaR
Item Material
4
5
6
7
8
3
2
NO
SCREW
S
RF.03
-
Separating timber floors with brick or aggregate block masonry walls
Acoustic floorboards laid on timber subfloor
New ceiling fixed to resilient bars
]
1
2
3
4
5
6
7
10
Existing floorboards or new 18mm (min) tongue and groove chipboard floor boards, screwed to floor joist
200mm (min) timber floor joists at < 450mm centres
1
2
Cell fonecta
perimeter flanking strip used to isolate plasterboard and skirting from the acoustic floor boardYELO
3
100mm (min) thick masonry wall (min 1350Kg/m )
2
13mm thick plaster or 12.5mm plasterboard on dabs (8kg/m )
Cell fon 50ecta Micro Slab sound absorption material fitted between floor joists 50mm (t) x 400mm (w)FIBRE
Floating acoustic floorboard options (all installed on a timber subdeck):2
17mm x 600mm x 2400mm (7.45kg/m ) + perimeter flanking strip17 fon 5/60 T ESYELO2
26mm x 600mm x 2400mm (13.40kg/m )+ perimeter flanking angle T FS3026 fonYELO2
30mm x 600mm x 2400mm (16.20kg/m )+ perimeter flanking angle T FS30 30 fonYELO
Cellecta
DECKfon
16mm metal resilient bar fixed perpendicular to floor joists at 400mm centres
9
2
2 layers of 15mm sound block (12.5kg/m each) or similar plasterboards to provide fire integrity, fixed in a
staggered formation to the resilient bars
Gap filled with acoustic mastic sealant
8
10
(1) (2) (3)
L value. Rw + C value. Fire resistance stated is given as a guide. To ensure Building Regulations are achieved, refer to plasterboard manufacturers specifications.n,w tr
60min
(3)
Fire resistance
17T 50dB
26T 51dB
30T 51dB
Typical airborne(1)
performance
17T 56dB
26T 57dB
30T 56dB
Typical impact(2)
performance
8
9
7
Side view
Technical Advice 08456 71-71-74 [email protected]
CellectaR
Item Material
3
4
5
6
7
RF.04
-
]Existing floorboards or new 18mm (min) tongue and groove chipboard floorboards, screwed to floor joist
200mm (min) timber floor joists at < 450mm centres
2
Metal frame (MF) ceiling system, 2 layers of 15mm sound block (12.5kg/m each) or similar plasterboards
1
2
5
6
7
9
perimeter flanking strip, used to isolate plaster and the skirting from the acoustic floorboardCell fonecta YELO
3
100mm (min) thick masonry wall (min 1350Kg/m )
Separating timber floors with brick or aggregate block masonry walls
Acoustic floorboards laid on timber subfloor
Existing ceiling retained and new suspended ceiling added
Service void
60min
1
2
4
3
8
9
6
7
2
13mm thick plaster or 12.5mm plasterboard on dabs (8kg/m )
Existing plaster and lath ceiling, with any holes filled with suitable material
sound absorption material fitted between floor joists 50mm (t) x 400mm (w)Cell fon 50ecta Micro Slab FIBRE
Acoustic floorboard options (all installed on a timber subdeck):2
28mm x 600mm x 1200mm (26.00kg/m ) + perimeter flanking angle
Scree oard FSdB 28 fon 50 YELO
(1) (2) (3)
L value. Rw + C value. Fire resistance stated is given as a guide. To ensure Building Regulations are achieved, refer to plasterboard manufacturers specifications.n,w tr
5
(3)
Fire resistance
SB28 54dB
17T 52dB
26T 53dB
30T 53dB
Typical airborne(1)
performance
SB28 52dB
17T 54dB
26T 55dB
30T 54dB
Typical impact(2)
performance
8
Technical Advice 08456 71-71-74 www.cellecta.co.uk
100mm (min)
CellectaR
Item Material
4
3
8
Cellecta
DECKfon
2 17mm x 600mm x 2400mm (7.45kg/m ) + perimeter flanking strip17 fon 5/60 T ESYELO
2 26mm x 600mm x 2400mm (13.40kg/m )+ perimeter flanking angle 26 fon 30T FSYELO
2 30mm x 600mm x 2400mm (16.20kg/m )+ perimeter flanking angle 30 fon 30T FS YELO
RF.05
-
Existing floorboards or new 18mm (min) tongue and groove chipboard floorboards, screwed to floor joist
200mm (min) timber floor joists at < 450mm centres
2
2 layers of 15mm sound block (12.5kg/m each) or similar plasterboards
1
2
5
6
7
9
perimeter flanking strip, used to isolate plaster and the skirting from the acoustic floorboardCell fonecta YELO
3
100mm (min) thick masonry wall (min 1350Kg/m )
Separating timber floors with brick or aggregate block masonry walls
Acoustic floorboards laid on timber subfloor
New suspended ceiling hung off floor joists
60min
1
2
4
3
8
9
6
7
2
13mm thick plaster or 12.5mm plasterboard on dabs (8kg/m )
Metal frame (MF) ceiling system hung off floor joists. 100mm (min) below joists
sound absorption material fitted between floor joists 50mm (t) x 400mm (w)Cell fon 50ecta Micro Slab FIBRE
Acoustic floorboard options (installed on a timber subdeck):2
28mm x 600mm x 1200mm (26.00kg/m ) + perimeter flanking angle
Scree oard FSdB 28 fon 50 YELO
(1) (2) (3)
L value. Rw + C value. Fire resistance stated is given as a guide. To ensure Building Regulations are achieved refer, to plasterboard manufacturers specifications.n,w tr
5
(3)
Fire resistance
SB28 53dB
26T 52dB
Typical airborne(1)
performance
SB28 53dB
26T 56dB
Typical impact(2)
performance
Technical Advice 08456 71-71-74 www.cellecta.co.uk
100mm (min)
CellectaR
Item Material
4
3
8
2
26mm x 600mm x 2400mm (13.40kg/m )+ perimeterCell fon 26 fon 30ecta T FSDECK YELOflanking angle
9
RF.06
-
Separating timber floors with brick or aggregate block masonry walls
Acoustic floorboards laid directly on timber subdeck
Existing ceiling not disturbed
2
13mm thick plaster or 12.5mm plasterboard on dabs (min 8kg/m )
Cell fon 50ecta Micro Slab sound absorption material fitted between floor joists 50mm (t) x 400mm (w)FIBRE2
Existing plaster and lath ceiling (min 16kg/m ) or similar weight in plasterboards to provide fire integrity, fixed to the
joists in a staggered formation.
1
Cell fon 15ecta Ultramat
acoustic mat laid on existing floor boards 15mm x 1000mm x 1200mmDECK
3
100mm (min) thick masonry wall (min 1350Kg/m )
1
2
4
5
3
6
45dB
Typical airborne(1)
performance
59dB
(3)
Fire resistance
30min
Typical impact(2)
performance
Existing or new floorboards screwed to timber floor joists set at < 450mm centres
Technical Advice 08456 71-71-74 www.cellecta.co.uk
! Do not secure the floating floor treatment to the deckCaution
(1) (2) (3)
L value. Rw + C value. Fire resistance stated is given as a guide. To ensure Building Regulations are achieved, refer to plasterboard manufacturers specifications.n,w tr
CellectaR
Item Material
6
2
3
4
5
10
RF.07
-
3
100mm (min) thick masonry wall (min 1350Kg/m )
2
13mm thick plaster or 12.5mm plasterboard on dabs (min 8kg/m )
Cell fon 37ecta T structural acoustic floating floorboard laid directly on joists 37mm x 600 x 2400DECK
Cell fon 50ecta Micro Slab
sound absorption material fitted between floor joists 50mm (t) x 400mm (w)FIBRE
16mm metal resilient bar fixed perpendicular to floor joists at 400mm centres
8
2
2 layers of 15mm sound block (12.5kg/m each) or similar plasterboards to provide fire integrity, fixed in a
staggered formation to the resilient bars
Acoustic mastic sealant
1
2
7
9
Cell fon 5/100ecta ES perimeter flanking strip, use to isolate plaster/plasterboard and skirting from the YELOacoustic floorboard
200mm (min) timber floor joists at < 450mm centres
2
3
4
5
9
6
7
8
52dB
Typical airborne(1)
performance
53dB
(3)
Fire resistance
60min
Typical impact(2)
performance
1
Separating timber floors with brick or aggregate block masonry walls
Acoustic floorboards laid directly on timber floor joists
New ceiling fixed to resilient bars
! Do not secure the floating floor treatment to the joistsCaution
(1) (2) (3)
L value. Rw + C value. Fire resistance stated is given as a guide. To ensure Building Regulations are achieved, refer to plasterboard manufacturers specifications.n,w tr
Technical Advice 08456 71-71-74 [email protected]
Side view
CellectaR
Item Material
3
4
5
6
11
RF.08
-
213mm thick plaster or 12.5mm plasterboard on dabs (8kg/m )
1
2
Cell fon 5/120ecta ES
perimeter flanking strip, used to isolate plaster/plasterboard and skirting from the YELO
acoustic floorboard
3
100mm (min) thick masonry wall (min 1350Kg/m )
Separating timber floors with brick or aggregate block masonry walls
Acoustic floorboards laid directly on timber floor joists
Existing ceiling not disturbed joist fire resistance upgraded
1
2
3
4
5
8
9
7
6
! Do not secure the floating floor treatment to the joistsCaution
Cell fon 50ecta Micro Slab
sound absorption material fitted between floor joists 50mm (t) x 400mm (w)FIBRE
92
Existing plaster and lath ceiling (min 16kg/m ) or similar weight in plasterboards to provide fire integrity,
fixed to the joists in a staggered formation.
100mm wide strips of 12.5mm glass reinforced gypsum board fire protection strips mechanically fixed to both
sides of the floor joists
Sheet of 12.5mm glass reinforced gypsum board cut to suit gap between joists, laid on fire protection strips
200mm (min) timber floor joists at < 450mm centres
(1) (2) (3)
L value. Rw + C value. Fire resistance stated is given as a guide. To ensure Building Regulations are achieved, refer to plasterboard manufacturers specifications.n,w tr
(3)
Fire resistance
60min
Q39 49dB
Q45 49dB
Typical airborne(1)
performance
Q39 59dB
Q45 58dB
Typical impact(2)
performance
12
structural acoustic floating floorboard laid directly on joists39mm x 600 x 2400Quattro 39f
structural acoustic floating floorboard laid directly on joists45mm x 600 x 2400Quattro 45f
Cell fonecta DECK
Technical Advice 08456 71-71-74 www.cellecta.co.uk
CellectaR
Item Material
3
7
8
5
6
4
RF.09
-
Item Material
2
13mm thick plaster or 12.5mm plasterboard on dabs (8kg/m )
Cell fon 5/120ecta ES
perimeter flanking strip, use to isolate plaster/plasterboard and skirting fromYELO
acoustic floorboard
3
100mm (min) thick masonry wall (min 1350Kg/m )
Separating timber floors with brick or aggregate block masonry walls
Acoustic floorboards laid directly on timber floor joists
Existing ceiling not disturbed
1
2
3
4
5
6
(3)
Fire resistance
60min
! Do not secure the floating floor treatment to the joistsCaution
7
98
Existing plaster and lath ceiling
Cell fon 50ecta Micro Slab
sound absorption material fitted between floor joists 50mm (t) x 400mm (w)DECK
200mm (min) timber floor joists at < 450mm centres
(1) (2) (3)
L value. Rw + C value. Fire resistance stated is given as a guide. To ensure Building Regulations are achieved, refer to plasterboard manufacturers specifications.n,w tr
2
2 layers of 12.5mm fire boards (9.8kg/m each) or similar plasterboards to provide fire integrity, fixed in a
staggered formation to the floor joists
Galvanised chicken wire mechanically fixed to the underside of the existing ceiling
9
Q39 49dB
Q45 49dB
Typical airborne(1)
performance
Q39 59dB
Q45 58dB
Typical impact(2)
performance
Cell fonecta DECK
Technical Advice 08456 71-71-74 [email protected]
CellectaR
structural floating floor treatment laid directly on joists 39mm x 600 x 2400Quattro 39f
structural floating floor treatment laid directly on joists 39mm x 600 x 2400Quattro 45f
1
2
3
4
7
8
5
6
13
RF.10
-
21
Item Material
15mm thick service void
Cell fonecta Baffle Strips sound absorption strips 15mm x 75mm x 1200mmFIBRE
2
12.5mm (8kg/m ) plasterboard on dabs
1
2
6
7
Cell fonecta TM 2
composite acoustic wall lining 30mm x 1200mm x 2400mm (15.00kg/m )FIBRE H GYPi 30
3
100mm (min) thick masonry wall brick, concrete block or aircrete block (min 600Kg/m )
13mm (min) plaster finish
Wall floor junction detail Wall ceiling junction detail
100 100100mm 10045 4545 100 100100 45
MW.1 MW.3 MW.4
Brick, aggregate or aircrete block separating/partition walls
Semiindependently fixed composite acoustic wall lining
2
Acoustic wall lining secured to the wall with acoustic fixings (8mm x 105mm) 12 per sheet (min)Cell 105ecta AF
6 7 2
13 13252525
Cell 38ecta AT acoustic edge strip used to isolate wall lining from adjoining floor, walls and ceiling
CellectaR
4
5
3 331
52dB
46dB
10dB
50dB
43dB
7dB
51dB
44dB
8dB
50dB
43dB
7dB
Rw
R + Cw tr
38dB
36dB
BaseMW.1 MW.2 MW.3 MW.4partition
Typical airborne performance
Improvement over
base partition R + Cw tr
Technical Advice 08456 71-71-74 [email protected]
1
Base wall
Patent Pending Acoustic System
7116 26
5
4
5
4
5
4
5
4
3
8
3
8888
14
MW.2
-
Item Material
89mm (min) x 38mm timber stud wall set at 600mm (max) vertical centres
Cell fonecta TM 2 composite acoustic wall lining 30mm x 1200mm x 2400mm (15.00kg/m )FIBRE H GYPi 30
16mm thick metal resilient bar fixed to metal studs at 600mm (max) horizontal centres
1
2
Cell fon 15ecta Micro Slab 15mm x 600mm x 1200mmFIBRE
2
12.5mm (min) thick plasterboard (8Kg/m )
Cell 38ecta AT acoustic edge strip used to isolate wall lining from adjoining floor, walls and ceiling
Wall floor junction detail Wall ceiling junction detail
4 4 2
7
TW.3 TW.4
Timber stud separating/partition walls
Semiindependently fixed composite acoustic wall lining
4689114mm 114 126 8946 4646 46 46
1 2 1 2
7
41 2 4 4 2 41
Sound absorption material fitted between timber studs:
2550mm mineral wool acoustic partition roll (APR)
Cell fon 15ecta Micro Slab fitted between resilient bars 15mm x 600mm x 1200mmFIBRE
Cell fon 50ecta Micro Slab sound absorption material fitted between floor joists 50mm (t) x 400mm (w)FIBRE
54dB
45dB
14dB
58dB
49dB
18dB
60dB
52dB
20dB
56dB
49dB
16dB
Rw
R + Cw tr
40dB
35dB
BaseTW.1 TW.2 TW.3 TW.4
30 minutes
30 minutes
30 minutes
30 minutes
30 minutes
Fire resistance
partition
Typical airborne performance
Fire resistance
Improvement over
base partition R + Cw tr
CellectaR
7
Technical Advice 08456 71-71-74 www.cellecta.co.uk
Base wall TW.1 TW.2
66 85 65 6 6 68
7
3
4
5
6
7
8
15
333
-
95mm 82 70 3030 30 70 4625 70 3042
Wall floor junction detail Wall ceiling junction detail
SW.1 SW.3 SW.4
1
Metal frame separating/partition walls
Directly/semiindependently fixed composite acoustic wall lining
5
Item Material
70mm (min) metal C studs set at 600mm (max) vertical centres
Cell fonecta TM 2 composite acoustic wall lining 30mm x 1200mm x 2400mm (15.00kg/m )FIBRE H GYPi 30
16mm thick metal resilient bar fixed to metal studs at 600mm (max) horizontal centres
1
2
FIBREfon 15 15mm x 600mm x 1200mmMicro Slab
2
12.5mm (min) thick plasterboard (8Kg/m )
Cell 38ecta AT acoustic edge strip used to isolate wall lining from adjoining floor, walls and ceiling
Sound absorption material fitted between metal studs:
25 mineral wool acoustic partition roll (APR)
Standard
partition
1 2 1 2 222
66 6
48dB
45dB
5dB
55dB
46dB
12dB
55dB
46dB
12dB
53dB
45dB
10dB
Rw
R + Cw tr
43dB
34dB
BaseSW.1 SW.2 SW.3 SW.4
30 minutes
30 minutes
30 minutes
30 minutes
30 minutes
Fire resistance
partition
Typical airborne performance
Fire resistance
Improvement over
base partition R + Cw tr
Technical Advice 08456 71-71-74 [email protected]
SW.2
CellectaR
3
4
5
6
31 4 4 4 4 44 3333
16
-
Lightweight partitions built off the
floor joistsStairwell/
communal area
Bath and shower trays Sanitary ware Metal frame partition built off the
structural floor
Timber stud partition 3 31b
Technical Advice 08456 71-71-74 www.cellecta.co.uk
Lightweight internal walls built off the structural
floor must be isolated from the acoustic
floorboards with YELOfon ES or FS strip.
Leave a 510mm expansion gap between the habitable area acoustic floorboards and the communal area floor treatment.
Door thresholds
Baths and shower trays should be built off a
structural floor and MUST be isolated from the
acoustic floorboards and any floor finished. Any
gaps should be sealed with a suitable mastic.
Sanitary ware should be built off a structural floor
and MUST be isolated from the acoustic
floorboards and any floor finished. Any gaps should
be sealed with a suitable mastic.
Lightweight internal walls built off the floor joists
MUST be isolated from the acoustic floorboards
with YELOfon ES or FS strip.
Wall treatments MUST be isolated from the
acoustic floorboards with YELOfon ES or FS strip,
and all gaps sealed with a suitable mastic.
Wall treatments MUST be isolated from the
acoustic floorboards with YELOfon ES or FS strip,
and all gaps sealed with a suitable mastic. .
Lightweight internal walls should be built off the
structural floor deck and MUST be isolated from
the acoustic floorboards with YELOfon ES or FS
strip.
1a
YELOfon ES or FS flanking strip
MUST be placed around floor
perimeter, including around all
walls that are built off the
structural floor
Stairwell /
communal
area
Wall treatment installed before the
floor treatment
Wall treatment installed after the
floor treatment
The acoustic performance of the floor structure will be compromised if the acoustic floorboard is not completely
isolated from the timber joists, subfloor, services, door frames, surrounding walls and their treatments. To address
this risk, each potential problem area needs to be detailed accordingly.
Design & installation details CellectaR
31b 31b32
353531b3431b33
353831b37336
1
2
8
3
4
5
67
17
CellectaR
I N N O V A T I O N I N I N S U L A T I O N
ScreedBoard 28 Acoustic...
3min 43sec
ScreedBoard 20 Overlay...
3min 27sec
TETRiS Structural Flooring..
5min 14sec
Videos News RefurbNew Build More
Cellecta App
Installation animations
Technical data sheets & brochures
Comprehensive product info
Latest Cellecta news
CAD Drawings
New
-
Scree oard dB 28
ScreedBoard 28 is the ultimate acoustic overlay treatment. Its
high density and unique resilient layer provides outstanding
acoustic performance.
lOnly 28mm thick
lHard wearing looks and feels like screed
lInterlocking edges no need for screws
lEasy to cut to size and install
lAccepts ceramic tiles*
Overall board thickness:
Facing thickness:
Resilient layer thickness:
Board dimensions:
Edge Profile:
Weight:
Fixings required:
Jointing adhesive:
Perimeter edge strip:
28mm
20mm ScreedBoard
8mm 70% recycled polyester (PES)
600mm x 1200mm
Interlocking tongue & groove2
18.62kg per sheet 26kg/m
None2
SB adhesive (33m per 1Ltr bottle)
YELOfon FS50
High Density Acoustic Floorboard
Scree oard dB 20
ScreedBoard 20's high density and very low thermal resistance
give it a quick heat response time, making it the ideal floorboard
for underfloor heating systems.
lOnly 20mm thick
lHard wearing looks and feels like screed
lInterlocking edges no need for screws
lExceptionally low thermal resistance
lAccepts ceramic tiles*
Board thickness:
Board dimensions:
Edge Profile:
Weight:
Thermal resistance:
Fixings required:
Jointing adhesive:
Perimeter edge strip:
Associated resilient layer:
20mm
600mm x 1200mm
Interlocking tongue & groove2
18.00kg per sheet 25kg/m2
0.04m /kW
None
SB adhesive 2
(33m per 1Ltr bottle)
YELOfon FS50
FIBREfon 8 8mm x 600mm x
1200mm >70% recycled PES
High Density, Low Thermal Resistance Floorboard
Made from recycled &
Recyclable Materials
Global
Warming
Potential0
Recycled &
Recyclable Material
Global
Warming
Potential0
Product Information
*Screedboards should be sealed with SB Primer prior to adhering ceramic tilesFIBRE
fon fon H GYPi TM30
FIBREfon HiGYP 30TM high density acoustic wall boards dramatically
reduce airborne sound transmission through all types of existing and
new build timber stud, metal frame and masonry walls.
lOnly 30mm thick
lExcellent acoustic performance
lHigh density plasterboard facing
lEasy to cut to size and install
Made from
Recyclable Materials
Global
Warming
Potential0
Board dimensions:
HiGYP thickness:
Absorption layer thickness:
Edge profile:
Weight:
Fixing required:
30mm x 1200mm x 2400mm
15mm
15mm
Square edge (SE) or tapered edge (TE)2
10.74kg per sheet 7.45kg/m
Cellecta AF/105 acoustic fixings
(8mm x 105mm) 12per sheet (min)
Acoustic Wall Lining FIBRE
fon fon Baffle Strips
FIBREfon patent pending Baffle Strips are used to isolate FIBREfon
HiGYP 30TM acoustic boards from the structure wall and absorb
airborne sound within the service cavity.
lOnly 15mm thick
lExcellent acoustic performance
lProduce cavity to run services
Easy to cut to size and install
Made from
Recyclable Materials
Global
Warming
Potential0
Baffle size:
Composition:
Fixing adhesive:
15mm (t) x 75mm (w) x 1200mm (l)
Recyclable wood fibre board
Acoustic mastic or grab adhesive
Acoustic Baffle Strips
CellectaR
NO
SCREW
SNO
SCREW
S
-
DECKfonfonUltramat 15
DECKfon Ultramat 15 high performance underlay is a quick and
easy to lay treatment that will improve the airborne and impact
performance of a floor where there is limited room height.
Only 15mm thick
Easy to cut to size with a sharp knife
Overall matt thickness:
Facing:
Resilient core thickness:
Matt dimensions:
Weight:
Perimeter edge strip:
15mm
Rubberised polymer with fillers
9mm
1000mm x 1200mm2
12.00kg per sheet 10kg/m
None required
High Density Acoustic Mat
FIBREfon Micro Slabs unique soft touch microfibres give the
product very high sound absorption properties. It will be fitted
between joists, in ceiling cavities and partition voids.
Available in two thickness: 15 & 50mm
Only half the thickness required compared to traditional
mineral wool to achieve the same acoustic performance
Itchfree fibres
Supplied precut to suit each application
Made from 70%
Recycled Materials
Global
Warming
Potential0
Thickness available:
Slab dimensions:
Composition:
15mm & 50mm
15 600mm x 1200mm
50mm 400mm x 7.20m (3 slabs per pack)
70% (min) recycled polyester micro fibres
High Performance Sound Absorbing Slab
FIBREfonfon Micro Slab 15 50&
itch
free
Made from
Recycled Materials
Global
Warming
Potential0
Technical Advice: 08456 71-71-74 [email protected]
19
DECKfon fon 17 26 30T T T, &
DECKfon overlay treatments are designed to improve the acoustic
performance of a decked timber floor where a new ceiling is to
installed.
lThree thickness available: 17, 26 & 30mm
lMoisture resistant floorboard
lEasy to cut to size and install
Overall board thickness:
Facing thickness:
Resilient layer thickness:
Board dimensions:
Edge Profile:
Weight:
Perimeter edge strip:
17mm, 26mm & 30mm
17T: 9mm MR MDF,
26T: 18mm P5 Chipboard.
30T: 22mm P5 chipboard
8mm open cell polyurethane
600mm x 2400mm
Tongue & groove2
17T: 10.74kg per sheet 7.45kg/m 2
26T: 19.29kg per sheet 13.40kg/m 2
30T: 23.32kg per sheet 16.20kg/m
17T: YELOfon ES5/60
26T & 30T: YELOfon FS30
Acoustic Overlay Floorboards
DECKfon fon 37 39 45T Quattro , &
DECKfon structural treatments are designed to be laid directly on
the floor joists. 37T will improve the acoustic performance for
timber floor where a new ceiling is to be installed and Quattro 39
or 45 where an existing ceiling is to be retained.
lThree thickness available: 37, 39 & 45mm
lMoisture resistant chipboard
lEasy to cut to size and install
Overall board thickness:
Facing thickness:
Board dimensions:
Edge Profile:
Weight:
Perimeter edge strip:
37mm, 39mm & 45mm
37T: 22mm P5 Chipboard
Q38 & Q45: 18mm P5 Chipboard
600mm x 2400mm
Tongue & groove2
37T: 24.76kg per sheet 17.20kg/m 2
Q39: 27.64kg per sheet 19.20kg/m 2
Q45: 28.80kg per sheet 20.00kg/m
37T: YELOfon ES5/100
Q39 & Q45: YELOfon ES5/120
Structural Deck Acoustic Floorboards
Made from recycled &
Recyclable Materials
Global
Warming
Potential0
Made from recycled &
Recyclable Materials
Global
Warming
Potential0
CellectaR
-
20
Technical Advice 08456 71-71-74 www.cellecta.co.uk
! Failure to install a perimeter flanking strip correctly will result in acoustic failureCaution
The acoustic efficiency of the floor or wall will be adversely affected should acoustic bridging between the
acoustictreatment and the surrounding structures occur (known as flanking transmission).
All floor finishes must be isolated from the surrounding walls (including plaster finish and skirting boards), door
linings, services and other structural elements.
To address acoustic flanking, Cellecta manufactures an extensive range of flexible extruded polyethylene
edge strips to suit each specific treatment.
Eliminating Acoustic Flanking
Acoustic treatment Flanking strip required Flanking strip dimensions
YELOfon 5/100ES
YELOfon 5/60ES
YELOfon 5/120ES
YELOfon 30FS(Profiled flanking strip)
YELOfon 50FS(Profiled flanking strip)
Cell 38ecta AT
(Self adhesive acoustic tape)
5mm (t) x 100mm (h) x 50m (L)
5mm (t) x 60mm (h) x 50m (L)
5mm (t) x 120mm (h) x 50m (L)
6mm (t) x 30mm (w) x 30m (h) x 2000mm (L)
6mm (t) x 50mm (w) x 30m (h) x 2000mm (L)
2.5mm (t) x 38mm (w) x 40m (L)
DECKfon 37T
DECKfon 17T
DECKfon 26T
DECKfon 30T
Scree oard dB 28
H GYPi 30TM
Note. All Cellecta edge strips have a global warming potential (GWP) of
-
Tools & Accessories
ScreedBoard Fixing Batten
ScreedBoard Pull Bar
SB Adhesive 1 litre bottle2
Coverage: 33m /ltr of ScreedBoard
Cellecta fon Adhesive 1 litre bottle2
Coverage: 33m /ltr of acoustic boards
ScreedBoard Primer 5 litre bottle
Use to seal the Screedboards prior to
adhering ceramic tiles
Cellecta HP30 Deep Resilient Bar
Size: 30mm deep x 3000mm long
Installation centres: > 600mm centres
The resistance to airborne sound depends mainly on the mass per unit area of the structural floor and supporting
walls, and partly on the ceilings construction. It is therefore important to choose a ceiling treatment that
complements the performance of the chosen structural floor, to produce an overall structure that exceeds the
required values. Decoupling the ceiling from the structural floor is an effective way of reducing the contact path
that impact sound can follow. Adding mass in the way of plasterboard to the floor structure and filling the ceiling
void with a mineral wool will also improve the acoustic performance of the structure.
Detailed below are for four types of ceiling treatments available in order of performance:
Ceiling Treaments
Notes. Further guidance is given in Approved Document E and the manufacturer of the proposed ceiling system. Professional advice should be sought
to ensure the overall floor construction complies with current fire regulations.
2: Proprietary metal frame suspended ceiling system
Cavity filled with 50mm FIBREfon Micro Slab 50 or3
100mm mineral wool (45kg/m ).
1: Independent ceiling
Cavity filled with 50mm FIBREfon Micro Slab 503
or 100mm mineral wool (45kg/m ).
3: Plasterboard on Cellecta HP30 deep resilient bars
Cavity filled with 50mm FIBREfon Micro Slab 503
or 100mm mineral wool (45kg/m ).
4: Plasterboard on proprietary shallow resilient bars
Cavity filled with 50mm FIBREfon Micro Slab 50 or 3
100mm mineral wool (45kg/m ).
Up to 450mm centres
Up to 600mm centres
Technical Advice 08456 71-71-74 [email protected]
CellectaR
21
-
Construction Information & Notes
Further Information CellectaR
External wall type:
New Build Refurbishment/conversionType of project: Mixed development
Brick/ dense block with cavity Brick/aircrete block with cavity Solid 9" Brick/dense block
Other (details)
Internal wall type: Brick/ dense block Timber stud Metal frame
Floor type: Solid timber joists Other (details)
Ceiling: Existing ceiling to be retained New ceiling to be installed
Proposed ceiling construction:
Further information:
Floor depth: mm
Aircrete block
Wall finish: Plastered None Other (details)Plasterboard on dabs
Installation
Cellecta acoustic insulation products are supplied with
detailed fixing instructions. For further assistance contact
Cellectas technical team on Tel. 08456 717174.
Architectural Drawings
Architects and designers can quickly and easily insert
Cellectas insulation products into their drawings by
downloading the specific FASTRACK detail in dwg CAD
format from Cellectas website.
Specification Clauses
Specifiers can quickly and easily insert Cellectas
insulation products into their specification document by
downloading the relevant RIBA NBS Plus clause from
Cellectas website (www.cellecta.co.uk).
Health and Safety
Copies of COSHH data for all Cellecta products are
available upon request.
Packaging
Cellecta acoustic boards are strapped and shrink
wrapped on wooden pallets with corner protectors. Micro
slabs are suppled in polythene bags.
Onsite handling & storage
Cellecta acoustic boards must be stored on level ground, in a
dry environment, undercover and not sheeted outside.
Technical Advice 08456 71-71-74 [email protected]
Notes
Cellecta reserves the right to amend product specifications without prior notice. Colours shown are for illustration purposes and are subject to production
variation. Product technical data stated is typical. The information included in this guide is based on Cellectas experience and is believed to be reliable. dB values
quoted and applications illustrated are typical, however, each sites characteristics are different and as a result, reliance should not be solely placed upon the
recommendations detailed.
Cellecta, as the manufacturer, has no control over the installation of its products. The purchaser should evaluate the product's suitability and is responsible for
adhering to any laws or regulations in this respect, making the purchaser also liable for observing any third party rights.
22
-
Other Products Available From Cellecta
Technical Advice 08456 71-71-74 [email protected]
23
YELO 10fon fon HD + System
YELO HD10+ is the acclaimed high density, closedcell resilient layer system (YELO HD10+, fon fon
Estrip and Jstrip) that carries its own proprietary Robust detail EFC5. The lightweight, easy to
install system delivers unrivalled acoustic performance when used to isolate a floating screed from
a structural concrete separating floor.
Superior impact sound deadening properties
Suitable for all types of concrete floors and screeds
Lightweight, easy to cut and install rolls
Robust detail treatment (EFC5) 2
Over 5,000,000m successfully installedRecyclable Material
Global
Warming
Potential
-
Technical Helpline:Technical, installation advice,
site surveys and takeoff service
T: 08456 717174
F: 08456 717172
Unit D Norman Close
Rochester
Kent
ME2 2JU
T. 08456 717174
F. 08456 717172
www.cellecta.co.uk
CellectaI N N O V A T I O N I N I N S U L A T I O N
R
ARB/612/V2
FASTRACKCADARCHITECTURAL CAD DATABASES
R
Plus