catalogue 2013 - integrated · pdf filecatalogue 2013. index air con service equipment.....1...
TRANSCRIPT
INTEGRATED MARKETING (PTY) LTD
Unit10, Keymax Industrial Park
1006 Ergon street
Lyttelton Ext 6
Tel: 012 664 3556
Fax: 086 568 8466
E-mail: [email protected]
VAT No: 4040202949 Co. Reg No. 1982/011003/07
CATALOGUE 2013
INDEX
AIR CON SERVICE EQUIPMENT.....................................................1AUXILIARY JACKS...........................................................................1 AIR COMPRESSOR.......................................................................22BEAD BLASTER..............................................................................2BEAD BREAKER.............................................................................2BEAD KNOCKER............................................................................2BOTTLE JACKS...............................................................................2BRAKE DISC SKIMMER..................................................................3COIL SPRING COMPRESSOR..........................................................4ENGINE CRANE.............................................................................4 ENGINE STAND..............................................................................5EXHAUST PIPE BENDER................................................................4GEARBOX JACK..............................................................................5HEADLIGHT AIMER ......................................................................5HYDRAULIC PUMP .......................................................................5HYDRAULIC RAM KIT .................................................................21IMPACT WRENCH 1” ....................................................................5LIFT – ONE SIDE .........................................................................21LIFT – TWO POST ......................................................................6-7LIFT – FOUR POST ........................................................................7LIFT – LOW LEVEL ........................................................................8LIFT – MID RISE ............................................................................8LIFT – MOTORCYCLE ...................................................................9LIFT –WHEEL ALIGNMENT ...........................................................9LIFT – SCISSORS ALIGNMENT ......................................................9NITROGEN EQUIPMENT ............................................................10PORTA POWER ...........................................................................11PRESS – HYDRAULIC ...................................................................11PRESS – ELECTRO HYDRAULIC....................................................11PRESS – PNEUMATIC ..................................................................11PRESSURE CLEANER ...................................................................17RIM REPAIR EQUIPMENT ...........................................................12SHOCK ABSORBER TESTER .........................................................20TOOL TROLLEY ...........................................................................13TRESTLES ....................................................................................14TROLLEY JACKS ...........................................................................14TYRE CHANGING TOOLS ............................................................15TYRE INFLATORS.........................................................................20TURN TABLES .............................................................................15TYRE CHANGERS ...................................................................15-16TYRE SPREADER .........................................................................17TYRE VULCANISER......................................................................17WELDER......................................................................................17WHEEL ALIGNMENT EQUIPMENT .............................................20WHEEL BALANCER.................................................................18-19WHEEL DOLLY ............................................................................21
Zell AC1000-3G Air-Con Service Station
AC1000-3G Specification & ConfigurationRefrigerant R134a
Operating Temperature 5 – 50 o C
Max pressure 18 bar
Power Supply 220v, 50Hz
Weight 95kg
Packing Size 50 x 70 x 107cm
HP/LP Gauge 80mm/class 1.0
Tank Gauge 40mm
LCD back lit 192 x 64 dot
HP/LP hoses 250cm / SAE-JS2196
Compressor 3/8hp, 14cc
Fan/ condenser Yes
Filter Drier 80kg
Vacuum Pump 120L/min, 4.2cfm
PAG bottle 250ml
Electronic Scale 1g / 30kg
R134a refrigerant
Zell AC1000-HFO Air-Con Service Station
HFO - R1234yf refrigerant
AC1000-HFO Specification & ConfigurationRefrigerant HFO-R1234yf
Operating Temperature 5 – 50 o C
Max pressure 18 bar
Power Supply 220v, 50Hz
Weight 95kg
Packing Size 50 x 70 x 107cm
HP/LP Gauge 80mm/class 1.0
Tank Gauge 40mm
LCD back lit 192 x 64 dot
HP/LP hoses 250cm / SAE-JS2196
Compressor 3/8hp, 14cc
Fan/ condenser Yes
Filter Drier 80kg
Vacuum Pump 120L/min, 4.2cfm
Tank 14.5 L
PAG bottle 250ml
Electronic Scale 1g / 30kg
IM-C/Jack- Auxiliary jack with hand pump
IM-6006- Auxiliary jack & cradle support 3 ton capacity - Air operated
Page 1
IM-6006- Auxiliary jack & cradle3 ton capacity - Air operated
IM-RJ 6 Auxiliary
Rolling Jack
Input pressure: 8 bar /120psi
Operating pressure: 6 - 8 bar / 87-116psi
Max. pressure: 10 bar / 145Psi
Rapid tyre inflation, after tyre fitting. Equipped with automatic
purge of over limit pressure., Supplied with Pressure Gauge
IM-BB-05IM-BB-10
Weight: 11kgDimension: 400x450x360mm
Weight: 15kgDimension: 600x480x360mm
IM- BB Bead BlasterIM- BBR Bead Knocker / Stamper
Y471130 – To be used on 5 piece rims 25” – 51”.
With pry bar / bead loosening pockets. G.W.14
OTR Bead Breaker for 5 piece rims
Universal Bead Breaker for 3 piece rims
Y471120 – Works on most single, two and three
piece rims
Pneumatic Bead Breaker - PAX ring remover
These professional bottle jacks meet the highest standards. All models have a chrome main ram and chrome pump piston. The
extension screws have a pressed tread. These units can be used horizontally and vertically.
Model Capacity Min
Height
Lifting
Height
Adj.
Height
Max
Height
N.W
Y410200 2 Ton 158 90 60 308 2.3
Y410400 4 Ton 180 110 60 350 3.3
Y410600 6 Ton 197 125 60 382 4.4
Y411200 12 Ton 214 125 60 399 7.2
Y412000 20 Ton 244 145 60 449 10.5
Y413000 30 Ton 285 180 0 465 14.6
Hydraulic Bottle Jacks
Page 2
IM- AA202D On car brake disc lathe
Maximum brake disc thickness 40mm
Adjustment knob accuracy ≤0.02mm -≤0.01mm
Feed rate 8.5mm/min
Electrical specifications 220V / 110V
Net weight 11kg
415 x 295
Drive Unit:
Working height min / max 1 / 1.20m
Drive speed 98rpm
Electrical specifications 220V / 110V
Weight 68kg
Ambient temperature range -20℃ to 40℃Year of construction show on information plate
Turning accuracy ≤ 0.005mm
Brake disc run out ≤ 0.005mm
Brake disc thickness variation 0.005 – 0.01mm
Brake disc surface roughness Ra 1.5 – 2.0um
Standard parts for BL-202D
IM- OTCL450A On car brake disc lathe
Maximum rotor turning diameter 360mm
Maximum Rotor Thickness 51mm
Maximum Rotor friction Surface Area 76mm
Feed Distance 110mm
Spindle Revolutions Variable Speed 30-120 RPM
Motor Power 1.5HP (1.1kw) @ 3450rpm
Electric Power AC220v 50/60Hz 15A
IM- C9350 Off car brake disc lathe
Spindle Travel 175mm
Spindle Speed 70, 80, 118 RPM
Min Spindle Feed Speed 0.05 mm per revolution
Max Spindle Feed Speed 0.50mm per revolution
Min Cross Feed Speed 0.05 mm per revolution
Max Cross Feed Speed 0.50 mm per revolution
Hand wheel Graduations 0.05mm
Rotor Diameter 180mm – 381mm
Rotor Thickness 48mm
Drum Diameter 152mm – 711mm
Drum Depth 175mm
Motor 1PH 220v 50/60 Hz / 3PH 380v 50/60Hz
Weight 200kg
Dimensions 970 x 920 x 1140mm
Drum Diameter 180-350mm
Slide Travel 100mm
Rotational Speed of spindle 60, 90 RPM
Feed 0.15mm per revolution
Motor Power 0.75Kw
Overall Dimensions 695mm x 565mmx 635mm
Packing Dimensions 710mm x 750mm x 730mm
Nett Weight 200kg
Gross Weight 230kg
IM- C9335B Off car brake disc / drum lathe
Page 3
IM- SD1201A Coil Spring Compressor
Capacity: 1Ton
Max. working length: 240mm
Ram travel: 240mm
Spring size: 4~6-1/2 inch
N.W.: 19.5kgs
G.W.: 20.5kgs
Package Size:650x265x165mm
Capacity: 1Ton
Max. working length: 450mm
Ram travel: 420mm
Spring size: 4~6-1/2 inch
Air pressure: 0.65-0.9MPa
N.W.: 63kgs
G.W.: 67kgs
Package Size:140.5x54.5x29cm
IM- SD1206 Coil Spring Compressor
Specifications
Maximum Load : 1500
Upper Yoke positions: 7
Lower Yoke Travel: 340mm
Spring Diameter: 102 – 160mm
Foot operated air hydraulic unit
IM- SD1205 Coil Spring Compressor
IM- AA0601D Hydraulic Engine Crane 3 ton
Rated loading capacity 3 ton
Maximum Height 2200 mm
G.W. 113kg
N.W. 118kg
Packing size 1130 x 810 x 110mm
1420 x 310 x 210mm
730 x 200 x 190mm
This 1 ton foldable crane constructed from heavy-gauge,
welded square tubular steel, includes the following
features: *Hold-to-run control safety system *Nylon
wheels *Ram and pump are combined into one unit to
eliminate hose and / or connections *4 positions to
secure arm *chrome ram * Rear wheels rotate 360
degrees *Safety feet at base to support stability when
crane is folded up.
*Max lifting height 1940mm *Min lifting
height 300mm
Page 4
•Maximum bending radius: 5" / 127 mm
•Minimum bending radius: 3-1/3" / 89 mm
•Maximum tube capacity: 3" / 76 mm / .095 wall
•Standard die pack (BB-1): 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2"
•Top cylinder working force: 60,000 lbs. / 27,216 kg
•Dimensions: 42" x 62" x 31" / 1,067 mm x 1,575 mm x 787 mm
•Standard motor: 5 Hp / 208 - 230 VAC / 60 Hz / 1 pH
•Shipping weight: 1,264 lbs. / 573 kg
•Shipping dimensions: 48" x 70" x 30" / 1,219 mm x 1,778 mm x 762 mm
Hydraulic Pipe BenderY440101 Foldable Engine Crane 1 ton
Page 5
Winntec Y471150 Hydraulic Foot Pump Aluminum
700 bar 10 000 psi air/hydraulic pump
with aluminium tank and internal relief
valve. Effective oil capacity 1600 cc. Air
exhaust muffler for quiet operation. Two
stage release mechanism. Pump, hold or
release load with pedal control. Air inlet
1/4 outlet 3/8.Working pressure 6-10 bar
BQ3 Gearbox / Transmission jacks
Capacity 1.5 Ton
Length: 1110mm
Width: 652mm
Height: 190 – 870mm
Net Weight: 130 kg
Capacity 1 Ton
Height: 1150-1960
Net Weight: 46 kg
Y451000 High Lift Gearbox Jack – 1 ton
A chrome main ram and hold-to-run control safety
system. The wide base provides optimum stability
and the efficient pump system ensures fast and
precise reach of the load.
IM- AA0101G Telescopic Gearbox Jack
Rated loading capacity 1 ton
Minimum Height 830mm
Maximum Height 1760mm
G.W. 89kg
N.W. 79kg
Packing size 550 x 370 x 1000mm
IM- HA8000 Headlight Aimer
Measuring Range:
Central Height of Headlight 50cm – 130cm
Light Intensity of High Beam +/- 100cd
Indication Error: Light Intensity of High Beam +/- 12%
Measure distance: 30 – 50cm
Power consumption <0.5W
Dimensions 590mm x 1810 mm x 590mm
Nett Weight 30kg
Environmental Temperature 5 – 40 degrees C
Relative humidity: Less than 95%
Atmosphere Pressure: 70 – 106 Kpa
Power Supply: 9v DC
(If AC power is used an inverter should be used)
Winntec Y450101 Engine Stand
Model Capacity Height Width Length N.W
Y450101 400KG 825 175 275 23
Capacity 400kg
Height 825mm
Width 175mm
N.W. 23kg
Scoda TT - Turn Tables, Mechanical
This portable tyre changer is equipped with professional
accessories, can be operated easily without power and
pneumatic supplies. It can work for different kinds of vehicle
tyres, such as MXT, ATV, scooter, and electro mobiles. It is
perfect for family garage, racing team, long driving journey,
emergencies, and different kinds of automobile garages.
Specifications – SA40
Lifting Capacity 4000 kg
Locking release Manual
Min Height 100 mm
Lifting Height 1900mm
Power of motor 2.2 kw
Oil Pressure 18 MPa
Power Supply 220v
Lifting time 50 s
Lowering Time 40 s
SA40 Two Post Lift with base plate – 4 ton capacity (Manual Release)
Floor plate design, more suitable for
low ceiling workshops. Single side
Manual lock release. Dual cylinders
located in Master and slave column.
Dynamic test 115% of the rated
capacity. Static test: 150% of the rated
capacity. Dual antic skidding safety
device from column ladder safety to
hydraulic seal protection. Special
hydraulic system designed to avoid
overload running. ABS control box,
24v low voltage control system. High
strength chain drive system. High
quality seals from Italy. Quality power
rack. CE Certified - Red
Specifications – SB40
Lifting Capacity 4000 kg
Lock release Manual
Min Height 110 mm
Lifting Height 1900mm
Column Height 3722mm
Power of motor 2.2 kw
Oil Pressure 18 MPa
Power Supply 220v/380v
Lifting time 50 s
Lowering Time 40 s
Clear floor design makes under-vehicle
service more convenient. Manual lock release
on both sides. Dual cylinders located in
Master and slave column. Dynamic test 115%
of the rated capacity. Static test: 150% of the
rated capacity. Dual anti skidding safety
device from column ladder safety to hydraulic
seal protection. Special hydraulic system
designed to avoid overload running. ABS
control box, 24v low voltage control system.
High strength chain drive system, High quality
seals from Italy. CE Certified - Red
SB40 Two Post Lift , Base free – 4 ton capacity (Manual Release)
Specifications – SAE40
Lifting Capacity 4000 kg
Locking release Electrical
Min Height 100 mm
Lifting Height 1900mm
Power of motor 2.2 kw
Oil Pressure 18 MPa
Power Supply 220v
Lifting time 50 s
Lowering Time 40 s
Reinforcement base plate for uneven floor
Floor plate design, more suitable for
low ceiling workshops. Single side
electrical lock release. Dual cylinders
located in Master and slave column.
Dynamic test 115% of the rated
capacity. Static test: 150% of the rated
capacity. Dual antic skidding safety
device from column ladder safety to
hydraulic seal protection. Special
hydraulic system designed to avoid
overload running. ABS control box,
24v low voltage control system. High
strength chain drive system. High
quality seals from Italy. Quality power
rack. CE Certified - Red
Page 6
SAE40 Two Post Lift with base plate – 4 ton capacity (Electric Release)
Reinforcement base plate for uneven floor
SBE40 Two Post Lift , Base free – 4 ton capacity (Electric Release)
Specifications – SBE40
Lifting Capacity 4000 kg
Lock release Electric
Min Height 110 mm
Lifting Height 1900mm
Column Height 3600mm
Power of motor 2.2 kw
Oil Pressure 18 MPa
Power Supply 220v / 380v
Lifting time 50 s
Lowering Time 40 s
Clear floor design makes under vehicle
service more convenient. Single side
electrical lock release. Dual cylinders
located in Master and slave column.
Dynamic test 115% of the rated capacity.
Static test: 150% of the rated capacity .Dual
antic skidding safety device from column
ladder safety to hydraulic seal protection
Special hydraulic system designed to avoid
overload running. ABS control box, 24v low
voltage control system. High quality seals
from Italy. High strength chain drive system
Quality power rack - Red
Specifications – SBE40H
Lifting Capacity 4000 kg
Lock release Electric
Min Height 110 mm
Lifting Height 1900mm
Column Height 3900mm
Power of motor 2.2 kw
Oil Pressure 18 MPa
Power Supply 220v / 380v
Lifting time 50 s
Lowering Time 40 s
Clear floor design makes under vehicle service
more convenient. Single side electrical lock
release. Dual cylinders located in Master and
slave column. Dynamic test 115% of the rated
capacity. Static test: 150% of the rated capacity
.Dual antic skidding safety device from column
ladder safety to hydraulic seal protection Special
hydraulic system designed to avoid overload
running. ABS control box, 24v low voltage
control system. High quality seals from Italy.
High strength chain drive system, Quality power
rack - Red
SBE40H Two Post Lift , Base free – 4 ton capacity - Extended Height (Electric Release)
Specifications – SA4T30
Lifting Capacity 3600 kg
Lifting Height 1800 mm
Power of motor 2.2 kw
Oil Pressure 18 MPa
Power Supply 220v
Lifting time 50 s
Lowering Time 40 s
SA3TP Four Post Exhaust Lift – 3.6 ton capacity
Hydraulic driven, cable lifting system. Single
side manual lock release. Four point
automatic safety locks. Width between
runways non adjustable. Integrated hydraulic
drive system. Conforms with CE requirements
Red
Page 7
IM - LR30 Low Level Lift
Specifications
Supply voltage : 220V
Power : 750W
Max. lifting weight 2.5T
Max. Lifting height 580mm
Lowered height 80mm
Total weight 375KG
Specifications
Supply voltage : 220V
Power : 1.5kW
Max. lifting weight 2.2T
Max. Lifting height 1000mm
Lowered height 130mm
Total weight 300KG
Lifting capacity: 2800kg
Max. lifting height: 400mm
Min. height: 120mm
Platform length: 1350mm
Platform width: 650mm
Approx. Weight: 550 kg
Air Operated
Double Air Bellow
IM – LR45 Heavy Duty Low Level Lift 4.5 ton
Lifting capacity: 4500KG
Max. lifting height: 580 mm
Min. height: 80 mm
Platform length: 1400 mm
Platform width: 580 mm
Product Length: 2100 mm
Product Width: 1900 mm
Scoda SCK-B30 Mid Rise Level Lift
IM– ABL2 Air Bellow Low Level Lift
Page 8
Lifting capacity: 3000KG
Max. lifting height: 1000 mm
Min. height: 110 mm
Platform length: 1400 mm
Platform width: 490 mm
Product Length: 1900 mm
Product Width: 1780 mm
IM – MRL27 Mid Rise Lift
IM- M03804 Air hydraulic Motorcycle (ATV) Lift
Capacity:1000lbs
Min.ht:200mm
Max.ht:850mm
Platform size:2225×605mm
Ramp size:605×550mm
N.W.:165kgs
G.W.:207kgs
Package size:229×67×29.5cm
IM-SD1010ND Air Motorcycle Lift with side ext.
IM-SLA Wheel Alignment Scissors lift
* Robust construction and super-balanced lifts for wheel alignment. * Flush mounted or
surface mounted if access ramps equipped * Electro-hydraulic jack * Leveling controlled
hydraulically * Mechanical safety lock with air operated engagement and release * Manual
emergency lowering * Adjustable position of turntable and longer sliding plate * Adjustable
jack frame * Limit switch for maximum lifting height * High quality hydraulic, pneumatic and
electric components
Specifications – SDW50
Lifting Capacity 5000 kg
Lifting Height 1850 mm
Secondary lifting Height 450 mm
Secondary Lifting weight 3000 kg
Power of motor 3.0 kw
Oil Pressure 18 MPa
Power Supply 220v
Lifting time 50 s
Lowering Time 40 s
Supplied with built in slip plates, recessed for turn tables and auxiliary jacking support
Cylinder located inside of the runway, perfectly protected. Electrical protection devices in
four columns ensure synchronization of runways. Adjustable runways to accommodates
different size vehicles . ABS control box, 24v low voltage control system. Hydraulic hose
and cable protection system . Single side manual lock release. Heavy duty cables, Top
limit switch. Aluminum motor with cooling fan. CE certified
SDW50 Four Post Wheel Alignment Lift – 5 ton capacity
Specifications – SLA
Lifting Capacity 4000 kg
Max raised height 2160 mm
Min lowered height 290 mm
Jack raised height 450mm
Runway length 4800mm
Lenth of jack frame
extended
1600-
1800mm
Overall length 5000mm
Overall width 2050mm
Raised time 60 s
Page 9
Lifting Capacity 360kg
Minimum Height 180mm
Max Height 680mm
NW 107kg
GW 129kg
Packing size 1980 x 580 x 260mm
Platform size 1900 x 530 mm
Air Hydraulic pump. Front wheel clamp for securing motorcycle
Safety bar prevents accidental falling, Adjustable foot for
stability, Removable rear loading ramp.
Equipped with preset and manual inflation * Two outlets for
nitrogen, this product can inflate two tyres at the same time. *
It is also equipped with an air outlet to fill air. * Equipped with
four foot casters * Generates * Nitrogen from your compressed
air *2 Pre-Filters / LED display * 55L internal Nitrogen Storage
Tank. * Remains at last setting * Audible and visual end of the
cycle signal indicators * Automatic vacuum supply and
nitrogen-fill. Power Requirement 100-240Vac 50/60Hz *
Operating Temperature -20º to 70ºC * Compressed Air Input
Range 6-8.5bar * Nitrogen Purity >97% * Nitrogen Output
70L/min @ 9bar/900kPa * Maximum Nitrogen Pressure in
Tank 800kPa/8bar * Accuracy +/-1 psi, 7 kPa, 0.07 bar * Units
of Measurement psi, kPa, bar * Suitable for cars and light
trucks, Green
PN-8890 Nitrogen Generator Cars & Heavy
Trucks
Product Features:
Auto-start inflation * Automatic zero drift adjustment * Remains
at last setting * Audible and visual end of cycle signal indicators
* LCD display * 4 x 8m standard hoses * 4 Nitrogen outlets to fill
Nitrogen * Equipped with four foot casters * Generates Nitrogen
from your compressed air * External 120 liter nitrogen storage
tank * Power Requirement 110/240Vac / 50-60HZ * Power
Consumption 30W * Operating Temperature Range -20 C to
70C * Compressed Air Input Range 6-8.5bar / 600-850kPa *
Nitrogen Purity > 97% * Nitrogen Output 167L/min @ 9bar /
900kPa * Maximum Nitrogen Pressure 8bar / 800kPa * Nitrogen
storage Tank * External 120 liters Suitable for Cars, Light
Trucks – Colour - Green
PN-8850 Nitrogen Generator Cars & Light Trucks
Page 10
Auto-start inflation * Automatic zero drift adjustment *
Remains at last setting* Audible and visual end of the cycle
signal indicators * LCD display * 2 x 8m/26ft standard
hoses * 4 air outlets allow simultaneous inflation of up to 4
tires* Automatic Nitrogen Purge and Fill * 55L internal *
Nitrogen Storage Tank. cycle(N2P) * Power Requirement
100-240Vac 50/60Hz * Operating Temperature -20º to 70ºC
* Compressed Air Input Range 6-8.5bar * Nitrogen Purity
95-99.99% * Nitrogen Output 70L/min (2.5cfm) @
9bar/900kPa * Maximum Nitrogen Pressure in Tank
800kPa/8bar * Accuracy +/-1 psi, 7 kPa, 0.07 bar
Units of Measurement psi, kPa, bar – Green colour
PN-8830 Nitrogen Generator
NPA - Nitrogen Purity
Analyser
Product Features:
It is equipped with an air outlet to fill air. It is equipped
with a Nitrogen outlet to fill Nitrogen * Equipped with
four foot casters * Generates Nitrogen from your
compressed air * 2 Pre-Filters * External 120 liter
nitrogen storage tank * 10m standard hose supplied *
Power Requirement 110/240Vac / 50-60HZ * Power
Consumption 25W * Operating Temperature Range -
20℃C to 70℃C * Compressed Air Input Range * 6-8.5bar
/ 600-850kPa * Nitrogen Purity > 97% * Nitrogen Output
236L/min @ 9bar/900kPa * Maximum Nitrogen Pressure
10bar / 1000kPa * Nitrogen storage Tank External 120
liters * Suitable for Cars, Light Trucks, Heavy Trucks,
Colour Green
PN-8820 Nitrogen Generator
Y444100 / SD0201 Porta Power 10 ton Capacity
Extension tubes snap together in seconds and fit
perfectly without any tolerance. Chrome main
rams guarantee optimum lifetime. Includes
popular hydraulic ram spreader. Repairs dents
and creases in tight places. Attachments push,
pull and lift.
IM- SD0204 Porta Power 20 ton
Capacity: 20 Ton
Min. HT: 282mm
Stroke: 128mm
N.W.(1#): 31.0kgs
G.W.(1#): 32.0kgs
Packing Size: 81x30x20.5cm
N.W.(2#):36.0kg
G.W.(2#):37.0kg
Packing size:81.5x40x11cm
Capacity: 10T
Min. HT: 322mm
Stroke: 130mm
N.W.: 31.5kgs
G.W.: 32.0kgs
Packing Size: 71.5x31x16cm
Winntec Y461501 – Press, Hydraulic
15 ton Capacity
WY461501 -15 ton capacity. This press comes
standard with a two speed pump, arbor and
pressure gauge. Welded ready to use model.
Nine different height positions for securing the
table. Chrome main ram and pump pistons.
Frame height 1730mm, Frame width 740mm,
Hydraulic Stroke 195mm. Weight 131kg
Ram stroke 200mm
Side Stroke 245mm
Working Range 69-1048mm
Bed Width 730mm
Air Pressure 7-8 bar
Air inlet ¼” NTP
N W 303kg
GW 345kg
Package size 98cm x 32cm x 211cm
SD0811CE-Z – Press, Pneumatic
50 ton Capacity
SD0881 – Press Electro Hydraulic
50 ton Capacity
Capacity 50 ton
Output 1.5kW
Voltage 380v
Working Range 210 - 1050mm
Bed Width 730mm
Ram stroke 200mm
N W 287 kg
NW 85kg
GW 329kg
GW 85kg
Package size 99cm x 32cm x 211cm
34cm x 51cm x 74cm
IM-100TP – Press Electro Hydraulic
100 ton Capacity
Capacity 100 ton
Output kW 1.5kW
Voltage 380v
Working Range 177- 1017mm
Bed Width 787mm
Ram stroke 300mm
N W 680 kg
NW 75kg
GW 735kg
GW 88kg
Package size 114cm x 40cm x 211cm
37cm x 53cm x 79cm
Page 11
Junior Rim Straightening Machine
The Atek Junior Rim repair machine is designed to
repair all rims between 10” and 24” with the aid of a
hydraulic piston. The unit is supplied with various
spacers, nuts and bolts to enable the user to mount
the wheel for repairs. A pointer is supplied to aid the
user in identifying dents and other imperfections on
the rims.
Rim diameter 10” – 24”
Working Pressure : 140 bar
• Net weight : 178 kg
• Hydraulic Motor : 0,55 kW / 0,75 hp
The Konig 5700 Rim repair machine is designed to repair all
rims between 10” and 24” with the aid of a hydraulic piston
and a cleaning lathe. Rims can be returned to their original
condition in minutes.
The Konig 5700 is accompanied by various spacers, nuts and
bolts to enable the user to mount any wheel for repairs. An
electro magnetic pointer is supplied to aid the user in
identifying dents and other imperfections on the rims.
Rim diameter 10” – 24”
Working Pressure : 140 bar
• Net weight : 362 kg
• Hydraulic Motor : 0,55 kW / 0,75 hp
• Working Motor : 0,75kW / 1,00 hp
• Rotating Speed 250 RPM
Konig 5700 Rim Straightner with Lathe
Polish - Cln Rim Polisher
Standard Accessories: 5 Piece polishing and
cleaning brushes
Technical Specifications:
Rim Diameter 12” - 28”
Polishing brush size Min 100 x 50 / Max 400 x 50
Rotating Speed 1400rpm
Air working Pressure 8 -10 bar
Polishing working motor 1,5 kW / 1400rpm
Rim rotating motor 0.55kW / 1400rpm
Nett Weight 115 kg
3 phase electric Motor
Pressing positions
Standard accessories
RP2012 - Rim Polisher
Optional Polisher for Atek 5700 Rim Repair Machine
IM-RPK Rim Polish Kit
Page 12
Safety lock system prevents the drawers from opening accidentally, Lateral plates with peg panel design for hanging tools and
various items, Replaceable name tag, heavy duty caster with two-way brake.
Tool Trolley / Cabinets
IM-903B180kg Overall Loading Capacity
IM-907E650kg Overall Loading Capacity,
Dimensions 1226mm x 570mm x 940mm
Weight 125kg
IM-907 600kg Overall Loading Capacity
Dimensions 875mm x 570mm x 1000mm
Weight 87kg
IM-803A 450kg Overall Loading Capacity
Dimensions 575mm x 570mm x 1000mm
Weight 60kg
Page 13
IM-807450kg Overall Loading Capacity
Dimensions 865mm x 570mm x 1000mm
Weight 70kg
Ratchet Type Jack Stands
Model Capacity Min Height Max Height Length Width G.W N.W
Y450301 3 Ton 268 425 190 170 7.5 7
Y451600 6 Ton 394 597 270 240 15.2 13.8
Y451200 12 Ton 440 710 310 260 27.1 26
All stands have a heavy duty robot welded frame, and a multi-position ductile ratchet bar. The quick adjustment mechanism
securely locks into the right location. Includes counter-weighted pawl for safe securing.
Pin Type Type Jack Stands
Model Capacity Min Height Max Height N.W
Y452300 3 Ton 322 465 5.2
Y452600 6 Ton 404 604 11
Pin type support axle stands adjust to multiple height positions. Large support saddle with oil resistant rubber adaptor
for optimal stability and damage free contact; Designed with wide feet for high standard of safety
3 ton capacity. This jack is equipped
with the TURBO LIFTER system,
rubber saddle and handle bumper. The
professional universal joint release
valve makes it possible to lower the
jack with load very precisely and free
from any risks The pump pistons
(protected with jacket to prevent from
intrusion of dirt) are placed at a 45
degree angle so a complete pumping
stroke will always be utilized. The jack
has a chrome main ram.
Y420303 Trolley Jack, Turbo Lifter
3 ton Capacity
Model Capacity Min
Height
Max
Height
Length Width N.W
Y411350 1.35 Ton 80 380 500 240 10
Y420303 3 Ton 130 490 720 360 41
Y420200 2 Ton 140 800 1250 470 58
Y420301 3 Ton 130 600 1305 320 66
Y420500 5 Ton 150 685 1420 355 95
Y421000 10 Ton 160 685 1700 510 145
CIZ-TJ20 20 Ton 180 600 1910 340 165
Y432001 20 Ton 185 373 580 320 47
Y432030 30/15 Ton 150 300 600 305 45
Y432001 - 20 ton capacity.
This heavy duty model is
designed for servicing jobs in
the truck industry. This jack
has an extra extension screw
in addition to 3 saddles that
can be placed on top of each
other for added height.
Chrome main ram and
aluminum air motor guarantee
optimum lifetime. Air filter,
connected to hose included.
All models are equipped with
a foot pedal and
ergonomically designed
handle. These jacks have a
chrome main ram and
professional universal joint
release valve that makes it
possible to lower loads very
precisely and free of any
risks.
Long chassis Trolley Jack
Winntec Y432001 Air service Jack
Winntec Y432030 Telescopic Air Service Jaack
The perfect All-Rounder. This 30/15T jack takes
Winntec air-hydraulic technology to its very
extreme. Its first stage lifts 30T and reaches
220mm. The second stage, with 15T capacity,
reaches another 80mm resulting in a 300mm
maximum height without extensions. With a150mm
low profile this jack is ideal for modern low ground-
clearance vehicles. The jack comes with 3
extensions (10-70-120mm) and has a manual valve
that can close the oil channel (during transport).
Y411350 Trolley Jack, Aluminum
1.35 ton Capacity
1350 kg. This ultra light jack is
equipped with rubber saddle and
nylon wheels. The professional
universal joint makes it possible to
lower the jack with load very
precisely and free of any risk. The
pump piston is placed at a 45˚
angle so a complete pumping
stroke will always be utilized
Page 14
Set consists of:
1 x Demounting Tool, 1 x Mounting Tool, 1 x Bead Keeper
Mount and de-mount all tubeless tires 17.5'' to 24.5''.
Demount tyre in 8 seconds, Re-mount in 20 seconds
without strain - Two simple tools do it all. Works on all
standard tubeless and super single duplex tyres. The
Changing Tools do not damage beads. Mounts and
demount tyres without the need to lift the tyre. The bead
keeper prevent the bead from skipping when mounting
the top bead. Metal construction coated with PVC will not
scratch aluminium wheels
IM- Tubeless Tyre Changing Tool Set
Demounting Tool
Mounting ToolBead Keeper
Technical Data
Motorcycle tire size 5”‐22”
Car tire size 9”‐20”
Weight 34.5KG
SD18 Tyre Changer - Manual
Max Wheel Diameter 960mm
Rim Width 3” – 10”
Outside Clamping 6” – 24”
Rotation Speed 7 rpm
Power 0.75 -1.1kw
Machine weight 175 kg
Specially designed tyre changer for two and four wheel
motorcycle tyres. Special Tool head designed specifically
for easy mounting & dismounting of motorcycle tyres of all
sizes. The shape of the bead breaker blade will easily
break the bead of small , narrow and standard motorcycle
tyres. The sliding clamping jaws have three positions that
will cover from 6” to 24” rims.
M806 Motorcycle Tyre Changer
Max Wheel Diameter 1000mm
Rim Width 4” - 12”
Inside Clamping 12” - 24”
Outside Clamping 10” - 20”
Power 0.75 -1.1kw
Rotation Speed 7 rpm
Machine weight 175 kg
Semi automatic tyre changer with swing arm.
High quality mount/demount foot . Mag protectors
for foot and claws. Water trap & oiler. Stainless
steal bead breaking cylinder.
Optional Motor cycle / ATV adaptor available.
LC810G Semi Automatic Tyre Changer
Page 15
LC885A Automatic Tyre Changer
Max Wheel Diameter 1040mm
Rim Width 3” - 12”
Power 0.75 -1.1kw
Speed 7 rpm
Inside Clamping 12” -24”
Outside Clamping 10” - 20”
Machine weight 240 kg
AL320B Help Arm
Automatic tyre changer with rear tilting arm.
Pneumatic column lock. Mag protectors for foot
and claws. Water trap and oiler. Stainless steal
bead breaking cylinder. Turn tables equipped with
a protective cover.
Optional: Help arm for low profile tyres
887 Automatic Tyre Changer
Max Wheel Diameter 1030mm
Rim Width 3” - 15”
Inside Clamping 13” -26”
Outside Clamping 10” - 24”
Power 0.75-1.1kw
Machine weight 260 kg
Speed Rotation 7 rpm
Automatic tyre changer with rear tilting arm. Pneumatic
column lock. Mag protectors for foot and claws. Water trap
and oiler. Stainless steal bead breaking cylinder. Turn tables
equipped with a protective cover. 80MM Turn tables cylinder
increases clamp force. The design of the bead breaking blade
rotates enabling best bead breaking force.
Optional: Help arm for low profile tyres
AL320B Help Arm
Bright 890PSemi Auto Tyre Changer with Help Arm
Max Wheel Diameter 1250mm – 49”
Max Wheel Width 400mm – 16”
Outside Rim Dia 10-20”
Inside Rim Dia 12-23”
Machine Height (excluding arm) 2040mm
Machine length 1135mm (excluding arm) 1135mm
Machine width (excluding arm) 870mm
Nett Weight (excluding arm) 233kg
Operating Pressure 8-10bar
Motor 1.1kw / 0.75kw
Power 220v / 380v
Turn Table Speed 6rpm
Noise < 70dB
LC887ITS Automatic Lever-less Tyre Changer
Technical parameter:Max. wheel diameter :1040mm
Tire width :3”-15”
Rim diameter :10”-24”/13”-26”
Work air pressure : 8-10bar
Turntable speed : 7-14rpm
Voltage :110V-220V-380V
Power :0.75/1.1Kw
22 inch arc turntable adjustable can
handle tire with the rim diameter of 10-
26inch.
Standard accessories:1-turntable protect plate:protect rim to
avoid the rim being scratched by the
turntable. There is scale on the guard
plate for the convenience to fix the tire;2-Clamping jaw protect cover:Inward
clamping protect the Alu alloy rim to
prevent the rim damageLC588 Truck Tyre Changer
LC590 Truck and OTR Tyre Changer
Max Wheel Diameter 2200mm
Wheel Width 1100mm
Internal Clamping 14” -56”
Working Pressure 150 bar
Machine weight 987 kg
Max Wheel Diameter 1500mm
Wheel Width 1000mm
Power Requirements 1.8kw
Internal Clamping 14” -26”
Working Pressure 150 bar
Machine weight 561 kg
Page 16
IM-QD52 Pneumatic
Tyre Spreader IM- SD-2 Manual Tyre Spreader
Pneumatic upright tyre spreader for cars, light trucks
and minibuses tyres. It is designed for locking and
subsequent spreading of tyres. The machine allows
performing such functions as inspection, sanding,
polishing, dust extraction and patching. The machine
is operated by way of two rubber coated foot
pedals.(Air required). Tyre width: 100-375mm
DB-88 Overturn Vulcanizing Machine
IM- AAT400 Tyre Caddy
Stack Height 1500mm
Weight 17kg
Packing size 850 x 600 x 1530mm
Due to its jaws and easy manoeuvrability,
it allows a pile of tyres to be loaded without
having to touch them by hand
IM-PW150 High Pressure Cleaner
The pressure washer is supplied with five spray nozzles.
Each nozzle is colour coded and delivers a specific
spray pattern. The 0o, 15
o, 25
oand 40
o nozzles are high
pressure nozzles and the chemical nozzle is a low
pressure nozzle.
Power 3Kw
Voltage 380v
R.P.M. 1450 r/min
Flow rate: 9.2 L/min
Max Pressure: 150bar
Suction Lift : 3m
Spray Range:10m
Weight: 45kg
Packing Dimensions: 690 x
400 x 500mm
IM-FY200 (FYMIG5320) Multi
function Mig /Mag Welder
DB-88 Features
It can vulcanize any part of model 750-16 to
model 1000-20 tires in single surface or double
surfaces. It can maintain constant temperature
automatically to ensure the temperature
required during tire vulcanization. It can raise,
lower or overturn the operating bracket to
vulcanize according to the repair position of the
tires of different models. It is equipped with five
moulds in different angle and a purpose made
heat conduct sand bag, which can ensure the
repaired tire more conforms to the normal
condition
Features
The hook can be adjusted according to the
tyre width for medium-sized and small
tyres.
The operating platform can be turned to
any place with ideal light during tyre
repairing.
Page 17
Input voltage: 380v or 220v. Rated input power: 11kva, input
current 17 A (35a/15.7v – 320A/33v, Duty Cycle: 250A/100% -
320A/65%) Frequency 60-1200kHz, Steel wire diameter 0.6-
1.2mm, Alu alloy wire diameter 0.8-1.2mm, Copper alloy wire
diameter, 0.6-1.6mm, Wire feeder, Two way dual drive
IM-XTB1200 HAND SPIN TRUCK WHEEL BALANCER
Mobile – move balancer to the wheel
Adjust height by
rotating the large
wheel
Low revolution
calculation by rotating
the wheel manually
Standard Accessories
IM-XTB820 HAND SPIN CAR WHEEL BALANCER
Hand Brake
Standard Accessories
SD-12B Static Wheel Balancer
CB6 Smart Robot Series Wheel Balancer
Easy operation, wide balancing range. Intelligent and environment protection
Specifications:Max Wheel Diameter: 1118mm
Wheel Width: 1.5--20”
Internal Clamp: 8---28”
Rotation Speed: 140rpm
Working Pressure:100---230V 1ph
Power: 90w
Duration of balancing: 7s
Accuracy: 1g
Load Capacity: 75KG
CB66 base model CB67 semi smart CB68 full smart
Page 18
Max Wheel Diameter 1000mm
Wheel Width 20”
Max Wheel Weight 65kg
Accuracy 1g
Rotation Speed 200rpm
Motor 0.25kW
Power Requirements 220v/1ph
Machine weight 110 kg
Manual data input
CB958B Wheel Balancer
3D Automatic measurement * Multi-
balancing modes * Automatic Wheel
Brake * Up to 4 user modes * Alu Split
weight program * Foldable Display Unit
* Statistical Analysis * Facility to attach
a mini printer
Optional: Wheel Lift
Max Wheel Diameter 1200mm
Wheel Width 20”
Max Wheel Weight 75kg
Accuracy 1g
Rotation Speed 200rpm
Power Requirements 0.25kw
Machine weight 143 kg
CB956B Wheel Balancer
Max Wheel Diameter 1200mm
Wheel Width 20”
Max Wheel Weight 75kg
Accuracy 1g
Rotation Speed 200rpm
Power Requirements 0.25kw
Machine weight 137 kg
2D Automatic measurement * Multi-balancing modes
* Wheel Brake * Up to 4 user modes * Alu Split weight
program * Foldable Display Unit
CB968B Wheel Balancer
Max Wheel Diameter 1200mm
Wheel Width 20”
Max Wheel Weight 75kg
Accuracy 1g
Rotation Speed 200rpm
Power 0.25kw
Machine weight 164 kg
3D Automatic measurement * Multi-balancing
modes * Foot Brake Brake * Up to 4 user
modes * Alu Split weight program * LCD
Display * Statistical Analysis * Lazer Scale
CB460B Truck / Car Wheel Balancer
Max Wheel Diameter 1200mm
Wheel Width 20”
Max Wheel Weight 200kg
Accuracy 1g
Rotation Speed 100/200rpm
Power 0.55kw
Machine weight 269 kg
Equipped with a Wheel Lift
CB910GB Wheel Balancer
Page 19
The tester mainly test low-frequency mechanical
vibration, which make use of ultrasonic telemeter
principle to detect the movement through a
calculated analysis to make the wave re-appear and
evaluate its relevant performance. Test Cycle 3
seconds per wheel. Oscillation displayed as a wave.
Detect distance 0.25m – 1.5 meter. Measurement
distinguishing rate 0.3mm . Results printed on
Thermal printer. Charger: 12v/1A +/-10% output.
Charging time: 5-6 hours
Main Unit dimensions: 161 x 88 x 48.5 mm
Weight: 340g
Power Supply: 8.4 V Battery
Power Consumption: 35mA
(without printing)
Hours of operation: 48 hours
(without printing)
Page 20
Lawrence 3D wheel alignment machine
• 3D max dynamic display system
• No electronic components
• Four – point wheel clamps
• High- speed 3D animation techniques
• Reminding window
• Pre-tightening rotatable jaw
• Pushing the vehicle once
• 3D Animated adjustment guidance
• Animated operation reminding
• Original standard database
• Camera showing vehicle on platform
• Intelligent voice reminding
• Camera and kingpin inclination measurement
•Vehicle body dimension measurement
•Toe out on turn measurement
•Maximum steering measurement
•Tyre diameter measurement
i5
Exquisite movable small cabinet, Height adjustable ruggedized pole, Height Performance computer, 22” LCD monitor, Special
target disk, Deluxe clamping wheel clamps, High definition camera, Steering wheel lock, Brake lock, Wedge shaped pads, turn
tables, Filler plates for turn tables, Printer and Speaker
Priman Preset Tyre Inflators
Power Consumption 20W,
Operating Temperature, Range: -20º
C to 70º C, Max Inlet Air/Nitrogen
Supply : 15bar/1500kPa, Operating
Range : 0.3-12bar/35-1200kPa,
Accuracy : ± 0.07bar/7kPa,
Resolution: 0.1bar/5kPa, Units of
Measurement , PSI/bar/kPa
Dimensions(L*W*H) 360 x 360
x1260mm, Packing Size(L*W*H)
1290 x 200mm, Net Weight 17.5kg
Gross Weight 21kg.
Power Requirement 110/240Vac / 50-60Hz,
Power Consumption 10VA, Operating
Temperature Range -20º to 70º C, Max
Inlet Air Supply 116PSI/8bar/800kPa
Operating Range 5-102PSI/0.3-7bar/35-
700kPa, Over Pressure Setting Range 0-
2bar/0-200kPa, Accuracy ± 0.07bar/7kPa,
Resolution 1PSI/0.1bar/5kPa, Units of
Measurement PSI/bar/kPa, Dimensions (L
*W*H) 230 x 120 x 290mm , Packing
Size(L*W* H) 500 x 290 x 170mm , Net
Weight 4kg, Gross Weight 6.5kg
Feature:
Adjustable Over Pressure Setting (OPS),
Auto-start inflation, Automatic zero drift
adjustment., Remain at last setting,
Comprehensive diagnostics and error
reporting, Audible and visual end of the
cycle signal indicators. Large backlight
LCD display 1 x 10m/32.8ft standard
hose with single clip-on open type chuck,
PA105PA101
BRIGHT SAT – Shock Absorber Tester
PA105 Feature:
Auto-start inflation, Automatic zero
drift adjustment. Remain at last
setting, Comprehensive
diagnostics and error reporting,
Audible and visual end of the cycle
signal indicators. Large backlight
LCD display, 1 x10m/32.8ft
standard hose with single clip-on open type chuck
Same as PA101 but can inflate 4 tyres at a time
PA108
IM- One side lifter
One column electric lift - Screw elevation
system with no fixed position, Mobile -
Easy to use - Under wheel support -
Under car base (sill) with 2 fixing
systems, 220v, Suitable for lifting cars up
to 2500kg, Lifting time for maximum
range: 35 seconds
Maximum height of lifting 1000mm
Wheel dolly – roll, lift, twist, lower. Easy installation and de-installation of truck wheel assemblies.1 man control, Heavy-duty industrial bearings. 3
positions for rollers depending on size of wheel. Great tool for every service truck. Avoid damage to wheel bolts and expensive modern rims. For
all wheels from 6,5 – 22,5
Truck wheel dolly – Heavy Duty
Y-H5201-1 Wheel Dolly Set with storage trolley
4 x Wheel dolly’s with storage trolley
IM-HM5401 Hydraulic Ram Kit
2 Ton Ram
Stroke:76mm
Min. HT:139mm
10 Ton Ram
Stroke:60mm
Min. HT:118mm
10 Ton Ram
Stroke:76mm
Min. HT:139mm
10T (long)
Stroke:150mm
Min.HT:350mm
4T(long)
Stroke:132mm
Min. HT:276mm
2T(pull back ram)
Stroke:128mm
Min.HT:409mm
5T (pull back ram)
Stroke:130mm
Min.HT:483mm
Page 21
Truck wheel dolly - 500kg
AA4C Air Compressors
Page 22
Type: AA-SCP1.1/8
Motor 7.5kW/10HP
Voltage 380v/50Hz/3PH
Capacity(m3/min) 1.1
Working Pressure 8 bar
Weight 240 Kg
Dimensions 890 x 630 x 920mm
Type: AA-10A
Motor 1kW
Voltage 2200v/50Hz/1PH
Capacity(m3/min) 1.5
Working Pressure 8 bar
Weight 40 Kg
Dimensions 700 x 420 x 760mm
Type: 0.6/8
Motor 1kW
Capacity(m3/min) 0.6
Working Pressure 8 bar
Height 1905mm
Type: QPS015 (3 Pcs)
Capacity(m3/min) 1.5
Working Pressure 8 bar
Weight 1.2kg
Height 267.5mm
Screw Compressor
Air Dryer
Tank
Main Filter