cedar creek™ shake and north ridge™ slate true nature · cedar creek shake and north ridge...

CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE

CEDAR CREEK™ SHAKE

INSTALLATION INSTRUCTIONS

NORTH RIDGE™ SLATE

TRUENATURE

METAL ROOFING

Inspired by NatureEngineered by Vicwest

TRUE NATURE METAL ROOFING


TABLE OF CONTENTS PAGE

Important Notice / Safety / Storage / Warranty 1Product Overview 2Trims 3Accessories / Tools – Glossary 4 - 5Roof Preparation 6Fastening 7Installation Procedure Summary 8Shake and Slate Installation Step-by-Step- Layout 9 Installation Details 10 Eave 11 Gable 12 Trim Overlap Details 13 Non-Vented Ridge Cap Detail 14 Vented Ridge Detail 15 Hip Detail without Under Hip Flashing 16 Hip Detail with Under Hip Flashing Hip/Ridge Cap 18 Ridge Cap Detail at Gable End 19 Hip Cap Detail at Eave 20 Under Hip Trim 21 Valley 22 Valley Trim 23 Roof Slope Transition 24 Endwall New Construction 25 Endwall Re-Roof / Existing Cladding Construction 26 Endwall Re-Roof / Existing Masonry Construction 27 Sidewall New Construction 28 Sidewall Re-Roof / Existing Wall Construction 29 Sidewall Re-Roof / Existing Masonry Construction 30 Roof Vent/Pipe Detail 31 Chimney High End Detail 32 Chimney Sidewall Detail 33 Chimney Low End Detail 34 Chimney Trims Installation Steps 35 - 36 Chimney Trims Cutting/Bending 37 Side / End Wall Overlap 38 Reglet Trim 39



Page 1 of 39

IMPORTANT NOTICEThe installation guidelines for True Nature Cedar Creek Shake (Shake) and True Nature North Ridge Slate(Slate) metal roof tiles are intended only as a guide for product handling and installation procedures.The materials and methods indicated herein are specified to help maintain overall integrity of the roofingsystem.These guidelines do not address all aspects of the roofing installation or custom roof design requirements.Each specific roof and its construction may require variations from the information in this guideline. Thequality of the installation is ultimately reliant on the experience and workmanship of the roofing contractor.These instructions shall be used as guidelines only and Vicwest assumes no responsibility whatsoeverregarding improper installation or improper use of its products.If you have any questions, please contact your local authorized Vicwest representative. For furtherinformation visit www.vicwest.com.

SAFETYFollow all governmental safety guidelines.The installer/owner of the roof system is responsible to adhere to safe installation practices mademandatory by provincial and/or local ordinances as well as good construction practices.Wearing of appropriate clothing, protective eyewear, light soft-soled shoes, safety gloves, as well asgovernment approved fall arrest equipment are recommended.Maintaining good housekeeping and keeping roof clear of debris as you work is a key ingredient to thesafety of the project.When walking on the roof, use soft-soled, non-marking shoes that will better grip the surface of the tileas well as protect the painted finish. When stepping on the tiles place your foot in the center, not onthe interlocking edges or the tile nosing.

STORAGEShake and Slate tiles and accessories must be stored in a dry, ventilated area protected from moistureand chemicals. It is recommended to install the tile as soon as possible after purchase.

WARRANTYPlease refer to www.vicwest.com for warranty information on the Shake and Slate tile and register yourwarranty when your project is completed.



Page 2 of 39

WEEP HOLES

EFFECTIVE COVERAGE

EFFE

CTIV

E CO

VER

AG

EEF

FECT

IVE

COV

ERA

GE

4'-2 3/4”

50”

12”

1'-1

9/1

6”

4'-2 11/16”

50”

1'-1

9/16

”

12”

11

1'-15/8”

6 7/16”

TOP-LOCK

TOP-LOCK

FASTENING TRACK

NOSE

EFFECTIVE COVERAGE

EFFECTIVE COVERAGE

SIDE-LOCK

KEYWAY

TOP-LOCK

FASTENING TRACK

NOSE

SIDE-LOCK

KEYWAY WEEP HOLES

PRE-DRILLED HOLES FOR FASTENING


DIVERTER

FASTENING TRACK


BUILDING PRODUCTS

TRUE NATURE COLLECTION

Shake / Slate Series

SHAKE

SLATE

HIP/RIDGE CAP

15/16”

PRODUCT OVERVIEWInstalled Coverage/Exposure Size: 12” x 50” / tileInstalled Coverage/Exposure Area: 4.17 sqft / tile (24 tiles per square)Installed Weight: 3.76 lbs / tile (90 lbs/square)Tile Depth: 9/16” at the tile noseMaterial: 28ga (0.015”), Grade 33, galvalume coated steel



Page 3 of 39

CL

BUILDING PRODUCTS

SHAKE/SLATE ROOF SERIES

FLASHING SKETCHES

EAVE

UNDER HIP

VALLEY

END WALL

Z-FLASHING

REGLET

OUTER GABLE INNER GABLE

Flashings are 10'-0", 28ga (0.015”), Grade 33, Galvalume coated steel

SIDE WALL

SIDE WALL MASONRY END WALL MASONRY

SLOPE CHANGE/TRANSITION

PREPAINTED/EXPOSED SIDE

HIGH END CHIMNEY

TRIMS

The True Nature Trim System is manufactured to suit a majority of installation types but on-site modifications of degrees may be required to suit your specific project needs. Customized trims and flat sheets are also available.



Page 4 of 39

BUILDING PRODUCTS


ACCESSORIES

ACCESSORY DESCRIPTIONIMAGE

BLACK, GREY (EPDM)FLEXIBLE PIPE FLASHINGROOF VENT/PIPE SEAL

5/8" x 11 1/2" x 20' ROLL

RIDGE ROOF VENT NYLON 6” PLUS CARBON BLACK FOR

URETHANE / SILICONE SEALANTOR COLOUR MATCHED

1/8"x1/2"x25' LONG

COLOUR MATCHEDEPDM BONDED WASHER

#10 x 1 1/2" LG. PANCAKE HEAD,SELF TAPPING, TYPE 'A'

HIDDEN FASTENER, ZINC PLATED

#10 x 1" LG PANHEAD, PHILIPS DRIVESELF TAPPING, TYPE 'A'

EXPOSED FASTENER, ZINC-PLATED


UV RESISTANCE, NON-WOVEN NYLON-POLYESTER WEATHER BARRIER

FOAM SEALERCLOSED CELL

#8-18 x 3/4" LG. HEX WASHER HEAD, SELF DRILLING, NO. 3 PT, C/W

#10 x 3" LG. HEX HEAD, SELF TAPPING TYPE 'A'

EXPOSED, UV RESISTANT, CLEAR

BUTYL SEALANT NON-EXPOSED, NON-SKINNING,

BUTYL TAPE

COLOUR MATCHED

EXPOSED FASTENER, ZINC-PLATED

NON-DRYING, FLEXIBLE

NON-EXPOSED, NON-SKINNING,NON-DRYING FLEXIBLE

3/4"x1"x20' LONG

#10 x 1 1/2" LG. HEX HEAD,SELF TAPPING, TYPE 'A'


HIDDEN FASTENER, ZINC PLATED #10 x 1 1/2" LG. HEX HEAD,SELF TAPPING, TYPE 'A' C/WEPDM BONDED WASHER

ACCESSORIES



Page 5 of 39

BUILDING PRODUCTS


ACCESSORIES

FITS ALL HAND DRILLS

RECOMMENDED TOOLS: CORDLESS DRILL, CIRCULAR SAW, TIN SNIPS, CHALK LINE, SQUARE, TAPE MEASURE.

ACCESSORY DESCRIPTIONIMAGE

HT SELF-ADHERED UNDERLAYMENT

SYNTHETIC UNDERLAYENT

HIGH PERFORMANCE SELF-ADHESIVE, HIGH TEMPERATURE UNDERLAYMENT FOR METAL ROOFS

HIGH TEMPERATURE WOVEN SYNTHETIC ROOF UNDERLAYMEN.

FOLDING TOOL

TSHD TURBO SHEAR

PORTABLE SHEET METAL BRAKE FOR FORMING FLASHINGS AND TILES

FOR SMALL AREAS

true shear image and description from Steve

TRUE CUT SHEARFOR CUTTING METAL TILES

ACCESSORIES



Page 6 of 39

ROOF PREPARATION

Roof SlopeShake and Slate tiles to be used on 3:12 roof slope or greater.Do not install Shake and Slate tiles on roof slopes less than 3:12.Refer to underlayment requirements below for roof slopes at 3:12 and greater than 4:12.

UnderlaymentFollow your local building code and manufacturer’s guidelines for the underlayment requirements, overlapsand installation procedures.• For roof slopes of 3:12 up to under 4:12 install high temperature self-adhered underlayment on entire roof

coverage.• For roof slopes of 4:12 or greater we recommend using high temperature self-adhered underlayment in the

areas that experience most driving rain, snow accumulation or ice damming. In all other areas use synthetic underlayment or #30 felt. See ‘Installation Procedure Summary’ below.

• If required, use underlayment primer on the roof sheathing to ensure proper adherence of the high temperature self-adhered underlayment.

Roof Deck/SheathingIt is recommended to install Shake and Slate tiles on minimum ½” plywood sheathing but no less thanrequired by your local building code.

Roof SquarenessThe installation guidelines assume that the roof is square. Always check the roof squareness first.

New ConstructionPrepare the roof deck to meet local building codes.

Re-Roof ConstructionIt is always recommended to remove the old asphalt shingles before installing the Shake and Slate metal roofing. Inspect existing roof sheathing and underlayment for any deterioration or damage in preparation to meet the local building codes.

Although Vicwest always recommends removing existing asphalt shingles from the roof deck, Shake and Slate may be installed over one layer of asphalt shingles. High quality synthetic underlayment must be applied under the new metal tiles and over the existing asphalt shingles. All foreign materials, damaged or curled tiles must be removed before installation of our metal tiles. Longer fasteners will be required when applying the metal tile on this type of installation. Any imperfection on roof may transmit it through the tile. This is a natural cause and is not a reason for rejection of the product.

When installing new underlayment clear the roof surface from protruding nails, staples or any other debris that could potentially puncture the underlayment. Replacement of existing roof sheathing and underlayment may be required.



Page 7 of 39

7 x FASTENERS PER TILE

4 x FASTENERS PER TILE

BUILDING PRODUCTS



FASTENING

• Fasten tile panels with specified fasteners through the pre-punched holes.• Standard fastening requires 4 fasteners per tile #10 x 1 1/2” LG. HEX HEAD, SELF TAPPING, TYPE ‘A’.• In high-wind areas use 7 fasteners per tile in all areas within 3’ of the roof perimeter (around the eaves,

gables and ridge/hips).• Self-tapping screws must penetrate the wood sheathing by minimum 3/8” below the sheathing.• Self-drilling screws must penetrate beyond metal substrate a minimum of 3 pitches of thread.



Page 8 of 39

SHAKE/SLATE ROOF SERIESBUILDING PRODUCTS ISOMETRIC

SYNTHETIC

HT SELF ADHERED UNDERLAYMENT

TYPICAL ROOF UNDERLAYMENT LAYOUT

INSTALLATION PROCEDURE SUMMARY

1. Check that the existing eave line is straight before starting the eave trim installation. Use a chalk line to mark a straight line across the eave if required. Do not depend on the existing roof edge to be straight or square.

2. Install eave trim.3. Install high temperature self-adhered underlayment along the eave on top of the eave trim.4. Install high temperature self-adhered underlayment in valley, on hips, at slope transitions, end walls, side

walls, around chimneys, skylights and at any roof penetrations, or as required per local building code.5. Install synthetic underlayment on the remaining areas on the entire roof.6. Install inner & outer gable trims.7. Install valley flashing.8. Install end wall & side wall trims.9. Install hip flashing (optional)10. Install Shake/Slate tiles starting at bottom left corner of the roof, proceeding from left to right and from

bottom up. Ensure that keyways and side-locks are staggered.11. Install hip/ridge caps.



Page 9 of 39

January 8, 2020 [VW Version 2.1] – DRAFT Page 13 of 46

11”

22”

33”

Full Tile

Full Tile

Full Tile

Full Tile

Full Tile

Full Tile Full TileFIFTH COURSE(REPEAT OF ONE)

FOURTH COURSE

THIRD COURSE

SECOND COURSE

FIRST COURSE

ERECTION DIRECTION

FULL SHEET

THIRD CUT

SECOND CUT

FIRST CUT

FULL SHEET

GA

BLE

TRUE NATURE METAL ROOFING Cedar Creek Shake & North Ridge Slate


SHAKE LAYOUT PATTERN

11”

22”

33”

Full Tile

Full Tile

Full Tile

Full Tile

Full Tile

Full Tile Full Tile

SHAKE STAGGERED LAYOUT

Trim the first tile of each course at 11”, 22” and 33” respectively from the edge of the right side lock.


12”

24”

36”

Full Tile

Full Tile

Full Tile

Full Tile

Full Tile

Full Tile Full TileFIFTH COURSE(REPEAT OF ONE)

FOURTH COURSE

THIRD COURSE

SECOND COURSE

FIRST COURSE

ERECTION DIRECTION

FULL SHEET

THIRD CUT

SECOND CUT

FIRST CUT

FULL SHEET

GA

BLE

SLATE STAGGERED LAYOUT

Trim the first tile of each course at 12”, 24” and 36” respectively from the edge of the right side lock.



Page 10 of 39


BUILDING PRODUCTS ISOMETRIC

GF

H

D

I

KB

E

C

A

B

JL

ABCDEF

G

IJKL

H

TYPICAL ROOF CONDITION LAYOUT

EAVE - pg 11GABLE - pg 12VENTED OR NON-VENTED RIDGE - pg 14-15UNDER HIP - pg 21VALLEY - pg 22END WALL - pg 25-27

SIDE WALL - pg 28 - 30 SLOPE CHANGE/TRANSITION - pg 24

HIGH END CHIMNEY - pg 32

SIDE WALL MASONRY - pg 30END WALL MASONRY - pg 27

ROOF VENT/PIPE - pg 31

SHAKE AND SLATE INSTALLATION DETAILS



Page 11 of 39

ROOF SHEATHING

FASCIA BOARD

EAVE TRIM

SHAKE/SLATE TILE

HT SELF-ADHERED UNDERLAYMENT OVER EAVE TRIM

1. Eave Trim to be installed on straight line and square to ensure straight edge for the first row of roof tiles. Chalk line the top position of the Eave Trim to accommodate the most prominent outward point of the fascia board, if required.

2. Fasten Eave Trim every 12”.

3. Install HT Self-adhered underlayment strip over Eave Trim, as per local building code.

4. Ensure that the first row of roof tiles is tightly hooked over the Eave Trim and installed at a straight line.

#10 x 1 1/2" LG, PANCAKE-HEAD, TYPE 'A' SCREW@12" O/C


BUILDING PRODUCTS Shake / Slate Series

EAVE DETAIL WITH OVERHANG

EAVE

1. Eave Trim to be installed on straight line and square to ensure straight edge for the first row of roof ties. Chalk line the top position of the eave trim to accommodate the most prominent outward point of the fascia board, if required.

2. Fasten eave trim every 12” using #10 x 1 1/2” LG, PANCAKE-HEAD, TYPE ‘A’ SCREW.

3. Install high temperature self-adhered underlayment strip over eave trim, as per local building code.

4. Ensure that the first row of roof tile is tightly hooked over the eave trim and installed at a straight line.

CUT 1" SLIT FOR EXPANSION

1" MIN

ROOF SLOPE

BOTTOM TRIM

TOP TRIM

OPEN HEM AS REQUIRED FOR OVERLAP

BUILDING PRODUCTS





Page 12 of 39

31 2"

GABLE BOARD

ROOF SHEATHING

OUTER GABLE

INNER GABLE

SYNTHETIC UNDERLAYMENT

SHAKE/SLATE SHINGLE

#10 x 1 1/2" LG, HEX-HEAD,

TYPE 'A' SCREW, C/W EPDM BONDED WASHER

@16" O/C

1. Position Inner Gable Trim flush with the gable board.

2. Install Inner Gable Trim over top of the Eave Trim and fasten in the outer trough at every 16". Do not screw

into the inner trough.

3. Hook Outer Gable over the Inner Gable.

4. Stagger overlap joints of the Inner and Outer Gable Trims.

5. Fasten Outer Gable to the fascia board at every 16”.

INNER GABLE 'BLADE'

INNER TROUGH

OUTER TROUGH

INNER GABLE

#10 x 1" LG, PANHEAD TYPE 'A' SCREWS

@16" O/C

OUTER GABLE 'BLADE'

OUTER GABLE

1" CUT-OUT

AT EAVE PANEL NOSING

SHAKE/SLATE SHINGLE

DIVERTER

DIVERTER

BUILDING PRODUCTS



GABLE DETAIL GABLE

1. Position inner gable trim flush with the gable board.2. Install inner gable trim over top of the eave trim and fasten in the outer trough at every 16” using #10 x 1 1/2”

LG, HEX-HEAD, TYPE ‘A’ SCREW WITH EPDM BONDED WASHER. Do not screw into the inner trough.3. Hook outer gable over the inner gable.4. Stagger overlap joints of the inner and outer gable trims.5. Fasten outer gable to the fascia board at every 16” using #10 x 1” LG, PANHEAD TYPE ‘A’ SCREWS.



Page 13 of 39

2" MIN

CUT TRIM AT ANGLE

1"

ROOF SLOPE

BOTTOM TRIM

TOP TRIM

BUILDING PRODUCTS

TRUE NATURE COLLECTIONShake / Slate Series

INNER GABLE TRIM

2" MINOVERLAP

ROOF SLOPE

TRIM OVERLAP DETAILS

INNER GABLE TRIM

BOTTOM TRIM

TOP TRIM

2" MIN

ROOF SLOPE


BUILDING PRODUCTS


OUTER GABLE TRIM

2 ROWS OFBUTYL CAULKING

2" MINOVERLAP

ROOF SLOPE

OUTER GABLE TRIM


2" MIN

ROOF SLOPE


STAGGER/OFFSET OVERLAPS OF INNER AND OUTER GABLE TRIMS

BUILDING PRODUCTS

INNER AND OUTER GABLE TRIM LAP DETAIL

INNER AND OUTER GABLE TRIM LAP DETAIL



Page 14 of 39

RIDGE/HIP CAP

ROOF SHEATHING

1. Cut the top row of roof shingles at the ridgeline and fasten with 7 equally spaced fasteners to the roof sheathing.

2. Apply con�nuous foam-sealer on top of shingles along the ridge. Ensure that the foam-sealer is posi�oned on the outside edge of the Ridge Cap, in front of the Ridge Cap fasteners.

3. Align Ridge Cap along the ridge. Use chalk line if required.

4. Install Ridge Cap with 3" long screws through the pre-punched slo�ed holes. Do not overdrive fasteners.

2"

5"

RIDGE CAP FASTENER#10 x 3" LG, HEX-HEAD, TYPE 'A'

SYNTHETIC UNDERLAYMENT

FOAM SEALER

SHAKE/SLATE SHINGLE

#10 x 1 1/2" LG, HEX-HEAD, TYPE 'A' SCREW, C/W EPDM BONDED WASHER @ 7 PER SHINGLE

BUILDING PRODUCTS


NON-VENTED RIDGE DETAIL

NON-VENTED RIDGE DETAIL

1. Cut the top row of roof tiles at the ridgeline and fasten with 7 equally spaced #10 x 1 1/2” LG, HEX-HEAD, TYPE ‘A’ WITH EPDM BONDED WASHER fasteners to the roof sheathing.2. Apply continuous foam-sealer on top of tiles along the ridge. Ensure that the foam-sealer is positioned on the

outside edge of the ridge cap, in front of the ridge cap fasteners.3. Align ridge cap along the ridge. Use chalk line if required.4. Install ridge cap with #10 x 3” LG, HEX-HEAD, TYPE ‘A’ through the pre-punched slotted holes. Do not overdrive fasteners.



Page 15 of 39

RIDGE/HIP CAP

RIDGE ROOF VENT

ROOF SHEATHING

1. Cut 2” of roof sheathing at the ridge, or as per your local building code.

2. The underlayment should not extend over the cut opening. This is important to maintain un-obstructed ventilation.

3. Cut the top row of roof shingles at the edge of sheathing and fasten with 7 equally spaced fasteners.

4. Apply butyl sealant on the shingle along the ridge and adhere the vented ridge roll to the shingle. Use chalk line if required.

5. Align Ridge Cap along the ridge.

6. Install Ridge Cap with 3" long screws through the pre-punched slotted holes. Do not overdrive fasteners.

2"

5"

RIDGE CAP FASTENER#10 x 3" LG, HEX-HEAD, TYPE 'A'

RAFTERSRIDGE BEAM

1"

SHAKE/SLATE SHINGLE


BUILDING PRODUCTS



VENTED RIDGE DETAIL

VENTED RIDGE DETAIL

1. Cut 2” of roof sheathing at the ridge, or as per your local building code.2. The underlayment should not extend over the cut opening. This is important to maintain unobstructed

ventilation.3. Cut the top row of roof tiles at the edge of sheathing and fasten with 7 equally spaced #10 x 1 1/2” LG, HEX-

HEAD, TYPE ‘A’ WITH EPDM BONDED WASHER fasteners.4. Apply butyl sealant on the tile along the ridge and adhere the vented ridge roll to the tile. Use chalk line if

required.5. Align ridge cap along the ridge.6. Install ridge cap with #10 x 3” LG, HEX-HEAD, TYPE ‘A’ fasteners through the pre-punched slotted holes. Do not overdrive fasteners.



Page 16 of 39

1"

RIDG

E CA

P

ROOF

SH

EET

1. Install HT Self-adhered underlayment along the hip, or as required per local building code.

2. Cut, fold and overlap the Shake/Slate shingle over the hip centerline by a minimum 2" onto the opposite side of prevailing winds.

3. Fasten the roof shingle overlap with 2 screws per shingle.

4. Apply continuous foam-sealer on top of the shingles along the hip. Ensure that the foam-sealer is positioned on the outside edge of the Hip Cap, in front of the Hip Cap fasteners.

5. Align Hip Cap along the hip centerline. Use chalk line if required.

6. Install Hip Cap with 3" long screws through the pre-punched slotted holes. Do not overdrive fasteners.


FOLD SHINGLE OVER THE HIP LINE BY MIN 2"

FOAM SEALER


2"HIP CAP FASTENER#10 x 3" LG, HEX-HEAD,TYPE 'A'

2"

OVERLAP

RIDGE/HIP CAP

SHAKE/SLATE SHINGLE

PREVAILING WINDS

BUILDING PRODUCTS



HIP DETAIL WITHOUT HIP UNDER-FLASHING (OPTIONAL)

HIP DETAIL WITHOUT UNDER HIP FLASHING

1. Install high temperature self-adhered underlayment along the hip, or as required per local building code.2. Cut, fold and overlap the Shake/Slate tile over the hip centerline by a minimum 2” onto the opposite side of

prevailing winds.3. Fasten the roof tile overlap with 2 #10 x 1 1/2” LG, HEX-HEAD,TYPE ‘A’ SCREW WITH EPDM BONDED

WASHER, per tile.4. Apply continuous foam-sealer on top of the tiles along the hip. Ensure that the foam-sealer is positioned on

the outside edge of the hip cap, in front of the hip cap fasteners.5. Align hip cap along the hip centerline. Use chalk line if required.6. Install hip cap with #10 x 3” LG, HEX-HEAD, TYPE ‘A’ screws through the pre-punched slotted holes. Do not overdrive fasteners.



Page 17 of 39

RIDGE/HIP CAP

ROOF SHEATHING

1. Install HT Self-adhered underlayment along the hip.

2. Align Hip Flashing on the hip and install over top of Eave Trim.

3. Cut the end of Hip Flashing on angles to match the two adjoining eave sec�ons.

4. Fasten Hip Flashing in the outer trough at every 16". Do not screw into the inner trough.

5. Cut the Shake/Slate shingles along the hip centerline and fasten to the roof sheathing, outside of Hip Under-Flashing

6. Apply con�nuous foam-sealer on top of the shingles along the hip. Ensure that the foam-sealer is posi�oned on the outside edge of the Hip Cap, in front of the Hip Cap fasteners.

7. Align Hip Cap along the hip centerline. Use chalk line if required.

8. Install Hip Cap with 3" long screws through the pre-punched slo�ed holes. Do not overdrive fasteners.

2"

HT SELF-ADHEREDUNDERLAYMENT

HIP UNDER FLASHING

DIVERTER

HIP FLASHING

OUTER TROUGH

INNER TROUGH

FOAM SEALER

#10 x 1 1/2" LG, HEX-HEAD, TYPE 'A' SCREW, C/W EPDM BONDED WASHER @ 16" O/C

HIP CAP FASTENER#10 x 3" LG, HEX-HEAD,TYPE 'A'


DIVERTER

SHAKE/SLATE SHINGLE

BUILDING PRODUCTS


HIP DETAIL WITH HIP UNDER FLASHING HIP DETAIL WITH UNDER HIP FLASHING (OPTIONAL)

1. Install high temperature self-adhered underlayment along the hip.2. Align hip flashing on the hip and install over top of eave trim.3. Cut the end of hip flashing on angles to match the two adjoining eave sections.4. Fasten hip flashing in the outer trough at every 16” using #10 x 1 1/2” LG, HEX-HEAD, TYPE ‘A’ SCREW WITH

EPDM BONDED WASHER. Do not screw into the inner trough.5. Cut the Shake/Slate tiles along the hip centerline and fasten to the roof sheathing TYPE ‘A’ SCREW WITH

EPDM BONDED WASHER outside of hip under-flashing6. Apply contiuous foam-sealer on top of the tiles along the hip. Ensure that the foam-sealer is positioned on

the outside edge of the hip cap, in front of the hip cap fasteners.7. Align hip cap along the hip centerline. Use chalk line if required.8. Install hip cap with#10 x 3” LG, HEX-HEAD, TYPE ‘A’ fasteners through the pre-punched slotted holes. Do not

overdrive fasteners.



Page 18 of 39

7"

11.85"

1. Align Shake/Slate Ridge/Hip Cap along the ridge or hip. Use chalk line if required.

2. Install Ridge/Hip Cap with 3" long wood screws through the center of the pre-punched slotted holes. Do not overdrive fasteners.

3. Ensure Ridge/Hip caps are tightly hooked into the lock and installed in straight line.

4. Note: On roof pitches greater than 12:12 Ridge Hip Cap requires snip at nosing and fastening track to allow for overbending of cap.

2"

S-LOCK


RIDGE/HIP CAP FASTENERS#10 x 3" LG, HEX-HEAD, TYPE 'A'

SNIP CAP NOSING TO ALLOW BENDING

SNIP FASTENING TRACK AND DIVERTER TO ALLOW BENDING

BUILDING PRODUCTS



RIDGE/HIP CAP

12:12 Ridge Diagram

HIP/RIDGE CAP

1. Align Shake/Slate Hip/Ridge Cap along the ridge or hip. Use chalk line if required.2. Install hip/ridge cap with #10 x 3” LG, HEX-HEAD, TYPE ‘A’ FASTENERS through the center of the pre-

punched slotted holes. Do not overdrive fasteners.3. Ensure hip/ridge caps are tightly hooked into the top lock and installed in straight line.4. Note: On roof pitches greater than 12:12 hip/ridge cap requires snip a v-cut at nosing and fastening track to

allow for overbending of the cap (refer to diagram).



Page 19 of 39

1. Snip Ridge/Hip Cap edges as shown and fold-in.

2. Snip the middle of the ridge cap approximately 1" along the center.

3. You may need to snip the line on a small angle depending on roof pitch so the trim can fold over.

4. Fold front tab into hem and bend at gable edge to 90 degrees.

a. The cap should sit outside the gable trim

b. Fasten the turned down cap edges to the gable trim with #10 x 1" LG Panhead, type 'A' screws

RIDGE CAP FOLDED OVER GABLE

#10 x 1" LG., PANHEAD TYPE 'A' SCREWS(COLOUR TO MATCH)

SNIP CAP BACK1" MIN, IN A V-CUT

FOLD LINE

FOLD IN FOR HEM3" M

IN

CUT LINE

FOLD IN

CUT LINE

ROOF LINE/GABLE EDGE

ROOF LINE/GABLE EDGE

3" MIN

MIN 1"

CUT OUTER EDGE TOFIT OVER GABLE TRIM

RIDGE/HIP CAP

SHAKE/SLATESHINGLE

1"

BUILDING PRODUCTS



RIDGE CAP DETAIL AT GABLE END

RIDGE CAP DETAIL AT GABLE END

1. Snip ridge cap edges as shown and fold in.2. Snip the middle of the ridge cap approximately 1” along the center.3. You may need to snip the line on a small angle depending on roof pitch so the trim can fold over.4. Fold front tab into hem and bend at gable edge to 90 degrees. a) The cap should sit outside the gable trim b) Fasten the turned down cap edges to the gable trim with colour matched #10 x 1” LG panhead,

type ‘A’ screws



Page 20 of 39

HIP CAP DETAIL AT EAVE

1. Mark the underside of the hip cap along the angle of the eave edge. This is your marked cut line.2. From the marked cut line, measure 2 more fold lines at 5/8” and 1/2” apart. 3. Note: You may be required to increase the spacing between the fold lines when using the under hip flashing

option. 4. Cut at the 1st fold line on the outer edge of hip cap.5. Snip a v-cut in the middle of the hip cap along the centre crease. a) Fold front tab into hem and bend at eave edge to match eave b) Fasten the turned down cap edges to the tile nose with #10 x 1” LG, panhead, type ‘A’ screws.6. Install the remainder of hip/ridge caps in a straight line.

1. Mark the angle of the eave on the underside of the Ridge/Hip Cap.

2. From the scribed line, mark 2 more fold lines at 58" and 1

2" apart. Note: 1" may be required for large metal build-up when using Hip Under Flashing option.

3. Cut at the 1st fold line on the outer edge of hip cap.

4. Snip a “V” in the middle of the Ridge/Hip Cap along the centre crease.

a. Fold front tab into hem and bend at eave edge to match eave

b. Fasten the turned down cap edges to the shingle nose with #10 x 1" LG, Panhead, type 'A' screws.

5. Install the remainder of Ridge/Hip Caps in a straight line.

BUILDING PRODUCTS



HIP CAP DETAIL AT EAVE

EAVE EDGE

FOLD LINES

MARKED CUT LINE

OFFCUT

FORMED NOSE OFHIP CAP AT EAVE

5/8”1/2”

1/2”

5/8”

V-CUT AT CENTER



Page 21 of 39

TOP TRIM

BOTTOM TRIM

2" MIN

ROOF SLOPE

FOLD OUT EDGES TO ALLOW TOP TRIM TO NEST INSIDE BOTTOM TRIM

2 ROWS OF BUTYL CAULKING

BUILDING PRODUCTS


Shake / Slate SeriesHIP TRIM

UNDER HIP TRIM



Page 22 of 39

1. Install HT self-adhered underlayment in the valley.

2. Align Valley flashing on the valley and position over Eave trim.

3. Cut the end of Valley flashing on angles matching the two adjoining eave sections and installed cut edge at 1" up from eave edge.

4. Push the Valley flashing tight into the roof and fasten in the outer trough at every 24".

5. Cut the metal shingle to fit the valley angle.

6. Refer to tile notching/folding instructions.

INNER TROUGH

OUTER TROUGHDIVERTER

CL

1-PIECE VALLEY FLASHING

ROOF SHEATHING


VALLEY FLASHING FASTENER #10 x 1 1/2" LG, HEX-HEAD, TYPE 'A' SCREW, C/W EPDM BONDED WASHER @ 24" O/C

3"CUT-OUT AT EAVE PANEL NOSING

SHINGLE FASTENER #10 x 1 1/2" LG, HEX-HEAD, TYPE 'A' SCREW

SHAKE/SLATE SHINGLE

SHAKE/SLATE SHINGLE

BUILDING PRODUCTS

VALLEY



36" HT SELF-ADHERED UNDERLAYMENT EXTEND 18" UP & DOWN FROM TRANSITION POINT

VALLEY

1. Install high temperature self-adhered underlayment in the valley.2. Align valley flashing on the valley and position over eave trim.3. Cut the end of valley flashing on angles matching the two adjoining eave sections and installed cut edge at 1”

up from eave edge.4. Push the valley flashing tight into the roof and fasten in the outer trough at every 24” using #10 x 1 1/2” LG,

HEX-HEAD, TYPE ‘A’ SCREW, EPDM BONDED WASHER.5. Cut the metal tile to fit the valley angle.6. Refer to tile notching/folding instructions.



Page 23 of 39

CONT. BUTYL CAULKING ACROSS LAP

CUT FLASHING ON ANGLE 6" BACK

6" MIN

TOP TRIM

BOTTOM TRIM

ROOF SLOPE

6" OVERLAP

6" MIN

SNIP AND FOLD WATER DIVERTER BACK FOR OVERLAP

CONT. BUTYL CAULKING

INSERT BUTYL CAULKING INTO CUT WING


BUILDING PRODUCTS


Shake / Slate Series VALLEY TRIM

VALLEY TRIM



Page 24 of 39

UPPER SHAKE/ SLATE SHINGLE

ROOF TRANSITION TRIM

LOWER SHAKE/SLATE SHINGLE


ROOF SHEATHING

36" HT SELF-ADHERED UNDERLAYMENT EXTEND 18" UP & DOWN FROM TRANSITION POINT

1. Apply HT Self-adhered underlayment, along transi�on roof line.

2. Measure and cut shingle 2" above the roof pitch change. Bend shingle to suit slope change.

3. Fasten lower roof shingle with 7 equally spaced fasteners to the roof sheathing.

4. Apply foam-sealer 2" below roof pitch change on the lower roof shingles.

5. Fasten Roof Transi�on Trim to the lower roof shingle through foam sealer at every 16".

6. Set Starter Trim on butyl tape on the upper roof slope, on top of Roof Transi�on Trim and fasten every 12".

7. Install first course of Shake/Slate shingle on the upper roof slope.

#8-18 x 3/4" LG. MAX., HWH NO. 2 PT. W/ NEOPRENE WASHER AT 16" O/C

FOAM SEALER

2"

BUTYL TAPE

STARTER TRIM

#10 x 1 1/2” LG. HEX-HEAD TYPE 'A' SCREW, C/WEPDM BONDED WASHER@ 12" O/C

2"

BUILDING PRODUCTS

ROOF SLOPE TRANSITION


#10 x 1 1/2" LG, PANCAKE-HEAD,TYPE 'A' SCREW @12" O/C

FROM THE PITCH CHANGE ADD LAYER OF SYNTHETIC UNDERLAYMENT BELOW THE HT S/A

FROM THE PITCH CHANGE ADD LAYER OF SYNTHETIC UNDERLAYMENT BELOW THE HT S/A

ROOF SLOPE TRANSITION

1. Apply high temperature self-adhered underlayment, along transition roof line.a) It is important to put the high temperature self-adhered underlayment on top of the

syntheticunderlayment on the lower roof slope.b) It is important to put the high temperature self-adhered underlayment under the synthetic

underlayment on the upper roof slope.2. Measure and cut tile 2” above the roof pitch change. Bend tile to suit slope change.3. Fasten lower roof tile with 7 X #10 x 1 1/2” LG, HEX-HEAD, TYPE ‘A’ SCREW with EPDM BONDED WASHER

equally spaced fasteners to the roof sheathing.4. Apply foam-sealer 2” below roof pitch change on the lower roof tiles.5. Fasten roof transition trim to the lower roof tile through foam sealer at every 16” using #8-18 x 3/4” LG. MAX.,

HWH NO. 2 PT. W/ NEOPRENE WASHER6. Set starter trim on butyl tape on the upper roof slope, on top of roof transition trim and fasten every 12” using

#10 x 1 1/2” LG, PANCAKE-HEAD, TYPE ‘A’ SCREW7. Install first course of Shake/Slate tile on the upper roof slope.



Page 25 of 39

END WALL TRIM

EXTERIOR CLADDING

CARRY 6” HT SELF-ADHERED UNDERLAYMENT UP WALL ASSEMBLY

1. Apply HT Self-adhered underlayment at least 6” up the endwall.

2. Measure and cut shingle with a min 12" fold up at the base of the wall.

3. Set Z-flashing in butyl sealant on top of shingle and fasten into plywood with 7 equally spaced fasteners per shingle .

4. Hook Endwall Transition Trim over Z-flashing and fasten at every 16” to the end-wall substrate.

5. Apply continuous sealant at base of Z-flashing.

6. Apply underlayment strip over the transition trim behind new wall cladding.

#10 x 1 1/2” LG. MAX., HEXHEAD TYPE 'A' SCREW, C/W EPDM BONDED WASHER

UNDERLAYMENT STRIP OVER END WALL

1/2” MIN FOLD-UPON LAST COURSE OF SHINGLES

CONTINUOUS BUTYL SEALANT

CONTINUOUS URETHANE/SILICONE SEALANT

Z-FLASHING

#10 x 1 1/2” LG. PANCAKE HEAD (TYP.)@ 16" O/C

#10 x 1 1/2” LG. MAX., HEXHEAD TYPE 'A' SCREW

SHAKE/SLATE SHINGLE

BUILDING PRODUCTS

ENDWALL



NEW CONSTRUCTION ENDWALLNEW CONSTRUCTION

1. Carry high temperature self-adhered underlayment at least 6” up the endwall.2. Measure and cut tile with a min 1/2” fold up at the base of the wall for last couple of tiles.3. Set Z-flashing in butyl sealant on top of tile and fasten into plywood with 7 equally spaced #10 x 1 1/2” LG.

MAX., HEX HEAD TYPE ‘A’ SCREW, C/W EPDM BONDED WASHER per tile.4. Hook end wall trim over Z-flashing and fasten with #10 x 1 1/2” LG. PANCAKE HEAD every 16” to the end-wall substrate.5. Apply continuous urethane/silicone sealant at base of Z-flashing.6. Apply underlayment strip over the transition trim behind new exterior cladding.

PLEASE REFERENCE PAGE 38 FOR SIDE / END WALL OVERLAP DETAILS



Page 26 of 39

1/2” MIN FOLD-UP


REGLET TRIM

ENDWALL TRANSITION TRIM

EXISTING CLADDING


#10 x 1 1/2" LG, HEX-HEAD, TYPE 'A' SCREW, C/W EPDM BONDED WASHER

CONTINUOUS SEALANT UNDERLAYMENT STRIP OVER ENDWALL TRANSITION TRIM

1. Ensure that HT Self-adhered underlayment is installed at wall to roof transition as required.

2. Measure and cut shingle with a min 12" fold up at the base of the wall .


4. Hook Endwall Transition Trim over Z-flashing and fasten every 16” to the face of existing wall cladding.

5. Apply continuous sealant at base of Z-flashing .

6. Apply underlayment strip over the Endwall Transition Trim and onto the face of existing wall.

7. Install Reglet Trim over the underlayment strip and fasten every 12".

8. Apply continuous sealant along the top edge of the Reglet Trim.

Z-FLASHING

CONT. SEALANT

#10 x 1" LG PANHEAD TYPE 'A' SCREW @ 12" O/C

#10 x 1 1/2” LG. PANCAKE HEAD @ 16" O/C

#10 x 1 1/2" LG, HEX-HEAD, TYPE 'A' SCREW

SHAKE/SLATE SHINGLE

BUILDING PRODUCTS

ENDWALL



RE-ROOF / EXISTING WALL CONSTRUCTION

ENDWALLRE-ROOF / EXISTING CLADDING CONSTRUCTION

1. Carry high temperature self-adhered underlayment at least 6” up the endwall.2. Measure and cut tile with a min 1/2” fold up at the base of the wall for last course of tiles.3. Set Z-flashing in butyl sealant on top of tile and fasten into plywood with 7 equally spaced #10 x 1 1/2” LG.

MAX., HEX HEAD TYPE ‘A’ SCREW, WITH BONDED WASHER per tile.4. Hook end wall trim over Z-flashing and fasten with #10 x 1 1/2” LG. PANCAKE HEAD every 16” to the face of exiting cladding.5. Apply continuous urethane/silicone sealant at base of Z-flashing.6. Apply 2” strip of high temperature underlayment over the end wall trim and onto the face of existing

cladding.7. Install reglet trim over the underlayment strip and fasten every 12” using #10 x 1” LG PANHEAD TYPE ‘A’

SCREW8. Apply continuous sealant along the top edge of the reglet trim.

PLEASE REFERENCE PAGE 38 FOR SIDE / END WALL OVERLAP DETAILSPLEASE REFERENCE PAGE 39 FOR REGLET TRIM DETAILS



Page 27 of 39

END WALL MASONRY TRIM


CONT. SEALANT IN GROOVE

1/2” MIN FOLD-UP




4. Cut groove in masonry for Endwall Reglet Trim installation.

5. Apply continuous sealant along groove in masonry, and apply butyl tape on top of Z-flashing.

6. Hook Endwall Reglet Trim over Z-flashing and embed into sealant in the masonry groove.

7. Fasten Endwall Reglet Trim to Z-flashing with pop-rivets every 24".


CONTINUOUSBUTYL SEALANT

Z-FLASHING

CONTINUOUS SEALANT


POP-RIVETS AT 24" O/C

BUTYL TAPE

ROOF SHEATHING

SHAKE/SLATE SHINGLE


BUILDING PRODUCTS

ENDWALL



RE-ROOF / EXISTING MASONRY CONSTRUCTION

EXISTING MASONRY CONSTRUCTION

ENDWALLRE-ROOF / EXISTING MASONRY CONSTRUCTION

1. Carry high temperature self-adhered underlayment is installed at wall to roof transition as required.2. Measure and cut tile with a min 1/2” fold up at the base of the wall for last couple of tiles.3. Set Z-flashing in butyl sealant on top of tile and fasten into plywood with 7 equally spaced #10 x 1 1/2” LG,

HEX-HEAD, TYPE ‘A’ SCREW, C/W EPDM BONDED WASHER per tile.4. Cut groove in masonry for end wall masonry installation.5. Apply continue urethane/silicone sealant along groove in masonry, and apply butyl tape on top of Z-flashing.6. Hook end wall masonry over Z-flashing and embed into sealant in the masonry groove.7. Fasten end wall masonry to Z-flashing with pop-rivets every 24”.8. Apply continuous sealant at base of Z-flashing.




Page 28 of 39

CARRY UNDERLAYMENT 6” UP WALL SUBSTRATE

SIDE WALL TRIM

INNER GABLE TRIM

EXTERIOR CLADDING

1. Apply HT Self-adhered underlayment at least 6” up the sidewall.

2. Install Inner Gable Trim along the sidewall and attach in the outer trough at every 12”.

3. Hook Sidewall Transition Trim tight onto Inner Gable and fasten at every 12” to the sidewall substrate.

4. Apply underlayment strip over the Sidewall Transition Trim behind new wall cladding.

5. Slide shingles into the Inner Gable Trim .

CARRY MEMBRANE OVER SIDE WALL

#10 x 1 1/2” LG. PANCAKE HEAD, TYPE'A' SCREW @ 16" O/C

#10 x 1 1/2" LG, HEX-HEAD, TYPE 'A' SCREW, C/W EPDM BONDED WASHER@ 12" O/C

2 1/2”SHAKE/SLATE SHINGLE

BUILDING PRODUCTS

SIDEWALL



NEW CONSTRUCTION SIDEWALLNEW CONSTRUCTION

1. Apply high temperature self-adhered underlayment at least 6” up the sidewall.2. Install inner gable trim along the sidewall and attach in the outer trough at every 16” using #10 x 1 1/2” LG.

PANCAKE HEAD, TYPE ‘A’ SCREW3. Hook side wall trim tight onto inner gable and fasten at every 12” using #10 x 1 1/2” LG, HEX-HEAD, TYPE ‘A’

SCREW to the sidewall substrate.4. Apply underlayment strip over the side wall trim behind new wall cladding.5. Slide tiles into the inner gable trim.




Page 29 of 39


SIDE WALL TRIM

INNER GABLE TRIM

CONTINUOUS SEALANT

EXISTING CONSTRUCTION

UNDERLAYMENT STRIP OVER SIDE WALL TRIM


2. Install Inner Gable trim along the existing sidewall and attach in the outer trough at every 12".

3. Hook Sidewall Transition Trim tight onto Inner Gable and fasten at every 12" to the sidewall.

4. Apply underlayment strip over Sidewall Transition Trim and onto the face of existing sidewall.

5. Install Reglet Trim over the underlayment strip and fasten every 16".

6. Apply continuous sealant along the top edge of the Reglet Trim.


REGLET TRIM

2 1/2”

#10 x 1" LG PANHEAD TYPE 'A' SCREW @ 12" O/C

#10 x 1 1/2” LG. PANCAKE HEAD @ 16" O/C


SHAKE/SLATE SHINGLE

BUILDING PRODUCTS



SIDEWALL

RE-ROOF / EXISTING WALL CONSTRUCTION

SIDEWALLRE-ROOF / EXISTING WALL CONSTRUCTION

1. Ensure that high temperature self-adhered underlayment is installed at wall to roof transition as required.2. Install inner gable trim along the existing sidewall and attach in the outer trough at every 12” with #10 x 1 1/2”

LG, HEX-HEAD, TYPE ‘A’ SCREW, C/W WITH BONDED WASHER.3. Hook side wall trim tight onto inner gable and fasten to the sidewall every 16” using #10 x 1 1/2” LG.

PANCAKE HEAD.4. Apply underlayment strip over side wall trim and onto the face of existing sidewall.5. Install reglet trim over the underlayment strip and fasten every 12” using #10 x 1” LG PANHEAD TYPE ‘A’

SCREW.6. Apply continuous Urethane/silicone sealant along the top edge of the reglet trim.7. Slide tiles into the inner gable trim.

PLEASE REFERENCE PAGE 38 FOR SIDE / END WALL OVERLAP DETAILS PLEASE REFERENCE PAGE 39 FOR REGLET TRIM DETAILS



Page 30 of 39

SIDE WALL MASONRY

INNER GABLE TRIM


CONTINUOUS SEALANT IN GROOVE


2. Install Inner Gable trim along the existing sidewall and attach in the outer trough every 12"

3. Cut groove in masonry for Sidewall Reglet Trim installation.

4. Apply continuous sealant along groove in masonry and apply butyl tape on top of Inner Gable Trim.

5. Hook Sidewall Reglet Trim over Inner Gable and embed into sealant in the masonry groove.

6. Fasten Sidewall Reglet Trim to Inner Gable with pop-rivets at every 24".


2 1/2”



BUTYL TAPE


SHAKE/SLATE SHINGLE

BUILDING PRODUCTS



SIDEWALL

RE-ROOF / EXISTING MASONRY CONSTRUCTION

SIDEWALLRE-ROOF / EXISTING MASONRY CONSTRUCTION

1. Ensure that high temperature self-adhered underlayment is installed at wall to roof transition as required.2. Install inner gable trim along the existing sidewall and attach in the outer trough every 12” #10 x 1 1/2” LG,

HEX-HEAD, TYPE ‘A’ SCREW, C/W EPDM BONDED WASHER3. Cut groove in masonry for side wall masonry trim installation.4. Apply continuous sealant along groove in masonry and apply butyl tape on top of inner gable trim.5. Hook side wall masonry trim over inner gable and embed into sealant in the masonry groove.6. Fasten side wall masonry trim to inner gable with pop-rivets at every 24”.7. Slide tiles into the inner gable trim.




Page 31 of 39

ROOF VENT/PIPESILICONE SEALANT BETWEEN FLEXIBLE PIPE FLASHING AND ROOF VENT/PIPE

#8 x 18 x 3/4" LG. HEX WASHER HEAD, SELF DRILLING, NO. 3 PT, C/W NEOPRENE WASHERS

NEW OR EXISTING SHEATHING

SILICONE SEALANT BETWEEN FLEXIBLE PIPE FLASHING AND METAL ROOF, UNDER PERIMETER FLANGE

FLEXIBLE PIPE FLASHING

1. Measure size of pipe/stack and cut required diameter of boot to suit.

2. Install self-adhered underlayment around the perimeter of the base of the pipe/stack.

3. Apply a generous amount of sealant from the topside of the pipe/stack forming the shape of a “U”.

4. Install the Flexible Pipe Flashing following the manufactures installation guideline.

Potential use of a snow break may be required over the pipe or stack. Please consult your local representative for more information.


SHAKE/SLATE SHINGLE


BUILDING PRODUCTS



ROOF VENT/PIPE DETAIL

ROOF VENT/PIPE DETAIL

1. Measure size of pipe/stack and cut required diameter of boot to suit.2. Install self-adhered underlayment around the perimeter of the base of the pipe/stack.3. Apply a generous amount of sealant from the topside of the pipe/stack forming the shape of a “U”.4. Install the flexible pipe flashing following the manufactures installation guideline.

Potential use of a snow break may be required over the pipe or stack. Please consult your local representative formore information.



Page 32 of 39

1. Ensure that HT self-adhered underlayment is installed up the masonry wall.

2. Install Inner Gable Trim against the masonry wall and attach in the outer trough at every 24”.

3. Cut groove in masonry for High End Reglet Trim installation.

4. Install shingles into the Inner Gable.

5. Apply continuous sealant along masonry groove.

6. Install High End Reglet into lap of second shingle course and embed into sealant in the masonry. Fasten to masonry at 12" O/C.

7. Apply continuous sealant at the High End Reglet Trim at the shingle lap.

8. Refer to 'Chimney Trims Installation Steps' for sealant locations at Reglet trims intersections at chimney corners.

ROOF SHEATHING

MASONRY

HIGH END CHIMNEY

INNER GABLE TRIM

FIELD SNIP AND FOLD PANEL END


FLASHING TO TERMINATE UNDER LAP OF 2ND PANEL FROM CHIMNEY


CONTINUOUS SEALANT



SHAKE/SLATE SHINGLE

BUILDING PRODUCTS



CHIMNEY HIGH END DETAIL

CHIMNEY HIGH END DETAIL

1. Ensure that high temperature self-adhered underlayment is installed up the masonry wall.2. Install inner gable trim against the masonry wall and attach in the outer trough at every 24” using #10 x 1 1/2”

LG, HEX-HEAD, TYPE ‘A’ SCREW, C/W EPDM BONDED WASHER3. Cut groove in masonry for high end chimney trim installation.4. Install tiles into the inner gable.5. Apply continuous sealant along masonry groove.6. Install high end chimney trim into lap of second tile course and embed into sealant in the masonry. Fasten to

masonry with standard masonry screws every 12” O/C.7. Apply continuous sealant at the high end chimney trim at the tile lap.8. Refer to ‘Chimney Trims Installation Steps’ for sealant locations at masonry trims intersections at chimney

corners.




Page 33 of 39

1. Ensure that HT Self-adhered underlayment is installed at the roof to chimney transition as required.

2. Install Inner Gable trim along the chimney sidewall and attach in the outer trough every 16"

3. Cut groove in masonry for Sidewall Reglet Trim installation.

4. Apply continuous sealant along groove in masonry and butyl tape on top of Inner Gable Trim.

5. Hook Sidewall Reglet Trim over Inner Gable and embed into sealant in the masonry groove.

6. Fasten Endwall Reglet Trim to Inner Gable with pop-rivets at every 24".


SIDE WALL MASONRY

INNER GABLE TRIM



2 1/2”



BUTYL TAPE#10 x 1 1/2" LG, HEX-HEAD, TYPE 'A' SCREW, C/W EPDM BONDED WASHER@ 16" O/C

SHAKE/SLATE SHINGLE

ROOF SHEATHING


CHIMNEY SIDEWALL DETAIL


CHIMNEY SIDEWALL DETAIL

1. Ensure that HT Self-adhered underlayment is installed at the roof to chimney transition as required.2. Install inner gable trim along the chimney sidewall and attach in the outer trough every 16” using #10 x 1 1/2”

LG,HEX-HEAD, TYPE ‘A’ SCREW, C/W EPDM BONDED WASHER3. Cut groove in masonry for side wall masonry trim installation.4. Apply continuous sealant along groove in masonry and butyl tape on top of inner gable trim.5. Hook side wall masonry trim over inner gable and embed into sealant in the masonry groove.6. Fasten side wall masonry trim to inner gable with pop-rivets at every 24”.7. Slide tiles into the inner gable trim.




Page 34 of 39

END WALL MASONRY

EXISTING CONSTRUCTION (MASONRY)


CONT. SEALANT IN GROOVE

1/2” MIN FOLD-UP

CONTINUOUSBUTYL SEALANT

Z-FLASHING

CONTINUOUS SEALANT


BUTYL TAPE

ROOF SHEATHING

1. Ensure that HT Self-adhered underlayment is installed at roof to chimney transition as required.



4. Cut groove in masonry for Endwall Reglet Trim installation.

5. Apply continuous sealant along groove in masonry, and apply butyl tape on top of Z-flashing.

6. Hook Endwall Reglet Trim over Z-flashing and embed into sealant in the masonry groove.

7. Fasten Endwall Reglet Trim to Z-flashing with pop-rivets every 24".


SHAKE/SLATE SHINGLE



CHIMNEY LOW END DETAIL


CHIMNEY LOW END DETAIL

1. Ensure that high temperature self-adhered underlayment is installed at roof to chimney transition as required.

2. Measure and cut tile with a min 1/2” fold up at the base of the wall .3. Set Z-flashing in butyl sealant on top of tile and fasten into plywood with 7 equally spaced #10 x 1 1/2” LG,

HEX-HEAD, TYPE ‘A’ SCREW, WITH EPDM BONDED WASHER fasteners per tile.4. Cut groove in masonry for end wall masonry trim installation.5. Apply continuous sealant along groove in masonry, and apply butyl tape on top of Z-flashing.6. Hook end wall masonry trim over Z-flashing and embed into sealant in the masonry groove.7. Fasten end wall masonry trim to Z-flashing with pop-rivets every 24”.8. Apply continuous sealant at base of Z-flashing.



Page 35 of 39

TYPICAL ROOF CHIMNEY

SHAKE OR SLATE ROOF SHINGLE

TYPICAL ROOF CHIMNEY

ROOF SHEATHING WITH HT SELF-ADHERED UNDERLAYMENT

INNER GABLE CONTINUOUS AROUND OPENING (EXCEPT BOTTOM)

INNER GABLE CONTINUOUS AROUND OPENING (EXCEPT BOTTOM)

INNER GABLE RUNSOVER TOP OF SIDE INNER GABLE

2" +/-

INNER GABLE TO PROTRUDE THROUGH BOTTOM SHEET

1" x 1/2” GROOVE FOR TRIM DUCKBILL

INSTALL Z-FLASHING ONTO SHAKE/SLATE TILE

TRIM CORNER OF INNER GABLE AS REQUIRED

FLATTEN DIVERTERS AS REQUIRED PRIOR TO APPLYING 2 ROWS OF BUTYL CAULKING

BUILDING PRODUCTS



STEP 1

STEP 2

1" x 1/2” GROOVE FOR TRIM DUCKBILL

CHIMNEY TRIMS INSTALLATION



Page 36 of 39

TYPICAL MASONRY CHIMNEY

SHAKE OR SLATE ROOF SHINGLEBENEATH FLASHINGS CONTINUOS BUTYL SEALANT

APPLIED TO TRIM SURFACE

BUTYL SEALANT BOTH SIDES OF FLAP (TYP.)

GENEROUS AMOUNT OF BUTYL SEALANT

BUTYL SEALANT BOTH SIDES OF FLAP (TYP.)

TYPICAL MASONRY CHIMNEY

SHAKE OR SLATE ROOF SHINGLEBENEATH FLASHINGS

FLASHING FLAPS FOLDED TOGETHER

CONTINUOS BUTYL SEALANT APPLIED IN MASONRY GROOVE AROUND ENTIRE CHIMNEY

END WALL MASONRY

SIDE WALL MASONRY

HIGH END CHIMNEY

SIDE WALL MASONRYEND WALL MASONRY

HIGH END CHIMNEY

BUILDING PRODUCTS



STEP 3

STEP 4

CHIMNEY TRIMS INSTALLATION



Page 37 of 39

1

2

BUILDING PRODUCTS


Shake / Slate SeriesCHIMNEY TRIMS AT HIGH END

1

2

3

CHIMNEY TRIMS AT SIDEWALL

FOLD

CUT

FOLD

CUT

FOLDFOLD

CUT

CHIMNEY TRIMS CUTTING/BENDING

BUILDING PRODUCTS



CHIMNEY BOTTOM

1

2

CUT

FOLD

1

2

BUILDING PRODUCTS



1

2

3


FOLD

CUT

FOLD

CUT

FOLDFOLD

CUT

CHIMNEY TRIMS ON HIGH END

CHIMNEY TRIMS AT SIDE WALL CHIMNEY TRIMS AT BOTTOM

1

2

BUILDING PRODUCTS



1

2

3


FOLD

CUT

FOLD

CUT

FOLDFOLD

CUT



Page 38 of 39

ROOF SLOPE

TOP TRIM

BOTTOM TRIM

4" MIN

BUILDING PRODUCTS


Shake / Slate SeriesENDWALL/SIDE WALL TRIM

ROOF SLOPE

4" MIN

SIDE WALL TRIM

END WALL TRIM

SIDE / END WALL OVERLAP



Page 39 of 39

TOP TRIM

BOTTOM TRIM

BUTYL CAULKING/TAPE CONTINUOUS ACROSS LAP

ROOF SLOPE

2" MIN


BUILDING PRODUCTS



REGLET TRIM

REGLET TRIM

As of June 2020 V1

cedar creek™ shake and north ridge™ slate true nature · cedar creek shake and north ridge...

Documents