c04b pacp esdep wg 7
DESCRIPTION
fffdfdTRANSCRIPT
Previous | Next | Contents
ESDEP WG 7
ELEMENTS
Lecture 7.11: Frames
OBJECTIVE/SCOPE
To introduce the basic ideas of frame behaviour as a prelude to the more detailed description of design in later lectures.
PREREQUISITES
Lectures 1B.7: Introduction to Design of Multi-Storey Buildings
Lectures 6.6: Buckling of Real Structural Elements
Lecture 7.1: Methods of Analysis of Steel Structures
RELATED LECTURES
Lecture 14.2: Analysis of Portal Frames: Introduction and Elastic Analysis
Lecture 14.3: Analysis of Portal Frames: Plastic Analysis
Lecture 14.8: Classification of Multi-Storey Frames
Lecture 14.9: Methods of Analysis for Multi-Storey Frames
Lecture 14.10: Simple Braced Non-Sway Multi-Storey Buildings
Lecture 14.13: Design of Multi-Storey Frames with Partial Strength and Semi-Rigid Connections
Lecture 14.14: Methods of Analysis of Rigid Jointed Frames
SUMMARY
Techniques for the determination of the individual member forces in steel frames are described and discussed. These techniques include first and second
order approaches based on both elastic and plastic theory. The different approaches to the design and construction of steel frames permitted by
Eurocode 3 [1] are explained and their implementation outlined.
1. INTRODUCTION
Frames of varying size and complexity represent one of the most frequent uses of structural steel. Whilst the most obvious application is in buildings,
support frames for bridges, offshore platforms, falsework and industrial storage systems also constitute a significant usage.
The main components of a rectangular arrangement are identified in Figure 1. Vertical loads on the roof and floors are transmitted by bending and shear
into the columns, which, in turn, transfer load into the foundations by means of compressive, bending and shearing actions. Horizontal loading, e.g. due
to wind, must also be transferred into the foundations and may, depending upon the frame geometry and the relative magnitudes of the vertical and
lateral loads, induce tension in some columns and therefore uplift on the foundations.
ESDEP WG 7 file:///D:/str/SCOALA/2009-2010/PBP/lit/structural_analysis/l1100.htm
1 of 13 12.04.2010 19:19
In general, a 3-dimensional building frame may be separated into a set of planar frames with well-defined support or restraint conditions for out-of-plane
deformations, see Figure 1. These planer frames should be investigated for two different limit state conditions:
Ultimate limit state.
Serviceability limit state.
Details of these investigations are provided in later lectures. In this introductory lecture attention is focused on describing the main aspects of frame
behaviour and the ways in which these aspects are linked to various techniques for predicting structural response. The lecture is a preparation for later
more detailed treatments.
2. FRAMING SYSTEMS
For the purposes of analysis and design, steel frames have traditionally been regarded as belonging to one of two categories:
pin-jointed (simple construction).
rigid-jointed (continuous construction).
Of course, examples exist for which elements of both types are present; the present discussion does not consider these cases in developing the subject.
In Eurocode 3 this simple subdivision has been extended by including consideration of the method of analysis and including joints that behave as
semi-rigid. This leads to the more complex classification system that is shown in Table 1.
Type of framingMethod of global
analysis
Types of connections
Simple Pin joints× Nominally pinned
× Nominally pinned
Continuous Elastic× Rigid
ESDEP WG 7 file:///D:/str/SCOALA/2009-2010/PBP/lit/structural_analysis/l1100.htm
2 of 13 12.04.2010 19:19
× Nominally pinned
Rigid-Plastic× Full-strength
× Nominally pinned
Elastic-Plastic× Full-strength - Rigid
× Nominally pinned
Semi-continuous Elastic× Semi-rigid
× Rigid
× Nominally pinned
Rigid-Plastic× Partial-strength
× Full-strength
× Nominally pinned
Elastic-Plastic× Partial-strength - Semi-rigid
× Partial-strength - Rigid
× Full-strength - Semi-rigid
× Full-strength - Rigid
× Nominally pinned
Table 1 Methods of framing and global analysis in Eurocode 3
This introductory lecture does not cover the cases where the joints are semi-rigid. Further information on this type of joint and their influence on frame
design is given in Lectures 11.7 and 14.13.
3. SIMPLE CONSTRUCTION
Building frames designed and executed according to this principle require comparatively little analysis as the loads may be allocated to individual
members on the basis of simple statics. Since the joints are assumed to be incapable of transmitting moments, lateral stability requires the use of bracing
because a rectangular bay with pinned beam to column connections, of course, possess no lateral stiffness. The only exception to this condition is when
the feet of the columns are rigidly fixed to a solid foundation so that they can function as vertical cantilevers. Figure 2 illustrates these points.
ESDEP WG 7 file:///D:/str/SCOALA/2009-2010/PBP/lit/structural_analysis/l1100.htm
3 of 13 12.04.2010 19:19
Once the forces in the members have been decided upon, design may be conducted by considering individual beams, columns and joints, using the
procedures presented in Lectures 7 and 11 respectively. All horizontal loading is assumed to be resisted by the bracing system and, in the terminology of
Eurocode 3 [1], the structure is designed as a braced frame.
4. CONTINUOUS CONSTRUCTION
When rigid joints are used, considerable interaction between beams and columns occurs due to transfer of moments around the frame. Various
approaches to analysis and design may be employed; the most important consideration is the extent to which the effects of deflections on the response of
the frame must be taken into account. Although rigid joints may be used in conjunction with bracing, construction economies make this arrangement an
uncommon solution. Rigid joints are normally only used as an alternative to bracing so that lateral stiffness is provided by so-called frame action as
illustrated in Figure 3.
5. METHODS OF ANALYSIS
5.1 First-Order Elastic Analysis
ESDEP WG 7 file:///D:/str/SCOALA/2009-2010/PBP/lit/structural_analysis/l1100.htm
4 of 13 12.04.2010 19:19
In first-order elastic analysis a linear relationship between the applied loading F and the deformations (d) is assumed. The internal force distribution in
the frame is assumed to be unaffected by the displacements in the frame.
Frame analysis can therefore be conducted according to linear elastic principles as outlined in Lecture 7.1. The frame responds according to line 1 in
Figure 4.
5.2 First-Order Rigid-Plastic Analysis
Rigid-plastic analysis (or the application of simple plastic theory) neglects the effects of elastic deflections and assumes that all structural deformation
takes place in discrete regions, called plastic hinges, where plasticity has developed. When using first-order, rigid-plastic theory only the collapse
condition is addressed. This condition occurs when sufficient plastic hinges are assumed to have formed to convert the structure into a mechanism. Thus
the path by which this stage is reached, i.e. the sequence of formation of the hinges and any intermediate distributions of internal forces, are not
considered. Figure 5 illustrates the concept for 3 cases of vertical, horizontal and combined loading, whilst curve 2 in Figure 4 gives the frame response
according to this approach. Due to the form of the analysis, no information is provided on the magnitude of the deflections. The analysis gives only that
all stiffness is lost at the collapse load and deflections therefore (in theory) become uncontrolled.
ESDEP WG 7 file:///D:/str/SCOALA/2009-2010/PBP/lit/structural_analysis/l1100.htm
5 of 13 12.04.2010 19:19
5.3 Elastic Critical Load
Using the methods described in Lectures 6, it is possible to calculate the buckling loads for frames under suitably idealised loading. Depending upon the
content and complexity of the frame, several different buckling modes, each with its associated elastic vertical load, may be possible. For the simple
portal frame shown in Figure 6, both a symmetrical and an antisymmetrical mode are possible; the latter will usually be avoided with a much lower
critical load. Once again the analysis provides no information on the magnitude of the deflections; it simply identifies a particular load level. The curve 3
in Figure 4 gives the representation of the critical load obtained by an elastic buckling analysis.
ESDEP WG 7 file:///D:/str/SCOALA/2009-2010/PBP/lit/structural_analysis/l1100.htm
6 of 13 12.04.2010 19:19
5.4 Second-Order Elastic Analysis
In second-order elastic analysis the effect of elastic deformations on the internal force distribution is taken into account. The result is a transition from
the linear analysis line 1 at low loads to the elastic critical line 3 at large deflections. For frames the second-order effects may be separated into 2 parts:
reduction in the effective bending stiffnesses of individual members due to compressive loading.
a destabilising effect due to the overturning moment produced by the vertical loads acting through the horizontal deflections caused by the lateral
loads.
5.5 Second-Order Rigid-Plastic Analysis
If the deformations that may develop as a result of the formation of the plastic collapse mechanism are allowed for when formulating the equilibrium of
the frame, then the result is the developing mechanism curve of line 5 in Figure 4. This curve shows that equilibrium can only be maintained with a
reduction in the level of the applied loads.
5.6 First-Order, Elastic-Plastic Theory
If a linear elastic analysis is modified to allow for reductions in frame stiffness with the progressive formation of plastic hinges at increasing levels of the
applied load, then the response curve of line 6 is obtained. This line exhibits progressive loss of stiffness as each plastic hinge is formed and eventually
merges with the rigid-plastic line 2.
5.7 Second-Order, Elastic-Plastic Analysis
When the analysis that traces the formation of plastic hinges also allows for the effects of deformations in setting up the governing equations, then line 6
is modified somewhat into line 7. Line 7 initially follows the first-order elastic line 1 but diverges from this line to follow the second-order elastic line 4
as destabilising effects become more significant. Formation of the first plastic hinge - which occurs at a slightly lower applied load than is the case with
the first-order, elasto-plastic analysis due to the larger deformation associated with second-order analysis - further reduces the stiffness, causing line 7 to
diverge from line 4. This divergence becomes more pronounced as more plastic hinges form. The peak of this curve corresponds to the failure load
predicted by this type of analysis. At large deformations line 7 tends to merge with the curve for the mechanism, line 5.
5.8 Second-Order, Plastic Zone Analysis
ESDEP WG 7 file:///D:/str/SCOALA/2009-2010/PBP/lit/structural_analysis/l1100.htm
7 of 13 12.04.2010 19:19
If the spread of plasticity both through the cross-section and along the member length is taken into account, instead of assuming that it is concentrated
into the desirable regions of the plastic hinges, then the resulting type of analysis is usually termed plastic zone theory. It provides an even closer
representation of actual behaviour and leads to a curve similar to line 7.
6. COMMENTS
In principle, any of the above approaches to frame analysis may be adopted. In practice, some of the effects may be found to be of little real significance
for certain classes of structure, e.g. for many low-rise frames second-order effects are very small and may reasonably be neglected. Certain cases may
also arise where particular forms of response should be avoided, e.g. for buildings containing heavy cranes which will cause repeated loading, elastic
design is normally employed.
The more complex approaches will almost certainly require the use of suitable computer software to implement the volume of calculation. It is therefore
important to select an approach which is compatible with both the accuracy required and the level of importance of the project under consideration.
When calculating deflections at working load levels for the purpose of checking serviceability, it is usual to employ only linear elastic analysis.
7. FRAME CLASSIFICATION
In order to provide guidance on the most appropriate type of analysis to use in particular cases, Eurocode 3 has introduced the idea of frame
classification [1]. A double condition is used:
braced or unbraced.
non-sway or sway.
7.1 Braced Frames
A frame may be classified as braced if its sway resistance is supplied by a bracing system with a response to in-plane horizontal loads which is
sufficiently stiff for it to be acceptably accurate to assume that all horizontal loads are resisted by the bracing system.
This may be further quantified as:
A steel frame may be classified as braced if the bracing system reduces its horizontal displacements by at least 80%.
For such frames first-order elastic or plastic theory should be used.
When the above conditions are not satisfied the frame must be considered as unbraced.
When designing the bracing system:
The effects of the initial sway imperfections, given in Clause 5.2.4.3 of Eurocode 3 [1] and discussed later in these notes, in the braced frame shall
be taken into account in the design of the bracing system.
The initial sway imperfections plus any horizontal loads applied to a braced frame, may be treated as affecting only the bracing system.
The bracing system should be designed to resist:
- any horizontal loads applied to the frames which it braces.
- any horizontal or vertical loads applied directly to the bracing system.
- the effects of the initial sway imperfections (or the equivalent horizontal forces) from the bracing system itself and from all the frames which it braces.
Where the bracing system is a frame or sub-frame, it may itself be either sway or non-sway.
7.2 Unbraced Frames
An unbraced frame may be classified as a non-sway frame according to Clause 5.2.5.2 of Eurocode 3 [1] providing:
Its response to in-plane horizontal forces is sufficiently stiff for it to be acceptably accurate to neglect any additional internal forces or moments
arising from horizontal displacements of its nodes.
This classification may be further quantified as:
A frame may be classified as non-sway for a given load case if the elastic critical load ratio VSd /Vcr for that load case satisfies the criterion:
VSd /Vcr £ 0,1
where VSd is the design value of the total vertical load.
Vcr is its elastic critical value for failure in a sway mode.
Beam-and-column type plane frames in building structures with beams connecting each column at each storey level may be classified as non-sway
for a given load case if the following criterion is satisfied. When first-order theory is used, the horizontal displacements in each storey due to the
design loads (both horizontal and vertical), plus the initial sway imperfection applied in the form of equivalent horizontal forces, should satisfy the
criterion:
where d is the horizontal displacement at the top of the storey, relative to the bottom of the storey.
ESDEP WG 7 file:///D:/str/SCOALA/2009-2010/PBP/lit/structural_analysis/l1100.htm
8 of 13 12.04.2010 19:19
h is the storey height.
H is the total horizontal reaction at the bottom of the storey.
V is the total vertical reaction at the bottom of the storey.
Both requirements follow from the idea that, if satisfied, the load-carrying resistance determined by neglecting sway effects will be only a ten per cent
less than that calculated by including such effects. This approach is, in turn, based upon the Merchant-Rankine concept for estimating the true ultimate
load of a frame that fails by some from of inelastic instability from a knowledge of its elastic critical load and its first-order, rigid-plastic collapse load.
Both loads are relatively straightforward to calculate.
The original Merchant-Rankine formulae for the failure load Vsd is:
where:
Vcr is the elastic critical load.
Vpl is the first-order, rigid-plastic collapse load.
From this it is clear that when Vcr >> Vpl, then Vsd ~ Vpl.
Non-sway frames should be designed using first-order elastic or plastic theory to resist safely the arrangements of loads that lead to the most severe
combinations of internal forces and moments in the individual members and connections. The effects of restraint to columns in improving their stability
should be taken into account by using the concept of effective buckling length as explained in Lecture 7.7.
Frames that do not meet the above requirements must be designed as sway frames.
7.3 Sway Frames
Sway frames shall be analysed under those arrangements of the variable loads which are critical for failure in a sway mode. In addition, sway frames
shall also be analysed for the non-sway mode.
The initial sway imperfections, and member imperfections where necessary, shall be included in the global analysis of all frames.
The allowance for imperfections in the analysis of sway frames is intended to cover effects such as lack of verticality, lack of straightness, residual
stresses, etc. It is expressed in Eurocode 3 by means of a set of equivalent geometrical imperfections [1]. These imperfections are not actual construction
tolerances but, because they are intended to represent the effect of a number of factors, are likely to be larger than such tolerances. The form specified in
Eurocode 3 is:
The effects of imperfections shall be allowed for in frame analysis by means of an equivalent geometric imperfection in the form of an initial sway
imperfection f determined from:
f = kc ks fo
with fo = 1/200
kc = [0,5 + 1/nc]0,5
but kc £ 1,0
and ks = [0,2 + 1/ns]0,5
but ks £ 1,0
where nc is the number of columns per plane.
ns is the number of storeys.
Columns which carry a vertical load NSd of less than 50% of the mean value of the vertical load per column in the plane considered, shall not be
included in nc.
Columns which do not extend through all the storeys included in ns shall not be included in nc. Those floor levels and roof levels which are not
connected to all the columns included in nc shall not be included when determining ns.
These initial sway imperfections apply in all horizontal directions, but need only be considered in one direction at a time.
The possible torsional effects on the structure of anti-symmetric sways, on two opposite faces, shall also be considered.
If more convenient, the initial sway imperfection may be replaced by a closed system of equivalent horizontal forces, see Figure 7.
In beam-and-column building frames, these equivalent horizontal forces should be applied at each floor and roof level and should be proportionate
to the vertical loads applied to the structure at that level, see Figure 8.
The horizontal reactions at each support should be determined using the initial sway imperfection and not the equivalent horizontal forces. In the
absence of actual horizontal loads, the net horizontal reaction is zero.
ESDEP WG 7 file:///D:/str/SCOALA/2009-2010/PBP/lit/structural_analysis/l1100.htm
9 of 13 12.04.2010 19:19
First-order or second-order analysis may be used. If the analysis is first-order, second-order effects may be allowed for in an appropriate way when
designing the columns by using the results of a first-order analysis and either:
- using amplified sway moments, or
- using the sway-mode buckling lengths.
When second-order elastic global analysis is used, in-plane buckling lengths for the non-sway mode may be used for member design.
In the amplified sway moments method, the sway moments found by a first-order elastic analysis should be increased by multiplying them by the
ratio:
where VSd is the design value of the total vertical load.
Vcr is its elastic critical value for failure in a sway mode.
The amplified sway moments method should not be used when the elastic critical load ratio VSd/Vcr is more than 0,25.
Sway moments are those associated with the horizontal translation of the top of a storey relative to the bottom of that storey. They arise from
horizontal loading and may also arise from vertical loading if either the structure or the loading is asymmetrical.
As an alternative to determining VSd/Vcr directly, the following approximation may be used in beam-and-column type frames:
where d, h, H and V are as defined previously.
When the amplified sway moments method is used, in-plane buckling lengths for the non-sway mode may be used for member design.
When first-order elastic analysis with sway-mode in-plane buckling lengths is used for column design, the sway moments in the beams and the
beam-to-column connections should be amplified by at least 1,2 unless a smaller value is shown by analysis to be adequate.
Rules for the application of plastic analysis procedures to sway frames are given in Clause 5.2.6.3 of Eurocode 3 [1].
8. MEMBER CHECK AND FRAME DESIGN
ESDEP WG 7 file:///D:/str/SCOALA/2009-2010/PBP/lit/structural_analysis/l1100.htm
10 of 13 12.04.2010 19:19
Satisfying the verification rules for resistance and stability of frames has to assure that neither the frame as a whole, nor the isolated members in the
frame on their own, will collapse under a load which is smaller than the design load. For the safety verification of the individual members, the members
may be separated from the frames to be dealt with as independent isolated sub-structures. The end conditions of the members should then comply with
the deformation conditions of the members in the special frame in a conservative way (e.g. by assuming nominally pinned end conditions) and the
interaction effects at the ends of the members should be considered by applying equivalent end moments and end forces, see Figure 9.
In the safety verification of these separated members, the member imperfections must be taken into account; these imperfections have normally
been included when formulating the member design rules as explained in other Lectures 7.
In general, the isolated members by their loading and end-conditions represent simply supported beam-columns with or without restraints between
their ends, see Figure 10. Beam-columns are members loaded by normal forces and moments about one or two axes.
ESDEP WG 7 file:///D:/str/SCOALA/2009-2010/PBP/lit/structural_analysis/l1100.htm
11 of 13 12.04.2010 19:19
If, in a second-order elasto-plastic calculation, the real behaviour of the frame has been approximated and local instability and out-of-plane buckling is
prevented, then further verification is not needed. In this case the strength check - also called the cross-sectional check - is implicity satisfied by working
with the actual distribution of forces and moments. This is also valid for the stability check. It has to be shown that the equilibrium is stable under the
design load. In other words: VSd representing the design load, must be less than the elasto-plastic collapse load Vk.
If the distribution of forces and moments, as a result of the design load, is calculated with a first-order elastic method, then it is quite possible that the
actual elasto-plastic resistance Vk of the frame is exceeded. Verification rules to overcome this problem are therefore needed. On the one hand, cross-
sectional checks are needed, to show that each cross-section can offer enough resistance to withstand normal forces, shear forces and bending moments
due to the design load. On the other hand, stability checks are necessary to show that every member and the frame as a whole are stable.
In general, for each method of calculating the distribution of forces and moments, additional verification rules are necessary related to the specific
method of calculating the distribution of forces and moments. All collapse mechanisms which are relevant for the frame and which have not been taken
into account in calculating the distribution of forces and moments, should be checked by using adequate verification rules.
If a frame can deform only in its own plane and plate buckling (of web and/or flange), torsion, torsional buckling and lateral-torsional buckling are not
relevant, then there are only two types of verification rules of importance: cross-sectional checks and stability checks. Depending on the method of
calculating the distribution of forces and moments, specific verification rules must be taken into account. Table 2 shows that these rules depend on the
calculation method used.
Table 2 Relation between global analysis and code check
Method for calculation the forces and moment distribution Cross-sectional verification rules Stability checks
First-order elastic
First-order plastic
YES
NO
YES
YES
ESDEP WG 7 file:///D:/str/SCOALA/2009-2010/PBP/lit/structural_analysis/l1100.htm
12 of 13 12.04.2010 19:19
Second-order elastic
Second-order plastic
YES
NO
NO
NO
When the method of calculating the distribution of the forces and moments is relatively simple, the verification rules are complex and the other way
around. In general verification rules for members are used in the step after the calculation of the distribution of forces and moments in a frame.
9. CONCLUDING SUMMARY
Frame behaviour and thus the approach which should be used in design has been shown to be crucially dependent upon the type of joints used.
The 2 main forms of construction are:
i. simple construction - assumed joints act as if pinned.
ii. continuous construction - assumed joints act as if rigid.
Simple statics is usually all that is needed to determine the distribution of internal forces in the individual members of frames designed according to
the principles of simple construction.
8 different approaches - varying in precision and complexity - to the analysis of rigid jointed frames are possible.
Eurocode 3 classifies frames as braced/unbraced and for the latter as either non-sway/sway. The basis for this classification is an assessment of the
extent to which deformations influence the response of the frame.
Different design approaches are necessary for the three classes:
i. braced.
ii. unbraced and non-sway.
iii. unbraced and sway.
Each approach has been outlined, including the treatment of imperfections and the link between the approach adopted to consider overall frame
behaviour and that necessary when considering individual members.
10. REFERENCES
[1] Eurocode 3: "Design of Steel Structures": ENV 1993-1-1: Part 1.1, General rules and rules for buildings, CEN, 1992.
11. ADDITIONAL READING
Galambos, T.V. "Guide to Stability Design Criteria for Metal Structures", 4th Edition, John Wiley & Son, 1988.1.
Horne, M. R, and Merchant, W., "The Stability of Frames", Pergamen Press, 1965.2.
Chen, W.F. and Lui, E.M. "Stability Design of Steel Frames", CRC Press, 1991.3.
Ballio, G. and Mazzolani, F. M., "Theory and Design of Steel Structures", Chapman and Hall, 1983.4.
Chapter on stability.
Trahair, N. S. and Bradford, M. A., "Behaviour and Design of Steel Structures", Chapman and Hall, 1983.5.
Chapter on frames.
Previous | Next | Contents
ESDEP WG 7 file:///D:/str/SCOALA/2009-2010/PBP/lit/structural_analysis/l1100.htm
13 of 13 12.04.2010 19:19