bv series vane pump - jbj techniques limited
TRANSCRIPT
Versatility, power, compactness and low running costs are the main characteristics of B&C vanepumps. All the components subject to wear are contained in a cartridge unit that can be easily removedfor inspection and/or replacement without disconnecting the pump from the circuit, drastically reducingexpensive machine down time.The cartridge contains a rotor, vanes and inserts, a cam ring and two covers.During operation the rotor is driven by a splined shaftcoupled to the drive unit. As the rotation speed increases,centrifugal forces, in combination with the pressuregenerated behind the vanes, push the vanes outwards,where they follow the profile of the cam of the ring with asufficient contact pressure to ensure adequate hydraulicsealing. The two opposed pumping chambers formed bythe elliptical profile of the cam cancel out radial loads onthe shaft bearings, thereby giving them extremely longlifetimes.The versatility of the BV series pumps enables them tomeet the requirements of the most varied industrialapplications. In fact, as well as their proven high reliabilityand excellent volumetric efficiency in all working conditions,they operate with particularly low noise levels. This is madepossible by the special profile of the cam ring and the useof a 12 vane rotor that reduces the amplitude of the supplypressure pulses, thereby reducing induced vibrations (seedrawing).The BV series is available in four versions of single pump (from 8 to 230 l/min at 1200 rpm) and sixversions of double pump (from 55 to 370 l/min at 1200 rpm), with maximum powers of over 300 HP.The BV series pumps are extremely compact and are supplied with ISO norm mechanical couplingsand SAE norm hydraulic fittings. This makes them very easy to install and guarantees theirinterchangeability with other similar pumps.
FIXED DISPLACEMENT HYDRAULIC VANE PUMPS “BV” SERIES
1
BV
2
contents
Single pumps BV01.....................................
Single pumps BV02.....................................
Single pumps BV04.....................................
Single pumps BV05.....................................
Double pumps BV21.....................................
Double pumps BV41.....................................
Double pumps BV42.....................................
Double pumps BV51.....................................
Double pumps BV52.....................................
Double pumps BV54.....................................
Id. codes of cartridge kit components............
Operating instructions...................................
BV
pag. 3
pag. 11
pag. 18
pag. 25
pag. 32
pag. 42
pag. 52
pag. 61
pag. 71
pag. 80
pag. 89
pag. 91
3
Fixed displacement vane pump,hydraulically balanced, with capacitydetermined by the type of cartridge usedand the speed of rotation. The pump isavailable in six versions with capacitiesfrom 8 to 55 l/min (from 2 to 14 gpm) at1200 rpm and 7 bar.
General description
BV01single pump
Hydraulic fluids: antiwear high quality mineral oils or fire resistant fluid having same lubricationcapacities of the mineral oil.
Viscosity range (with mineral oil): from 13 to 860 cSt. (13 to 54 cSt. recommended).
Filtration: for the inlet - 149 micron abs., for the return line - 25 micron abs. or better (with syntheticfluids: for the return line - 10 micron abs. or better).
Inlet pressure: (with mineral oil): from -0,17 to +1,4 bar (-2.5 to + 20 psi)
Operating temperature: with mineral oil -10°C +70°C (+30°C to +60°C recommended), with water
based fluids +15°C to +50°C.
Drive: direct and coaxial by means of a flexible coupling.
Technical characteristcs
Cartridgemodel
Geometricdisplacement
Ratedcapacity
Ratedcapacity
Maximumpressure
Speedrangerpmat 1200 rpm 7 bar at 1500 rpm 7 bar with mineral oil
V01-02
V01-05
V01-08
V01-09
V01-11
V01-12
V01-14
cm3/g
7,2
18,0
27,4
30,1
36,4
39,5
45,9
(in3/r)
(0,44)
(1.10)
(1.67)
(1.83)
(2.22)
(2.41)
(2.79)
l/min
8,3
20,8
31,8
35,1
42,4
46,9
54,9
(gpm)
(2)
(5)
(8)
(9)
(11)
(12)
(14)
l/min
10,4
26,1
39,4
44,1
52,6
58,7
69,6
(gpm)
(2.8)
(6.9)
(10.4)
(11.7)
(13.9)
(15.5)
(18.4)
bar
210
210
210
210
210
160
140
min
600
600
600
600
600
600
600
max
1800
1800
1800
1800
1800
1800
1800
(psi)
(3050)
(3050)
(3050)
(3050)
(3050)
(2300)
(2030)
Sound level at 138 bar (2000 psi)
velocità
58
60
62
64
66
68
70
dB
(A)
1200 rpm 1500 rpm 1800 rpm
If the intake pressure is not zero bar, use the graph below to find the percentage correction factor toapply to the maximum speed
max speed / intake pipe pressure
% c
orr
ecti
on
fac
tor
for
the
max
sp
eed
106%
104%
102%
100%
98%
96%
94%
92%
-2,9 -1,45 0
PSI1,45 2,9 4,35
-0,2 -0,1 0 0,1 0,2 0,3 0,4
5,8
Intake pipe pressure (BAR)
max pressure / hydraulic fluid
Antiwear industrialhydraulic oil
Waterglycol
Water-in-oilemulsion
Main operating data
250
200
150
100
50
0
BA
R
3625
2900
2175
PS
I
1450
725
0
1214
1214
2, 5, 8,9, 11
2, 5, 8,9, 11 12 14
2, 5, 8, 9, 11
4
single pump BV01
max pres. Peak pres. (0,5 sec.max)
2000
1600
1200
800600400
0
RP
M
Antiwear industrialhydraulic oil
Syntetic fireresistant fluid
Waterglycol
Water-in-oilemulsion
1800
1400
200
1000
max speed / hydraulic fluid (with 0 bar in the intake pipe)
5
single pump BV01
Cartridge V01-02flow / pressure
PSI
l/min G
PM
16
6
2
0
0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200 250
14
2,8
12
8
BAR
20
4,16
KW
0
1
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
8,16
0
HP
0 50 100 150 200 250
power / pressure
3
5
7
8
5,44
2,72
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
100
NM
50
3040
BAR
5,2
3,12
1,04
10,9
4
10
18
2
4
6
20
Cartridge V01-05
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
80
40200
NM
BAR50
60
power / pressure
KW
0
2
4
6
8
10
12
14
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
21,6
16,2
10,8
5,4
0
HP
0 50 100 150 200 250
16
18
flow / pressurePSI
l/min
GP
M
45
35
15
10
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
10,4
7,8
5,2
0
0 50 100 150 200 250
2,6
40
30
25
20
5
1200 rpm
1500 rpm
1800 rpm
2500 rpm
6
BV01single pump
Cartridge V01-08flow / pressure
PSI
l/min G
PM
60
20
10
0
0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200 250
50
7,8
40
30
13
BAR
70
15,6
5,2
KW
0
5
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
27,2
0
HP
0 50 100 150 200 250
power / pressure
10
15
20
25
20,4
13,6
6,8
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
50
0
NM
50
100
150
BAR
18,2
10,4
2,6
34
Cartridge V01-09
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
50
0
NM
50
100
150
BAR
flow / pressurePSI
l/min G
PM
60
20
10
0
0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm1000 rpm
600 rpm
0
0 50 100 150 200 250
50
7,8
40
30
13
80
15,6
5,2
20,8
10,4
2,6
18,270
KW
0
5
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
27,2
0
HP
0 50 100 150 200 250
power / pressure
10
15
20
30
20,4
13,6
6,8
40,8
25 34
7
BV01single pump
Cartridge V01-11
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
150
50
0
NM
BAR50
100
power / pressure
KW
0
5
10
15
20
25
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
47,6
34
20,4
6,8
0
HP
0 50 100 150 200 250
30
35
flow / pressurePSI
l/min
GP
M
90
70
30
20
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
21,2
15,9
10,6
0
0 50 100 150 200 250
5,3
80
60
50
40
10
1200 rpm
1500 rpm
1800 rpm
2500 rpm
40,8
27,2
13,6
Cartridge V01-12flow / pressure
PSI
l/min G
PM
90
30
10
0
0 725 1450 2175 2900
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200
70
10,4
60
40
20,8
BAR
100
KW
0
5
BAR
PSI0 725 1450 2175 2900
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
34
0
HP
0 50 100 150 200
power / pressure
15
20
25
30
27,2
20,4
6,8
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200
input torque / pressure
0 725 1450 2175 2900
PSI
50
0
NM
50
100
150
BAR
26
15,6
5,2
40,8
80
50
20
10 13,6
BV01single pump
8
Installation dimensions mm (inches)
Approx. weight: 12 Kg. (26 lbs.)
Cartridge V01-14
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200
input torque / pressure
200
100
0
NM
BAR50
150
power / pressure
KW
0
5
10
15
20
25
BAR
PSI
0 725 1450 2175 2900
2500 rpm
1800 rpm
1500 rpm
1200 rpm1000 rpm
600 rpm
40,8
34
20,4
6,8
0
HP
0 50 100 150 200
30
flow / pressurePSI
l/min
GP
M
120
80
20
0
0 725 1450 2175 2900
1000 rpm
600 rpm
BAR
31,8
21,2
10,6
0
0 50 100 150 200
5,3
100
60
401200 rpm
1500 rpm
1800 rpm
2500 rpm
27,2
13,6
26,5
15,9
50
PSI
0 1450 2175 2900725
BV01
9
Model code breakdown
BV 01 G * * * * * (L) * (A)
Cartridge type02 05 08 09 11 12 14
Rotation(viewed from shaft end)L = left hand rotaton CCW (omit if CW)
Pump type
Outlet port positions(outlet viewed from cover end)
A = Outlet opposite endB = Outlet 90° CCW from inletC = Outlet in line with inletD = Outlet 90° CW from inlet
Mounting(omit if not required)
Shaft options mm (inches)
PORT ORIENTATIONS
Pump series Design Seals(omit with standard seals andone shaft-seal in NBR)V = seals and shaft-seal in FPM (Viton®)D = standard seals and double shaft-seals in NBRF = seals and double shaft-seals in FPM (Viton®)
Shaft end options01 = Straight with key (standard)11 = Splined90 = Splined SAE B
Spline data(shaft 11 and shaft 90)
Spline Involute side fit (ASA B5.15)Pressure angle 30°No. of teeth 13Pitch 16/32Major dia. 22.00 - 21.90 (0.866 - 0.862)Pitch dia. 20.638 (0.8125)Minor dia. 18.63 - 18.35 (0.733 - 0.722)Wildhaber 11.67 - 11.70 (0.459 - 0.461)
Shaft01
Shaft11
Shaft90
single pump
BV01
10
single pumpId
. cod
es o
f pum
p co
mpo
nent
s
Par
t N
o. M
8010
010
Bo
dy
Par
t N
o.
M80
2042
0To
rque
to 7
0 N
m (
625
lb. i
n.)
Scr
ew
Mo
del
01 11 90
Sh
aft
kit
Par
t N
o.
M80
1060
1M
8010
611
M80
1069
0
Mo
del
01 11 90
Sh
aft
Key
Par
t N
o.
K01
0100
0K
0111
000
K01
9000
0
Par
t N
o.
M80
1010
0- -
Par
t N
o.
M80
2006
0M
8020
065
M80
2006
1M
8020
066Sh
aft
seal Ty
pe
prim
ary
in N
BR
prim
ary
in F
PM
seco
ndar
y in
NB
Rse
cond
ary
in F
PM
Par
t N
o.
M80
1003
0
Bea
rin
g
Par
t N
o.
M80
2012
0
Co
ver
Par
t N
o.
M80
1004
0
See
ger
Pu
mp
sea
l kit
Typ
eN
BR
NB
RF
PM
(V
iton®
)F
PM
(V
iton®
)
Par
t N
o.
M80
1050
0M
8010
501
M80
1050
3M
8010
504
Par
tsse
als
+ 1
sha
ft se
alse
als
+ 2
sha
ft se
als
seal
s +
1 s
haft
seal
seal
s +
2 s
haft
seal
s
Par
t N
o.
M80
1005
0
See
ger
Car
trid
ge
Ser
ies
V01
V01
Mo
del
02 05 08 09 11 12 14 02 05 08 09 11 12 14
Par
t N
o.
V01
0200
2V
0105
015
V01
0803
5V
0109
055
V01
1107
5V
0112
095
V01
1411
5V
0102
007
V01
0502
5V
0108
045
V01
0906
5V
0111
085
V01
1210
5V
0114
125
Pu
mp
ro
tat.
right
han
d
left
hand
11
Fixed displacement vane pump,hydraulically balanced, with capacitydetermined by the type of cartridge usedand the speed of rotation. The pump isavailable in five versions with capacitiesfrom 47 to 79 l/min (from 12 to 21 gpm)at 1200 rpm and 7 bar.
General description
BV02
Hydraulic fluids: antiwear high quality mineral oils or fire resistant fluid having same lubricationcapacities of the mineral oil.
Viscosity range (with mineral oil): from 13 to 860 cSt. (13 to 54 cSt. recommended).
Filtration: for the inlet - 149 micron abs., for the return line - 25 micron abs. or better (with syntheticfluids: for the return line - 10 micron abs. or better).
Inlet pressure: (with mineral oil): from -0,17 to +1,4 bar (-2.5 to + 20 psi)
Operating temperature: with mineral oil -10°C +70°C (+30°C to +60°C recommended), with water
based fluids +15°C to +50°C.
Drive: direct and coaxial by means of a flexible coupling.
Technical characteristcs
Cartridgemodel
Geometricdisplacement
Ratedcapacity
Ratedcapacity
Maximumpressure
Speedrangerpmat 1200 rpm 7 bar at 1500 rpm 7 bar with mineral oil
single pump
V02-12
V02-14
V02-17
V02-19
V02-21
cm3/g
40,1
45,4
55,2
60,0
67,5
(in3/r)
(2.45)
(2.77)
(3.37)
(3.66)
(4.12)
l/min
46,9
52,7
64,2
71,0
79,0
(gpm)
(12)
(14)
(17)
(19)
(21)
l/min
58,8
65,7
80,2
88,7
99,8
(gpm)
(15.5)
(17.4)
(21.2)
(23.4)
(26.4)
bar
175
175
175
175
175
min
600
600
600
600
600
max
1800
1800
1800
1800
1800
(psi)
(2538)
(2538)
(2538)
(2538)
(2538)
BV02single pump
12
max pressure / hydraulic fluid
Antiwear industrialhydraulic oil
Syntetic fireresistant fluid
Waterglycol
max pres. Peak pres. (0,5 sec.max)
Water-in-oilemulsion
If the intake pressure is not zero bar, use the graph below to find the percentage correction factor toapply to the maximum speed
max speed / intake pipe pressure
Main operating data
250
200
150
100
50
0
BA
R3625
2900
2175
PS
I
1450
725
0
2000
1600
1200
800600400
0
RP
M
Antiwear industrialhydraulic oil
Syntetic fireresistant fluid
Waterglycol
Water-in-oilemulsion
1800
1400
200
1000
% c
orr
ecti
on
fac
tor
for
the
max
sp
eed
106%
104%
102%
100%
98%
96%
94%
92%
-2,9 -1,45 0
PSI1,45 2,9 4,35
-0,2 -0,1 0 0,1 0,2 0,3 0,4
5,8
max speed / hydraulic fluid (with 0 bar in the intake pipe)
Intake pipe pressure (BAR)
Sound level at 138 bar (2000 psi)
speed
58
60
62
64
66
68
70
dB
(A)
1200 rpm 1500 rpm 1800 rpm
13
BV02single pump
Cartridge V02-12
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure0 725 1450 2175 2900 3625
PSI
200
100500
NM
BAR50
150
power / pressure
KW
0
5
10
15
20
25
30
BAR
PSI0 725 1450 2175 2900 3625
1800 rpm
1500 rpm1200 rpm
1000 rpm
600 rpm
54,4
40,8
27,2
13,6
0
HP
0 50 100 150 200 250
35
40
flow / pressurePSI
l/min
GP
M
100
80
40
30
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
26
20,8
15,6
0
0 50 100 150 200 250
5,2
90
70
60
50
20
1200 rpm
1500 rpm
1800 rpm
2500 rpm
10
10,4
2500 rpm
Cartridge V02-14flow / pressure
PSI
l/min G
PM
100
20
0
0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200 250
80
10,4
60
40
20,8
BAR
120
26
5,2
KW
0
5
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
600 rpm
54,4
0
HP
0 50 100 150 200 250
power / pressure
10
15
40
50
40,8
27,2
13,6
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
100
0
NM
50
150200
BAR
31,2
15,6
68
45
30
25
35
20
50
1000 rpm
14
BV02single pump
Cartridge V02-17
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
250
150
500
NM
BAR50
200
power / pressure
KW
0
10
20
40
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
81,6
68
40,8
13,6
0
HP
0 50 100 150 200 250
50
60
flow / pressurePSI
l/min
GP
M
140
80
40
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
36,4
31,2
26
0
0 50 100 150 200 250
5,2
120
60
20
1200 rpm
1500 rpm
1800 rpm
2500 rpm
15,6
100
20,8
10,4
30
54,4
27,2
100
Cartridge V02-19flow / pressure
PSI
l/min G
PM
100
20
0
0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200 250
80
10,4
60
40
20,8
BAR
120
26
5,2
KW
0
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
54,4
0
HP
0 50 100 150 200 250
power / pressure
10
40
60
40,8
27,2
13,6
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
100
0
NM
50
200250
BAR
31,2
15,6
81,6
30
20
50
140
160
36,4
41,6
50 68
150
BV02single pump
15
Installation dimensions mm (inches)
Approx. weight: 15 Kg. (33 lbs.)
Cartridge V02-21
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
0
NM
BAR50
200
flow / pressurePSI
l/min
GP
M
140
80
40
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
42
31,5
21
0
0 50 100 150 200 250
120
60
20
1200 rpm
1500 rpm
1800 rpm
2500 rpm
100
10,5
100
160
180
300
power / pressure
KW
0
10
20
40
BAR
PSI
0 725 1450 2175 2900 3625
2500 rpm
1800 rpm1500 rpm
1200 rpm
1000 rpm
600 rpm
81,6
68
40,8
13,6
0
HP
0 50 100 150 200 250
50
70
30
54,4
27,2
60
95,2
BV02
16
Model code breakdown
BV 02 G * * * * * (L) * (A)
Cartridge type12 14 17 19 21
Rotation(viewed from shaft end)L = left hand rotaton CCW (omit if CW)
Pump type
Outlet port positions(outlet viewed from cover end)
A = Outlet opposite endB = Outlet 90° CCW from inletC = Outlet in line with inletD = Outlet 90° CW from inlet
Mounting(omit if not required)
Shaft options mm (inches)
PORT ORIENTATIONS
Pump series Design Seals(omit with standard seals andone shaft-seal in NBR)V = seals and shaft-seal in FPM (Viton®)D = standard seals and double shaft-seals in NBRF = seals and double shaft-seals in FPM (Viton®)
Shaft end options01 = Straight with key (standard), 11 = Splined86 = Heavy duty straight keyed, 90 = Splined SAE B
Spline data(shaft 11 and shaft 90)
Spline Involute side fit (ASA B5.15)Pressure angle 30°No. of teeth 13Pitch 16/32Major dia. 22.00 - 21.90 (0.866 - 0.862)Pitch dia. 20.638 (0.8125)Minor dia. 18.63 - 18.35 (0.733 - 0.722)Wildhaber 11.67 - 11.70 (0.459 - 0.461)
Shaft01
Shaft11
Shaft90
Shaft86
single pump
BV02
17
single pumpId
. cod
es o
f pum
p co
mpo
nent
s
Par
t N
o. M
8020
010
Bo
dy
Par
t N
o.
M80
2003
0
Bea
rin
g
Par
t N
o.
M80
2005
0
See
ger
Par
t N
o.
M80
2004
0
See
ger
Par
t N
o.
M80
2002
0
Co
ver
Par
t N
o.
M80
2006
0M
8020
065
M80
2006
1M
8020
066S
haf
t se
al Typ
epr
imar
y in
NB
Rpr
imar
y in
FP
Mse
cond
ary
in N
BR
seco
ndar
y in
FP
M
Pu
mp
sea
l kit
Typ
eN
BR
NB
RF
PM
(V
iton®
)F
PM
(V
iton®
)
Par
t N
o.
M80
2050
0M
8020
501
M80
2050
3M
8020
504
Par
tsse
als
+ 1
sha
ft se
alse
als
+ 2
sha
ft se
als
seal
s +
1 s
haft
seal
seal
s +
2 s
haft
seal
s
Car
trid
ge
Ser
ies
V02
V02
Mo
del
12 14 17 19 21 12 14 17 19 21
Par
t N
o.
V02
1203
0V
0214
070
V02
1711
0V
0219
150
V02
2119
0V
0212
040
V02
1408
0V
0217
120
V02
1916
0V
0221
200
Pu
mp
ro
tat.
right
han
d
left
hand
Mo
del
01 11 86 90
Sh
aft
kit
Par
t N
o.
M80
2060
1M
8020
611
M80
2068
6M
8020
690
Mo
del
01 11 86 90
Sh
aft
Key
Par
t N
o.
K02
0100
0K
0211
000
K02
8600
0K
0290
000
Co
dic
e N°
M80
1010
0-
M80
2860
0-
Par
t N
o.
M80
2007
0To
rque
to 1
02 N
m (
910
lb. i
n.)
Scr
ew
18
Fixed displacement vane pump,hydraulically balanced, with capacitydetermined by the type of cartridge usedand the speed of rotation. The pump isavailable in five versions with capacitiesfrom 80 to 140 l/min (from 21 to 38 gpm)at 1200 rpm and 7 bar.
General description
BV04
Hydraulic fluids: antiwear high quality mineral oils or fire resistant fluid having same lubricationcapacities of the mineral oil.
Viscosity range (with mineral oil): from 13 to 860 cSt. (13 to 54 cSt. recommended).
Filtration: for the inlet - 149 micron abs., for the return line - 25 micron abs. or better (with syntheticfluids: for the return line - 10 micron abs. or better).
Inlet pressure: (with mineral oil): from -0,17 to +1,4 bar (-2.5 to + 20 psi)
Operating temperature: with mineral oil -10°C +70°C (+30°C to +60°C recommended), with water
based fluids +15°C to +50°C.
Drive: direct and coaxial by means of a flexible coupling.
Technical characteristcs
Cartridgemodel
Geometricdisplacement
Ratedcapacity
Ratedcapacity
Maximumpressure
Speedrangerpmat 1200 rpm 7 bar at 1500 rpm 7 bar with mineral oil
single pump
V04-21
V04-25
V04-30
V04-35
V04-38
cm3/g
69,0
81,6
97,7
112,7
121,6
(in3/r)
(4.2)
(5)
(6)
(6.9)
(7.4)
l/min
79,5
94,0
113,8
131,6
139,9
(gpm)
(21)
(25)
(30)
(35)
(38)
l/min
101,4
120,1
141,2
167,2
177,3
(gpm)
(26.8)
(31.7)
(37.3)
(44.1)
(46.8)
bar
175
175
175
175
175
min
600
600
600
600
600
max
1800
1800
1800
1800
1800
(psi)
(2538)
(2538)
(2538)
(2538)
(2538)
BV04single pump
19
max pressure / hydraulic fluid
Antiwear industrialhydraulic oil
Syntetic fireresistant fluid
Waterglycol
max pres. peak pres. (0,5 sec.max)
Water-in-oilemulsion
max speed / hydraulic fluid (with 0 bar in the intake pipe)
If the intake pressure is not zero bar, use the graph below to find the percentage correction factor toapply to the maximum speed
max speed / intake pipe pressure
Main operating data
250
200
150
100
50
0
BA
R3625
2900
2175
PS
I
1450
725
0
2000
1600
1200
800600400
0
RP
M
Antiwear industrialhydraulic oil
Syntetic fireresistant fluid
Waterglycol
Water-in-oilemulsion
1800
1400
200
1000
% c
orr
ecti
on
fac
tor
for
the
max
sp
eed
110%
104%
102%
100%
98%
96%
94%
92%
-2,9 -1,45 0
PSI1,45 2,9 4,35
-0,2 -0,1 0 0,1 0,2 0,3 0,4
5,8
108%
106%
Intake pipe pressure (BAR)
Sound level at 138 bar (2000 psi)
speed
60
62
64
66
68
70
dB
(A)
1200 rpm 1500 rpm 1800 rpm
20
BV04single pump
Cartridge V04-21
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
300
0
NM
BAR50
200
power / pressure
KW
0
10
20
40
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm1500 rpm
1200 rpm
1000 rpm
600 rpm
108,8
81,6
0
HP
0 50 100 150 200 250
50
80
flow / pressurePSI
l/min
GP
M
180
80
40
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
42
31,5
0
0 50 100 150 200 250
120
60
20
1200 rpm
1500 rpm
1800 rpm
2500 rpm
100
21
10,5
30
54,4
27,2
100
140
160
70
60
Cartridge V04-25flow / pressure
PSI
l/min G
PM
100
0
0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200 250
50 13,2
BAR
150
26,4
KW
0
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm1500 rpm1200 rpm1000 rpm
600 rpm
81,6
0
HP
0 50 100 150 200 250
power / pressure
10
40
90
54,4
27,2
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
1000
NM
50
300400
BAR
39,6
30
20
200
250
52,8
66
50
108,8
200
60
80
70
21
BV04single pump
Cartridge V04-30
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
600
0
NM
BAR50
400
power / pressure
KW
0
20
40
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
136
0
HP
0 50 100 150 200 250
120
flow / pressurePSI
l/min
GP
M
250
50
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
66
39,6
0
0 50 100 150 200 250
150
1200 rpm
1500 rpm
1800 rpm
2500 rpm
100 26,4
13,2
81,6
27,2
200
200
60
52,8
80
100
108,8
54,4
Cartridge V04-35flow / pressure
PSI
l/min G
PM
100
0
0 725 1450 2175 2900 3625
2400 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200 250
50
13,2
BAR
150
26,4
KW
0
BAR
PSI0 725 1450 2175 2900 3625
2400 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
81,6
0
HP
0 50 100 150 200 250
power / pressure
40
120
54,4
27,2
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
0
NM
50
400
600
BAR
39,6
20
200
300
52,8
79,2
136
200
60
100
250 66
80 108,8
BV04single pump
22
Installation dimensions mm (inches)
Approx. weight: 23 Kg. (50 lbs.)
Cartridge V04-38
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
0
NM
BAR50
400
power / pressure
KW
0
20
40
BAR
PSI0 725 1450 2175 2900 3625
2400 rpm
1800 rpm
1500 rpm1200 rpm
1000 rpm
600 rpm
81,6
0
HP
0 50 100 150 200 250
140
flow / pressurePSI
l/min
GP
M
50
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
79,2
52,8
26,4
0
0 50 100 150 200 250
200
1200 rpm
1500 rpm
1800 rpm
2400 rpm
100
13,2
54,4
27,2
300
60
190,4
600
150 39,6 80
200
250 66
100
120 163,2
136
108,8
BV04
23
Model code breakdown
BV 04 G * * * * * (L) * (A)
Cartridge type21 25 30 35 38
Rotation(viewed from shaft end)L = left hand rotaton CCW (omit if CW)
Pump type
Outlet port positions(outlet viewed from cover end)
A = Outlet opposite endB = Outlet 90° CCW from inletC = Outlet in line with inletD = Outlet 90° CW from inlet
Mounting(omit if not required)
Shaft options mm (inches)
PORT ORIENTATIONS
Pump series Design Seals(omit with standard seals andone shaft-seal in NBR)V = seals and shaft-seal in FPM (Viton®)D = standard seals and double shaft-seals in NBRF = seals and double shaft-seals in FPM (Viton®)
Shaft end options01 = Straight with key (standard), 11 = Splined86 = Heavy duty straight keyed, 90 = Splined SAE C
Spline data(shaft 11 and shaft 90)
Spline Involute side fit (ASA B5.15)Pressure angle 30°No. of teeth 14Pitch 12/24Major dia. 31.60 - 31.50 (1.244 - 1.240)Pitch dia. 29.634 (1.1667)Minor dia. 26.99 - 26.66 (1.0627 - 1.05)Wildhaber 15.68 - 15.73 (0.617 - 0.619)
Shaft01
Shaft11
Shaft90
Shaft86
single pump
BV04
24
single pumpId
. cod
es o
f pum
p co
mpo
nent
s
Par
t N
o.
M80
4014
0
Bo
dy
Par
t N
o.
M80
4016
0
Bea
rin
g
Par
t N
o.
M80
4018
0
See
ger
Par
t N
o.
M80
4017
0
See
ger
Par
t N
o.
M80
4015
0
Co
ver
Par
t N
o.
M80
4020
0To
rque
to 2
25 N
m (2
010
lb. i
n.)
Scr
ew
Par
t N
o.
M80
4019
0M
8040
195
M80
4019
1M
8040
196Sh
aft
seal Ty
pe
prim
ary
in N
BR
prim
ary
in F
PM
seco
ndar
y in
NB
Rse
cond
ary
in F
PM
Pu
mp
sea
l kit
Typ
eN
BR
NB
RF
PM
(V
iton®
)F
PM
(V
iton®
)
Par
t N
o.
M80
4050
0M
8040
501
M80
4050
3M
8040
504
Par
tsse
als
+ 1
sha
ft se
alse
als
+ 2
sha
ft se
als
seal
s +
1 s
haft
seal
seal
s +
2 s
haft
seal
s
Car
trid
ge
Ser
ies
V04
V04
Mo
del
21 25 30 35 38 21 25 30 35 38
Par
t N
o.
V04
2103
0V
0425
070
V04
3011
0V
0435
150
V04
3819
0V
0421
040
V04
2508
0V
0430
120
V04
3516
0V
0438
200
Pu
mp
ro
tat.
right
han
d
left
hand
Mo
del
01 11 86 90
Sh
aft
kit
Par
t N
o.
M80
4060
1M
8040
611
M80
4068
6M
8040
690
Mo
del
01 11 86 90
Sh
aft
Key
Par
t N
o.
K04
0100
0K
0411
000
K04
8600
0K
0490
000
Par
t N
o.
M80
4010
0-
M80
4860
0-
25
Fixed displacement vane pump,hydraulically balanced, with capacitydetermined by the type of cartridge usedand the speed of rotation. The pump isavailable in five versions with capacitiesfrom 164 to 230 l/min (from 42 to 60gpm) at 1200 rpm and 7 bar.
General description
BV05
Hydraulic fluids: antiwear high quality mineral oils or fire resistant fluid having same lubricationcapacities of the mineral oil.
Viscosity range (with mineral oil): from 13 to 860 cSt. (13 to 54 cSt. recommended).
Filtration: for the inlet - 149 micron abs., for the return line - 25 micron abs. or better (with syntheticfluids: for the return line - 10 micron abs. or better).
Inlet pressure: (with mineral oil): from -0,17 to +1,4 bar (-2.5 to + 20 psi)
Operating temperature: with mineral oil -10°C +70°C (+30°C to +60°C recommended), with water
based fluids +15°C to +50°C.
Drive: direct and coaxial by means of a flexible coupling.
Technical characteristcs
Cartridgemodel
Geometricdisplacement
Ratedcapacity
Ratedcapacity
Maximumpressure
Speedrangerpmat 1200 rpm 7 bar at 1500 rpm 7 bar with mineral oil
single pump
V05-42
V05-47
V05-50
V05-57
V05-60
cm3/g
138,6
153,5
162,2
183,4
193,4
(in3/r)
(8.46)
(9.4)
(9.9)
(11.2)
(11.8)
l/min
164
180
189
217
230
(gpm)
(42)
(47)
(50)
(57)
(60)
l/min
203,4
222,7
234
267
285
(gpm)
(53.7)
(58.8)
(61.8)
(71.2)
(75.3)
bar
175
175
175
175
175
min
600
600
600
600
600
max
1800
1800
1800
1800
1800
(psi)
(2538)
(2538)
(2538)
(2538)
(2538)
BV05single pump
26
max pressure / hydraulic fluid
Antiwear industrialhydraulic oil
Syntetic fireresistant fluid
Waterglycol
max pres. peak pres. (0,5 sec.max)
Water-in-oilemulsion
max speed / hydraulic fluid (with 0 bar in the intake pipe)
If the intake pressure is not zero bar, use the graph below to find the percentage correction factor toapply to the maximum speed
max speed / intake pipe pressure
Main operating data
250
200
150
100
50
0
BA
R3625
2900
2175
PS
I
1450
725
0
2000
1600
1200
800600400
0
RP
M
Antiwear industrialhydraulic oil
Syntetic fireresistant fluid
Waterglycol
Water-in-oilemulsion
1800
1400
200
1000
% c
orr
ecti
on
fac
tor
for
the
max
sp
eed
120%
115%
110%
105%
100%
95%
90%
-2,9 -1,45 0
PSI1,45 2,9 4,35
-0,2 -0,1 0 0,1 0,2 0,3 0,4
5,8
Intake pipe pressure (BAR)
Sound level at 138 bar (2000 psi)
speed
64
66
68
70
72
dB
(A)
1200 rpm 1500 rpm 1800 rpm
27
BV05single pump
Cartridge V05-42
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200
input torque / pressure
0 725 1450 2175 2900
PSI
600
0
NM
BAR50
400
power / pressure
KW
0
20
40
BAR
PSI0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
135
0
HP
0 50 100 150 200
100
flow / pressurePSI
l/min
GP
M
300
50
0
0 725 1450 2175 2900
1000 rpm
600 rpm
BAR
79,2
39,6
0
0 50 100 150 200
1501200 rpm
1500 rpm
1800 rpm
2200 rpm
100 26,4
13,2
81
27
200
200
60
52,880
90
108
54
250 66
10
30
50
70
Cartridge V05-47flow / pressure
PSI
l/min G
PM
100
0
0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200
50 13,2
BAR
150
26,4
KW
0
BAR
PSI0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
81,3
0
HP
0 50 100 150 200
power / pressure
40
120
54,2
27,1
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200
input torque / pressure
0 725 1450 2175 2900
PSI
0
NM
50
400
600
BAR
39,6
20
200
350
52,8
92,4
135,5
200
60
100250 66
80 108,4
300 79,2162,6
28
BV05single pump
Cartridge V05-50
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200
input torque / pressure
0 725 1450 2175 2900
PSI
600
0
NM
BAR50
400
power / pressure
KW
0
20
40
BAR
PSI0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
162,6
0
HP
0 50 100 150 200
120
flow / pressurePSI
l/min
GP
M
350
50
0
0 725 1450 2175 2900
1000 rpm
600 rpm
BAR
92,4
39,6
0
0 50 100 150 200
150
1200 rpm
1500 rpm
1800 rpm
2200 rpm
100 26,4
13,2
81,3
27,1
200
200
60
52,880 108,4
54,2
250 66
300 79,2
100 135,5
Cartridge V05-57flow / pressure
PSI
l/min G
PM
100
0
0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm
1200 rpm1000 rpm
600 rpm
0
0 50 100 150 200
50 13,2
BAR
150
26,4
KW
0
BAR
PSI
0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
68
0
HP
0 50 100 150 200
power / pressure
25
125
34
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200
input torque / pressure
0 725 1450 2175 2900
PSI
0
NM
50
400
600
BAR
39,6
200
400
52,8
105,6
136
200
50
100
250 66
75 102
300 79,2
170350 92,4
BV05single pump
29
Installation dimensions mm (inches)
Approx. weight: 34 Kg. (75 lbs.)
Cartridge V05-60
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200
input torque / pressure
0 725 1450 2175 2900PSI
0
NM
BAR50
400
power / pressure
KW
0
20
40
BAR
PSI0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
81,6
0
HP
0 50 100 150 200
140
flow / pressurePSI
l/min
GP
M
50
0
0 725 1450 2175 2900
1000 rpm
600 rpm
BAR
118,8
52,8
26,4
0
0 50 100 150 200
200 1200 rpm
1500 rpm
1800 rpm
2200 rpm
100
13,2
54,4
27,2
450
60
190,4
600
150 39,6
80
200
250 66
100
120 163,2
136
108,8
300
400 105,6
92,4
79,2
350
Spline data(shaft 11 and shaft 90)
Spline Involute side fit (ASA B5.15)Pressure angle 30°No. of teeth 14Pitch 12/24Major dia. 31.60 - 31.50 (1.244 - 1.240)Pitch dia. 29.634 (1.1667)Minor dia. 26.99 - 26.66 (1.0627 - 1.05)Wildhaber 15.68 - 15.73 (0.617 - 0.619)
BV05
30
Model code breakdown
BV 05 G * * * * * (L) * (A)
Cartridge type42 47 50 57 60
Rotation(viewed from shaft end)L = left hand rotaton CCW (omit if CW)
Pump type
Outlet port positions(outlet viewed from cover end)
A = Outlet opposite endB = Outlet 90° CCW from inletC = Outlet in line with inletD = Outlet 90° CW from inlet
Mounting(omit if not required)
Shaft options mm (inches)
PORT ORIENTATIONS
Pump series Design Seals(omit with standard seals andone shaft-seal in NBR)V = seals and shaft-seal in FPM (Viton®)D = standard seals and double shaft-seals in NBRF = seals and double shaft-seals in FPM (Viton®)
Shaft end options01 = Straight with key (standard), 11 = Splined86 = Heavy duty straight keyed, 90 = Splined SAE C
Shaft01
Shaft11
Shaft90
Shaft86
single pump
BV05
31
single pumpId
. cod
es o
f pum
p co
mpo
nent
s
Par
t N
o.
M80
5025
0
Bo
dy
Par
t N
o.
M80
5027
0
Bea
rin
g
Par
t N
o.
M80
5031
0To
rque
to 3
98 N
m (
3550
lb. i
n.)
Scr
ew
Par
t N
o.
M80
5030
0M
8050
305
M80
5030
1M
8050
306S
haf
t se
al Typ
epr
imar
y in
NB
Rpr
imar
y in
FP
Mse
cond
ary
in N
BR
seco
ndar
y in
FP
M
Pu
mp
sea
l kit
Typ
eN
BR
NB
RF
PM
(V
iton®
)F
PM
(V
iton®
)
Par
t N
o.
M80
5050
0M
8050
501
M80
5050
3M
8050
504
Par
tsse
als
+ 1
sha
ft se
alse
als
+ 2
sha
ft se
als
seal
s +
1 s
haft
seal
seal
s +
2 s
haft
seal
s
Car
trid
ge
Ser
ies
V05
V05
Mo
del
42 47 50 57 60 42 47 50 57 60
Par
t N
o.
V05
4201
0V
0547
030
V05
5005
0V
0557
070
V05
6009
0V
0542
020
V05
4704
0V
0550
060
V05
5708
0V
0560
100
Pu
mp
ro
tat.
right
han
d
left
hand
Mo
del
01 11 86 90
Sh
aft
kit
Par
t N
o.
M80
5060
1M
8050
611
M80
5068
6M
8050
690
Mo
del
01 11 86 90
Sh
aft
Key
Par
t N
o.
K05
0100
0K
0511
000
K05
8600
0K
0590
000
Par
t N
o.
M80
5010
0-
M80
5860
0-
Par
t N
o.
M80
5029
0
See
ger
Par
t N
o.
M80
5028
0
See
ger
Par
t N
o.
M80
5026
0
Co
ver
BV21double pump
32
Fixed displacement vane pump,hydraulically balanced, with capacitydetermined by the cartridges used andthe speed of rotation. The pump isavailable in several versions with ratedcapacities from 55 to 134 l/min (from 14to 35 gpm) at 1200 rpm and 7 bar.
General description
Hydraulic fluids: antiwear high quality mineral oils or fire resistant fluid having same lubricationcapacities of the mineral oil.
Viscosity range (with mineral oil): from 13 to 860 cSt. (13 to 54 cSt. recommended).
Filtration: for the inlet - 149 micron abs., for the return line - 25 micron abs. or better (with syntheticfluids: for the return line - 10 micron abs. or better).
Inlet pressure: (with mineral oil): from -0,17 to +1,4 bar (-2.5 to + 20 psi)
Operating temperature: with mineral oil -10°C +70°C (+30°C to +60°C recommended), with waterbased fluids +15°C to +50°C.
Drive: direct and coaxial by means of a flexible coupling.
Technical characteristcs
Cartridgemodel
Geometricdisplacement
Ratedcapacity
Ratedcapacity
Maximumpressure
Speedrangerpmat 1200 rpm 7 bar at 1500 rpm 7 bar with mineral oil
shaft end
V02-12
V02-14
V02-17
V02-19
V02-21
cm3/g
40,1
45,4
55,2
60,1
67,5
(in3/r)
(2.45)
(2.77)
(3.37)
(3.66)
(4.12)
l/min
46,9
52,7
64,2
71,1
79,3
(gpm)
(12)
(14)
(17)
(19)
(21)
l/min
58,8
65,7
80,2
88,7
99,8
(gpm)
(15.5)
(17.4)
(21.2)
(23.4)
(26.4)
bar
175
175
175
175
175
min
600
600
600
600
600
max
1800
1800
1800
1800
1800
(psi)
(2538)
(2538)
(2538)
(2538)
(2538)
cover end
V01-02
V01-05
V01-08
V01-09
V01-11
V01-12
V01-14
cm3/g
7,2
18,0
27,4
30,1
36,4
39,5
45,9
(in3/r)
(0.44)
(1.10)
(1.67)
(1.83)
(2.22)
(2.41)
(2.79)
l/min
8,3
20,8
31,8
35,1
42,4
46,9
54,9
(gpm)
(2)
(5)
(8)
(9)
(11)
(12)
(14)
l/min
10,4
26,1
39,4
44,1
52,6
58,7
69,6
(gpm)
(2.8)
(6.9)
(10.4)
(11.7)
(13.9)
(15.5)
(18.4)
bar
210
210
210
210
210
160
140
min
600
600
600
600
600
600
600
max
2700
2700
2700
2700
2700
2700
2700
(psi)
(3050)
(3050)
(3050)
(3050)
(3050)
(2300)
(2030)
33
BV21double pump
Shaft end cartridge V02-12
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625
PSI
200
100500
NM
BAR50
150
power / pressure
KW
0
5
10
15
20
25
30
BAR
PSI0 725 1450 2175 2900 3625
1800 rpm
1500 rpm1200 rpm
1000 rpm
600 rpm
54,4
40,8
27,2
13,6
0
HP
0 50 100 150 200 250
35
40
flow / pressurePSI
l/min
GP
M
100
80
40
30
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
26
20,8
15,6
0
0 50 100 150 200 250
5,2
90
70
60
50
20
1200 rpm
1500 rpm
1800 rpm
2500 rpm
10
10,4
2500 rpm
If the intake pressure is not zero bar, use the graph below to find thepercentage correction factor to apply to the maximum speed
Main operating data
max pressure / hydraulic fluid
Antiwear industrialhydraulic oil
Syntetic fireresistant fluid
Waterglycol
max pres. peak pre. (0,5 sec.max)
Water-in-oilemulsion
250
200
150
100
50
0
BA
R
3625
2900
2175
PS
I
1450
725
0
2000
1600
1200
800600400
0
RP
M
Antiwear industrialhydraulic oil
Syntetic fireresistant fluid
Waterglycol
Water-in-oilemulsion
1800
1400
200
1000
max speed / hydraulic fluid (with 0 bar in the intake pipe)
speed
60
62
66
68
70
dB
(A)
Sound level at 138 bar (2000 psi)
64
max speed / intake pipe pressure%
co
rrec
tio
n f
acto
r fo
rth
e m
ax s
pee
d
106%
104%
102%
100%
98%
96%
94%
92%
-2,9 -1,45 0
PSI
1,45 2,9 4,35
-0,2 -0,1 0 0,1 0,2 0,3
Intake pipe pressure (BAR)0,4
5,8
1200 rpm 1500 rpm 1800 rpm
34
BV21double pump
Shaft end cartridge V02-14flow / pressure
PSI
l/min G
PM
100
20
0
0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200 250
80
10,4
60
40
20,8
BAR
120
26
5,2
KW
0
5
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
600 rpm
54,4
0
HP
0 50 100 150 200 250
power / pressure
10
15
40
50
40,8
27,2
13,6
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625
PSI
100
0
NM
50
150200
BAR
31,2
15,6
68
45
30
25
35
20
50
1000 rpm
Shaft end cartridge V02-17
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625
PSI
250
150
500
NM
BAR50
200
power / pressure
KW
0
10
20
40
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
81,6
68
40,8
13,6
0
HP
0 50 100 150 200 250
50
60
flow / pressurePSI
l/min
GP
M
140
80
40
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
36,4
31,2
26
0
0 50 100 150 200 250
5,2
120
60
20
1200 rpm
1500 rpm
1800 rpm
2500 rpm
15,6
100
20,8
10,4
30
54,4
27,2
100
35
BV21double pump
Shaft end cartridge V02-19flow / pressure
PSI
l/min G
PM
100
20
0
0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200 250
80
10,4
60
40
20,8
BAR
120
26
5,2
KW
0
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
54,4
0
HP
0 50 100 150 200 250
power / pressure
10
40
60
40,8
27,2
13,6
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
100
0
NM
50
200250
BAR
31,2
15,6
81,6
30
20
50
140
160
36,4
41,6
50 68
150
Shaft end cartridge V02-21
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625
PSI
0
NM
BAR50
200
power / pressure
KW
0
10
20
40
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
81,6
68
40,8
13,6
0
HP
0 50 100 150 200 250
50
70
flow / pressurePSI
l/min
GP
M
140
80
40
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
42
31,5
21
0
0 50 100 150 200 250
120
60
20
1200 rpm
1500 rpm
1800 rpm
2500 rpm
100
10,5
30
54,4
27,2
100
160
180
60
95,2
300
36
BV21double pump
Cartridge V01-02flow / pressure
PSI
l/min G
PM
16
6
2
0
0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200 250
14
2,8
12
8
BAR
20
4,16
KW
0
1
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
8,16
0
HP
0 50 100 150 200 250
power / pressure
3
5
7
8
5,44
2,72
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
100
NM
50
3040
BAR
5,2
3,12
1,04
10,9
4
10
18
2
4
6
20
Cartridge V01-05
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
80
40200
NM
BAR50
60
power / pressure
KW
0
2
4
6
8
10
12
14
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
21,6
16,2
10,8
5,4
0
HP
0 50 100 150 200 250
16
18
flow / pressurePSI
l/min
GP
M
45
35
15
10
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
10,4
7,8
5,2
0
0 50 100 150 200 250
2,6
40
30
25
20
5
1200 rpm
1500 rpm
1800 rpm
2500 rpm
37
BV21double pump
Cartridge V01-08flow / pressure
PSI
l/min G
PM
60
20
10
0
0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200 250
50
7,8
40
30
13
BAR
70
15,6
5,2
KW
0
5
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
27,2
0
HP
0 50 100 150 200 250
power / pressure
10
15
20
25
20,4
13,6
6,8
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
50
0
NM
50
100
150
BAR
18,2
10,4
2,6
34
Cartridge V01-09
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
50
0
NM
50
100
150
BAR
flow / pressurePSI
l/min G
PM
60
20
10
0
0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm1000 rpm
600 rpm
0
0 50 100 150 200 250
50
7,8
40
30
13
80
15,6
5,2
20,8
10,4
2,6
18,270
KW
0
5
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
27,2
0
HP
0 50 100 150 200 250
power / pressure
10
15
20
30
20,4
13,6
6,8
40,8
25 34
38
BV21double pump
Cover end cartridge V01-11
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
150
50
0
NM
BAR50
100
power / pressure
KW
0
5
10
15
20
25
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
47,6
34
20,4
6,8
0
HP
0 50 100 150 200 250
30
35
flow / pressurePSI
l/min
GP
M
90
70
30
20
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
21,2
15,9
10,6
0
0 50 100 150 200 250
5,3
80
60
50
40
10
1200 rpm
1500 rpm
1800 rpm
2500 rpm
40,8
27,2
13,6
Cover end cartridge V01-12flow / pressure
PSI
l/min G
PM
90
30
10
0
0 725 1450 2175 2900
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200
70
10,4
60
40
20,8
BAR
100
KW
0
5
BAR
PSI
0 725 1450 2175 2900
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
34
0
HP
0 50 100 150 200
power / pressure
15
20
25
30
27,2
20,4
6,8
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200
input torque / pressure
0 725 1450 2175 2900
PSI
50
0
NM
50
100
150
BAR
26
15,6
5,2
40,8
80
50
20
10 13,6
BV21
39
Installation dimensions mm (inches)
double pump
Approx. weight: 20,5 Kg. (45 lbs.)
Cover end cartridge V01-14
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200
input torque / pressure
200
100
0
NM
BAR50
150
power / pressure
KW
0
5
10
15
20
25
BAR
PSI0 725 1450 2175 2900
2500 rpm
1800 rpm
1500 rpm
1200 rpm1000 rpm
600 rpm
40,8
34
20,4
6,8
0
HP
0 50 100 150 200
30
flow / pressurePSI
l/min
GP
M
120
80
20
0
0 725 1450 2175 2900
1000 rpm
600 rpm
BAR
31,8
21,2
10,6
0
0 50 100 150 200
5,3
100
60
401200 rpm
1500 rpm
1800 rpm
2500 rpm
27,2
13,6
26,5
15,9
50
PSI
0 1450 2175 2900725
BV21double pump
40
Model code breakdown
BV 21 G * * * * * * * * (L) * (A)
Cartridge types-shaft end 12 14 17 19 21
-cover end 02 05 08 09 11 12 14
Rotation(viewed from shaft end)L = left hand rotaton CCW (omit if CW)
Pump type
Body outlet port positions(outlet viewed from cover end)A = Outlet opposite endB = Outlet 90° CCW from inletC = Outlet in line with inletD = Outlet 90° CW from inlet
Mounting(omit if not required)Pump series Design
Seals(omit with standard seals andone shaft-seal in NBR)V = seals and shaft-seal in FPM (Viton®)D = standard seals and double shaft-seals in NBRF = seals and double shaft-seals in FPM (Viton®)
Shaft end options01 = Straight with key (standard), 11 = Splined86 = Heavy duty straight keyed, 90 = Splined SAE B
Cover outlet port positions(outlet viewed from cover end)A = Outlet 135° CCW from inletB = Outlet 45° CCW from inletC = Outlet 45° CW from inletD = Outlet 135° CW from inlet
Shaft options mm (inches)
PORT ORIENTATIONS
Spline data(shaft 11 and shaft 90)
Spline Involute side fit (ASA B5.15)Pressure angle 30°No. of teeth 13Pitch 16/32Major dia. 22.00 - 21.90 (0.866 - 0.862)Pitch dia. 20.638 (0.8125)Minor dia. 18.63 - 18.35 (0.733 - 0.722)Wildhaber 11.67 - 11.70 (0.459 - 0.461)
Shaft01
Shaft11
Shaft90
Shaft86
BV21double pump
41
Id. c
odes
of p
ump
com
pone
nts
Par
t N
o.
M80
2001
0
Bo
dy
Par
t N
o.
M80
2003
0
Bea
rin
g
Par
t N
o.
M80
2005
0
See
ger
Par
t N
o.
M80
2004
0
See
ger
Par
t N
o.
M80
2042
0
Torq
ue to
70
Nm
(62
4 lb
. in.
)
Scr
ew
Par
t N
o.
M80
2006
0M
8020
065
M80
2006
1M
8020
066S
haf
t se
al Typ
epr
imar
y in
NB
Rpr
imar
y in
FP
Mse
cond
ary
in N
BR
seco
ndar
y in
FP
M
Pu
mp
sea
l kit
Typ
eN
BR
NB
RF
PM
(V
iton®
)F
PM
(V
iton®
)
Par
t N
o.
M82
1050
0M
8210
501
M82
1050
3M
8210
504
Par
tsse
als
+ 1
sha
ft se
alse
als
+ 2
sha
ft se
als
seal
s +
1 s
haft
seal
seal
s +
2 s
haft
seal
s
Mo
del
01 11 86 90
Sh
aft
kit
Par
t N
o.
M82
1060
1M
8210
611
M82
1068
6M
8210
690
Mo
del
01 11 86 90
Sh
aft
Key
Par
t N
o.
K21
0100
0K
2111
000
K21
8600
0K
2190
000
Par
t N
o.
M80
1010
0-
M80
2860
0-
Par
t N
o.
M80
2012
0
Cov
er
Par
t N
o.
M80
2013
0To
rque
to 1
02 N
m (
910
lb. i
n.)
Scr
ew
Par
t N
o.
M80
2011
0
Inle
t bod
y
Car
trid
ges
Ser
ies
V01
V01
Mo
del
02 05 08 09 11 12 14 02 05 08 09 11 12 14
Par
t N
o.
V01
0200
0V
0105
010
V01
0803
0V
0109
050
V01
1107
0V
0112
090
V01
1411
0V
0102
005
V01
0502
0V
0108
040
V01
0906
0V
0111
080
V01
1210
0V
0114
120
Ser
ies
V02
V02
Mo
del
12 14 17 19 21 12 14 17 19 21
Par
t N
o.
V02
1203
0V
0214
070
V02
1711
0V
0219
150
V02
2119
0
V02
1204
0V
0214
080
V02
1712
0V
0219
160
V02
2120
0
Pu
mp
ro
tati
on
right
han
d
left
hand
cove
r en
dsh
aft e
nd
42
Fixed displacement vane pump,hydraulically balanced, with capacitydetermined by the cartridges used andthe speed of rotation. The pump isavailable in several versions with ratedcapacities from 87 to 195 l/min(from 23 to 52 gpm) at 1200 rpm and 7 bar.
General description
Technical characteristcs
Cartridgemodel
Geometricdisplacement
Ratedcapacity
Ratedcapacity
Maximumpressure
Speedrangerpmat 1200 rpm 7 bar at 1500 rpm 7 bar with mineral oil
BV41double pump
shaft end
V04-21
V04-25
V04-30
V04-35
V04-38
cm3/g
69,0
81,6
97,7
112,7
121,6
(in3/r)
(4.2)
(5)
(6)
(6.9)
(7.4)
l/min
79,5
94,0
113,8
131,6
139,9
(gpm)
(21)
(25)
(30)
(35)
(38)
l/min
101,4
120,1
141,2
167,2
177,3
(gpm)
(26.8)
(31.7)
(37.3)
(44.1)
(46.8)
bar
175
175
175
175
175
min
600
600
600
600
600
max
1800
1800
1800
1800
1800
(psi)
(2538)
(2538)
(2538)
(2538)
(2538)
Hydraulic fluids: antiwear high quality mineral oils or fire resistant fluid having same lubricationcapacities of the mineral oil.
Viscosity range (with mineral oil): from 13 to 860 cSt. (13 to 54 cSt. recommended).
Filtration: for the inlet - 149 micron abs., for the return line - 25 micron abs. or better (with syntheticfluids: for the return line - 10 micron abs. or better).
Inlet pressure: (with mineral oil): from -0,17 to +1,4 bar (-2.5 to + 20 psi)
Operating temperature: with mineral oil -10°C +70°C (+30°C to +60°C recommended), with waterbased fluids +15°C to +50°C.
Drive: direct and coaxial by means of a flexible coupling.
cover end
V01-02
V01-05
V01-08
V01-09
V01-11
V01-12
V01-14
cm3/g
7,2
18,0
27,4
30,1
36,4
39,5
45,9
(in3/r)
(0.44)
(1.10)
(1.67)
(1.83)
(2.22)
(2.41)
(2.79)
l/min
8,3
20,8
31,8
35,1
42,4
46,9
54,9
(gpm)
(2)
(5)
(8)
(9)
(11)
(12)
(14)
l/min
10,4
26,1
39,4
44,1
52,6
58,7
69,6
(gpm)
(2.8)
(6.9)
(10.4)
(11.7)
(13.9)
(15.5)
(18.4)
bar
210
210
210
210
210
160
140
min
600
600
600
600
600
600
600
max
2700
2700
2700
2700
2700
2700
2700
(psi)
(3050)
(3050)
(3050)
(3050)
(3050)
(2300)
(2030)
BV41double pump
43
Shaft end cartridge V04-21
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625
PSI
300
0
NM
BAR50
200
power / pressure
KW
0
10
20
40
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm1500 rpm
1200 rpm
1000 rpm
600 rpm
108,8
81,6
0
HP
0 50 100 150 200 250
50
80
flow / pressurePSI
l/min
GP
M
180
80
40
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
42
31,5
0
0 50 100 150 200 250
120
60
20
1200 rpm
1500 rpm
1800 rpm
2500 rpm
100
21
10,5
30
54,4
27,2
100
140
160
70
60
If the intake pressure is not zero bar, use the graph below to find thepercentage correction factor to apply to the maximum speed
Main operating data
max pressure / hydraulic fluid
Antiwear industrialhydraulic oil
Syntetic fireresistant fluid
Waterglycol
max pres. peak pres. (0,5 sec.max)
Water-in-oilemulsion
250
200
150
100
50
0
BA
R
3625
2900
2175
PS
I
1450
725
0
2000
1600
1200
800600400
0
RP
M
Antiwear industrialhydraulic oil
Syntetic fireresistant fluid
Waterglycol
Water-in-oilemulsion
1800
1400
200
1000
max speed / hydraulic fluid (with 0 bar in the intake pipe)
speed
62
64
68
70
72
dB
(A)
Sound level at 138 bar (2000 psi)
66
max speed / intake pipe pressure%
co
rrec
tio
n f
acto
r fo
rth
e m
ax s
pee
d
110%
104%
102%
100%
98%
96%
94%
92%
-2,9 -1,45 0
PSI
1,45 2,9 4,35
-0,2 -0,1 0 0,1 0,2 0,3Intake pipe pressure (BAR)
0,4
5,8
1200 rpm 1500 rpm 1800 rpm
106%
108%
44
BV41double pump
Shaft end cartridge V04-30
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
600
0
NM
BAR50
400
power / pressure
KW
0
20
40
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
136
0
HP
0 50 100 150 200 250
120
flow / pressurePSI
l/min
GP
M
250
50
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
66
39,6
0
0 50 100 150 200 250
150
1200 rpm
1500 rpm
1800 rpm
2500 rpm
100 26,4
13,2
81,6
27,2
200
200
60
52,8
80
100
108,8
54,4
Shaft end cartridge V04-25flow / pressure
PSI
l/min G
PM
100
0
0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200 250
50 13,2
BAR
150
26,4
KW
0
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm1500 rpm1200 rpm1000 rpm
600 rpm
81,6
0
HP
0 50 100 150 200 250
power / pressure
10
40
90
54,4
27,2
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
1000
NM
50
300400
BAR
39,6
30
20
200
250
52,8
66
50
108,8
200
60
80
70
BV41double pump
45
Shaft end cartridge V04-35flow / pressure
PSI
l/min G
PM
100
0
0 725 1450 2175 2900 3625
2400 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200 250
50
13,2
BAR
150
26,4
KW
0
BAR
PSI0 725 1450 2175 2900 3625
2400 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
81,6
0
HP
0 50 100 150 200 250
power / pressure
40
120
54,4
27,2
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
0
NM
50
400
600
BAR
39,6
20
200
300
52,8
79,2
136
200
60
100
250 66
80 108,8
Shaft end cartridge V04-38
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625
PSI
0
NM
BAR50
400
power / pressure
KW
0
20
40
BAR
PSI0 725 1450 2175 2900 3625
2400 rpm
1800 rpm
1500 rpm1200 rpm
1000 rpm
600 rpm
81,6
0
HP
0 50 100 150 200 250
140
flow / pressurePSI
l/min
GP
M
50
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
79,2
52,8
26,4
0
0 50 100 150 200 250
200
1200 rpm
1500 rpm
1800 rpm
2400 rpm
100
13,2
54,4
27,2
300
60
190,4
600
150 39,6 80
200
250 66
100
120 163,2
136
108,8
BV41double pump
46
Cartridge V01-02flow / pressure
PSI
l/min G
PM
16
6
2
0
0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200 250
14
2,8
12
8
BAR
20
4,16
KW
0
1
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
8,16
0
HP
0 50 100 150 200 250
power / pressure
3
5
7
8
5,44
2,72
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
100
NM
50
3040
BAR
5,2
3,12
1,04
10,9
4
10
18
2
4
6
20
Cartridge V01-05
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
80
40200
NM
BAR50
60
power / pressure
KW
0
2
4
6
8
10
12
14
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
21,6
16,2
10,8
5,4
0
HP
0 50 100 150 200 250
16
18
flow / pressurePSI
l/min
GP
M
45
35
15
10
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
10,4
7,8
5,2
0
0 50 100 150 200 250
2,6
40
30
25
20
5
1200 rpm
1500 rpm
1800 rpm
2500 rpm
BV41double pump
47
Cartridge V01-08flow / pressure
PSI
l/min G
PM
60
20
10
0
0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200 250
50
7,8
40
30
13
BAR
70
15,6
5,2
KW
0
5
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
27,2
0
HP
0 50 100 150 200 250
power / pressure
10
15
20
25
20,4
13,6
6,8
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
50
0
NM
50
100
150
BAR
18,2
10,4
2,6
34
Cartridge V01-09
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
50
0
NM
50
100
150
BAR
flow / pressurePSI
l/min G
PM
60
20
10
0
0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm1000 rpm
600 rpm
0
0 50 100 150 200 250
50
7,8
40
30
13
80
15,6
5,2
20,8
10,4
2,6
18,270
KW
0
5
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
27,2
0
HP
0 50 100 150 200 250
power / pressure
10
15
20
30
20,4
13,6
6,8
40,8
25 34
BV41double pump
48
Cover end cartridge V01-11
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
150
50
0
NM
BAR50
100
power / pressure
KW
0
5
10
15
20
25
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
47,6
34
20,4
6,8
0
HP
0 50 100 150 200 250
30
35
flow / pressurePSI
l/min
GP
M
90
70
30
20
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
21,2
15,9
10,6
0
0 50 100 150 200 250
5,3
80
60
50
40
10
1200 rpm
1500 rpm
1800 rpm
2500 rpm
40,8
27,2
13,6
Cover end cartridge V01-12flow / pressure
PSI
l/min G
PM
90
30
10
0
0 725 1450 2175 2900
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200
70
10,4
60
40
20,8
BAR
100
KW
0
5
BAR
PSI
0 725 1450 2175 2900
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
34
0
HP
0 50 100 150 200
power / pressure
15
20
25
30
27,2
20,4
6,8
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200
input torque / pressure
0 725 1450 2175 2900
PSI
500
NM
50
100
150
BAR
26
15,6
5,2
40,8
80
50
20
10 13,6
BV41double pump
49
Installation dimensions mm (inches)
Approx. weight: 34 Kg. (75 lbs.)
Cover end cartridge V01-14
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200
input torque / pressure
200
100
0
NM
BAR50
150
power / pressure
KW
0
5
10
15
20
25
BAR
PSI0 725 1450 2175 2900
2500 rpm
1800 rpm
1500 rpm
1200 rpm1000 rpm
600 rpm
40,8
34
20,4
6,8
0
HP
0 50 100 150 200
30
flow / pressurePSI
l/min
GP
M
120
80
20
0
0 725 1450 2175 2900
1000 rpm
600 rpm
BAR
31,8
21,2
10,6
0
0 50 100 150 200
5,3
100
60
401200 rpm
1500 rpm
1800 rpm
2500 rpm
27,2
13,6
26,5
15,9
50
PSI
0 1450 2175 2900725
BV41double pump
Cartridge types-shaft end 21 25 30 35 38
-cover end 02 05 08 09 11 12 14
Shaft options mm (inches)
PORT ORIENTATIONS
Spline data(shaft 11 and shaft 90)
Spline Involute side fit (ASA B5.15)Pressure angle 30°No. of teeth 14Pitch 12/24Major dia. 31.60 - 31.50 (1.244 - 1.240)Pitch dia. 29.634 (1.1667)Minor dia. 26.99 - 26.66 (1.0627 - 1.05)Wildhaber 15.68 - 15.73 (0.617 - 0.619)
50
Shaft01
Shaft11
Shaft90
Shaft86
Model code breakdown
BV 41 G * * * * * * * * (L) * (A)
Rotation(viewed from shaft end)L = left hand rotaton CCW (omit if CW)
Pump type
Body outlet port positions(outlet viewed from cover end)A = Outlet opposite endB = Outlet 90° CCW from inletC = Outlet in line with inletD = Outlet 90° CW from inlet
Mounting(omit if not required)Pump series Design
Seals(omit with standard seals andone shaft-seal in NBR)V = seals and shaft-seal in FPM (Viton®)D = standard seals and double shaft-seals in NBRF = seals and double shaft-seals in FPM (Viton®)
Shaft end options01 = Straight with key (standard), 11 = Splined86 = Heavy duty straight keyed, 90 = Splined SAE C
Cover outlet port positions(outlet viewed from cover end)A = Outlet 135° CCW from inletB = Outlet 45° CCW from inletC = Outlet 45° CW from inletD = Outlet 135° CW from inlet
BV41double pump
51
Id. c
odes
of p
ump
com
pone
nts
Par
t N
o.
M80
4016
0
Bea
rin
g
Par
t N
o.
M80
4018
0
See
ger
Mo
del
01 11 86 90
Sh
aft
kit
Par
t N
o.
M84
1060
1M
8410
611
M84
1068
6M
8410
690
Mo
del
01 11 86 90
Sh
aft
Key
Par
t N
o.
K41
0100
0K
4111
000
K41
8600
0K
4190
000
Par
t N
o.
M80
4010
0-
M80
4860
0-
Par
t N
o.
M80
4014
0
Bo
dy
Par
t N
o.
M80
4043
0P
art
No
. M
8020
120
Co
ver
Par
t N
o.
M80
4021
0To
rque
to 2
25 N
m (
2010
lb. i
n.)
Scr
ewP
art
No
. M
8020
420
Torq
ue to
70
Nm
(62
4 lb
. in.
)
Scr
ew
Par
t N
o.
M80
4017
0
See
ger
Par
t N
o.
M80
4019
0M
8040
195
M80
4019
1M
8040
196S
haf
t se
al Typ
epr
imar
y in
NB
Rpr
imar
y in
FP
Mse
cond
ary
in N
BR
seco
ndar
y in
FP
M
Pu
mp
sea
l kit
Typ
eN
BR
NB
RF
PM
(V
iton®
)F
PM
(V
iton®
)
Par
t N
o.
M84
1050
0M
8410
501
M84
1050
3M
8410
504
Par
tsse
als
+ 1
sha
ft se
alse
als
+ 2
sha
ft se
als
seal
s +
1 s
haft
seal
seal
s +
2 s
haft
seal
s
Inle
t bod
y
Car
trid
ges
Ser
ies
V01
V01
Mo
del
02 05 08 09 11 12 14 02 05 08 09 11 12 14
Par
t N
o.
V01
0200
0V
0105
010
V01
0803
0V
0109
050
V01
1107
0V
0112
090
V01
1411
0V
0102
005
V01
0502
0V
0108
040
V01
0906
0V
0111
080
V01
1210
0V
0114
120
Ser
ies
V04
V04
Mo
del
21 25 30 35 38 21 25 30 35 38
Par
t N
o.
V04
2103
0V
0425
070
V04
3011
0V
0435
150
V04
3819
0
V04
2104
0V
0425
080
V04
3012
0V
0435
160
V04
3820
0
Pu
mp
ro
tati
on
right
han
d
left
hand
cove
r en
dsh
aft e
nd
Fixed displacement vane pump,hydraulically balanced, with capacitydetermined by the cartridges used andthe speed of rotation. The pump isavailable in several versions with ratedcapacities from 127 to 219 l/min(from 33 to 59 gpm) at 1200 rpm and 7 bar.
General description
BV42double pump
52
Hydraulic fluids: antiwear high quality mineral oils or fire resistant fluid having same lubricationcapacities of the mineral oil.
Viscosity range (with mineral oil): from 13 to 860 cSt. (13 to 54 cSt. recommended).
Filtration: for the inlet - 149 micron abs., for the return line - 25 micron abs. or better (with syntheticfluids: for the return line - 10 micron abs. or better).
Inlet pressure: (with mineral oil): from -0,17 to +1,4 bar (-2.5 to + 20 psi)
Operating temperature: with mineral oil -10°C +70°C (+30°C to +60°C recommended), with water
based fluids +15°C to +50°C.
Drive: direct and coaxial by means of a flexible coupling.
Technical characteristcs
Cartridgemodel
Geometricdisplacement
Ratedcapacity
Ratedcapacity
Maximumpressure
Speedrangerpmat 1200 rpm 7 bar at 1500 rpm 7 bar with mineral oil
shaft end
V04-21
V04-25
V04-30
V04-35
V04-38
cm3/g
69,0
81,6
97,7
112,7
121,6
(in3/r)
(4.2)
(5)
(6)
(6.9)
(7.4)
l/min
79,5
94,0
113,8
131,6
139,9
(gpm)
(21)
(25)
(30)
(35)
(38)
l/min
101,4
120,1
141,2
167,2
177,3
(gpm)
(26.8)
(31.7)
(37.3)
(44.1)
(46.8)
bar
175
175
175
175
175
min
600
600
600
600
600
max
1800
1800
1800
1800
1800
(psi)
(2538)
(2538)
(2538)
(2538)
(2538)
cover end
V02-12
V02-14
V02-17
V02-19
V02-21
cm3/g
40,1
45,4
55,2
60,0
67,5
(in3/r)
(2.45)
(2.77)
(3.37)
(3.66)
(4.12)
l/min
46,9
52,7
64,2
71,0
79,0
(gpm)
(12)
(14)
(17)
(19)
(21)
l/min
58,8
65,7
80,2
88,7
99,8
(gpm)
(15.5)
(17.4)
(21.2)
(23.4)
(26.4)
bar
175
175
175
175
175
min
600
600
600
600
600
max
1800
1800
1800
1800
1800
(psi)
(2538)
(2538)
(2538)
(2538)
(2538)
53
BV42double pump
If the intake pressure is not zero bar, use the graph below to find thepercentage correction factor to apply to the maximum speed
Main operating data
max pressure / hydraulic fluid
Antiwear industrialhydraulic oil
Syntetic fireresistant fluid
Waterglycol
max pres. peak pres. (0,5 sec.max)
Water-in-oilemulsion
250
200
150
100
50
0
BA
R
3625
2900
2175
PS
I
1450
725
0
2000
1600
1200
800600400
0
RP
M
Antiwear industrialhydraulic oil
Syntetic fireresistant fluid
Waterglycol
Water-in-oilemulsion
1800
1400
200
1000
max speed / hydraulic fluid (with 0 bar in the intake pipe)
speed
66
68
70
dB
(A)
Sound level at 138 bar (2000 psi)
64
Shaft end cartridge V04-21
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
300
0
NM
BAR50
200
power / pressure
KW
0
10
20
40
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm1500 rpm
1200 rpm
1000 rpm
600 rpm
108,8
81,6
0
HP
0 50 100 150 200 250
50
80
flow / pressurePSI
l/min
GP
M
180
80
40
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
42
31,5
0
0 50 100 150 200 250
120
60
20
1200 rpm
1500 rpm
1800 rpm
2500 rpm
100
21
10,5
30
54,4
27,2
100
140
160
70
60
max speed / intake pipe pressure%
co
rrec
tio
n f
acto
r fo
rth
e m
ax s
pee
d 106%
104%
102%
100%
98%
96%
94%
92%
-2,9 -1,45 0
PSI
1,45 2,9 4,35
-0,2 -0,1 0 0,1 0,2 0,3Intake pipe pressure (BAR)
0,4
5,8
72
1200 rpm 1500 rpm 1800 rpm
108%
110%
54
BV42double pump
Shaft end cartridge V04-30
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
600
0
NM
BAR50
400
power / pressure
KW
0
20
40
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
136
0
HP
0 50 100 150 200 250
120
flow / pressurePSI
l/min
GP
M
250
50
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
66
39,6
0
0 50 100 150 200 250
150
1200 rpm
1500 rpm
1800 rpm
2500 rpm
100 26,4
13,2
81,6
27,2
200
200
60
52,8
80
100
108,8
54,4
Shaft end cartridge V04-25flow / pressure
PSI
l/min G
PM
100
0
0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200 250
50 13,2
BAR
150
26,4
KW
0
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm1500 rpm1200 rpm1000 rpm
600 rpm
81,6
0
HP
0 50 100 150 200 250
power / pressure
10
40
90
54,4
27,2
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
1000
NM
50
300400
BAR
39,6
30
20
200
250
52,8
66
50
108,8
200
60
80
70
BV42double pump
55
Shaft end cartridge V04-35flow / pressure
PSI
l/min G
PM
100
0
0 725 1450 2175 2900 3625
2400 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200 250
50
13,2
BAR
150
26,4
KW
0
BAR
PSI
0 725 1450 2175 2900 3625
2400 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
81,6
0
HP
0 50 100 150 200 250
power / pressure
40
120
54,4
27,2
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
0
NM
50
400
600
BAR
39,6
20
200
300
52,8
79,2
136
200
60
100
250 66
80 108,8
Shaft end cartridge V04-38
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
0
NM
BAR50
400
power / pressure
KW
0
20
40
BAR
PSI0 725 1450 2175 2900 3625
2400 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
81,6
0
HP
0 50 100 150 200 250
140
flow / pressurePSI
l/min
GP
M
50
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
79,2
52,8
26,4
0
0 50 100 150 200 250
200
1200 rpm
1500 rpm
1800 rpm
2400 rpm
100
13,2
54,4
27,2
300
60
190,4
600
150 39,6 80
200
250 66
100
120 163,2
136
108,8
56
BV42double pump
Cover end cartridge V02-12
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
200
100500
NM
BAR50
150
power / pressure
KW
0
5
10
15
20
25
30
BAR
PSI0 725 1450 2175 2900 3625
1800 rpm
1500 rpm1200 rpm
1000 rpm
600 rpm
54,4
40,8
27,2
13,6
0
HP
0 50 100 150 200 250
35
40
flow / pressurePSI
l/min
GP
M
100
80
40
30
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
26
20,8
15,6
0
0 50 100 150 200 250
5,2
90
70
60
50
20
1200 rpm
1500 rpm
1800 rpm
2500 rpm
10
10,4
2500 rpm
Cover end cartridge V02-14flow / pressure
PSI
l/min G
PM
100
20
0
0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200 250
80
10,4
60
40
20,8
BAR
120
26
5,2
KW
0
5
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
600 rpm
54,4
0
HP
0 50 100 150 200 250
power / pressure
10
15
40
50
40,8
27,2
13,6
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
100
0
NM
50
150200
BAR
31,2
15,6
68
45
30
25
35
20
50
1000 rpm
57
BV42double pump
Cover end cartridge V02-17
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
250
150
500
NM
BAR50
200
power / pressure
KW
0
10
20
40
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
81,6
68
40,8
13,6
0
HP
0 50 100 150 200 250
50
60
flow / pressurePSI
l/min
GP
M
140
80
40
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
36,4
31,2
26
0
0 50 100 150 200 250
5,2
120
60
20
1200 rpm
1500 rpm
1800 rpm
2500 rpm
15,6
100
20,8
10,4
30
54,4
27,2
100
Cover end cartridge V02-19flow / pressure
PSI
l/min G
PM
100
20
0
0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200 250
80
10,4
60
40
20,8
BAR
120
26
5,2
KW
0
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
54,4
0
HP
0 50 100 150 200 250
power / pressure
10
40
60
40,8
27,2
13,6
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625
PSI
100
0
NM
50
200250
BAR
31,2
15,6
81,6
30
20
50
140
160
36,4
41,6
50 68
150
BV42
58
Installation dimensions mm (inches)
Approx. weight: 34,5 Kg. (76 lbs.)
double pump
Cover end cartridge V02-21
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
0
NM
BAR50
200
flow / pressurePSI
l/min
GP
M
140
80
40
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
42
31,5
21
0
0 50 100 150 200 250
120
60
20
1200 rpm
1500 rpm
1800 rpm
2500 rpm
100
10,5
100
160
180
300
power / pressure
KW
0
10
20
40
BAR
PSI
0 725 1450 2175 2900 3625
2500 rpm
1800 rpm1500 rpm
1200 rpm
1000 rpm
600 rpm
81,6
68
40,8
13,6
0
HP
0 50 100 150 200 250
50
70
30
54,4
27,2
60
95,2
BV42double pump
59
Cartridge types-shaft end 21 25 30 35 38
-cover end 12 14 17 19 21
Spline data(shaft 11 and shaft 90)
Spline Involute side fit (ASA B5.15)Pressure angle 30°No. of teeth 14Pitch 12/24Major dia. 31.60 - 31.50 (1.244 - 1.240)Pitch dia. 29.634 (1.1667)Minor dia. 26.99 - 26.66 (1.0627 - 1.05)Wildhaber 15.68 - 15.73 (0.617 - 0.619)
Shaft options mm (inches)
PORT ORIENTATIONS
Shaft01
Shaft11
Shaft90
Shaft86
Model code breakdown
BV 42 G * * * * * * * * (L) * (A)
Rotation(viewed from shaft end)L = left hand rotaton CCW (omit if CW)
Pump type
Body outlet port positions(outlet viewed from cover end)A = Outlet opposite endB = Outlet 90° CCW from inletC = Outlet in line with inletD = Outlet 90° CW from inlet
Mounting(omit if not required)Pump series Design
Seals(omit with standard seals andone shaft-seal in NBR)V = seals and shaft-seal in FPM (Viton®)D = standard seals and double shaft-seals in NBRF = seals and double shaft-seals in FPM (Viton®)
Shaft end options01 = Straight with key (standard), 11 = Splined86 = Heavy duty straight keyed, 90 = Splined SAE C
Cover outlet port positions(outlet viewed from cover end)A = Outlet 135° CCW from inletB = Outlet 45° CCW from inletC = Outlet 45° CW from inletD = Outlet 135° CW from inlet
BV42double pump
60
Id. c
odes
of p
ump
com
pone
nts
Par
t N
o. M
8040
140
Bo
dy
Par
t N
o.
M80
4016
0
Bea
rin
g
Par
t N
o.
M80
4018
0
See
ger
Par
t N
o.
M80
4017
0
See
ger
Par
t N
o.
M80
4023
0To
rque
to 1
02 N
m (
910
lb. i
n.)
Scr
ew
Par
t N
o.
M80
4019
0M
8040
195
M80
4019
1M
8040
196S
haf
t se
al Typ
epr
imar
y in
NB
Rpr
imar
y in
FP
Mse
cond
ary
in N
BR
seco
ndar
y in
FP
M
Pu
mp
sea
l kit
Typ
eN
BR
NB
RF
PM
(V
iton®
)F
PM
(V
iton®
)
Par
t N
o.
M84
2050
0M
8420
501
M84
2050
3M
8420
504
Par
tsse
als
+ 1
sha
ft se
alse
als
+ 2
sha
ft se
als
seal
s +
1 s
haft
seal
seal
s +
2 s
haft
seal
s
Car
trid
ges
Ser
ies
V02
V02
Mo
del
12 14 17 19 21 12 14 17 19 21
Par
t N
o.
V02
1201
0V
0214
050
V02
1709
0V
0219
130
V02
2117
0V
0212
020
V02
1406
0V
0217
100
V02
1914
0V
0221
180
Ser
ies
V04
V04
Mo
del
21 25 30 35 38 21 25 30 35 38
Par
t N
o.
V04
2103
0V
0425
070
V04
3011
0V
0435
150
V04
3819
0V
0421
040
V04
2508
0V
0430
120
V04
3516
0V
0438
200
Pu
mp
ro
tati
on
right
han
d
left
hand
cove
r en
dsh
aft e
nd
Par
t N
o.
M80
5035
0
Co
ver
Par
t N
o.
M80
4022
0To
rque
to 2
25 N
m (
2010
lb. i
n.)
Scr
ew
Par
t N
o.
M80
4024
0
Mo
del
01 11 86 90
Sh
aft
Key
Par
t N
o.
M80
4010
0-
M80
4860
0-
Mo
del
01 11 86 90
Sh
aft
kit
Par
t N
o.
M84
2060
1M
8420
611
M84
2068
6M
8420
690
Inte
l bod
y
Par
t N
o.
K42
0100
0K
4211
000
K42
8600
0K
4290
000
BV51double pump
Fixed displacement vane pump,hydraulically balanced, with capacitydetermined by the cartridges used andthe speed of rotation. The pump isavailable in several versions with ratedcapacities from 172 to 285 l/min(from 44 to 74 gpm) at 1200 rpm and 7 bar.
General description
61
Technical characteristcs
Cartridgemodel
Geometricdisplacement
Ratedcapacity
Ratedcapacity
Maximumpressure
Speedrangerpmat 1200 rpm 7 bar at 1500 rpm 7 bar awith mineral oil
Hydraulic fluids: antiwear high quality mineral oils or fire resistant fluid having same lubricationcapacities of the mineral oil.
Viscosity range (with mineral oil): from 13 to 860 cSt. (13 to 54 cSt. recommended).
Filtration: for the inlet - 149 micron abs., for the return line - 25 micron abs. or better (with syntheticfluids: for the return line - 10 micron abs. or better).
Inlet pressure: (with mineral oil): from -0,17 to +1,4 bar (-2.5 to + 20 psi)
Operating temperature: with mineral oil -10°C +70°C (+30°C to +60°C recommended), with waterbased fluids +15°C to +50°C.
Drive: direct and coaxial by means of a flexible coupling.
shaft end
V05-42
V05-47
V05-50
V05-57
V05-60
cm3/g
138,6
153,5
162,2
183,4
193,4
(in3/r)
(8.46)
(9.4)
(9.9)
(11.2)
(11.8)
l/min
164
180
189
217
230
(gpm)
(42)
(47)
(50)
(57)
(60)
l/min
203,4
222,7
234
267
285
(gpm)
(53.7)
(58.8)
(61.8)
(71.2)
(75.3)
bar
175
175
175
175
175
min
600
600
600
600
600
max
1800
1800
1800
1800
1800
(psi)
(2538)
(2538)
(2538)
(2538)
(2538)
cover end
V01-02
V01-05
V01-08
V01-09
V01-11
V01-12
V01-14
cm3/g
7,2
18,0
27,4
30,1
36,4
39,5
45,9
(in3/r)
(0.44)
(1.10)
(1.67)
(1.83)
(2.22)
(2.41)
(2.79)
l/min
8,3
20,8
31,8
35,1
42,4
46,9
54,9
(gpm)
(2)
(5)
(8)
(9)
(11)
(12)
(14)
l/min
10,4
26,1
39,4
44,1
52,6
58,7
69,6
(gpm)
(2.8)
(6.9)
(10.4)
(11.7)
(13.9)
(15.5)
(18.4)
bar
210
210
210
210
210
160
140
min
600
600
600
600
600
600
600
max
2700
2700
2700
2700
2700
2700
2700
(psi)
(3050)
(3050)
(3050)
(3050)
(3050)
(2300)
(2030)
62
BV51double pump
If the intake pressure is not zero bar, use the graph below to find thepercentage correction factor to apply to the maximum speed
Main operating data
max pressure / hydraulic fluid
Antiwear industrialhydraulic oil
Syntetic fireresistant fluid
Waterglycol
max pres. peak pres. (0,5 sec.max)
Water-in-oilemulsion
250
200
150
100
50
0
BA
R
3625
2900
2175
PS
I
1450
725
0
2000
1600
1200
800600400
0
RP
M
Antiwear industrialhydraulic oil
Syntetic fireresistant fluid
Waterglycol
Water-in-oilemulsion
1800
1400
200
1000
max speed / hydraulic fluid (with 0 bar in the intake pipe)
speed
65
69
71
73
dB
(A)
Sound level at 138 bar (2000 psi)
67
Shaft end cartridge V05-42
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200
input torque / pressure
0 725 1450 2175 2900
PSI
600
0
NM
BAR50
400
power / pressure
KW
0
20
40
BAR
PSI0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
135
0
HP
0 50 100 150 200
100
flow / pressurePSI
l/min
GP
M
300
50
0
0 725 1450 2175 2900
1000 rpm
600 rpm
BAR
79,2
39,6
0
0 50 100 150 200
1501200 rpm
1500 rpm
1800 rpm
2200 rpm
100 26,4
13,2
81
27
200
200
60
52,880
90
108
54
250 66
10
30
50
70
1200 rpm 1500 rpm 1800 rpm
max speed / intake pipe pressure%
co
rrec
tio
n f
acto
r fo
rth
e m
ax s
pee
d
120%
115%
110%
105%
100%
95%
90%
-2,9 -1,45 0
PSI
1,45 2,9 4,35
-0,2 -0,1 0 0,1 0,2 0,3Intake pipe pressure (BAR)
0,4
5,8
Shaft end cartridge V05-47flow / pressure
PSI
l/min G
PM
100
0
0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200
50 13,2
BAR
150
26,4
KW
0
BAR
PSI0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
81,3
0
HP
0 50 100 150 200
power / pressure
40
120
54,2
27,1
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200
input torque / pressure
0 725 1450 2175 2900PSI
0
NM
50
400
600
BAR
39,6
20
200
350
52,8
92,4
135,5
200
60
100250 66
80 108,4
300 79,2162,6
BV51double pump
63
Shaft end cartridge V05-50
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200
input torque / pressure
0 725 1450 2175 2900
PSI
600
0
NM
BAR50
400
power / pressure
KW
0
20
40
BAR
PSI0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
162,6
0
HP
0 50 100 150 200
120
flow / pressurePSI
l/min
GP
M
350
50
0
0 725 1450 2175 2900
1000 rpm
600 rpm
BAR
92,4
39,6
0
0 50 100 150 200
150
1200 rpm
1500 rpm
1800 rpm
2200 rpm
100 26,4
13,2
81,3
27,1
200
200
60
52,880 108,4
54,2
250 66
300 79,2
100 135,5
BV51double pump
64
Shaft end cartridge V05-57flow / pressure
PSI
l/min G
PM
100
0
0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm
1200 rpm1000 rpm
600 rpm
0
0 50 100 150 200
50 13,2
BAR
150
26,4
KW
0
BAR
PSI0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
68
0
HP
0 50 100 150 200
power / pressure
25
125
34
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200
input torque / pressure
0 725 1450 2175 2900PSI
0
NM
50
400
600
BAR
39,6
200
400
52,8
105,6
136
200
50
100
250 66
75 102
300 79,2
170350 92,4
Shaft end cartridge V05-60
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200
input torque / pressure
0 725 1450 2175 2900
PSI
0
NM
BAR50
400
power / pressure
KW
0
20
40
BAR
PSI0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
81,6
0
HP
0 50 100 150 200
140
flow / pressurePSI
l/min
GP
M
50
0
0 725 1450 2175 2900
1000 rpm
600 rpm
BAR
118,8
52,8
26,4
0
0 50 100 150 200
200 1200 rpm
1500 rpm
1800 rpm
2200 rpm
100
13,2
54,4
27,2
450
60
190,4
600
150 39,6
80
200
250 66
100
120 163,2
136
108,8
300
400 105,6
92,4
79,2
350
BV51double pump
65
Cartridge V01-02flow / pressure
PSI
l/min G
PM
16
6
2
0
0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200 250
14
2,8
12
8
BAR
20
4,16
KW
0
1
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
8,16
0
HP
0 50 100 150 200 250
power / pressure
3
5
7
8
5,44
2,72
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
100
NM
50
3040
BAR
5,2
3,12
1,04
10,9
4
10
18
2
4
6
20
Cartridge V01-05
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
80
40200
NM
BAR50
60
power / pressure
KW
0
2
4
6
8
10
12
14
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
21,6
16,2
10,8
5,4
0
HP
0 50 100 150 200 250
16
18
flow / pressurePSI
l/min
GP
M
45
35
15
10
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
10,4
7,8
5,2
0
0 50 100 150 200 250
2,6
40
30
25
20
5
1200 rpm
1500 rpm
1800 rpm
2500 rpm
BV51double pump
66
Cartridge V01-08flow / pressure
PSI
l/min G
PM
60
20
10
0
0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200 250
50
7,8
40
30
13
BAR
70
15,6
5,2
KW
0
5
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
27,2
0
HP
0 50 100 150 200 250
power / pressure
10
15
20
25
20,4
13,6
6,8
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
50
0
NM
50
100
150
BAR
18,2
10,4
2,6
34
Cartridge V01-09
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
50
0
NM
50
100
150
BAR
flow / pressurePSI
l/min G
PM
60
20
10
0
0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm1000 rpm
600 rpm
0
0 50 100 150 200 250
50
7,8
40
30
13
80
15,6
5,2
20,8
10,4
2,6
18,270
KW
0
5
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
27,2
0
HP
0 50 100 150 200 250
power / pressure
10
15
20
30
20,4
13,6
6,8
40,8
25 34
Cover end cartridge V01-11
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
150
50
0
NM
BAR50
100
power / pressure
KW
0
5
10
15
20
25
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
47,6
34
20,4
6,8
0
HP
0 50 100 150 200 250
30
35
flow / pressurePSI
l/min
GP
M
90
70
30
20
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
21,2
15,9
10,6
0
0 50 100 150 200 250
5,3
80
60
50
40
10
1200 rpm
1500 rpm
1800 rpm
2500 rpm
40,8
27,2
13,6
Cover end cartridge V01-12flow / pressure
PSI
l/min G
PM
90
30
10
0
0 725 1450 2175 2900
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200
70
10,4
60
40
20,8
BAR
100
KW
0
5
BAR
PSI
0 725 1450 2175 2900
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
34
0
HP
0 50 100 150 200
power / pressure
15
20
25
30
27,2
20,4
6,8
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200
input torque / pressure
0 725 1450 2175 2900
PSI
50
0
NM
50
100
150
BAR
26
15,6
5,2
40,8
80
50
20
10 13,6
67
BV51double pump
Cover end cartridge V01-14
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200
input torque / pressure
200
100
0
NM
BAR50
150
power / pressure
KW
0
5
10
15
20
25
BAR
PSI0 725 1450 2175 2900
2500 rpm
1800 rpm
1500 rpm
1200 rpm1000 rpm
600 rpm
40,8
34
20,4
6,8
0
HP
0 50 100 150 200
30
flow / pressurePSI
l/min
GP
M
120
80
20
0
0 725 1450 2175 2900
1000 rpm
600 rpm
BAR
31,8
21,2
10,6
0
0 50 100 150 200
5,3
100
60
401200 rpm
1500 rpm
1800 rpm
2500 rpm
27,2
13,6
26,5
15,9
50
68
Installation dimensions mm (inches)
Approx. weight: 43 Kg. (95 lbs.)
BV51double pump
PSI0 1450 2175 2900725
Spline data(shaft 11 and shaft 90)
Spline Involute side fit (ASA B5.15)Pressure angle 30°No. of teeth 14Pitch 12/24Major dia. 31.60 - 31.50 (1.244 - 1.240)Pitch dia. 29.634 (1.1667)Minor dia. 26.99 - 26.66 (1.0627 - 1.05)Wildhaber 15.68 - 15.73 (0.617 - 0.619)
Shaft options mm (inches)
PORT ORIENTATIONS
Cartridge types-shaft end 42 47 50 57 60
-cover end 02 05 08 09 11 12 14
BV51double pump
69
Shaft01
Shaft11
Shaft90
Shaft86
Model code breakdown
BV 51 G * * * * * * * * (L) * (A)
Rotation(viewed from shaft end)L = left hand rotaton CCW (omit if CW)
Pump type
Body outlet port positions(outlet viewed from cover end)A = Outlet opposite endB = Outlet 90° CCW from inletC = Outlet in line with inletD = Outlet 90° CW from inlet
Mounting(omit if not required)Pump series Design
Seals(omit with standard seals andone shaft-seal in NBR)V = seals and shaft-seal in FPM (Viton®)D = standard seals and double shaft-seals in NBRF = seals and double shaft-seals in FPM (Viton®)
Shaft end options01 = Straight with key (standard), 11 = Splined86 = Heavy duty straight keyed, 90 = Splined SAE C
Cover outlet port positions(outlet viewed from cover end)A = Outlet 135° CCW from inletB = Outlet 45° CCW from inletC = Outlet 45° CW from inletD = Outlet 135° CW from inlet
BV51double pump
70
Id. c
odes
of p
ump
com
pone
nts
Par
t N
o.
M80
5025
0
Bo
dy
Par
t N
o.
M80
5027
0
Bea
rin
g
Par
t N
o.
M80
5029
0
See
ger
Par
t N
o.
M80
2042
0To
rque
to 7
0 N
m (
624
lb. i
n.)
Scr
ew
Par
t N
o.
M80
5030
0M
8050
305
M80
5030
1M
8050
306S
haf
t se
al Typ
epr
imar
y in
NB
Rpr
imar
y in
FP
Mse
cond
ary
in N
BR
seco
ndar
y in
FP
M
Pu
mp
sea
l kit
Typ
eN
BR
NB
RF
PM
(V
iton®
)F
PM
(V
iton®
)
Par
t N
o.
M85
1050
0M
8510
501
M85
1050
3M
8510
504
Par
tsse
als
+ 1
sha
ft se
alse
als
+ 2
sha
ft se
als
seal
s +
1 s
haft
seal
seal
s +
2 s
haft
seal
s
Par
t N
o.
M80
2012
0
Cov
erP
art
No
. M
8050
390
Mo
del
01 11 86 90
Sh
aft
Key
Par
t N
o.
K51
0100
0K
5111
000
K51
8600
0K
5190
000
Par
t N
o.
M80
5010
0-
M80
5860
0-
Mo
del
01 11 86 90
Sh
aft
kit
Par
t N
o.
M85
1060
1M
8510
611
M85
1068
6M
8510
690
Inle
t bod
y
See
ger
Par
t N
o.
M80
5028
0
Par
t N
o.
M80
5032
0To
rque
to 3
98 N
m (
3550
lb. i
n.)
Scr
ew
Car
trid
ges
Ser
ies
V01
V01
Mo
del
02 05 08 09 11 12 14 02 05 08 09 11 12 14
Par
t N
o.
V01
0200
0V
0105
010
V01
0803
0V
0109
050
V01
1107
0V
0112
090
V01
1411
0V
0102
005
V01
0502
0V
0108
040
V01
0906
0V
0111
080
V01
1210
0V
0114
120
Ser
ies
V05
V05
Mo
del
42 47 50 57 60 42 47 50 57 60
Par
t N
o.
V05
4201
0V
0547
030
V05
5005
0V
0557
070
V05
6009
0
V05
4202
0V
0547
040
V05
5006
0V
0557
080
V05
6010
0
Pu
mp
ro
tati
on
right
han
d
left
hand
cove
r en
dsh
aft e
nd
Fixed displacement vane pump,hydraulically balanced, with capacitydetermined by the cartridges used andthe speed of rotation. The pump isavailable in several versions with ratedcapacities from 211 to 309 l/min(from 54 to 81 gpm) at 1200 rpm and 7 bar.
General description
Hydraulic fluids: antiwear high quality mineral oils or fire resistant fluid having same lubricationcapacities of the mineral oil.
Viscosity range (with mineral oil): from 13 to 860 cSt. (13 to 54 cSt. recommended).
Filtration: for the inlet - 149 micron abs., for the return line - 25 micron abs. or better (with syntheticfluids: for the return line - 10 micron abs. or better).
Inlet pressure: (with mineral oil): from -0,17 to +1,4 bar (-2.5 to + 20 psi)
Operating temperature: with mineral oil -10°C +70°C (+30°C to +60°C recommended), with water
based fluids +15°C to +50°C.
Drive: direct and coaxial by means of a flexible coupling.
Technical characteristcs
Cartridgemodel
Geometricdisplacement
Ratedcapacity
Ratedcapacity
Maximumpressure
Speedrangerpmat 1200 rpm 7 bar at 1500 rpm 7 bar with mineral oil
BV52double pump
71
shaft end
V05-42
V05-47
V05-50
V05-57
V05-60
cm3/g
138,6
153,5
162,2
183,4
193,4
(in3/r)
(8.46)
(9.4)
(9.9)
(11.2)
(11.8)
l/min
164
180
189
217
230
(gpm)
(42)
(47)
(50)
(57)
(60)
l/min
203,4
222,7
234
267
285
(gpm)
(53.7)
(58.8)
(61.8)
(71.2)
(75.3)
bar
175
175
175
175
175
min
600
600
600
600
600
max
1800
1800
1800
1800
1800
(psi)
(2538)
(2538)
(2538)
(2538)
(2538)
cover end
V02-12
V02-14
V02-17
V02-19
V02-21
cm3/g
40,1
45,4
55,2
60,0
67,5
(in3/r)
(2.45)
(2.77)
(3.37)
(3.66)
(4.12)
l/min
46,9
52,7
64,2
71,0
79,0
(gpm)
(12)
(14)
(17)
(19)
(21)
l/min
58,8
65,7
80,2
88,7
99,8
(gpm)
(15.5)
(17.4)
(21.2)
(23.4)
(26.4)
bar
175
175
175
175
175
min
600
600
600
600
600
max
1800
1800
1800
1800
1800
(psi)
(2538)
(2538)
(2538)
(2538)
(2538)
BV52double pump
72
If the intake pressure is not zero bar, use the graph below to find thepercentage correction factor to apply to the maximum speed
Main operating data
max pressure / hydraulic fluid
Antiwear industrialhydraulic oil
Syntetic fireresistant fluid
Waterglycol
max pres. peak pres. (0,5 sec.max)
Water-in-oilemulsion
250
200
150
100
50
0
BA
R
3625
2900
2175
PS
I
1450
725
0
2000
1600
1200
800600400
0
RP
M
Antiwear industrialhydraulic oil
Syntetic fireresistant fluid
Waterglycol
Water-in-oilemulsion
1800
1400
200
1000
max speed / hydraulic fluid (with 0 bar in the intake pipe)
speed
66
68
72
74
dB
(A)
Sound level at 138 bar (2000 psi)
70
Shaft end cartridge V05-42
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200
input torque / pressure
0 725 1450 2175 2900
PSI
600
0
NM
BAR50
400
power / pressure
KW
0
20
40
BAR
PSI0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
135
0
HP
0 50 100 150 200
100
flow / pressurePSI
l/min
GP
M
300
50
0
0 725 1450 2175 2900
1000 rpm
600 rpm
BAR
79,2
39,6
0
0 50 100 150 200
1501200 rpm
1500 rpm
1800 rpm
2200 rpm
100 26,4
13,2
81
27
200
200
60
52,880
90
108
54
250 66
10
30
50
70
1200 rpm 1500 rpm 1800 rpm
max speed / intake pipe pressure%
co
rrec
tio
n f
acto
r fo
rth
e m
ax s
pee
d
120%
115%
110%
105%
100%
95%
90%
-2,9 -1,45 0
PSI
1,45 2,9 4,35
-0,2 -0,1 0 0,1 0,2 0,3Intake pipe pressure (BAR)
0,4
5,8
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
BV52double pump
73
Shaft end cartridge V05-50
0 100 150 200
input torque / pressure
0 725 1450 2175 2900
PSI
600
0
NM
BAR50
400
power / pressure
KW
0
20
40
BAR
PSI
0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
162,6
0
HP
0 50 100 150 200
120
flow / pressurePSI
l/min
GP
M
350
50
0
0 725 1450 2175 2900
1000 rpm
600 rpm
BAR
92,4
39,6
0
0 50 100 150 200
150
1200 rpm
1500 rpm
1800 rpm
2200 rpm
100 26,4
13,2
81,3
27,1
200
200
60
52,880 108,4
54,2
250 66
300 79,2
100 135,5
Shaft end cartridge V05-47flow / pressure
PSI
l/min G
PM
100
0
0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200
50 13,2
BAR
150
26,4
KW
0
BAR
PSI0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
81,3
0
HP
0 50 100 150 200
power / pressure
40
120
54,2
27,1
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200
input torque / pressure
0 725 1450 2175 2900
PSI
0
NM
50
400
600
BAR
39,6
20
200
350
52,8
92,4
135,5
200
60
100250 66
80 108,4
300 79,2162,6
74
BV52double pump
Shaft end cartridge V05-57flow / pressure
PSI
l/min G
PM
100
0
0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm
1200 rpm1000 rpm
600 rpm
0
0 50 100 150 200
50 13,2
BAR
150
26,4
KW
0
BAR
PSI0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
68
0
HP
0 50 100 150 200
power / pressure
25
125
34
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200
input torque / pressure
0 725 1450 2175 2900PSI
0
NM
50
400
600
BAR
39,6
200
400
52,8
105,6
136
200
50
100
250 66
75 102
300 79,2
170350 92,4
Shaft end cartridge V05-60
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200
input torque / pressure
0 725 1450 2175 2900
PSI
0
NM
BAR50
400
power / pressure
KW
0
20
40
BAR
PSI0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
81,6
0
HP
0 50 100 150 200
140
flow / pressurePSI
l/min
GP
M
50
0
0 725 1450 2175 2900
1000 rpm
600 rpm
BAR
118,8
52,8
26,4
0
0 50 100 150 200
200 1200 rpm
1500 rpm
1800 rpm
2200 rpm
100
13,2
54,4
27,2
450
60
190,4
600
150 39,6
80
200
250 66
100
120 163,2
136
108,8
300
400 105,6
92,4
79,2
350
BV52double pump
75
Cover end cartridge V02-12
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
200
100500
NM
BAR50
150
power / pressure
KW
0
5
10
15
20
25
30
BAR
PSI0 725 1450 2175 2900 3625
1800 rpm
1500 rpm1200 rpm
1000 rpm
600 rpm
54,4
40,8
27,2
13,6
0
HP
0 50 100 150 200 250
35
40
flow / pressurePSI
l/min
GP
M
100
80
40
30
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
26
20,8
15,6
0
0 50 100 150 200 250
5,2
90
70
60
50
20
1200 rpm
1500 rpm
1800 rpm
2500 rpm
10
10,4
2500 rpm
Cover end cartridge V02-14flow / pressure
PSI
l/min G
PM
100
20
0
0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200 250
80
10,4
60
40
20,8
BAR
120
26
5,2
KW
0
5
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
600 rpm
54,4
0
HP
0 50 100 150 200 250
power / pressure
10
15
40
50
40,8
27,2
13,6
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
100
0
NM
50
150200
BAR
31,2
15,6
68
45
30
25
35
20
50
1000 rpm
double pump
76
BV52
Cover end cartridge V02-17
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
250
150
500
NM
BAR50
200
power / pressure
KW
0
10
20
40
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
81,6
68
40,8
13,6
0
HP
0 50 100 150 200 250
50
60
flow / pressurePSI
l/min
GP
M
140
80
40
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
36,4
31,2
26
0
0 50 100 150 200 250
5,2
120
60
20
1200 rpm
1500 rpm
1800 rpm
2500 rpm
15,6
100
20,8
10,4
30
54,4
27,2
100
Cover end cartridge V02-19flow / pressure
PSI
l/min G
PM
100
20
0
0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200 250
80
10,4
60
40
20,8
BAR
120
26
5,2
KW
0
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
54,4
0
HP
0 50 100 150 200 250
power / pressure
10
40
60
40,8
27,2
13,6
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
100
0
NM
50
200250
BAR
31,2
15,6
81,6
30
20
50
140
160
36,4
41,6
50 68
150
BV52
77
Installation dimensions mm (inches)
Approx. weight: 46 Kg. (101 lbs.)
double pump
Cover end cartridge V02-21
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
0
NM
BAR50
200
flow / pressurePSI
l/min
GP
M
140
80
40
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
42
31,5
21
0
0 50 100 150 200 250
120
60
20
1200 rpm
1500 rpm
1800 rpm
2500 rpm
100
10,5
100
160
180
300
power / pressure
KW
0
10
20
40
BAR
PSI
0 725 1450 2175 2900 3625
2500 rpm
1800 rpm1500 rpm
1200 rpm
1000 rpm
600 rpm
81,6
68
40,8
13,6
0
HP
0 50 100 150 200 250
50
70
30
54,4
27,2
60
95,2
78
BV52double pump
Cartridge types-shaft end 42 47 50 57 60
-cover end 12 14 17 19 21
Spline data(shaft 11 and shaft 90)
Spline Involute side fit (ASA B5.15)Pressure angle 30°No. of teeth 14Pitch 12/24Major dia. 31.60 - 31.50 (1.244 - 1.240)Pitch dia. 29.634 (1.1667)Minor dia. 26.99 - 26.66 (1.0627 - 1.05)Wildhaber 15.68 - 15.73 (0.617 - 0.619)
Shaft options mm (inches)
PORT ORIENTATIONS
Shaft01
Shaft11
Shaft90
Shaft86
Model code breakdown
BV 52 G * * * * * * * * (L) * (A)
Rotation(viewed from shaft end)L = left hand rotaton CCW (omit if CW)
Pump type
Body outlet port positions(outlet viewed from cover end)A = Outlet opposite endB = Outlet 90° CCW from inletC = Outlet in line with inletD = Outlet 90° CW from inlet
Mounting(omit if not required)Pump series Design
Seals(omit with standard seals andone shaft-seal in NBR)V = seals and shaft-seal in FPM (Viton®)D = standard seals and double shaft-seals in NBRF = seals and double shaft-seals in FPM (Viton®)
Shaft end options01 = Straight with key (standard), 11 = Splined86 = Heavy duty straight keyed, 90 = Splined SAE C
Cover outlet port positions(outlet viewed from cover end)A = Outlet 135° CCW from inletB = Outlet 45° CCW from inletC = Outlet 45° CW from inletD = Outlet 135° CW from inlet
79
BV52double pumpId
. cod
es o
f pum
p co
mpo
nent
s
Par
t N
o.
M80
5029
0
See
ger
Par
t N
o.
M80
5025
0
Bo
dy
Car
trid
ges
Ser
ies
V02
V02
Mo
del
12 14 17 19 21 12 14 17 19 21
Par
t N
o.
V02
1201
0V
0214
050
V02
1709
0V
0219
130
V02
2117
0V
0212
020
V02
1406
0V
0217
100
V02
1914
0V
0221
180
Ser
ies
V05
V05
Mo
del
42 47 50 57 60 42 47 50 57 60
Par
t N
o.
V05
4201
0V
0547
030
V05
5005
0V
0557
070
V05
6009
0V
0542
020
V05
4704
0V
0550
060
V05
5708
0V
0560
100
Pu
mp
ro
tati
on
right
han
d
left
hand
cove
r en
dsh
aft e
ndM
od
el01 11 86 90
Sh
aft
kit
Par
t N
o.
M85
2060
1M
8520
611
M85
2068
6M
8520
690
Mo
del
01 11 86 90
Sh
aft
Key
Par
t N
o.
K52
0100
0K
5211
000
K52
8600
0K
5290
000
Par
t N
o.
M80
5010
0-
M80
5860
0- P
art
No
.M
8050
300
M80
5030
5M
8050
301
M80
5030
6Sh
aft
seal Ty
pe
prim
ary
in N
BR
prim
ary
in F
PM
seco
ndar
y in
NB
Rse
cond
ary
in F
PM
Par
t N
o.
M80
4023
0To
rque
to 1
02 N
m (
910
lb. i
n.)
Scr
ewP
art
No
. M
8050
330
Torq
ue to
398
Nm
(35
50 lb
. in.
)
Scr
ew
Par
t N
o.
M80
5028
0
See
ger
Pu
mp
sea
l kit
Typ
eN
BR
NB
RF
PM
(V
iton®
)F
PM
(V
iton®
)
Par
t N
o.
M85
2050
0M
8520
501
M85
2050
3M
8520
504
Par
tsse
als
+ 1
sha
ft se
alse
als
+ 2
sha
ft se
als
seal
s +
1 s
haft
seal
seal
s +
2 s
haft
seal
s
Par
t N
o.
M80
5027
0
Bea
rin
g
Par
t N
o.
M80
5035
0
Cov
er
Par
t N
o.
M80
5040
0
Inle
t bod
y
80
BV54double pump
Fixed displacement vane pump,hydraulically balanced, with capacitydetermined by the cartridges used andthe speed of rotation. The pump isavailable in several versions with ratedcapacities from 244 to 370 l/min(from 63 to 98 gpm) at 1200 rpm and 7 bar.
General description
Hydraulic fluids: antiwear high quality mineral oils or fire resistant fluid having same lubricationcapacities of the mineral oil.
Viscosity range (with mineral oil): from 13 to 860 cSt. (13 to 54 cSt. recommended).
Filtration: for the inlet - 149 micron abs., for the return line - 25 micron abs. or better (with syntheticfluids: for the return line - 10 micron abs. or better).
Inlet pressure: (with mineral oil): from -0,17 to +1,4 bar (-2.5 to + 20 psi)
Operating temperature: with mineral oil -10°C +70°C (+30°C to +60°C recommended), with water
based fluids +15°C to +50°C.
Drive: direct and coaxial by means of a flexible coupling.
Technical characteristcs
Cartridgemodel
Geometricdisplacement
Ratedcapacity
Ratedcapacity
Maximumpressure
Speedrangerpmat 1200 rpm 7 bar at 1500 rpm 7 bar with mineral oil
cover end
V04-21
V04-25
V04-30
V04-35
V04-38
cm3/g
69,0
81,6
97,7
112,7
121,6
(in3/r)
(4.2)
(5)
(6)
(6.9)
(7.4)
l/min
79,5
94,0
113,8
131,6
139,9
(gpm)
(21)
(25)
(30)
(35)
(38)
l/min
101,4
120,1
141,2
167,2
177,3
(gpm)
(26.8)
(31.7)
(37.3)
(44.1)
(46.8)
bar
175
175
175
175
175
min
600
600
600
600
600
max
1800
1800
1800
1800
1800
(psi)
(2538)
(2538)
(2538)
(2538)
(2538)
shaft end
V05-42
V05-47
V05-50
V05-57
V05-60
cm3/g
138,6
153,5
162,2
183,4
193,4
(in3/r)
(8.46)
(9.4)
(9.9)
(11.2)
(11.8)
l/min
164
180
189
217
230
(gpm)
(42)
(47)
(50)
(57)
(60)
l/min
203,4
222,7
234
267
285
(gpm)
(53.7)
(58.8)
(61.8)
(71.2)
(75.3)
bar
175
175
175
175
175
min
600
600
600
600
600
max
1800
1800
1800
1800
1800
(psi)
(2538)
(2538)
(2538)
(2538)
(2538)
BV54double pump
81
If the intake pressure is not zero bar, use the graph below to find thepercentage correction factor to apply to the maximum speed
Main operating data
max pressure / hydraulic fluid
Antiwear industrialhydraulic oil
Syntetic fireresistant fluid
Waterglycol
max pres. peak pres. (0,5 sec.max)
Water-in-oilemulsion
250
200
150
100
50
0
BA
R
3625
2900
2175
PS
I
1450
725
0
2000
1600
1200
800600400
0
RP
M
Antiwear industrialhydraulic oil
Syntetic fireresistant fluid
Waterglycol
Water-in-oilemulsion
1800
1400
200
1000
max speed / hydraulic fluid (with 0 bar in the intake pipe)
speed
67
69
73
75
dB
(A)
Sound level at 138 bar (2000 psi)
71
Shaft end cartridge V05-42
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200
input torque / pressure
0 725 1450 2175 2900
PSI
600
0
NM
BAR50
400
power / pressure
KW
0
20
40
BAR
PSI0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
135
0
HP
0 50 100 150 200
100
flow / pressurePSI
l/min
GP
M
300
50
0
0 725 1450 2175 2900
1000 rpm
600 rpm
BAR
79,2
39,6
0
0 50 100 150 200
1501200 rpm
1500 rpm
1800 rpm
2200 rpm
100 26,4
13,2
81
27
200
200
60
52,880
90
108
54
250 66
10
30
50
70
1200 rpm 1500 rpm 1800 rpm
max speed / intake pipe pressure%
co
rrec
tio
n f
acto
r fo
rth
e m
ax s
pee
d
120%
115%
110%
105%
100%
95%
90%
-2,9 -1,45 0
PSI
1,45 2,9 4,35
-0,2 -0,1 0 0,1 0,2 0,3Intake pipe pressure (BAR)
0,4
5,8
82
BV54double pump
Shaft end cartridge V05-47flow / pressure
PSI
l/min G
PM
100
0
0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200
50 13,2
BAR
150
26,4
KW
0
BAR
PSI0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
81,3
0
HP
0 50 100 150 200
power / pressure
40
120
54,2
27,1
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200
input torque / pressure
0 725 1450 2175 2900
PSI
0
NM
50
400
600
BAR
39,6
20
200
350
52,8
92,4
135,5
200
60
100250 66
80 108,4
300 79,2162,6
Shaft end cartridge V05-50
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200
input torque / pressure
0 725 1450 2175 2900
PSI
600
0
NM
BAR50
400
power / pressure
KW
0
20
40
BAR
PSI0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
162,6
0
HP
0 50 100 150 200
120
flow / pressurePSI
l/min
GP
M
350
50
0
0 725 1450 2175 2900
1000 rpm
600 rpm
BAR
92,4
39,6
0
0 50 100 150 200
150
1200 rpm
1500 rpm
1800 rpm
2200 rpm
100 26,4
13,2
81,3
27,1
200
200
60
52,880 108,4
54,2
250 66
300 79,2
100 135,5
BV54double pump
83
Shaft end cartridge V05-57flow / pressure
PSI
l/min G
PM
100
0
0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm
1200 rpm1000 rpm
600 rpm
0
0 50 100 150 200
50 13,2
BAR
150
26,4
KW
0
BAR
PSI
0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
68
0
HP
0 50 100 150 200
power / pressure
25
125
34
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200
input torque / pressure
0 725 1450 2175 2900
PSI
0
NM
50
400
600
BAR
39,6
200
400
52,8
105,6
136
200
50
100
250 66
75 102
300 79,2
170350 92,4
Shaft end cartridge V05-60
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200
input torque / pressure
0 725 1450 2175 2900
PSI
0
NM
BAR50
400
power / pressure
KW
0
20
40
BAR
PSI0 725 1450 2175 2900
2200 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
81,6
0
HP
0 50 100 150 200
140
flow / pressurePSI
l/min
GP
M
50
0
0 725 1450 2175 2900
1000 rpm
600 rpm
BAR
118,8
52,8
26,4
0
0 50 100 150 200
200 1200 rpm
1500 rpm
1800 rpm
2200 rpm
100
13,2
54,4
27,2
450
60
190,4
600
150 39,6
80
200
250 66
100
120 163,2
136
108,8
300
400 105,6
92,4
79,2
350
84
BV54double pump
Cover end cartridge V04-21
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
300
0
NM
BAR50
200
power / pressure
KW
0
10
20
40
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm1500 rpm
1200 rpm
1000 rpm
600 rpm
108,8
81,6
0
HP
0 50 100 150 200 250
50
80
flow / pressurePSI
l/min
GP
M
180
80
40
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
42
31,5
0
0 50 100 150 200 250
120
60
20
1200 rpm
1500 rpm
1800 rpm
2500 rpm
100
21
10,5
30
54,4
27,2
100
140
160
70
60
Cover end cartridge V04-25flow / pressure
PSI
l/min G
PM
100
0
0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200 250
50 13,2
BAR
150
26,4
KW
0
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm1500 rpm1200 rpm1000 rpm
600 rpm
81,6
0
HP
0 50 100 150 200 250
power / pressure
10
40
90
54,4
27,2
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
1000
NM
50
300400
BAR
39,6
30
20
200
250
52,8
66
50
108,8
200
60
80
70
BV54double pump
85
Cover end cartridge V04-30
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
600
0
NM
BAR50
400
power / pressure
KW
0
20
40
BAR
PSI0 725 1450 2175 2900 3625
2500 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
136
0
HP
0 50 100 150 200 250
120
flow / pressurePSI
l/min
GP
M
250
50
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
66
39,6
0
0 50 100 150 200 250
150
1200 rpm
1500 rpm
1800 rpm
2500 rpm
100 26,4
13,2
81,6
27,2
200
200
60
52,8
80
100
108,8
54,4
Cover end cartridge V04-35flow / pressure
PSI
l/min G
PM
100
0
0 725 1450 2175 2900 3625
2400 rpm
1800 rpm
1500 rpm
1200 rpm
1000 rpm
600 rpm
0
0 50 100 150 200 250
50
13,2
BAR
150
26,4
KW
0
BAR
PSI0 725 1450 2175 2900 3625
2400 rpm
1800 rpm
1500 rpm1200 rpm
1000 rpm
600 rpm
81,6
0
HP
0 50 100 150 200 250
power / pressure
40
120
54,4
27,2
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
0
NM
50
400
600
BAR
39,6
20
200
300
52,8
79,2
136
200
60
100
250 66
80 108,8
86
BV54double pump
Installation dimensions mm (inches)
Approx. weight: 54 Kg. (118 lbs.)
Cover end cartridge V04-38
Oil viscosity: 25 c.St.(10W)Temperature: 45°CInlet pressure: 0 BAR
0 100 150 200 250
input torque / pressure
0 725 1450 2175 2900 3625PSI
0
NM
BAR50
400
power / pressure
KW
0
20
40
BAR
PSI0 725 1450 2175 2900 3625
2400 rpm
1800 rpm
1500 rpm1200 rpm
1000 rpm
600 rpm
81,6
0
HP
0 50 100 150 200 250
140
flow / pressurePSI
l/min
GP
M
50
0
0 725 1450 2175 2900 3625
1000 rpm
600 rpm
BAR
79,2
52,8
26,4
0
0 50 100 150 200 250
200
1200 rpm
1500 rpm
1800 rpm
2400 rpm
100
13,2
54,4
27,2
300
60
190,4
600
150 39,6 80
200
250 66
100
120 163,2
136
108,8
BV54double pump
87
Cartridge types-shaft end 42 47 50 57 60
-cover end 21 25 30 35 38
Spline data(shaft 11 and shaft 90)
Spline Involute side fit (ASA B5.15)Pressure angle 30°No. of teeth 14Pitch 12/24Major dia. 31.60 - 31.50 (1.244 - 1.240)Pitch dia. 29.634 (1.1667)Minor dia. 26.99 - 26.66 (1.0627 - 1.05)Wildhaber 15.68 - 15.73 (0.617 - 0.619)
Shaft options mm (inches)
PORT ORIENTATIONS
Shaft01
Shaft11
Shaft90
Shaft86
Model code breakdown
BV 54 G * * * * * * * * (L) * (A)
Rotation(viewed from shaft end)L = left hand rotaton CCW (omit if CW)
Pump type
Body outlet port positions(outlet viewed from cover end)A = Outlet opposite endB = Outlet 90° CCW from inletC = Outlet in line with inletD = Outlet 90° CW from inlet
Mounting(omit if not required)Pump series Design
Seals(omit with standard seals andone shaft-seal in NBR)V = seals and shaft-seal in FPM (Viton®)D = standard seals and double shaft-seals in NBRF = seals and double shaft-seals in FPM (Viton®)
Shaft end options01 = Straight with key (standard), 11 = Splined86 = Heavy duty straight keyed, 90 = Splined SAE C
Cover outlet port positions(outlet viewed from cover end)A = Outlet opposite endB = Outlet 90° CCW from inletC = Outlet in line with inletD = Outlet 90° CW from inlet
88
BV54double pump
Par
t N
o.
M80
5025
0
Bo
dy
Par
t N
o.
M80
5027
0
Bea
rin
g
Par
t N
o.
M80
5029
0
See
ger
Par
t N
o.
M80
5030
0M
8050
305
M80
5030
1M
8050
306Sh
aft
seal Ty
pe
prim
ary
in N
BR
prim
ary
in F
PM
seco
ndar
y in
NB
Rse
cond
ary
in F
PM
Pu
mp
sea
l kit
Typ
eN
BR
NB
RF
PM
(V
iton®
)F
PM
(V
iton®
)
Par
t N
o.
M85
4050
0M
8540
501
M85
4050
3M
8540
504
Par
tsse
als
+ 1
sha
ft se
alse
als
+ 2
sha
ft se
als
seal
s +
1 s
haft
seal
seal
s +
2 s
haft
seal
s
Car
trid
ges
Ser
ies
V04
V04
Mo
del
21 25 30 35 38 21 25 30 35 38
Par
t N
o.
V04
2101
0V
0425
050
V04
3009
0V
0435
130
V04
3817
0V
0421
020
V04
2506
0V
0430
100
V04
3514
0V
0438
180
Mo
del
01 11 86 90
Sh
aft
kit
Par
t N
o.
M85
4060
1M
8540
611
M85
4068
6M
8540
690
Mo
del
01 11 86 90
Sh
aft
Key
Par
t N
o.
K54
0100
0K
5411
000
K54
8600
0K
5490
000
Par
t N
o.
M80
5010
0-
M80
5860
0-
Ser
ies
V05
V05
Mo
del
42 47 50 57 60 42 47 50 57 60
Par
t N
o.
V05
4201
0V
0547
030
V05
5005
0V
0557
070
V05
6009
0V
0542
020
V05
4704
0V
0550
060
V05
5708
0V
0560
100
Pu
mp
ro
tati
on
right
han
d
left
hand
cove
r en
dsh
aft e
nd
Par
t N
o.
M80
5041
0
Par
t N
o.
M80
5038
0To
rque
to 3
98 N
m (
3550
lb. i
n.)
Scr
ew
Par
t N
o.
M80
5036
0
Co
ver
Par
t N
o.
M80
5028
0
See
ger
Inle
t bod
y
90
BV
02L6
2092
00L6
2093
00L6
2091
00L7
2090
02
05L6
2092
00L6
2093
00L6
2091
00L7
2090
05
08L6
2092
00L6
2093
00L6
2091
00L7
2090
08
V01
09L6
2092
00L6
2093
00L6
2091
00L7
2090
09L6
2001
00L6
2011
00L6
2006
00
11L6
2009
00L6
2008
00L6
2002
00L6
2003
00L6
2012
00L7
2010
11L6
2021
00 (
FP
M)
123,
6 N
mL6
2002
00L6
2003
00L6
2012
00L7
2010
12
14(3
2 lb
. in.
)L6
2002
00L6
2003
00L6
2012
00L7
2010
14
12L6
2510
12
14L6
2510
14
V02
17L6
2509
00L6
2508
00L6
2502
00L6
2503
00L6
2512
00L6
2510
17L6
2501
00L6
2511
00L7
2506
00
195,
5 N
mL6
2510
19L6
2521
00 (
FP
M)
21(4
9 lb
. in.
)L6
2510
21
21
L635
1021
25L6
3510
25
V04
30L6
3509
00L6
3508
00L6
3502
00L6
3503
00L6
3512
00L6
3510
30L6
3501
00L6
3511
00L7
3506
00
3512
,6 N
mL6
3510
35L6
3521
00 (
FP
M)
38(1
12 lb
.in)
L635
1038
42L6
4510
42
47L6
4510
47
V05
50L6
4509
00L6
4508
00L6
4502
00L6
4503
00L6
4512
00L6
4510
50L6
4501
00L6
4511
00L7
4506
00
5712
,6 N
mL6
4510
57L6
4521
00 (
FP
M)
60(1
12 lb
.in)
L645
1060
( *
) N
ote:
The
cov
er e
nd c
artr
idge
of t
he d
oubl
e pu
mp
is w
ithou
t bus
hing
.
12
34
56
78
9
Car
trid
ge
Scr
ew
Ser
ies
Mo
del
Pin
Inle
tsu
pp
ort
pla
te
Ro
tor
Van
e an
din
sert
kit
(12+
12 p
cs.)
Rin
gO
utl
etsu
pp
ort
pla
te
Sea
l kit
(4 p
cs.)
Bu
shin
g(
* )
91© 2008 B&C
Maximum speed: the maximum speeds given in this catalogue are valid for an atmospheric pressure of 1 bar (14.7 psi)and with ambient temperature in the range of +30°C to +50°C. Higher speeds than those given cause a reduction in thevolumetric efficiency, due to cavitation phenomena in the inlet area inside the pump. Sustained excess speed causes arapid deterioration of the internal components reducing the lifetime of the cartridge.
Minimum speed: In general, the min. speed for all pumps is 600 rpm. However, it is possible to operate at lower speedswith certain pump configurations and with appropriate operating temperatures.
Inlet pressure: the inlet pressure, measured at the inlet port, should remain within the prescribed limits. Note that pressureslower than minimum limit cause cavitation and pressures above the maximum limit cause abnormal loads on the shaftand the bearings. In both cases this causes a significant reduction in the lifetime of the cartridge.
Maximum outlet pressure: the maximum outlet pressure is different for each type of fluid used as can be seen from thecorresponding diagrams. With optimal temperature and filtration conditions a pressure peak of +10% is permissible for amaximum time of 0.5 sec.
Mounting and drive connections: consider the following indications when preparing the installation drawings for thesystem:• the pump is designed to operate with keyed shaft coupled axially and by means of a flexible coupling to the drive;• the clearance between the keyed shaft and the corresponding sleeve coupling has to be between 0.004 and 0.030 mm;• avoid axial and radial loads on the shaft;• the mounting flange has to be perpendicular to the drive shaft, with a maximum error of 0.18 mm every 100 mm;• when mounting onto a gearbox, or other component without a flexible coupling, it is advisable to order pumps with splined
shaft. In this case the clearance between splines has to be between 0.013 and 0.051 mm on the pitch diameter.
Hydraulic circuit: always install a pressure relief valve on the supply line to prevent the pressure from exceeding theallowed maximum. Normally, it is set in accordance with the weakest component in the system. (In the case where it isthe pump, set the valve to a pressure 15% higher than the maximum pressure rating of the pump.)Inlet line tubing should have a section equal to or greater than that of the inlet port of the pump. It is advisable to keepthe tube connecting the pump to the reservoir as short possible. Particular care has to be taken with the inlet line whichhas to be hermetically sealed to avoid entraining air into the circuit; this varies the characteristics of the hydraulic fluidcausing the operating parts to become damaged.
Filtration: the inlet line filter must have a flow rate capacity that is higher than that of the pump at its maximum operatingspeed. The filtration requirements for individual models are given in this catalogue. The use of a filter by-pass is recommendedfor cold starts and should the filter become clogged. Proper maintenance of the filter element is essential for the correctoperation of the entire system. In normal conditions replace the filter element after the first 50 hours of operation.Subsequently, replace it at least every 500 hours. Regarding the filter on the return line, the same general conditions applyas for the inlet line and it should be positioned in an accessible location for ease of maintenance.
Tank: if possible, the reservoir should be positioned above the pump. Otherwise, ensure that the minimum level of thefluid contained in it is higher than the pump inlet line opening. It is important to avoid draining the inlet line with the pumpat standstill. The opening of the return line into the reservoir must remain below the minimum level of the fluid in thereservoir. It must not be positioned too close to the opening of the inlet line to avoid the possibility of any air bubblespassing into the inlet line. Baffles inside the reservoir may be useful in avoiding the problem. Rapid temperature changescan cause condensation on the underside of the lid of the reservoir with the formation of droplets of water that can fallinto the oil. To avoid this problem it is recommended that the lid should have small vents so that the air space in thereservoir is ventilated. The vents have to be screened, though, to prevent the entry of dust or the sudden expulsion offluid.
Start-up: use the following procedure when the pump is started-up for the first time:completely fill the pump and the inlet line with fluid;start the engine for approximately one second a number of times at regular intervals of approximately 2 or 3 seconds untilthe noise level reduces, thereby confirming that it has been primed;with a manometer check to ensure that the outlet pressure increases slightly;once the pump has been primed, maintain low pressure levels activating all parts of the circuit a number of times untilair bubbles disappear completely from the return line to the reservoir.This procedure should be carefully as any residual air inside the pump can quickly cause the rotor to seize.
Cold starting: when starting the pump, especially with low ambient temperatures, operate with moderate speed andpressure until the average temperature in the entire circuit is within the given limits.
The information provided in this catalogue is subject to change without notice
Operating instructions
BV
28 Trowers Way Holmethorpe industrial estateredhill Surrey rH1 2LW. United Kingdom of Great Britain
telephone: +44(0)1737 767493 fax: +44(0)1737 772041 email: [email protected] website: www.jbj.co.uk