bul 1494c cable operated 200a disconnect...

Product Information

Bulletin 1494C Cable Operated 200A Disconnect Switch(For use with Cat 1494F-D200; 1494F-DX200 - Series D)

Additional Resources:1) Go to http://www.literature.rockwellautomation.com 2) Go to Search. Type in publication number: 42052-123-01

Disconnect Switch Installation (Right hand installation shown. For left hand installation follow similar procedure.)1

Enclosure with Right Hand Flange

Locate switch with right hand mechanism.1

1 2

Assemble disconnect switch to cable switch

mechanism.

Assemble disconnect switch assembly to

mounting plate.2 3

NOTE: For switch with left hand mechanism or

enclosure with left hand flange, reference

installation instruction sheet 42052-123-01

Disconnect Handle Installation2

Install gasket. Install handle and spring bracket. Install defeater lever.3

30 - 40 lb-in

7 - 11 lb-in

(Right HandFlange MountedShown)

8-1/4"

2"

1-1/8"

4-1/4"

7/32"

Dia.

16" Minimum

Disconnect Switch with

Right Hand Cable Mechanism

(shown)

40 - 60 lb-in

40 - 60 lb-in Thread forming

(TAP-TITE) screws

provided with cable

mechanism.

Thread forming

(TAP-TITE) screws

provided with

disconnect switch.

ATTENTION: Do not install, configure, operate or maintain this product until you have read the product documentation and the documents in the Additional Resources section for installing, configuring, operating or maintaining

equipment. To get the product documentation go to http://www.literature.rockwellautomation.com or contact your local sales office or Rockwell Automation representative.

ATTENTION: Ne pas installer, configurer, exploiter ou maintenir ce produit tant que vous n’avez pas lu sa documentation et les documents de la rubrique Documents connexes pour l’installation, la configuration, l’exploitation et la

maintenance de l’équipement. Pour obtenir de la documentation, rendez-vous sur le site http://www.literature.rockwellautomation.com ou contactez votre agence commerciale Rockwell Automation locale ou son représentant.

ACHTUNG: Für die Installation, Konfiguration, den Betrieb und die Wartung dieses Produkt lesen Sie sich bitte zunächst die Produktdokumentation sowie die Dokumente im Abschnitt „Weitere Informationen“ durch. Die

entsprechende Produktdokumentation finden Sie unter http://www.literature.rockwellautomation.com oder kontaktieren Sie Ihr lokales Vertriebsbüro bzw. einen Rockwell Automation-Mitarbeiter.

ATENCIÓN: No instale, configure, opere ni mantenga este producto hasta que haya leído la documentación del producto y los documentos en la sección Recursos adicionales para la instalación, configuración, operación o

mantenimiento de equipo. Para conseguir la documentación, diríjase a http://www.literature.rockwellautomation.com o póngase en contacto con su oficina regional de ventas o representante de Rockwell Automation.

ATENÇÃO: Não instale, configure, opere ou mantenha este produto até que você leia a documentação do produto e os documentos na seção Recursos adicionais para a instalação, configuração, operação ou manutenção do

equipamento. Para conseguir a documentação, visite http://www.literature.rockwellautomation.com ou entre em contato con seu escritório de vendas regional ou representante da Rockwell Automation.

ATTENZIONE: Non installare, configurare, attivare o riparare questo prodotto senza avere prima letto la relativa documentazione nonchè i documenti indicati nella sezione Ulteriori Risore riguardanti l’installazione, la configurazione,

l’attivazione o la riparazione dell’apparecchiatura. Per la documentazione sul prodotto visitare il sito http://www.literature.rockwellautomation.com o contattare l’ufficio vendite o il rappresentate Rockwell Automation di zona.

WARNING: To prevent electrical shock, disconnect from power source before installing or servicing. Follow NFPA 70E requirements. Install in suitable enclosure. Keep free from contaminants.

The following procedures are critical to the proper operation of the disconnect handle and switch. Failure to follow these steps can result in damage to the equipment and/or serious injury or death to the operator.

Installation, adjustments, putting into service, use, assembly, disassembly, and maintenance shall be carried out by suitably trained personnel in accordance with applicable code of practice. In case of malfunction or

damage, no attempts at repair should be made. The product should be returned to the manufacturer for repair. Do not dismantle the product.

http://www.literature.rockwellautomation.com



Primary Link

Cable Mechanism Installation3

1 2Rotate connecting rod (clockwise) into drive bar

until it bottoms out.Verify that disconnect switch and handle are in

"ON" position. (Switch blades will not be visible).

4 Align connecting rod with primary link. 5 Install hitch pin clip. 6 Turn disconnect handle "OFF" and

install handle mechanism spring.

Connecting

Rod

Rotate connecting rod (counter-clockwise)

3 full turns.3

ATTENTION: Check for proper operation. Upon successful completion of the

installation instructions no further adjustment of the cable mechanism is required.

Go to Installation Instruction Sheet 42052-123-01.

Trailer Fuse Block Installation4

Drive

Bar

PN-133646DIR 42052-152 (Version 03)

Copyright © 2013 Rockwell Automation, Inc. All Rights Reserved. Printed in USA.

Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

Publication 1494C-IN002C-EN-E - January 2013

TWO SIDES PRINTEDBODY STOCK LIGHT TAN-20# BOND

BODY INK BLACK

MATERIALNO.

MATERIALFOLD

SIZE

PN-133646 11" W x 8-1/2" H

FLAT

11" W x 17" H

Note: After folding---Printed in (Country where printed)*, instruction sheet SAP numbers and barcodeshould be visible.

* The printing vendor may change the instruction sheet files to show the correct country.

Final Fold

Page Layout

17”11”

PN-133646DIR 42052-152 (Version xx)


8 - 1/2”11”

PN-133646DIR 42052-152 (Version xx)
