c‐bandsuper low noise amplifier w/fault detection · gain (typical) = 28db gain flatness ±0.3db...
TRANSCRIPT
APTW3‐05400590‐1010‐LS‐D4‐FACC‐Band Super Low Noise Amplifier w/Fault Detection
Product Features
Frequency Range = 5.4 to 5.9 GHz
Typical Noise Figure 0.7db Gain (typical) = 28 dB
Gain Flatness ± 0.3dB
+33 dBm (2W) CW Limiter
+5V to +8V 80mA Low DC power consumption
Reverse voltage protection
Form A Current Sensing Fault Alarm
State‐of‐the‐Art PHEMT Technology
MIL‐883, MIL‐45208 construction and reliability
Internal DC regulator
Hermetic seal option
Product Description
The APT3‐05400590‐1010‐LS‐D4‐FAC is a Low Noiseamplifier with super‐low noise figure (<0.9dB, 0.7dBtypical). Lower NF options are also available withcustom flatness, VSWR, P1dB, and outline. An internallimiter at the input offers protection of up to 2W CW ofRF input power over the full band. There is provisionfor a Fault Alarm signal via one of the pins on theexternal MS3112E8‐4P connector (used for power) thatis triggered by a pre‐defined change in current draw.
Application
Receiver Front End Radar Satellite Communication (SATCOM) Microwave Radio System Test Equipment Telemetry
Parameters Unit Minimum Maximum Notes
Operating Temperature (Case)
°C ‐54 +8595% humidity, non‐
condensing
Storage Temperature (Case)
°C ‐54 +11595% humidity, non‐
condensing
RF Input Power dBm
‐33 CW
+47dBm for 0.1uS pulse, 1% D.C
Die Junction Temp (Tj)
°C ‐+150
For GaAs devices
Positive Supply Voltage
V ‐ +16At +V DC terminal
Negative Voltage V ‐ ‐10 Reverse Voltage
Absolute Maximum Ratings*
* Stresses above those listed under "Absolute MaximumRating" may cause permanent damage to the device. Thisis a stress rating only and functional operation of the deviceat these or any other conditions above those indicated inthe operational sections of this specification is not implied.Exposure to absolute maximum rating conditions forextended periods may affect device reliability. AllSTANDARD units are packaged in Aluminum housings thatare layered with electroless Nickel and then plated withGold to eliminate contamination of other adjacentelectronic components.
Typical Key Parameters at 23°C
Parameters Unit Minimum Typical Maximum Notes
Frequency GHz 5.4 ‐ 5.9 Customizable
Gain dB 28 29 30 Customizable
Gain Flatness dB ‐ ±0.3 ±0.5 Customizable
In/Out VSWR ‐ ‐ 1.25 1.40 Customizable
Output P1dB dBm +10 +12 ‐ Customizable
DC Power V@mA +5 +8 +15 @80 mA
Noise Figure dB ‐ 0.7 1.0 Customizable
Outline/Package ‐ ‐ ‐ ‐ D6/H210
Fault Alarm (current sensing)
±5% via MS3112E8‐4P conn.
Max. Input Power dBm ‐ ‐ 2WCW (internal
limiter)
1AmpliTech, Inc. 620 Johnson Avenue Bohemia, NY 11716 Phone: 631‐521‐7831 Fax: 1‐631‐521‐7871
website: http://www.amplitechinc.com
2
Typical Measured Data
Data taken with Agilent N5242 PNA-X Vector Network Analyzer
AmpliTech, Inc. 620 Johnson Avenue Bohemia, NY 11716 Phone: 631‐521‐7831 Fax: 1‐631‐521‐7871website: http://www.amplitechinc.com
DATA TRACE
APTW3‐05400590‐1010‐LS‐D4‐FACC‐Band Super Low Noise Amplifier w/Fault Detection
SAMPLE TABULAR DATA
INTERNAL LNA HOUSING
EXTERNAL LNA HOUSING
EXTERNAL HOUSING
INTERNAL VIEW