cat. n140 iso interface solenoid valve vsr/s 8content2.smcetech.com/pdf/fpt-cpt/vsr-fpt-cpt.pdf ·...
TRANSCRIPT
ISO Interface Solenoid Valve
Size 1, 2 & 3
VSR/S 8
Complies with ISO Standard 5599/2 CSA approved Lateral plug-in type manifold optionLow power Solenoids (1.8W)
CAT. N140
1
ISO 5599/2 Plug-In Product Features ValveISO STANDARD VALVE INTERFACE - SIZES 1, 2 & 3
Higher range of flow rates within each valve size
Choice of seals for maximum flexibility
Available in either high flow rubber seal (model VSR) or matchedground spool and sleeve (model VSS).
Low power consumption: 1.8w DC
Available in 2 or 3 position, single or double solenoid pilot configuration.
Long operating life
• Rubber Seal: 30 million cycles or more• Metal Seal: 50 million cycles or more* Subject to SMC’s own test data using clean and dry air
Meet the following specifications:SAE SPEC: SAE J2051GM SPEC: CC-003
C US
Popular SMC models have been certified by the Canadian Standards Association and bear the CSA trademark. This designation is a registeredmark which signifies that the product has been certified to the applicable CSA and UL standard for use in Canada and the United States. NRTL,i.e. Nationally Recognized Testing Laboratory, is a designation granted by the U.S. Occupational Safety and Health Administration (OSHA) tolaboratories which have been recognized to perform certification to U.S. Standards. Please consult the factory for specific details.
3 0
eziS ledoM laeSevitceffE
mmaera 2
)vC( )1etoN
.cesmemitesnopseR )2etoN
ezistroP ).ni(mmsnoisnemiD )3etoN gthgieW 4etoN
)bl(elgniS elbuoD noitisop31 6-8RSV rebbuR )0.2(63 03 0 5 ₈⁄³⁄41 )4.7x4.4x4.2(5.881x111x26 )12.1(2552 8-8RSV rebbuR )0.4(27 05 05 07 ₂⁄¹
⁄₂¹
⁄₂¹
⁄₂¹
)3.8x9.4x1.3(112x5.521x97 )18.1(4283 01-8RSV rebbuR )4.5(79 08 0 95 5 ₄⁄³
₄⁄³
8⁄³ ₄⁄³
)7.9x4.5x8.3(642x731x69 )12.2(00011 6-8SSV lateM )8.1(23 52 02 54 ⁄₈³ )4.7x4.4x4.2(5.881x111x26 )12.1(2552 8-8SSV lateM )6.3(56 04 0 5 ₂⁄¹ )3.8x9.4x1.3(112x5.521x97 )18.1(4283 01-8SSV lateM )0.5(09 05 5 6 ₄⁄³ )7.9x4.5x8.3(642x731x69 )12.2(0001
₈⁄³
⁄41
2 52 0 ₂⁄¹
1
1
Note 1) Value for valve mounted on an individual subplate. 1⁄2” ports for size 1, 3⁄4” ports for size 2, and 1” ports for size 3.Note 2) At 0.5MPa (71psi).Note 3) Double solenoid type.Note 4) Single solenoid type without base.
Series VS R 8bS
2
roduct Features ValveA variety of manifold & wiring options
• Individual SUP spacer (For size 1 & 2)
• Individual EXH spacer (For size 1 & 2)
• Interface speed controls (For size 1 & 2)
• Interface regulator (For size 1, 2 & 3)
• Terminal box with conduit port
• Serial transmission unit (Device Net)
• Splash proof manifold conforms to IP65 and NEMA4.
CYLINDER WORKING SPEED CHART
ø40 ø50 ø63 ø80 ø100 ø125 ø140 ø160 ø180 ø200
MODEL CV FACTOR CYLINDER SPEED(MM/S)
CYLINDER BORE SIZE (MM)
VSR 8-6(Size 1)
S
VSR 8-8(Size 2)
S
2.0
250
500
750
250
500
750
250
500
750
4.0
5.4VSR 8-10(Size 3)
S
Series VSR8/VSS8
Easily increase or decrease amanifold station without
rewiring the manifold.
Conditions: Pressure :0.5MPa (71psi)Load factor :50%Piping length :5m
• Port Thread CodeNIL Rc (PT)T NPTFF G(PF)
Symbol Port ThreadNIL Rc (PT)F G (PF)N NPTT NPTF
Location of SISU U side manifold block ass’y
• Size of port 1(P), 5(EA), 3(EB)
•
MBS8 080 - SU - 1W
D D sideU U sideB Both side
ISO Size •1 Size 12 Size 23 Size 3
Symbol Size Applicable ISO size02 1/4 Size 103 3/8 Size 1, 204 1/2 Size 1, 206 3/4 Size 2, 310 1 Size 3
Symbol Port location Applicable ISO size02 Side 1/4 Size 103 Side 3/8 Size 1, 204 Side 1/2 Size 1, 2, 306 Side 3/4 Size 2, 310 Side 1 Size 3
02B Bottom and side 1/4 with plug on side Size 103B Bottom and side 3/8 with plug on side Size 1, 204B Bottom and side1/2 with plug on side Size 2, 306B Bottom and side 3/4 with plug on side Size 302S Side and bottom 1/4 with plug on bottom Size 103S Side and bottom 3/8 with plug on bottom Size 1, 204S Side and bottom 1/2 with plug on bottom Size 2, 306S Side and bottom 3/4 with plug on bottom Size 3
Series VS R 8S
3
SU0 No optionSUQW DeviceNet serial interface (Note)TU1 Terminal Box
Note: Please ask available protocol to SMC
HOW TO ORDER ISO5599/2 VALVE MANIFOLD
VV8 2 5 - 03 - TU1 03 D T - W1
• Location of port 1(P), 5(EA), 3(EB)
U side option •
• Locations and sizes of port 4(A), 2(B)
• Conduit Port Thread (for terminal box only)
•ISO Size •
060 Size 1080 Size 2100 Size 3
Number of Stations •2 2 stations
9 9 stations
SERIAL INTERFACE MANIFOLD BLOCK ASS'Y
W1=NEMA 4
Series VS R 8S
4
OPTIONSNILXG ISO 1179-1 THREAD SPEC
•
•1W=NEMA 4
PORT THREADNIL Rc(PT)T NPTFF G(PF)•
•ISO SIZE8060 ISO 18080 ISO 28100 ISO 3
VALVE MANIFOLD BLOCKS
HOW TO ORDER LATERAL PLUG-IN MANIFOLD BLOCKS
CODE A, B, PORT SIZE / LOCATION APPLICABLE ISO SIZE02 1/4" SIDE ONLY 103 3/8" SIDE ONLY 1, 204 1/2" SIDE ONLY 1, 2, 306 3/4" SIDE ONLY 2, 310 1" SIDE 3
02B 1/4" BOTTOM 103B 3/8" BOTTOM 1, 204B 1/2" BOTTOM 2, 306B 3/4" BOTTOM 302S 1/4" SIDE 103S 3/8 SIDE 1, 204S 1/2" SIDE 2, 306S 3/4" SIDE 3
NOTES
NO PORTS ON BOTTOM OF MANIFOLD
SIDE PORTS PLUGGED
BOTTOM PORTS PLUGGED
MANIFOLD ENDD DownstreamU Upstream
HOW TO ORDER LATERAL PLUG-IN MANIFOLD END PLATES
MES 808 D - 04 T - 1W
•
•
•
1W=NEMA 4
PORT THREADNIL Rc(PT)T NPTFF G(PF)
•
•ISO SIZE806 ISO 1808 ISO 2810 ISO 3
Device Net Serial Interface Module Manifold Block
Device Net Serial Interface Module EX230 - SDN1MBS 8080 - SU - 1W NOTE:
NOTE: When ordering parts for assembly. (2) AXT502-34-"*" (use"*" for number of stations) tie rods must be orderedseparately for size 1 only. If only connecting size 1 end plates to manifold. (2) AXT502-4-2 must be ordered separately.
MBS 8080 - 04B T - 1W - XG•
PORT SIZE APPLICABLE ISO SIZE02 1/4 Size 103 3/8 Size 1, 204 1/2 Size 1, 206 3/4 Size 2, 310 1 Size 3
PORT THREADNIL Rc(PT)T NPTFF G(PF)
P, EXH. PORT SIZE APPLICABLE ISO SIZE02 1/4" 103 3/8" 1, 204 1/2" 1, 2, 306 3/4" 2, 310 1" 3
5
SSeries VS R 8 Rubber Seal
CODE A, B, PORT SIZE / LOCATION APPLICABLE ISO SIZE02 1/4" SIDE ONLY 103 3/8" SIDE ONLY 1, 204 1/2" SIDE ONLY 1, 2, 3
02B 1/4" BOTTOM 2, 303B 3/8" BOTTOM 1, 202S 1/4" SIDE 103S 3/8 SIDE 1, 2
PORT THREADNIL Rc(PT)T NPTFF G(PF)
HOW TO ORDER MANIFOLD ASSEMBLIES FOR (4-PIN EURO CONNECTOR) PLUG-IN VALVE BASES
VV8 1 5 - 03S - W 03 D T - X6
•
•
4-PIN EURO CONNECTORX6X13X17X53
* For wiring options, please refer to page 13 for more information.
P, EXH. PORT LOCATIOND DOWN STREAMU UP STREAMB BOTH
NUMBER OF STATIONS2 2 STATIONS: :: :
10 10 STATIONS
ISO SIZE1 ISO 12 ISO 23 ISO 3
•
••
•
•
NOTES
NO PORTS ON BOTTOM OF MANIFOLD
SIDE PORTS PLUGGED
BOTTOM PORTS PLUGGED
HOW TO ORDER LATERAL PLUG-IN MANIFOLD BLOCKS WITH 4-PIN EURO CONNECTOR
MBS 8080 - 04B T -1W - X6
•
•
1W=NEMA 4
•
•ISO SIZE
8060 ISO 18080 ISO 2
CODE A,B, PORT SIZE / LOCATION APPLICABLE ISO SIZE02 1/4" SIDE ONLY 103 3/8" SIDE ONLY 1, 204 1/2" SIDE ONLY 1, 2, 3
02B 1/4" BOTTOM 103B 3/8" BOTTOM 1, 202S 1/4" SIDE 103S 3/8" SIDE 1, 204S 3/4" SIDE 2, 3
NOTESNO PORTS ON BOTTOM OF MANIFOLD
SIDE PORTS PLUGGED
BOTTOM PORTS PLUGGED
VALVE MANIFOLD BLOCKS
•
4-PIN EURO CONNECTORX6X13X17X53
* For wiring options, please refer to page 13 for more information.
Series VS R 8bS
6
(A)(B)
(EA)(P)(EB)
4 2
5 1 3
Single solenoid (FG-S)
(A)(B)4 2
5 1 3(EA)(P)(EB)
Double solenoid (FG-D)(Metal)
(A)(B)4 2
5 1 3(EA)(P)(EB)
(A)(B)
(EA)(P)(EB)
4 2
5 1 3
Double solenoid (FG-D)(Rubber)
Closed center (FHG-D)
(A)(B)
(EA)(P)(EB)
4 2
5 1 3
Exhaust center (FJG-D)
(A)(B)
(EA)(P)(EB)
4 2
5 1 3
Pressure center (FIG-D)
2-position
3-position
RUBBER SEAL/METAL SEAL
SERIES VSR8/VSS8
•Subplate (NPTF)NIL Without Subplate
A02T Side 1/4 For VSR/S8-6A03T Side 3/8 For VSR/S8-6, 8-8A04T Side 1/2 For VSR/S8-6, 8-8, 8-10A06T Side 3/4 For VSR/S8-8, 8-10A10T Side 1 For VSR/S8-10B02T Bottom 1/4For VSR/S8-6B03T Bottom 3/8For VSR/S8-8B04T Bottom 1/2For VSR/S8-10
•Rated voltage3EZ 24VDC4EZ 12VDC
• Special OptionsNIL StandardX1 External Pilot Supply
P, EXH. PORT LOCATIONA02 1/4" SIDEB02 1/4" BOTTOMA03 3/8" SIDEB03 3/8" BOTTOMA04 1/2" SIDEB04 1/2" BOTTOMA06 3/4" SIDEA10 1" SIDE
Series VS R 8 Rubber SealS
7
•
Number of Solenoid•
S SingleD Double
VS R 8 - 6 - FG - S - 3EZ - V1 A03T - X1Type of seal•
R RubberS Metal
Size•6 Size 18 Size 210 Size 3
Configuration•FG 2-positionFHG 3-position, Closed centerFJG 3-position, Exhaust centerFIG 3-position, Pressure center YHZ 3-position, Dual Closed centerYIZ 3-position, Dual Pressure centerYJZ 3-position, Dual Exhaust centerYZ 2-position, Dual Pressure
HOW TO ORDER VALVE
DESCRIPTION PART#VS8-1-A03T with 4 pin micro-connector US15893VS8-2-A04T with 4 pin micro-connector US2249VS8-3-A06T with 4 pin micro-connector US18552
ISO SUB BASES WITH 4-PIN CONNECTORS
PORT THREADNIL RC(PT)T NPTFF G(PF)
HOW TO ORDER ISO SUB-BASES
VS8 - 1 - A03 T - - XG
•
••
ISO SIZE1 ISO 12 ISO 23 ISO 3
•
* Consult an SMC representative for other voltage options.
Note: Blue Colour Coded Coil for 24VDC
**
**
YIZ - 3 Position, Dual Exhaust CenterYJZ- 3 Position, Dual Pressure CenterNote: When used with Dual Sandwitch Regulator
OPTIONSNILXG ISO 1179-1 THREAD SPEC
4-PIN EURO CONNECTORX6X11X53
* For wiring options, please refer to page 13 for more information.
•Pilot Exhaust OptionsNIL Pilot Exh. through footprintV1 External Individual Pilot Exhaust
Series VS R 8bS
8
1. Piston assembly A
2. Piston assembly B
3. Gasket
4. Gasket
5. Return spring A
6. Return spring B
7. Detent assembly
8. Pilot valve assembly
VSS8-6
VS8060-8A-1
–
VS8060-17-1
VS8060-19-1
VFS3000-17-1
–
–
SF4-mF-30
Single solenoid
VSS8-8
VS8080-8A-1
VS8080-8A-4
VS8080-17-1
VS8080-19-1
VF4000-18-1
–
–
SF4-mF-30
VSS8-10
VS8080-8A-1
VS8080-8A-4
VS8080-17-1
VS8100-19-1
VF4000-18-1
–
–
SF4-mF-30
VSS8-6
VS8060-8A-2
VS8060-8A-3
VS8060-17-1
VS8060-19-1
–
–
VFS3000-9A
SF4-mF-30
Double solenoid
VSS8-8
VS8080-8A-1
VS8080-8A-2
VS8080-17-1
VS8100-19-1
–
–
VF4000-12A
SF4-mF-30
VSS8-10
VS8080-8A-1
VS8080-8A-2
VS8080-17-1
VS8060-19-1
–
–
VF4000-12A
SF4-mF-30
VSS8-6
VS8060-8A-4
–
VS8060-17-1
VS8060-19-1
VS8060-17-2
–
–
SF4-mF-30
3-position
VSS8-8
VS8080-8A-3
–
VS8080-17-1
VS8080-19-1
VF4000-18-2-1
VF4000-18-2-2
–
SF4-mF-30
VSS8-10
VS8100-8A-1
–
VS8080-17-1
VS8080-19-1
VF4000-18-2-1
VF4000-18-2-2
–
SF4-mF-30
PART LIST
Description
Series VSS8 (Metal Seal Type)Single Solenoid
Double Solenoid
3-position
VSS8-6
VSS8-6
VSS8-6
CONSTRUCTION
5
VSS8-6
VSS8-6
SERIES VSS (METAL SEAL TYPE)SINGLE SOLENOID
DOUBLE SOLENOID
3-POSITION
VSS8-6
Single solenoid Double solenoid 3 positionVSS8-6 VSS8-8 VSS8-10 VSS8-6 VSS8-8 VSS8-10 VSS8-6 VSS8-8 VSS8-10Description
1. Piston assembly A - - - - - - - - -
2. Piston assembly B - - - - - - - - -
3. Gasket - - - - - - - - -
4. Gasket VS8060-19-1 VS8060-19-1 VS8060-19-1 VS8060-19-1 VS8060-19-1 VS8060-19-1 VS8060-19-1 VS8060-19-1 VS8060-19-1
5. Return spring A - - - - - - - - -6. Return spring B - - - - - - - - -7. Detent assembly - - - - - - - - -8. Pilot valve assembly SF4-w F-30 SF4-w F-30 SF4-w F-30 SF4-w F-30 SF4-w F-30 SF4-w F-30 SF4-w F-30 SF4-w F-30 SF4-w F-30
Series VS R 8 Rubber Seal
9
S
1. Piston assembly A
2. Piston assembly B
3. Gasket
4. Gasket
5. Return spring A
6. Return spring B
7. Detent assembly
8. Pilot valve assembly
VSR8-6
VS8060-8RA-1
–
VS8060-17-1
VS8060-19-1
VFR3000-8-1
–
–
SF4-mF-30
Single solenoid
VSR8-8
–
VS8080-8RA-1
VS8080-17-1
VS8080-19-1
–
–
–
SF4-mF-30
VSR8-10
–
VS8100-8RA-1
VS8080-17-1
VS8080-19-1
VS8100-12R-1
–
–
SF4-mF-30
VSR8-6
VS8060-8RA-1
VS8060-8RA-2
VS8060-17-1
VS8060-19-1
–
–
–
SF4-mF-30
Double solenoid
VSR8-8
–
–
VS8080-17-1
VS8080-19-1
–
–
–
SF4-mF-30
VSR8-10
–
–
VS8080-17-1
VS8080-19-1
–
–
–
SF4-mF-30
VSR8-6
VS8060-8RA-3
–
VS8060-17-1
VS8060-19-1
VFR3000-9-1
–
–
SF4-mF-30
3-position
VSR8-8
VS8080-8RA-1
–
VS8080-17-1
VS8080-19-1
VS8080-12R-2
–
–
SF4-mF-30
VSR8-10
VS8080-8RA-1
–
VS8080-17-1
VS8080-19-1
VS8080-12R-2
–
–
SF4-mF-30
PART LIST
Description
Series VSR8 (Metal Seal Type)Single Solenoid
Double Solenoid
3-position
VSR8-6
VSR8-6
VSR8-6
CONSTRUCTION
6
SERIES VSR (RUBBER SEAL TYPE)SINGLE SOLENOID
DOUBLE SOLENOID
3-POSITION
Single solenoid Double solenoid 3 positionVSS8-6 VSS8-8 VSS8-10 VSS8-6 VSS8-8 VSS8-10 VSS8-6 VSS8-8 VSS8-10Description
1. Piston assembly A - - - - - - - - -
2. Piston assembly B - - - - - - - - -
3. Gasket - - - - - - - - -
4. Gasket VS8060-19-1 VS8060-19-1 VS8060-19-1 VS8060-19-1 VS8060-19-1 VS8060-19-1 VS8060-19-1 VS8060-19-1 VS8060-19-1
5. Return spring A - - - - - - - - -6. Return spring B - - - - - - - - -7. Detent assembly - - - - - - - - -8. Pilot valve assembly SF4-w F-30 SF4-w F-30 SF4-w F-30 SF4-w F-30 SF4-w F-30 SF4-w F-30 SF4-w F-30 SF4-w F-30 SF4-w F-30
Series VS R 8bS
10
VALVES
SMC
14
12 SMC
SMC
SMC
14 14
1212
SIZE 1SIZE 1SIZE 2SIZE 2SIZE 3SIZE 3
205205228228
AA188.5188.5
110.5110.5122122
BB103103
25253232
1919CC
50506464
DD3838
67.567.57171
6565EE
175175198198
150.5150.5FF
AA
BBCC
DD
EE EE
BB
FF
CC
DD
INDICATORINDICATORLIGHTLIGHT
MANUALMANUALOVERRIDEOVERRIDE
MANUALMANUALOVERRIDEOVERRIDE
INDICATORINDICATORLIGHTLIGHT
ALL DIMENSIONS ARE IN MILLIMETERSALL DIMENSIONS ARE IN MILLIMETERS
11
Series VS R 8 Rubber SealS
ISO SIZE 1 SUB-BASE
VS8-1-w 02/03/04w
55 11 33
1414 44 22 1212
P
EA EB
AA BB
2-1/8PILOT EXH PORTS
2-1/4, 3/8, 1/2A, B PORTS
M12 CONNECTOR(OPTIONAL)
2-Ø7MOUNTING HOLES
LL
1533.5
29.529.5
43.5
25
46.5
25
23 23
11.5
17
18
1212
5-1/4 PORTS
49.5
152.5
165.5
15 30.5 45
22.5 22.5
2-3/8EA, EB PORTS
1/4, 3/8, 1/2P PORT
ALL DIMENSIONS ARE IN MILLIMETERS
1/2 - 30.5
3/8 - 27
L = 1/4 - 23.5
Series VS R 8bS
12
ISO SIZE 2-3 SUB-BASE
VS8- w 03/04/06/10w
EA EB
P
15 3
414 2 12
A B
SIZE 2SIZE 3
A B C D E F G H I J
SIZE 3SIZE 2
K L M N O P Q R
* 28 48.5 36 32.5 52 32.5 47.5
19 17.5 15.5 27 187.5 174.5 58 19
22 27 47 45 40 65 40 71
14 26 19 40 234 221 76 27
S4139
29 8.5** 22
T5765
AA
B
C
DD
E
F
G
H
**I37
**I39
J
K
L
MM
N N
QPO
R
S T
2-1/8PILOT EXH PORTS
SIZE 2 - 3/8, 1/2, 3/4SIZE 3 - 1/2, 3/4, 12 PORTS - A,B, PORTS
SIZE 2 - ø7SIZE 3 - ø9
2 MOUNTING HOLES
SIZE 2 - 3/8SIZE 3 - 1/2
5 PORTS
SIZE 2 - 1/2SIZE 3 - 3/4
2 PORTS - EA, EB PORTS
SIZE 2 - 3/8, 1/2, 3/4SIZE 3 - 1/2, 3/4, 1P PORT
M12 CONNECTOR(OPTIONAL)
ALL DIMENSIONS ARE IN MILLIMETERS
* 3/8 - 14.5 1/2 - 16 3/4 - 18.5
Series VS R 8 Rubber SealS
13
TERMINAL STRIP 22 POSITIONTERMINAL STRIP 22 POSITION
TERM P12=OUT 11TERM P12=OUT 11
TERM P11=OUT 10TERM P11=OUT 10
TERM P7=OUT 6TERM P7=OUT 6
TERM P8=OUT 7TERM P8=OUT 7
TERM P9=OUT 8TERM P9=OUT 8
TERM P10=OUT 9TERM P10=OUT 9
TERM P6=OUT 5TERM P6=OUT 5
TERM P5=OUT 4TERM P5=OUT 4
TERM P1=OUT 0TERM P1=OUT 0
TERM P2=OUT 1TERM P2=OUT 1
TERM P3=OUT 2TERM P3=OUT 2
TERM P4=OUT 3TERM P4=OUT 3
TERM P20=ITV +24TERM P20=ITV +24
TERM P21=ITV_IN0TERM P21=ITV_IN0
TERM P22=ITV_IN1TERM P22=ITV_IN1
TERM P19=PETERM P19=PE
TERM P18=OVTERM P18=OV
TERM P16=OUT 15TERM P16=OUT 15
TERM P15=OUT 14TERM P15=OUT 14
TERM P14=OUT 13TERM P14=OUT 13
TERM P13=OUT 12TERM P13=OUT 12
TERM P17=OVTERM P17=OV
1122
33 44
M12 MICRO CONNECTORM12 MICRO CONNECTOR
X11X11 PIN 1PIN 1 NOT USEDNOT USED
OPTIONOPTION
PIN 2PIN 2 12 (B) +12 (B) +
PIN 3PIN 3 COMMONCOMMON
PIN 4PIN 4 14 (A) +14 (A) +
NOT USEDNOT USED
12 (B) +12 (B) +
COMMONCOMMON
PIN 2PIN 2
PIN 4PIN 4
PIN 3PIN 3
14 (A) +14 (A) +PIN 1PIN 1X53X53
OPTIONOPTION
SUB-BASESUB-BASE
14 (A) +14 (A) +
COMMONCOMMON
12 (B) +12 (B) +
NOT USEDNOT USEDPIN 1PIN 1X6X6
PIN 2PIN 2
PIN 3PIN 3
PIN 4PIN 4
PIN 1PIN 1
PIN 4PIN 4
PIN 2PIN 2
PIN 3PIN 3
PIN 4PIN 4
PIN 3PIN 3
PIN 2PIN 2
X13X13 NOT USEDNOT USED
12 (B) +12 (B) +
COMMONCOMMON
14 (A) +14 (A) +
COMMONCOMMON
12 (B) +12 (B) +
NOT USEDNOT USED
OPTIONOPTION
PIN 1PIN 1
MANIFOLD BLOCKMANIFOLD BLOCK
OPTIONOPTION
X53X53 14 (A) +14 (A) +
PIN 3PIN 3 COMMONCOMMON
12 (B) +12 (B) +PIN 4PIN 4
NOT USEDNOT USED
14 (A) +14 (A) +
X6X6
PIN 2PIN 2
PIN 1PIN 1
COMMONCOMMONPIN 3PIN 3
PIN 4PIN 4 14 (A) +14 (A) +
12 (B) +12 (B) +
NOT USEDNOT USEDX17X17
PIN 2PIN 2
PIN 1PIN 1
WIRING INFORMATION
Series VS R 8bS
14
INTERFACE OPTIONS
Applicable solenoid valve VSR/S8-6 VSR/S8-8 VSR/S8-10
Individual SUP Spacer VV81-P-02/03/04w VV82-P-03/04/06w VV83-P-10T-X66US
Individual EXH Spacer VV81-R-02/03/04w VV82-R-03/04/06w
Interface Speed Control VVS8060-22A VVS8080-22AValve Dual Sandwich Regulator W/Gauge VVS8060-ARB-YAB-1 VVS8080-ARB-YAB-1 VVS8100-ARB-YAB-1Valve Single Sandwich Regulator NARB250-NO-w-1 NARB350-NO-w-1 VVS8100-ARB-w-1
ARB250-00-w-1 ARB350-00-w-1Blank Plate, Ass'y VVS8060-11A VVS8080-11A VVS8100-11A
Blocking Disk VVS8060-14A
Blocking Disk [1(P) Port] VVS8080-14A VVS8100-14A
Blocking Disk [3(EB) Port] VVS8080-15A VVS8100-14A
Blocking Disk [5(EA) Port] VVS8080-15A VVS8100-14A
Description ISO Size 1 ISO Size 2 ISO Size 3
STANDARD SPECIFICATIONS
NOTE: For Iinterface speed controllers ISO Size 3 consult SMC Pneumatics.
Series VS R 8 Rubber SealS
15
P(1)
P(1)A(4)
EA(5) A(4)
B(2) EB(3)
B(2) EB(3)
"DUAL" SANDWICH REGULATOR
VALVE MOUNTING SURFACEVALVE MOUNTING SURFACE
-- ++COL K
SSMM
CCSP
ACER
REG
ULA
TOR
SPAC
ER R
EGU
LATO
R
SMC
SIZE 3SIZE 2
A B C D E F G H I JSIZE 1
CB
A
F
G
HI
JE
D
294338
427.5
--
287
141163.2208.5
153174.7
219
10097
100.4
21.327.835.3
42.655.670.6
3535
48.2
59.557.681.2
124.5120133
NOTE:1) FOR APPLICATIONS USING DUAL PRESSURE REGULATORS THE CONFIGURATION OF VALVES TO USE ARE "YZ" STYLE FOR 2 POSITION "YHZ" AND "YJZ" STYLE FOR 3 POSITION.
2) FOR APPLICATIONS USING SIZE 3 "A" AND "B" STYLE REGULATORS THE CONFIGURATION OF VALVES TO USE ARE "YZ" STYLE FOR 2 POSITION "YHZ" AND "YJZ" STYLE FOR 3 POSITION.
3) ALL DIMENSIONS ARE IN MILLIMETERS
REGULATORS
Series VS R 8bS
16
MANIFOLD M12 CONNECTORS
22
44
22
44
22
44
SMCSMC
SMC SMC
1212
1414
SMC SMC
SMCSMC
1414
1212
1414
55SM
CSM
C11
33
1212
SIDE USIDE D n 3 STATION2 1
LENGTH FORMULAL1= 43n + 72L2= 43n + 84
n
L2
L
L1
471
459287
LENGTH DIMENSIONS
299
5432
201
213170
158
256
244
9876
373
385342
330
428
416
10
514
502
L1
L2
B
A
E
D
C
F
G
H
SR
Q
UT
V W
X
Y Z
AA
BB
II
K
J
LM
N
O
P
SIZE 1SIZE 2SIZE 3
L2= 56n + 106
370
386
LENGTH DIMENSIONS
n
L2
L1
L
274218 330
258202
2 3
314
4 5
594
610498442 554
482426
6 7
538
8 9
666
10
650
LENGTH FORMULAL1= 56n + 90
n= NUMBER OF STATIONS (MIN. 2, MAX. 10)
L
303
279
L2
L1
232
208
587
563
445
421
374
350
516
492
729
705
658
634
800
776
L2= 71n + 90L1= 71n + 66LENGTH FORMULA
32n
LENGTH DIMENSIONS
754 6 98 10
MANUALOVERRIDE
INDICATORLIGHT
CC
SIZE 1 SIZE 2 SIZE 3
177.5A
119B
9C
50.5D
48.5E
58.5F
87G
105H
20.5I
26.5J
20.5K
30.5L
58.5M
22N
45.5O
52P
81Q
49R
18S
5.5T
SIZE 1
SIZE 3SIZE 2
57.51.5U V
142543W X
242Y Z
133AA BB
1/8-4 PORTSPILOT PORTS
PITCH
189.5 125 9 52 52.5 64.5 96.5 112
1 73 56 35 53 2 20 150.5
234.5 142.5 13 77.5 79.5 92 108 123.5
4 68.5 71 30 45 2 20 175.5
CC188.5
199244
26 34 26 37 64.5 31.5 58.5 67.5 97.5 58.5 20.5 341 52 41 52 92 36 69 82.5 121 74 28 4
NOTE #1
NOTE #2
NOTES:1) SIZE 1 - 1/4, 3/8, 1/2 SIZE 2 - 3/8, 1/2, 3/4 SIZE 3 - 3/4, 1 6 PORTS, 1, 3, 5 PORTS2) SIZE 1 - 1/4, 3/8, 1/2 SIZE 2 - 3/8, 1/2, 3/4 SIZE 3 - 1/2, 3/4, 1
2 PORTS, 2, 4 PORTS3) ALL DIMENSIONS ARE IN MILLIMETERS
Series VS R 8 Rubber SealS
17
MANIFOLD WITH TERMINAL BOX
44
2222
44
22
44
22
44
SMCSMC
SMC SMC
1212
1414
SMC SMC
SMCSMC
1414
1212
14
5SM
C1
3
12
SIDE USIDE D n 3 STATION2 1
L1
L2
B
A
E
D
C
F
G
H
SR
Q
U T
V W
X
Y Z
AA
BB
I
K
J
LM
N
O
P
MANUALOVERRIDE
INDICATORLIGHT
1/8-4 PORTSPILOT PORTS
PITCH
NOTE #1
NOTE #2
NOTES:1) SIZE 1 - 1/4, 3/8, 1/2 SIZE 2 - 3/8, 1/2, 3/4 SIZE 3 - 3/4, 1 6 PORTS, 1, 3, 5 PORTS2) SIZE 1 - 1/4, 3/8, 1/2 SIZE 2 - 3/8, 1/2, 3/4 SIZE 3 - 1/2, 3/4, 1
2 PORTS, 2, 4 PORTS3) ALL DIMENSIONS ARE IN MILLIMETERS
4
CC
L1= 56n + 90LENGTH FORMULA
LENGTH DIMENSIONS
L2= 56n + 106
n= NUMBER OF STATIONS (MIN. 2, MAX. 10)
299
LENGTH DIMENSIONS
287
170L2 213 256
158
2
LENGTH FORMULAL1= 43n + 72L2= 43n + 84
Ln
L1
3
201
4
244 502
514385342 428 471
373330
65 7
SIZE 1
8
416
9
459
218L2 274 330
2
202
10 n
L1
L
258
3 4
314
LENGTH DIMENSIONS
LENGTH FORMULAL1= 71n + 66L2= 71n + 90
350
374498442386 554 610
7
482426
5
370
6
SIZE 2
8
538
9
594
232666 L2 303
208
10
650
n
L1
L 3
279
2 4
SIZE 3
587445 516 658 729
563
5
421
6
492 634
87 9
705
800
10
776
20.5
SIZE 2SIZE 3
SIZE 1
SIZE 3SIZE 2SIZE 1
14
U1.5
7368.5
V57.5
234.5189.5
A177.5
142.5125
B119
5671
W43
3530
X25
139
C9
77.552
D50.5
5345
Y42
22
2Z
79.552.548.5
E
64.592
58.5F
96.5159
182.52020
AA14 145.5
BB
10896.5
87G
112123.5
105H
110.5133.5
CC
26.52641
20.5I
5234
J
2820.5
1858.545.5
64.558.530.5
4126
K
5237
L
31.592
M
36
N22
12197.567.5
82.569
O P52
7458.5
Q81
R49 5.5
S
43
T
Series VS R 8bS
18
OU
TO
UT
88 00
/NET
/NET
MO
DM
OD
PWR
PWR
FLASHING:SHORTOUTPUT(DIAGNOSESIN0-15)
FLASHING:SHORT OUTPUT(DIAGNOSES IN 0-15)
SERIAL
UN
ITSERIA
L UN
IT
11
EX230-SD
N1
EX230-SD
N1
00
SETTING
SSETTIN
GS
TMTM
IN23
IN23
IN21
IN211414
1515
6677
IN22
IN22
12121313
IN20
IN20
4455
IN19
IN19
IN17
IN17
IN18
IN18
IN16
IN16
EPREPR
VLV
VLV
991010
1111
2233
11
AU
TOA
UTO
RESETRESET
BU
SB
US
ININ
44
22
INPU
TIN
PUT
111.2
4V1.2
4V
5 52 2
4 4
335.
PE5.
PE
4.IN1
84.I
N18
3.0V
3.0V
2.IN1
72.I
N17
5 52 2
4 4
3 311
5.PE
5.PE
4.IN1
94.I
N19
3.0V
3.0V
3.0V
3.0V
2.NC
2.NC
(FEM
ALE)
(FEM
ALE)
5PIN
5PIN
MIC
ROCO
NNEC
TOR
MIC
RO C
ONN
ECTO
R
5 52 2
4 4
3 311
5.PE
5.PE
4.IN2
04.I
N20
3.0V
3.0V
2.IN2
12.I
N21
1.24V
1.24V
2.V
+2.
V+
1.D
RAIN
1.D
RAIN
BUS
INBU
S IN
223 3
44
5PIN(
MALE
)5P
IN(MA
LE)
MINI
CONN
ECTO
RMI
NI CO
NNEC
TOR
5.CA
NL
5.CA
N L
4.CA
NH
4.CA
N H
3.V
-3.
V-
3 31 1VL
VPWR
INVL
V PWR
IN
1155
2.N
C2.
NC
1.24
V1.
24V
4422 4P
IN(MA
LE)
4PIN(
MALE
)MI
NICO
NNEC
TOR
MINI
CONN
ECTO
R
4.0V
4.0V
3.N
C3.
NC
22
44
22
44
22
44
SMCSMC
SMC SMC
1212
1414
SMC SMC
SMCSMC
1414
1212
1414
55SM
CSM
C
SMC
SMC
11
33
1212
SIDE USIDE D nn 33 STATION22 11
LENGTH FORMULAL1= 43n + 72L2= 43n + 84
n
L2
L
L1
471
459287
LENGTH DIMENSIONS
299
5432
201
213170
158
256
244
9876
373
385342
330
428
416
10
514
502
L1L1
L2L2
BB
AA
EE
DD
CC
FF
GG
HH
SSRR
UUTT
VV WW
XX
YY ZZ
AAAA
BBBB
II
KK
JJ
LLMM
NN
OO
PP
L2= 56n + 106
370
386
LENGTH DIMENSIONS
n
L2
L1
L
274218 330
258202
2 3
314
4 5
594
610498442 554
482426
6 7
538
8 9
666
10
650
LENGTH FORMULAL1= 56n + 90
n= NUMBER OF STATIONS (MIN. 2, MAX. 10)
L
303
279
L2
L1
232
208
587
563
445
421
374
350
516
492
729
705
658
634
800
776
L2= 71n + 90L1= 71n + 66LENGTH FORMULA
32n
LENGTH DIMENSIONS
754 6 98 10
MANUALOVERRIDE
INDICATORLIGHT
SIZE 1 SIZE 2 SIZE 3
1/8-4 PORTS1/8-4 PORTSPILOT PORTSPILOT PORTS
PITCH
NOTE #1
NOTE #2
NOTES:1) SIZE 1 - 1/4, 3/8, 1/2 SIZE 2 - 3/8, 1/2, 3/4 SIZE 3 - 3/4, 1
6 PORTS, 1, 3, 5 PORTS2) SIZE 1 - 1/4, 3/8, 1/2 SIZE 2 - 3/8, 1/2, 3/4 SIZE 3 - 1/2, 3/4, 1
2 PORTS, 2, 4 PORTS3) ALL DIMENSIONS ARE IN MILLIMETERS
44
SI UNITFOR DEVICENET SYSTEM
M12 5 PINCONNECTORS
(INPUT NO. 0-3)
M12 5 PINCONNECTOR(INPUT NO. 4-F)
MINI 5 PINCONNECTOR(DEVICENET)
MINI 4 PINCONNECTOR(SOLENOID POWER)
CCCC
20.5
SIZE 2SIZE 3
SIZE 1
SIZE 3SIZE 2SIZE 1
14
U1.5
7368.5
V57.5
234.5189.5
A177.5
142.5125
B119
5671
W43
3530
X25
139
C9
77.552
D50.5
5345
Y42
22
2Z
79.552.548.5
E
64.592
58.5F
99.5146.5168.5
2020
AA14 132.5
BB
10896.5
87G
112123.5
105H
113.5135.5
CC
26.52641
20.5I
5234
J
2820.5
1858.545.5
64.558.530.5
4126
K
5237
L
31.592
M
36
N22
12197.567.5
82.569
O P52
7458.5
Q81
R49 5.5
S
43
T
MANIFOLD DEVICENET
Series VS R 8 Rubber SealS
Subsonic flow: P1+0.1013<1.89(P2+0.1013)
Q=226S √∆P(P2+0.1013)
Sonic flow: P1+0.1013>1.89(P2+0.1013)
Q=113S(P1+0.1013)
Q: Flow rate under standard conditions [l/min(ANR)]S: Effective area (mm2)∆P: Pressure differential (P1-P2) (MPa)P1: Upstream pressure (MPa)P2: Downstream pressure (MPa)* When the air temperatures is different, multiply the flow calculated with
the above formula by the following factor.
Precautions
Quality of Fluid
1. A filter of about 5 µm is adequate.2. Remove contaminants from the system because excess
contaminants cause pneumatic product malfunctions as well as environmental pollution.For added convenience, the use of an auto drain is recommended.
3. When there is a large amount of carbon powder from the compressor, it causes valve malfunction. Please change the compressor oil or install a mist separator.
4. The valve has been lubricated for life at manufacture, and does not require lubrication in service.If a lubricant is used in the system, use turbine oil (ISO VG32).
Solenoid Precautions
1. Ensure that voltage leakage across the coil is as follows.DC coil: No more than 3% of the rated voltageAC coil: No more than 20% of the rated voltage
2. Continuous dutyWhen long term energizing is required, the continuous energizing time should not exceed 30 days.
3. Energization time The double solenoid valve must be energized for at least 0.1 second to ensure proper operation.
Wiring & Light / Surge Voltage Suppressor
Piping
1. Flushing: Thoroughly flush the piping on both inlet and outlet sidesof the valve to remove dust.
2. Mounting position: Mount the double solenoid and 3-position type valves so that the spool valve will be horizontal.
3. Installation in places subject to vibration: Mount the valve so that spool valve will be at right angles to direction of vibration.(Avoid use in places where vibration exceeds 5G.)
4. When 3-position closed center valve is mounted: Check the piping between the valve and cylinder as well as joints for leakage using soapy water. Even slight leakage should be avoided.
5. R(EXH) port piping: Take care that exhaust air is not throttled.(Otherwise, delay in response or cylinder malfunction may result.)
Operation Conditions
Avoid the following locations or environments to prevent valve trouble.If it is unavoidable install a cover, etc. for protection.1. Locations where the ambient temperature exceeds +5~50ºC
range.The metal seal type can be used down to -10ºC, but take care that solidification of contaminants or water freezing does not take place.
2. Locations where valves will be exposed directly to water drops, cutting oil, etc.
3. Locations exposed to direct sunlight.4. Environments causing dewing on valve body or condensation
when there are drastic temperature changes.5. Locations exposed to corrosive gas, chemicals and their solution
or vapor seawater, etc.
How to calculate Flow (At an air temperature 20ºC)
Air Temperature (Cº) -20 -10 0 10 30 40 50 60Factor 1.08 1.06 1.04 1.02 0.98 0.97 0.95 0.94
AC AND 100 VDCAC AND 100 VDC
WITH LIGHTWITH LIGHTTERMINAL no.1 (+)TERMINAL no.1 (+)
SINGLESINGLE
TERMINAL no.2 (-)TERMINAL no.2 (-)
ZNRZNR
WITH LIGHTWITH LIGHT
ZNRZNR
TERMINAL no.2 (-)TERMINAL no.2 (-)
DOUBLEDOUBLE
TERMINAL no.1 (+)no.1 (+)
TERMINAL no.2 (-)TERMINAL no.2 (-)
A SIDEA SIDEREDREDB SIDE TERMINAL no.1 (+)B SIDE TERMINAL no.1 (+)
ZNRZNR
24VDC OR LESS24VDC OR LESS
WITH LIGHTWITH LIGHTTERMINAL no.1 + (-)TERMINAL no.1 + (-)
SINGLESINGLE
TERMINAL no.2 - (+)TERMINAL no.2 - (+)NOTE: NO POLARITYNOTE: NO POLARITY
ZNRZNR
DOUBLEDOUBLE
+ (-)+ (-)
- (+)- (+)
WITH LIGHTWITH LIGHT
ZNRZNR
TERMINAL no.2 - (+)TERMINAL no.2 - (+)NOTE: NO POLARITYNOTE: NO POLARITY
TERMINAL no.1 + (-) A SIDETERMINAL no.1 + (-) A SIDE
- (+)- (+)
+ (-)+ (-)
ZNRZNR
WITH LIGHTWITH LIGHT
B SIDE TERMINAL no.1 + (-)B SIDE TERMINAL no.1 + (-)
TERMINAL no.2 - (+)TERMINAL no.2 - (+)
19
Series VS R 8bS
20
Features / Options
Standard Features
Common EXH Type
All the manifolded valves are supplied andexhausted by the same manifold ports. This isour most popular configuration.
Manifold Option
Terminal Box
• Terminals are provided in the box, permitting connection of conduit piping.
• Simplifies wiring requirements
Interface Options
Individual EXH Spacer
An individual EXH spacer (VV81-R- ) mountedon the manifold block allows each valve toexhaust individually.
Bottom Porting Type (A, B port)
When The application requires bottom porting,either a portion of, or the entire manifold can bepiped with bottom porting.
Individual SUP Spacer
An individual SUP spacer (VV81-P- ) mountedon the manifold block allows each valve toexhaust individually.
SI Unit
With serial interface unit• Solenoid valve wiring reduced considerably.• Applicable to Divice Net and Profi Bus.
Splash Proof
Splash proof manifold conforms to IP65 andNEMA4.• Applicable to all sizes
Expandable ManifoldStacking type manifold can be expanded up tothe recommended number of stations. (Max. of10 stations)
Various porting combinations available tosuit your application.Every manifold block comes standard with sideand bottom ports.
Wide variety of Inerface OptionsIndividual supply/exhoust spacers, interfaceregulators and interface speed controls areavailable to customize your manifold
Interface Regulator
The interface unit is designated to separatelycontrol the pressure of one valve and stillmaintain a common manifold pressure.This unit is available as either a P port regulatoror as an A or B port regulator.
Interface Speed Controls
Cylinder speed can be controlled by throttlingexhaust air.
The manifold Series VV81 have a wide variety of functions and portings, compatible with virtually anyapplication.