catalogue hy30-3302/uk cast-iron body gear pumps and ... fileparker hannifin pump and motor division...
TRANSCRIPT
Parker HannifinPump and Motor DivisionChemnitz, Germany
PI PGP-PGM UK.PMD RH
24
Catalogue HY30-3302/UK
Over many years Parker Hydraulics has supplied gear pumps and motors for mobile and industrial markets worldwide, especially for materials handling, commercial grass cutting and construction equipment applications. Many Parker pumps and motors have been developed and tested for the specific needs of these industries.
Parker’s defined strategy to provide engineered solutions, coupled with an award winning flexible manufacturing sys-tem, has resulted in a wide range of SAE/DIN/European and other special options being available as standard.
Characteristics
Features• Patentedinterlockingbodydesign
• 12toothgears,bronzebalanceplates
• Tandem,tripleandcross-framepumpsavailable
• Common inlets available for tandem and triplepumps
• Continuousoperatingpressuresupto310bar
• Productionrun-inavailabletosuiteOEMapplicationconditions and to provide optimized volumetric efficiencies
• Pressurebalanceddesignforhighefficiency
• Reduced system noise levels compared to earliermodels
• Highpowerthrough-drivecapability
• Widerangeofintegralvalvesforpowersteering,powerbrakes, fan drivers and implement hydraulics
• Loadsenseandsolenoidoperatedunloadingvalves
• Lownoiseversionas“stealth“pump
Cast-Iron Body Gear Pumps and MotorsSeries PGP/PGM600
Pump type Heavy-duty, cast iron, external gear.
Mounting SAE, rectangular, thru-bolt standard specials on request.
Ports SAE and metric split flanges and othersShaft style SAE splined, keyed, tapered, cylindrical tang drive, specials on request.
Speed 500 - 3500 rpm, see Technical Data
Theor. displacement See Technical Data
Drive Drive direct with flexible coupling is recommended.
Axial / Radial load Units subject to axial or radial loads must be specified with an outboard bearing.
Inlet pressure Operating range 0.8 to 2 bar abs. Min. inlet pressure 0.5 bar abs. Short time without load. Consultation is recommended.
Outlet pressure See Technical Data
Pressure rising rate Max. 3000 bar/s
Flow velocity See Nomograph for Pipe Velocity
Hydraulic fluids Hydraulic oil HLP, DIN 51524-2 Fluid temperature Range of operating temperature -15 to +80 °C.
Max. permissible operating pressure dependent on fluid temperature. Temperature for cold start -20 to -15 °C at speed ≤ 1500 rpm. Max. permissible operating pressure dependent on fluid temperature.
Fluid viscosity Range of operating viscosity 8 to 1000 mm²/s. Max. permissible operating pressure dependent on viscosity.
Viscosity range for cold start 1000 to 2000 mm²/s at operating pressure p≤10 bar and speed n ≤1500 rpm. Range of ambient temperature -40 °C to +70 °C
Filtration According to ISO 4406 Cl. 18/16/13
Direction of rotation Clockwise, counter-clockwise or double. (looking at the Attention! Drive pump only in drive shaft) indicated direction of rotation.
Multiplepump •Availableintwoorthreesection assemblies configuration. •Max.shaftloadmustbeconformto the limitations shown in the shaft loading rating table in this catalogue. •Max.loadisdeterminedbyadding the torque values for each pumping section that will be simultaneously loaded. Separate or common Separate inlet configuration:inletcapability •Eachgearhousinghasindividualinlet and outlet ports. Common inlet configuration: •Twogearsetsshareacommoninlet.
Technical data
Parker HannifinPump and Motor DivisionChemnitz, Germany
PI PGP-PGM UK.PMD RH
25
Catalogue HY30-3302/UK
Port options (pumps)
1"-11 BSP thread/ 3/4"-14 BSP thread
rec. from 14 ccm to 26 ccm
1¼"-11 BSP thread/ 3/4"-14 BSP thread
rec. from 29 ccm to 41 ccm
1½"-11 BSP thread/ 1"-11 BSP thread/
rec. from 41 ccm to 52 ccm
1"-M10 SAE metric flange 3/4"-M10 SAE metric flange rec. from 16 ccm to 23 ccm
1¼"-M10 SAE metric flange 1"-M10 SAE metric flange rec. from 26 ccm to 41 ccm
1½"-M12 SAE metric flange 1"-M10 SAE metric flange rec. from 41 ccm to 52 ccm
Code
E6E5
E7E5
E8E6
T3T2
T4T3
T5T3
1) Code of drain line for PGM620 only. 2 Options: G4 = 1/4-19 BSP rear drain. B1 = no drain, unit code must be “B“ or “C“.
PGGear
designShaftType Shaft
sealUnit Dis-
place-ment
Code
PumpMotor
PM
Type
Rotation
Code
ClockwiseCounter- clock-
wiseBi-directional
CA
B
Rotation
Code ccm
0160 16.0 0190 19.0 0210 21.0 0230 23.0 0260 26.0 0290 29.0 0330 33.0 0360 36.0 0370 37.0 0410 41.0 0440 44.0 0460 46.0 0500 50.0 0520 52.0
Displacement
Code
Single unitA
Unit
Flange
2) Only used with flange H2, H3.3) Only used with flange D7.
620
Pump Motor
Standard motor with drain port
Standard motor w. two checks
Standard motor w. one anti-
cavitation check (ACC)
Multiple unit
—
B
C
Example: T4 = inlet port T3 = outlet port
B 1 B 1
side portsoption
No rear ports(rear ports on request)
Inlet Outlet
1)
Flange
98.4x128.2 - Ø50.77 rectangular
106.4 - Ø82.55 SAE ”A” 2bolt flange
146.1 - Ø101.06 SAE ”B” 2bolt flange
114.5 x 114.5 - Ø127 SAE ”C” 4bolt square
Code
D7
H2
H3
A4
E5E5
E6E6
E7E7
3/4"-14 BSP thread 3/4"-14 BSP thread
rec. from 16 ccm to 26 ccm
1" - 11 BSP thread/ 1" - 11 BSP thread
rec. from 29 ccm to 41 ccm
1¼"-11 BSP thread/ 1¼"-11 BSP thread
rec. from 41 ccm to 52 ccm
Port options (motors)Code
Shaft
13T, 16/32DP, 41.2L, SAE ”B” spline
15T, 16/32DP, 46L, SAE “B-B” spline
Ø21.59, 11.2L, 4.0key, M14x1.5, taper 1:8
Code
D1 2)
E1
T1 3)
Code
No seal
NBR (2 bar)
FPM (5 bar)
X
N
V4)
Shaft seal
4) for motors recommended
Ordering CodeCast-Iron Body Gear Pumps and MotorsSeries PGP/PGM620
Parker HannifinPump and Motor DivisionChemnitz, Germany
PI PGP-PGM UK.PMD RH
26
Catalogue HY30-3302/UK
30
28
26
24
22
20
18
16
14
12
10
8
6
4
2
00 50 100 150 200 250 300
0
4
8
12
16
20
24
28
32
36
40
44
48
52
56
60
65
60
55
50
45
40
35
30
25
20
15
10
5
00 50 100 150 200 250 300
0
10
20
30
40
50
60
70
80
90
100
110
120
130
PGP620 - 16.0 CC PGP620 - 26.0 CC
PGP620 - 41.0 CC PGP620 - 52.0 CC
0 50 100 150 200 250 300
65
75
60
70
80
55
50
45
40
35
30
25
20
15
10
5
0 0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
0 50 100 150 200 250 300
65
75
60
70
80
55
50
45
40
35
30
25
20
15
10
5
0 0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
Performance Curves
Fluid temperature: 45 °C± 2K ; Viscosity: 36mm2/s ; Inlet pressure: 0.9 + 0.1 bar absolute
Cast-Iron Body Gear Pumps and MotorsSeries PGP620
Pressure [bar]
Pressure [bar]
Pressure [bar]
Pressure [bar]
Flo
w [l
/min
.]F
low
[l/m
in.]
Flo
w [l
/min
.]F
low
[l/m
in.]
Inpu
t Pow
er [k
W]
Inpu
t Pow
er [k
W]
Inpu
t Pow
er [k
W]
Inpu
t Pow
er [k
W]
Flow at n=3500 rpm
Flow at n=3500 rpm
Flow at n=3500 rpm
Flow at n=3500 rpm
Flow at n=1500 rpm
Flow at n=1500 rpm
Flow at n=1500 rpm
Flow at n=1500 rpm
Flow at n=500 rpm
Flow at n=500 rpm
Flow at n=500 rpm
Flow at n=500 rpm
I. Power at n=3500 rpm
I. Power at n=3500 rpm
I. Power at n=3500 rpm
I. Power at n=3500 rpm
I. Power at n=1500 rpm
I. Power at n=1500 rpm
I. Power at n=1500 rpm
I. Power at n=1500 rpm
I. Power at n=500 rpm
I. Power at n=500 rpm
I. Power at n=500 rpm
I. Power at n=500 rpm
Parker HannifinPump and Motor DivisionChemnitz, Germany
PI PGP-PGM UK.PMD RH
27
Catalogue HY30-3302/UK
XXXX cm3/rev A B SS G PP G min. rpm max. rpm max. bar clockwise counter-clockwise
0160 16.0 79.2 122.7 E6 1"-11 E5 ¾"-14 500 3000 275 702 9111 052 702 9112 053
0190 19.0 82.5 126.0 E6 1"-11 E5 ¾"-14 500 3000 275 702 9111 186
0210 21.0 84.7 128.2 E6 1"-11 E5 ¾"-14 500 3000 275 702 9111 168
0230 23.0 86.9 130.4 E6 1"-11 E5 ¾"-14 500 2700 275 702 9111 098 702 9112 054
0260 26.0 90.2 133.7 E6 1"-11 E5 ¾"-14 500 2400 275 702 9111 112 702 9112 093
0290 29.0 93.5 137.0 E7 1¼"-11 E5 ¾"-14 500 3000 275
0330 33.0 97.9 141.4 E7 1¼"-11 E5 ¾"-14 500 3000 275
0360 36.0 101.2 144.7 E7 1¼"-11 E5 ¾"-14 500 2900 250
0370 37.0 102.3 145.8 E7 1¼"-11 E5 ¾"-14 500 2900 250 702 9111 164 702 9112 046
0410 41.0 106.7 150.2 E7 1¼"-11 E5 ¾"-14 500 2600 220 702 9112 071
0440 44.0 110.0 153.5 E8 1½"-11 E6 1"-11 500 3000 210 702 9112 105
0460 46.0 112.2 155.7 E8 1½"-11 E6 1"-11 500 3000 210
0500 50.0 116.6 160.1 E8 1½"-11 E6 1"-11 500 3000 210
0520 52.0 118.8 162.3 E8 1½"-11 E6 1"-11 500 3000 210 702 9112 104
Displacement Dimension Inlet port Outlet port Speed of Working Order number rotation pressure direction of rotation
Technical Data / Dimensions
PGP620 A XXXX Y D1 H3 N SS PP B1 B1
Dimensions (clockwise rotation shown)
“Y” = C (clockwise rotation) = A (counter-clockwise rotation)
Cast-Iron Body Gear Pumps and MotorsSeries PGP620
...
...
20.3
142
A
5.1
55.8
B41.2
14.0
Ø10
1.6
-0.0
5
67.0
67.0
25.7
33.3
Ø18
.3
G
73.0
2 x Ø14.3
146.0
176
60.5
E
Inlet
Outlet
SAE “B” spline13 teeth 16/32 DPflat root side fit
Parker HannifinPump and Motor DivisionChemnitz, Germany
PI PGP-PGM UK.PMD RH
28
Catalogue HY30-3302/UK
XXXX cm3/ A B SS d G H W SS d G H W min. max. max. bar clockwise counter- rev rpm rpm clockw.
0160 16 79.2 122.7 T3 1" M10 52.37 26.19 T2 ¾" M10 47.63 22.23 500 1500 275 0190 19 82.5 126.0 T3 1" M10 52.37 26.19 T2 ¾" M10 47.63 22.23 500 2300 275 702 9112 062 0210 21 84.7 128.2 T3 1" M10 52.37 26.19 T2 ¾" M10 47.63 22.23 500 2000 275 0230 23 86.9 130.4 T3 1" M10 52.37 26.19 T2 ¾" M10 47.63 22.23 500 1900 275 0260 26 90.2 133.7 T4 1¼" M10 58.72 30.17 T3 1" M10 52.37 26.19 500 1600 275 0290 29 93.5 137.0 T4 1¼" M10 58.72 30.17 T3 1" M10 52.37 26.19 500 3000 275 702 9111 151 0330 33 97.9 141.4 T4 1¼" M10 58.72 30.17 T3 1" M10 52.37 26.19 500 2600 275 702 9111 087 702 9112 070 0360 36 101.2 144.7 T4 1¼" M10 58.72 30.17 T3 1" M10 52.37 26.19 500 2400 250 0370 37 102.3 145.8 T4 1¼" M10 58.72 30.17 T3 1" M10 52.37 26.19 500 2300 250 0410 41 106.7 150.2 T5 1½" M12 69.82 35.71 T3 1" M10 52.37 26.19 500 2100 220 702 9111 179 702 9112 117 0440 44 110.0 153.5 T5 1½" M12 69.82 35.71 T3 1" M10 52.37 26.19 500 2000 210 702 9112 037 0460 46 112.2 155.7 T5 1½" M12 69.82 35.71 T3 1" M10 52.37 26.19 500 1900 210 702 9111 117 0500 50 116.6 160.1 T5 1½" M12 69.82 35.71 T3 1" M10 52.37 26.19 500 1700 210 702 9111 150 0520 52 118.8 162.3 T5 1½" M12 69.82 35.71 T3 1" M10 52.37 26.19 500 1700 210 702 9112 022
Displace- Dimension Inlet port Outlet port Speed of Working Order number ment rotation pressure direction of rotation
Technical Data / Dimensions
PGP620 A XXXX Y T1 D7 N SS PP B1 B1
Dimensions (clockwise rotation shown)
“Y” = C (clockwise rotation) = A (counter-clockwise rotation)
Cast-Iron Body Gear Pumps and MotorsSeries PGP620
...
...
25.7
33.3
Ø18
.3
67.0
67.0
146.0
176
2 x Ø14.3
60.5
20.3
14.0
A
5.1
55.8
B41.2
Ø10
1.6
-0.0
5
Ød H
142
73.0
G
W
E
Inlet
Outlet
SAE “B” spline13 teeth 16/32 DPflat root side fit
Parker HannifinPump and Motor DivisionChemnitz, Germany
PI PGP-PGM UK.PMD RH
29
Catalogue HY30-3302/UK
PG
Geardesign
ShaftType Shaft seal
Unit Dis-place-ment
Code
PumpMotor
PM
Type
Rotation
Code ccm
0300 30.0 0350 35.0 0400 40.0 0450 45.0 0500 50.0 0550 55.0 0600 60.0 0650 65.0 0700 70.0 0750 75.0 0800 80.0
Displacement
Flange
2) Only used with flange A3, H3.3) Only used with flange A4, K3.
640
Example: T5 = inlet port T3 = outlet port
B 1 B 1
side portsoption
No rear ports(rear ports on request)
Inlet Outlet
Flange
89.8x89.8 - Ø101.06 4 bolt square flange
114.5x114.5 - Ø127 SAE ”C” 4 bolt square flange
146.1 - Ø101.06 SAE ”B” 2 bolt flange
181.0 - Ø127 SAE ”C” 2 bolt flange
Code
A3
A4
H3
K3
Shaft
13T, 16/32DP, 41.2L, SAE ”B” spline
15T, 16/32DP, 46.0L, SAE ”B-B” spline
14T, 12/24DP, 55.6L, SAE ”C” spline
Code
D1 2)
E1 2)
E4 3)
Code
No seal
NBR
FPM
PTFE (motors only)
X
N
V
T
Shaft seal
Ordering Code
Port options (pumps)
1½" -11 BSP Thread / 1¼" -11 BSP Thread
rec. from 30 ccm to 50 ccm
1¼" - M10 SAE metr. split flange 1“ - M10 SAE split flange
rec. from 30 ccm to 40 ccm
1½" - M12 SAE metr. split flange 1“ - M10 SAE split flange
rec. from 45 ccm to 60 ccm
2" - M12 SAE metr. split flange 1¼" - M10 SAE metr. split flange
rec. from 65 ccm to 80 ccm
Code
E8E7
T4T3
T5T3
T6T4
Cast-Iron Body Gear Pumps and MotorsSeries PGP/PGM640
Code
Single unitA
UnitPump Motor
Standard motor with drain port
Standard motor w. two checks
Standard motor w. one anti-
cavitation check (ACC)
Multiple unit
—
B
C
Code
ClockwiseCounter- clock-
wiseBi-directional
CA
B
Rotation
1)
1) Code of drain line for PGM640 only. 2 Options: G4 = 1/4"-19 BSP rear drain. B1 = no drain, unit code must be “B“ or “C“.
E7E7 1¼"-11 BSP thread/ 1¼"-11 BSP thread
Port options (motors)Code
Parker HannifinPump and Motor DivisionChemnitz, Germany
PI PGP-PGM UK.PMD RH
30
Catalogue HY30-3302/UK
PGP640 - 30.0 CC PGP640 - 50.0 CC
PGP640 - 65.0 CC PGP640 - 80.0 CC
Performance Curves
Fluid temperature: 45 °C± 2K ; Viscosity: 36mm2/s ; Inlet pressure: 0.9 + 0.1 bar absolute
Cast-Iron Body Gear Pumps and MotorsSeries PGP640
65
60
55
50
45
40
35
30
25
20
15
10
5
00 50 100 150 200 250 300
0
10
20
30
40
50
60
70
80
90
100
110
120
130
0 50 100 150 200 250 300
65
75
60
70
80
55
50
45
40
35
30
25
20
15
10
5
0 0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
0 50 100 150 200 250 3000
10
20
30
40
50
60
70
80
90
100
110
120
130
0
20
40
60
80
100
120
140
160
180
200
220
240
260
0 50 100 150 200 250 3000
10
20
30
40
50
60
70
80
90
100
110
120
130
0
20
40
60
80
100
120
140
160
180
200
220
240
260
Pressure [bar]
Pressure [bar]
Pressure [bar]
Pressure [bar]
Flo
w [l
/min
.]F
low
[l/m
in.]
Flo
w [l
/min
.]F
low
[l/m
in.]
Inpu
t Pow
er [k
W]
Inpu
t Pow
er [k
W]
Inpu
t Pow
er [k
W]
Inpu
t Pow
er [k
W]
Flow at n=3000 rpm
Flow at n=3000 rpm
Flow at n=3000 rpm
Flow at n=3000 rpm
Flow at n=1500 rpm
Flow at n=1500 rpm
Flow at n=1500 rpm
Flow at n=1500 rpm
Flow at n=500 rpm
Flow at n=500 rpm
Flow at n=500 rpm
Flow at n=500 rpm
I. Power at n=3000 rpm
I. Power at n=3000 rpm
I. Power at n=3000 rpm
I. Power at n=3000 rpm
I. Power at n=1500 rpm
I. Power at n=1500 rpm
I. Power at n=1500 rpm
I. Power at n=1500 rpm
I. Power at n=500 rpm
I. Power at n=500 rpm
I. Power at n=500 rpm
I. Power at n=500 rpm
Parker HannifinPump and Motor DivisionChemnitz, Germany
PI PGP-PGM UK.PMD RH
31
Catalogue HY30-3302/UK
XXXX cm3/ A B SS d G H W PP d G H W min. max. max. clockwise counter- rev rpm rpm bar clockwise
0300 30 128.6 176.1 T4 1-¼" M10 58.72 30.17 T3 1" M10 52.37 26.19 500 3000 310
0350 35 128.6 176.1 T4 1-¼" M10 58.72 30.17 T3 1" M10 52.37 26.19 500 3000 310
0400 40 131.8 182.7 T4 1-¼" M10 58.72 30.17 T3 1" M10 52.37 26.19 500 3000 310 704 9111 055 704 9112 020
0450 45 131.8 182.7 T5 1-½" M12 69.82 35.71 T3 1" M10 52.37 26.19 500 3000 310
0500 50 135.6 189.3 T5 1-½" M12 69.82 35.71 T3 1" M10 52.37 26.19 500 3000 310 704 9111 016
0550 55 135.6 189.3 T5 1-½" M12 69.82 35.71 T3 1" M10 52.37 26.19 500 3000 310 704 9111 050 704 9112 019
0600 60 138.4 195.8 T5 1-½” M12 69.82 35.71 T3 1" M10 52.37 26.19 500 3000 290 704 9111 059
0650 65 138.4 195.8 T6 2" M12 77.77 42.88 T4 1-¼" M10 58.72 30.17 500 3000 265 704 9111 040 704 9112 022
0700 70 142.2 203.2 T6 2" M12 77.77 42.88 T4 1-¼" M10 58.72 30.17 500 3000 245
0750 75 142.2 203.2 T6 2" M12 77.77 42.88 T4 1-¼" M10 58.72 30.17 500 3000 225
0800 80 142.2 203.2 T6 2" M12 77.77 42.88 T4 1-¼" M10 58.72 30.17 500 3000 210 704 9111 045
Displace- Dimension Inlet port Outlet port Speed of Working Order number ment rotation pressure direction of rotation
Technical Data / Dimensions
PGP640 A XXXX Y D1 H3 N SS PP B1 B1
Dimensions (clockwise rotation shown)
“Y” = C (clockwise rotation) = A (counter-clockwise rotation)
Cast-Iron Body Gear Pumps and MotorsSeries PGP640
85.1
W
60
25.4
Ød H
146.0
G
42.6
80.0
80.0
73.0
174
2 x Ø14.1
B
A
171
41.2
Ø10
1.6
-0.0
5
15.8
9.4
33.3 full spline
SAE “B” spline13 teeth 16/32 DPflat root side fit
E
Inlet
Outlet
Parker HannifinPump and Motor DivisionChemnitz, Germany
PI PGP-PGM UK.PMD RH
32
Catalogue HY30-3302/UKOrdering Example
PGP
Shaft code Shaft sealfront unit
Displacement
Rotation Flange code
620
Outlet side port
Inlet side port
0330
see single unit
C D1 H3 N T4 T3 S
B = Multiple pump
N = Multiple distributor pump
Product type
B
S = Separate inlets
C = Common inlet (For common inlet, the other (second) inlet port must be coded B1.)
Section connection
–
Inlet side port
Displacement
Shaft sealbetween sect.
Outlet side port
620
Outlet rear port
Inlet rear port
0260 X T4 T3 B1 B1A
Product type 1)
1) Further B possible for triple units
Code for multiple units
This coding system can be used for all pumps series 600.
Cast-Iron Body Gear Pumps and MotorsSeries PGP600
Parker HannifinPump and Motor DivisionChemnitz, Germany
PI PGP-PGM UK.PMD RH
33
Catalogue HY30-3302/UKSplit Gear Pumps
Quality paysAluminium or cast-iron bodied ’split-gear‘ gear pumps are designed for high pressure and speed ratings together with high efficiency and optimised noise levels.
Series PGP511 / PGP620 (on request)• Upto250barconstantoperationpossibledueto
high-quality materials• Lownoiselevelseveninconstantoperation• Highefficiencythankstoprecisemanufacturing• Completeproductrangeforhugevarietyof applications• Commoninletportsfordoubleandtriplepumps• Widechoiceofintegratedvalves,e.g.load-sensing
and solenoid types• Fullrangeofprovenmotorsavailable
The flow pulsation is considerably decreased by phased dual element gear sets, resulting in models with clearly lower noise levels. Common inlet available for multiple section units.
Gear Pumps and MotorsSeries PGP
Parker HannifinPump and Motor DivisionChemnitz, Germany
PI PGP-PGM UK.PMD RH
34
Catalogue HY30-3302/UKNomograph
Gear Pumps and MotorsSeries PGP/PGM
1000900
800700
600
500
300
200
150
10090
70
702.50
2.50
3.00
4.00
5.00
6.007.00
8.009.00
10.00
15.00
20.00
30.00
40.00
50.00
0.15
0.10
0.20
0.30
0.40
0.50
0.600.70
0.800.90
1.002.00
2.00
1.50
1.50
1.20
1.25
1.00
0.75
0.50
HFB, HFC
HFB, HFC
60
60
50
40
40
20
15
109
8
5
4
2
3 400 Q [l/min]v [m/s]
d [mm] =
67
10
15
20
30
30
50
80
400
6π
Nomograph for Pipe Velocity
FlowQ [l/min]
Inside Pipe Diameterd [mm/inch]
Flow Velocityv [m/s]
Maximun recommendedvelocity for
Inlet
Tank Return
Outlet
Oil
Oil
Parker HannifinPump and Motor DivisionChemnitz, Germany
PI PGP-PGM UK.PMD RH
35
Catalogue HY30-3302/UKShaft Loads / Fluids
Shaft loads PGP/PGM600
Shaft loads PGP/PGM500
Code Description Type Torque rating 620 [Nm] Torque rating 640 [Nm]
D1 13T, 16/32 DP, 41.2L, SAE ”B” splined 272 328
E1 15T, 16/32 DP, 46.0L, SAE ”B-B” splined 460 503
E4 14T, 12/24 DP, 5.6L, SAE ”C” splined — 960
T1 Ø21.59, 11.2L, 4.0key, M14x1.5 tapered 1:8 218 —
Connecting shaft for multiple units 228 407
Hydraulic fluids
Type Fluid composition Max. working pressure [bar] Max. speed [min-1] Temperature Seal
Hydraulic fluid Mineral oil based on See Technical Data See Technical Data -15 ... +80°C NBR hydraulic fluid acc. to ISO/DIN -15 ... +120°C FPM
HFB Water-in-oil emulsion 40/60 140 1500 +2 ... +65°C NBR
HFC Water-glycol 40/60 140 1500 -15 ... +65°C NBR
HFD Phosphate ester 140 1500 -10 ... +80°C FPM
Shaft loads PGP/PGM500 Code Description Type Torque rating [Nm]
PGP/PGM503 PGP/PGM505 PGP/PGM511 PGP/PGM517
H1 Ø10.0, 3.0 key, no thread, 36L parallel 30 — — —
P2 Ø9.95, 8.8L, 2.4 key, M6 taper 1:8 30 — — —
V1 5 x 6.5 long shaft w/o coupling tang drive 20 — — —
V2 5 x 4.5 short shaft w/o coupling tang drive 20 — — —
A1 9T, 16/32DP, 32L, SAE ”A” splined — 108 — —
J1 Ø12.7, 3.2 key, no thread, 38L parallel — 43 — —
K1 Ø15.88, 4.0 key, no thread, 32L, SAE ”A” parallel — 85 — —
Q2 Ø14.25, 5.5L, 3.0 key, M10x1 taper 1:8 — 68 — —
A1 9T, 16/32DP, 32L, SAE ”A” splined — — 86 —
C1 11T, 16/32DP, 38.2L, SAE 19-4 splined — — 184 —
F1 9T, B17x14.23L, DIN 5482 splined — — 101 —
K1 Ø15.88, 4.0 key, no thread, 32L, SAE ”A” parallel — — 75 —
L6 Ø19.05, 4.8 key, no thread, 32L, SAE 19-1 parallel — — 145 —
S1 Ø17.0, 7.7L, 3.0 key, M12x1.5 taper 1:5 — — 193 —
S2 Ø16.65, 12.0L, 3.2 key, M12x1.5 taper 1:8 — — 198 —
S4 Ø16.65, 12.0L, 4.0 key, M12x1.5 taper 1:8 — — 198 —
D1 13T, 16/32DP, 41.2L, SAE ”B” splined — — — 345
M1 Ø22.2, 6.3 key, no thread, 41.2L, SAE ”B” parallel — — — 251
M2 Ø25.4, 6.3 key, no thread, 46L, SAE ”B-B” parallel — — — 395
T1 Ø21.59, 11.2L, 4.0 key, M14x1.5 taper 1:8 — — — 250
Connecting shaft for multiple units 20 36 110 228
Formula to calculate shaft load
Flanges for suction and discharge portsPlease refer to Parker Bulletin 4040/UK.
Gear Pumps and MotorsSeries PGP/PGM