bxa 800 series
DESCRIPTION
BXA 800 SeriesTRANSCRIPT
Slant +/- 45° Dual-Polarized Panel Antennas806-900 MHz, 806-960 MHz
Model Number Frequency Range(MHz) H-Plane E-Plane Gain
(dBd)Fixed Electrical
Downtilt Options**Length x Width x Depth
(in inches)BXA-80040/4CF _ 806-900 MHz* 40° 15° 14.5 dBd 0°, 5° 47.2” x 23.6” x 7.9”BXA-80040/6CF _ 806-900 MHz* 40° 10° 16 dBd 0°, 6° 71.1” x 23.6” x 7.9”
BXA-80040/8BF _ 806-900 MHz* 40° 7° 18 dBd 0° 94.7” x 23.6” x 7.9”BXA-80040/8CF _ 806-900 MHz* 40° 7° 18 dBd 0°, 3°, 6° 94.7” x 23.6” x 7.9”BXA-80063/2CF _ 806-900 MHz* 63° 30° 10 dBd 0°, 3°, 5°, 7°, 9° 23.8” x 11.2” x 5.0”BXA-80063/4CF _ 806-900 MHz* 63° 15° 13 dBd 0°, 4°, 5°, 6° 47.4” x 11.2” x 5.0”BXA-80063/6BF _ 806-900 MHz* 63° 11° 14.5 dBd 15° 71.1” x 11.2” x 5.0”BXA-80063/6CF _ 806-900 MHz* 63° 11° 14.5 dBd 0°, 2°, 3°, 5°, 6° 71.1” x 11.2” x 5.0”BXA-80063/8CF _ 806-900 MHz* 63° 7° 16 dBd 0°, 2°, 3°, 5° 94.7” x 11.2” x 5.0”BXA-80080/4CF _ 806-900 MHz* 80° 15° 12 dBd 0° 48.2” x 11.2” x 5.9”BXA-80080/6CF _ 806-900 MHz* 80° 11° 13.5 dBd 0° 72.6” x 11.2” x 4.6”BXA-80080/8CF _ 806-900 MHz* 80° 7° 15 dBd 0° 96.5” x 11.2” x 5.9”BXA-80090/2CF _ 806-900 MHz* 90° 30° 8 dBd 0° 23.8” x 8.1” x 5.7”BXA-80090/4CF _ 806-960 MHz 90° 15° 11 dBd 0°, 2°, 4° 47.4” x 8.1” x 5.7”BXA-80090/6CF _ 806-900 MHz* 90° 11° 12.5 dBd 0°, 3°, 4° 71.1” x 8.1” x 5.7”BXA-80090/8BF _ 806-900 MHz* 90° 7° 14 dBd 0° 94.7” x 8.1” x 5.7”BXA-80090/8CF _ 806-900 MHz* 90° 7° 14 dBd 0°, 3°, 4°, 5° 94.7” x 8.1” x 5.7”
BXA- 800 90 / 4 CF E-DIN 4°
Electrical DowntiltConnector TypeNE is an elongated N connector.E-DIN is an elongated DIN connector
CF refers to a “Center-Fed” connector.BF refers to a “Bottom-Fed” connector.
Number of Dipole PairsAlso refers to approx. length in feet
Horizontal Beamwidth
Operating Frequency Range800 = Operates within 806-900 MHz
or 806-960 MHz
BXA-800 Series
The BXA (Broadband X-Pol Antenna) is a slant +/- 45° dual-polarized panel covering the 806-900 MHz and 806-960 MHz frequen-cy range. Our unique all mechanical design and patented, slotted dipole element ensure excellent overall performance with similarelectrical performance from both ports and consistent and repeatable performance from all production units of the same model.These characteristics contribute significantly to the overall quality of a carrier’s network. Antennas are available with fixed electricaldowntilt.
Design and Construction of the BXA-800 Panel:BXA antennas are manufactured with our exclusive 3T Technology, featuring single-piece, water-cut brass feedline assemblies forconsistent performance; a non-collinear system with access to each radiating element for control of the shaping of the vertical pat-tern; air as insulation for virtually no internal signal loss; fiberglass radomes and aircraft grade aluminum reflector plates for evenheat dissipation to minimize plate warping and bending.Model Number Guide:
Amphenol Antel, Inc.
Model’s Currently Available:
*This model is also available for 870-960 MHz. Contact your sales representative for details.**Some downtilt models may operate at a different frequency range than that listed. Please consult specification sheet for actual frequency range.When ordering replace “__” with the connector type (NE or E-DIN).
Slant +/- 45° Dual Polarized, Panel 40° / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80040/4CF __
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1200 mm 47.2 in
Width 600 mm 23.6 in
Depth Depth with z-bracket
200240
mmmm
7.99.4
inin
4) Weight 11.3 kg 25.0 lbs
Wind AreaFore/Aft 0.72 m2 7.8 ft2
Side 0.24 m2 2.6 ft2
Rated Wind Velocity (Safety factor 2.0)>272 km/hr >162 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 1019 N 229.0 lbsSide 351 N 78.9 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports ≤ -27 dB1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 40°
E-Plane 15°1) Electrical Downtilt 0°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 40° / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80040/4CF __ 5°
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1200 mm 47.2 in
Width 600 mm 23.6 in
Depth Depth with z-bracket
200240
mmmm
7.99.4
inin
4) Weight 11.3 kg 25.0 lbs
Wind AreaFore/Aft 0.72 m2 7.8 ft2
Side 0.24 m2 2.6 ft2
Rated Wind Velocity (Safety factor 2.0)>272 km/hr >162 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 1019 N 229.0 lbsSide 351 N 78.9 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports ≤ -27 dB1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 40°
E-Plane 15°1) Electrical Downtilt 5°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 40° / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80040/6CF __
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1805 mm 71.1 in
Width 600 mm 23.6 inDepthDepth with z-bracket
200240
mmmm
7.99.4
inin
4) Weight 17 kg 37.5 lbs
Wind AreaFore/Aft 1.08 m2 11.7 ft2
Side 0.36 m2 3.9 ft2
Rated Wind Velocity (Safety factor 2.0)>180 km/hr >112 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 1543 N 347.0 lbsSide 545 N 122.5 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports ≤ -27 dB1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 40°
E-Plane 10°1) Electrical Downtilt 0°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 40° / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80040/6CF __ 6°
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1805 mm 71.1 in
Width 600 mm 23.6 inDepthDepth with z-bracket
200240
mmmm
7.99.4
inin
4) Weight 17 kg 37.5 lbs
Wind AreaFore/Aft 1.08 m2 11.7 ft2
Side 0.36 m2 3.9 ft2
Rated Wind Velocity (Safety factor 2.0)>180 km/hr >112 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 1543 N 347.0 lbsSide 545 N 122.5 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports ≤ -27 dB1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 40°
E-Plane 10°1) Electrical Downtilt 6°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 40° / 18 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80040/8CF __
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / centeror bottom
1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports ≤ -27 dB1) Gain 18 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 40°
E-Plane 7°1) Electrical Downtilt 0°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna can be ordered with center-fed or bottom-fed connectors.
Center-fed: BXA-80040/8CF + (NE or E-DIN)Bottom-fed: BXA-80040/8BF + (NE or E-DIN)
Length 2405 mm 94.7 in
Width 600 mm 23.6 in
DepthDepth with z-bracket
200240
mmmm
7.99.4
inin
4) Weight 22.7 kg 50.0 lbs
Wind AreaFore/Aft 1.44 m2 15.5 ft2
Side 0.48 m2 5.2 ft2
Rated Wind Velocity (Safety factor 2.0)>206 km/hr >128 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 2059 N 463.0 lbsSide 782 N 175.7 lbs
Slant +/- 45° Dual Polarized, Panel 40° / 18 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80040/8BF __
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 2405 mm 94.7 in
Width 600 mm 23.6 in
DepthDepth with z-bracket
200240
mmmm
7.99.4
inin
4) Weight 22.7 kg 50.0 lbs
Wind AreaFore/Aft 1.44 m2 15.5 ft2
Side 0.48 m2 5.2 ft2
Rated Wind Velocity (Safety factor 2.0)>206 km/hr >128 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 2059 N 463.0 lbsSide 782 N 175.7 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / bottomor center
1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports ≤ -27 dB1) Gain 18 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 40°
E-Plane 7°1) Electrical Downtilt 0°1) Null Fill 5%
Lightning Protection Direct Ground
BF Denotes a Bottom-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna can be ordered with bottom-fed orcenter-fed connectors.
Bottom-fed: BXA-80040/8BF + (NE or E-DIN)Center-fed: BXA-80040/8CF + (NE or E-DIN)
Slant +/- 45° Dual Polarized, Panel 40° / 18 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80040/8CF __ 3°
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center 1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports ≤ -27 dB1) Gain 18 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 40°
E-Plane 7°1) Electrical Downtilt 3°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Length 2405 mm 94.7 in
Width 600 mm 23.6 in
DepthDepth with z-bracket
200240
mmmm
7.99.4
inin
4) Weight 22.7 kg 50.0 lbs
Wind AreaFore/Aft 1.44 m2 15.5 ft2
Side 0.48 m2 5.2 ft2
Rated Wind Velocity (Safety factor 2.0)>206 km/hr >128 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 2059 N 463.0 lbsSide 782 N 175.7 lbs
Slant +/- 45° Dual Polarized, Panel 40° / 18 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80040/8CF __ 6°
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center 1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports ≤ -27 dB1) Gain 18 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 40°
E-Plane 7°1) Electrical Downtilt 6°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Length 2405 mm 94.7 in
Width 600 mm 23.6 in
DepthDepth with z-bracket
200240
mmmm
7.99.4
inin
4) Weight 22.7 kg 50.0 lbs
Wind AreaFore/Aft 1.44 m2 15.5 ft2
Side 0.48 m2 5.2 ft2
Rated Wind Velocity (Safety factor 2.0)>206 km/hr >128 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 2059 N 463.0 lbsSide 782 N 175.7 lbs
Slant +/- 45° Dual Polarized, Panel 63° / 10 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80063/2CF __
Revision Date: 7/30/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 604 mm 23.8 in
Width 285 mm 11.2 inDepthDepth with z-bracket
126166
mmmm
5.06.5
inin
4) Weight 2.2 kg 4.9 lbs
Wind AreaFore/Aft 0.18 m2 1.8 ft2
Side 0.08 m2 0.8 ft2
Rated Wind Velocity (Safety factor 2.0)>800 km/hr >500 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 248 N 56 lbsSide 110 N 25 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36211102
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 10 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 30°1) Electrical Downtilt 0°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 63° / 10 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80063/2CF __ 3°
Revision Date: 7/30/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 604 mm 23.8 in
Width 285 mm 11.2 inDepthDepth with z-bracket
126166
mmmm
5.06.5
inin
4) Weight 2.2 kg 4.9 lbs
Wind AreaFore/Aft 0.18 m2 1.8 ft2
Side 0.08 m2 0.8 ft2
Rated Wind Velocity (Safety factor 2.0)>800 km/hr >500 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 248 N 56 lbsSide 110 N 25 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36211102
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 10 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 30°1) Electrical Downtilt 3°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 63° / 10 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80063/2CF __ 5°
Revision Date: 7/30/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 604 mm 23.8 in
Width 285 mm 11.2 inDepthDepth with z-bracket
126166
mmmm
5.06.5
inin
4) Weight 2.2 kg 4.9 lbs
Wind AreaFore/Aft 0.18 m2 1.8 ft2
Side 0.08 m2 0.8 ft2
Rated Wind Velocity (Safety factor 2.0)>800 km/hr >500 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 248 N 56 lbsSide 110 N 25 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36211102
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 10 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 30°1) Electrical Downtilt 5°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 63° / 10 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80063/2CF __ 7°
Revision Date: 7/30/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 604 mm 23.8 in
Width 285 mm 11.2 inDepthDepth with z-bracket
126166
mmmm
5.06.5
inin
4) Weight 2.2 kg 4.9 lbs
Wind AreaFore/Aft 0.18 m2 1.8 ft2
Side 0.08 m2 0.8 ft2
Rated Wind Velocity (Safety factor 2.0)>800 km/hr >500 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 248 N 56 lbsSide 110 N 25 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36211102
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 10 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 30°1) Electrical Downtilt 7°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 63° / 10 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80063/2CF __ 9°
Revision Date: 7/30/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 604 mm 23.8 in
Width 285 mm 11.2 inDepthDepth with z-bracket
126166
mmmm
5.06.5
inin
4) Weight 2.2 kg 4.9 lbs
Wind AreaFore/Aft 0.18 m2 1.8 ft2
Side 0.08 m2 0.8 ft2
Rated Wind Velocity (Safety factor 2.0)>800 km/hr >500 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 248 N 56 lbsSide 110 N 25 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36211102
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 10 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 30°1) Electrical Downtilt 9°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 63° / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80063/4CF __
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1205 mm 47.4 in
Width 285 mm 11.2 in
DepthDepth with z-bracket
126166
mmmm
5.06.5
inin
4) Weight 4.5 kg 9.9 lbs
Wind AreaFore/Aft 0.36 m2 3.9 ft2
Side 0.15 m2 1.7 ft2
Rated Wind Velocity (Safety factor 2.0)>653 km/hr >406 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 522 N 117 lbsSide 244 N 54.5 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 13 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 15°1) Electrical Downtilt 0°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Refer to modelBXA-87063/4CF _.
Antenna available with center-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 63° / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80063/4CF __ 4°
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1205 mm 47.4 in
Width 285 mm 11.2 in
DepthDepth with z-bracket
126166
mmmm
5.06.5
inin
4) Weight 4.5 kg 9.9 lbs
Wind AreaFore/Aft 0.36 m2 3.9 ft2
Side 0.15 m2 1.7 ft2
Rated Wind Velocity (Safety factor 2.0)>653 km/hr >406 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 522 N 117 lbsSide 244 N 54.5 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 13 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 15°1) Electrical Downtilt 4°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 63° / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80063/4CF __ 5°
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1205 mm 47.4 in
Width 285 mm 11.2 in
DepthDepth with z-bracket
126166
mmmm
5.06.5
inin
4) Weight 4.5 kg 9.9 lbs
Wind AreaFore/Aft 0.36 m2 3.9 ft2
Side 0.15 m2 1.7 ft2
Rated Wind Velocity (Safety factor 2.0)>653 km/hr >406 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 522 N 117 lbsSide 244 N 54.5 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 13 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 15°1) Electrical Downtilt 5°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 63° / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80063/4CF __ 6°
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1205 mm 47.4 in
Width 285 mm 11.2 in
DepthDepth with z-bracket
126166
mmmm
5.06.5
inin
4) Weight 4.5 kg 9.9 lbs
Wind AreaFore/Aft 0.36 m2 3.9 ft2
Side 0.15 m2 1.7 ft2
Rated Wind Velocity (Safety factor 2.0)>653 km/hr >406 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 522 N 117 lbsSide 244 N 54.5 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 13 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 15°1) Electrical Downtilt 6°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 63° / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80063/6CF __
Revision Date: 11/21/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 11°1) Electrical Downtilt 0°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Refer to modelBXA-87063/6CF _.
Antenna available with center-fedconnectors only.
Length 1804 mm 71.1 in
Width 285 mm 11.2 in
DepthDepth with z-bracket
126166
mmmm
5.06.5
inin
4) Weight 6.8 kg 14.9 lbs
Wind AreaFore/Aft 0.51 m2 5.53 ft2
Side 0.23 m2 2.45 ft2
Rated Wind Velocity (Safety factor 2.0)>318 km/hr >198 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 753 N 169.2 lbsSide 378 N 85 lbs
Slant +/- 45° Dual Polarized, Panel 63° / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80063/6CF __ 2°
Revision Date: 11/21/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 11°1) Electrical Downtilt 2°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Length 1804 mm 71.1 in
Width 285 mm 11.2 in
DepthDepth with z-bracket
126166
mmmm
5.06.5
inin
4) Weight 6.8 kg 14.9 lbs
Wind AreaFore/Aft 0.51 m2 5.53 ft2
Side 0.23 m2 2.45 ft2
Rated Wind Velocity (Safety factor 2.0)>318 km/hr >198 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 753 N 169.2 lbsSide 378 N 85 lbs
Slant +/- 45° Dual Polarized, Panel 63° / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80063/6CF __ 3°
Revision Date: 11/21/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 11°1) Electrical Downtilt 3°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Length 1804 mm 71.1 in
Width 285 mm 11.2 in
DepthDepth with z-bracket
126166
mmmm
5.06.5
inin
4) Weight 6.8 kg 14.9 lbs
Wind AreaFore/Aft 0.51 m2 5.53 ft2
Side 0.23 m2 2.45 ft2
Rated Wind Velocity (Safety factor 2.0)>318 km/hr >198 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 753 N 169.2 lbsSide 378 N 85 lbs
Slant +/- 45° Dual Polarized, Panel 63° / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80063/6CF __ 5°
Revision Date: 11/21/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 11°1) Electrical Downtilt 5°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Length 1804 mm 71.1 in
Width 285 mm 11.2 in
DepthDepth with z-bracket
126166
mmmm
5.06.5
inin
4) Weight 6.8 kg 14.9 lbs
Wind AreaFore/Aft 0.51 m2 5.53 ft2
Side 0.23 m2 2.45 ft2
Rated Wind Velocity (Safety factor 2.0)>318 km/hr >198 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 753 N 169.2 lbsSide 378 N 85 lbs
Slant +/- 45° Dual Polarized, Panel 63° / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80063/6CF __ 6°
Revision Date: 11/21/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 11°1) Electrical Downtilt 6°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Length 1804 mm 71.1 in
Width 285 mm 11.2 in
DepthDepth with z-bracket
126166
mmmm
5.06.5
inin
4) Weight 6.8 kg 14.9 lbs
Wind AreaFore/Aft 0.51 m2 5.53 ft2
Side 0.23 m2 2.45 ft2
Rated Wind Velocity (Safety factor 2.0)>318 km/hr >198 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 753 N 169.2 lbsSide 378 N 85 lbs
Slant +/- 45° Dual Polarized, Panel 63° / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80063/6BF __ 15°
Revision Date: 11/21/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1804 mm 71.1 in
Width 285 mm 11.2 in
DepthDepth with z-bracket
126166
mmmm
5.06.5
inin
4) Weight 6.8 kg 14.9 lbs
Wind AreaFore/Aft 0.51 m2 5.53 ft2
Side 0.23 m2 2.45 ft2
Rated Wind Velocity (Safety factor 2.0)>318 km/hr >198 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 753 N 169.2 lbsSide 378 N 85 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / bottom1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 11°1) Electrical Downtilt 15°1) Null Fill 5%
Lightning Protection Direct Ground
BF Denotes a Bottom-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with bottom-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 63° / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80063/8CF __
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 2405 mm 94.7 in
Width 285 mm 11.2 in
DepthDepth with z-bracket
126166
mmmm
5.06.5
inin
4) Weight 10.9 kg 24.0 lbs
Wind AreaFore/Aft 0.70 m2 7.5 ft2
Side 0.30 m2 3.3 ft2
Rated Wind Velocity (Safety factor 2.0)>333 km/hr >207 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 1048 N 236 lbsSide 556 N 125 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < - 30 dB1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 7°1) Electrical Downtilt 0°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Refer to modelBXA-87063/8CF _.
Antenna available with center-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 63° / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80063/8CF __ 2°
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 2405 mm 94.7 in
Width 285 mm 11.2 in
DepthDepth with z-bracket
126166
mmmm
5.06.5
inin
4) Weight 10.9 kg 24.0 lbs
Wind AreaFore/Aft 0.70 m2 7.5 ft2
Side 0.30 m2 3.3 ft2
Rated Wind Velocity (Safety factor 2.0)>333 km/hr >207 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 1048 N 236 lbsSide 556 N 125 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < - 30 dB1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 7°1) Electrical Downtilt 2°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 63° / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80063/8CF __ 3°
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 2405 mm 94.7 in
Width 285 mm 11.2 in
DepthDepth with z-bracket
126166
mmmm
5.06.5
inin
4) Weight 10.9 kg 24.0 lbs
Wind AreaFore/Aft 0.70 m2 7.5 ft2
Side 0.30 m2 3.3 ft2
Rated Wind Velocity (Safety factor 2.0)>333 km/hr >207 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 1048 N 236 lbsSide 556 N 125 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < - 30 dB1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 7°1) Electrical Downtilt 3°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 63° / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80063/8CF __ 5°
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 2405 mm 94.7 in
Width 285 mm 11.2 in
DepthDepth with z-bracket
126166
mmmm
5.06.5
inin
4) Weight 10.9 kg 24.0 lbs
Wind AreaFore/Aft 0.70 m2 7.5 ft2
Side 0.30 m2 3.3 ft2
Rated Wind Velocity (Safety factor 2.0)>333 km/hr >207 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 1048 N 236 lbsSide 556 N 125 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < - 30 dB1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 7°1) Electrical Downtilt 5°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 80° / 12 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80080/4CF __
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1225 mm 48.2 in
Width 285 mm 11.2 in
DepthDepth with z-bracket
150190
mmmm
5.97.5
inin
4) Weight 6.5 kg 14.3 lbs
Wind AreaFore/Aft 0.35 m2 3.76 ft2
Side 0.18 m2 1.98 ft2
Rated Wind Velocity (Safety factor 2.0)>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 500 N 112.3 lbsSide 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 12 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 15°1) Electrical Downtilt 0°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 80° / 13.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80080/6CF __
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1844 mm 72.6 in
Width 285 mm 11.2 in
DepthDepth with z-bracket
116156
mmmm
4.66.1
inin
4) Weight 10 kg 22.0 lbs
Wind AreaFore/Aft 0.53 m2 5.7 ft2
Side 0.21 m2 2.3 ft2
Rated Wind Velocity (Safety factor 2.0)>277 km/hr >172 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 765 N 172 lbsSide 366 N 82 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 13.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 11°1) Electrical Downtilt 0°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 80° / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80080/8CF __
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 2450 mm 96.5 in
Width 285 mm 11.2 in
DepthDepth with z-bracket
150190
mmmm
5.97.5
inin
4) Weight 14 kg 31.0 lbs
Wind AreaFore/Aft 0.70 m2 7.50 ft2
Side 0.37 m2 3.96 ft2
Rated Wind Velocity (Safety factor 2.0)>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 1160 N 238 lbsSide 632 N 142 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 15 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 7°1) Electrical Downtilt 0°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 90° / 8 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80090/2CF __
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 604 mm 23.8 in
Width 204 mm 8.0 in
DepthDepth with z-bracket
145185
mmmm
5.77.3
inin
4) Weight 3.6 kg 8.0 lbs
Wind AreaFore/Aft 0.12 m2 1.3 ft2
Side 0.09 m2 0.9 ft2
Rated Wind Velocity (Safety factor 2.0)>800 km/hr >500 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 176 N 39.5 lbsSide 122 N 27.5 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36211102
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 8 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 90°
E-Plane 30°1) Electrical Downtilt 0°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 90° / 11 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80090/4CF __
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1205 mm 47.4 in
Width 205 mm 8.1 in
DepthDepth with z-bracket
145185
mmmm
5.77.3
inin
4) Weight 5.4 kg 12.0 lbs
Wind AreaFore/Aft 0.25 m2 2.7 ft2
Side 0.17 m2 1.9 ft2
Rated Wind Velocity (Safety factor 2.0)>679 km/hr >422 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 362 N 81.4 lbsSide 264 N 59.4 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 11 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 90°
E-Plane 15°1) Electrical Downtilt 0°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 90° / 11 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80090/4CF __ 2°
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1205 mm 47.4 in
Width 205 mm 8.1 in
DepthDepth with z-bracket
145185
mmmm
5.77.3
inin
4) Weight 5.4 kg 12.0 lbs
Wind AreaFore/Aft 0.25 m2 2.7 ft2
Side 0.17 m2 1.9 ft2
Rated Wind Velocity (Safety factor 2.0)>679 km/hr >422 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 362 N 81.4 lbsSide 264 N 59.4 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 11 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 90°
E-Plane 15°1) Electrical Downtilt 2°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 90° / 11 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80090/4CF __ 4°
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1205 mm 47.4 in
Width 205 mm 8.1 in
DepthDepth with z-bracket
145185
mmmm
5.77.3
inin
4) Weight 5.4 kg 12.0 lbs
Wind AreaFore/Aft 0.25 m2 2.7 ft2
Side 0.17 m2 1.9 ft2
Rated Wind Velocity (Safety factor 2.0)>679 km/hr >422 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 362 N 81.4 lbsSide 264 N 59.4 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 11 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 90°
E-Plane 15°1) Electrical Downtilt 4°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 90° / 12.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80090/6CF __
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1805 mm 71.1 in
Width 205 mm 8.1 in
DepthDepth with z-bracket
145185
mmmm
5.77.3
inin
4) Weight 8.2 kg 18.0 lbs
Wind AreaFore/Aft 0.37 m2 3.9 ft2
Side 0.26 m2 2.8 ft2
Rated Wind Velocity (Safety factor 2.0)>452 km/hr >281 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 558 N 126.0 lbsSide 433 N 97.4 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 12.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 90°
E-Plane 11°1) Electrical Downtilt 0°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 90° / 12.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80090/6CF __ 3°
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1805 mm 71.1 in
Width 205 mm 8.1 in
DepthDepth with z-bracket
145185
mmmm
5.77.3
inin
4) Weight 8.2 kg 18.0 lbs
Wind AreaFore/Aft 0.37 m2 3.9 ft2
Side 0.26 m2 2.8 ft2
Rated Wind Velocity (Safety factor 2.0)>452 km/hr >281 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 558 N 126.0 lbsSide 433 N 97.4 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 12.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 90°
E-Plane 11°1) Electrical Downtilt 3°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 90° / 12.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80090/6CF __ 4°
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 1805 mm 71.1 in
Width 205 mm 8.1 in
DepthDepth with z-bracket
145185
mmmm
5.77.3
inin
4) Weight 8.2 kg 18.0 lbs
Wind AreaFore/Aft 0.37 m2 3.9 ft2
Side 0.26 m2 2.8 ft2
Rated Wind Velocity (Safety factor 2.0)>452 km/hr >281 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 558 N 126.0 lbsSide 433 N 97.4 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 12.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 90°
E-Plane 11°1) Electrical Downtilt 4°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Slant +/- 45° Dual Polarized, Panel 90° / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80090/8CF __
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 14 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 90°
E-Plane 7°1) Electrical Downtilt 0°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Refer to modelBXA-87090/8CF _.
Antenna can be ordered with center-fed orbottom-fed connectors.
Center-fed: BXA-80090/8CF + (NE or E-DIN)Bottom-fed: BXA-80090/8BF + (NE or E-DIN)
Length 2405 mm 94.7 in
Width 205 mm 8.1 in
DepthDepth with z-bracket
145185
mmmm
5.77.3
inin
4) Weight 10.4 kg 23.0 lbs
Wind AreaFore/Aft 0.49 m2 5.3 ft2
Side 0.35 m2 3.8 ft2
Rated Wind Velocity (Safety factor 2.0)>323 km/hr >201 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 793 N 178.4 lbsSide 591 N 132.9 lbs
Slant +/- 45° Dual Polarized, Panel 90° / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80090/8BF __
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specificationsLength 2405 mm 94.7 in
Width 205 mm 8.1 in
DepthDepth with z-bracket
145185
mmmm
5.77.3
inin
4) Weight 10.4 kg 23.0 lbs
Wind AreaFore/Aft 0.49 m2 5.3 ft2
Side 0.35 m2 3.8 ft2
Rated Wind Velocity (Safety factor 2.0)>323 km/hr >201 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 793 N 178.4 lbsSide 591 N 132.9 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / bottomor center
1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 14 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 90°
E-Plane 7°1) Electrical Downtilt 0°1) Null Fill 5%
Lightning Protection Direct Ground
BF Denotes a Bottom-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna can be ordered with bottom-fed orcenter-fed connectors.
Bottom-fed: BXA-80090/8BF + (NE or E-DIN)Center-fed: BXA-80090/8CF + (NE or E-DIN)
Slant +/- 45° Dual Polarized, Panel 90° / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80090/8CF __ 3°
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 14 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 90°
E-Plane 7°1) Electrical Downtilt 3°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Length 2405 mm 94.7 in
Width 205 mm 8.1 in
DepthDepth with z-bracket
145185
mmmm
5.77.3
inin
4) Weight 10.4 kg 23.0 lbs
Wind AreaFore/Aft 0.49 m2 5.3 ft2
Side 0.35 m2 3.8 ft2
Rated Wind Velocity (Safety factor 2.0)>323 km/hr >201 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 793 N 178.4 lbsSide 591 N 132.9 lbs
Slant +/- 45° Dual Polarized, Panel 90° / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80090/8CF __ 4°
Revision Date: 7/20/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 14 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 90°
E-Plane 7°1) Electrical Downtilt 4°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Length 2405 mm 94.7 in
Width 205 mm 8.1 in
DepthDepth with z-bracket
145185
mmmm
5.77.3
inin
4) Weight 10.4 kg 23.0 lbs
Wind AreaFore/Aft 0.49 m2 5.3 ft2
Side 0.35 m2 3.8 ft2
Rated Wind Velocity (Safety factor 2.0)>323 km/hr >201 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 793 N 178.4 lbsSide 591 N 132.9 lbs
Slant +/- 45° Dual Polarized, Panel 90° / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
BXA-80090/8CF __ 5°
Revision Date: 7/3/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110-100 -90 -80
-70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,608,600 B2
Frequency Range 806-900 MHz*
Impedance 50Ω3) Connector(s) NE or E-DIN
2 ports / center1) VSWR ≤ 1.4:1
Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 14 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 90°
E-Plane 7°1) Electrical Downtilt 5°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
*Also available for 870-960 MHz. Consult yoursales director for more information.
Antenna available with center-fedconnectors only.
Length 2405 mm 94.7 in
Width 205 mm 8.1 in
DepthDepth with z-bracket
145185
mmmm
5.77.3
inin
4) Weight 10.4 kg 23.0 lbs
Wind AreaFore/Aft 0.49 m2 5.3 ft2
Side 0.35 m2 3.8 ft2
Rated Wind Velocity (Safety factor 2.0)>323 km/hr >201 mph
Wind Load @ 100 mph (161 km/hr)Fore/Aft 793 N 178.4 lbsSide 591 N 132.9 lbs
1300 Capital Drive Rockford, IL 61109 Toll-Free (888) 417-9562 Tel. (815) 399-0001 Fax. (815) 399-0156 Email: [email protected] www.antelinc.com
Mounting & Downtilt Bracket Kits
BXA Bracket Kits Part Number Bracket Type
36210002 Standard BXA Mounting Bracket Kit for: BXA-80040/4CF BXA-80080/4CF BXA-80040/6CF BXA-80080/6CF BXA-80040/8BF BXA-80080/8CF BXA-80040/8CF BXA-80090/2CF BXA-80063/2CF BXA-80090/4CF BXA-80063/4CF BXA-80090/6CF BXA-80063/6BF BXA-80090/8BF BXA-80063/6CF BXA-80090/8CF BXA-80063/8CF 36211102 Standard BXA *Downtilt Bracket Kit for: BXA-80063/2CF BXA-80090/2CF 36114003 Standard BXA *Downtilt Bracket Kit for: BXA-80040/4CF BXA-80080/4CF BXA-80040/6CF BXA-80080/6CF BXA-80040/8BF BXA-80080/8CF BXA-80040/8CF BXA-80090/4CF BXA-80063/4CF BXA-80090/6CF BXA-80063/6BF BXA-80090/8BF BXA-80063/6CF BXA-80090/8CF BXA-80063/8CF
*Both the downtilt bracket kit and the standard mounting bracket kit must be
ordered for mechanical downtilt applications.
Mounting Bracket Kits are sold separately and not included in the price of antennas.
R
WA
ANTE
NN
A
R
WA
ANTE
NN
A
36210002 Top View Side View
36211102 Top View Side View
R
WA
ANTE
NN
A
36114003 Top View Side View