c h a p t e r t w e lv e threads, fasteners, and springs

C H A P T E R T W E LV E

THREADS, FASTENERS,THREADS, FASTENERS,AND SPRINGSAND SPRINGS

2Technical Drawing with Engineering Graphics, 14/eGiesecke, Hill, Spencer, Dygdon, Novak, Lockhart, Goodman

© 2012, 2009, 2003, Pearson Higher Education,Upper Saddle River, NJ 07458. • All Rights Reserved.

OBJECTIVESOBJECTIVES

1. Define and label the parts of a screw thread.

2. Identify various screw thread forms.

3. Draw detailed, schematic, and simplified threads.

4. Define typical thread specifications.

5. Identify various fasteners and describe their use.

6. Draw various screw head types.

7. Draw springs.



UNDERSTANDING THREADS AND UNDERSTANDING THREADS AND FASTENERSFASTENERS

The three basic applications of Screw threads are as follows:

1. To hold parts together…

2. To provide for adjustment between parts…

3. To transmit power…

Thread Used for Attachment.(Courtesy of Arthur S. Aubry/GettyImages, Inc.-Photodisc.)



Screw Thread TermsScrew Thread Terms

Screw Thread Nomenclature

Study 55 of your textbook for all thread and fastener terms



Screw Thread FormsScrew Thread Forms



Thread PitchThread Pitch

The pitch of any thread form is the distance parallel to the axis between correspondingpoints on adjacent threads.The pitch or the number of threads per inch can be measured with a scale orwith a thread pitch gage.



Thread SeriesThread SeriesThe thread series is the detail of the shape and number of threads per inch composing different groups of fasteners.

Five series of threads were used in the old ANSI standards:

Coarse thread

Fine thread

8-pitch thread

12-pitch thread

16-pitch thread



Right-Hand and Left-Hand ThreadsRight-Hand and Left-Hand ThreadsAright-hand thread is one that advances into a nut when turned clockwise, and a left-hand thread is one that advances into a nut when turned counterclockwise.



Single and Multiple ThreadsSingle and Multiple ThreadsA single thread, as the name implies, is composed of one ridge, and the lead is therefore equal to the pitch.

Multiple threads are used wherever quick motion, but not great power, is desired, as on ballpoint pens, toothpaste caps, valve stems, and so on.



American National Thread FitsAmerican National Thread Fits and and

Metric and Unified Thread FitsMetric and Unified Thread FitsFor general use, three classes of fits between mating threads (as between bolt and nut) have been established by ANSI. These fits are produced by the application of tolerances listed in the standard and are as follows:

• Class 1 fit

• Class 2 fit

• Class 3 fitThere are two general classes of metric thread fits:

• 6H for internal threads

• 6g for external threads



Three Methods for Drawing ThreadThree Methods for Drawing Thread

1. Detailed

2. Schematic

3. Simplified



THREAD NOTESTHREAD NOTESASME/ANSI Y14.6, Screw Thread Representation, is a standard for representing, specifying, and dimensioning screw threads on drawings



EXTERNAL THREAD SYMBOLSEXTERNAL THREAD SYMBOLS

Schematic threads are indicated by alternating long and short lines.

With Simplified representations, threaded portions are indicated byhidden lines parallel to the axis at the approximate depth of the thread, whether the cylinder appears rectangular or circular.



INTERNAL THREAD SYMBOLSINTERNAL THREAD SYMBOLSThe only differences between the schematic and simplified internal thread symbols occur in the sectional views.

In the case of blind tapped holes, the drill depth normally is drawn at least three schematic pitches beyond the thread length



DETAILED REPRESENTATION:DETAILED REPRESENTATION:METRIC, UNIFIED, AND AMERICAN NATIONAL THREADS

The detailed representation for metric, unified, and American national threads is the same, since the flats are disregarded.

Notice that for left-hand threads the linesslope upward to the left

Notice that for right-hand threads the linesslope upward to the right



DETAILED REPRESENTATIONDETAILED REPRESENTATION (External and Internal Square Thread): (External and Internal Square Thread):

Sometimes in assemblies the root and crest lines may be omitted from the nut only portion of the drawing so that it is easier to identify the inserted screw.



Threads in PHANTOM and AssembliesThreads in PHANTOM and AssembliesUse phantom lines to save time when representing identical Features Threaded shafts and springs may be shortened without using conventional breaks but must be correctly dimensioned.

When external and internal threads are sectioned in assembly, the V’s are required to show the threaded connection.



AMERICAN NATIONAL STANDARD AMERICAN NATIONAL STANDARD PIPE THREADSPIPE THREADS

American National Standard Taper Pipe Thread. (Reprinted from ASME B1.20.1-1983 (R1992), by permission of The American Society of Mechanical Engineers. All rights reserved.)

The tapered profile of the pipe thread…



BOLTS, STUDS, AND SCREWSBOLTS, STUDS, AND SCREWSThe term bolt is generally used to denote a “through bolt” that has a head on one end, is passed through clearance holes in two or more aligned parts, and is threaded on the other end to receive a nut to tighten and hold the parts together.



Screw HeadsScrew Heads

Do not section bolts, nuts, screws, and similar parts when drawn in assembly because they do not have interior detail that needs to be shown.

Do not section bolts, nuts, screws, and similar parts when drawn in assembly because they do not have interior detail that needs to be shown.

A machine screw is similar to a slotted head cap screw but usually smaller. A set screw is a screw, with or without a head, that is screwed through one member and whose special point is forced against another member to prevent motion between the two parts.



TAPPED HOLESTAPPED HOLESWhen an ordinary drill is used to make holes that will be tapped, it is referred to as a tap drill. When drawing the drill point, use an angle of 30° to approximate the actual 31° slope of the drill bit. The thread length is the length of full or perfect threads. The tap drill depth does not include the cone point of the drill.



DRAWING STANDARD BOLTSDRAWING STANDARD BOLTSBolt Proportions (Regular)



Locknuts and Locking DevicesLocknuts and Locking DevicesMany types of special nuts and devices to prevent nuts from unscrewing are available, and some of the most common areShown below.



STANDARD CAP SCREWSSTANDARD CAP SCREWSCap screws are normally finished and are used on machine tools and other machines when accuracy and appearance are important.



STANDARD MACHINE SCREWSSTANDARD MACHINE SCREWS

Machine screws are similar to cap screws but are usually smaller (.060" to .750" diameter) and the threads generally go all the way to the head.

Clearance holes and counterbores shouldbe made slightly larger than the screws.Typical machine screw notes are…



Set Screws. (Courtesy of Penninsula Components Inc.)

STANDARD SET SCREWSSTANDARD SET SCREWSA set screw is screwed into one part so that its point bears firmly against another part. Ifthe point of the set screw is cupped, or if a flat is milled on the shaft, the screw will hold much more firmly.

Set screws are specified as follows…



AMERICAN NATIONAL STANDARD AMERICAN NATIONAL STANDARD WOOD SCREWSWOOD SCREWS

(Courtesy of Michael Newman/

PhotoEdit Inc.)

Wood screws with three types of heads—flat, round, and oval—have been standardized.



Miscellaneous Bolts and ScrewsMiscellaneous Bolts and Screws



KEYSKEYSKeys are used to prevent movement between shafts and wheels, couplings, cranks, and similar machine parts attached to or supported by shafts.

Typical specifications for keys are…



MACHINE PINS and RIVETSMACHINE PINS and RIVETS

Taper Pin

Machine pins include taper pins, straight pins, dowel pins, clevis pins, and cotter pins. For light work, taper pins can be used to fasten hubs or collars to shafts.

Note that the rectangular view of each rivet shows the shank of the rivet with both heads made with circular arcs, and the circular view of each rivet is represented by only the outside circle of the head.



Rivet SymbolsRivet SymbolsBecause many engineering structures are too large to be built in the shop, they are built in the largest units possible and then are transported to the desired location. Trusses are common examples. Therivets driven in the shop are called shop rivets, and those driven on the job are called field rivets.



SPRINGSSPRINGSA spring is a mechanical device designed to store energy when deflected and to return the equivalent amount o f energy when released, ANSI Y14.13M. Springs are commonly made of spring steel, which may be musicwire, hard-drawn wire, or oil-tempered wire. Other materials used for compression springs include stainless steel, beryllium copper, and phosphor bronze. Urethane plastic is used in applications where conventional springs would be affected by corrosion, vibration, or acoustic or magneticforces.

Springs. Norton, Robert L., Machine Design: An Integrated Approach, 3rd, © 2006. Printed and electronically reproduced by permission of Pearson Education, Inc., Upper Saddle River, New Jersey.)

Steps in Detailed Representation of Spring

c h a p t e r t w e lv e threads, fasteners, and springs

Documents

pitch thread

thread series

single thread

coarse thread fine thread

power thread

e giesecke

screw thread forms slide

thread pitch gage