cable lists for rnc2600_ru20

8/9/2019 Cable Lists for RNC2600_RU20

http://slidepdf.com/reader/full/cable-lists-for-rnc2600ru20 1/42

DN70539915Issue 2-0

© Nokia Siemens Networks 1 (42)

WCDMA RNC

Cable Lists for RNC2600




2 (42) © Nokia Siemens Networks DN70539915Issue 2-0

The information in this document is subject to change without notice and describes only theproduct defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or

transmitted in any form or means without the prior written permission of Nokia SiemensNetworks. The documentation has been prepared to be used by professional and properlytrained personnel, and the customer assumes full responsibility when using it. Nokia SiemensNetworks welcomes customer comments as part of the process of continuous developmentand improvement of the documentation.

The information or statements given in this documentation concerning the suitability, capacity,or performance of the mentioned hardware or software products are given “as is” and allliability arising in connection with such hardware or software products shall be definedconclusively and finally in a separate agreement between Nokia Siemens Networks and thecustomer. However, Nokia Siemens Networks has made all reasonable efforts to ensure thatthe instructions contained in the document are adequate and free of material errors andomissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks,explain issues which may not be covered by the document.

Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NOEVENT WILL NOKIA SIEMENS NETWORKS BE LIABLE FOR ERRORS IN THISDOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TOSPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES,SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESSINTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THEUSE OF THIS DOCUMENT OR THE INFORMATION IN IT.

This documentation and the product it describes are considered protected by copyrights andother intellectual property rights according to the applicable laws.

The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademarkof Nokia Corporation. Siemens is a registered trademark of Siemens AG.

Other product names mentioned in this document may be trademarks of their respectiveowners, and they are mentioned for identification purposes only.

Copyright © Nokia Siemens Networks 2009. All rights reserved.



Contents

DN70539915Issue 2-0


Contents

1 About Cable lists for RNC2600............................................................ 51.1 Related documentation .......................................................................... 5

2 Identifying subracks, connectors and cables.................................... 62.1 Numbering system of the subrack shelves and cable connectors........... 62.1.1 Locking pegs.......................................................................................... 82.2 Categories of cables .............................................................................. 82.2.1 Interconnection cables ........................................................................... 82.2.2 Site cables ............................................................................................. 92.3 Identifying cables ................................................................................. 102.4 Cabling lists ......................................................................................... 12

3 Intracabinet cables for the RNAC cabinet ........................................ 133.1 RNAC power cables............................................................................. 133.2 RNAC control and bus cables .............................................................. 143.3 RNAC LVDS cables ............................................................................. 183.3.1 RNAC synchronization and LVDS cables............................................. 183.4 RNAC LAN cables ............................................................................... 203.5 RNAC alarm and synchronization cables ............................................. 223.6 RNAC protection switch cables ............................................................ 24

4 Intracabinet cables for the RNBC cabinet ........................................ 264.1 RNBC power cables............................................................................. 264.2 RNBC control and bus cables .............................................................. 274.3 RNBC protection switch cables ............................................................ 28

5 Intercabinet cables from RNBC to RNAC ......................................... 315.1 Intercabinet HMS and timing cables..................................................... 315.2 Intercabinet SWU LAN cables .............................................................. 345.3 Intercabinet SFU LVDS lines................................................................ 35

6 Physical cable equipping positions and SW portconnection coordinates..................................................................... 39





Summary of changes

Issue 2-0

Figure 4 Routing of line timing cables CA_060 – CA_062 and CA_067 –CA_069 updated.

Issue 1-0

First issue.




DN70539915Issue 2-0


1 About Cable lists for RNC2600

This document provides a list of all the intercabinet and intracabinetcabling installed in the RNAC and RNBC cabinets in RNC2600.

1.1 Related documentation

Hardware configuration manual

For more detailed information on RNC cabinet mechanics, seeEquipment Lists for RNC2600 .

Engineering description

For basic information on, for example, RNC installation planning, seeWCDMA RNC Engineering Description.

Installation manual

For detailed information on RNC hardware installation, see Installing theMGW and RNC .




DN70539915Issue 2-0


IPA2800 RNC / MGW cabinet,

seen from the front

Slot position number

CA_020 OMU 0 1.0B 16.4X DU 0-0 1.0B 17.3H CJA002 SCSI bus 0

CA_021 OMU 0 1.0B 16.5D DU 0-0 1.0B 17.3O CJB002 SCSI bus 0

FU Connector FU Connector Type Use

Equip No. CABLE FROM CABLE TO

Connector Type ACE

1.0B 16.4X

1 2 3F = FRONTB = BACK 4

DN05158647

Subrack in position 1 seen from the rear

A

C

E

G

J

L

N

P

R

T

V

X

Z

Z ABCDEF

3

1

2

3

4

5

B

A

B

A

B

Connector Type BDF

B

D

F

H

K

M

O

Q

S

U

Y

Z ABCDEF

4

12345678910111213141516171819

2

Note

1

Figure 1 Notations used in the cabling lists





2.1.1 Locking pegs

Each connector is provided with locking devices (for example locking

pegs or screws) that fasten the cable connector securely to the subrack.The connector locking pegs are placed in the same positions in eachsubrack type, regardless of the subrack's position in a given cabinet. If the subrack includes supplementary locking pegs, they can be used asspare parts.

1

2

3

4

5

12345678910111213141516171819

XXX

X

XXXXX

XXX

XXXXXX

XXXXX

XXXXX

XXXXX

XX

X

X

X

XXXXX

XXXXX

XXXX

XXXXX

XXXXX

XXXXX

X XX

X XXXXX

X

XXX X

XX

XXX

XXX

XX

X X X X

XXXXX

XXXXX

XXXXX

XXXXXXXXXX

XXXXX

XXXXX

XX

XXXXXXXXXX

XXXXXXXXXX

XXXXXXXXXX

XXXXX

XXXXX

XX

X

XXXXX

XXX

XX

XXXXX

XX

Figure 2 Locking pegs’ positions

2.2 Categories of cables

The cabling of an exchange consists of interconnection cables(intermediate cables) and site cables (outgoing cables) as describedbelow.

2.2.1 Interconnection cables

The interconnection cables comprise all the cables inside each cabinetand between the cabinets which form a single exchange. The




DN70539915Issue 2-0


interconnection cables are cut to length and equipped with connectors.They include:

Power distribution cables

ATM connection cables

Hardware Management Bus cables

Synchronization and timing cables

SCSI cables between storage units and their master units

LAN/Ethernet cables

Intracabinet cables

The interconnection cables between different subracks located in the

same cabinet run from one subrack to another along the walls andcabling shelves of the cabinet. These cables are delivered completelyinstalled in the cabinets.

Intercabinet cables

The interconnection cables running between different cabinets are leddirectly from one cabinet to another on cable shelves located behind thecabinets. These cables must be installed at the site. The interconnectioncables are delivered as prefabricated cable sets.

2.2.2 Site cables

The site (outgoing) cables are all the cables that leave the exchange.They include:

Trunk circuit cables from the network interfaces

Power supply cables

Grounding cables

I/O cables

TCP/IP cables to the Network Management system

The site cables are connected directly to the plug-in units, or to the backinterface units located at the rear of the cabinets. These cables must beinstalled at the site.

The site cables can be routed to the environment through the opening atthe bottom (raised floor installations) or top plate (normal installation) of the EC216. These cables must be installed at the site.





All the cables entering the cabinet(s), except for the DC power feedcables, must have protective wires which are grounded to the frame of the exchange at the connectors in the cabling cabinets.

The site cables are not delivered in sets and vary in length depending onthe delivery. They must be ordered separately and are designed for each delivery. They are not included in the standard documentation.

2.3 Identifying cables

The equipping reference is located on the Cable Identification Label (b inFigure 3 Example of the marking system for the cables below).

The first part of the equipping reference specifies the cable list where thecable is mentioned. The second part gives the sequence number withinthat list.

The equipping reference of the cables is based on the cabinet (type)name in which the cable is connected. There are two main groups:

1. Cables whose both ends are connected in the same cabinet(intracabinet cables).

The equipping information is expressed: [Cabinet type_sequencenumber].”CA_123”. There may be several identical cables of this type ina single Network Element, but only one within the same cabinet.

2. Cables which originate from one cabinet and end in another (intercabinet cables).

The equipping information is expressed: [Cabinet type, cabinet index_ sequence number].”CBn_123”. There may be only one of eachindividual cable of this type in a single Network Element.

All intercabinet cables connect from RNBC to RNAC.

The cabinet, where the cable starts in, determines the [cabinet type,cabinet index] part of the equipping reference.




DN70539915Issue 2-0


DN99632985

b) Cable identification label

) A letter 'C' after the number indicates centimetres (cm) instead of decimetres (dm).

Example

a) Equipping number of cable, e.g.

Sequential number

ITEM NAME:CJA002 LOT ID: 3G9912

Alias name

Fixed length (dm)Item identifier

Separators

Factory symbol

Year / Week

Interchangeability / version

C19179 .......... A01

CA-020

CA_020

a)

b)

CA_020

a)

Figure 3 Example of the marking system for the cables




DN70539915Issue 2-0


3 Intracabinet cables for the RNACcabinet

This chapter presents the intracabinet cabling for the RNAC cabinet inRNC2600.

Single cabinet figures show the RNAC cabinet. Two-cabinet figuresshow the RNAC and RNBC cabinets from left to right, unless otherwiseindicated.

Tip

The lengths of intracabinet cables in deliveries may be different fromthose given in this document.

3.1 RNAC power cables

Table 2 RNAC CPD120-A power cables

CABLE FROM CABLE TO

Equip.No

C a b i n e t

FU Position

C a b i n e t

FU Position Type Use Note

CA_001 A CPD120 UB2 0.10B P1 A PD30 0 1.0B 10_PP2 CVXB004 POWER



CA_004 A CPD120 UB1 0.0B P2 A PD30 1 20B 10_PP1 CVXB015 POWER









3.2 RNAC control and bus cables

Table 3 RNAC control cables

CABLE FROM CABLE TO

Equip.No

C a b i n e t

FU Position

C a b i n e t


CA_010 A FTRA 1 1.0B A PD30 0 1.0B 10_P1 CXVB18C CONTROL




Table 4 RNAC OMU and OMS SCSI bus 0/1 cables

CABLE FROM CABLE TO

Equip.No

C a b i n e t

FU Position

C a b i n e t


CA_075 A OMU 0 1.0B 16.4P A WDU 0 (OMU) 1.0B 14.2P CHS006 SCSI bus 0

CA_076 A OMU 0 1.0B 16.4V A WDU 0 (OMU) 1.0B 14.2V CHS006 SCSI bus 0

CA_077 A OMU 0 1.0B 16.5B A WDU 0 (OMU) 1.0B 14.3B CHS006 SCSI bus 0

CA_078 A WDU 0 (OMU) 1.0B 14.3H A OMU 1 2.0B 16.4P CHS012 SCSI bus 0CA_079 A WDU 0 (OMU) 1.0B 14.3O A OMU 1 2.0B 16.4V CHS012 SCSI bus 0

CA_080 A WDU 0 (OMU) 1.0B 14.3U A OMU 1 2.0B 16.5B CHS012 SCSI bus 0

CA_081 A OMS 1.0B 6.4P A HDD 0 (OMS) 1.0B 14.4P CHS005 SCSI bus 0

CA_082 A OMS 1.0B 6.4V A HDD 0 (OMS) 1.0B 14.4V CHS005 SCSI bus 0

CA_083 A OMS 1.0B 6.5B A HDD 0 (OMS) 1.0B 14.5B CHS005 SCSI bus 0

CA_084 A OMU 0 1.0B 16.5H A WDU 1 (OMU) 2.0B 14.2P CHS012 SCSI bus 1

CA_085 A OMU 0 1.0B 16.5O A WDU 1 (OMU) 2.0B 14.2V CHS012 SCSI bus 1

CA_086 A OMU 0 1.0B 16.5U A WDU 1 (OMU) 2.0B 14.3B CHS012 SCSI bus 1

CA_087 A OMU 1 2.0B 16.5H A WDU 1 (OMU) 2.0B 14.3H CHS006 SCSI bus 1

CA_088 A OMU 1 2.0B 16.5O A WDU 1 (OMU) 2.0B 14.3O CHS006 SCSI bus 1

CA_089 A OMU 1 2.0B 16.5U A WDU 1 (OMU) 2.0B 14.3U CHS006 SCSI bus 1

CA_090 A OMS 1.0B 6.5H A HDD 1 (OMS) 2.0B 14.4P CHS012 SCSI bus 1

CA_091 A OMS 1.0B 6.5O A HDD 1 (OMS) 2.0B 14.4V CHS012 SCSI bus 1

CA_092 A OMS 1.0B 6.5U A HDD 1 (OMS) 2.0B 14.5B CHS012 SCSI bus 1




DN70539915Issue 2-0


Table 5 RNAC HMS bus cables

CABLE FROM CABLE TO

Equip.No

C a b i n e t

FU Position

C a b i n e t


CA_040 A OMU 0 1.0B 16.3F A TBU 0 1.0B 19.2A CHZ006 HMS bus 0

CA_041 A OMU 1 2.0B 16.3F A TBU 0 2.0B 19.2A CHZ006 HMS bus 0

CA_042 A TBU 0 1.0B 19.2B A TBU 0 2.0B 19.2B CHZ011 HMS bus 0

CA_043 A TBU 0 2.0B 19.2C A TBU 0 3.0B 19.2A CHZ012 HMS bus 0

CA_044 A TBU 0 3.0B 19.2B A TBU 0 4.0B 19.2A CHZ012 HMS bus 0

CA_046 A TBU 0 4.0B 19.2C A TBU 0 4.0B 19.2D CHZ001 HMS bus 0term.

CA_047 A OMU 0 1.0B 16.3G A TBU 1 1.0B 38.5A CHZ005 HMS bus 1

CA_048 A OMU 1 2.0B 16.3G A TBU 1 2.0B 38.5A CHZ005 HMS bus 1

CA_049 A TBU 1 1.0B 38.5B A TBU 1 2.0B 38.5B CHZ009 HMS bus 1

CA_050 A TBU 1 2.0B 38.5C A TBU 1 3.0B 38.5A CHZ010 HMS bus 1

CA_051 A TBU 1 3.0B 38.5B A TBU 1 4.0B 38.5A CHZ010 HMS bus 1

CA_053 A TBU 1 4.0B 38.5C A TBU 1 4.0B 38.5D CHZ001 HMS bus1term.

CA_054 A TBU 0 1.0B 19.1Z A TBU 1 2.0B 38.4Z CHZS010 HMS bus

Note: For information on terminating cables, see Table 19 Intercabinet HMS and timing cables from RNBC to RNAC.

Table 6 RNAC timing bus cables

CABLE FROM CABLE TO

Equip.No

C a b i n e t

FU Position

C a b i n e t


CA_063 A TBU 0 1.0B 19.2M A TBU 0 2.0B 19.2K CHZ011 TIMING bus 0

CA_064 A TBU 0 2.0B 19.2L A TBU 0 3.0B 19.2K CHZ012 TIMING bus 0


CA_066 A TBU 0 4.0B 19.2L A TBU 0 4.0B 19.2E CHZ001 TIMING bus 0term.

CA_070 A TBU 1 2.0B 38.5M A TBU 1 1.0B 38.5K CHZ009 TIMING bus 1



CA_073 A TBU 1 4.0B 38.5L A TBU 1 4.0B 38.5E CHZ001 TIMING bus 1term.





Table 7 RNAC default line timing cables

CABLE FROM CABLE TO

Equip.No

C a b i n e t

FU Position

C a b i n e t


CA_060 A NPS1/NPS1P 2 3.0B 16.4V A TBU 0 1.0B 19.2G CHZ028 TIMING ref. 1 1) Default linetiming

CA_061 A NPS1/NPS1P 3 4.0B 16.4V A TBU 0 1.0B 19.2H CHZ028 TIMING ref. 2 1) Default linetiming

CA_062 A NPS1/NPS1P 4 3.0B 18.4V A T BU 0 1.0B 19.2J CHZ028 TIMING ref. 3 1) Default linetiming

CA_067 A NPS1/NPS1P 2 3.0B 16.4X A TBU 1 2.0B 38.5G CHZ028 TIMING ref. 1 1) Default linetiming

CA_068 A NPS1/NPS1P 3 4.0B 16.4X A TBU 1 2.0B 38.5H CHZ028 TIMING ref. 2 1) Default linetiming

CA_069 A NPS1/NPS1P 4 3.0B 18.4X A T BU 1 2.0B 38.5J CHZ028 TIMING ref. 3 1) Default line

timing1) These cables must be installed last. They are bundled separately from other cables for easier modification.




DN70539915Issue 2-0


Figure 4 Routing of line timing cables CA_060 – CA_062 and CA_067 –CA_069





3.3 RNAC LVDS cables

3.3.1 RNAC synchronization and LVDS cables

Table 8 RNAC SFU LVDS cables

CABLE FROM CABLE TO

Equip.No

C a b i n e t

FU Position

C a b i n e t


CA_200 A SFU 0 /

BISFD

1.0B 1.B00 A MXU 0 /

BISFB

1.0B 9.B00 CSB007 LVDS lines 3)

CA_201 A SFU 0 /BISFD

1.0B 1.B01 A MXU 1 /BISFB

















CA_207 A SFU 0 /

BISFD

1.0B 1.B07 A MXU 7 /

BISFB


CA_210 A SFU 0 /BISFA

1.0B 2.B16 A NPGE/NPGEP 0 /NP1S/NPS1P 0

BISFC



1.0B 2.B17 A NPGE/NPGEP 1 /NP1S/NPS1P 1BISFC



1.0B 2.B18 A NPGE/NPGEP 2

BISFC

1.0B 18. B00 CSB009 LVDS lines 1) 3) Default:connected



BISFC

2.0B 18. B00 CSB014 LVDS lines 2) 3) Default:connected


1.0B 2.B20 A NPGE/NPGEP 4 /NP1S/NPS1P 2

BISFC






1.0B 2.B22 A NPGE/NPGEP 6 /NP1S/NPS1P 4 /BISFC








DN70539915Issue 2-0


CABLE FROM CABLE TO

Equip.No

C

a b i n e t

FU Position

C

a b i n e t



2.0B 1. B00 A MXU 0 /BISFB

















CA_226 A SFU 1 /

BISFD

2.0B 1. B06 A MXU 6 /

BISFB






2.0B 2. B16 A NPGE/NPGEP 0 /NP1S/NPS1P 0 /BISFC



2.0B 2. B17 A NPGE/NPGEP 1 /NP1S/NPS1P 1BISFC




BISFC

1.0B 18.B02 CSB015 LVDS lines 1) 3) Default:connected



BISFC

2.0B 18.B02 CSB008 LVDS lines 2) 3) Default:connected








2.0B 2. B22 A NPGE/NPGEP 6 /NP1S/NPS1P 4 /BISFC





1) Default: Connected when NPGE/NPGEP 2 is in configuration.

Optional: Removed when NPS1/NPS1P 0 is in configuration.

2) Default: Connected when NPGE/NPGEP 3 is in configuration.

Optional: Removed when NPS1/NPS1P 1 is in configuration.

3) Cables are connected after the BISFA, BISFB, BISFC and BISFD back interface units have been installed. Insert the back interface unitcarefully. Check that the locking screws are closed properly, and that the back interface unit is in its place.





Table 9 TSS3 synchronization cable

CABLE FROM CABLE TO

Equip.No

C a b i n e t

FU Position

C a b i n e t


CA_305 A TSS3 1.0B 19.1X A TSS3 2.0B 38.4X CHE011 Sync

3.4 RNAC LAN cables

Table 10 RNAC SWU (ESA24) LAN cables with one SWU pair (SWU0/1)

CABLE FROM CABLE TO

Equip.No

C a b i n e t

FU Position

C a b i n e t


CA_132 A SWU 0 1.0B 5.4G A OMS 1.0B 6.3B CHES006 LAN

CA_131 A SWU 0 1.0B 5.4E A OMU 1 2.0B 16.3B CHES013 LAN

CA_130 A SWU 0 1.0B 5.4C A OMU 0 1.0B 16.3B CHES006 LAN

CA_145 A SWU 0 1.0B 5.5D A NPGE/NPGEP 7 /

NPS1/NPS1P 5BISFC

4.0B 17.4E CIBS027 LAN

CA_144 A SWU 0 1.0B 5.5B A NPGE/NPGEP 6 /

NPS1/NPS1P 4BISFC


CA_143 A SWU 0 1.0B 5.4Z A NPGE/NPGEP 5 /

NPS1/NPS1P 3BISFC


CA_172 A SWU 0 1.0B 5.4X A NPGE/NPGEP 4 /

NPS1/NPS1P 2BISFC


CA_147 A SWU 0 1.0B 5.4V A NPGE/NPGEP 3BISFC

2.0B 18.4E CIBS013 LAN 2) Default:connected

CA_146 A SWU 0 1.0B 5.4T A NPGE/NPGEP 2BISFC

1.0B 18.4E CIBS007 LAN 1) Default:connected

CA_171 A SWU 0 1.0B 5.4R A NPGE/NPGEP 1 /

NPS1/NPS1P 1BISFC


CA_140 A SWU 0 1.0B 5.4P A NPGE/NPGEP 0 /

NPS1/NPS1P 0

BISFC





DN70539915Issue 2-0


CABLE FROM CABLE TO

Equip.No

C

a b i n e t

FU Position

C

a b i n e t


CA_134 A SWU 1 2.0B 5.4J A SWU 0 1.0B 5.4J CHES017 LAN 3) Default:Notconnected

CA_133 A SWU 1 2.0B 5.4G A OMS 1.0B 6.3D CHES016 LAN

CA_139 A SWU 1 2.0B 5.4E A OMU 1 2.0B 16.3D CHES007 LAN

CA_138 A SWU 1 2.0B 5.4C A OMU 0 1.0B 16.3D CHES014 LAN

CA_155 A SWU 1 2.0B 5.5D A NPGE/NPGEP 7 /

NPS1/NPS1P 5BISFC

4.0B 17.4G CIBS021 LAN

CA_154 A SWU 1 2.0B 5.5B A NPGE/NPGEP 6 /

NPS1/NPS1P 4BISFC


CA_153 A SWU 1 2.0B 5.4Z A NPGE/NPGEP 5 /

NPS1/NPS1P 3BISFC


CA_152 A SWU 1 2.0B 5.4X A NPGE/NPGEP 4 /

NPS1/NPS1P 2BISFC


CA_149 A SWU 1 2.0B 5.4V A NPGE/NPGEP 3BISFC

2.0B 18.4G CIBS007 LAN 2) Default:connected

CA_148 A SWU 1 2.0B 5.4T A NPGE/NPGEP 2BISFC

1.0B 18.4G CIBS013 LAN 1) Default:connected

CA_151 A SWU 1 2.0B 5.4R A NPGE/NPGEP 1 /

NPS1/NPS1P 1BISFC


CA_150 A SWU 1 2.0B 5.4P A NPGE/NPGEP 0 /

NPS1/NPS1P 0BISFC


1) Default: Connected at factory. Connected when NPGE/NPGEP 2 is in configuration.Optional: Removed when NPS1/NPS1P 0 is in configuration.

2) Default: Connected at factory. Connected when NPGE/NPGEP 3 is in configuration.Optional: Removed when NPS1/NPS1P 1 is in configuration.

3) Default: Redundancy cable is not connected at the factory.Optional: The cable is connected only when the Rabid Spanning Tree Protocol (RSTP) is enabled in the LAN sub network. Before

connecting the cable, activate STP/RSTP/MSTP according to the planned resiliency method.





Table 11 Address setting modules

Position ID Name Use Note

1.0B 5.1S C108585 ADMOD01 SW U Cabinet address setting module1.0B 5.1U C108585 ADMOD01 SW U Subrack address setting module

2.0B 5.1S C108585 ADMOD01 SW U Cabinet address setting module

2.0B 5.1U C108690 ADMOD02 SW U Subrack address setting module

3.5 RNAC alarm and synchronization cables

Table 12 RNAC alarm and synchronization cables to rear panels CPSY- A, CPSY-B and CPAL-A

CABLE FROM CABLE TO

Equip.No

C a b i n e t

FU Position

C a b i n e t


CA_300 A CPAL-A 2.0B 1.A A EHU 3.0B 5.4G CJA016 ALARM

CA_301 A CPAL-A 2.0B 1.G A EHU 3.0B 5.4P CHQ016 ALARM

CA_302 A CPAL-A 2.0B 1.P A EHU 3.0B 5.4X CHM016 ALARM

CA_015 A CAIND 0.0B 1 A EHU 3.0B 5.4E CID030 ALARM

1.0B 1.C 1) Default1.0B 1.G 2) Optional

1.0B 1.L 3) Optional

CA_303 A CPSY-A

1.0B 1.P

A TSS3 1.0B 19.1V CHE010 SYNC

4) Optional

1.10B 1.A 1) Default

1.10B 1.E 2) Optional

1.10B 1.J 3) Optional

CA_304 A CPSY-B

1.10B 1.N

A TSS3 2.0B 38.4V CHE010 SYNC

4) Optional

CA_298 A SWU 0 1.0B 5.5Y A CPSY-A 1.0B 1.1V CHE012 ETHERNET

CA_299 A CPSY-A 1.0B 1.1R A CPSY-B 1.10B 1.1T CHE005 SYNC

CA_297 A CPSY-A 1.0B 1.1T A CPSY-B 1.10B 1.1R CHE005 SYNC

1) BNC IN, BNC OUT, Default2) BNC IN, RJ 45 OUT, Optional3) RJ 45 IN, BNC OUT, Optional4) RJ 45 IN, RJ 45 OUT, Optional




DN70539915Issue 2-0


1 9 18 1 7 1 6 15 1 4 1 3 12 1 1 1 0 9 8 7 6 5 4 3 2 1

38

1 9 18 1 7 1 6 15 1 4 1 3 12 1 1 1 0 9 8 7 6 5 4 3 2 1

38

1 9 18 1 7 1 6 15 1 4 1 3 12 1 1 1 0 9 8 7 6 5 4 3 2 1

38

1 9 18 1 7 1 6 15 1 4 1 3 12 1 1 1 0 9 8 7 6 5 4 3 2 1

38

CPSY-A

CPAL-A

CPSY-B

DN05160803

Figure 5 CPSY-A, CPSY-B and CPAL-A panel positions in RNAC





3.6 RNAC protection switch cables

Table 13 MSP1+1, PIU_OK, PAIR_OK and switchover cables for RNAC

CABLE FROM CABLE TO

Equip.No

C a b i n e t

FU Position

C a b i n e t


CA_370 A NPS1P 0 1.0B 18.4T A NPS1P 1 2.0B 18.4T CIBS010 MSP1+1ProtectionSwitch

1) Default:notconnected

CA_375 A NPS1P 0 1.0B 18.4R A NPS1P 1 2.0B 18.4R CIBS010 LVDS linesProtectionSwitch


CA_374 A NPS1P 0 1.0B 18.4P A NPS1P 1 2.0B 18.4P CIBS010 LVDS linesProtectionSwitch


CA_165 A NPGEP 2 1.0B 18.4L A NPGEP 3 2.0B 18.4L CHZS010 Switchover

NPS1P 0 NPS1P 1 MSP1+1ProtectionSwitch

CA_373 A

NPGEP 2

1.0B 18.4J A

NPGEP 3

2.0B 18.4J CIBS010

PIU_OK/PAIR_OK

CA_372 A NPS1P 0 1.0B 18.4G A NPS1P 1 2.0B 18.4G CIBS010 MSP1+1ProtectionSwitch


CA_371 A NPS1P 0 1.0B 18.4E A NPS1P 1 2.0B 18.4E CIBS010 MSP1+1ProtectionSwitch


CA_163 A NPGEP 0 /

NPS1P 0

1.0B 17. 4L A NPGEP 1 /

NPS1P 1

2.0B 17.4L CHZS010 Switchover

CA_164 A NPGEP 0 /

NPS1P 0

1.0B 17.4K A NPGEP 1 /

NPS1P 1

2.0B 17.4K CHZS010 PIU_OK/PAIR_OK

1) Default: Not connected at the factory. The cable is tied to the SRB1-C side plate near these equipping positions. Optional: Cables areconnected to these equipping positions when NPS1P 0 and NPS1P 1 pair are equipped.




CA_351 A NPS1P 2 3.0B 16.4J A NPS1P 3 4.0B 16.4J CIBS010 MSP1+1ProtectionSwitch






DN70539915Issue 2-0


CABLE FROM CABLE TO

Equip.No

C

a b i n e t

FU Position

C

a b i n e t


CA_161 A NPGEP 4 /

NPS1P 2

3.0B 15.4L A NPGEP 5 /

NPS1P 3


CA_162 A NPGEP 4 /

NPS1P 2

3.0B 15.4K A NPGEP 5 /

NPS1P 3





CA_353 A NPS1P 4 3.0B 18.4J A NPS1P 5 4.0B 18.4J CIBS010 MSP1+1ProtectionSwitch



CA_156 A NPGEP 6 /

NPS1P 4

3.0B 17.4L A NPGEP 7 /

NPS1P 5


CA_157 A NPGEP 6 /

NPS1P 4

3.0B 17.4K A NPGEP 7 /

NPS1P 5






4 Intracabinet cables for the RNBCcabinet

This chapter presents the intracabinet cabling for the RNBC cabinet inRNC2600.

Tip

The lengths of intracabinet cables in deliveries may be different thanthose given in this document.

4.1 RNBC power cables

Table 14 RNBC CPD120-A power cables

CABLE FROM CABLE TO

Equip.No

C a b i n e t

FU Position

C a b i n e t


CB_001 B CPD120 UB2 0.10B P1 B PD30 0 1.0B 10_PP2 CVXB004 POWER











DN70539915Issue 2-0


4.2 RNBC control and bus cables

Table 15 RNBC control cables

CABLE FROM CABLE TO

Equip.No

C a b i n e t

FU Position

C a b i n e t


CB_010 B FTRA 1 1.0B B PD30 0 1.0B 10_P1 CXVB18C CONTROL




Table 16 RNBC HMS bus cables

CABLE FROM CABLE TO

Equip.No

C a b i n e t

FU Position

C a b i n e t


CB_020 B TBU 0 1.0B 19.2B B TBU 0 2.0B 19.2A CHZ011 HMS bus 0



CB_023 B TBU 0 4.0B 19.2C B TBU 0 4.0B 19.2D CHZ001 HMS bus 0term




CB_027 B TBU 1 4.0B 38.5C B TBU 1 4.0B 38.5D CHZ001 HMS bus 1term

Table 17 RNBC timing bus cables

CABLE FROM CABLE TO

Equip.No

C a b i n e t

FU Position

C a b i n e t


CB_030 B TBU 0 1.0B 19.2L B TBU 0 2.0B 19.2K CHZ011 TIMING bus 0






CABLE FROM CABLE TO

Equip.No

C

a b i n e t

FU Position

C

a b i n e t



CB_033 B TBU 0 4.0B 19.2L B TBU 0 4.0B 19.2E CHZ001 TIMING bus 0term




CB_037 B TBU 1 4.0B 38.5L B TBU 1 4.0B 38.5E CHZ001 TIMING bus 1term

4.3 RNBC protection switch cables

Table 18 RNBC protection switch cables

CABLE FROM CABLE TO

Equip.No

C a b i n e t

FU Position

C a b i n e t


CB_354 B NPS1P 6 1.0B 16.4T B NPS1P 7 2.0B 16.4T CIBS013 MSP1+1ProtectionSwitch

CB_371 B NPS1P 6 1.0B 16.4E B NPS1P 7 2.0B 16.4E CIBS013 LVDS linesProtectionSwitch

CB_370 B NPS1P 6 1.0B 16.4J B NPS1P 7 2.0B 16.4J CIBS013 LVDS linesProtectionSwitch

CB_357 B NPS1P 6 1.0B 16.4R B NPS1P 7 2.0B 16.4R CIBS013 MSP1+1ProtectionSwitch

CB_356 B NPS1P 6 1.0B 16.4P B NPS1P 7 2.0B 16.4P CIBS013 MSP1+1ProtectionSwitch

CB_355 B NPS1P 6 1.0B 16.4G B NPS1P 7 2.0B 16.4G CIBS013 MSP1+1ProtectionSwitch





DN70539915Issue 2-0


CABLE FROM CABLE TO

Equip.No

C

a b i n e t

FU Position

C

a b i n e t














CB_377 B NPS1P 12 3.0B 18.4E B NPS1P 13 4.0B 18.4E CIBS013 LVDS lines

ProtectionSwitch








CABLE FROM CABLE TO

Equip.No

C

a b i n e t

FU Position

C

a b i n e t



CB_380 B NPGEP 8 /

NPS1P 6

1.0B 15.4K B NPGEP 9 /

NPS1P 7

2.0B 15.4K CHZS015 PIU_OK

PAIR_OK

CB_381 B NPGEP 10 /

NPS1P 8

1.0B 17.4K B NPGEP 11 /

NPS1P 9


PAIR_OK

CB_382 B NPGEP 12 /

NPS1P 10

3.0B 15.4K B NPGEP 13 /

NPS1P 11


PAIR_OK

CB_383 B NPGEP 14 /NPS1P 12

3.0B 17.4K B NPGEP 15 /NPS1P 13

4.0B 17.4K CHZS015 PIU_OKPAIR_OK

CB_390 B NPGEP 8 /

NPS1P 6

1.0B 15.4L B NPGEP 9 /

NPS1P 7


CB_391 B NPGEP 10 /

NPS1P 8

1.0B 17.4L B NPGEP 11 /

NPS1P 9


CB_392 B NPGEP 12 /

NPS1P 10

3.0B 15.4L B NPGEP 13 /

NPS1P 11


CB_393 B NPGEP 14 /

NPS1P 12

3.0B 17.4L B NPGEP 15 /

NPS1P 13





DN70539915Issue 2-0


5 Intercabinet cables from RNBC to RNAC

This chapter presents cabling from the RNBC cabinet to the RNACcabinet in RNC2600.

5.1 Intercabinet HMS and timing cables

Table 19 Intercabinet HMS and timing cables from RNBC to RNAC

CABLE FROM CABLE TO

Equip.No

C a

b i n e t

FU Position

C a

b i n e t


A 3.0B 19.2E 1) Timing

bus 0 term.CB0_050

B

TBU 0

1.0B 19.2K

A TBU 0 1.0B 19.2N CHZ020 TIMING bus 0

2) Timing

bus 0 to

B-cabinet

A 3.0B 38.5E 1) Timing bus1 term.CB0_051

B

TBU 1

1.0B 38.5K

A TBU 1 2.0B 38.5N CHZ020 TIMING bus 1

2) Timing

bus 1 to

B-cabinet

A 3.0B 19.2D 1) HMS term.

CB0_040 B TBU 0 1.0B 19.2A A TBU 0 1.0B 19.2C CHZ020 HMS bus 0 2) HMS to

B-cabinet

A 3.0B 38.5D 1) HMS term.

CB0_041 B TBU 1 1.0B 38.5A A TBU 1 1.0B 38.5C CHZ020 HMS bus 1 2) HMS to

B-cabinet





CABLE FROM CABLE TO

Equip.No

C

a b i n e t

FU Position

C

a b i n e t


1) Default: Connected at factory. Connect the terminating cables to subrack 3 if RNBC cabinet is not in the configuration.

2) Optional: If RNBC cabinet is in the configuration, these cables are moved to RNBC subrack 1.

Note that if there is no RNBC cabinet in the configuration, all of these cables are in the RNAC cabinet.




DN70539915Issue 2-0


1 9 1 8 1 7 1 6 1 5 1 4 1 3 1 2 1 1 1 0 9 8 7 6 5 4 3 2 1

38

1 9 1 8 1 7 1 6 1 5 1 4 1 3 1 2 1 1 1 0 9 8 7 6 5 4 3 2 1

38

1 9 1 8 1 7 1 6 1 5 1 4 1 3 1 2 1 1 1 0 9 8 7 6 5 4 3 2 1

38

1 9 1 8 1 7 1 6 1 5 1 4 1 3 1 2 1 1 1 0 9 8 7 6 5 4 3 2 1

38

1 9 1 8 1 7 1 6 1 5 1 4 1 3 1 2 1 1 1 0 9 8 7 6 5 4 3 2 1

38

1 9 1 8 1 7 1 6 1 5 1 4 1 3 1 2 1 1 1 0 9 8 7 6 5 4 3 2 1

38

1 9 1 8 1 7 1 6 1 5 1 4 1 3 1 2 1 1 1 0 9 8 7 6 5 4 3 2 1

38

1 9 1 8 1 7 1 6 1 5 1 4 1 3 1 2 1 1 1 0 9 8 7 6 5 4 3 2 1

38

RNBC RNAC

DN05160893

= HMS bus 0 / Timing bus 0= HMS bus 1 / Timing bus 1

Figure 6 Routing of HMS cables CB0_040 – CB0_041 and timing cablesCB0_050 – CB0_051





5.2 Intercabinet SWU LAN cables

Table 20 Intercabinet SWU LAN cables

CABLE FROM CABLE TO

Equip.No

C a b i n e t

FU Position

C a b i n e t


CB0_107 B NPGE/NPGEP 15 /

NPS1/NPS1P 13BISFC

4.0B 17.4E A SWU 0 1.0B 5.5U CIBS027 LAN 1)


NPS1/NPS1P 12BISFC

3.0B 17.4E A SWU 0 1.0B 5.5S CIBS021 LAN 1)


NPS1/NPS1P 11BISFC

4.0B 15.4E A SWU 0 1.0B 5.5Q CIBS027 LAN 1)


NPS1/NPS1P 10BISFC

3.0B 15.4E A SWU 0 1.0B 5.5O CIBS021 LAN 1)


NPS1/NPS1P 9BISFC

2.0B 17.4E A SWU 0 1.0B 5.5M CIBS018 LAN 1)


NPS1/NPS1P 8BISFC

1.0B 17.4E A SWU 0 1.0B 5.5K CIBS014 LAN 1)


NPS1/NPS1P 7BISFC

2.0B 15.4E A SWU 0 1.0B 5.5H CIBS018 LAN 1)


NPS1/NPS1P 6BISFC

1.0B 15.4E A SWU 0 1.0B 5.5F CIBS014 LAN 1)


NPS1/NPS1P 13BISFC

4.0B 17.4G A SWU 1 2.0B 5.5U CIBS021 LAN 1)


NPS1/NPS1P 12BISFC

3.0B 17.4G A SWU 1 2.0B 5.5S CIBS018 LAN 1)


NPS1/NPS1P 11BISFC

4.0B 15.4G A SWU 1 2.0B 5.5Q CIBS021 LAN 1)


NPS1/NPS1P 10

3.0B 15.4G A SWU 1 2.0B 5.5O CIBS018 LAN 1)


NPS1/NPS1P 9BISFC

2.0B 17.4G A SWU 1 2.0B 5.5M CIBS014 LAN 1)


NPS1/NPS1P 8BISFC

1.0B 17.4G A SWU 1 2.0B 5.5K CIBS018 LAN 1)




DN70539915Issue 2-0


CABLE FROM CABLE TO

Equip.No

C

a b i n e t

FU Position

C

a b i n e t



NPS1/NPS1P 7BISFC

2.0B 15.4G A SWU 1 2.0B 5.5H CIBS014 LAN 1)


NPS1/NPS1P 6BISFC

1.0B 15.4G A SWU 1 2.0B 5.5F CIBS018 LAN 1)

1) Cables are connected before the BISFC back interface unit has been installed.

5.3 Intercabinet SFU LVDS lines

Table 21 Intercabinet SFU LVDS cables

CABLE FROM CABLE TO

Equip.No

C a b i n e t

FU Position

C a b i n e t


CB0_200 B MXU 8 /

BISFB

1.0B 9.B00 A SFU 0 /

BISFA


CB0_201 B MXU 9 /

BISFB

1.0B 11.B00 A SFU 0 /

BISFA


CB0_202 B MXU 10 /

BISFB

2.0B 9.B00 A SFU 0 /

BISFA


CB0_203 B MXU 11 /

BISFB

2.0B 11.B00 A SFU 0 /

BISFA


CB0_204 B MXU 12 /

BISFB

3.0B 9.B00 A SFU 0 /

BISFA


CB0_205 B MXU13 /

BISFB

3.0B 11.B00 A SFU 0 /

BISFA


CB0_206 B MXU 14 /

BISFB

4.0B 9.B00 A SFU 0 /

BISFA


CB0_207 B MXU 15 /

BISFB

4.0B 11.B00 A SFU 0 /

BISFA



NPS1/NPS1P 6

BISFC

1.0B 15.B00 A SFU 0 /

BISFA



NPS1/NPS1P 7

BISFC

2.0B 15.B00 A SFU 0 /

BISFA






CABLE FROM CABLE TO

Equip.No

C

a b i n e t

FU Position

C

a b i n e t



NPS1/NPS1P 8

BISFC

1.0B 17.B00 A SFU 0 /

BISFA



NPS1/NPS1P 9

BISFC

2.0B 17.B00 A SFU 0 /

BISFA



NPS1/NPS1P 10

BISFC

3.0B 15.B00 A SFU 0 /

BISFA



NPS1/NPS1P 11

BISFC

4.0B 15.B00 A SFU 0 /

BISFA


CB0_214 B NPGE/NPGEP 14 /NPS1/NPS1P 12

BISFC

3.0B 17.B00 A SFU 0 /BISFA



NPS1/NPS1P 13

BISFC

4.0B 17.B00 A SFU 0 /

BISFA


CB0_216 B MXU 8 /

BISFB

1.0B 9.B02 A SFU 1 /

BISFA


CB0_217 B MXU 9 /

BISFB

1.0B 11.B02 A SFU 1 /

BISFA


CB0_218 B MXU 10 /

BISFB

2.0B 9.B02 A SFU 1 /

BISFA


CB0_219 B MXU 11 /BISFB



CB0_220 B MXU 12 /

BISFB

3.0B 9.B02 A SFU 1 /

BISFA


CB0_221 B MXU 13 /

BISFB

3.0B 11.B02 A SFU 1 /

BISFA


CB0_222 B MXU 14 /

BISFB

4.0B 9.B02 A SFU 1 /

BISFA


CB0_223 B MXU 15 /

BISFB

4.0B 11.B02 A SFU 1 /

BISFA



NPS1/NPS1P 6

BISFC

1.0B 15.B02 A SFU 1 /

BISFA



NPS1/NPS1P 7

BISFC

2.0B 15.B02 A SFU 1 /

BISFA



NPS1/NPS1P 8

BISFC

1.0B 17.B02 A SFU 1 /

BISFA



NPS1/NPS1P 9

BISFC

2.0B 17.B02 A SFU 1 /

BISFA





DN70539915Issue 2-0


CABLE FROM CABLE TO

Equip.No

C

a b i n e t

FU Position

C

a b i n e t



NPS1/NPS1P 10

BISFC

3.0B 15.B02 A SFU 1 /

BISFA


CB0_229 B NPGE/NPGEP 13 /NPS1/NPS1P 11BISFC




NPS1/NPS1P 12

BISFC

3.0B 17.B02 A SFU 1 /

BISFA



NPS1/NPS1P 13

BISFC

4.0B 17.B02 A SFU 1 /

BISFA


1) Cables are connected after the BISFA, BISFB and BISFC back interface units have been installed. Insert the back interface unitcarefully. Check that the locking screws are closed properly, and that the back interface unit is in its place.





1 9 1 8 1 7 1 6 1 5 1 4 1 3 1 2 1 1 1 0 9 8 7 6 5 4 3 2 1

38

1 9 1 8 1 7 1 6 1 5 1 4 1 3 1 2 1 1 1 0 9 8 7 6 5 4 3 2 1

38

1 9 1 8 1 7 1 6 1 5 1 4 1 3 1 2 1 1 1 0 9 8 7 6 5 4 3 2 1

38

1 9 1 8 1 7 1 6 1 5 1 4 1 3 1 2 1 1 1 0 9 8 7 6 5 4 3 2 1

38

1 9 1 8 1 7 1 6 1 5 1 4 1 3 1 2 1 1 1 0 9 8 7 6 5 4 3 2 1

38

1 9 1 8 1 7 1 6 1 5 1 4 1 3 1 2 1 1 1 0 9 8 7 6 5 4 3 2 1

38

1 9 1 8 1 7 1 6 1 5 1 4 1 3 1 2 1 1 1 0 9 8 7 6 5 4 3 2 1

38

1 9 1 8 1 7 1 6 1 5 1 4 1 3 1 2 1 1 1 0 9 8 7 6 5 4 3 2 1

38

RNACRNBC

= LVDS lines / SFU 0

= LVDS lines / SFU 1

DN05160881

Figure 7 Routing of intercabinet LVDS cables CB0_001 – CB0_032




DN70539915Issue 2-0


6 Physical cable equipping positions andSW port connection coordinates

This section shows the physical cable equipping positions in the subrackand the corresponding SW port connection coordinates, used inhardware configuration management.

The cable connection coordinates are needed when creating internalport connections between plug-in units' ports. For more information, seeCreating connection descriptions in Hardware ConfigurationManagement .

For example, for a cable installed in position 1.0B 1.4A, the portconnection coordinate in hardware configuration management (WFcommands) is B76. See also Figure 8 Notations used in table Physical cable equipping positions and corresponding SW port connection

coordinates.





2A

C

E

G

J

L

N

P

R

T

X

Z

B

D

F

H

K

M

O

Q

S

U

3

B1B2

...

B25

B76

1

2

3

4

5

4A

...

...

B26

B51

B101

1 23

B76 4A

DN70206639

S H S H S H SW H SW HW

B1 1A B26 2A B51 3A B76 4A B101 5A

B2 1B B27 2B B52 3B B77 4B B102 5B

Slot position number

Subrack seen from the rear

1

2

3

4

5

12345678910111213141516171819

1

Figure 8 Notations used in table Physical cable equipping positions and corresponding SW port connection coordinates




DN70539915Issue 2-0


Table 22 Physical cable equipping positions and corresponding SW portconnection coordinates

SW H SW HW SW HW SW HW SW HW

B1 1A B26 2A B51 3A B76 4A B101 5A

B2 1B B27 2B B52 3B B77 4B B102 5B

B3 1C B28 2C B53 3C B78 4C B103 5C

B4 1D B29 2D B54 3D B79 4D B104 5D

B5 1E B30 2E B55 3E B80 4E B105 5E

B6 1F B31 2F B56 3F B81 4F B106 5F

B7 1G B32 2G B57 3G B82 4G B107 5G

B8 1H B33 2H B58 3H B83 4H B108 5H

B9 1J B34 2J B59 3J B84 4J B109 5J

B10 1K B35 2K B60 3K B85 4K B110 5K

B11 1L B36 2L B61 3L B86 4L B111 5L

B12 1M B37 2M B62 3M B87 4M B112 5M

B13 1N B38 2N B63 3N B88 4N B113 5N

B14 1O B39 2O B64 3O B89 4O B114 5O

B15 1P B40 2P B65 3P B90 4P B115 5P

B16 1Q B41 2Q B66 3Q B91 4Q B116 5Q

B17 1R B42 2R B67 3R B92 4R B117 5R

B18 1S B43 2S B68 3S B93 4S B118 5S

B19 1T B44 2T B69 3T B94 4T B119 5T

B20 1U B45 2U B70 3U B95 4U B120 5U

B21 1V B46 2V B71 3V B96 4V B121 5V

B22 1W B47 2W B72 3W B97 4W B122 5W

B23 1X B48 2X B73 3X B98 4X B123 5X

B24 1Y B49 2Y B74 3Y B99 4Y B124 5Y

B25 1Z B50 2Z B75 3Z B100 4Z B125 5Z

cable lists for rnc2600_ru20

Documents