ccnp_route_v6_eigrp
DESCRIPTION
ccnp3 route v6TRANSCRIPT
![Page 1: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/1.jpg)
© 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
ROUTE v6 Chapter 2 1
Chapter 2: Configuring the Enhanced Interior Gateway Routing Protocol
CCNP ROUTE: Implementing IP Routing
![Page 2: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/2.jpg)
Chapter 2 2 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Chapter 2 Objectives
Describir la operación básica de EIGRP.
Planificar e implementar el enrutamiento EIGRP.
Configurar y verificar el enrutamiento EIGRP.
Configurar y verificar EIGRP básico en una empresa WAN.
Configurar y verificar EIGRP autenticación.
Describir y configurar mecanismos de optimización EIGRP;
verificar y solucionar problemas de la aplicación general.
![Page 3: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/3.jpg)
Chapter 2 3 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Comprender la Terminología y Operación de EIGRP.
![Page 4: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/4.jpg)
Chapter 2 4 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Capabilities and Attributes
EIGRP es un protocolo de vector-distancia propietario de
Cisco con características de estado de enlace.
Características de EIGRP:
• Convergencia rápida.
• Actualizaciones parciales.
• Soporte para múltiples capas de red.
• El uso de la comunicación multicast y unicast.
• Soporta VLSM
• Conectividad sin fisuras en todos los protocolos y topologías de la
capa de enlace de datos.
• De forma predeterminada, se realiza el resumen de ruta automático
en las principales fronteras de la red (se puede desactivar), pero
también se puede configurar para resumir en las interfaces..
![Page 5: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/5.jpg)
Chapter 2 5 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Terminology
Neighbor table (Tabla de Vecindad)
Topology table (Tabla Topologica)
Routing table (Tabla de Enrutamiento)
Advertised Distance (AD) (Distancia Anunciada)
Feasible Distance (FD) (Distancia Factible)
Successor (Sucesor)
Feasible successor (FS) (Sucesor Factible)
Passive Versus Active Routes
![Page 6: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/6.jpg)
Chapter 2 6 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Tables
Neighbor table
• Contiene las direcciones de los vecinos EIGRP y la interfaz a través
del cual se puede llegar.
Topology table
• Contiene todos los destinos anunciados por los routers vecinos.
Routing table
• Contiene las rutas del sucesor EIGRP.
![Page 7: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/7.jpg)
Chapter 2 7 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Example: EIGRP Tables
Router C’s tables:
![Page 8: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/8.jpg)
Chapter 2 8 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
AD versus FD
Advertised Distance (AD)
• Distancia Anunciada (AD), también conocida como la distancia
notificada, es el costo entre el router del siguiente salto y el destino.
Feasible Distance (FD)
• Distancia factible (FD) es el costo entre el router local y el router del
siguiente salto más AD del router del siguiente salto a la red de
destino.
![Page 9: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/9.jpg)
Chapter 2 9 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Successor and Feasible Successor
Successor • Un sucesor es un router vecino que tiene una ruta de menor coste a un
destino (el más bajo FD) que está garantizado para no ser parte de un bucle de enrutamiento.
• Las rutas del sucesor se ofrecen a la tabla de enrutamiento que se utilizará para reenviar paquetes.
• Pueden existir múltiples sucesores si tienen la misma FD.
Feasible successor (FS) • Un sucesor factible es un vecino que está más cerca de su destino, pero
no es el camino de menor costo.
• Un sucesor factible garantiza una topología libre de bucles, ya que debe tener un AD menor que la FD de la ruta del sucesor actual.
• Sucesores factibles se seleccionan al mismo tiempo, como sucesores, pero se mantienen en la tabla de topología como copias de seguridad a las rutas del suceso
• La tabla de topología puede mantener múltiples sucesores factibles para un destino.
![Page 10: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/10.jpg)
Chapter 2 10 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Passive versus Active Routes
Passive Route
• Una ruta es considerada pasiva cuando el router no funciona
recálculo en esa ruta.
• Pasivo es el estado de funcionamiento, estable.
Active route
• Una ruta está activa cuando está pasando por recálculo.
![Page 11: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/11.jpg)
Chapter 2 11 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Key EIGRP Technologies
Reliable Transport Protocol (RTP)
• Responsable de garantía, entrega ordenada de paquetes EIGRP a todos los vecinos.
Neighbor discovery/recovery mechanism
• Permite a los routers EIGRP aprender dinámicamente cuando sus vecinos se vuelven inalcanzables o inoperante enviando periódicamente pequeños paquetes hello.
Protocol-dependent modules (PDMs)
• Responsable de los requisitos específicos del protocolo de capa de red, como IP, IPv6, AppleTalk y Novell NetWare.
DUAL finite-state machine
• Diffusing Update Algorithm (DUAL) Es el algoritmo de encaminamiento que rastrea todas las rutas anunciadas por todos los vecinos y utiliza la información de distancia, conocida como la métrica compuesta, para seleccionar, rutas sin bucles eficientes para todos los destinos.
![Page 12: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/12.jpg)
Chapter 2 12 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Reliable Transport Protocol
EIGRP no puede utilizar los servicios de UDP o TCP desde
IPX y Appletalk no utilizan el / conjunto de protocolos TCP
IP.
Protocolo de transporte confiable (RTP) es el protocolo de
capa de transporte utilizado únicamente por EIGRP para la
entrega y recepción de paquetes EIGRP.
• RTP es similar a TCP pero es un propietario de Cisco.
RTP ofrece servicio confiable o no confiable como la
situación lo amerita.
• Paquetes fiables (actualización, consulta, respuesta) requieren el
reconocimiento explícito mientras que los paquetes no confiables
(Hello, ACK) no lo hacen.
![Page 13: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/13.jpg)
Chapter 2 13 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Neighbor Discovery / Recovery
Los routers EIGRP establecen activamente relaciones con
sus vecinos.
Las adyacencias se establecen utilizando pequeños
paquetes Hello que se envían cada 5 ó 60 segundos.
• Si un vecino pierde 3 paquetes hello consecutivos luego la ruta se
considera no válida.
• Default = 15 seconds or 180 seconds.
![Page 14: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/14.jpg)
Chapter 2 14 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Neighbor Discovery / Recovery
![Page 15: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/15.jpg)
Chapter 2 15 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Protocol-Dependent Modules
Diversos protocolos enrutados son apoyados a través de
sus PDMs.
• Proporciona independencia de los protocolos enrutados.
• Los PDM son modulares, escalables y adaptables.
• EIGRP puede adaptarse a los protocolos enrutados nuevos o
revisados.
• PDM protegen EIGRP de la revisión minuciosa.
Cada PDM es responsable de todas las funciones
relacionadas con su protocolo de enrutado específico.
![Page 16: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/16.jpg)
Chapter 2 16 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Protocol-Dependent Modules
EIGRP mantiene las tablas individuales para cada protocolo enrutado.
![Page 17: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/17.jpg)
Chapter 2 17 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
DUAL finite-state machine
DUAL usa las tablas de vecinos y de topología para
calcular la información de ruta.
Cuando falla un enlace, DUAL busca un sucesor factible en
sus tablas de vecinos y Topología.
• Compara todas las rutas publicadas por los vecinos mediante el uso
de una métrica compuesta para cada ruta.
• Caminos de menor costo se insertan en la tabla de enrutamiento.
![Page 18: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/18.jpg)
Chapter 2 18 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Packet
Frame Header
Frame Payload
CRC IP
Header Protocol Number
(EIGRP = 88)
EIGRP
Header
EIGRP
Message
En una LAN, el paquete
EIGRP se encapsula en
una trama Ethernet con
una dirección MAC
multicast de destino:
01-00-5E-00-00-0A
La dirección IP de destino se
establece en el multicast
224.0.0.10 y el campo de
protocolo EIGRP es 88.
El encabezado
EIGRP identifica
el tipo de paquete
EIGRP y número
de sistema
autónomo.
El mensaje
EIGRP
consiste en el
Tipo /
Longitud /
Valor (TLV).
![Page 19: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/19.jpg)
Chapter 2 19 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Header
EIGRP utiliza estos 5 tipos de paquetes para mantener sus
diversas tablas y establecer relaciones complejas con los
routers vecinos:
• Hello
• Acknowledgment
• Update
• Query
• Reply
![Page 20: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/20.jpg)
Chapter 2 20 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Header
![Page 21: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/21.jpg)
Chapter 2 21 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Packet
![Page 22: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/22.jpg)
Chapter 2 22 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Hello Packets
EIGRP depende de paquetes Hello para descubrir, verificar
y redescubrir los routers vecinos.
Paquetes de saludo EIGRP son multicast 224.0.0.10.
Paquetes Hello se envían siempre poco fiable y por lo tanto
no requieren acuse de recibo.
![Page 23: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/23.jpg)
Chapter 2 23 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Hello Packets
![Page 24: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/24.jpg)
Chapter 2 24 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Hello Packets
Hellos se envían a intervalos fijos (y configurable), llamado
“Hello interval”.
• Temporizadores Hello/Hold no tienen que coincidir.
• Para restablecer el intervalo de saludo: no ip hello-interval eigrp as#
Hello interval depende del ancho de banda de la interfaz.
• Alto ancho de banda = 5 seconds
• Intervalo predeterminado en punto a punto de enlaces seriales, circuitos
multipunto con un ancho de banda superior a T1, y LANs.
• Bajo ancho de banda = 60 seconds
• Intervalo predeterminado en T1 o inferior multipunto circuitos WAN.
![Page 25: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/25.jpg)
Chapter 2 25 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Hello Packets
Al escuchar Hellos, un router crea una tabla de vecinos y la
recepción continua de Hellos mantiene la tabla.
Holdtime es la cantidad máxima de tiempo permitido que
los Hello no se escuchan de un vecino.
• Three times the Hello Interval:
• Low Bandwidth (3 x 60 sec.) = 180 seconds
• High bandwidth (3 x 5 sec.) = 15 seconds
![Page 26: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/26.jpg)
Chapter 2 26 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Hello Packets
T3
![Page 27: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/27.jpg)
Chapter 2 27 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Acknowledgement Packets
Se utilizan para indicar la recepción de cualquier paquete
EIGRP durante un Intercambio "fiable“, (es decir, RTP)
Para ser fiable, el mensaje de un remitente debe ser
reconocido por el receptor.
Acknowledgment packets are:
• Paquetes sin datos de Hello.
• Unicast.
![Page 28: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/28.jpg)
Chapter 2 28 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Update Packets
Después de que el router local descubre un nuevo vecino,
los paquetes de actualización (update) se envían al nuevo
vecino.
Los paquetes de actualización (update) también se utilizan
cuando un router detecta un cambio en la topología.
• El router envía una actualización de paquetes multicast a todos los
vecinos, alertando al cambio.
Todos los paquetes de actualización se envían de forma
fiable.
![Page 29: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/29.jpg)
Chapter 2 29 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Update Packets
Update packet • Initially sent after a new neighbor is discovered. • Sent when a topology change has been detected.
![Page 30: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/30.jpg)
Chapter 2 30 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Query and Reply Packets
Los paquetes de consulta y la respuesta (Query and Reply)
se envía cuando un destino no tiene sucesores factibles.
Ambos tipos de paquetes se envían de forma fiable.
Un paquete de consulta se de multidifusión a otros routers
EIGRP durante el proceso de recálculo de ruta.
• Los paquetes de consulta (query) siempre son multicast.
Un paquete de respuesta (reply) se utiliza para responder a
una consulta para instruir el autor no para volver a calcular
la ruta porque existen sucesores factibles.
• Responder paquetes son siempre unicast.
![Page 31: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/31.jpg)
Chapter 2 31 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Query and Reply Packets
![Page 32: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/32.jpg)
Chapter 2 32 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Message
![Page 33: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/33.jpg)
Chapter 2 33 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Message - TLVs
![Page 34: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/34.jpg)
Chapter 2 34 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
TLV 0x0001 - EIGRP Parameters
• Valores de K se utilizan para calcular la métrica de EIGRP.
• El Hold Time se anunciaba con un vecino es el tiempo máximo
que un router debe esperar para cualquier mensaje EIGRP válido
enviada por ese vecino antes de declararla muerta.
![Page 35: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/35.jpg)
Chapter 2 35 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
TLV 0x0002 - Internal IP Routes
• Delay: Suma de los retrasos en
unidades de 10 microsegundos
desde el origen al destino.
• Bandwidth: Ancho de banda
más bajo configurado en
cualquier interfaz a lo largo de la
ruta.
• Prefix length: Especifica el
número de bits de red en la
máscara de subred.
• Destination: La dirección de
destino de la ruta.
![Page 36: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/36.jpg)
Chapter 2 36 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
TLV 0x0003 - External IP Routes
Rutas externas IP son rutas que se importan en EIGRP mediante la redistribución de una ruta por defecto u otros protocolos de enrutamiento.
• Los campos que se utilizan para
realizar un seguimiento de fuente
externa de ruta.
• Los mismos campos contenidos
en la ruta TLV IP interna (0x0002)
![Page 37: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/37.jpg)
Chapter 2 37 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Packet Types
Packet Type Use
Hello Se utiliza para descubrir otros routers EIGRP
en la red.
Acknowledgement Se utiliza para acusar recibo de cualquier
paquete EIGRP.
Update Transmitir información de rutas a destinos
conocidos.
Query Se utiliza para obtener información específica
de un router vecino.
Reply Se utiliza para responder a un query (consulta).
![Page 38: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/38.jpg)
Chapter 2 38 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Initial Route Discovery
![Page 39: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/39.jpg)
Chapter 2 39 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Operations
EIGRP selecciona rutas primaria (sucesor) y de respaldo (sucesor
factible) e inyecta aquellos en la tabla de topología.
Las rutas primarias (sucesores) se mueven a la tabla de enrutamiento.
IP EIGRP Neighbor Table
Neighbor IP Address Local router exit
interface to neighbor
IP EIGRP Topology Table
Destination 1 FD / AD via each neighbor
IP Routing Table
Destination 1 Best route
Lista de los routers vecinos EIGRP adyacentes conectados directamente y la interfaz local para salir para llegar a él.
Listado de todas las rutas aprendidas de cada vecino EIGRP e identifica rutas del sucesor y las rutas del sucesor factibles.
Lista de las mejores rutas (sucesores) de la tabla de topología EIGRP y otros procesos de enrutamiento.
![Page 40: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/40.jpg)
Chapter 2 40 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Example: EIGRP Tables
Router C’s tables:
![Page 41: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/41.jpg)
Chapter 2 41 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
R1# show ip eigrp neighbors
IP-EIGRP neighbors for process 100
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
0 192.168.1.102 Se0/0/1 11 00:07:22 10 2280 0 5
R1#
EIGRP Neighbor Table
Enumera el orden en el que una sesión de peering se estableció con el vecino especificado, empezando por 0.
Dirección IP del vecino
Interfaz local la recepción de paquetes hello EIGRP.
Segundos restantes antes de declarar vecino abajo. El tiempo de espera actual y se restablece en el tiempo máximo de espera cuando se recibe un paquete de saludo.
SRTT (Smooth Round Trip Timer) and RTO (Retransmit Interval) son utilizados por RTP para administrar paquetes EIGRP confiables.
SRTT indica el tiempo que le toma a este vecino de responder a los paquetes confiables.
RTO indica cuánto tiempo debe esperar antes de retransmitir si no se recibe ACK
Queue count should always be zero otherwise there’s congestion on the link.
El número de secuencia del último paquete de actualización, consulta o respuesta que se recibió desde este vecino.
Cantidad de tiempo que desde este vecino se agregó a la tabla de vecinos.
![Page 42: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/42.jpg)
Chapter 2 42 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
R1# show ip eigrp topology
IP-EIGRP Topology Table for AS(100)/ID(192.168.1.101)
Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply,
r - reply Status, s - sia Status
P 172.17.0.0/16, 1 successors, FD is 40514560
via 192.168.1.102 (40514560/28160), Serial0/0/1
R1#
EIGRP Topology Table
Indica si la ruta se encuentra en estado pasivo o activo.
Red de destino. Número de sucesores
Dirección del
siguiente salto
para el sucesor.
Interfaz de salida para alcanzar la red.
Distancia factible (FD) al destino
Distancia factible (FD) al destino
Distancia Anunciado (AD) del sucesor
![Page 43: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/43.jpg)
Chapter 2 43 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Routing Table
EIGRP route
Red de destino
R1# show ip route
<output omitted>
Gateway of last resort is not set
D 172.17.0.0/16 [90/40514560] via 192.168.1.102, 00:02:22, Serial0/0/1
172.16.0.0/16 is variably subnetted, 2 subnets, 2 masks
D 172.16.0.0/16 is a summary, 00:31:31, Null0
C 172.16.1.0/24 is directly connected, FastEthernet0/0
R1#
La distancia administrativa
Distancia factible
Dirección del siguiente salto para alcanzar la red
Tiempo que indica el último paquete de actualización recibida
Interface de Router local de salida para alcanzar la red de destino
Resumen de Ruta que se crea automáticamente como resultado de la conducta con clase por defecto de EIGRP.
![Page 44: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/44.jpg)
Chapter 2 44 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Administrative Distance (AD)
Distancias Administrativas por defecto de EIGRP
Routes manually
summarized.
Routes redistributed into
EIGRP.
![Page 45: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/45.jpg)
Chapter 2 45 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
DUAL Example
(1)
10.1.1.0 /24
A
C
B
E
D
(2) (2) (1)
(1)
(1)
EIGRP FD AD Topology
10.1.1.0 /24 3 ***** Passive *****
via B 3 1 Successor
via D 4 2 Feasible Successor
via E 4 3
Router C
EIGRP FD AD Topology
10.1.1.0 /24 3 ***** Passive *****
via D 3 2 Successor
via C 4 3
Router E
EIGRP FD AD Topology
10.1.1.0 /24 2 ***** Passive *****
via B 2 1 Successor
via C 5 3
Router D
![Page 46: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/46.jpg)
Chapter 2 46 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
DUAL Example
(1)
10.1.1.0 /24
A
C
B
E
D
(2) (2) (1)
(1)
(1)
EIGRP FD AD Topology
10.1.1.0 /24 3 ***** Passive *****
via B 3 1 Successor
via D 4 2 Feasible Successor
via E 4 3
Router C
EIGRP FD AD Topology
10.1.1.0 /24 3 ***** Passive *****
via D 3 2 Successor
via C 4 3
Router E
EIGRP FD AD Topology
10.1.1.0 /24 2 ***** Passive *****
via B 2 1 Successor
via C 5 3
Router D
![Page 47: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/47.jpg)
Chapter 2 47 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
DUAL Example
(1)
10.1.1.0 /24
A
C
B
E
D
(2) (2) (1)
(1)
EIGRP FD AD Topology
10.1.1.0 /24 3 ***** Passive *****
via B 3 1 Successor
via D 4 2 Feasible Successor
via E 4 3
Router C
EIGRP FD AD Topology
10.1.1.0 /24 3 ***** Passive *****
via D 3 2 Successor
via C 4 3
Router E
EIGRP FD AD Topology
10.1.1.0 /24 -1 ***** ACTIVE ******
via E (Q) Query
via C 5 3 (Q) Query
Router D
Q Q Q = Query
![Page 48: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/48.jpg)
Chapter 2 48 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
DUAL Example
(1)
10.1.1.0 /24
A
C
B
E
D
(2) (2) (1)
(1)
EIGRP FD AD Topology
10.1.1.0 /24 3 ***** Passive *****
via B 3 1 Successor
via D
via E 4 3
Router C
EIGRP FD AD Topology
10.1.1.0 /24 -1 ***** ACTIVE ******
via D
via C 4 3 (Q) Query
Router E
EIGRP FD AD Topology
10.1.1.0 /24 -1 ***** ACTIVE ******
via E (Q) Query
via C 5 3
Router D
R
Q
Q = Query
R = Reply
![Page 49: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/49.jpg)
Chapter 2 49 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
DUAL Example
(1)
10.1.1.0 /24
A
C
B
E
D
(2) (2) (1)
(1)
EIGRP FD AD Topology
10.1.1.0 /24 3 ***** Passive *****
via B 3 1 Successor
via D
via E
Router C
EIGRP FD AD Topology
10.1.1.0 /24 4 ***** Passive *****
via C 4 3 Successor
via D
Router E
EIGRP FD AD Topology
10.1.1.0 /24 -1 ***** ACTIVE ******
via E (Q) Query
via C 5 3
Router D
R
Q = Query
R = Reply
![Page 50: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/50.jpg)
Chapter 2 50 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
DUAL Example
(1)
10.1.1.0 /24
A
C
B
E
D
(2) (2) (1)
(1)
EIGRP FD AD Topology
10.1.1.0 /24 3 ***** Passive *****
via B 3 1 Successor
via D
via E
Router C
EIGRP FD AD Topology
10.1.1.0 /24 4 ***** Passive *****
via C 4 3 Successor
via D
Router E
EIGRP FD AD Topology
10.1.1.0 /24 5 ***** Passive *****
via C 5 3 Successor
via E 5 4 Successor
Router D
R
Q = Query
R = Reply
![Page 51: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/51.jpg)
Chapter 2 51 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
DUAL Example
(1)
10.1.1.0 /24
A
C
B
E
D
(2) (2) (1)
(1)
EIGRP FD AD Topology
10.1.1.0 /24 3 ***** Passive *****
via B 3 1 Successor
via D
via E
Router C
EIGRP FD AD Topology
10.1.1.0 /24 4 ***** Passive *****
via C 4 3 Successor
via D
Router E
EIGRP FD AD Topology
10.1.1.0 /24 5 ***** Passive *****
via C 5 3 Successor
via E 5 4 Successor
Router D
![Page 52: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/52.jpg)
Chapter 2 52 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Metric Calculation
EIGRP utiliza una métrica compuesta que puede basarse
en las siguientes métricas :
• Bandwidth
• Delay
• Reliability
• Load
Sólo de ancho de banda y el retardo (delay) se utilizan de
forma predeterminada.
Note: A menudo se afirma incorrectamente que EIGRP también puede
utilizar el MTU más pequeño en el camino. En realidad, la MTU se incluye
en la actualización de enrutamiento EIGRP, pero no se utiliza realmente
en el cálculo de la métrica.
![Page 53: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/53.jpg)
Chapter 2 53 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Bandwidth
EIGRP utiliza el ancho de banda más lento (BW) en su
cálculo de la métrica.
• BW Calculado = BW Referencia / BW más lento (kbps)
El valor del ancho de banda puede o puede no reflejar el
ancho de banda físico real de la interfaz.
• Por ejemplo, la mayoría de las interfaces seriales utilizan el valor de
ancho de banda por defecto de 1.544 Mbps, pero esto puede no
reflejar con precisión los vínculos ancho de banda real.
![Page 54: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/54.jpg)
Chapter 2 54 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Bandwidth
Debido a que tanto el ancho de banda de EIGRP y OSPF
es el uso de calculo por defecto de la métrica, un valor
correcto para el ancho de banda es muy importante para la
exactitud de la información de enrutamiento.
• Si el ancho de banda real del enlace difiere del valor de ancho de
banda predeterminado, entonces el valor de ancho de banda debe
ser modificado.
Para modificar el valor del ancho de banda, utilice el
comando en la interfaz “bandwidth”.
Note: El comando bandwidth no cambia el ancho de banda físico del
enlace.
![Page 55: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/55.jpg)
Chapter 2 55 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Delay
El retardo (delay) es una medida del tiempo que tarda un paquete que atraviese una ruta.
• EIGRP utiliza la suma acumulada de todos los interfaces de salida.
• Calculado Delay = la suma de los retardos de salida de interfaz / 10.
El delay (DLY) es un valor estático de la métrica basado en el tipo de enlace a la que la interfaz se conecta y se expresa en microsegundos.
![Page 56: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/56.jpg)
Chapter 2 56 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Other EIGRP Metrics
Confiabilidad (Reliability, no es una métrica de EIGRP por
defecto) es una medida de la probabilidad de que un enlace
fallará.
• Medir dinámicamente y expresado como una fracción de 255.
Cuanto mayor sea la fracción de la mejor será la fiabilidad.
Load (no es una métrica de EIGRP por defecto) refleja la
cantidad de tráfico que se utiliza un enlace.
• El número está determinado dinámicamente y se expresa como una
fracción de 255
Cuanto menor es la fracción menor es la carga en el enlace.
Estos criterios opcionales se pueden usar, pero no se
recomienda, ya que suelen dar lugar a un nuevo cálculo
frecuente de la tabla de topología.
![Page 57: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/57.jpg)
Chapter 2 57 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Composite Metric Calculation
La fórmula métrica compuesta de EIGRP se compone de valores de K1 a K5, conocida como EIGRP pesos métricos.
• By default, only K1 (bandwidth) and K3 (delay) are set to 1.
• K2 (load), K4 (reliability), and K5 (MTU) are set to 0.
Valores de K se pueden cambiar con el comando router EIGRP:
Router(config-router)# metric weights tos k1 k2 k3
k4 k5
![Page 58: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/58.jpg)
Chapter 2 58 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Mismatched K Values
Vecinos EIGRP no pueden utilizar valores de métrica
desiguales.
• Todos los vecinos EIGRP deben utilizar la misma métrica.
• Las métricas se pueden modificar con el comando metric weights
![Page 59: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/59.jpg)
Chapter 2 59 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Metric Calculation Example
Ancho de banda más lento :
Además, la suma de los retrasos
![Page 60: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/60.jpg)
Chapter 2 60 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Bandwidth Calculation Example
Bandwidth = 10,000,000 / 1024 = 9765 * 256 = 2499840
![Page 61: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/61.jpg)
Chapter 2 61 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Delay Calculation Example
Delay = 20,000 / 10 + (100 / 10) * 256 = 514560
![Page 62: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/62.jpg)
Chapter 2 62 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Metric Calculation Example
EIGRP Metric = 2499840 + 514560 = 3014400
![Page 63: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/63.jpg)
Chapter 2 63 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Planning EIGRP Routing Implementations
![Page 64: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/64.jpg)
Chapter 2 64 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Planning to Deploy EIGRP
Antes de la implementación de una solución de
enrutamiento EIGRP, lo siguiente debe ser considerado :
• Plan de direccionamiento IP.
• Topología de red.
• Ingeniería de tráfico EIGRP.
Una vez que se han evaluado las necesidades, el plan de
aplicación se puede crear.
![Page 65: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/65.jpg)
Chapter 2 65 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Implementing EIGRP
La información necesaria para implementar el enrutamiento
EIGRP incluye la siguiente:
• Las direcciones IP para ser configurado en las interfaces de un router
individual.
• El número AS EIGRP, utilizado para permitir EIGRP.
Una lista de los routers e interfaces en los que EIGRP se debe
activar.
• Métricas de que necesitan ser aplicado a interfaces específicas, o la
ingeniería de tráfico EIGRP.
En el plan de implementación, EIGRP las tareas incluyen
las siguientes:
• Habilitar el protocolo de enrutamiento EIGRP.
• Configuración de las sentencias de red apropiados.
• Opcionalmente configurar la métrica con las interfaces adecuadas.
![Page 66: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/66.jpg)
Chapter 2 66 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Verifying EIGRP
Después de implementar EIGRP, la verificación debe
confirmar el despliegue apropiado en cada router.
Tareas de verificación incluyen:
• Las relaciones de vecindad EIGRP.
• Que la tabla de topología EIGRP se rellena con la información
necesaria.
• Esa tabla de enrutamiento IP se rellena con la información necesaria.
Eso no es la conectividad en la red entre los routers y a otros
dispositivos.
• Que EIGRP se comporta como se esperaba en un caso de un cambio
de topología, por fallo de enlace de las pruebas y el router eventos de
fallo.
![Page 67: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/67.jpg)
Chapter 2 67 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Documenting
Después de un despliegue satisfactorio EIGRP, el proceso
y los resultados de la solución y la verificación deben ser
documentados para futuras consultas.
La documentación debe incluir :
• Un mapa de topología.
• El plan de direccionamiento IP.
• El número utilización AS.
• Las redes incluyen en EIGRP en cada router.
• Cualquier métricas especiales configuradas.
![Page 68: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/68.jpg)
Chapter 2 68 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Configuring and Verifying EIGRP
![Page 69: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/69.jpg)
Chapter 2 69 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Activar enrutamiento EIGRP.
Definir EIGRP como el protocolo de enrutamiento IP.
Router(config)#
router eigrp autonomous-system-id
Para intercambiar actualizaciones de enrutamiento, los routers EIGRP deben tener el mismo ID de sistema autónomo.
![Page 70: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/70.jpg)
Chapter 2 70 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Identificar EIGRP Redes.
Definir las redes EIGRP para anunciar a los vecinos EIGRP.
Router(config-router)#
network network [mask]
El parámetro network puede ser una red, una subred, o la dirección de un interfaz conectada directamente.
La máscara es una wildcard mask (máscara inversa) que se utiliza para determinar la forma de interpretar la dirección.
• La máscara tiene bits wildcard, donde 0 es una coincidencia y 1 "no importa.“
• Por ejemplo, 0.0.255.255 indica un partido en los primeros 2 octetos.
![Page 71: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/71.jpg)
Chapter 2 71 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Note on EIGRP Masks
La mayoría de las referencias EIGRP establecen que se
requiere la máscara wildcard.
Sin embargo, desde IOS 12.0 (4) T, el argumento de
máscara en realidad puede ser configurado utilizando bits
wildcard o una máscara de subred regular.
Por ejemplo, ya sea en formato podría ser utilizado para
configurar la red 10.10.10.0:
network 10.10.10.0 0.0.0.3
or
network 10.10.10.0 255.255.255.252
![Page 72: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/72.jpg)
Chapter 2 72 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Define the Interface Bandwidth
Define el ancho de banda de la interfaz (opcional).
Router(config-if)#
bandwidth kilobits
El parámetro kilobits indica el ancho de banda destinado en kbps.
Por ejemplo, para establecer el ancho de banda a 512 000 bps, utilice el comando bandwidth 512.
El ancho de banda configurado es utilizado por los protocolos de enrutamiento en el cálculo de la métrica.
El comando no cambia realmente la velocidad de la interfaz.
![Page 73: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/73.jpg)
Chapter 2 73 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Enable / Disable Automatic Summarization
De forma predeterminada, EIGRP resume automáticamente
las subredes.
Router(config-router)#
auto-summary
Esto hace que EIGRP se comporte como un protocolo de enrutamiento con clase y por lo tanto se resumen las subredes en el límite con clase.
Resumen automático se puede desactivar con el comando de configuración del router no auto-summary.
![Page 74: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/74.jpg)
Chapter 2 74 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Configuring EIGRP Example: Classful
R1(config)# interface Fa0/0
R1(config-if)# ip address 172.16.1.1 255.255.255.0
R1(config-if)# no shut
R1(config-if)# interface S0/0/0
R1(config-if)# ip address 192.168.1.101 255.255.255.224
R1(config-if)# bandwidth 64
R1(config-if)# no shut
R1(config-if)# exit
Classful configuration example:
R2(config)# interface Fa0/0
R2(config-if)# ip address 172.16.2.1 255.255.255.0
R2(config-if)# no shut
R2(config-if)# interface S0/0/0
R2(config-if)# ip address 192.168.1.102 255.255.255.224
R2(config-if)# bandwidth 64
R2(config-if)# no shut
R2(config-if)# interface S0/0/1
R2(config-if)# ip address 192.168.1.1 255.255.255.224
R2(config-if)# bandwidth 64
R2(config-if)# no shut
R2(config-if)# exit
Fa0/0 Fa0/0
R1 R2
172.16.1.0 /24
EIGRP AS 100
Internet
192.168.1.0 /27
S0/0/1
172.17.2.0 /24
S0/0/0 S0/0/0
64 kbps 192.168.1.96 /27
.101
.102 .1
.1 .1
![Page 75: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/75.jpg)
Chapter 2 75 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Configuring EIGRP Example: Classful
R1(config)# router eigrp 100
R1(config-router)# network 192.168.1.96
R1(config-router)# network 172.16.1.0
R1(config-router)#
Classful configuration example:
R2(config)# router eigrp 100
R2(config-router)# network 192.168.1.96
R2(config-router)# network 172.17.2.0
*Jul 26 10:02:25.963: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 192.168.1.101 (Serial0/0/0) is
up: new adjacency 172.17.2.0
R2(config-router)#
R2#
Fa0/0 Fa0/0
R1 R2
172.16.1.0 /24
EIGRP AS 100
Internet
192.168.1.0 /27
S0/0/1
172.17.2.0 /24
S0/0/0 S0/0/0
64 kbps 192.168.1.96 /27
.101
.102 .1
.1 .1
![Page 76: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/76.jpg)
Chapter 2 76 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Verifying EIGRP Example
R1# show running-config | section router eigrp
router eigrp 100
network 172.16.0.0
network 192.168.1.0
auto-summary
R1# show ip route
<output omitted>
Gateway of last resort is not set
D 172.17.0.0/16 [90/40514560] via 192.168.1.102, 00:24:02, Serial0/0/0
172.16.0.0/16 is variably subnetted, 2 subnets, 2 masks
D 172.16.0.0/16 is a summary, 00:25:27, Null0
C 172.16.1.0/24 is directly connected, FastEthernet0/0
192.168.1.0/24 is variably subnetted, 3 subnets, 2 masks
C 192.168.1.96/27 is directly connected, Serial0/0/0
D 192.168.1.0/27 [90/41024000] via 192.168.1.102, 00:16:56, Serial0/0/0
D 192.168.1.0/24 is a summary, 00:25:27, Null0
R1#
Classful configuration example:
Fa0/0 Fa0/0
R1 R2
172.16.1.0 /24
EIGRP AS 100
Internet
192.168.1.0 /27
S0/0/1
172.17.2.0 /24
S0/0/0 S0/0/0
64 kbps 192.168.1.96 /27
.101
.102 .1
.1 .1
![Page 77: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/77.jpg)
Chapter 2 77 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Verifying EIGRP Example
R2# show running-config | section router eigrp
router eigrp 100
network 172.17.0.0
network 192.168.1.0
auto-summary
R2# show ip route
<output omitted>
Gateway of last resort is not set
172.17.0.0/16 is variably subnetted, 2 subnets, 2 masks
D 172.17.0.0/16 is a summary, 00:13:10, Null0
C 172.17.2.0/24 is directly connected, FastEthernet0/0
D 172.16.0.0/16 [90/40514560] via 192.168.1.101, 00:13:26, Serial0/0/0
192.168.1.0/24 is variably subnetted, 3 subnets, 2 masks
C 192.168.1.96/27 is directly connected, Serial0/0/0
C 192.168.1.0/27 is directly connected, Serial0/0/1
D 192.168.1.0/24 is a summary, 00:13:10, Null0
R2#
Classful configuration example:
Fa0/0 Fa0/0
R1 R2
172.16.1.0 /24
EIGRP AS 100
Internet
192.168.1.0 /27
S0/0/1
172.17.2.0 /24
S0/0/0 S0/0/0
64 kbps 192.168.1.96 /27
.101
.102 .1
.1 .1
![Page 78: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/78.jpg)
Chapter 2 78 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Verifying EIGRP Example
R2# show ip protocols
Routing Protocol is "eigrp 100"
<output omitted>
Automatic network summarization is in effect
Automatic address summarization:
192.168.1.0/24 for FastEthernet0/0
Summarizing with metric 40512000
172.17.0.0/16 for Serial0/0/0, Serial0/0/1
Summarizing with metric 28160
Maximum path: 4
Routing for Networks:
172.17.0.0
192.168.1.0
Routing Information Sources:
<output omitted>
R2#
Ejemplo de configuración con clase :
Fa0/0 Fa0/0
R1 R2
172.16.1.0 /24
EIGRP AS 100
Internet
192.168.1.0 /27
S0/0/1
172.17.2.0 /24
S0/0/0 S0/0/0
64 kbps 192.168.1.96 /27
.101
.102 .1
.1 .1
![Page 79: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/79.jpg)
Chapter 2 79 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Configuring EIGRP Example: Classless
Ejemplo de configuración sin clase:
R2(config)# no router eigrp 100
R2(config)# router eigrp 100
R2(config-router)# network 192.168.1.96 0.0.0.31
R2(config-router)# network 172.17.2.0 0.0.0.255
R2(config-router)# end
R2# show run | section router eigrp
router eigrp 100
network 172.17.2.0 0.0.0.255
network 192.168.1.96 0.0.0.31
auto-summary
R2#
Fa0/0 Fa0/0
172.17.2.0 /24
R1 R2
172.16.1.0 /24
EIGRP AS 100
Internet
192.168.1.0 /27
64 kbps 192.168.1.96 /27
.101
.102 S0/0/1
S0/0/0 S0/0/0
.1
.1 .1
R1(config)# no router eigrp 100
R1(config)# router eigrp 100
R1(config-router)# network 192.168.1.96 0.0.0.31
R1(config-router)# network 172.16.1.0 0.0.0.255
R1(config-router)# end
R1# show run | section router eigrp
router eigrp 100
network 172.16.1.0 0.0.0.255
network 192.168.1.96 0.0.0.31
auto-summary
R1#
![Page 80: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/80.jpg)
Chapter 2 80 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Verifying EIGRP Example
R2# show ip protocols
Routing Protocol is "eigrp 100"
<output omitted>
Automatic network summarization is in effect
Automatic address summarization:
192.168.1.0/24 for FastEthernet0/0
Summarizing with metric 40512000
172.17.0.0/16 for Serial0/0/0
Summarizing with metric 28160
Maximum path: 4
Routing for Networks:
172.17.2.0/24
192.168.1.96/27
Routing Information Sources:
Gateway Distance Last Update
(this router) 90 00:00:06
Gateway Distance Last Update
192.168.1.101 90 00:00:26
Distance: internal 90 external 170
Ejemplo de configuración con clase :
Fa0/0 Fa0/0
R1 R2
172.16.1.0 /24
EIGRP AS 100
Internet
192.168.1.0 /27
S0/0/1
172.17.2.0 /24
S0/0/0 S0/0/0
64 kbps 192.168.1.96 /27
.101
.102 .1
.1 .1
![Page 81: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/81.jpg)
Chapter 2 81 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Verifying EIGRP: show ip protocols
R1# show ip protocols
Routing Protocol is "eigrp 100"
<output omitted>
EIGRP metric weight K1=1, K2=0, K3=1, K4=0, K5=0
EIGRP maximum hopcount 100
EIGRP maximum metric variance 1
Redistributing: eigrp 100
EIGRP NSF-aware route hold timer is 240s
Automatic network summarization is in effect
Automatic address summarization:
192.168.1.0/24 for FastEthernet0/0
Summarizing with metric 40512000
172.16.0.0/16 for Serial0/0/0
Summarizing with metric 28160
Maximum path: 4
Routing for Networks:
172.16.1.0/24
192.168.1.96/27
Routing Information Sources:
Gateway Distance Last Update
(this router) 90 00:08:56
Gateway Distance Last Update
192.168.1.102 90 00:07:59
Distance: internal 90 external 170
Compruebe la información de protocolo de enrutamiento en el router.
![Page 82: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/82.jpg)
Chapter 2 82 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Verifying EIGRP: show ip eigrp neighbors
R1# show ip eigrp neighbors
IP-EIGRP neighbors for process 100
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
0 192.168.1.102 Se0/0/0 11 00:09:17 22 2280 0 5
R1#
EIGRP uses the Neighbor table to list adjacent routers.
![Page 83: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/83.jpg)
Chapter 2 83 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Verifying EIGRP: show ip eigrp topology
R1# show ip eigrp topology
IP-EIGRP Topology Table for AS(100)/ID(192.168.1.101)
Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply,
r - reply Status, s - sia Status
P 192.168.1.96/27, 1 successors, FD is 40512000
via Connected, Serial0/0/0
P 192.168.1.0/24, 1 successors, FD is 40512000
via Summary (40512000/0), Null0
P 172.16.0.0/16, 1 successors, FD is 28160
via Summary (28160/0), Null0
P 172.17.0.0/16, 1 successors, FD is 40514560
via 192.168.1.102 (40514560/28160), Serial0/0/0
P 172.16.1.0/24, 1 successors, FD is 28160
via Connected, FastEthernet0/0
R1#
Compruebe la información de protocolo de enrutamiento en el router.
![Page 84: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/84.jpg)
Chapter 2 84 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Verifying EIGRP: show ip route eigrp
R1# show ip route eigrp
D 172.17.0.0/16 [90/40514560] via 192.168.1.102, 00:10:18, Serial0/0/0
172.16.0.0/16 is variably subnetted, 2 subnets, 2 masks
D 172.16.0.0/16 is a summary, 00:11:19, Null0
192.168.1.0/24 is variably subnetted, 2 subnets, 2 masks
D 192.168.1.0/24 is a summary, 00:11:19, Null0
R1#
R1# show ip route
<output omitted>
Gateway of last resort is not set
D 172.17.0.0/16 [90/40514560] via 192.168.1.102, 00:10:35, Serial0/0/0
172.16.0.0/16 is variably subnetted, 2 subnets, 2 masks
D 172.16.0.0/16 is a summary, 00:11:37, Null0
C 172.16.1.0/24 is directly connected, FastEthernet0/0
192.168.1.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.1.96/27 is directly connected, Serial0/0/0
D 192.168.1.0/24 is a summary, 00:11:37, Null0
R1#
Compruebe que el router reconoce rutas EIGRP.
![Page 85: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/85.jpg)
Chapter 2 85 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Verifying EIGRP: show ip eigrp interfaces
R1# show ip eigrp interfaces
IP-EIGRP interfaces for process 100
Xmit Queue Mean Pacing Time Multicast Pending
Interface Peers Un/Reliable SRTT Un/Reliable Flow Timer Routes
Se0/0/0 1 0/0 22 10/380 468 0
Fa0/0 0 0/0 0 0/1 0 0
R1#
Verifique las interfaces configuradas con EIGRP.
![Page 86: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/86.jpg)
Chapter 2 86 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Verifying EIGRP: show ip eigrp traffic
R1# show ip eigrp traffic
IP-EIGRP Traffic Statistics for AS 100
Hellos sent/received: 338/166
Updates sent/received: 7/7
Queries sent/received: 0/0
Replies sent/received: 0/0
Acks sent/received: 2/2
SIA-Queries sent/received: 0/0
SIA-Replies sent/received: 0/0
Hello Process ID: 228
PDM Process ID: 226
IP Socket queue: 0/2000/1/0 (current/max/highest/drops)
Eigrp input queue: 0/2000/1/0 (current/max/highest/drops)
R1#
Verifique la información de tráfico de EIGRP.
![Page 87: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/87.jpg)
Chapter 2 87 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Verifying EIGRP: debug eigrp packets
R2# debug eigrp packets
*Jul 26 10:51:24.051: EIGRP: Sending HELLO on Serial0/0/0
*Jul 26 10:51:24.051: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0
*Jul 26 10:51:24.111: EIGRP: Sending HELLO on FastEthernet0/0
*Jul 26 10:51:24.111: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0
*Jul 26 10:51:26.667: EIGRP: Received HELLO on Serial0/0/0 nbr 192.168.1.101
*Jul 26 10:51:26.667: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 peerQ un/re
ly 0/0
*Jul 26 10:51:28.451: EIGRP: Sending HELLO on FastEthernet0/0
*Jul 26 10:51:28.451: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0
*Jul 26 10:51:29.027: EIGRP: Sending HELLO on Serial0/0/0
*Jul 26 10:51:29.027: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0
*Jul 26 10:51:31.383: EIGRP: Received HELLO on Serial0/0/0 nbr 192.168.1.101
*Jul 26 10:51:31.383: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 peerQ un/re
ly 0/0
*Jul 26 10:51:33.339: EIGRP: Sending HELLO on FastEthernet0/0
*Jul 26 10:51:33.339: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0
*Jul 26 10:51:33.511: EIGRP: Sending HELLO on Serial0/0/0
*Jul 26 10:51:33.511: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0
*Jul 26 10:51:36.347: EIGRP: Received HELLO on Serial0/0/0 nbr 192.168.1.101
*Jul 26 10:51:36.347: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 peerQ un/re
ly 0/0
*Jul 26 10:51:37.847: EIGRP: Sending HELLO on Serial0/0/0
*Jul 26 10:51:37.847: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0
*Jul 26 10:51:37.899: EIGRP: Sending HELLO on FastEthernet0/0
Transmisión Traces y recepción de paquetes EIGRP.
![Page 88: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/88.jpg)
Chapter 2 88 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Passive-Interface
Prevenir actualizaciones de EIGRP en una interfaz del
router especificada. Router(config-router)#
passive-interface type number [default]
Configure una interfaz determinada o todas las interfaces del router para pasivos.
La opción por defecto establece todos las interfaces del router en pasivo.
Para EIGRP, el comando:
Evita relaciones de vecindad que se establezca.
Se ignoran actualizaciones de enrutamiento de un vecino.
Permite una subred en una interfaz pasiva que se anunciará en EIGRP.
![Page 89: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/89.jpg)
Chapter 2 89 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Passive-Interface Example
R1(config)# router eigrp 100
R1(config-router)# passive-interface fa0/0
R1(config-router)#
R2(config)# router eigrp 100
R2(config-router)# passive-interface fa0/0
R2(config-router)#
Alternate configuration:
R1(config)# router eigrp 100
R1(config-router)# passive-interface default
R1(config-router)# no passive-interface S0/0/0
R2(config)# router eigrp 100
R2(config-router)# passive-interface default
R2(config-router)# no passive-interface S0/0/0
Fa0/0 Fa0/0
R1 R2
172.16.1.0 /24
EIGRP AS 100
Internet
192.168.1.0 /27
172.17.2.0 /24
64 kbps 192.168.1.96 /27
.101
.102 S0/0/1
S0/0/0 S0/0/0
.1
.1 .1
![Page 90: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/90.jpg)
Chapter 2 90 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Propagating a Default Route
Para propagar una ruta por defecto en EIGRP, use el
comando en modo de configuración global:
ip default-network network-number
Or
ip route 0.0.0.0 0.0.0.0 next-hop | interface router.
Una vez configurado, la ruta por defecto tiene que ser
propagado en el EIGRP AS.
![Page 91: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/91.jpg)
Chapter 2 91 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
ip default-network Command
Configura un router para notificar la red como el Gateway de último
recurso.
Router(config)#
ip default-network network
Otros routers utilizan su dirección del siguiente salto a la red se anuncia como su ruta por defecto.
No existe ningún parámetro para especificar la máscara de subred, por tanto, el comando sólo se puede utilizar para anunciar una red con clase (Classful).
La red especificada debe ser accesible antes de que se configure.
Si la red especificada no es accesible a través de:
EIGRP, a continuación, la ruta por defecto se propaga automáticamente a otros routers EIGRP en el AS.
Una ruta estática, a continuación, la ruta estática debe ser redistribuido en EIGRP.
![Page 92: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/92.jpg)
Chapter 2 92 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
ip default-network Example
R2# show ip route
<output omitted>
Gateway of last resort is not set
172.17.0.0/16 is variably subnetted, 2 subnets, 2 masks
D 172.17.0.0/16 is a summary, 02:27:56, Null0
C 172.17.2.0/24 is directly connected, FastEthernet0/0
D 172.16.0.0/16 [90/40514560] via 192.168.1.101, 02:27:56, Serial0/0/0
192.168.1.0/27 is subnetted, 2 subnets
C 192.168.1.96 is directly connected, Serial0/0/0
C 192.168.1.0 is directly connected, Serial0/0/1
R2#
R1# show ip route
<output omitted>
Gateway of last resort is not set
<output omitted>
Fa0/0 Fa0/0
R1 R2
172.16.1.0 /24
64 kbps
EIGRP AS 100
Internet
172.31.0.0 /16 192.168.1.96 /27
172.17.2.0 /24
.101
.102 S0/0/1
S0/0/0 S0/0/0
.1
.1 .1 192.168.1.0 /27
.2
![Page 93: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/93.jpg)
Chapter 2 93 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
ip default-network Example
Fa0/0 Fa0/0
R1 R2
172.16.1.0 /24
64 kbps
EIGRP AS 100
Internet
172.31.0.0 /16 192.168.1.96 /27
172.17.2.0 /24
.101
.102 S0/0/1
S0/0/0 S0/0/0
.1
.1 .1 192.168.1.0 /27
.2
R2(config)# ip route 172.31.0.0 255.255.0.0 192.168.1.2
R2(config)# do ping 172.31.0.0
<output omitted>
Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms
R2(config)# ip default-network 172.31.0.0
R2(config)# router eigrp 100
R2(config-router)# redistribute static
R2(config-router)# end
R2#
![Page 94: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/94.jpg)
Chapter 2 94 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
ip default-network Example
R2# show ip route
<output omitted>
Gateway of last resort is 192.168.1.2 to network 172.31.0.0
<output omitted>
S* 172.31.0.0/16 [1/0] via 192.168.1.2
192.168.1.0/27 is subnetted, 2 subnets
C 192.168.1.96 is directly connected, Serial0/0/0
C 192.168.1.0 is directly connected, Serial0/0/1
R2#
Fa0/0 Fa0/0
R1 R2
172.16.1.0 /24
64 kbps
EIGRP AS 100
Internet
172.31.0.0 /16 192.168.1.96 /27
172.17.2.0 /24
.101
.102 S0/0/1
S0/0/0 S0/0/0
.1
.1 .1 192.168.1.0 /27
.2
R1# show ip route
<output omitted>
Gateway of last resort is 192.168.1.102 to network 172.31.0.0
<output omitted.
D*EX 172.31.0.0/16 [170/41024000] via 192.168.1.102, 00:00:20, Serial0/0/0
192.168.1.0/27 is subnetted, 1 subnets
C 192.168.1.96 is directly connected, Serial0/0/0
R1#
![Page 95: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/95.jpg)
Chapter 2 95 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
ip route 0.0.0.0 0.0.0.0 next-hop |
interface Command Configura un router para anunciar una ruta por defecto como el
Gateway de último recurso.
Router(config)#
ip route 0.0.0.0 0.0.0.0 interface | next-hop
La elección del parámetro afecta a la siguiente selección de comandos.
Si se usa el parámetro de la interfaz, entonces sólo la red 0.0.0.0 necesita también ser introducido.
Si se utiliza el parámetro next-hop, entonces la red 0.0.0.0 y el comando redistribute static deben configurarse.
![Page 96: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/96.jpg)
Chapter 2 96 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
ip route 0.0.0.0 0.0.0.0 interface
Example
Fa0/0 Fa0/0
R1 R2
172.16.1.0 /24
64 kbps
EIGRP AS 100
Internet
172.31.0.0 /16 192.168.1.96 /27
172.17.2.0 /24
.101
.102 S0/0/1
S0/0/0 S0/0/0
.1
.1 .1 192.168.1.0 /27
.2
R2(config)# ip route 0.0.0.0 0.0.0.0 S0/0/1
R2(config)# router eigrp 100
R2(config-router)# network 0.0.0.0
R2(config-router)# do show ip route
<output omitted>
Gateway of last resort is 0.0.0.0 to network 0.0.0.0
172.17.0.0/16 is variably subnetted, 2 subnets, 2 masks
D 172.17.0.0/16 is a summary, 03:13:25, Null0
C 172.17.2.0/24 is directly connected, FastEthernet0/0
D 172.16.0.0/16 [90/40514560] via 192.168.1.101, 03:13:25, Serial0/0/0
192.168.1.0/27 is subnetted, 2 subnets
C 192.168.1.96 is directly connected, Serial0/0/0
C 192.168.1.0 is directly connected, Serial0/0/1
S* 0.0.0.0/0 is directly connected, Serial0/0/1
R2(config-router)#
![Page 97: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/97.jpg)
Chapter 2 97 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
ip route 0.0.0.0 0.0.0.0 next-hop Example
Fa0/0 Fa0/0
R1 R2
172.16.1.0 /24
64 kbps
EIGRP AS 100
Internet
172.31.0.0 /16 192.168.1.96 /27
172.17.2.0 /24
.101
.102 S0/0/1
S0/0/0 S0/0/0
.1
.1 .1 192.168.1.0 /27
.2
R2(config)# ip route 0.0.0.0 0.0.0.0 192.168.1.2
R2(config)# router eigrp 100
R2(config-router)# network 0.0.0.0
R2(config-router)# redistribute static
R2(config-router)# do show ip route
<output omitted>
Gateway of last resort is 192.168.1.2 to network 0.0.0.0
172.17.0.0/16 is variably subnetted, 2 subnets, 2 masks
D 172.17.0.0/16 is a summary, 02:53:48, Null0
C 172.17.2.0/24 is directly connected, FastEthernet0/0
D 172.16.0.0/16 [90/40514560] via 192.168.1.101, 02:53:48, Serial0/0/0
192.168.1.0/27 is subnetted, 2 subnets
C 192.168.1.96 is directly connected, Serial0/0/0
C 192.168.1.0 is directly connected, Serial0/0/1
S* 0.0.0.0/0 [1/0] via 192.168.1.2
R2(config-router)#
![Page 98: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/98.jpg)
Chapter 2 98 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Route Summarization
EIGRP resume automáticamente las rutas de una
importante al borde de la red de forma predeterminada.
• Debido al comando de configuración del router auto-summary pre-
configurado..
• En la mayoría de los casos, el resumen automático es una buena
cosa, ya que mantiene las tablas de enrutamiento lo más compacto
posible.
• A veces no es una cosa tan buena como cuando hay una subred
discontiguous.
Normalmente para el enrutamiento funcione correctamente,
el resumen automático debe ser desactivada con el
comando de configuración del router no auto-summary.
![Page 99: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/99.jpg)
Chapter 2 99 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Summarization in Discontiguous Networks
R1 R2
10.10.10.0 /24
EIGRP AS 100
192.168.1.96 /30 10.20.20.0 /24
EIGRP Update: Connected to 10.0.0.0 /8
R1# show running-config | section router eigrp
router eigrp 100
passive-interface FastEthernet0/0
network 10.10.10.0 0.0.0.255
network 192.168.1.96 0.0.0.31
auto-summary
R1# show ip protocols
Routing Protocol is "eigrp 100"
<output omitted>
Automatic network summarization is in effect
Automatic address summarization:
10.0.0.0/8 for Serial0/0/0
Summarizing with metric 28160
Maximum path: 4
Routing for Networks:
10.10.10.0/24
192.168.1.96/27
Passive Interface(s):
FastEthernet0/0
<output omitted>
![Page 100: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/100.jpg)
Chapter 2 100 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Summarization in Discontiguous Networks
R2# show ip route
<output omitted>
Gateway of last resort is 192.168.1.2 to network 0.0.0.0
10.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
C 10.20.20.0/24 is directly connected, FastEthernet0/0
D 10.0.0.0/8 is a summary, 00:13:35, Null0
192.168.1.0/27 is subnetted, 2 subnets
C 192.168.1.96 is directly connected, Serial0/0/0
C 192.168.1.0 is directly connected, Serial0/0/1
S* 0.0.0.0/0 [1/0] via 192.168.1.2
R2#
R1 R2
10.10.10.0 /24
EIGRP AS 100
192.168.1.96 /30 10.20.20.0 /24
EIGRP Update: Connected to 10.0.0.0 /8
R2 ignores the R1 update because it is already
connected to the classful 10.0.0.0/8 network.
![Page 101: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/101.jpg)
Chapter 2 101 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Null 0
Observe que la ruta resumida (10.0.0.0 / 8) tiene una
entrada que señala a Null0.
• Null0 se añade automáticamente a la tabla y se denominan rutas de
resumen.
• Null 0 es una conexión directa, la interfaz de software
exclusivamente.
• El uso de la interfaz null0 evita que el enrutador de tratar de desviar el
tráfico a otros routers en busca de una más precisa partido.
R2# show ip route
<output omitted>
Gateway of last resort is 192.168.1.2 to network 0.0.0.0
10.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
C 10.20.20.0/24 is directly connected, FastEthernet0/0
D 10.0.0.0/8 is a summary, 00:13:35, Null0
192.168.1.0/27 is subnetted, 2 subnets
C 192.168.1.96 is directly connected, Serial0/0/0
C 192.168.1.0 is directly connected, Serial0/0/1
S* 0.0.0.0/0 [1/0] via 192.168.1.2
R2#
![Page 102: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/102.jpg)
Chapter 2 102 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Disabling Automatic Summarization
R1 R2
10.10.10.0 /24
EIGRP AS 100
192.168.1.96 /30 10.20.20.0 /24
EIGRP Update: Connected to 10.0.0.0 /8
R1(config)# router eigrp 100
R1(config-router)# no auto-summary
R1(config-router)#
*Jul 26 22:14:07.183: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 192.168.1.102
(Serial0/0/0) is resync: summary configured
R1(config-router)# end
R1# show ip protocols
Routing Protocol is "eigrp 100“
<output omitted>
Automatic network summarization is not in effect
Maximum path: 4
Routing for Networks:
10.10.10.0/24
192.168.1.96/27
<output omitted>
![Page 103: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/103.jpg)
Chapter 2 103 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Disable Automatic Summarization
R1 R2
10.10.10.0 /24
EIGRP AS 100
192.168.1.96 /30 10.20.20.0 /24
EIGRP Update: Connected to 10.0.0.0 /8
R2(config)# router eigrp 100
R2(config)# no auto-summary
R2(config)# end
R2# show ip route
<output omitted>
Gateway of last resort is 192.168.1.2 to network 0.0.0.0
10.0.0.0/24 is subnetted, 2 subnets
C 10.20.20.0 is directly connected, FastEthernet0/0
D 10.10.10.0 [90/40514560] via 192.168.1.101, 00:05:21, Serial0/0/0
192.168.1.0/27 is subnetted, 2 subnets
C 192.168.1.96 is directly connected, Serial0/0/0
C 192.168.1.0 is directly connected, Serial0/0/1
S* 0.0.0.0/0 [1/0] via 192.168.1.2
R2#
![Page 104: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/104.jpg)
Chapter 2 104 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Summarizing on an Interface
Protocolos de vector de distancia anteriores fueron
incapaces de crear rutas de resumen que no sean los
bordes con clase o / 8, / 16 / o / 24.
Para hacer frente a esta deficiencia, EIGRP añadió el
comando de configuración en la interfaz, ip summary-
address eigrp.
• El comando se utiliza para crear una o más rutas de resumen dentro
de una red en cualquier frontera de bit (siempre y cuando exista una
ruta más específica en la tabla de enrutamiento).
Las rutas IP EIGRP summary tiene un valor de distancia
administrativa de 5.
• Rutas EIGRP estándar reciben una distancia administrativa de 90.
• Rutas EIGRP externos reciben una distancia administrativa de 170.
![Page 105: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/105.jpg)
Chapter 2 105 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
ip summary-address eigrp
Manually create a summary route at an arbitrary bit boundary.
Router(config-if)#
ip summary-address eigrp as-number address mask [admin-distance]
Parameter Description
as-number
Identificar el número de la AS EIGRP.
address La dirección IP que se anuncia como la dirección de
resumen. Esta dirección no tiene que ser alineado en
Clase A, B, C o límites.
mask
La máscara de subred IP que se utiliza para crear la
dirección de resumen.
admin-distance (Opcional) La distancia administrativa. Un valor de 0
a 255.
![Page 106: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/106.jpg)
Chapter 2 106 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Route Summarization
R1(config)# router eigrp 100
R1(config)# no auto-summary
R2(config)# router eigrp 100
R2(config)# no auto-summary
Fa0/0 Fa0/0
R1 R2
10.10.10.0 /24
EIGRP AS 100
WAN
192.168.3.1
S0/0/0
10.10.20.0 /24
10.0.0.0 /8
R3
R3(config)# interface S0/0/0
R3(config-if)# ip address 192.168.3.1 255.255.255.0
R3(config-if)# ip summary-address eigrp 1 10.10.0.0 255.255.0.0
R3(config-if)# no shut
R3(config-if)# exit
R3# show ip protocols
Routing Protocol is "eigrp 100"
<output omitted>
Automatic network summarization is not in effect
Address Summarization:
10.10.0.0/16 for Serial0/0/0
<output omitted>
![Page 107: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/107.jpg)
Chapter 2 107 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Configuring and Verifying EIGRP in an Enterprise WAN
![Page 108: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/108.jpg)
Chapter 2 108 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP and WAN Considerations
Hay varias opciones de implementación disponibles para
apoyar EIGRP en una WAN, incluyendo:
• Frame Relay
• Frame-Relay usando mapeo dinámico.
• Frame-Relay utilizando asignación estática.
• Subinterfaces multipunto y punto a punto Frame-Relay.
• Multiprotocol Label Switching (MPLS) de redes privadas virtuales
(VPN), Ethernet sobre Multiprotocol Label Switching (EoMPLS).
Otras consideraciones incluyen:
• Balanceo de carga EIGRP.
• Limitar el ancho de banda utilización EIGRP en enlaces WAN.
![Page 109: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/109.jpg)
Chapter 2 109 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Frame Relay Using Dynamic Mapping
Despliegue fácil debido a la utilización de ARP inversa.
Detecta automáticamente la mayoría de las
configuraciones.
ARP inverso asignará dinámicamente las direcciones IP de
los dispositivos en los otros extremos de los PVC al número
DLCI local.
Consta de tres pasos:
1. Configure una dirección IP en la interfaz en serie.
2. Cambie la encapsulación en una interfaz con el comando
encapsulation frame-relay.
3. Activar la interfaz.
![Page 110: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/110.jpg)
Chapter 2 110 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Frame Relay Using Dynamic Mapping
R1(config)# interface S0/0/0
R1(config-if)# encapsulation frame-relay
R1(config-if)# ip address 192.168.1.101 255.255.255.0
R1(config-if)# exit
R1(config)# router eigrp 100
R1(config-router)# network 172.16.1.0 0.0.0.255
R1(config-router)# network 192.168.1.0
R1(config-router)#
R3(config)# interface S0/0/0
R3(config-if)# encapsulation frame-relay
R3(config-if)# ip address 192.168.1.103 255.255.255.0
R3(config-if)# exit
R3(config)# router eigrp 100
R3(config-router)# network 172.16.3.0 0.0.0.255
R3(config-router)# network 192.168.1.0
R3(config-router)#
Fa0/0
R1
172.16.1.0 /24
EIGRP AS 100
Frame Relay
R2
R3
S0/0/0 192.168.1.0 /24
.101
.103
.102
S0/0/0
S0/0/0
DLCI 103
DLCI 102 DLCI 201
DLCI 301
Fa0/0 172.16.2.0 /24
Fa0/0 172.16.3.0 /24
![Page 111: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/111.jpg)
Chapter 2 111 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Frame Relay Using Dynamic Mapping
R1# show ip eigrp neighbors
IP-EIGRP neighbors for process 100
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
0 192.168.1.102 Se0/0/0 10 00:07:22 10 2280 0 5
1 192.168.1.103 Se0/0/0 10 00:09:34 10 2320 0 9
R1#
R3# show ip eigrp neighbors
IP-EIGRP neighbors for process 100
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
0 192.168.1.101 Se0/0/0 10 00:11:45 10 1910 0 6
R3#
Fa0/0
R1
172.16.1.0 /24
EIGRP AS 100
Frame Relay
R2
R3
S0/0/0 192.168.1.0 /24
.101
.103
.102
S0/0/0
S0/0/0
DLCI 103
DLCI 102 DLCI 201
DLCI 301
Fa0/0 172.16.2.0 /24
Fa0/0 172.16.3.0 /24
![Page 112: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/112.jpg)
Chapter 2 112 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Frame Relay Using Static Mapping
Implementación Static Maps desactiva automáticamente la
función inversa de la ARP.
Consta de cuatro pasos:
1. Configure una dirección IP de la interfaz serial.
2. Cambie la encapsulación en una interfaz con el comando
encapsulation frame-relay.
3. Mapeo de IP a DLCI sobre la interfaz con el comando frame-relay
map.
4. Activar la interfaz.
![Page 113: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/113.jpg)
Chapter 2 113 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
frame-relay map Command
Asigne estáticamente la dirección IP del router remoto en
el DLCI local.
Router(config-if)#
frame-relay map protocol protocol-address dlci [broadcast] [ietf |
cisco] [payload-compress {packet-by-packet | frf9 stack}]
Parameter Description
protocol Define el protocolo soportado, hacer puentes, o control de enlace lógico.
protocol-address Define la dirección de capa de red de la interfaz del router destino.
dlci Define el DLCI local que se utiliza para conectarse a la dirección de protocolo
remoto.
broadcast ((Opcional) Permite broadcast y multicast sobre el VC, permitiendo el uso de
protocolos de enrutamiento dinámico en el VC.
ietf | cisco Habilita la encapsulacion IETF o Cisco.
payload-compress (Opcional) Permite la compresión de la carga útil.
packet-by-packet (Opcional) Permite la compresión de carga útil del paquete a paquete, usando
el método de Stacker, un método de compresión propiedad de Cisco.
frf9 stac (Opcional) Permite la compresión FRF.9 utilizando el método de Stacker.
![Page 114: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/114.jpg)
Chapter 2 114 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Frame Relay Using Static Mapping
R1(config)# interface S0/0/0
R1(config-if)# encapsulation frame-relay
R1(config-if)# ip address 192.168.1.101 255.255.255.0
R1(config-if)# frame-relay map ip 192.168.1.101 101
R1(config-if)# frame-relay map ip 192.168.1.102 102 broadcast
R1(config-if)# frame-relay map ip 192.168.1.103 103 broadcast
R1(config-if)#
R3(config)# interface S0/0/0
R3(config-if)# encapsulation frame-relay
R3(config-if)# ip address 192.168.1.103 255.255.255.0
R3(config-if)# frame-relay map ip 192.168.1.101 301
R3(config-if)# frame-relay map ip 192.168.1.102 301 broadcast
R3(config-if)# frame-relay map ip 192.168.1.103 301 broadcast
R3(config-if)#
Fa0/0
R1
172.16.1.0 /24
EIGRP AS 100
Frame Relay
R2
R3
S0/0/0 192.168.1.0 /24
.101
.103
.102
S0/0/0
S0/0/0
DLCI 103
DLCI 102 DLCI 201
DLCI 301
Fa0/0 172.16.2.0 /24
Fa0/0 172.16.3.0 /24
![Page 115: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/115.jpg)
Chapter 2 115 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Frame Relay Using Static Mapping
R1# show ip eigrp neighbors
IP-EIGRP neighbors for process 100
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
0 192.168.1.102 Se0/0/0 10 00:06:20 10 2280 0 5
1 192.168.1.103 Se0/0/0 10 00:08:31 10 2320 0 9
R3# show ip eigrp neighbors
IP-EIGRP neighbors for process 100
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
0 192.168.1.101 Se0/0/0 10 00:10:44 10 1910 0 6
1 192.168.1.102 Se0/0/0 10 00:03:02 10 2210 0 3
Fa0/0
R1
172.16.1.0 /24
EIGRP AS 100
Frame Relay
R2
R3
S0/0/0 192.168.1.0 /24
.101
.103
.102
S0/0/0
S0/0/0
DLCI 103
DLCI 102 DLCI 201
DLCI 301
Fa0/0 172.16.2.0 /24
Fa0/0 172.16.3.0 /24
![Page 116: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/116.jpg)
Chapter 2 116 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP over FR Multipoint Subinterfaces
Subinterfaces multipunto se pueden crear utilizando una única interfaz física Frame Relay.
• Utiliza una única subred, conservando el espacio de direcciones IP.
Multipunto Frame Relay es aplicable a malla parcial y topologías de malla completa.
Se compone de varios pasos:
• Configure la interfaz física con ninguna dirección IP y cambiar la encapsulación de Frame Relay.
• Crear una subinterfaz multipunto serial.
• Configure una dirección IP en la interfaz serial.
• Mapa de los comandos de IP a DLCI de mapeo en la interfaz con el comando frame-relay map.
• Cualquiera de depender de mapeo dinámico o configurar un valor DLCI local con el comando frame-relay interface-dlci.
![Page 117: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/117.jpg)
Chapter 2 117 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP over FR Multipoint Subinterfaces
Subinterfaces multipunto se configuran con el comando interface serial number.subinterface-number
multipoint.
La asignación de direcciones IP a DLCI se hace por
cualquiera:
• Especificar el valor DLCI local (utilizando la interfaz con el comando
frame-relay interface-dlci dlci) y basándose en el ARP inverso.
• El uso de IP mapeo manual de dirección a DLCI.
![Page 118: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/118.jpg)
Chapter 2 118 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP over FR Multipoint Subinterfaces
Fa0/0
R1
172.16.1.0 /24
EIGRP AS 100
Frame Relay
R2
R3
192.168.1.0 /24 .103
.102
S0/0/0.1
S0/0/0.1
DLCI 103
DLCI 102 DLCI 201
DLCI 301
Fa0/0 172.16.2.0 /24
Fa0/0 172.16.3.0 /24
S0/0/0.1
.101
R1(config)# interface S0/0/0
R1(config-if)# no ip address
R1(config-if)# encapsulation frame-relay
R1(config-if)# exit
R1(config)# interface Serial0/0/0.1 multipoint
R1(config-subif)# ip address 192.168.1.101 255.255.255.0
R1(config-subif)# no ip split-horizon eigrp 100
R1(config-subif)# frame-relay map ip 192.168.1.101 101
R1(config-subif)# frame-relay map ip 192.168.1.102 102 broadcast
R1(config-subif)# frame-relay map ip 192.168.1.103 103 broadcast
R1(config-subif)#
![Page 119: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/119.jpg)
Chapter 2 119 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP over FR Multipoint Subinterfaces
R1# show ip eigrp neighbors
IP-EIGRP neighbors for process 100
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
0 192.168.1.102 Se0/0/0.1 10 00:06:41 10 2280 0 5
1 192.168.1.103 Se0/0/0.1 10 00:08:52 10 2320 0 9
R3# show ip eigrp neighbors
IP-EIGRP neighbors for process 100
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
0 192.168.1.101 Se0/0/0.1 10 00:10:37 10 1910 0 6
1 192.168.1.102 Se0/0/0.1 10 00:03:12 10 2210 0 3
Fa0/0
R1
172.16.1.0 /24
EIGRP AS 100
Frame Relay
R2
R3
192.168.1.0 /24 .103
.102
S0/0/0.1
S0/0/0.1
DLCI 103
DLCI 102 DLCI 201
DLCI 301
Fa0/0 172.16.2.0 /24
Fa0/0 172.16.3.0 /24
S0/0/0.1
.101
![Page 120: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/120.jpg)
Chapter 2 120 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Unicast Neighbors
Definir un router vecino para intercambiar información de enrutamiento
EIGRP.
Router(config-router)#
neighbor {ip-address | ipv6-address} interface-type
interface-number
Intercambios información de enrutamiento EIGRP con el vecino especificado utilizando paquetes unicast.
Estados vecinos múltiples pueden ser utilizados para establecer sesiones de peering con múltiples vecinos EIGRP específicas.
La interfaz a través del cual EIGRP intercambiar actualizaciones de enrutamiento se debe especificar en la declaración vecino.
Las interfaces a través del cual dos vecinos EIGRP intercambiar actualizaciones de enrutamiento se deben configurar con direcciones IP de la misma red.
![Page 121: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/121.jpg)
Chapter 2 121 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Unicast Neighbors
Fa0/0
R1
172.16.1.0 /24
EIGRP AS 100
Frame Relay
R2
R3
192.168.1.0 /24 .103
.102
S0/0/0.1
S0/0/0.1
DLCI 103
DLCI 102 DLCI 201
DLCI 301
Fa0/0 172.16.2.0 /24
Fa0/0 172.16.3.0 /24
S0/0/0.1
.101
R1(config)# interface S0/0/0
R1(config-if)# no ip address
R1(config-if)# encapsulation frame-relay
R1(config-if)# interface S0/0/0.1 multipoint
R1(config-subif)# ip address 192.168.1.101 255.255.255.0
R1(config-subif)# frame-relay map ip 192.168.1.102 102 broadcast
R1(config-subif)# frame-relay map ip 192.168.1.103 103 broadcast
R1(config-subif)# router eigrp 100
R1(config-router)# neighbor 192.168.1.102 S0/0/0.1
R1(config-router)#
![Page 122: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/122.jpg)
Chapter 2 122 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Unicast Neighbors
Fa0/0
R1
172.16.1.0 /24
EIGRP AS 100
Frame Relay
R2
R3
192.168.1.0 /24 .103
.102
S0/0/0.1
S0/0/0.1
DLCI 103
DLCI 102 DLCI 201
DLCI 301
Fa0/0 172.16.2.0 /24
Fa0/0 172.16.3.0 /24
S0/0/0.1
.101
R2(config)# interface S0/0/0
R2(config-if)# no ip address
R2(config-if)# encapsulation frame-relay
R2(config-if)# interface S0/0/0.1 multipoint
R2(config-subif)# ip address 192.168.1.102 255.255.255.0
R2(config-subif)# frame-relay map ip 192.168.1.101 201 broadcast
R2(config-subif)# router eigrp 100
R2(config-router)# neighbor 192.168.1.101 S0/0/0.1
R2(config-router)#
![Page 123: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/123.jpg)
Chapter 2 123 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP over FR Point-to-Point Subinterfaces
Subinterfaces punto a punto se pueden crear utilizando una
única interfaz física Frame Relay.
• Utiliza varias subredes.
Frame Relay punto a punto es aplicable a hub and spoke
topologías.
Se compone de varios pasos:
• Configure la interfaz física con ninguna dirección IP y cambiar la
encapsulación de Frame Relay.
• Crear una subinterfaz serial punto a punto.
• Configure una dirección IP en la interfaz serial.
• Configure un valor DLCI local con el comando frame-relay interface-
dlci.
![Page 124: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/124.jpg)
Chapter 2 124 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP over FR Point-to-Point Subinterfaces
Subinterfaces multipunto se configuran con el comando interface serial number.subinterface-number
multipoint.
La asignación de direcciones IP a DLCI se hace ya sea por:
• Especificar el valor DLCI local (utilizando la interfaz con el comando
frame-relay interface-dlci dlci) y basándose en el ARP inverso.
![Page 125: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/125.jpg)
Chapter 2 125 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP over FR Point-to-Point Subinterfaces
R1(config)# interface S0/0/0
R1(config-if)# no ip address
R1(config-if)# encapsulation frame-relay
R1(config-if)# exit
R1(config)# interface Serial0/0/0.2 point-to-point
R1(config-subif)# ip address 192.168.2.101 255.255.255.0
R1(config-subif)# frame-relay interface-dlci 102
R1(config-subif)#
R1(config-subif)# interface Serial0/0/0.3 point-to-point
R1(config-subif)# ip address 192.168.3.101 255.255.255.0
R1(config-subif)# frame-relay interface-dlci 103
R1(config-subif)#
Fa0/0
R1
172.16.1.0 /24
EIGRP AS 100
Frame Relay
R2
R3
192.168.3.103
S0/0/0.1
S0/0/0.1
DLCI 103
DLCI 102 DLCI 201
DLCI 301
Fa0/0 172.16.2.0 /24
Fa0/0 172.16.3.0 /24
S0/0/0.3=192.168.3.101/24
192.168.2.102
S0/0/0.2=192.168.2.101/24
![Page 126: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/126.jpg)
Chapter 2 126 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP over FR Point-to-Point Subinterfaces
R1# show ip eigrp neighbors
IP-EIGRP neighbors for process 100
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
0 192.168.2.102 Se0/0/0.2 10 00:08:04 10 2280 0 5
1 192.168.3.103 Se0/0/0.3 10 00:10:12 10 2320 0 9
R3# show ip eigrp neighbors
IP-EIGRP neighbors for process 100
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
0 192.168.3.101 Se0/0/0.1 10 00:13:25 10 1910 0 6
Fa0/0
R1
172.16.1.0 /24
EIGRP AS 100
Frame Relay
R2
R3
192.168.3.103
S0/0/0.1
S0/0/0.1
DLCI 103
DLCI 102 DLCI 201
DLCI 301
Fa0/0 172.16.2.0 /24
Fa0/0 172.16.3.0 /24
S0/0/0.3=192.168.3.101/24
192.168.2.102
S0/0/0.2=192.168.2.101/24
![Page 127: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/127.jpg)
Chapter 2 127 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP over MPLS
Multi-Protocol Label Switching (MPLS) es una arquitectura
estándar de Internet Engineering Task Force (IETF), que
combina las ventajas de enrutamiento de nivel 3, con los
beneficios de la conmutación de Capa 2.
Una característica única de MPLS es su capacidad para
llevar a cabo de apilamiento de etiquetas, en el que varias
etiquetas pueden ser transportados en un paquete.
La etiqueta de la parte superior, que es el último en el,
siempre se procesa primero.
• Apilamiento de etiquetas permite que varios proveedores de servicios
lingüísticos para ser agregados, creando túneles a través de múltiples
niveles de una red MPLS.
![Page 128: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/128.jpg)
Chapter 2 128 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP over Layer 3 MPLS VPNs
R1(config)# interface FastEthernet0/0
R1(config-if)# ip address 192.168.1.2 255.255.255.252
R1(config-if)# exit
R1(config)# router eigrp 100
R1(config-router)# network 172.16.1.0 0.0.0.255
R1(config-router)# network 192.168.1.0
R1(config-router)#
R2(config)# interface FastEthernet0/0
R2(config-if)# ip address 192.168.2.2 255.255.255.252
R2(config-if)# exit
R2(config)# router eigrp 100
R2(config-router)# network 172.17.2.0 0.0.0.255
R2(config-router)# network 192.168.2.0
R2(config-router)#
EIGRP AS 100
Layer 3 MPLS
VPN Backbone Fa0/0 PE1
.1
PE2
192.168.2.0/30
.2 .2
192.168.1.0/30
.1
EIGRP AS 100
Fa0/0
172.16.1.0 /24 172.17.2.0 /24
R2 R1
![Page 129: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/129.jpg)
Chapter 2 129 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP over Layer 3 MPLS VPNs
R1# show ip eigrp neighbors
IP-EIGRP neighbors for process 100
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
0 192.168.1.1 Fe0/0 10 00:07:22 10 2280 0 5
R2# show ip eigrp neighbors
IP-EIGRP neighbors for process 100
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
0 192.168.2.1 Fe0/0 10 00:17:02 10 1380 0 5
EIGRP AS 100
Layer 3 MPLS
VPN Backbone Fa0/0 PE1
.1
PE2
192.168.2.0/30
.2 .2
192.168.1.0/30
.1
EIGRP AS 100
Fa0/0
172.16.1.0 /24 172.17.2.0 /24
R2 R1
![Page 130: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/130.jpg)
Chapter 2 130 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP over Layer 2 MPLS VPNs
R1(config)# interface FastEthernet0/0
R1(config-if)# ip address 192.168.1.101 255.255.255.224
R1(config-if)# exit
R1(config)# router eigrp 100
R1(config-router)# network 172.16.1.0 0.0.0.255
R1(config-router)# network 192.168.1.0
R1(config-router)#
R2(config)# interface FastEthernet0/0
R2(config-if)# ip address 192.168.1.102 255.255.255.224
R2(config-if)# exit
R2(config)# router eigrp 100
R2(config-router)# network 172.17.2.0 0.0.0.255
R2(config-router)# network 192.168.1.0
R2(config-router)#
EIGRP AS 100
Layer 2 MPLS
VPN Backbone Fa0/0 PE1 PE2
192.168.1.0/27
.102 .101
192.168.1.0/27
EIGRP AS 100
Fa0/0
172.16.1.0 /24 172.17.2.0 /24
R2 R1
![Page 131: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/131.jpg)
Chapter 2 131 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP over Layer 2 MPLS VPNs
R1# show ip eigrp neighbors
IP-EIGRP neighbors for process 100
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
0 192.168.1.102 Fe0/0 10 00:07:22 10 2280 0 5
R2# show ip eigrp neighbors
IP-EIGRP neighbors for process 100
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
0 192.168.1.101 Fe0/0 10 00:17:02 10 1380 0 5
EIGRP AS 100
Layer 2 MPLS
VPN Backbone Fa0/0 PE1 PE2
192.168.1.0/27
.102 .101
192.168.1.0/27
EIGRP AS 100
Fa0/0
172.16.1.0 /24 172.17.2.0 /24
R2 R1
![Page 132: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/132.jpg)
Chapter 2 132 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Load Balancing
Las rutas con una métrica igual a la métrica mínimo se
instalan en la tabla de enrutamiento.
• Conocido como "balanceo de carga de igual coste”.
• Todos los protocolos de enrutamiento IP en los routers de Cisco
pueden realizar balanceo de carga de igual coste.
El comando maximum-paths maximum-path se puede
utilizar para permitir hasta 6 rutas de igual costo.
• Por defecto es 4.
• Configuración de la opción a 1 de maximum-path deshabilita
balanceo de carga.
![Page 133: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/133.jpg)
Chapter 2 133 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Equal-Cost Load Balancing
R1(config)# router eigrp 100
R1(config-router)# network 172.16.1.0 0.0.0.255
R1(config-router)# network 192.168.1.0
R1(config-router)# network 192.168.2.0
R1(config-router)# network 192.168.3.0
R1(config-router)# network 192.168.4.0
R1(config-router)# maximum–paths 3
R1(config-router)#
R1 Topology Table
Advertised Distance (AD)
Network Neighbor AD FD
172.16.2.0/24 R2 20 40
R3 20 40
R4 20 40
R5 20 40
![Page 134: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/134.jpg)
Chapter 2 134 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Unequal Cost Load Balancing
EIGRP también puede equilibrar el tráfico a través de múltiples rutas que tienen diferentes métricas.
• Conocido como balanceo de carga de costos desiguales.
El grado en que EIGRP realiza balanceo de carga es controlada con el comando variance multiplier.
• El multiplicador es un valor entre 1 y 128, que se utiliza para equilibrar la carga.
• El valor predeterminado es 1, lo que significa balanceo de carga de igual costo.
• El establecimiento de un valor de varianza mayor que 1 permite EIGRP instalar varias rutas sin bucles con coste desigual en la tabla de enrutamiento.
• EIGRP siempre instalará sucesores (las mejores rutas) en la tabla de enrutamiento.
• La varianza permite sucesores factibles (y rutas del sucesor único factible) como vías de candidatos potencialmente pueden instalar en la tabla de enrutamiento.
![Page 135: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/135.jpg)
Chapter 2 135 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Unequal-Cost Load Balancing
R1(config)# router eigrp 100
R1(config-router)# variance 2
R1(config-router)#
R1 Topology Table
Advertised Distance (AD)
Network Neighbor AD FD
172.16.2.0/24 R2 10 30
R3 10 20
R4 25 45
R5 10 50
![Page 136: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/136.jpg)
Chapter 2 136 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Bandwidth Use Across WAN Links
EIGRP funciona eficientemente en entornos WAN y es
escalable en ambos enlaces punto a punto y enlaces punto
a punto, multipunto y NBMA.
Sin embargo, la configuración por defecto de las
conexiones WAN no puede ser óptimo, por tanto, una
comprensión sólida de la operación de EIGRP junto con el
conocimiento de las velocidades de enlace puede generar
una configuración eficiente, confiable, escalable enrutador.
Hay dos comandos que pueden ser configurados para
mejorar el funcionamiento de EIGRP:
• bandwidth
• ip percent-bandwidth
![Page 137: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/137.jpg)
Chapter 2 137 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Setting EIGRP Bandwidth on a WAN
EIGRP supone el ancho de banda por defecto en el enlace en lugar del verdadero ancho de banda, la selección de rutas, por lo tanto puede resultar subóptimo. • Por ejemplo, los enlaces seriales comúnmente por defecto a 1,5 Mbps
sin embargo, el CIR real puede ser de 128 Kbps.
• DOBLE sería utilizar el valor de 1,5 Mbps en lugar de la más lenta del valor real de 128 Kbps en su cálculo de la métrica.
Se recomienda configurar el ajuste de ancho de banda utilizando bandwidth kilobits en las interfaces serial.
Una consideración importante WAN es el hecho de que la fijación de las interfaces físicas multipunto el ancho de banda es compartido por igual por todos los vecinos. • EIGRP utiliza el ajuste de ancho de banda de la interfaz física, dividido
por el número de Frame Relay vecinos conectados en esa interfaz física para conseguir el ancho de banda atribuida a cada vecino.
• La configuración de EIGRP debe reflejar el porcentaje correcto del ancho de banda real disponible en la línea.
![Page 138: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/138.jpg)
Chapter 2 138 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP WAN Configuration – Example #1
All VCs share the bandwidth evenly:
4 (VC) x 56 (CIR) = 224
CIR 56
R1
EIGRP AS 100
Frame Relay
R3
R4
R2
R5
CIR 56
CIR 56 CIR 56
T1 (1.5 Mbps)
S0/0/0
R1(config)# interface S0/0/0
R1(config-if)# encapsulation frame-relay
R1(config-if)# bandwidth 224
![Page 139: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/139.jpg)
Chapter 2 139 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP WAN Configuration – Example #2a
R2, R3 y R4 tienen el mismo CIR. Para protegerse contra sobrecargar el circuito más lento-velocidad (a R5) el ancho de banda debe ser configurado para el CIR menor multiplicado por el número de circuitos.
4 (VC) x 56 (CIR) = 224
R1(config)# interface S0/0/0
R1(config-if)# encapsulation frame-relay
R1(config-if)# bandwidth 224
R1
EIGRP AS 100
Frame Relay
R3
R4
R2
R5
T1 (1.5 Mbps)
S0/0/0
CIR 256 BW 224 CIR 256
BW 224
CIR 256 BW 224
CIR 56 BW 56
![Page 140: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/140.jpg)
Chapter 2 140 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP WAN Configuration – Example #2b
Una solución alternativa es configurar una subinterfaz multipunto para routers R2, R3 y R4 y configurar una red punto a punto de subinterfaz para R5.
R1
EIGRP AS 100
Frame Relay
R3
R4
R2
R5
T1 (1.5 Mbps)
S0/0/0
CIR 256 BW 224 CIR 256
BW 224
CIR 256 BW 224
CIR 56 BW 56
R1(config)# interface S0/0/0
R1(config-if)# encapsulation frame-relay
R1(config-if)# interface S0/0/0/0.1 multipoint
R1(config-subif)# bandwidth 768
R1(config-subif)# exit
R1(config)# interface S0/0/0/0.2 point-to-point
R1(config-subif)# bandwidth 56
R1(config-subif)#
![Page 141: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/141.jpg)
Chapter 2 141 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP ip bandwith-percent
Por defecto, EIGRP está configurado para utilizar hasta el
50% del ancho de banda de una interfaz para el
intercambio de información de enrutamiento.
El comando ip bandwidth-percent eigrp puede ser
configurado para controlar la cantidad de ancho de banda
disponible para EIGRP.
• Este no es el mismo que el comando bandwidth.
• Sin embargo, este comando se basa en el valor fijado por el comando
bandwidth.
![Page 142: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/142.jpg)
Chapter 2 142 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
ip bandwidth-percent eigrp
Configurar el ancho de banda disponible para EIGRP.
Router(config-if)#
ip bandwidth-percent eigrp as-number percent
Este as-number es el numero de Sistema Autonomo is
the EIGRP AS number.
El parámetro percent es el porcentaje de la anchura de
banda configurado que EIGRP puede utilizar.
El valor de porcentaje se puede ajustar a más de 100.
![Page 143: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/143.jpg)
Chapter 2 143 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Configuring and Verifying EIGRP Authentication
![Page 144: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/144.jpg)
Chapter 2 144 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Router Authentication
Muchos protocolos de enrutamiento se apoya con
autenticación de tal manera que un router autentica la
fuente de cada paquete de actualización de
encaminamiento que recibe.
Autenticación de contraseña simple está soportado por:
• IS-IS
• OSPF
• RIPv2
Autenticación MD5 está soportado por:
• OSPF
• RIPv2
• BGP
• EIGRP
![Page 145: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/145.jpg)
Chapter 2 145 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Simple Password vs. MD5 Authentication
Autenticación de contraseña simple:
• Router envía paquetes y clave.
• Vecino comprueba si la clave recibida coincide con su clave.
• No es seguro.
Autenticación MD5:
• Configure una "clave" (contraseña) y key-id; enrutador genera un
resumen del mensaje, o hash, de la clave, identificador de clave y
mensaje.
• Resumen del mensaje se envía con el paquete; no se envía la clave..
• Es seguro.
![Page 146: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/146.jpg)
Chapter 2 146 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP MD5 Authentication
EIGRP admite la autenticación MD5.
Router genera y comprueba todos los paquetes EIGRP.
Router autentica la fuente de cada paquete de actualización
de enrutamiento que recibe.
Configure una "clave" (contraseña) y key-id; cada vecino
participante debe tener la misma clave configurada.
![Page 147: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/147.jpg)
Chapter 2 147 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
MD5 Authentication
Autenticación MD5 EIGRP:
• Router genera un resumen del mensaje, o hash, de la clave, key-id y
el mensaje.
• EIGRP permite claves sean administrados por medio key chains.
• Especifica key-id (número, llave, y la vida útil de la llave).
• La primera llave activada válida, por orden de los números de clave,
se utiliza.
![Page 148: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/148.jpg)
Chapter 2 148 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Planning for EIGRP
Los siguientes parámetros de clave deben definirse con suficiente detalle antes de configurar la autenticación EIGRP :
• El número AS EIGRP
• El modo de autenticación (MD5).
• La definición de una o más claves para autenticar paquetes EIGRP, de acuerdo con el plan de seguridad de la red.
• Las claves lifetime definen varias claves.
Una vez definidos, los pasos siguientes pueden ser implementadas:
1. Configurar el modo de autenticación para EIGRP.
2. Configuración the key chain.
3. Opcionalmente, configure los parámetros lifetime de las llaves.
4. Habilitar la autenticación de usar la llave (s) en el key-chain.
![Page 149: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/149.jpg)
Chapter 2 149 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Configure the Authentication Mode for EIGRP
Especifique la autenticación MD5 para paquetes EIGRP.
Router(config-if)#
ip authentication mode eigrp autonomous-system md5
Habilitar la autenticación de paquetes EIGRP usando la llave el key-chain.
Router(config-if)#
ip authentication key-chain eigrp autonomous-system name-
of-chain
![Page 150: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/150.jpg)
Chapter 2 150 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Configure the Key Chain
Define the keychain in key chain configuration mode.
Router(config)#
key chain name-of-chain
Identify the key and enter the key-id configuration mode.
Router(config-keychain)#
key key-id
Router(config-keychain-key)#
key-string text
Identify key string (password)
![Page 151: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/151.jpg)
Chapter 2 151 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Configure Keys Lifetime Parameters (Optional)
Indique cuándo se aceptará la clave para los paquetes recibidos.
Router(config-keychain-key)#
accept-lifetime start-time {infinite | end-time |
duration seconds}
Especifica cuando la llave se puede utilizar para el envío de paquetes EIGRP.
Router(config-keychain-key)#
send-lifetime start-time {infinite | end-time |
duration seconds}
![Page 152: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/152.jpg)
Chapter 2 152 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Enable Authentication to Use the Key Chain
Habilitar la autenticación de paquetes EIGRP usando la llave key-chain.
Router(config-if)#
ip authentication key-chain eigrp autonomous-system
name-of-chain
![Page 153: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/153.jpg)
Chapter 2 153 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Configuring EIGRP MD5 Authentication
Fa0/0 Fa0/0
R1 R2
172.16.1.0 /24
EIGRP AS 100 R1# show running-config
!
<output omitted>
!
key chain R1chain
key 1
key-string FIRST-KEY
accept-lifetime 04:00:00 Jan 1 2009 infinite
send-lifetime 04:00:00 Jan 1 2009 04:00:00 Jan 31 2009
key 2
key-string SECOND-KEY
accept-lifetime 04:00:00 Jan 25 2009 infinite
send-lifetime 04:00:00 Jan 25 2009 infinite
!
<output omitted>
!
interface FastEthernet0/0
ip address 172.16.1.1 255.255.255.0
!
interface Serial0/0/0
bandwidth 64
ip address 192.168.1.101 255.255.255.224
ip authentication mode eigrp 100 md5
ip authentication key-chain eigrp 100 R1chain
!
router eigrp 100
network 172.16.1.0 0.0.0.255
network 192.168.1.0
auto-summary
172.17.2.0 /24
S0/0/0 S0/0/0
64 kbps
192.168.1.96 /27
.101
.102
.1 .1
![Page 154: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/154.jpg)
Chapter 2 154 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Configuring EIGRP MD5 Authentication
Fa0/0 Fa0/0
R1 R2
172.16.1.0 /24
EIGRP AS 100 R2# show running-config
!
<output omitted>
!
key chain R2chain
key 1
key-string FIRST-KEY
accept-lifetime 04:00:00 Jan 1 2009 infinite
send-lifetime 04:00:00 Jan 1 2009 infinite
key 2
key-string SECOND-KEY
accept-lifetime 04:00:00 Jan 25 2009 infinite
send-lifetime 04:00:00 Jan 25 2009 infinite
!
<output omitted>
!
interface FastEthernet0/0
ip address 172.17.2.2 255.255.255.0
!
interface Serial0/0/0
bandwidth 64
ip address 192.168.1.102 255.255.255.224
ip authentication mode eigrp 100 md5
ip authentication key-chain eigrp 100 R2chain
!
router eigrp 100
network 172.17.2.0 0.0.0.255
network 192.168.1.0
auto-summary
172.17.2.0 /24
S0/0/0 S0/0/0
64 kbps 192.168.1.96 /27
.101
.102
.1 .1
![Page 155: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/155.jpg)
Chapter 2 155 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Verifying MD5 Authentication
R1#
*Apr 21 16:23:30.517: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 192.168.1.102
(Serial0/0/0) is up: new adjacency
R1#
R1# show ip eigrp neighbors
IP-EIGRP neighbors for process 100
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
0 192.168.1.102 Se0/0/0 12 00:03:10 17 2280 0 14
R1#
R1# show ip route
<output omitted>
Gateway of last resort is not set
D 172.17.0.0/16 [90/40514560] via 192.168.1.102, 00:02:22, Serial0/0/0
172.16.0.0/16 is variably subnetted, 2 subnets, 2 masks
D 172.16.0.0/16 is a summary, 00:31:31, Null0
C 172.16.1.0/24 is directly connected, FastEthernet0/0
192.168.1.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.1.96/27 is directly connected, Serial0/0/0
D 192.168.1.0/24 is a summary, 00:31:31, Null0
R1#
R1# ping 172.17.2.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.17.2.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 12/15/16 ms
![Page 156: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/156.jpg)
Chapter 2 156 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Verifying MD5 Authentication
R1# show key chain
Key-chain R1chain:
key 1 -- text “FIRST-KEY"
accept lifetime (04:00:00 Jan 1 2009) - (always valid) [valid now]
send lifetime (04:00:00 Jan 1 2009) - (04:00:00 Jan 31 2009)
key 2 -- text “SECOND-KEY"
accept lifetime (04:00:00 Jan 25 2009) - (always valid) [valid now]
send lifetime (04:00:00 Jan 25 2009) - (always valid) [valid now]
![Page 157: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/157.jpg)
Chapter 2 157 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Troubleshooting MD5 Authentication
R1# debug eigrp packets
EIGRP Packets debugging is on
(UPDATE, REQUEST, QUERY, REPLY, HELLO, IPXSAP, PROBE, ACK, STUB, SIAQUERY, SIAREPLY)
*Jan 21 16:38:51.745: EIGRP: received packet with MD5 authentication, key id = 1
*Jan 21 16:38:51.745: EIGRP: Received HELLO on Serial0/0/0 nbr 192.168.1.102
*Jan 21 16:38:51.745: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 peerQ un/rely
0/0
R2# debug eigrp packets
EIGRP Packets debugging is on
(UPDATE, REQUEST, QUERY, REPLY, HELLO, IPXSAP, PROBE, ACK, STUB, SIAQUERY, SIAREPLY)
R2#
*Jan 21 16:38:38.321: EIGRP: received packet with MD5 authentication, key id = 2
*Jan 21 16:38:38.321: EIGRP: Received HELLO on Serial0/0/0 nbr 192.168.1.101
*Jan 21 16:38:38.321: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 peerQ un/rely
0/0
![Page 158: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/158.jpg)
Chapter 2 158 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Configuring EIGRP MD5 Authentication
Fa0/0 Fa0/0
R1 R2
172.16.1.0 /24
EIGRP AS 100
R1(config-if)# key chain R1chain
R1(config-keychain)# key 2
R1(config-keychain-key)# key-string wrongkey
R1(config-keychain-key)#
172.17.2.0 /24
S0/0/0 S0/0/0
64 kbps 192.168.1.96 /27
.101
.102
.1 .1
R2# debug eigrp packets
EIGRP Packets debugging is on
(UPDATE, REQUEST, QUERY, REPLY, HELLO, IPXSAP, PROBE, ACK, STUB, SIAQUERY, SIAREPLY)
*Jan 21 16:50:18.749: EIGRP: pkt key id = 2, authentication mismatch
*Jan 21 16:50:18.749: EIGRP: Serial0/0/0: ignored packet from 192.168.1.101, opcode = 5 (invalid
authentication)
*Jan 21 16:50:18.749: EIGRP: Dropping peer, invalid authentication
*Jan 21 16:50:18.749: EIGRP: Sending HELLO on Serial0/0/0
*Jan 21 16:50:18.749: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0
*Jan 21 16:50:18.753: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 192.168.1.101
(Serial0/0/0) is down: Auth failure
R2#
R2# show ip eigrp neighbors
IP-EIGRP neighbors for process 100
R2#
![Page 159: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/159.jpg)
Chapter 2 159 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Optimizing EIGRP Implementations
![Page 160: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/160.jpg)
Chapter 2 160 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Factors That Influence EIGRP Scalability
Cantidad de la información de enrutamiento intercambiada
entre pares: sin sumarización de ruta adecuada, esto
puede ser excesivo.
Número de routers que deben estar involucrados cuando
se produce un cambio en la topología.
Profundidad de la topología: el número de saltos que la
información debe recorrer para llegar a todos los routers.
Número de rutas alternativas a través de la red.
![Page 161: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/161.jpg)
Chapter 2 161 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Query Process (Proceso de consultas de EIGRP)
Las consultas se envían cuando se pierde una ruta y hay
un sucesor factible disponible.
La ruta perdida se encuentra en estado "active".
Las consultas se envían a todos los routers vecinos en
todas las interfaces excepto la interfaz para el sucesor.
Si los vecinos no tienen su información en ruta perdida, las
consultas se envían a sus vecinos.
Si un router tiene una ruta alternativa, que responde a la
consulta; esto detiene la consulta se extienda en esa rama
de la red.
![Page 162: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/162.jpg)
Chapter 2 162 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Overwhelming EIGRP Query Process
En grandes consultas EIGRP internetwork puede generar muchos recursos.
Existen varias soluciones para optimizar el proceso de propagación de consulta y de limitar la cantidad de carga EIGRP innecesaria en los enlaces, incluyendo :
• Summarization
• Redistribution
• EIGRP stub routing feature.
![Page 163: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/163.jpg)
Chapter 2 163 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Stuck-in-Active
Si un router no recibe una respuesta (reply) a todas las
consultas (queries) pendientes dentro 3 minutos por
defecto(180 segundos), la ruta entra en Stuck-in-Activa
(SIA) del estado.
Razones comunes de SIA:
• Un router está demasiado ocupado para responder a la consulta.
• Un router no puede asignar la memoria para procesar la consulta.
• El circuito entre los dos routers no es fiable.
• El router tiene enlaces unidireccionales..
SIA solutions:
• Rediseñar la red para limitar el intervalo de consultas por
sumarización de ruta y el comando ip summary-address eigrp.
• Configure los routers remotos como routers EIGRP stub.
![Page 164: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/164.jpg)
Chapter 2 164 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
SIA Solution: Summarization
Redes mal diseñadas pueden hacer difícil el resumen.
Resumir manualmente las rutas siempre que sea posible para apoyar a un diseño de red jerárquico.
El más redes EIGRP resume, menor será el número de consultas que se envió
• En última instancia, reduce la aparición de errores de SIA.
![Page 165: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/165.jpg)
Chapter 2 165 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
SIA Solution: Summarization
Este diseño de la red es mejor porque las direcciones de subred de las
principales redes individuales se localizan dentro de cada nube,
permitiendo rutas de resumen configuradas con el comando ip summary-
address eigrp que se inyecta al Core de la Red.
Como un beneficio adicional, las rutas de resumen actúan como un límite
para las consultas generadas por un cambio de topología.
![Page 166: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/166.jpg)
Chapter 2 166 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
SIA Solution: Stub Networks
La característica de enrutamiento EIGRP Stub
• Mejora la estabilidad de la red.
• Reduce la utilización de recursos.
• Simplifica la configuración del router remoto (spoke).
![Page 167: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/167.jpg)
Chapter 2 167 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Stub Routing
Routing Stub se utiliza comúnmente en la topología hub-
and-spoke.
Router Stub envía un paquete especial de información de
igual a todos los routers vecinos para informar sobre su
estado como un router de zona.
• Cualquier vecino que recibe un paquete para informarle sobre el
estado stub no consulta el router stub para cualquier ruta.
• Routers Stub no se consultan y en su lugar, los routers hub
conectados al router de conexión responden a la consulta en nombre
del router de zona.
Sólo los routers remotos se configuran como stubs.
![Page 168: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/168.jpg)
Chapter 2 168 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
EIGRP Stub
Configure a router as a stub router.
Router(config-router)#
eigrp stub [receive-only | connected | static | summary | redistributed]
Parameter Description
receive-only Restringe el router de compartir cualquiera de sus rutas con cualquier otro router dentro de un AS EIGRP. Palabra clave no puede combinarse con ninguna otra palabra clave.
connected
Permite la función de enrutamiento EIGRP stub para enviar las rutas conectadas. Esta opción está activada de forma predeterminada y es la opción que más se práctica stub.
static Permite la función de enrutamiento EIGRP stub enviar rutas estáticas. Redistribuir rutas estáticas con el comando redistribute static sigue siendo necesaria.
summary Permite la función de enrutamiento EIGRP stub enviar rutas resumidas de forma automática y / o resumidos de forma manual. Esta opción está activada por defecto.
redistributed Permite la función de enrutamiento EIGRP stub enviar rutas redistribuidas. Redistribución de rutas con el comando redistribute sigue siendo necesario.
![Page 169: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/169.jpg)
Chapter 2 169 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Example: EIGRP Stub Parameters
If stub connected is
configured:
• B will advertise 10.1.2.0/24 to A.
• B will not advertise 10.1.2.0/23,
10.1.3.0/23, or 10.1.4.0/24.
If stub summary is
configured:
• B will advertise 10.1.2.0/23 to A.
• B will not advertise 10.1.2.0/24,
10.1.3.0/24, or 10.1.4.0/24.
![Page 170: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/170.jpg)
Chapter 2 170 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Example: EIGRP Stub Parameters (Cont.)
If stub static is
configured:
• B will advertise 10.1.4.0/24 to A.
• B will not advertise 10.1.2.0/24,
10.1.2.0/23, or 10.1.3.0/24.
If stub receive-only is
configured:
• B won’t advertise anything to A,
so A needs to have a static
route to the networks behind B
to reach them.
![Page 171: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/171.jpg)
Chapter 2 171 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Graceful Shutdown
![Page 172: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/172.jpg)
Chapter 2 172 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Chapter 2 Summary
The chapter focused on the following topics:
Features of EIGRP, including fast convergence, use of partial updates, multiple network layer support,
use of multicast and unicast, VLSM support, seamless connectivity across all data link layer protocols
and topologies, and sophisticated metric.
EIGRP’s underlying processes and technologies—neighbor discovery/recovery mechanism, RTP,
DUAL finite state machine, and protocol-dependent modules.
EIGRP's tables—neighbor table, topology table, and routing table
EIGRP terminology:
• Advertised distance (the metric for an EIGRP neighbor router to reach the destination; the metric between the next-
hop router and the destination)
• Feasible distance (the sum of the AD from the next-hop neighbor, and the cost between the local router and the next-
hop router)
• Successor (a neighboring router that has a least-cost loop-free path to a destination, the lowest FD)
• Feasible successor (a neighboring router that has a loop-free backup path to a destination).
• Passive routes, those not undergoing recomputation; active routes, those undergoing recomputation
The five EIGRP packet types: hello, update, query, reply, and acknowledgment.
• Updates, queries, and replies are sent reliably.
![Page 173: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/173.jpg)
Chapter 2 173 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Chapter 2 Summary
• EIGRP initial route discovery process, started by a router sending hello packets.
Neighboring routers reply with update packets, which populate the router's
topology table. The router chooses the successor routes and offers them to the
routing table.
• The DUAL process including selecting FSs. To qualify as an FS, a next-hop router must have an AD less than the FD of the current successor route for the particular network, to ensure a loop-free network.
• The EIGRP metric calculation, which defaults to bandwidth (the slowest bandwidth between the source and destination) + delay (the cumulative interface delay along the path).
• Planning EIGRP implementations, including:
• IP addressing
• Network topology
• EIGRP traffic engineering.
• The list of tasks for each router in the network include:
• Enabling the EIGRP routing protocol (with the correct AS number)
• Configuring the proper network statements
• Optionally configuring the metric to appropriate interfaces.
![Page 174: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/174.jpg)
Chapter 2 174 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Chapter 2 Summary (continued)
• Basic EIGRP configuration commands.
• Commands for verifying EIGRP operation.
• Configuring a passive-interface.
• Propagating a default route.
• EIGRP summarization.
• EIGRP over Frame Relay.
• EIGRP over MPLS.
• EIGRP load-balancing
• EIGRP operation in WAN environments:
• Configuring, verifying, and troubleshooting EIGRP MD5 authentication.
• EIGRP scalability factors, including the amount of information exchanged, the number of routers, the depth of the topology, and the number of alternative paths through the network.
• The SIA state and how to limit the query range to help reduce SIAs.
• Configuring the remote routers as stub EIGRP routers.
• Graceful shutdown, which broadcasts a goodbye message (in a hello packet, with all K values set to 255) when an EIGRP routing process is shut down, to inform neighbors
![Page 175: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/175.jpg)
Chapter 2 175 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Resources
http://www.cisco.com/go/eigrp
http://www.cisco.com/en/US/customer/docs/ios/iproute_eigr
p/command/reference/ire_book.html
![Page 176: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/176.jpg)
Chapter 2 176 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public
Lab 2-1 EIGRP Configuration, Bandwidth, and
Adjacencies
Lab 2-2 EIGRP Load Balancing
Lab 2-3 EIGRP Summarization and Default Network
Advertisement
Lab 2-4 EIGRP Frame Relay Hub-and-Spoke: Router
Used as a Frame Relay Switch
Lab 2-5 EIGRP Authentication and Timers
Lab 2-6 EIGRP Challenge Lab
Lab 2-7 Troubleshooting EIGRP
Chapter 2 Labs
![Page 177: CCNP_ROUTE_v6_EIGRP](https://reader031.vdocuments.us/reader031/viewer/2022020117/563db8e8550346aa9a98197d/html5/thumbnails/177.jpg)
Chapter 2 177 © 2007 – 2012, Cisco Systems, Inc. All rights reserved. Cisco Public