ccna training » ccna configuration sim question
TRANSCRIPT
8/6/2019 CCNA Training » CCNA Configuration SIM Question
http://slidepdf.com/reader/full/ccna-training-ccna-configuration-sim-question 1/7
Type text to search here...
Home > CCNA Configuration SIM Question
CCNA Configuration SIM Question
October 19th, 2010 Go to comments
Question:
To configure the router (R2-RC) click on the console host icon that is connected to a router by a serial console cable
(shown in the diagram as a dashed black line)
CCNA Training Company recently installed a new router in their office. Complete the network installation by performing
the initial router configurations and configuring RIPV2 routing using the router command line interface (CLI) on the R2-
RC.
Name of the router is R2-RC
Enable-secret password is cisco1
The password to access user EXEC mode using the console is cisco2
The password to allow telnet access to the router is cisco3
IPV4 addresses must be configured as follows:
Ethernet network 209.165.202.128/27 – router has last assignable host address in subnet
Serial network is 192.0.2.16/28 – router has last assignable host address in the subnet. Interfaces should be enabled.
Router protocol is RIP V2
Attention :
In practical examinations, p lease note the following, the actual information will prevail.
1. Name of the router is xxx
2. Enable-secret password is xxx
3. Password to access user EXEC mode using the console is xxx4. The password to allow telnet access to the router is xxx
5. IP information
Solution:
Ads by Google CCNA Answers CCNA Practice Exam Cisco CCNA 640 802 Exam CCNA Simulator
Cisco Video Conference Guide to your telepresence solution Download it for Free Here! Cisco.com/Cisco_Telepresence
EasyEnterprise Easy EAP-TLS Network Setup Setup an EAP-TLS network in minutes www.TjlSoftware.co.uk/products.html
I passed the CCIE R&S Lab on my first attempt! Steve Clarkin - CCIE #25821 www.INE.com/CCIE
1/3/2011 CCNA Training » CCNA Configuration S…
9tut.com/59-ccna-configuration-sim-q… 1
8/6/2019 CCNA Training » CCNA Configuration SIM Question
http://slidepdf.com/reader/full/ccna-training-ccna-configuration-sim-question 2/7
1) Name the router:
Router>enable
Router#configure terminal
Router(config)#hostname R2-RC
2) Set secret password:
R2-RC(config)# enable secret cisco1
3) Set password for the console:
R2-RC(config)#line console 0
R2-RC(config-line)#password cisco2
R2-RC(config-line)#login
R2-RC(config-line)#exit
4) Set the Telnet password:
R2-RC(config)#line vty 0 4
R2-RC(config-line)#password cisco3
R2-RC(config-line)#login
R2-RC(config-line)#exit
5) Assign IP address for Ethernet interface (Fa0/0):
The Ethernet network 209.165.202.128/27 has:
Increment:32 (/27 = 255.255.255.224 or 1111 1111.1111 1111.1111 1111.1110 0000)
Network address : 209.165.202.128
Broadcast address : 209.165.202.159 (because 128 + 32 – 1 = 159)
Therefore the last assignable host address in this subnet is 209.165.202.158 and we will assign it to Fa0/0 interface with
these commands:
R2-RC(config)# interface fa0/0
R2-RC(config-if)#ip address 209.165.202.158 255.255.255.224
R2-RC(config-if)#no shutdown
R2-RC(config-if)#exit
6) Assign IP address for Serial interface (S0/0/0):
Serial network 192.0.2.16/28 has:
Increment:16 (/28 = 255.255.255.240 or 1111 1111.1111 1111.1111 1111.1111 0000)
Network address: 192.0.2.16
Broadcast address : 192.0.2.31 (because 16 + 16 – 1 = 31)
So the last assignable host address in this subnet is 192.0.2.30. Finally we assign it to s0/0/0 interface:
R2-RC(config)# interface s0/0/0
R2-RC(config-if)#ip address 192.0.2.30 255.255.255.240
R2-RC(config-if)#no shutdown
1/3/2011 CCNA Training » CCNA Configuration S…
9tut.com/59-ccna-configuration-sim-q… 2
8/6/2019 CCNA Training » CCNA Configuration SIM Question
http://slidepdf.com/reader/full/ccna-training-ccna-configuration-sim-question 3/7
R2-RC(config-if)#exit
7) Configure RIP v2 routing protocol:
R2-RC(config)#router rip
R2-RC(config-router)#version 2
R2-RC(config-router)#network 209.165.202.128
R2-RC(config-router)#network 192.0.2.16
R2-RC(config-router)#endR2-RC#copy running-config startup-config
Other lab-sims on this site:
CCNA Access List Sim
CCNA NAT SIM Question 1
CCNA NAT SIM Question 2
CCNA Frame Relay Sim
CCNA VTP SIM
CCNA EIGRP LAB
CCNA Drag and Drop SIM
CCNA Implementation SIM
Comments
1. Dark
December 8th, 2010
Forgot “no autosummary” in rip conf.
and after this configuration routers will not ping, because “clock rate” and “bandwidth” doesn’t configurate on theserial interfaces….
2. cizmo
December 9th, 2010
agree
3. kamel
December 10th, 2010
1 – In question no. 7
Virtual Routing Emulation Visually create dynamic multihop networks with free bootable CD www.candelatech.com/xorp
Pass ACCA Exams 1st Time Career Service, LSBF ACCA Tutors Team+ Fully funded MBA/MSc Degree www.CA-MB
Wireless Router Top Ten Technology Tools for Your Small Office Success! www.NotebookReview.com
1/3/2011 CCNA Training » CCNA Configuration S…
9tut.com/59-ccna-configuration-sim-q… 3
8/6/2019 CCNA Training » CCNA Configuration SIM Question
http://slidepdf.com/reader/full/ccna-training-ccna-configuration-sim-question 4/7
why : network 209.165.202.128
network 192.0.2.16
I think it must : network 209.165.202.0 , because it is a network not host
network 192.0.2.0 , because it is a network not hostIs
2- Should we write ” end ” in the end of commands?
4. Neo
December 11th, 2010
The 7th step cannot hav the following router config commands
R2-RC(config-router)#network 209.165.202.128
R2-RC(config-router)#network 192.0.2.16
b’cuz in the eigrp network commands u must enter a “classful” address which means that it must be one of the Class
A or B or C address depending on the first octet
so here as the addresses are class C addresses the network commands shud be
network 209.165.202.0
network 192.0.2.0
the answer given will be correct if the respective wildcard mask is given which are 0.0.0.127 and 0.0.0.15
respectively.
Does this convince anybody ??
9tut do u think the xplanation was sound ?? i’m jus a begginer n dis is wat i think it shud be please reply so dat i
learn.
5. Pete
December 12th, 2010
RIP v2 can carry subnet information /VLSM/,thus supporting classless inter-domain routing /CIDR/.
In that case you don’t need to use no auto-summary command.I hope this could help.
6. Neo
December 12th, 2010
small mistake in d xplanation ……but d xplanation still holds its not “eigrp” it is “Rip version 2 ″
7. rayanDecember 14th, 2010
hi 9tut
i think we should ping both router in exam..?? plz reply.. b\c there is no point off configure r2 router.. ..
8. JC
December 15th, 2010
Neo with eigrp you can have
1/3/2011 CCNA Training » CCNA Configuration S…
9tut.com/59-ccna-configuration-sim-q… 4
8/6/2019 CCNA Training » CCNA Configuration SIM Question
http://slidepdf.com/reader/full/ccna-training-ccna-configuration-sim-question 5/7
R2-RC(config-router)#network 209.165.202.128
R2-RC(config-router)#network 192.0.2.16
as your setting as long as you add this line into your eigrp
R2-RC(config-router)no auto-summary
the no auto summary makes eigrp classless
9. win
December 16th, 2010
is “no autosummary” cmd is required for rip v2…….(above question)
10. lokeswarreddy
December 16th, 2010
hi i think that there is no need of no auto summary
bcz rip will support classless
11. winDecember 16th, 2010
is 9tut simulation(9 simulation question) and mashti & acme (354) enough for exam…?
12. Qrsa
December 25th, 2010
In the cisco.com example shows, that in version 2 int valuable to use no auto-summary
13. Qrsa
December 25th, 2010
Prooflink for no auto-summary:
http://www.cisco.com/en/US/docs/ios/12_0/np1/command/reference/1rrip.html#wp1017389
http://www.cisco.com/en/US/docs/ios/12_0/np1/configuration/guide/1crip.html#wp4775
14. Curios
January 1st, 2011
Yes, i support that Rv2 requires no auto -summary bcos by default d CIDR has 2 b manual.
Also, there shud be a clock rate 4 d host 2 ping.
15. ARQ:
January 1st, 2011
this login statement
isnt this an invalid command
1. No trackbacks yet.
Add a Comment
1/3/2011 CCNA Training » CCNA Configuration S…
9tut.com/59-ccna-configuration-sim-q… 5
8/6/2019 CCNA Training » CCNA Configuration SIM Question
http://slidepdf.com/reader/full/ccna-training-ccna-configuration-sim-question 6/7
Name
Website (not required)
Submit Comment
Subscribe to comments feed
CCNA EIGRP LAB Question CCNA NAT SIM Question 1
CCNA 640-802
CCNA Lab Sim
CCNA – Access List Questions
CCNA – WANCCNA – OSPF Questions
CCNA – EIGRP Questions
DHCP Group of Four Questions
CCNA – Drag and Drop 1
CCNA – Drag and Drop 2
CCNA – Drag and Drop 3
CCNA – Drag and Drop 4
CCNA – Hotspot
CCNA – IPv6 Questions
CCNA – SubnettingCCNA – Operations 1
CCNA – Operations 2
CCNA – Operations 3
CCNA – Troubleshooting 1
CCNA – Troubleshooting 2
Share your CCNA Experience
CCNA Self-Study
Practice CCNA GNS3 Labs
CCNA Knowledge
Network Resources
CCNA FAQs & Tips
Free Router Simulators
1/3/2011 CCNA Training » CCNA Configuration S…
9tut.com/59-ccna-configuration-sim-q… 6
8/6/2019 CCNA Training » CCNA Configuration SIM Question
http://slidepdf.com/reader/full/ccna-training-ccna-configuration-sim-question 7/7
ICND1/ICND2 Website
CCNP - ROUTE Website
CCNP - SWITCH Website
CCNP - TSHOOT Website
CCNA Voice Website
CCNA Security Website
CCDA Website
CCIE Written Website
Support 9tut
Your contribution will help keep this site updated!
Top
Copyright © 2010 CCNA Training
Privacy Policy. Valid XHTML 1.1 and CSS 3.
Ads by Google
CCNA Router Lab
Cisco Router
CCNA ICND 1
Cisco Boson
1/3/2011 CCNA Training » CCNA Configuration S…
9tut.com/59-ccna-configuration-sim-q… 7