btr-800, tr-800
TRANSCRIPT
![Page 1: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/1.jpg)
TelexOp er ating In struc tions
RadioCom™
BTR-800, TR-800, TR-825
Pro fes sional Wire lessIn ter com Sys tem
0891
![Page 2: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/2.jpg)
Thank you for choos ing RadioComTM
Telex Com mu ni ca tions would like to take this op por tu nity to thank you for choos ing the RadioCom™ BTR-800
Pro fes sional Wire less In ter com Sys tem. Many of the fea tures in this prod uct are the re sult of years of de vel op --
ment work with many of the fea tures de vel oped from cus tomer feed back. We hope that your ex pe ri ence with this
prod uct is a pleas ant one and hope to pro vide you with a con tin u ing line of RadioCom™ prod ucts well into the
fu ture. In or der to get the most out of your new wire less in ter com sys tem, please take a few mo ments to look
through this book let be fore us ing the prod uct for the first time.
-Telex Com mu ni ca tions, Inc.
![Page 3: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/3.jpg)
Ta ble of Con tentsIn tro duc tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Gen eral De scrip tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1Sys tem Fea tures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1BTR-800 Block Di a gram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
BTR-800 Base Sta tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1Con trols and Con nec tions - Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1Con trols and Con nec tions - Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2BTR-800 Spec i fi ca tions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
TR-800 Beltpack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1Con trols and Con nec tions - Top Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1Con trols and Con nec tions - Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2TR-800 Spec i fi ca tions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
TR-825 Beltpack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1Con trols and Con nec tions - Top Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1Con trols and Con nec tions - Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2TR-825 Spec i fi ca tions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Ini tial Equip ment Set-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1Un packing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1An tenna Con nec tions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2An tenna Po lar iza tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2Dis tance Be tween An tennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2An tenna Place ment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2Im proving Re cep tion/In creasing Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4Base Sta tion Set-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Lo ca tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5Power Con nec tion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5Trans mit Switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5In ter nal Trans mit Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6In ter com Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6In ter com In ter face. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6Dual Lis ten Func tion al ity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8Aux il iary In put/Out put . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9In ter nal Aux il iary In put Routing Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9Stage An nounce /Re lay Con tacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10Base Sta tion Link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
Beltpack Set-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12Bat tery In stal la tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12An tenna Con nec tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13Trans mit Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13Head set Con nec tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
Pre-Walk-Thru Check list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Sys tem Op er a tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1Fre quency Plan Over view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1Fac tory-Defined Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1User-Programmable Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1Sys tem Quick Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1Base Sta tion Op er a tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2Lo cal Head set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2Por ta ble Sta tion Con nect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2In ter com A and B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2Aux il iary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2Dis play Con trast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3BTR-800 Menu Struc ture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
Main Screen Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4Power-Up Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5Op er ating Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5Beltpack Ac tiv ity Code Def i ni tions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5Group/Chan nel Se lect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6Group/Fre quency Se lect. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7Fre quency Edit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8Clear Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9Spe cial Key Se quences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10
Lock out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10Copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-101st Use De fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10Fac tory De fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10
-i-
![Page 4: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/4.jpg)
Ta ble of Con tents (con tin ued)TR-800 Beltpack Op er a tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11
Power/Lo cal Head set Vol ume. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11Bat tery Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11Talk But ton . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11Mi cro phone Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11Chan nel Se lect But ton . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11Stage An nounce (SA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11Wire less Talk Around (WTA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11TR-800 Beltpack Menu Struc ture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12
Power-Up Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-13Group/Chan nel Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14Trans mit Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-15Re ceive 1 Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-16Re ceive 2 Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-17ClearScan™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-18Fea ture En able/Dis able Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19Stage An nounce En able/Dis able . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19Wire less Talk Around En able/Dis able . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19Au dio Chan nel A or B En able/Dis able . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-20Talk But ton Latch on/Latch off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-20Spe cial Key Se quences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-21
Lock out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-211st Use De fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-21Fac tory De fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-21
TR-825 Beltpack Menu Struc ture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-22Power-Up Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-23Group/Chan nel Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-24Trans mit Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-25Re ceive 1 Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-26Re ceive 2 Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-27Au dio Out put . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-28ClearScan™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-29Fea ture En able/Dis able Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-30Stage An nounce En able/Dis able . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-30Wire less Talk Around . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-31Au dio Chan nel A Op tions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-32Au dio Chan nel B Op tions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-33Spe cial Key Se quences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-34
Lock out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-341st Use De fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-34Fac tory De fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-34
Sys tem Walk-Thru . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
Trou ble Shoot ing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
Tech Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1Fre quency In ter ac tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1Mi cro phone Gain Ad just ment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
Bat tery In for ma tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1
In ter com Sys tem Spec i fi ca tions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1
Ac ces sories and Re place ment Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1
Soft ware Li cense. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1
Certification In for ma tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-1
Dec la ra tion of Con for mity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-3
-ii-
![Page 5: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/5.jpg)
In tro duc tion
Gen eral De scrip tion
The Telex RadioCom™ BTR-800 UHF Syn the sized Wire lessin ter com sys tems of fer the ul t i mate in re l i ab le ,high-performance, high-fidelity full-duplex com mu ni ca tions.
The BTR-800 sys tem in cludes the BTR-800 fre quency ag ilebase sta tion, work ing with up to four TR-800 or TR-825 fre --quency ag ile beltpacks. The BTR-800 base sta tion pro videsfull-duplex com mu ni ca tions with the beltpacks.
The BTR sys tem in cor po rates two au dio chan nel op er a tion,per mit ting the beltpack op er a tor to choose be tween two sep a --rate au dio chan nels of com mu ni ca tions, with the base sta tiontrack ing the beltpack se lec tion. This al lows the user the flex i --bil ity to cre ate a party-line and a pri vate line within the samebeltpack.
The BTR-800 sys tem is per fectly suited for stand-alone op er a --tion and also can in ter face with Audiocom® (Telex), RTS®TW, Clear-Com®, as well as RTS Ma trix sys tems and other4-wire com mu ni ca tions sys tems. In ad di tion to the ex ter nal in --ter com sys tems in ter faces listed above, the sys tem pro videscon nec tions for aux il iary bal anced au dio in put and out put, aswell as wire less talk-around (WTA) and stage an nounce (SA)fea tures.
The RadioCom™ BTR se ries has been de signed for re li able,ef fi cient op er a tion. Op er ating in the 470 to 740 MHz range,the units op er ate re li ably at line-of-sight dis tances of 1,000feet. With avail able an tenna sys tems, from Telex, the ef fec tiveop er at ing range can be ex tended. The high-efficiencybeltpacks pro vide up to 12 hours of un in ter rupted op er a tionus ing stan dard al ka line bat ter ies.
Sys tem Fea tures
• Fre quency-agile base sta tion and beltpacks. No ex ter nalcom puter/de vice re quired to se lect fre quen cies.
• Backlit base-station LCD al lows the user to eas ily mon i -tor the beltpack’s sta tus as well as change base-station fre -quen cies.
• ClearScan™ func tion on base sta tion and beltpack to au -to mat i cally find the best chan nels on which to op er ate.
• Full-duplex (si mul ta neous talk and lis ten) op er a tion.
• Com pat i ble with Audiocom® (Telex), RTS TW, Ma trix,Clear-Com® , and other wired in ter com types.
• Two chan nels of in ter com au dio.
• WTA (Wire less Talk Around) beltpack con trol. This fea -ture al lows beltpacks to talk to each other, but their au diois lifted from any wired sys tem con nected to the base sta -tion.
• SA (Stage An nounce) beltpack con trol. Al lows the user to di rect their au dio to a jack on the back of the base for P.A. sys tems or other ex ter nal au dio sys tems.
• Re lay con tact clo sure on the base when the SA but ton ispressed.
• TR-825 fea tures two au dio chan nel bin au ral op er a tion inei ther ste reo or mono mode.
• Beltpack units con tained in a weather and shock re sis tantdie cast mag ne sium case.
• Con ve nient IEC power con nec tor on the base sta tion sothe unit can plug di rectly to out lets. No in-line or wallplug power sup ply.
• Base sta tion co mes with rack ears for easy rack mount ing.
1-1
RTS® and Audiocom® are reg is tered trade marks of Telex Com mu ni ca tions, Inc.Clear-Com® is a reg is tered trade mark of Clear-Com In ter com Sys tems, Inc.
Section
1
![Page 6: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/6.jpg)
1-2
PO
RTA
BL
ES
TAT
ION
1C
ON
NE
CT
RE
CE
IVE
1
LO
GIC
PO
RTA
BL
ES
TAT
ION
2C
ON
NE
CT
LO
GIC
1 O
F 5
RE
CE
IVE
2
PO
RTA
BL
ES
TAT
ION
3C
ON
NE
CT
LO
GIC
RE
CE
IVE
3
PO
RTA
BL
ES
TAT
ION
4C
ON
NE
CT
RE
CE
IVE
4
LO
GIC
LO
GIC
WTA
A
TR
AN
SM
IT 1
LO
GIC
SE
LE
CT
FE
MA
LE
MA
LE
XL
R
2 W I R E
4 W I R E
2 W
IRE
4 W
IRE
INT
ER
CO
M A
I/C
T E L E X
R T S
C L E A R C O M
CH
AN
NE
L B
AU
XIL
IAR
YA
UD
IOIN
PU
TX
LR
FE
MA
LE
ON
/OF
F
ON
/O.M
.IN
INT
ER
CO
M B
OU
T
2 W
IRE
4 W
IRE
RJ
11
ST
YL
E
2 W
IRE
INT
ER
CO
M A
OU
T
INT
ER
CO
M A
IN
INT
ER
CO
M B
IN
RJ1
1S
TY
LE
4 W
IRE
4 W
IRE
2 W
IRE
MA
LE
FE
MA
LE
XL
R
SE
LE
CT
LO
GIC
INT
ER
CO
M B
AU
XIL
IAR
YA
UD
IOO
UT
PU
T
XL
RM
AL
E
OU
T
TR
AN
SM
IT 2
WTA
B
SE
LE
CT
1 O
F 5
SE
LE
CT
1 O
F 5
SE
LE
CT
1 O
F 5
SE
LE
CT
SA
MIC
GA
IN
XL
R
HE
AD
SE
T
14
23
LO
GIC
CH
AN
NE
LS
EL
EC
T
CH
AN
NE
L A
TAL
K
TAL
K
AB
VO
LU
ME
LO
GIC
XL
RM
AL
ES
TA
GE
AN
NO
UN
CE
OU
TP
UT
RE
LA
YC
ON
TA
CT
mar
g ai
D kc
olB
00
8-R
TB
![Page 7: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/7.jpg)
BTR-800 Base Sta tionCon trols and Con nec tions - Front Panel
1. Power switch.
2. [Menu] and [Set] but tons – Used to se lect menus and setop tions on the LCD.
3. Backlit Graph ics LCD (Liq uid Crys tal Dis play).
4. [Up] and [Down] but tons – Used to se lect base sta tionop tions on the LCD.
5. Por ta ble Sta tion Con nect – But tons used to en able ordis able the re spec tive re ceiver’s au dio. GREEN LED =Au dio en abled, LED OFF = Au dio dis abled.
6. In ter com A Con trols - Wired in ter com A in ter face con -trols. Au dio in put and out put level con trols. 2-wire or4-wire se lect but ton with green LED in di ca tor lights. Se -lected LED will change to RED if the in put lev els are toohigh.
7. In ter com B Con trols - Wired in ter com B in ter face con -trols. Au dio in put and out put level con trols. 2-wire or4-wire se lect but ton with green LED in di ca tor lights. Se -lected LED will change to RED if the in put lev els are toohigh.
8. Aux il iary Con trols - Wired aux il iary in ter face con trols.Au dio in put and out put level con trols. GREEN LED =Aux. in put en abled. LED will change to RED if the in putlev els are too high.
9. Head set Vol ume – Con trols the vol ume to the head setcon nected to #14.
10. Head set In ter com Se lect – Con trols the in ter com towhich the lo cal head set is con nected. Each press of thebut ton changes the con nec tion; chan nel A, chan nel B,both.
11. Talk/Overmod Light – LED is green when talk but ton#13 is ac tive. A nor mal mic gain set ting will cause theLED to flash red on the loud est speech lev els. If the gainis too high, the LED will be red at nor mal speech vol umes.
12. Mi cro phone Gain – Ad justs the head set’s mi cro phonegain. Ad justs so that the overmod light #11 flashes fromgreen to red on loud est speech.
13. Talk But ton – Press to en able the au dio path from the lo cal head set. LED #11 will turn green when en abled. A quickpress and re lease latches but ton on. If the talk func tion islatched on, press ing the talk but ton again will turn it off.
14. Lo cal Head set Con nec tor – Male XLR con nec tor forTelex units, Fe male XLR con nec tor for RTS units. A dy -namic or electret head set mi cro phone is au to mat i cally de -tected.
Fig ure 2Lo cal Head set Wiring
2-1
TALK
MIC GAIN
TALK/O.M.VOLUME
SELECT
A
B
ON/O.M.
ON/OFF
IN
OUT
AUXILIARYINTERCOM B
2 WIRE
4 WIRE
SELECT
IN
OUT
2 WIRE
4 WIRE
SELECT
IN
OUT
INTERCOM APORTABLE STATION CONNECT
1 2 3 4
UP
DOWN
MENU
SET
RadioComä BTR-800
ClearScanTM
COPY
1 2 3 4 5 6 7 8 9 10
11
12
13 14Fig ure 1BTR-800 - Front Panel
(1) MicrophoneShield (-)
(2) MicrophoneAudio (+)
(3) HeadphoneHigh (+)
(4) HeadphoneLow (-)
Telex Units
(4) HeadphoneLow (-)
(3) HeadphoneHigh (+)
(1) MicrophoneShield (-)
(2) MicrophoneAudio (+)
PUSH
Section
2
(5) (4) HeadphoneLow (-)
(3) HeadphoneHigh (+)
(1) MicrophoneShield (-)
(2) MicrophoneAudio (+)
PUSH
RTS Units
![Page 8: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/8.jpg)
Con trols and Con nec tions - Rear Panel
1. Re ceive An tenna - Fe male “TNC” Con nec tor. Color band on an tenna must match color dot on base sta tion.
2. Trans mit Power Switch – HIGH = Trans mit ters at fullpower. NOR MAL = Trans mit ters 10dB be low full power.
3. Trans mit ON/OFF Switch – Turns the trans mit ters on or off.
4. I/C Se lect Switch – Set to the ap pro pri ate 2-wire in ter com type be ing in ter faced to the unit. Set to ei ther Telex, RTSor Clear-Com®.
5. Base Sta tion Link Jack – When two base sta tions arecon nected through this jack, it al lows wire less talk around(WTA) from the beltpacks to be routed from the sys temwith it’s trans mit ters off to the sys tem with it’s trans mit ters on.
6. Re lay Con tact – A dry con tact clo sure which is ac ti vatedwhen a beltpack user presses the stage an nounce (SA) but -ton. Normally Open (NO). One amp at 24V max i mum.
7. In ter com A – In ter face to wired in ter com sys tem A. 2-Wire – Male and fe male 3-pin XLR con nec torswired in par al lel. The con nec tors are switched to theap pro pri ate in ter com con fig u ra tion via the I/C Se lectSwitch.
4-Wire – An RJ-11 type jack com pat i ble with “Ma -trix” type in ter com sys tems.
8. In ter com B – In ter face to wired in ter com sys tem B. 2-Wire – Male and fe male 3-pin XLR con nec torswired in par al lel. The con nec tors are switched to theap pro pri ate in ter com con fig u ra tion via the I/C Se lectSwitch.
4-Wire – An RJ-11 type jack com pat i ble with “Ma -trix” type in ter com sys tems.
9. Aux il iary In put/Out put – One 3-pin fe male XLR in putcon nec tor and one 3-pin male XLR out put con nec tor.
10. Stage An nounce Out put – Passes the au dio from any ofthe base sta tion’s beltpacks that have se lected stage an -nounce (SA).
11. Power – IEC re cep ta cle. Ac cepts 100 – 240 VAC, 50 – 60 Hz.
12. Trans mit An tenna - Fe male “TNC” Con nec tor. Colorband on an tenna must match color dot on base sta tion.
2-2
RECEIVE
HIGH
ON
NORM
OFF
TRANSMITPOWER
I/C
TELEX CLEARCOMRTS
BTR-800FCC ID: B5DM514
CANADA 1321231218A
BASE STATIONLINK
RELAYCONTACT
INTERCOM A2 WIRE
LOOP
THRU
4 WIRE
INTERCOM B2 WIRE
LOOP
THRU
4 WIRE
AUXILIARY AUDIO
INPUT OUTPUT
STAGE ANNOUNCE
OUTPUT POWER
100-240 VAC 50-60 Hz
TRANSMIT
MADE IN USA
PUSHPUSHPUSH
TelexTelex Communications, Inc.
1
2 3 4 5 6 7 8 9 10 11
12
Fig ure 3BTR-800 - Rear Panel
Warn ing! Ex ces sive cur rent through the loop thru ports will dam age the in ter com! Do notex ceed 200 mA cur rent in the 2 wire loopthru curcuits.
Warn ing! Ex ces sive cur rent through the loop thru ports will dam age the in ter com! Do notex ceed 200 mA cur rent in the 2 wire loopthru curcuits.
![Page 9: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/9.jpg)
2-3
BTR-800Spec i fi ca tions
Over all
RF Fre quency Range . . . . . . . . . . . . . . . . . . . . . . 470 - 608 MHz, 614 - 740 MHz in 18 MHz TX and RX bands
Power Re quire ments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100-240 VAC, 50-60 Hz, IEC re cep ta cle
Tem per a ture Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -4° F to 130° F (-20° C to 55° C)
Di men sions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.00” W x 1.72” H x 14.00” D (48.3 cm x 4.4 cm x 35.6 cm)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 lbs 2 oz (3.24 kg)
TX An tenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2 Wave (sup plied), TNC Male Con nec tor
RX An tenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2 Wave (sup plied), TNC Male Con nec tor
FCC ID: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B5DM529 (TX 482-518 MHz) B5DM514 (TX 518-608 MHz)
Fre quency Re sponse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300Hz-8kHz
Four Wire In put . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Level Ad just able (2 Vrms typ i cal)
Four Wire Out put . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Level Ad just able (2 Vrms typ i cal)
Telex In ter com. . . . . . . . . . . . . . . . . . . . In put/Out put Level Ad just able (1 Vrms typ i cal), Line im ped ance 300W
RTS In ter com . . . . . . . . . . . . . . . . . In put/Out put Level Ad just able (0.775 Vrms typ i cal), Line Im ped ance 200W
Clear-Com® In ter com . . . . . . . . . . . . . In put/Out put Level Ad just able (1 Vrms typ i cal), Line Im ped ance 200W
Aux il iary In put . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ad just able (2 Vrms typ i cal)
Aux il iary Out put . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ad just able (2 Vrms typ i cal into 600W)
Stage An nounce Out put . . . . . . . . . . . . . . . . In ter nally Ad just able (2 Vrms typ i cal at rated de vi a tion into 600W)
Stage An nounce Re lay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dry con tact, rated at 1 Amp, 24V Max
Mi cro phone in put sen si tiv ity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9mV
Lo cal Head set Out put . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40mW out put into 600W (1% Dis tor tion)
Trans mit ter
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Two Syn the sized Trans mit ters, 712 chan nels each
Trans mit Power (each trans mit ter). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100mW Max. (High), 10 mW (Nor mal)
Mod u la tion Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FM
De vi a tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 kHz (35 kHz Eu rope)
RF Fre quency Sta bil ity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.005%
Mod u la tion Lim iter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Peak-Responding Com pres sor
Ra di ated Har monics & Spu ri ous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ex ceeds FCC spec i fi ca tions
Re ceiver
Type. . . . . . . . . . Dual Con ver sion Super het ero dyne, four In de pend ent Syn the sized IFs, FM, 712 chan nels each
RF Sen si tiv ity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <0.8 µV for 12 dB SINAD
Squelch Thresh old . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 dB SINAD
IF Se lec tiv ity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 dB at 230 kHz
Im age Re jec tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 dB or better
Squelch Quieting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 dB
RF Fre quency Sta bil ity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.005%
Dis tor tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <1% at full de vi a tion
![Page 10: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/10.jpg)
2-4 Blank
![Page 11: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/11.jpg)
TR-800 Beltpack Con trols and Con nec tions - Top Panel
Fig ure 4TR-800 Top Panel
1. On/Off & Vol ume Con trol – Turns the beltpack poweron and con trols head set vol ume.
2. Wire less Talk Around (WTA) – When pressed, the user’s au dio is dis con nected from the wired in ter com, aux il iaryin put/out put and the base sta tion’s lo cal head set. Otherbeltpack us ers, on that au dio chan nel, can hear the user asnor mal. The but ton ac ti vates the nearby red LED as wellas the “TALK” LED, #6, when pressed.
3. Stage An nounce (SA) –When pressed, the user’s au dio isrouted to the stage an nounce con nec tor on the back of thebase sta tion. The user also loses their sidetone as an in di -ca tion that stage an nounce is ac ti vated. The other wire lessbeltpacks and wired us ers do not hear the user’s au dio.The but ton is non-latching and ac tivates the nearby redLED as well as the “TALK” LED, #6, when pressed.
4. Au dio Chan nel Se lect Button – Al lows user to se lect ei -ther au dio chan nel A or B.
5. Bat/Overmod Light (BAT/OM) – Light will flash oncewhen unit is turned on if the bat tery is good. If the lightstays on, bat tery is low. If the light does not flash, bat teryis dead. A nor mal mi cro phone gain set ting will cause theLED to flash at the be gin ning of most words at nor malspeech lev els. If the gain is too high, the LED will be reddur ing the com plete word at nor mal speech lev els.
6. Talk Light – LED is on when the talk but ton, SA or WTAis ac tive.
7. Talk but ton – Press to en able the au dio path from the lo -cal head set mi cro phone. The “TALK” LED, #6, will turnred when en abled. A quick press and re lease latches thetalk func tion, un less latch ing has been dis abled. Holdingthe but ton for over ½ a sec ond will cause the au dio path to be en abled only for as long as the but ton is held. If the talk func tion is latched on, press ing the talk but ton again willturn it off.
3-1
VOL
OFFSA
WTA
Telex R
A B
CHANNEL
BAT/OM TALK
TALK
1 2 4 5 6
7
3
Section
3
![Page 12: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/12.jpg)
Con trols and Con nec tions - Rear Panel
Fig ure 5TR-800 Rear Panel/Con nec tor/An tennas
1. [MENU] and [SET] but tons – Used to se lect menus andset op tions on the LCD.
2. LCD (Liq uid Crys tal Dis play)
3. [UP] and [DOWN] but tons – Used to se lect beltpack op -tions on the LCD.
4. Mi cro phone Gain – Ad justs the head set’s mi cro phonegain. Ad just so that the BAT/OM LED will flash at the be -gin ning of most words at nor mal speech lev els
5. Push-to-Talk/Push-to-Transmit Switch – Push-to-Talk (PT TALK) – The trans mit ter is al wayson. No au dio sent un less the talk switch, WTA or SAbut ton pressed. Rec om mended po si tion.
Push-to-Transmit (PT TX) - The trans mit ter and au dio path are off ex cept when the talk switch, WTA or SAbut ton is pressed.
6. Head set Con nec tor – Male XLR con nec tor for Telexunits, Fe male XLR con nec tor for RTS units. A dy namic or electret head set mi cro phone is au to mat i cally de tected bythe beltpack and a bias volt age sup plied if needed.
Fig ure 6Head set Jack Wiring
7. Bat tery Latch – Press down to en able the bat tery pack tobe re leased. While the latch is held down, slide the bat tery pack about 1/8 inch back, to ward the latch, un til it stops.Then lift out.
8. Re ceive An tenna – Screw type ¼-wave re place able an -tenna. The color dot on the screw end of the an tenna mustmatch color dot on an tenna re cep ta cle.
9. Trans mit An tenna – Screw type ¼-wave re place able an -tenna. Color dot on the screw end of the an tenna mustmatch color dot on an tenna re cep ta cle.
3-2
(1) MicrophoneShield (-)
(2) MicrophoneAudio (+)
(4) HeadphoneLow (-)
(3) HeadphoneHigh (+)
(1) MicrophoneShield (-)
(4) HeadphoneLow (-)
(3) HeadphoneHigh (+)
(2) MicrophoneAudio (+)
RTS Units
Telex Units
ME
NU
SE
T
MIC PTTX
PTTALK
66
7788
99
ME
NU
SE
T
MIC PTTX
PTTALK
22
11
33
44
55
(1) MicrophoneShield (-)
(5) (4) Headphone Low (-)
(3) Headphone High (+)
(2) MicrophoneAudio (+)
![Page 13: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/13.jpg)
3-3
TR-800Spec i fi ca tions
RF Fre quency Range . . . . . . . . . . . . . . . . . . . . . . 470 - 608 MHz, 614 - 740 MHz in 18 MHz TX and RX bands
Power Re quire ments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 “AA” Cells Al ka line (NiMH op tional)
Cur rent Draw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 mA (Push-to-Talk, Talk On)
Tem per a ture Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -4° F to 130° F (-20° C to 55° C)
Di men sions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.75”W x 5.05”H x 1.65” D (9.5 cm x 12.8 cm x 4.2 cm)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 oz (454g) with al ka line bat ter ies
TX An tenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4 Wave (sup plied), Screw type, Re place able
RX An tenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4 Wave (sup plied), Screw type, Re place able
FCC ID: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B5DM518 (TX 470-608 MHz), B5DM515 (TX 614-746 MHz)
Fre quency Re sponse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300Hz-8kHz
Mi cro phone in put sen si tiv ity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 mV
Lo cal Head set Out put . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 mW out put into 600W (1% dis tor tion)
Trans mit ter
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Syn the sized, 712 chan nels
Trans mit Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mW Max. (auto-power re duc tion)
Mod u la tion Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FM
De vi a tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 kHz (35 kHz Europe)
RF Fre quency Sta bil ity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.005%
Mod u la tion Lim iter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Peak-Responding Com pres sor
Ra di ated Har monics & Spu ri ous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ex ceeds FCC spec i fi ca tions
Re ceiver
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dual Con ver sion Super het ero dyne, Syn the sized, FM, 712 chan nels
RF Sen si tiv ity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <0.7 µV for 12 dB SINAD
Squelch Thresh old . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 dB SINAD (About 1.0 µV)
IF Se lec tiv ity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 dB at 230 kHz
Im age Re jec tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 dB or better
Squelch Quieting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 dB
RF Fre quency Sta bil ity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.005%
Dis tor tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <1% at full de vi a tion
![Page 14: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/14.jpg)
3-4 Blank
![Page 15: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/15.jpg)
TR-825 Beltpack Con trols and Con nec tions - Top Panel
Fig ure 7TR-825 Top Panel
1. On/Off and Vol ume Con trol - Turns beltpack power onand con trols head set vol ume for In ter com Chan nels “A”and “B”. Ei ther knob, “A” or “B”, turns the beltpack on.Both knobs must be off to turn the beltpack off. If onlyone knob is off, then only that In ter com Chan nel, “A” or“B” is off for both trans mit and re ceive au dio.
2. Wire less Talk Around (WTA) - When pressed, the user’s au dio is dis con nected from the wired in ter com, aux il iaryin put/out put and the base sta tion’s lo cal head set. Otherbeltpack us ers, on that au dio chan nel, can hear the user asnor mal. The de fault set ting is soft ware selectable, as towhich In ter com Chan nel, “A”, “B”, “A + B”, or cur rentlyse lected chan nel, is ac ti vated along with the “WTA” but -ton. The “WTA” but ton ac ti vates the nearby red LED aswell as the soft ware se lected In ter com Chan nel “TALK”LED if not al ready ac tive.
3. Stage An nounce (SA) - When pressed, the user’s au dio isrouted to the stage an nounce con nec tor on the back of thebase sta tion. The user also loses their sidetone as an in di -ca tion that stage an nounce is ac ti vated. The other wire lessbeltpacks and wired us ers do not hear the user’s au dio.The but ton is non-latching and ac ti vates the nearby redLED.
4. Talk But ton - Press to en able the au dio path to ei ther In -ter com Chan nel “A” or “B” or “A + B”, from the lo calhead set mi cro phone. The as so ci ated “TALK” LED, #6,will turn red when en abled. A quick press and re leaselatches the talk func tion, un less latch ing has been dis -abled. Holding the but ton for over ½ sec ond, will causethe au dio path to be en abled only for as long as the but tonis held. If the talk func tion is latched on, press ing the talkbut ton again will turn it off.
5. Low Bat tery/Overmodulation (BAT/OM) Light - Lightwill flash once when unit is turned on if the bat tery isgood. If the light stays on, bat tery is low. If the light doesnot flash, bat tery is dead. A nor mal mi cro phone gain set -ting will cause the LED to flash at the be gin ning of mostwords at nor mal speech lev els. If the gain is too high, theLED will be red dur ing the com plete word at nor malspeech lev els.
6. Talk Light - Will turn red when en abled by as so ci ated“TALK” or “WTA” but ton.
4-1
VOL
OFF
SA
WTA
Telex R
TALK
VOL
OFF
TALK
A B
BAT/OM
1 2 3 1
6 6
445
Section
4
![Page 16: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/16.jpg)
Con trols and Con nec tions - Rear Panel
Fig ure 8 TR-825 Rear Panel/Con nec tor/An tennas
1. [MENU] and [SET] but tons – Used to se lect menus andset op tions on the LCD.
2. LCD (Liq uid Crys tal Dis play)
3. [UP] and [DOWN] but tons – Used to se lect beltpack op -tions on the LCD.
4. Mi cro phone Gain – Ad justs the head set’s mi cro phonegain. Ad just so that the BAT/OM LED will flash at the be -gin ning of most words at nor mal speech lev els
5. Push-to-Talk/Push-to-Transmit Switch – Push-to-Talk (PT TALK) – The trans mit ter is al wayson. No au dio sent un less the talk switch, WTA or SAbut ton pressed. Rec om mended po si tion.
Push-to-Transmit (PT TX) - The trans mit ter and au dio path are off ex cept when the talk switch, WTA or SAbut ton is pressed.
6. Head set Con nec tor – Male XLR con nec tor for Telexunits, Fe male XLR con nec tor for RTS units. A dy namic or electret head set mi cro phone is au to mat i cally de tected bythe beltpack and a bias volt age sup plied if needed. Fourpin Telex/RTS units are mon au ral. Five pin Telex/RTSunits have a soft ware set-up which grounds or opens pin 3.
Fig ure 9Head set Jack Wir ing
Sin gle sided 5-pin head sets will only re ceive A or B, de pend --ing on how head phone is wired. These head sets must have thebeltpack set for [Ab SEP]
7. Bat tery Latch – Press down to en able the bat tery pack tobe re leased. While the latch is held down, slide the bat tery pack about 1/8 inch back, to ward the latch, un til it stops.Then lift out.
8. Re ceive An tenna – Screw type ¼-wave re place able an -tenna. The color dot on the screw end of the an tenna mustmatch color dot on an tenna re cep ta cle.
9. Trans mit An tenna – Screw type ¼-wave re place able an -tenna. The color dot on the screw end of the an tenna mustmatch color dot on an tenna re cep ta cle.
4-2
(1) MicrophoneShield (-)
(2) MicrophoneAudio (+)
(4) HeadphoneLow (-)
(3) HeadphoneHigh (+)
ME
NU
SE
T
MIC PTTX
PTTALK
66
7788
99
ME
NU
SE
T
MIC PTTX
PTTALK
22
11
33
44
55
(1) MicrophoneShield (-)
(3) SwitchedHeadphone Ground
(2) MicrophoneAudio (+)
(4) Headphone (Audio A)(5) Headphone
(Audio B)
(1) MicrophoneShield (-)
(4) HeadphoneLow (-)
(3) HeadphoneHigh (+)
(2) MicrophoneAudio (+)
RTS Units
Telex Units
(1) MicrophoneShield (-)
(2) MicrophoneAudio (+)
(5) HeadphoneAudio B
(4) HeadphoneAudio A
(3) Switched Headphone Ground
Menu Set
[ Ab SEP ]
[ Ab Add ]
PIN 3
GND
OPEN
RESULT ON 5-PINDUAL HEADPHONE
A in one side, B in other side
A + B
![Page 17: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/17.jpg)
4-3
TR-825Spec i fi ca tions
RF Fre quency Range . . . . . . . . . . . . . . . . . . . . . . 470 - 608 MHz, 614 - 740 MHz in 18 MHz TX and RX bands
Power Re quire ments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 “AA” Cells Al ka line (NiMH op tional)
Cur rent Draw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190 mA (Push-to-Talk, A and B Talk On)
Tem per a ture Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -4° F to 130° F (-20° C to 55° C)
Di men sions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.75” W x 5.35” H x 2.02” D (9.5 cm x 13.5 cm x 5.1 cm)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 oz (595g) with al ka line bat ter ies
TX An tenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4 Wave (sup plied), Screw type, Re place able
RX An tenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4 Wave (sup plied), Screw type, Re place able
FCC ID: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B5DM517
Fre quency Re sponse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300Hz-8kHz
Mi cro phone in put sen si tiv ity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 mV
Lo cal Head set Out put. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 mW out put into 600W (1% dis tor tion)
Trans mit ter
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Syn the sized, 712 chan nels
Trans mit Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mW Max. (auto-power re duc tion)
Mod u la tion Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FM
De vi a tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 kHz (35 kHz Eu rope)
RF Fre quency Sta bil ity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.005%
Mod u la tion Lim iter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Peak-Responding Com pres sor
Ra di ated Har monics & Spu ri ous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ex ceeds FCC spec i fi ca tions
Re ceiver
Type. . . . . . . . . . . . . . . . . . Two, Dual Con ver sion Super het ero dyne Receivers, Syn the sized, FM, 712 chan nels
RF Sen si tiv ity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <0.8 µV for 12 dB SINAD
Squelch Thresh old . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 dB SINAD (About 1.0 µV)
IF Se lec tiv ity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 dB at 230 kHz
Im age Re jec tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 dB or better
Squelch Quieting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 dB
RF Fre quency Sta bil ity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.005%
Dis tor tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <1% at full de vi a tion
![Page 18: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/18.jpg)
4-4 Blank
![Page 19: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/19.jpg)
Ini tial Equip ment Set-Up
Un packing
Un pack your RadioCom™ Sys tem. Be low are the items thatshould come with your base sta tion and each belt pack.
BTR-800
TR-800, TR-825
Con tact the ship per or your dealer im me di ately if any thing isdam aged or miss ing. Fill out the reg is tra tion card and re turn itto Telex to reg is ter the unit.
5-1
Quan tity De scrip tion
1 BTR-800 Base Sta tion
1 Op er ating In struc tions
1 Power Cord
2 An tennas (one Trans mit and one Re ceive)
1 War ranty Card
1 Screw driver
1 2 ter mi nal plug (for SA Re lay)
1 Warn ing Card
4 Rub ber feet
Quan tity De scrip tion
1 TR-8XX with An tennas
1 Bat tery pack
1 In struc tion Sheet
1 Screw driver
1 War ranty Card
Section
5
![Page 20: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/20.jpg)
An tenna Con nec tion
The base sta tion is sup plied with two (2) an ten nas. One1/2-wave an tenna for Trans mit and one 1/2-wave for Re ceive.The an ten nas have TNC male con nec tors.
The fre quency range of the an ten nas should match the re ceiver and trans mit ter of the base sta tion. Match the color code onthe an tenna with the color code on the base sta tion.
At tach the trans mit 1/2-wave an tenna to the an tenna in put re --cep ta cle la beled “Trans mit” on the right side of the rear panel.The an tenna should be ver ti cally aligned.
Fig ure 10Attaching Trans mit 1/2-Wave An tenna
At tach the re ceive 1/2-wave an tenna to the an tenna in put re --cep ta cle la beled “Re ceive” on the left side of the rear panel.The an tenna should be ver ti cally aligned.
Fig ure 11Attaching Re ceive 1/2-Wave An tenna
An tenna Po lar iza tion
The Telex Wire less In ter com Sys tem is “Ver ti cally Po lar ized”. This means both the trans mit ting and re ceiv ing an ten nasshould op er ate in the ver ti cal po si tion.
Fig ure 12Ver ti cally Po lar ized An tennas
Dis tance be tween An tennas
The dis tance be tween the base sta tion’s re ceive and trans mitan ten nas is not ad just able when the an ten nas are con nected di --rectly on the back of the unit.
The an ten nas can be remoted for better sig nal path. A Telexcoax as sem bly with re mote an ten nas may be re quired. See"Ac ces sory" sec tion fr or der ing information.
NOTE: If your base sta tion is to be lo cated in a shielded rackmount en clo sure or other poor RF lo ca tion, you must re motethe 1/2-wave an ten nas with coax as sem blies. See "Ac ces sories and Re place ment Parts" sec tion for re mote mount ing hard --ware.
An tenna Place ment
Proper an tenna place ment prob a bly has the most ef fect onyour TELEX Wire less In ter com Sys tem’s over all per for --mance. The fol low ing sug ges tions will re sult in op ti mum per --for mance.
Proper place ment of the beltpack can be crit i cal. The an ten nasshould be in the open. Bending the an ten nas up and plac ingthe beltpack in a pocket, etc., will re duce sys tem dis tance.
It is sug gested that the unit be worn on the belt with both an --tenna’s ver ti cal for best op er at ing range and per for mance.
Fig ure 13Proper Dress ing of the An tennas
5-2
TelexWTA
AB
OFF
BAT/OM TALK
RadioComTR-800
TM
VOL
SA
TALK
MIC GAIN
TALK/O.M.VOLUME
SELECT
A
B
ON/O.M.
ON/OFF
IN
OUT
AUXILIARYINTERCOM B
2 WIRE
4 WIRE
SELECT
IN
OUT
2 WIRE
4 WIRE
SELECT
IN
OUT
INTERCOM APORTABLE STATION CONNECT
1 2 3 4
UP
DOWN
MENU
SET
RadioComä BTR-800
ClearScanTM
COPY
ANTENNAS SHOULD BE VERTICAL
TelexWTA
AB
OFF
BAT/OM TALK
RadioComTR-800
TM
VOL
SA
![Page 21: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/21.jpg)
Keep the dis tance be tween the base sta tion and the beltpacksas short as pos si ble. The greater the dis tance, the weaker thesig nal. Make sure the “sig nal paths” be tween the base sta tionand beltpacks are un ob structed. You should be able to vis i blylo cate the base sta tion an ten nas at all times for best per for --mance.
Fig ure 14Dis tance Be tween base sta tion and beltpack
Fig ure 15Keeping Site Clear to An tenna
At tempting to op er ate the wire less in ter com sys tem through or around walls, ceil ings, metal ob jects, etc. will re duce sys temrange and per for mance.
Fig ure 16Op er ating Sys tem Near Ob struc tions
DO NOT - mount the base sta tion 1/2-wave an ten nas on, ornext to metal, such as beams, walls with metal studs, equip --ment racks, etc. This also ap plies to the an ten nas when as sem --bled di rectly to the Base Sta tion. This will “de tune” thean ten nas which can re sult in noise or loss of RF sig nal at theBase Sta tion, see Fig ure 17.
5-3
700 FEET
100 FEET
TelexWTA
AB
OFF
BAT/OM TALK
RadioComTR-800
TM
VOL
SA
TALK
MIC GAIN
TALK/O.M.VOLUME
SELECT
A
B
ON/O.M.
ON/OFF
IN
OUT
AUXILIARYINTERCOM B
2 WIRE
4 WIRE
SELECT
IN
OUT
2 WIRE
4 WIRE
SELECT
IN
OUT
INTERCOM APORTABLE STATION CONNECT
1 2 3 4
UP
DOWN
MENU
SET
RadioComä BTR-800
ClearScanTM
COPY
TelexWTA
AB
OFF
BAT/OM TALK
RadioComTR-800
TM
VOL
SA
TelexWTA WTA
AB
OFF OFF
BAT/OM TALK
RadioComTR-800
TMTM
VOL VOL
SASA
TelexWTA
AB
OFF
BAT/OM TALK
RadioComTR-800
TM
VOL
SA
TALK
MIC GAIN
TALK/O.M.VOLUME
SELECT
A
B
ON/O.M.
ON/OFF
IN
OUT
AUXILIARYINTERCOM B
2 WIRE
4 WIRE
SELECT
IN
OUT
2 WIRE
4 WIRE
SELECT
IN
OUT
INTERCOM APORTABLE STATION CONNECT
1 2 3 4
UP
DOWN
MENU
SET
RadioComä BTR-800
ClearScanTM
COPY
Telex
OFF
BAT/OM TALK
RadioComTR-700
TM
VOL
TALK
MIC GAIN
TALK/O.M.VOLUME
SELECT
A
B
ON/O.M.
ON/OFF
IN
OUT
AUXILIARYINTERCOM B
2 WIRE
4 WIRE
SELECT
IN
OUT
2 WIRE
4 WIRE
SELECT
IN
OUT
INTERCOM APORTABLE STATION CONNECT
1 2 3 4
UP
DOWN
MENU
SET
RadioComä BTR-800
ClearScan
COPY
![Page 22: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/22.jpg)
Fig ure 17An tenna Place ment
Im proving Re cep tion and In creasingRange
Keeping the dis tance from the base sta tion and beltpack asshort, and un ob structed as pos si ble will pro duce the most re li --able per for mance.
The base sta tion is sup plied with two an ten nas. This shouldpro vide sat is fac tory sys tem per for mance in most ap pli ca tions.Sys tem range can be en hanced by remoting the 1/2-wave an --ten nas. The ½ wave an ten nas are ground plane in de pend ent,so a ground plane is not re quired for good per for mance.
5-4
Telex
UHF ANTENNA SPLITTER/COMBINER
SC - 600TelexR
Telex Telex
UHF ANTENNA SPLITTER/COMBINER
SC - 600TelexR
#1 #2 #3
TALKTALK
MIC GAINMIC GAIN
TALK/O.M.TALK/O.M.VOLUMEVOLUME
SELECTSELECT
AA
BB
ON/O.M.ON/O.M.
ON/OFFON/OFF
ININ
OUTOUT
AUXILIARYAUXILIARYINTERCOM BINTERCOM B
2 WIRE2 WIRE
4 WIRE4 WIRE
SELECTSELECT
ININ
OUTOUT
2 WIRE2 WIRE
4 WIRE4 WIRE
SELECTSELECT
ININ
OUTOUT
INTERCOM AINTERCOM APORTABLE STATION CONNECTPORTABLE STATION CONNECT
11 22 33 44
UPUP
DOWNDOWN
MENUMENU
SETSET
RadioComä BTR-800
ClearScanClearScanTMTM
COPY
TALKTALK
MIC GAINMIC GAIN
TALK/O.M.TALK/O.M.VOLUMEVOLUME
SELECTSELECT
AA
BB
ON/O.M.ON/O.M.
ON/OFFON/OFF
ININ
OUTOUT
AUXILIARYAUXILIARYINTERCOM BINTERCOM B
2 WIRE2 WIRE
4 WIRE4 WIRE
SELECTSELECT
ININ
OUTOUT
2 WIRE2 WIRE
4 WIRE4 WIRE
SELECTSELECT
ININ
OUTOUT
INTERCOM AINTERCOM APORTABLE STATION CONNECTPORTABLE STATION CONNECT
11 22 33 44
UPUP
DOWNDOWN
MENUMENU
SETSET
RadioComä BTR-800
ClearScanClearScanTMTM
COPYCOPY
TALKTALK
MIC GAINMIC GAIN
TALK/O.M.TALK/O.M.VOLUMEVOLUME
SELECTSELECT
AA
BB
ON/O.M.ON/O.M.
ON/OFFON/OFF
ININ
OUTOUT
AUXILIARYAUXILIARYINTERCOM BINTERCOM B
2 WIRE2 WIRE
4 WIRE4 WIRE
SELECTSELECT
ININ
OUTOUT
2 WIRE2 WIRE
4 WIRE4 WIRE
SELECTSELECT
ININ
OUTOUT
INTERCOM AINTERCOM APORTABLE STATION CONNECTPORTABLE STATION CONNECT
11 22 33 44
UPUP
DOWNDOWN
MENUMENU
SETSET
RadioComä BTR-800
ClearScanClearScanTMTM
COPYCOPY
TALKTALK
MIC GAINMIC GAIN
TALK/O.M.TALK/O.M.VOLUMEVOLUME
SELECTSELECT
AA
BB
ON/O.M.ON/O.M.
ON/OFFON/OFF
ININ
OUTOUT
AUXILIARYAUXILIARYINTERCOM BINTERCOM B
2 WIRE2 WIRE
4 WIRE4 WIRE
SELECTSELECT
ININ
OUTOUT
2 WIRE2 WIRE
4 WIRE4 WIRE
SELECTSELECT
ININ
OUTOUT
INTERCOM AINTERCOM APORTABLE STATION CONNECTPORTABLE STATION CONNECT
11 22 33 44
UPUP
DOWNDOWN
MENUMENU
SETSET
RadioComRadioComää BTR-800BTR-800
ClearScanClearScanTMTM
COPYCOPY
TALKTALK
MIC GAINMIC GAIN
TALK/O.M.TALK/O.M.VOLUMEVOLUME
SELECTSELECT
AA
BB
ON/O.M.ON/O.M.
ON/OFFON/OFF
ININ
OUTOUT
AUXILIARYAUXILIARYINTERCOM BINTERCOM B
2 WIRE2 WIRE
4 WIRE4 WIRE
SELECTSELECT
ININ
OUTOUT
2 WIRE2 WIRE
4 WIRE4 WIRE
SELECTSELECT
ININ
OUTOUT
INTERCOM AINTERCOM APORTABLE STATION CONNECTPORTABLE STATION CONNECT
11 22 33 44
UPUP
DOWNDOWN
MENUMENU
SETSET
RadioComRadioComää BTR-800BTR-800
ClearScanClearScanTMTM
COPYCOPY
1. Placing BTRs in a shelf orequip ment rack and us ing re -mote an ten nas is OK.
2. Placing the BTR on top of a shelf or equip ment rack un -ob structed with out remoting the an ten nas is OK.
3. Placing BTRs in a shelf orequip ment rack with the an -ten nas mounted on the backof the BTR or the side of the rack is BAD.
![Page 23: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/23.jpg)
Base Sta tion Set-up
Lo ca tion
Lo cate the base sta tion with the front and rear of the unit ac --ces si ble so that switches may be set and con nec tions made.Place the trans mit and re ceive an ten nas on the base sta tion.Make sure the an tenna’s color band match the color dot neareach an tenna. See “An tenna In for ma tion” sec tion for more in --for ma tion on choos ing a proper op er at ing lo ca tion.
Power Con nec tion
Plug the sup plied power cord into the unit. The base sta tion hasan IEC power re cep ta cle that ac cepts 100 – 240 VAC, 50 – 60Hz. The spe cific re cep ta cle type is an IEC 60320/C14. The cordit ac cepts is an IEC 60320/C13. These cords are com mon andavail able through many re tail hard ware/elec tronic stores if thecord is lost.
Trans mit Switches
There are two switches lo cated on the lower left side of the rearpanel. The up per switch sets the trans mit power lev els to highor nor mal. The lower switch turns the trans mit ters on or off.
Trans mit Power
Set the power level to nor mal if us ing the beltpacks atc lose to me dium dis tances (<200 feet, 161m,line-of-sight) from the base sta tion. Set the power level tohigh if us ing the beltpacks at a dis tance (>200 feet, 161m, line-of-sight) from the base sta tion.
On/Off
Set the trans mit ter switch to on for nor mal use. In the offpo si tion both base sta tion trans mit ters are dis abled. Set --ting the switch to off will dis able all the beltpacks fromhear ing any one else or even their own sidetone.
5-5
RECEIVE
HIGH
ON
NORM
OFF
TRANSMITPOWER
I/C
TELEX CLEARCOMRTS
BTR-800FCC ID: B5DM514
CANADA 1321231218A
BASE STATIONLINK
RELAYCONTACT
INTERCOM A2 WIRE
LOOP
THRU
4 WIRE
INTERCOM B2 WIRE
LOOP
THRU
4 WIRE
AUXILIARY AUDIO
INPUT OUTPUT
STAGE ANNOUNCE
OUTPUT POWER
100-240 VAC 50-60 Hz
TRANSMIT
MADE IN USA
PUSHPUSHPUSH
TelexTelex Communications, Inc.
POWER CONNECTION
INTERCOMSWITCH
TRANSMITSWITCHES
INTERCOMINTERFACE
Fig ure 18Base Sta tion - Rear Panel
![Page 24: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/24.jpg)
In ter nal Trans mit Switches
In ter nal to the BTR-800 are two trans mit switches which en --able a user to turn on or off the two trans mit ters in di vid u ally.See Fig ure 19 for the lo ca tion. The top cover of the base sta --tion must be re moved for ac cess. The switch clos est to thefront panel con trols trans mit ter 1 (au dio chan nel A). Theswitch be hind that is trans mit ter 2 (au dio chan nel B). The de --fault switch po si tion is to the left if you are fac ing the front ofthe base sta tion. This is the “ON” po si tion for the trans mit ters.
In the nor mal use of the BTR-800, there is no need to ac cessthese switches. They are used to test the trans mit ters in di vid u --ally at the fac tory.
Fig ure 19In ter nal Trans mit Switches
In ter com Switch
The RadioCom® wire less sys tem can be in ter faced to RTS,TW, Audiocom® (Telex), Clear-Com®, RTS ma trix and otherin ter com (I/C) sys tems. Set the In ter com switch on the rear ofthe unit to the ap pro pri ate sys tem and con nect the sys tem tothe base sta tion. The two in ter com chan nels on the rear of thebase sta tion have loop-thru male and fe male XLR con nec tions for two-wire sys tems and RJ-11 type jacks for four-wire sys --tems.
This switch only af fects the two-wire in ter com sys tems. Thefunc tions of the I/C XLRs change de pend ing on the in ter comse lected. Please see Sec tion 12 for pinout in for ma tion of thedif fer ent two-wire in ter com sys tems.
In ter com In ter face
Telex (Audiocom®) and Clear-Com® in ter com sys tems re --quire one ca ble for in ter com A and one ca ble for in ter com B in or der to in ter face two chan nels of in ter com to the base sta tion. This in ter fac ing is done through the I/C A and B 3-pin XLRcon nec tors on the rear of the unit.
RTS TW in ter coms only need to con nect one 3-pin ca ble toone of the four in ter com XLR con nec tors since two chan nelsof au dio are car ried on one ca ble. The in ter com switch par al --lels the four XLR con nec tors when in RTS mode. RTS chan --nel 1 is placed on in ter com A and RTS chan nel 2 is placed onin ter com B as long as the RTS TW in put to the base sta tion iswired as in Sec tion 12.
Four-wire in ter com sys tems re quire one ca ble for in ter com Aand one ca ble for in ter com B in or der to in ter face two chan --nels of four-wire in ter com to the base sta tion. This in ter fac ingis done through the I/C A and B RJ-11 type jacks on the rearof the unit. See Fig ure 20 for the pinout of the RJ-11 jacks.
Fig ure 20RJ-11 Type/ Four-wire Pinout
5-6
ON
ON
S3OFF
S4OFF
Transmitter 2
Transmitter 1
FRONT
BACKBACK
NC
AUDIO IN +
AUDIO OUT +AUDIO OUT -
AUDIO IN -
NC
PIN 6 5 4 3 2 1
![Page 25: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/25.jpg)
5-7
TelexWTA
AB
OFF
BAT/OM TALK
RadioComTR-800
TM
VOL
SA
TelexWTA
AB
OFF
BAT/OM TALK
RadioComTR-800
TM
VOL
SA
TelexWTA
AB
OFF
BAT/OM TALK
RadioComTR-800
TM
VOL
SA
TelexWTA
AB
OFF
BAT/OM TALK
RadioComTR-800
TM
VOL
SA
MODEL PS15POWER SUPPLYO/N 9000678600
IMPEDANCESELECT
NORM
200
DUAL
400
OUTPUTS J1, J2 CONNECT TO
J1 J2 TW INTERCOM SYSTEM COMPONENTSREFER TO OPERATION MANUAL
AUDIOCOUPLINGCM1-CM2
J3
TIP-CH1RING-CH2SLEEVE-COM
RTS SYSTEMS, BURBANK CALIFORNIA MADE IN U.S.A.
FUSE0.5A S8/120 VAC
CAUTIONFOR CONTINUED PROTECTION AGAINST FIREREPLACE ONLY WITH SAME TYPE FUSE.
CHN 1CHN 1
HEADSET LINE
HEADSET LINE
HEADSET LINE
HEADSET LINE
INTERCOMPOWER SUPPLY
RTS DISTRIBUTIONPANEL (TW5W)
BP-318
BP-350
BP-350
RECEIVE
HIGH
ON
NORM
OFF
TRANSMITPOWER
I/C
TELEX CLEARCOMRTS
BTR-800FCC ID: B5DM514
CANADA 1321231218A
BASE STATIONLINK
RELAYCONTACT
INTERCOM A2 WIRE
LOOP
THRU
4 WIRE
INTERCOM B2 WIRE
LOOP
THRU
4 WIRE
AUXILIARY AUDIO
INPUT OUTPUT
STAGE ANNOUNCE
OUTPUT POWER
100-240 VAC 50-60 Hz
TRANSMIT
MADE IN USA
PUSHPUSHPUSH
TelexTelex Communications, Inc.
RECEIVE
HIGH
ON
NORM
OFF
BP-318
BTR-800
TR-800’sor
TR-825’s
(PS15)
Fig ure 21Ex am ple In ter face to an RTS TW Sys tem
![Page 26: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/26.jpg)
Dual Lis ten Func tion al ity
The base sta tions's main au dio board has the op tion of plac ingad di tional parts to en able dual lis ten. Dual lis ten al lows themix ing of the in ter com chan nels. The mix ing will oc cur lo --cally, within the base sta tion, and is only heard on that basesta tion's beltpacks. The user will have the abil ity to en able/dis --able the mix of I/C A into I/C B or vise versa. If you haveTR-825 beltpacks, there is no need to in stall this base op tion.The level of the mix can be controlled at the TR-825 via thetwo vol ume con trols.
They will also have the abil ity to con trol the level of the mix(-4 dB to -24 dB down from main chan nel). Re moving twosur face mount re sis tors and in stall ing two SPDT switches andtwo po ten ti om e ter en ables dual lis ten. The parts to be in stalled are shown in Ta ble 1. The two re sis tors on the board to be re --moved are in Ta ble 2.
Ta ble 1Parts to be In stalled by User to En able Dual Lis ten
Ta ble 2Parts to be Re moved by User to En able Dual Lis ten
The listed man u fac tures and part num bers in Ta ble 1 are thosethat the au dio board was laid out for and thus the hole pat ternused. Sev eral of these parts may be found at Digi-Key andother dis trib u tors. Trim the leads on the parts so they can nothit the metal case. Lo ca tions to place these com po nents arepro vided on au dio board part num ber 750608 andASY000108000.
The au dio board part num ber is lo cated on the lower left handside of the board if fac ing the front of the unit. The lo ca tionswhere the com po nents can be in stalled are on the up per righthand side of the board. See Fig ure 22 for the lo ca tions. Boardpart num ber 750541 does not have lo ca tions to place com po --nents, how ever, mod i fi ca tion doc u ments may be ob tainedfrom Telex Com mu ni ca tions for those who wish to mod ifyolder au dio boards for dual lis ten.
Fig ure 22Au dio Board Part Num ber and Dual Lis ten Com po nent Lo ca tions
5-8
BoardDes ig na tor De scrip tion and Func tion Value Man u fac turers, Part No.
VR5, VR6 Po ten ti om e ters 20kW - 25kW Bourns, 3309P-1-203VR5 = Con trols I/C A into I/C B Mix CTS, U262R253BVR6 = Con trols I/C B into I/C A Mix Piher, PT10LV10-203A2020
S6, S7 Switches SPDT E-Switch, 500ASSP1M2RES6 = En able/Dis able I/C A into I/C B Mix E-Switch, EG1218S7 = En able/Dis able I/C B into I/C A Mix Alcoswitch, TSS11DGPC
BoardDes ig na tor De scrip tion and Func tion Value
R295 Re sis tor, De fault if mix com po nents not in stalled 10k
R296 Re sis tor, De fault if mix com po nents not in stalled 10k
FRONT
BACK
B INTO AMIX
B INTO AMIX
OFFOFF
ONONONON
IF PARTS INSTALLEDREMOVE R296
S7S7
S6S6
R2
96
R2
96
R2
98
R2
98
VR
6V
R6
MIXLEVEL
MIXLEVEL
OFFOFF
ONONONON
IF PARTS INSTALLEDREMOVE R295
R2
95
R2
95
R2
97
R2
97
VR
5V
R5
MIXLEVEL
MIXLEVEL
A INTO BMIX
A INTO BMIX
B INTO AMIX
B INTO AMIX
OFFOFF
ONONONON
IF PARTS INSTALLEDREMOVE R296
S7S7
S6S6
R2
96
R2
96
R2
98
R2
98
VR
6V
R6
MIXLEVEL
MIXLEVEL
OFFOFF
ONONONON
IF PARTS INSTALLEDREMOVE R295
R2
95
R2
95
R2
97
R2
97
VR
5V
R5
MIXLEVEL
MIXLEVEL
A INTO BMIX
A INTO BMIX
750608 REV X879416- 1 REV J
750608 REV X879416- 1 REV J
ASY000108000 REV XASY000109 - X REV XOR
![Page 27: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/27.jpg)
Aux il iary In put/Out put
The in put and out put 3-pin XLR aux il iary con nec tions are forsup ply ing ad di tional bal anced au dio into and re ceiv ing bal --anced au dio from the base sta tion. The out put aux il iary con --nec tion only in ter faces to in ter com B. How ever, there is anin ter nal switch to con trol the rout ing of the in put aux il iary au --dio. See the "In ter nal Aux il iary In put Routing Switch" sec tionof this man ual.
The in put and out put aux il iary au dio is global. This meansthe in put aux il iary au dio is placed on the base lo cal head set,beltpack(s), head sets, and any wired in ter com sys tem in ter --faced to the base sta tion. The in ter com chan nel(s) the in putaux il iary au dio is placed on de pends on the po si tion of the in --put rout ing switch.
The out put aux il iary au dio is also taken from the in ter com Bbase lo cal head set, beltpack(s), head sets, and any wired in ter --com con nected to the base sta tion. A mod i fi ca tion doc u ment is avail able from Telex Communications for those who wish to mod ify the base sta tion so that aux il iary in put au dio is heardonly lo cally; base lo cal head set and beltpack(s) head sets.
In ter nal Aux il iary In put Routing Switch
This switch con trols the rout ing of the in put aux il iary au dio.This switch has two po si tions. The "B" po si tion places aux il --iary in put au dio onto in ter com B only (de fault from fac tory).The "A & B" po si tion places aux il iary in put au dio onto in ter --com A and B. Please see Fig ure 23 for the lo ca tion of this in --ter nal aux il iary in put rout ing switch.
Fig ure 23Aux il iary In put Routing Switch
5-9
FRONT
BACK
B INTO AMIX
B INTO AMIX
OFFOFF
ONONONON
IF PARTS INSTALLEDREMOVE R296
S7S7
S6S6
R296
R296
R298
R298
VR
6V
R6
MIXLEVEL
MIXLEVEL
OFFOFF
ONONONON
IF PARTS INSTALLEDREMOVE R295
R295
R295
R297
R297
VR
5V
R5
MIXLEVEL
MIXLEVEL
A INTO BMIX
A INTO BMIX
750608 REV X879416- 1 REV J
ONON
BB
A & BA & B
AUX INAUX IN
R294
R294
R293
R293
S5S5
IF PARTS INSTALLEDREMOVE R295
B
A & B
AUX IN
R294
R293
S5
AUXILIARY INPUTROUTING SWITCH
![Page 28: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/28.jpg)
Stage An nounce / Re lay Con tacts
The stage an nounce out put con nec tor is where au dio ex its thebase when any of the beltpacks press the [SA] but ton. Theout put is bal anced au dio though a male 3-pin XLR. The stagean nounce out put level is set at the fac tory for 2 Vrms typ i calout put at rated de vi a tion into 600 Ohms. This should be ad e --quate for most ap pli ca tions. There is an in ter nal level ad just --ment for this out put too. See Fig ure 26 for the lo ca tion of thesmall level trim mer. The top cover of the base sta tion must bere moved for ac cess.
A re lay con tact clo sure is also ac ti vated when a beltpack userpresses the [SA] but ton. The con tacts are nor mal open (N.O.).Rat ing: 1 Amp at 24 volts AC/DC max i mum. A “Phoe nix”type con nec tor (sup plied) plugs into the re lay con tact port onthe rear of the base sta tion. This con nec tor pro vides ascrew-type clo sure for an easy con nec tion to wires.
5-10
U21
VR4
STAGE ANNOUNCE LEVEL CONTROL
FRONT
BACK
1 2
PHOENIXTYPE
CONNECTOR
Fig ure 26In ter nal Stage An nounce Level Con trol
Fig ure 25Re lay Con tact Jack Adapter(Screw Ter mi nal Adapter)
RECEIVE
HIGH
ON
NORM
OFF
TRANSMITPOWER
I/C
TELEX CLEARCOMRTS
BTR-800FCC ID: B5DM514
CANADA 1321231218A
BASE STATIONLINK
RELAYCONTACT
INTERCOM A2 WIRE
LOOP
THRU
4 WIRE
INTERCOM B2 WIRE
LOOP
THRU
4 WIRE
AUXILIARY AUDIO
INPUT OUTPUT
STAGE ANNOUNCE
OUTPUT POWER
100-240 VAC 50-60 Hz
TRANSMIT
MADE IN USA
PUSHPUSHPUSH
TelexTelex Communications, Inc.
AUXILIARYINTERFACE
STAGE ANNOUNCESTAGE ANNOUNCE RELAY
Base Sta tion - Rear Panel
PIN 1
PIN 2
Fig ure 24Re lay Out put Schematic
![Page 29: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/29.jpg)
Base Sta tion Link
This RJ-45 type jack al lows the con nec tion of wire less talkaround (WTA) to two base sta tions of the same fre quencybands. This al lows WTA on I/C chan nel A and WTA on I/Cchan nel B to be the car ried through to the other base sta tionat tached to gether via this jack.
WTA chan nel A and chan nel B is “con tained” within a basesta tion un less the trans mit power is off. If it is off, the WTAau dio is routed through the base sta tion link ca ble to the otherbase that has its trans mit ters on.
A ca ble to ac com plish this task is NOT sup plied, but can eas --ily be made with com mon cat e gory 5 (CAT-5) wir ing.
In fact, the most com mon 10BaseT ether net patch ca bles,568-B wired ca bles, can be used to con nect bases to gether.The re quired ca ble is shown be low.
The reg u lar two-wire in ter com chan nels are passed from baseto base via the wired in ter com ca bles and do not re quire thebase sta tion link ca ble.
5-11
RECEIVE
HIGH
ON
NORM
OFF
TRANSMITPOWER
I/C
TELEX CLEARCOMRTS
BTR-800FCC ID: B5DM514
CANADA 1321231218A
BASE STATIONLINK
RELAYCONTACT
INTERCOM A2 WIRE
LOOP
THRU
4 WIRE
INTERCOM B2 WIRE
LOOP
THRU
4 WIRE
AUXILIARY AUDIO
INPUT OUTPUT
STAGE ANNOUNCE
OUTPUT POWER
100-240 VAC 50-60 Hz
TRANSMIT
MADE IN USA
PUSHPUSHPUSH
TelexTelex Communications, Inc.
RECEIVE
HIGH
ON
NORM
OFF
RECEIVE
HIGH
ON
NORM
OFF
TRANSMITPOWER
I/C
TELEX CLEARCOMRTS
BTR-800FCC ID: B5DM514
CANADA 1321231218A
BASE STATIONLINK
RELAYCONTACT
INTERCOM A2 WIRE
LOOP
THRU
4 WIRE
INTERCOM B2 WIRE
LOOP
THRU
4 WIRE
AUXILIARY AUDIO
INPUT OUTPUT
STAGE ANNOUNCE
OUTPUT POWER
100-240 VAC 50-60 Hz
TRANSMIT
MADE IN USA
PUSHPUSHPUSH
TelexTelex Communications, Inc.
RECEIVE
HIGH
ON
NORM
OFF
LOAD LOAD
Fig ure 27 Two Stand Alone Base Sta tions Con nected To gether
12345678
WTA A+
WTA A-WTA B-
WTA B+
12345678
WTA A+
WTA A-WTA B-
WTA B+CABLE: ANY CATEGORY 5 TYPE
CABLE LENGTH: KEEP AS SHORT AS POSSIBLE
RJ-45 MALE RJ-45 MALE
Fig ure 28Base Sta tion Link Ca ble
RECEIVE
HIGH
ON
NORM
OFF
TRANSMITPOWER
I/C
TELEX CLEARCOMRTS
BTR-800FCC ID: B5DM514
CANADA 1321231218A
BASE STATIONLINK
RELAYCONTACT
INTERCOM A2 WIRE
LOOP
THRU
4 WIRE
INTERCOM B2 WIRE
LOOP
THRU
4 WIRE
AUXILIARY AUDIO
INPUT OUTPUT
STAGE ANNOUNCE
OUTPUT POWER
100-240 VAC 50-60 Hz
TRANSMIT
MADE IN USA
PUSHPUSHPUSH
TelexTelex Communications, Inc.
BASE STATIONLINK
Base Sta tion - Rear Panel
![Page 30: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/30.jpg)
Beltpack Set-up
Bat tery In stal la tion
En sure that the On/Off vol ume con trol knob is turned off. Press down and hold down the bat tery re lease latch, slide thebat tery pack about 1/8 inch back, to ward the latch, un til itstops. Then lift bat tery pack out. Re place bat ter ies as fol lows:
Fig ure 29Bat tery In stal la tion
5-12
1. Open the bat tery pack by in sert ingfin ger nail and lift ing.
3. Load new bat ter ies fol low ing the po lar ity as shown in bat tery case
5. Be sure strap goes un der bat ter ies.
2. Pull bat tery strap to re move low or dead bat ter ies.
4. Start load ing at the end of the case wherethe strap is at tached to the case.
6. Tuck end of strap un der doorwhen plac ing the bat tery cover back on the case.
WARNING
Do not place an al ka line TR bat terypack in any bat tery charger. Se verecharger and bat tery pack dam agemay re sult.
7. For TR-825, en sure that bothOn/Off vol ume con trol knobsare turned off prior to in sert -ing the bat tery pack onto theTR-825 to pre vent the pos si -bil ity of a volt age spike thatcould cause the unit to be come in op er a ble.
![Page 31: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/31.jpg)
An tenna Con nec tion
The beltpack co mes with two de tach able, screw-type,1/4-wave an ten nas. To at tach the two an ten nas, screw into there cep ta cles at the bot tom of the beltpack. The color dot on thescrew end of the an tenna must match the color dot on an tennare cep ta cle. The re ceive antenna screws into the left re cep ta cleif the beltpack is lay ing flat with the bat tery com part ment faceup and the an tenna re cep ta cles fac ing you. The other an tennais the trans mit an tenna. New an ten nas can be or dered if de --sired, see the “Ac ces sories” sec tion.
Trans mit mode
The rear panel lo cated trans mit switch has the fol low ing twomodes:
Push-to-Talk (PT TALK) – Rec om mended po si tion –The trans mit ter is al ways on. No au dio is sent un less thetalk switch, WTA or SA but ton is pressed.
Push-to-Transmit (PT TX) – The trans mit ter and au diopath are off ex cept when the talk switch, WTA or SA but --ton is pressed.
Head set Con nec tion
In sert the head set plug into the XLR con nec tor. See the head --set pinout in the “TR-800/TR-825” beltpack con trols and con --nec tions” sec tion if this is not a Telex head set. A dy namic orelectret head set mi cro phone is au to mat i cally de tected by thebeltpack and a bias volt age sup plied if needed.
5-13
ME
NU
SE
T
MIC PTTX
PTTALK
MICROPHONEGAIN CONTROL
TRANSMITSWITCH
HEADSETCONNECTION
RECEIVE ANTENNA
TRANSMIT ANTENNA
BATTERYRELEASE
LATCH
Fig ure 30TR-800 and TR-825 Rear Panel
![Page 32: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/32.jpg)
5-14 Blank
![Page 33: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/33.jpg)
Pre-Walk-Thru Check list
Fol low ing the in struc tions fully to this point you have suc cess --fully com pleted the fol low ing check list:
rLo cated the base sta tion prop erly.
rCon nected power to base sta tion.
rCon nected the 1/2-wave an ten nas to the base sta tion.Checked fre quency range of the an ten nas with the fre -quency of the base sta tion by cor rectly match ing colorcodes.
rCon nected 1/4-wave an tenna to the beltpack. Checkedfre quency range of the an ten nas with the fre quency ofthe beltpack by cor rectly match ing color codes.
rBase sta tion trans mit power switches in the cor rect po -si tions.
rTrans mit mode switch on beltpack set cor rectly
rSet wired in ter com type cor rectly.
rCon nected head sets to base sta tions (if needed) and allbeltpacks.
rCon nected the base sta tion to any aux il iary au dio, in -ter com, ex ter nal P.A. sys tem, or re lay con tact de tectcir cuit if needed
r In stalled bat ter ies in the beltpack.
r If you missed any of the above in struc tions, go backand com plete that in struc tion be fore go ing on.
6-1
Section
6
![Page 34: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/34.jpg)
6-2 Blank
![Page 35: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/35.jpg)
System Op er a tion
Fre quency Plan Over view
The BTR/TR-8XX has 36 fac tory de fined fre quency groupsand 12 user-programmable fre quency groups. A Group de --fines the two base sta tion trans mit fre quen cies and thus thetwo re ceive fre quen cies on all the beltpacks. A Chan nel de --fines a base sta tion re ceive fre quency and thus a beltpacktrans mit frequency. A base sta tion re ceive chan nel that doesnot have a fre quency set for it will have a dash to the right ofit on the Group/Chan nel se lect screen. De tails on set ting fre --quen cies may be found in the “BTR-800 Menu Struc ture” and“TR-8XX Menu Struc ture” in struc tions in this sec tion.
Fac tory-Defined Groups
The 36 fac tory-defined groups were care fully cho sen to avoidcer tain intermod prod ucts and var i ous other pos si ble sourcesof in ter fer ence. The Groups are set and can not be changed. There is a lim ited num ber of chan nels which can be chosenfrom within these groups.
The first 24 factory-defined groups (01A – 12B) are “pair”groups that can be used for sin gle (up to 4 beltpacks) and dual(up to 8 beltpacks) BTR-800 sys tems. They are ar ranged01A, 01B, 02A, 02B…011B, 012A, 012B. A “pair” group,like 1A and 1B, have dif fer ent base sta tion transmit fre quen --cies, how ever, they both have the same eight base station re --ceive chan nels from which to choose. Each chan nel rep re sents a unique fre quency. For ex am ple, one BTR-800 could be seton Group 02A and chan nels 01, 02, 03 and 04. The otherBTR-800 could be set on Group 02B chan nels 05, 06, 07 and08. As long as the chan nels are dif fer ent, everything shouldbe fine.
The next 12 groups (13 – 24) are sin gle groups that primarilyare used for sin gle (up to 4 beltpacks) BTR-800 sys tems. Thenum ber of chan nels from which to choose from in thesegroups will vary from group to group.
User-Programmable Groups
The 12 user-programmable groups are ini tially empty. Thetrans mit and re ceive fre quen cies are fully editable within these groups. In fact, fac tory-defined groups may be cop ied touser-programmable groups and then ed ited if de sired. See the“BTR-800 Menu Struc ture” and “TR-8XX Menu Struc ture”in struc tions in this sec tion for de tails on how to copy and editfre quen cies.
Sys tem Quick Start
Fol low the list be low to quickly get a base sta tion andbeltpack(s) op er at ing. When com pleted the user should have abase sta tion and 1 to 4 beltpacks up and run ning with full op er --a tional abil ity. The base sta tion will be on Group 01A with itsfour re ceiv ers on chan nels 01, 02, 03 and 04. Each beltpackwill be on Group 01A with a unique trans mit chan nel num bermatch ing one of the base sta tion re ceive chan nels.
1. Plug-in the base sta tion via the sup plied power cord andcon nect the an ten nas. The color dots on the base shouldmatch the color rings on the an ten nas.
2. Base sta tion rear panel switches: Trans mit power set toHigh and on.
3. En sure base sta tion rear panel IC switch matches at tachedwired in ter com sys tem. If used stand alone or con nected toa 4-wire sys tem then IC switch po si tion is Not Ap pli ca ble.
4. Press [MENU] as pow er ing-up the base sta tion. This willplace it on group 01A and set the re ceives on chan nels: 01, 02, 03, and 04.
5. Place the front panel IC A and IC B “IN” and “OUT” level con trols in the 12:00 o’clock po si tion. Check that frontpanel IC A and B is in 2-wire for AudioCom (Telex), RTS-TW and ClearCom wired sys tems, and 4-wire for RTSMa trix and stand-alone op er a tion.
6. Place bat ter ies in the beltpacks.
7. Re move the rear switch cover on the beltpacks. Set thebeltpack rear panel slide switch to push-to-talk (PTTALK).
8. Press [MENU] as pow er ing-up each beltpack. This willplace the beltpack on group 01A with the chan nel 01flash ing.
9. Use the [UP] and [DOWN] ar row but tons to change thechan nel to match a channel on the base sta tion. Then press [SET]. If leav ing on chan nel, just press [MENU]. Eachbeltpack should have a unique chan nel num ber.
10. The group/chan nel on the beltpack should now match thegroup and a re ceive chan nel on the base sta tion. Noth ingshould be flash ing on the beltpack screens.
11. Plug head sets into the beltpacks and set the mi cro phonegain so the BAT/OM LED will flash at the be gin ning ofmost words at nor mal speech lev els.
DONE.
7-1
Section
7
![Page 36: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/36.jpg)
Base Sta tion Op er a tion
Power
If you have fol lowed the in struc tions in Sec tion 4, “Ini tialEquip ment Set-Up”, you should now be ready to turn the base sta tion on.
Set the base sta tion power switch to the on po si tion, by push --ing the top of the switch.The in ter nal cool ing fan will start im --me di ately and the LCD dis play and front panel in di ca tor lights will come on in five or six sec onds.
Lo cal Head set
Talk But ton - Press to en able the au dio path from the lo cal head set. The TALK/O.M. LED will turn green when au dio is en abled. A quick press and re lease latches on the but ton. If the talk function is latched on, press ing the talk but tonagain will turn it off. If the lo cal head set is not be ing used, the talk but ton should be off. This keeps ad di tional noiseout of the sys tem.
Mi cro phone Gain - Ad justs the head set’s mi cro phonegain. Ad just so the TALK/O.M. LED flashes from greento red on loudest speech.
Head set In ter com Se lect But ton - Se lect the in ter comsys tem to con nect to the lo cal head set. Each press of the[SE LECT] but ton changes the con nec tion; Chan nel A,Chan nel B and Both. The cy cle will then re peat. TheLEDs above the [SE LECT] but ton light to in di cate thecur rent se lec tion.
Vol ume - Ad just the vol ume to the head set by ro tat ing the vol --ume con trol as re quired for a com fort able lis ten ing vol ume.
Por ta ble Sta tion Con nect
Se lect the au dio paths from the base sta tion’s four re ceiv ers that you wish to en able. The cor re spond ing LED above the se lectbut ton is on when the au dio path is en abled. If a beltpack userhas their por ta ble sta tion con nect path off at the base, that userwill no lon ger hear their sidetone and their au dio will not bepassed to any one. The user will still be able to hear ev ery one.The se lec tion is re tained in non-volatile mem ory, so it willcome-up where last left if the unit is power cy cled.
Al ways dis able un used au dio re ceive paths. This re duces thechances that ex ter nal RF noise can get onto the au dio busesvia an open re ceiver.
In ter com A and B
In ter com Se lect But ton - Press the [SE LECT] but ton tochoose be tween 2-wire or 4-wire in ter com sys tems. Thegreen LED will in di cate the cur rent mode of the in ter comchan nel. If the base sta tion is con nected to a 2-wire sys --tem, such as Audiocom (Telex), RTS TW or Clear-Com®, set the in ter com to 2-wire. If it is con nected to afour-wire sys tem, such as RTS Ma trix, set the in ter com to4-wire. It is also pos si ble to have in ter com A con nectedto a 2-wire sys tem and in ter com B con nected to a 4-wiresys tem or vice versa. The se lec tion is re tained innon-volatile mem ory, so it will come-up where last left ifthe unit is power cy cled.
In Level Con trol - Ad justs the au dio level of the wiredin ter com sys tem’s in put to the base sta tion.
Out Level Con trol - Ad justs the au dio level of the basesta tion’s out put to the wired in ter com sys tem.
If the base sta tion is used stand-alone, no wired in ter com sys --tem con nected, it must be set in the 4-wire mode. The 2-wiremode re quires a wired in ter com sys tem or ap pro pri ate load becon nected to the in ter com A or B XLRs. If not loaded, a large gain in crease will take place in the un load in ter com chan nelwhich may be high enough to pro duce a loud “howl ing”sound.
Aux il iary
Aux il iary In put Se lect But ton - Press the [SE LECT]but ton to turn on or off the aux il iary in put to the base sta --tion. The se lec tion is re tained in non-volatile mem ory, soit will come-up where last left if the unit is power cy cled.
In Level Con trol - Ad justs the au dio level of the wiredaux il iary sys tem’s in put to the base sta tion.
Out Level Con trol - Ad justs the au dio level of the basesta tion’s out put to the aux il iary XLR plug.
The aux il iary out put con nects only to in ter com B. It does notin ter face to in ter com A. The aux il iary in put may be switchedto B in ter com (de fault) or A and B in ter com. See Sec tion 5 for the lo ca tion of this in ter nally lo cated in put rout ing switch. The aux il iary out put is al ways avail able at the back panel out putXLR. It can not be switched on or off like the in put. Both thein put and out put are bal anced au dio ports. Aux il iary in put andout put au dio is global. See Sec tion 5 for more de tails.
7-2
TALK
MIC GAIN
TALK/O.M.VOLUME
SELECT
A
B
ON/O.M.
ON/OFF
IN
OUT
AUXILIARYINTERCOM B
2 WIRE
4 WIRE
SELECT
IN
OUT
2 WIRE
4 WIRE
SELECT
IN
OUT
INTERCOM APORTABLE STATION CONNECT
1 2 3 4
UP
DOWN
MENU
SET
RadioComä BTR-800
ClearScanTM
COPY
POWERPORTABLE STATION
CONNECT
INTERCOMA AND B
AUXILIARY
LOCALHEADSET
Base Sta tion - Rear Panel
![Page 37: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/37.jpg)
Dis play Con trast
The LCD’s (Liq uid Crys tal Dis play) con trast is set from thefac tory to a stan dard level. How ever it is pos si ble for the userto ad just the con trast if de sired. The con trast con trol is in ter --nal to the BTR-800 unit near the front panel. The cover mustbe re moved for ac cess to this con trol. Please see Fig ure 31 for the lo ca tion.
Fig ure 31LCD Con trast
7-3
V
D11
01
FRONT
BACK
R11
01
![Page 38: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/38.jpg)
BTR-800 Menu Structure
Main Screen Flowchart
The fol low ing con tains the base station menu struc ture andref er ences the pages in which fur ther de tail of that menu maybe found.
7-4
TelexRadioCom
Operating Screen - Pg. 7-5
Power-Up Screen - Pg. 7-5
Group/Channel Select Screen - Pg. 7-6
[MENU]
Group/Frequency Select Screen - Pg. 7-7
[MENU]
Frequency Edit Screen - Pg. 7-8
[MENU]
(User-Programmed Only)
[MENU]Action
[MENU]No Action
[MENU]+
[SET]
ClearScanTM
ClearScan Start-up/Search Screen - Pg. 7-9
[MENU]or
[SET]
ClearScan Result Screen - Pg. 7-9
[MENU]
SB10001SB10001
Group 25u
44
R1R1
OnOn
Ch ACh BTA A
2233T1T1
22
Group 25u
44
R1R1 Ch 01
OnOn
Ch 02Ch 03Ch 04
2233T1T1
22
Group 25u
44
R1R1 705.150
565.350554.250
707.850710.100715.300
2233T1T1
22
Group 25uFreq Edit
44
Ch1Ch1 705.150
565.350554.250
707.850710.100715.300
2233T1T1
22
Group 03AOK?=[SET]
Next
TM
C60001C60001
01 0502 060304 08
no tx
Other Spe cial Key Se quences:
Lock out. . . . . . . . . . . . . . . . . . . . . . . . 7-10Copy . . . . . . . . . . . . . . . . . . . . . . . . . 7-101st Use De fault . . . . . . . . . . . . . . . . . 7-10Fac tory De fault . . . . . . . . . . . . . . . . . . 7-10
NOTE: Pressing [MENU] within a screen af ter ac tionhas oc curred es capes from that ac tion and places theuser at the cur rent screen. Any ed it ing that had beendone since [SET] had been pressed is aborted.
Page
![Page 39: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/39.jpg)
Power-Up Screen
• This screen is dis played only on power up, first use de -fault and fac tory de fault.
• The 1st up per right cor ner num ber dis plays the base’s soft -ware re vi sion. The sin gle ver sion num ber in cre ments forchanges in op er a tional soft ware.
• The 2nd up per right cor ner num ber dis plays the base’schan nel map (fre quency plan) ver sion. The sin gle ver sionnum ber in cre ments for changes in the chan nel map.
• Once the power-up screen is dis played, it will change tothe op er at ing screen af ter a few sec onds.
Op er ating Screen
• Screen is dis played af ter power-up screen.
• Sys tem will re vert to this screen if no ac tiv ity is de tectedon the LCD dis play but tons af ter 3 min utes.
• Screen dis plays cur rent sta tus of the sys tem.
Beltpack Ac tiv ity Code Def i ni tions:
7-5
TelexRadioCom
SB10001SB10001
TMC60001C60001
Group 03A
T1T1 44
R1R1 tx
OnOn
OffCh BTA A
Operating Screen
2233T1T1
22
no
no tx = No Beltpack Trans mit Car rier De tectedOff = Re ceiver is not se lected on front panelCh A = Beltpack au dio is on Chan nel ACh B = Beltpack au dio is on Channel BCh A&B = Beltpack au dio is on Chan nel A and B (TR-825 only)TA A = Beltpack Chan nel B Talk Around Ac tiveTA B = Beltpack Chan nel A Talk Around Ac tiveTA A&B = Beltpack Chan nel A and B Talk Around Ac tive (TR-825 only)SA = Beltpack Stage An nounce Ac tive
NOTE: Older ver sions of BTR-800 soft ware do not sup port the de tec tion of TR-825 “Ch A&B”and “TA A&B” con trol tones.
Power-Up Screen
![Page 40: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/40.jpg)
Group / Chan nel Se lect
The Group/Chan nel se lect screen al lows the user to change the group and se lect from a pre-determined num ber of chan nelson each re ceiver.
• Hit [MENU] once to en ter the Group / Chan nel Se lectScreen from the op er at ing screen.
• Hit [SET] to en ter group edit. The group num ber will start flash ing. If [SET] is hit again with out hit ting the ar rows,the dis play will go to re ceive 01 chan nel edit. NOTE: Achan nel that does not have a fre quency set for it will havea dash to the right of it on the group/chan nel se lect screen.
• The [UP] / [DOWN] ar rows will change the group num -ber. Hit [SET] again to set the group that was flash ing.Now the group num ber will stop flash ing and R1’s chan -nel num ber will start to flash.
• The [UP] / [DOWN] ar rows will change the re ceive chan -nel num ber. Hit [SET] to set the chan nel that was se -lected. Now the sec ond chan nel num ber will start to flash. If [SET] is hit again with out hit ting the ar rows, the dis -play will go to the next chan nel num ber.
• Af ter the last re ceive chan nel is de cided upon, hit ting[SET] will set that chan nel in the unit and start you overat the be gin ning of the group/chan nel se lect screen withnoth ing flash ing.
• Hitting [MENU] will take you to the group/fre quency se -lect screen. NOTE: Hitting [MENU] af ter ac tiv ity has oc -curred within the screen will re turn to the group/chan nelse lect screen with noth ing flash ing. Any change that hadbeen done be fore the last [SET] was pressed will beaborted.
• Set ting two chan nels the same is not al lowed. If a chan nel is al ready set on the screen, the user no lon ger has thatchan nel as an op tion to set into one of the other re ceiv ers.
7-6
Group 14
T1T1 44
R1R1 Ch 01
OnOn
Ch 02Ch 03Ch 04
Group / Channel Select
2233T1T1
22
Group 14
T1T1 44
R1R1 Ch 01
OnOn
Ch 02Ch 03Ch 04
2233T1T1
22
Group 15
T1T1 44
R1R1 Ch 01
OnOn
Ch 02Ch 03Ch 04
2233T1T1
22
Group 15
T1T1 44
R1R1 Ch 05
OnOn
Ch 02Ch 03Ch 04
2233T1T1
22
[SET]
[UP] / [DOWN][SET]
[UP] / [DOWN][SET]
Group 15
T1T1 44
R1R1 Ch 05
OnOn
Ch 06Ch 07Ch 08
2233T1T1
22
Group 15
T1T1 44
R1R1 715.000
569.700568.500
716.700719.700721.600
2233T1T1
22
[MENU]
[UP] / [DOWN][SET] (Last Rx Changed)
END
![Page 41: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/41.jpg)
Group / Fre quency Se lect
The Group/Fre quency se lect screen al lows a user to set thegroup and se lect from a pre-determined num ber of fre quen cies on each re ceiver. Each fre quency dis played on the right half of the screen corresponds to a chan nel num ber in theGroup/Chan nel Screen.
• Press [MENU] twice to go to the Group / Fre quency Se -lect screen from the op er at ing screen. Hit [SET] to startthe group num ber flash ing.
• Press the [UP] / [DOWN] ar rows to change the groupnum ber. The fre quen cies listed will re flect what is cur -rently in that group. Hitting [SET] will se lect the groupand start the se lect ing of pre de ter mined fre quen cieswithin that group. The R1 fre quency will start flash ing.NOTE: The group num ber sets the trans mit fre quen ciesof fac tory de fined groups and these are not editable. Inuser-programmed groups these are editable from the fre -quency edit screen.
• Pressing the [UP] / [DOWN] ar rows will change the fre -quency of “R1” to the pre-defined fre quen cies avail able.Hitting [SET] will ac cept the change and start you ed it ing the next chan nel. If you had not hit the ar row keys whenthe fre quency was flash ing, but in stead hit [SET], youwould have skipped to the next fre quency to edit.
• Af ter the last re ceive fre quency is de cided upon, hit ting[SET] will save that last fre quency and start you over atthe be gin ning of the group/fre quency se lect screen withnoth ing flash ing.
• Pressing [MENU] will take you to the op er at ing screen ifthis is a fac tory-defined group. If within a user pro -grammed group, you will be taken to the fre quency editscreen. NOTE: Hitting [MENU] af ter ac tiv ity has oc -curred within the screen will re turn to the group/fre -quency edit screen with noth ing flash ing. Any change that had been done be fore the last [SET] was pressed will beaborted.
7-7
Group 15
T1T1 44
R1R1 715.000
569.700568.500
716.700719.700721.600
Group / Frequency Select
2233T1T1
22
Group 14
T1T1 44
R1R1 713.200
563.100561.700
716.100718.600 721.600
2233T1T1
22
Group 14
T1T1 44
R1R1
563.100561.700
2233T1T1
22
Group 14
T1T1 44
R1R1
563.100561.700
2233T1T1
22
[UP] / [DOWN]
[SET]
[UP] / [DOWN]
[SET] (Last Rx Changed)
[UP] / [DOWN]
[SET]
716.100718.600 721.600
704.200
704.700708.300 709.500
704.200
Group 14
T1T1 44
R1R1
OnOn
2233T1T1
22
[MENU]
Ch A Ch B
no tx
END
no tx
![Page 42: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/42.jpg)
Fre quency Edit(User-Programmed Groups Only)
This menu only oc curs for user-programmable groups or when copy ing to a user-programable group. The Fre quency Editscreen al lows the user to set the group trans mit fre quen ciesand re ceive chan nel fre quen cies of a user-programmablegroup.
• Press [MENU] three times to go to the fre quency se lectscreen from the op er at ing screen. Press [SET] to start thegroup num ber flash ing. This screen al lows the user to setthe group and fre quen cies of user-programmed groupsonly.
• Press the [UP] / [DOWN] ar rows to change the groupnum ber. The fre quen cies listed will re flect what is cur -rently in that group. Dashes will be dis played in any slots that are not de fined yet. Pressing [SET] will se lect thegroup and start the se lect ing of fre quen cies within thatgroup. The T1 fre quency will start flash ing.
• Pressing the [UP] / [DOWN] ar rows will change the fre -quency of “T1” in 25kHz steps. Pressing [SET] will ac -cept the change and start you ed it ing T2. If you had nothit the ar row keys when the fre quency was flash ing, butin stead press [SET], you would have skipped to the nextfre quency to edit.
• Af ter ed it ing the trans mit and the re ceive chan nel fre -quen cies, press ing [SET] will save that last fre quency and send you over to the be gin ning of the group/fre quencyselect screen with noth ing flash ing. NOTE: Once the end of the dis played chan nel list is reached, the last dis playedchan nel lo ca tion will scroll to al low the user to edit the re -main ing chan nels.
• Af ter ac tion has oc curred in the fre quency edit screen hit -ting [MENU] will take you one menu back to thegroup/fre quency se lect screen so that the user may seewhat fre quen cies the base re ceiv ers are now on. If no ac -tion had oc curred, then pressing [MENU] will take you to the op er at ing screen. NOTE: Be sides a group change,any ed it ing that oc curs within this screen to fre quen ciesDOES NOT take ef fect un til the user ex its the screen viaset ting the last chan nel or press ing [MENU].
7-8
Group 25uFreq Edit
705.150
565.350554.250
707.850710.100715.300
Group 27uFreq Edit
705.150
567.800554.250
707.850710.100 715.300
Group 27uFreq Edit
567.800556.725
Group 27uFreq Edit
569.350556.700
[UP] / [DOWN]
[SET]
[UP] / [DOWN][SET]
[UP] / [DOWN]
[SET]
707.850710.100 715.300
705.150
720.550721.350 721.900
718.550
Group 27u
569.350556.700
[SET] or [MENU](Last Ch Changed)
710.550714.225 716.800
705.950
END
Fre quency Edit(User-Programmed Groups Only)
![Page 43: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/43.jpg)
ClearScan™
ClearScan™ per forms a fre quency scan of the fac tory-defined and any set-up user-programmable groups in or der to find thegroup with the high est num ber of clear re ceive chan nels. Af ter about 20-30 sec onds, the group with the high est num ber ofclear re ceive chan nels will be dis played. The next best groupand so forth may be ac cessed with the [DOWN] and [UP]arrow but tons.
• Press and hold [MENU] + [SET] for three sec onds to en -ter ClearScan™. The base sta tion will now start search ing all groups for the ones with the great est num ber of re -
ceiver chan nels clear of in ter fer ence.
• ClearScan™ will dis play the group that has the most in -ter fer ence free re ceive chan nels. These clear chan nels aredis played on the right half of the screen. Press [SET] toplace the base sta tion on this group and re turn to the op er -at ing screen. The first four re ceive chan nels dis playedwill be the ones set for the group. The [UP] / [DOWN]but tons may be used to se lect the next best group and soforth.
To achieve the best re sults quickly when us ing ClearScan,please com plete the fol low ing for set ting up a sin gle BTR-800 sys tem:
• Turn off all wire less in ter com and wire less mi cro phoneequip ment.
• Turn on all wire less mi cro phones and wire less mon i tortrans mit ters. Make sure that this equip ment is dis trib utedat least 3 to 5 feet apart from each other to minimize anyfre quency intermodulation ef fects.
• Turn on one TR-700/800/825 and per form the ClearScanfunc tion as descibed on page 7-18 and 7-29 of this man -ual.
• When the first re sult is dis played on the TR, write thisdown along with the next 6 or 7 re sults. This num ber rep -re sents the spe cific BTR trans mit ter that should pro videthe best re sults for op er a tion. This is re ferred to as the"Group".
• Once you have re corded the first 6 or 7 re sults from theTR, turn off the TR unit.
• Turn on the BTR-700 OR BTR-800 and per form theClearScan func tion as de scribed above. The re sults of theBTR will pro vide the num ber of "Chan nels" or TR trans -mit ters that can op er ate in a given group.
• Since you have al ready es tab lished the best BTR Group(base sta tion trans mit fre quency) to op er ate on, se lec tionof the op er at ing chan nels is now much eas ier.
• Sim ply match the num ber of TRs to op er ate on your sys -tem with the first and best "Group" num ber that you havere corded.
• When you have scrolled to the ap pro pri ate Group num ber that dis plays the num ber of beltpacks to be used on thesys tem, simpley press [SET] on the BTR to place the BTR on the se lected Group and Chan nel.
• Fi nally, go back to the TRs and pro gram to the ap pro pri -ate Group and Chan nel.
7-9
ClearScan™
Scan
Group 03AOK?=[SET]
Next
01 0502 060304 08
Group 04b 01 05OK?=[SET] Prev
Next
060304 08
[DOWN]
[SET]
Group 04b
T1T1 44
R1R1
OnOn
2233T1T1
22
Ch ACh B TA A
no tx
END
![Page 44: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/44.jpg)
Spe cial Key Se quences
Lock out
• Press [UP]+[DOWN] for 3 sec onds to lock or un lock thebase sta tion. Pressing [MENU] will still func tion to viewscreens, but [SET] will no lon ger start any ed it ing. ClearScan™ , First use, Fac tory de fault are no lon ger ac -ces si ble. The in ter com chan nel A and B front panel2-wire/4-wire se lec tion is also locked into place. A pad -lock icon will be dis played on the sec ond line of the dis -play to the far left as an in di ca tion that the base sta tion islocked out.
Copy
• Press [SET]+[DOWN] for 3 sec onds to copy any cur -rently dis played group to a user-programmable group. Copy can be done from the group/chan nel se lect,group/fre quency se lect or fre quency edit screen. Oncepressed, the words, “Copy to” are dis played on the screenwith the first empty user-programmable group flash ing. If all the user-programmed groups were full, than the firstprogramable group is dis played. The [UP] or [DOWN]but tons may be used to se lect a different user-programmable group if de sired. Pressing [SET] pastes fre quen cies/chan -nels to the group and take the user to the fre quency editscreen with “T1” flash ing.
1st Use De fault
• Press [MENU] while turn ing on the base sta tion to en terthe 1st use de fault setup screen. This places the unit ongroup 01A with the four re ceiv ers set to chan nels 1- 4 ofthe group. Any user-programmed fre quen cies that had been en tered pre vi ously are re tained. If lock out hadbeen ac ti vated, the beltpack co mes up where it was lastleft re gard less of [MENU] be ing pressed on power-up.
Fac tory De fault
• Pressing all four but tons [MENU]+[SET]+[UP]+[DOWN]at the same time for 3 sec onds places the unit on group01A with the four re ceiv ers set to chan nels 1 – 4 of thatgroup. This is just like base sta tion 1st use de fault, ex ceptthat all user-programmed fre quen cies that had been en -tered pre vi ously are erased. This func tion may take sev -eral sec onds. If lock out had been ac ti vated, the beltpackco mes up where it was last left re gard less of these fourkeys be ing pressed.
7-10
![Page 45: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/45.jpg)
Beltpack Op er a tion
On/Off and Vol ume Con trolTurn the beltpack power on by ro tat ing the knob CW. Ad justthe vol ume to the head set by ro tat ing the vol ume con trol as re --quired for a com fort able lis ten ing vol ume.
Bat tery CheckWhen the beltpack power is turned on by ro tat ing the knob,the BAT/OM LED will flash once if the bat tery is good. If theLED stays on, the bat tery is low. If the LED does not flash,the bat tery is dead.
Talk But tonPress the talk but ton to en able the au dio path from the head setmi cro phone. The TALK/OM LED will turn red when au dio isen abled. A quick press and re lease latches the talk func tionun less latch ing has been disabled. Holding the but ton for over½ a sec ond will cause the au dio path to be en abled only for aslong as the but ton is held. If the talk func tion is latched on,press ing the talk but ton again will turn it off. See the “TalkBut ton Latching/Non-Latching” instructions in Sec tion 7 tolearn how to en able/dis able latch ing of the talk but ton.
Mi cro phone GainAd justs the head set’s mi cro phone gain. Ad just so the TALK/OM LED flashes red at the be gin ning of most words at nor mal speech lev els. If the in put is too large, the LED will be red dur ing thecom plete word at nor mal speech level. The peak-responding au --dio lim iter in the beltpack is very tol er ant of high in put au dio lev --els. Even when the mi cro phone gain is max i mized, and head setvol ume re duced to make up for the louder au dio, the au dio willstill sound good and not clipped.
Au dio Chan nel Se lect But ton Se lects the in ter com sys tem to which the head set is con nected. The LED near the chan nel but ton in di cates the cur rent se lec --tion. See the “Au dio Chan nel A/B En able/Dis able” in struc --tions in Sec tion 7 to learn how to en able only chan nel A,chan nel B, or both.
Stage An nounce (SA)When pressed the au dio from the beltpack is routed di rectly to the stage an nounce con nec tor on the back of the base sta tion. The base sta tion’s SA re lay is also closed. The beltpacksidetone is lost as an in di ca tion that stage an nounce is ac ti --vated. The other beltpacks and wired us ers do not hear thisbeltpacks au dio when SA is pressed. The but ton isnon-latching and ac tivates the nearby red LED when pressed.See the “Stage An nounce En able/Dis able” instructions in Sec --tion 7 to learn how to en able/dis able the SA but ton.
Wire less Talk Around (WTA)
When pressed, the au dio from the beltpack is dis con nectedfrom the wired in ter com, aux il iary in put/out put and the basesta tion’s lo cal head set. Other beltpack us ers, on that au diochan nel, can hear the user as nor mal. The but ton ac tivates thenearby red LED as well as the ap pro pri ate talk LED whenpressed. See the “Wire less Talk Around En able/Dis able” in --struc tions in Sec tion 7 to learn how to en able/dis able the WTA but ton as well as other fea tures.
7-11
VOL
OFFSA
WTA
Telex R
A B
CHANNEL
BAT/OM TALK
TALK
ME
NU
SE
T
MIC PTTX
PTTALK
WIRELESSTALK AROUND (WTA)
STAGE ANNOUNCE(SA)
AUDIO CHANNELSELECT BUTTON
TALKBUTTON
MICROPHONEGAIN
BATTERY CHECK
TR-800
VOL
OFF
SA
WTA
Telex R
TALK
VOL
OFF
TALK
A B
BAT/OM
WIRELESS TALK AROUND (WTA)
ON/OFF andVOLUME
CONTROL
ON/OFF andVOLUME
CONTROL
STAGE ANNOUNCE (SA)
TALKBUTTON
TALKBUTTON
BATTERY CHECK
TR-825
ON/OFF andVOLUME
CONTROL
Fig ure 32TR-800 and TR-825 Top and Rear Panel
![Page 46: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/46.jpg)
TR-800 Menu Struc ture
Beltpack Menu Struc ture
7-12
[MENU]
S10001
c60001
03A 01
Power-Up Screen - Pg. 7-13
Group/Channel Screen - Pg. 7-14
GP CH
[MENU]
704.200
Transmit Screen - Pg. 7-15
TX
[MENU]
566.200R1
[MENU]
570.300R2
Receive 1 Screen - Pg. 7-16
Receive 2 Screen - Pg. 7-17
Clr ScnGP
04A ScnGP
[MENU]+
[SET]ClearScan Search Screen - Pg. 7-18
ClearScan Result Screen - Pg. 7-18
[MENU]or
[SET]
The fol low ing con tains the main beltpack menu struc ture and ref er --ences the pages in which fur ther de tail of that menu may be found.
All beltpack fea tures and spe cial key se quences can only be donefrom the group/channel screen.
Beltpack Fea ture En able/Dis able Menus:
Stage An nounce (SA) En able/Dis able . . . . . . . . . 7-19Wire less Talk Around (WTA) En able/Dis able . . . 7-19Au dio Chan nel A/B Enable/Dis able. . . . . . . . . . . 7-20Talk But ton Latching/Non-Latching. . . . . . . . . . . 7-20
Other Spe cial Key Se quences:
Lock out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-211st Use De fault . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-21Fac tory De fault . . . . . . . . . . . . . . . . . . . . . . . . . . 7-21
NOTE: Pressing [MENU] within a screen af ter ac tion has oc curred es capesfrom that ac tion and places the user at the cur rent screen. Any ed it ing thathad been done since [SET] had been pressed is aborted.
Page
Page
![Page 47: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/47.jpg)
TR-800 Menu Struc ture
Power-Up Screens
• The first screens dis played when the beltpack is pow eredup are the soft ware and chan nel map ver sion screens.
• The 1st screen dis played in di cates the beltpack’s soft warever sion num ber. It is dis played for about one sec ond.
• The 2nd screen dis played in di cates the beltpack’s chan nel map (fre quency plan) ver sion num ber. It is dis played forabout one sec ond.
• The fi nal screen dis played is the group/chan nel screen
7-13
END
S10001
c60001
03A 01GP CH
Power-Up Screens
![Page 48: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/48.jpg)
TR-800 Menu Struc ture
Group / Chan nel Screen
The Group/Chan nel screen al lows the user to change thegroup and se lect from a pre-determined num ber of trans mitchan nels.
• The screen dis played af ter the beltpack pow er-up screens.
• Press [SET] to edit the chan nel num ber. The chan nelnum ber will start flash ing.
• Use the [UP]/[DOWN] ar row but tons to change the chan -nel num ber.
• Press [SET] to place the beltpack on the chan nel se lected. Once set is pressed, the beltpack trans mit ter will move tothat fre quency and noth ing will be flash ing. Now press[SET] twice to en ter group edit.
• Use the [UP]/[DOWN] ar row but tons to change the group num ber.
• Press [SET] to place the beltpack on the group se lected. Once set is pressed, the unit re turns to the group/chan neldis play with noth ing flash ing.
• Pressing [SET] once more will start the ed it ing se quenceover again. Pressing [MENU] dur ing the group edit willend ed it ing and send the user back at the group/chan nelscreen with out any changes. This ap plies to chan nel ed it -ing too.
7-14
03A 01CH
03A 01GP
03A 01CH
03A 01GP
CH03A 02GP
CH03A 02GP
CH05b 02GP
CH05b 02GP
[SET]
[UP]/[DOWN]
[SET]then [SET] twice more
[UP]/[DOWN]
[SET]
END
Group / Chan nel Screen
![Page 49: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/49.jpg)
TR-800 Menu Struc ture
Trans mit Screen
The Transmit screen al lows the user to set the beltpack trans --mit fre quency. Fac tory-defined groups will al low only a setnum ber of pre-defined fre quen cies to be se lected. User-programmable groups will al low the user to change thefre quency in 25kHz steps.
• Press [MENU] once from the group/chan nel screen to ar -rive at the trans mit fre quency screen.
• Press [SET] to edit the fre quency. The num ber will startflash ing.
• Use the [UP]/[DOWN] ar row but tons to change the fre -quency.
• Press [SET] to place the beltpack on the fre quency se -lected. If set is held down, dur ing that time thegroup/chan nel is dis played so the user is aware of whattrans mit chan nel the unit has been placed. Once set is re -leased, the unit re turns to the trans mit fre quency screenwith noth ing flash ing.
• Pressing [SET] once more will start the ed it ing se quenceover again. Pressing [MENU] dur ing trans mit fre quencyedit will end ed it ing and send the user back to the trans mit screen with out any changes.
7-15
[SET]
03A 03GP CH
704.700TX
706.500TX
[UP]/[DOWN]
[SET] IS HELD DOWN
[SET] IS RELEASED
706.500TX
END
704.700TX
Trans mit Screen
![Page 50: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/50.jpg)
TR-800 Menu Struc ture
Re ceive 1 Screen
The Receive 1 screen al lows the user to set the beltpack re --ceive 1 fre quency. This cor re sponds to the base sta tion’s trans --mit 1 fre quency. In fac tory-defined groups re ceive 1 is notchange able. User-programable groups will al low the user tochange the fre quency in 25 KHz steps.
• Press [MENU] twice from the group/chan nel screen to ar -rive at the re ceive 1 fre quency screen.
• (User-Programmable Groups Only) Press [SET] to editthe fre quency. The num ber will start flash ing. Fac -tory-defined groups can’t be changed; so press ing set willdo noth ing at this screen. User-programmed groups willstart flash ing and al low the user to change the fre quencyin 25kHz steps.
• (User-Programmable Groups Only) Use the[UP]/[DOWN] ar row but tons to change the fre quency.
• (User-Programmable Groups Only) Press [SET] to placethe beltpack on the fre quency se lected. If set is helddown, dur ing that time the group is dis played so the useris aware of what group the unit has been placed. Once setis re leased, the unit re turns to the re ceive 1 fre quencyscreen with noth ing flash ing.
• (User-Programmable Groups Only) Pressing [SET] oncemore will start the ed it ing se quence over again. Pressing[MENU] dur ing re ceive 1 fre quency edit will end ed it ingand send the user back to the re ceive 1 screen with out any changes.
7-16
554.250
[SET]
554.250R1
R1
566.750R1
[SET] IS HELD DOWN
27uGP
[SET] IS RELEASED
END
566.750R1
[UP] / [DOWN]
Re ceive 1 Screen
![Page 51: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/51.jpg)
TR-800 Menu Struc ture
Re ceive 2 Screen
The Re ceive 2 screen al lows the user to set the beltpack re --ceive 2 fre quency. This cor re sponds to the base sta tion’s trans --mit 2 fre quency. In fac tory-defined groups re ceive 1 is notchange able. User-programable groups will al low the user tochange the fre quency in 25 KHz steps.
• Press [MENU] three times from the group/chan nel screen
to ar rive at the re ceive 2 fre quency screen.
• (User-Programmable Groups Only) Press [SET] to editthe fre quency. The num ber will start flash ing. Fac -tory-defined groups can’t be changed, so press ing set willdo noth ing at this screen. User-programmed groups willstart flash ing and al low the user to change the fre quencyin 25kHz steps.
• (User-Programmable Groups Only) Use the[UP]/[DOWN] ar row but tons to change the fre quency.
• (User-Programmable Groups Only) Press [SET] to placethe beltpack on the fre quency se lected. If set is helddown, dur ing that time the group is dis played so the useris aware of what group the unit has been placed. Once set is re leased, the unit re turns to the re ceive 2 fre quencyscreen with noth ing flash ing.
• (User-Programmable Groups Only) Pressing [SET] oncemore will start the ed it ing se quence over again. Pressing[MENU] dur ing re ceive 2 fre quency edit will end ed it ingand send the user back to the re ceive 2 screen with out any changes.
7-17
565.350
[SET]
565.350R2
R2
567.850
[SET] IS HELD DOWN
27uGP
[SET] IS RELEASED
END
567.850
[UP] / [DOWN]
R2
R2
Re ceive 2 Screen
![Page 52: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/52.jpg)
TR-800 Menu Struc ture
ClearScan™
ClearScanTM per forms a fre quency scan of the fac tory-definedand any set-up user-programmable groups in or der to find theclear est group. Af ter about 30 sec onds, the clear est group isdis played. A group is de fined by re ceive 1 and 2 fre quen cies.The next best group and so forth may be ac cessed with the[DOWN] and [UP] ar row but tons.
• Press and hold [MENU] + [SET] for three sec onds to en -ter ClearScanTM. The beltpack will now start search ing forthe clear est groups. The group sym bol will flash in di cat -ing the beltpack is scan ning for clear groups.
• ClearScanTM will scan all groups. It will then dis play the1st group it came to that had the clear est re ceive chan nels. The [UP] / [DOWN] but tons may be used to se lect thenext best group and so forth. Hit [SET] to place thebeltpack on this group and re turn to the group/chan nelscreen.
7-18
END
04b 01GP CH
Clr ScnGP
04b ScnGP
[SET]
ClearScan™
![Page 53: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/53.jpg)
TR-800 Menu Struc ture
Stage An nounce En able/Dis able
• Press and hold [SET] then press the [SA] but ton to showthe SA en able/dis able screen. The cur rent set ting of thefea ture is dis played on the LCD.
• While con tin u ing to hold [SET] press [SA] again to tog -gle the dis play from ON to OFF or back. Re lease the[SET] but ton to ac cept the cur rent dis played set ting andre turn to the Group/Chan nel screen.
Wire less Talk Around En able/Dis able
• Press and hold [SET] then press the [WTA] but ton toshow the WTA en able/dis able screen. The cur rent set tingof the fea ture is dis played on the LCD.
• While con tin u ing to hold [SET] press [SA] again to cy clethe dis play from on, off, then L on (latch on). Re lease the[SET] but ton to ac cept the cur rent dis played set ting andre turn to the Group/Chan nel screen.
7-19
END
03A 01GP CH
SA on
SA oFF
RELEASE [SET]
HOLD [SET] AND PRESS [SA]
CONTINUE TO HOLD [SET]AND PRESS [SA] AGAIN
END
03A 01GP CH
tA on
HOLD [SET] AND PRESS [WTA]
CONTINUE TO HOLD [SET]AND PRESS [WTA] AGAIN
CONTINUE TO HOLD [SET]AND PRESS [WTA] AGAIN
tA oFF
tA Lon
RELEASE [SET]
![Page 54: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/54.jpg)
TR-800 Menu Struc ture
Au dio Chan nel A or B Dis able/En able
• Press and hold [SET] then press the [CHAN] but ton toshow the chan nel en able/dis able screen. The cur rent set -ting of the fea ture is dis played on the LCD.
• While con tin u ing to hold [SET], press the [CHAN] but ton again to move to the next op tion, only chan nel B on.
• As you con tinue to hold [SET], press the [CHAN] but tononce more to move to the next op tion, only chan nel A on. If the chan nel but ton was hit once more, the user wouldstart over at the AB ON screen.
• Re lease the [SET] but ton to ac cept the cur rent dis playedset ting and re turn to the Group/Chan nel screen.
Talk But ton Latch on/Latch off
• Press and hold [SET] then press the [TALK] but ton toshow the Talk But ton Latch/Non-Latching screen Thecur rent set ting of the fea ture is dis played on the LCD dis -play.
• While con tin u ing to hold [SET] press [TALK] again totog gle the dis play from on to off or back. Re lease the[SET] but ton to ac cept the cur rent dis played set ting andre turn to the Group/Chan nel screen.
7-20
b on
Disabling Audio Channel A
Ab on
A on
HOLD [SET] AND PRESS [CHAN]
CONTINUE TO HOLD [SET]AND PRESS [CHAN] AGAIN
END
03A 01GP CH
RELEASE [SET]
CONTINUE TO HOLD [SET]AND PRESS [CHAN] AGAIN
l on
HOLD [SET] AND PRESS [TALK]
END
03A 01GP CH
RELEASE [SET]
CONTINUE TO HOLD [SET]AND PRESS [TALK] AGAIN
t
l oFFt
![Page 55: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/55.jpg)
TR-800 Menu Struc ture
Spe cial Key Se quences
Lock out
• Press [UP]+[DOWN] for 3 sec onds to lock or un lock thebeltpack. The words “Loc on” will be dis played when thefea ture is ac ti vated, “Loc oFF” will be dis played when the beltpack is un locked. Pressing [MENU] will still func tionto view screens, but [SET] will no lon ger start any ed it -ing. ClearScan™, First use, Fac tory de fault and Fea tureen able/dis able are no lon ger ac ces si ble.
1st Use De fault
• Press [MENU] while turn ing on the beltpack to en ter the1st use de fault setup screen. This places the unit on group01A with chan nel 01 flash ing. Any user-programmedfre quen cies that had been en tered pre vi ously are re -tained. The beltpacks must now be set to dif fer ent trans -mit chan nels us ing the [UP]/[DOWN] but tons. Then[SET] is hit to place the units on those chan nels. If lock -out had been ac ti vated, the beltpack co mes up where itwas last left re gard less of [MENU] be ing pressed onpower-up.
Fac tory De fault
• Pressing all four but tons [MENU]+[SET]+[UP]+[DOWN] at the same time for three sec onds places the unit ongroup 01A with chan nel 01 flash ing, just like beltpack 1st
use de fault, ex cept the all user-programmed fre quen cies that had been en tered pre vi ously are erased. Af ter thebut tons are re leased, it still may take sev eral sec onds forthe beltpack to re set. The beltpacks must now be set todif fer ent trans mit chan nels us ing the [UP]/[DOWN] but -tons. Then [SET] is hit to place the units on those chan -nels. If lock out had been ac ti vated, the beltpack co mes up where it was last left re gard less of these four keys be ingpressed.
7-21
![Page 56: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/56.jpg)
TR-825 Menu Struc ture
Beltpack Menu Struc ture
7-22
The fol low ing con tains the main beltpack menu struc ture and ref er --ences the pages in which fur ther de tail of that menu may be found.
All beltpack fea tures and spe cial key se quences can only be donefrom the group/channel screen.
Beltpack Fea ture En able/Dis able Menus:
Au dio Out put . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-28Stage An nounce (SA) . . . . . . . . . . . . . . . . . . . . . . 7-30Wire less Talk Around (WTA). . . . . . . . . . . . . . . . 7-31Au dio Chan nel A . . . . . . . . . . . . . . . . . . . . . . . . . 7-32Au dio Chan nel B . . . . . . . . . . . . . . . . . . . . . . . . . 7-33
Other Spe cial Key Se quences:
Lock out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-341st Use De fault . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-34Fac tory De fault . . . . . . . . . . . . . . . . . . . . . . . . . . 7-34
NOTE: Pressing [MENU] within a screen af ter ac tion has oc curred es capesfrom that ac tion and places the user at the cur rent screen. Any ed it ing thathad been done since [SET] had been pressed is aborted.
Page
Page
[MENU]
S30001
c60001
03A 01
Power-Up Screen - Pg. 7-23
Group/Channel Screen - Pg. 7-24
GP CH
[MENU]
704.200
Transmit Screen - Pg. 7-25
TX
[MENU]
566.200R1
[MENU]
570.300R2
Receive 1 Screen - Pg. 7-26
Receive 2 Screen - Pg. 7-27
Clr ScnGP
04A ScnGP
[MENU]+
[SET]ClearScan Search Screen - Pg. 7-29
ClearScan Result Screen - Pg. 7-29
[MENU]or
[SET]
[MENU]
Ab Add
Audio Output - Pg. 7-28
![Page 57: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/57.jpg)
TR-825 Menu Struc ture
Power-Up Screens
• The first screens dis played when the beltpack is pow eredup are the soft ware and chan nel map ver sion screens.
• The 1st screen dis played in di cates the beltpack’s soft warever sion num ber. It is dis played for about one sec ond.
• The 2nd screen dis played in di cates the beltpack’s chan nel map (fre quency plan) ver sion num ber. It is dis played forabout one sec ond. The op er at ing screen is then dis played.
• The fi nal screen dis played is the group/chan nel screen
7-23
END
S30001
c60001
03A 01GP CH
Power-Up Screens
![Page 58: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/58.jpg)
TR-825 Menu Struc ture
Group / Chan nel Screen
The Group/Chan nel screen al lows the user to change thegroup and se lect from a pre-determined num ber of trans mitchan nels.
• The screen dis played af ter the beltpack powered-upscreens.
• Press [SET] to edit the chan nel num ber. The chan nelnum ber will start flash ing.
• Use the [UP]/[DOWN] ar row but tons to change the chan -nel num ber.
• Press [SET] to place the beltpack on the chan nel se lected. Once set is pressed, the beltpack trans mit ter will move tothat fre quency and noth ing will be flash ing. Now press[SET] twice to en ter group edit.
• Use the [UP]/[DOWN] ar row but tons to change the group num ber.
• Press [SET] to place the beltpack on the group se lected. Once set is pressed, the unit re turns to the group/chan neldis play with noth ing flash ing.
• Pressing [SET] once more will start the ed it ing se quenceover again. Pressing [MENU] dur ing the group edit willend ed it ing and send the user back at the group/chan nelscreen with out any changes. This ap plies to chan nel ed it -ing also.
7-24
03A 01CH
03A 01GP
03A 01CH
03A 01GP
CH03A 02GP
CH03A 02GP
CH05b 02GP
CH05b 02GP
[SET]
[UP]/[DOWN]
[SET]
[UP]/[DOWN]
[SET]
END
Group / Chan nel Screen
![Page 59: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/59.jpg)
TR-825 Menu Struc ture
Trans mit Screen
The Trans mit screen al lows the user to set the beltpack trans --mit fre quency. Fac tory-defined groups will al low only a setnum ber of pre-defined fre quen cies to be se lected. User-programmable groups will al low the user to change thefre quency in 25kHz steps.
• Press [MENU] once from the group/chan nel screen to ar -rive at the trans mit fre quency screen.
• Press [SET] to edit the fre quency. The num ber will startflash ing. Fac tory-defined groups will al low only a setnum ber of pre-defined fre quen cies to be se lected.User-programmable groups will al low the user to changethe fre quency in 25kHz steps.
• Use the [UP]/[DOWN] ar row but tons to change the fre -quency.
• Press [SET] to place the beltpack on the fre quency se -lected. If set is held down, dur ing that time thegroup/chan nel is dis played so the user is aware of whattrans mit chan nel the unit has been placed. Once set is re -leased, the unit re turns to the trans mit fre quency screenwith noth ing flash ing.
• Pressing [SET] once more will start the ed it ing se quenceover again. Pressing [MENU] dur ing trans mit fre quencyedit will end ed it ing and send the user back to the trans mit screen with out any changes.
7-25
[SET]
03A 03GP CH
704.700TX
706.500TX
[UP]/[DOWN]
[SET] IS HELD DOWN
[SET] IS RELEASED
706.500TX
END
704.700TX
Trans mit Screen
![Page 60: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/60.jpg)
TR-825 Menu Struc ture
Re ceive 1 Screen
The Re ceive 1 screen al lows the user to set the beltpack re --ceiver 1 fre quency. This cor re sponds to the base sta tion’strans mit 1 fre quency. In fac tory-defined groups re ceiver 1 isnot change able. User-programmable groups will al low theuser to change the fre quency in 25kHz steps.
• Press [MENU] twice from the group/chan nel screen to ar -rive at the re ceive 1 fre quency screen.
• (User-Programmable Groups Only) Press [SET] to editthe fre quency. The num ber will start flash ing. Fac -tory-defined groups can’t be changed; so press ing set willdo noth ing at this screen. User-programmed groups willstart flash ing and al low the user to change the fre quencyin 25kHz steps.
• (User-Programmable Groups Only) Use the[UP]/[DOWN] ar row but tons to change the fre quency.
• (User-Programmable Groups Only) Press [SET] to placethe beltpack on the fre quency se lected. If set is helddown, dur ing that time the group is dis played so the useris aware of what group the unit has been placed. Once setis re leased, the unit re turns to the re ceive 1 fre quencyscreen with noth ing flash ing.
• (User-Programmable Groups Only) Pressing [SET] oncemore will start the ed it ing se quence over again. Pressing[MENU] dur ing re ceive 1 fre quency edit will end ed it ingand send the user back to the re ceive 1 screen with out any changes.
7-26
554.250
[SET]
554.250R1
R1
566.750R1
[SET] IS HELD DOWN
27uGP
[SET] IS RELEASED
END
566.750R1
[UP] / [DOWN]
Re ceive 1 Screen
![Page 61: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/61.jpg)
TR-825 Menu Struc ture
Re ceive 2 Screen
The Re ceive 2 screen al lows the user to set the beltpack re --ceive 2 fre quency. This cor re sponds to the base sta tion’s trans --mit 2 fre quency. In fac tory-defined groups re ceiver 2 is notchange able. User-programable groups will al low the user tochange the fre quency in 25kHz steps.
• Press [MENU] three times from the group/chan nel screen
to ar rive at the re ceive 2 fre quency screen.
• (User-Programmable Groups Only) Press [SET] to editthe fre quency. The num ber will start flash ing. Fac -tory-defined groups can’t be changed, so press ing set willdo noth ing at this screen. User-programmed groups willstart flash ing and al low the user to change the fre quencyin 25kHz steps.
• (User-Programmable Groups Only) Use the[UP]/[DOWN] ar row but tons to change the fre quency.
• (User-Programmable Groups Only) Press [SET] to placethe beltpack on the fre quency se lected. If set is helddown, dur ing that time the group is dis played so the useris aware of what group the unit has been placed. Once set is re leased, the unit re turns to the re ceive 2 fre quencyscreen with noth ing flash ing.
• (User-Programmable Groups Only) Pressing [SET] oncemore will start the ed it ing se quence over again. Pressing[MENU] dur ing re ceive 2 fre quency edit will end ed it ingand send the user back to the re ceive 2 screen with out any changes.
7-27
565.350
[SET]
565.350R2
R2
567.850
[SET] IS HELD DOWN
27uGP
[SET] IS RELEASED
END
567.850
[UP] / [DOWN]
R2
R2
Re ceive 2 Screen
![Page 62: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/62.jpg)
TR-825 Menu Struc ture
Au dio Out put
The Au dio Out put screen al lows the user to set the au dio out --put to Mono (Add) or Ste reo (SEP). This op tion only ap pliesto beltpacks with 5 pin head set con nec tors. Sin gle sided 5-pinhead sets will only re ceive A or B Au dio de pend ing on how the head set is wired. Sin gle sided 5-pin head sets must set the au --dio out put to "Ab SEP". The au dio output op tion set ting doesnoth ing with a 4 pin head set con nec tor.
• Press [MENU] four times from the group/chan nel screento ar rive at the au dio out put screen
• Press [SET] to change the set ting. The op tion will start toflash.
• Use the [UP]/[DOWN] ar row but tons to change the au dio out put op tion.
• Press [SET] to end ed it ing and ac cept the set ting.
7-28
END
Ab SEP
[SET]
[SET]
Ab SEP
Ab Add
[UP]/[DOWN]]
Ab Add
Au dio Output
![Page 63: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/63.jpg)
TR-825 Menu Struc ture
ClearScanTM
ClearScanTM per forms a fre quency scan of the fac tory-definedand any set-up user-programmable groups in or der to find theclear est group. Af ter about 30 sec onds, the clear est group isdis played. A group is de fined by re ceive 1 and 2 fre quen cies.The next best group and so forth may be ac cessed with the[DOWN] and [UP] ar row but tons.
• Press and hold [MENU] + [SET] for three sec onds to en -ter ClearScanTM. The beltpack will now start search ing forthe clear est groups. The group sym bol will flash in di cat -ing the beltpack is scan ning for clear groups.
• ClearScanTM will scan all groups. It will then dis play the1st group it came to that had the clear est re ceive chan nels(low est RSSI lev els on the two fre quen cies). The [UP] /[DOWN] but tons may be used to se lect the next bestgroup and so forth. Press [SET] to place the beltpack onthis group and re turn to the group/chan nel screen.
7-29
END
04b 01GP CH
Clr ScnGP
04b ScnGP
[SET]
ClearScan™
![Page 64: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/64.jpg)
TR-825 Menu Struc ture
Stage An nounce En able/Disable
• Press and hold [SET] then press the [SA] but ton to showthe SA en able/dis able screen. The cur rent set ting of thefea ture is dis played on the LCD dis play.
• While con tin u ing to hold [SET] press [SA] again to tog -gle the dis play from ON to OFF or back. Re lease the[SET] but ton to ac cept the cur rent dis played set ting andre turn to the Group/Chan nel screen.
• NOTE: When SA is en abled and pressed, what ever is on;A talk, B talk, or both, goes out. No au dio chan nels showac tive when SA is pressed.
7-30
END
03A 01GP CH
SA on
SA oFF
RELEASE [SET]
CONTINUE TO HOLD [SET]AND PRESS [SA]
![Page 65: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/65.jpg)
TR-825 Menu Struc ture
Wire less Talk Around
• Press and hold [SET] then press the [WTA] but ton toshow the WTA menu screen. The cur rent set ting of thefea ture is dis played on the LCD dis play. The first screento the right is cur rently set to a de fault of “A” chan nel,nonlatching.
• While con tin u ing to hold [SET] press [WTA] again to goto the next se lec tion; Talk Around = “B” chan nel,non-latching.
• Talk Around = “A” + “B” chan nels, non-latching.
• Talk Around = “Push-But ton”, non-latching. What evertalk but ton is ac tive be comes wire less talk around.
• Talk Around = “A” chan nel, latch ing.
• Talk Around = “B” chan nel, latch ing.
• “A” + “B” chan nels, latch ing.
• Talk Around = “Push-Button”, latch ing. What ever talkbut ton is ac tive be comes wire less talk around.
• While con tin u ing to hold [SET], press [SA] once again todis play the fi nal menu op tion “Talk Around = Off”. Re -lease the [SET] but ton on any of the above screens to ac -cept the cur rent dis played set ting and re turn to theGroup/Chan nel screen.
7-31
CONTINUE TO HOLD [SET]AND PRESS [WTA] AGAIN
END
03A 01GP CH
tA oFF
HOLD [SET] AND PRESS [WTA]
tA b
tA Ab
dEF A L
dEF bL
dEF AbL
CONTINUE TO HOLD [SET]AND PRESS [WTA] AGAIN
CONTINUE TO HOLD [SET]AND PRESS [WTA] AGAIN
CONTINUE TO HOLD [SET]AND PRESS [WTA] AGAIN
CONTINUE TO HOLD [SET]AND PRESS [WTA] AGAIN
CONTINUE TO HOLD [SET]AND PRESS [WTA] AGAIN
RELEASE [SET]
tA Pb
CONTINUE TO HOLD [SET]AND PRESS [WTA] AGAIN
tA PbL
CONTINUE TO HOLD [SET]AND PRESS [WTA] AGAIN
tA A
![Page 66: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/66.jpg)
TR-825 Menu Struc ture
Au dio Chan nel A Options
• Press and hold [SET] then hit the [A] but ton to show thechan nel “A” menu screen. The cur rent set ting of the but -ton is dis played on the LCD dis play; Chan nel “A”“Talk-Latching Off”.
• While con tin u ing to hold [SET], press the [A] but tonagain to move to the next op tion; Chan nel “A” Talk -Latching On.
• As you con tinue to hold [SET], press the [A] but ton oncemore to move to the next op tion, Chan nel “A” Off.
• Re lease the [SET] but ton to ac cept the cur rent dis playedset ting and re turn to the Group/Chan nel screen.
7-32
A on
CONTINUE TO HOLD [SET]AND PRESS [A] AGAIN
END
03A 01GP CH
HOLD [SET] AND PRESS [A]
A L on
A oFF
CONTINUE TO HOLD [SET]AND PRESS [A] AGAIN
RELEASE [SET]
Au dio Chan nel A Op tions
![Page 67: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/67.jpg)
TR-825 Menu Struc ture
Au dio Chan nel B Op tions
• Press and hold [SET] then hit the [B] but ton to show thechan nel “B” menu screen. The cur rent set ting of the but -ton is dis played on the LCD dis play; Chan nel “B”Talk-Latching Off.
• While con tin u ing to hold [SET], press the [B] but tonagain to move to the next op tion; Chan nel “B”Talk-Latching On.
• As you con tinue to hold [SET], press the [B] but ton oncemore to move to the next op tion, Chan nel “B” Off.
• Re lease the [SET] but ton to ac cept the cur rent dis playedset ting and re turn to the Group/Chan nel screen.
7-33
b on
CONTINUE TO HOLD [SET]AND PRESS [B] AGAIN
END
03A 01GP CH
HOLD [SET] AND PRESS [B]
b oFF
CONTINUE TO HOLD [SET]AND PRESS [B] AGAIN
RELEASE [SET]
b L on
Au dio Chan nel B Op tions
![Page 68: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/68.jpg)
TR-825 Menu Struc ture
Spe cial Key Se quences
Lock out
• Press [UP]+[DOWN] for 3 sec onds to lock or un lock thebeltpack. The words “Loc on” will be dis played when thefea ture is ac ti vated, “Loc oFF” will be dis played when the beltpack is un locked. Pressing [MENU] will still func tionto view screens, but [SET] will no lon ger start any ed it -ing. ClearScan™, First use, Fac tory de fault, and Fea tureen able/dis able are no lon ger ac ces si ble. The words “Locout” will be flashed on the screen if any ed it ing is at -tempted dur ing lock out.
1st Use De fault
• Press [MENU] while turn ing on the beltpack to en ter the1st use de fault setup screen. This places the unit on group01A with chan nel 01 flash ing. Any user-programmedfre quen cies that had been en tered pre vi ously are re -tained. The beltpacks must now be set to dif fer ent trans -mit chan nels us ing the [UP]/[DOWN] but tons. Then[SET] is hit to place the units on those chan nels. If lock -out had been ac ti vated, the beltpack co mes up where itwas last left re gard less of [MENU] be ing pressed onpower-up.
Fac tory De fault
• Pressing all four but tons [MENU]+[SET]+[UP]+[DOWN] at the same time places the unit on group 01A with chan -nel 01 flash ing, just like beltpack 1st use de fault, ex ceptthe all user-programmed fre quen cies that had been en -tered pre vi ously are erased. The beltpacks must now beset to dif fer ent trans mit chan nels us ing the [UP]/[DOWN] but tons. Then [SET] is pressed to place the units onthose chan nels. If lock out had been ac ti vated, thebeltpack co mes up where it was last left re gard less ofthese four keys be ing pressed.
7-34
![Page 69: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/69.jpg)
Sys tem Walk-Thru
Now that you have suc cess fully “set-up” your Telex Wire lessInter com Sys tem and turned on any aux il iary equip ment, youare ready to test the over all per for mance by “Walking” theTelex sys tem through the ar eas in which you will be us ing it.
Be fore you be gin your walk-thru, check the fol low ing:
r Beltpack Bat tery Check.
r Set mi cro phone gain in both the beltpack(s) and thebase sta tion.
r The base sta tion and beltpack(s) are on the same group and the beltpack(s) are on their own unique trans portchan nels that match the base sta tion re ceive chan nels
r Check that the talk but ton is en gaged. The talk LEDwill be il lu mi nated.
r In ter com Level “IN” and “OUT” are set to an ap pro -pri ate level.
r Auxiliary Level “IN” and “OUT” are set to an ap pro -pri ate level (if used).
The “sys tem walk-thru” can de tect prob lem of weak sig nalstrength caused by:
• Poor an tenna lo ca tion
• Wrong an tenna for re ceiver and/ or trans mit ter
• RF “Trou ble Spots”
• Op er ating dis tance be yond sys tem ca pa bil ity.
• Old or used bat ter ies in the TR-8XX.
Un der nor mal con di tions the base sta tion’s dis play will in di catea beltpack sta tus. “Weak Sig nal” con di tion will re sult in “no tx” be ing dis played on the base sta tion’s re ceiver for that beltpack.
In 99% of all in stances you will set up your Telex Wire less In --ter com Sys tem, walk it through the area of in ter est andachieve error-free per for mance. If in the rare in stance yourTelex sys tem does not “pass” dur ing your walk-thru eval u a --tion, re fer to the sec tion of this man ual which deals with Sys --tem Trou ble shooting.
8-1
Section
8
![Page 70: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/70.jpg)
8-2 Blank
![Page 71: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/71.jpg)
Trou ble shooting
Re read the sec tions of this manual to make sure you havecom pleted sys tem set-up prop erly.
If you are un able to solve the prob lem, con tact the dealer from whom you purchased the sys tem for as sis tance.
9-1
Section
9
PROBLEM SOLUTION
DISTORTION - System’s audio quality seems distortedat medium to high input levels.
Reduce microphone gain by adjusting microphone gaincontrol.
HISS - System seems to produce a “hiss” which isundesirable.
Check the gain setting on all beltpacks and the base. Theymay be too low or too high. Check to make sure you arestill well within range of the base station.
LOW OUTPUT - System produces a low output level.Check the gain setting on both the beltpacks and the base.They may be too low.
FEEDBACK - Moving around area of use produces“squeal” or “howl” in various locations using ext.speakers.
Reduce the gain settings on both the beltpacks and thebase. They may be too high.
DROPOUTS - When moving around the area of use there seems to be locations where the signal “swooshes” orcompletely disappears.
Make sure both antennas on the base and beltpack areconnected and follow the location suggestions. Change the location of the base unit and antennas or avoid the badareas with the remote beltpacks.
INTERFERENCE - System picks up signals other thanwireless intercoms.
Make sure that all the Telex beltpack(s) are on. If there are any unused receivers at the base, turn the audio off fromthose receivers by deselecting the appropriate “PortableStation Connect” button.
If problems persist with the beltpack on, you will probably need to change the group. Make sure the base andbeltpack match after any Group/Channel change.
NO AUDIO from BASE or BELTPACK headsets.
Check Transmitter switch on base and beltpack. Checktalk LED to make sure it is on. Make sure beltpackbatteries are OK.
![Page 72: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/72.jpg)
9-2 Blank
![Page 73: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/73.jpg)
Tech Tips
Fre quency In ter ac tion
Un for tu nately, ra dio fre quency (RF) chan nels can not be ran --domly se lected for use in ra dio de vices. They must be se lected to avoid known fre quen cies in use, FCC re stric tions on the lo --ca tion of de vices, and even in ter fer ence be tween your own RF de vices. The fac tory de fined fre quen cies (Groups 01A-24) se --lected by Telex for this RadioCom™ sys tem are cho sen tomin i mize pos si ble in ter fer ence.
Mi cro phone Gain Ad just ment
The mi cro phone gain con trols on the base sta tion and beltpack are set to mid-levels by the fac tory. In most cases this set tingwill work f ine and only on loud speech wil l theovermodulation (OM) in di ca tor light. How ever, in en vi ron --ments where the back ground noise is loud or the user has astrong/quiet voice, the gain con trol will need to be ad justed. In Fig ure 33 the gain is set cor rectly. The user’s root-mean-square (RMS) sound level is well be low the OM thresh old and onlyon peaks does his or her voice flash the OM in di ca tor light.
Fig ure 34 dis plays the same gain set ting as in Fig ure 33 butbrought into a high noise en vi ron ment. The user’s voice nowlights the OM in di ca tor all the time he or she speaks due to the higher noise plus the user speak ing louder. The re sult on thesys tem is dis tor tion on louder speech. The mi cro phone gainmust be re duced. The same ap plies to a user with a pow er fulvoice. If some one sets the sys tem mic gain to their voice anduser has a much stron ger voice, then the gain will need to bere duced, even if the back ground noise is the same.
Al ways re mem ber to set the mi cro phone gain based on the sit --u a tion and lo ca tion in which the equip ment will be used. If the equip ment is used on the field dur ing a foot ball game, set thegain based upon a loud sta dium, NOT the quiet sta dium 2hours be fore a game. If a pro duc tion stu dio user has a quietvoice, set the gain to their voice and NOT the stage hand’sloud voice who helped set up the sys tem.
10-1
OM THRESHOLD
USER'S VOICE
NOISESO
UN
D L
EV
EL
, R
MS OM THRESHOLD
USER'S VOICE
NOISE
SO
UN
D L
EV
EL
, R
MS
Fig ure 33Low Noise En vi ron ment
Mi cro phone Gain Set Cor rectly
Fig ure 34High Noise En vi ron ment
Mi cro phone Gain Set Too High
Section
10
![Page 74: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/74.jpg)
10-2 Blank
![Page 75: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/75.jpg)
Bat tery Information
Im proper bat tery se lec tion, use, in stal la tion and care are thecause of nu mer ous wire less sys tem fail ures.
Al ka line Bat teries: Al ka line bat ter ies such as Mallory’sDURACELL® or Eveready’s EN ER GIZER® pro vide themost re li able op er a tion in wire less trans ceiv ers.
The use of low cost car bon-zinc bat ter ies is NOT rec om --mended.
Nickel-Metal Hy dride Bat teries: These bat ter ies can saveyou money in the long run, as they can be re charged. Typ i calbat tery life is about 70-80% of the length of time al ka line bat --ter ies last.
Bat tery Life:
TR-800Al ka line, 12-14 HoursNickel Metal Hy dride, 9-11 Hours
TR-825Al ka line, 9-11 HoursNickel Metal Hy dride, 7-9 Hours
WARNING:Do not place an al ka line TR-8XX bat tery pack in any bat terycharger. Se vere charger and bat tery pack dam age may re sult.
11-1
En er gizer® is a reg is tered trade mark of Un ion Car bide Cor po ra tion.Duracell® is a reg is tered trade mark of Duracell Inc.
Section
11
![Page 76: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/76.jpg)
11-2 Blank
![Page 77: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/77.jpg)
In ter com Sys tems Spec i fi ca tions
12-1
Section
12
RTS
In put Im ped ance:...............................................................200W
Out put Level: .............................................0.775 Vrms nom i nal
Bridg ing Im ped ance:.......................................................>10kW
Call Sig naling:
Send: ...................................20kHz ±100 Hz, 240 mVrms
Re ceive: .............................20kHz ±800 Hz, 100 mVrms
Power Volt age: ............................................28.0 VDC nom i nal
2
COMMON
1
3
AUDIO 1 PLUS POWER
AUDIO 2
MALE
AudioCom/Telex
In put Im ped ance:...............................................................300W
Out put Level: .................................................1.0 Vrms nom i nal
Bridg ing Im ped ance:.......................................................>10kW
Call Sig naling:
Send: ....................................20kHz ± 100 Hz, 05 mVrms
Re ceive: .............................20kHz ±800 Hz, 100 mVrms
Power Volt age: ............................................24.0 VDC nom i nal
2
COMMON
1
3
AUDIO ( - ) PLUS POWER
AUDIO ( + ) PLUS POWER
MALE
Clear-Com
In put Im ped ance:...............................................................200W
Out put Level: .................................................1.0 Vrms nom i nal
Bridg ing Im ped ance:.......................................................>10kW
Call Sig naling:
Send:................................................................12 ±3 VDC
Re ceive: ...............................................4 VDC Min i mum
Power Volt age: ............................................30.0 VDC nom i nal
2
COMMON
1
3
POWER
AUDIO
MALE
![Page 78: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/78.jpg)
12-2 Blank
![Page 79: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/79.jpg)
Ac ces sories and Re place ment Parts
BTR Power CordsNorth Amer ica ................................................... 550024013U.K. ....................................................................550024002Eu ro pean.............................................................550024000Aus tra lian............................................................550024018
BTR In ter com Dummy Load
Telex type ...........................................................PN 878935RTS type .............................................................PN 878990
SA Re lay screw plug adapter..............................PN 2862046
TR LCD/switch cover............................................PN 450364
BP-700 TR Bat tery pack, al ka line
(bat ter ies not in cluded)..................................PN 71315-000
BP-800NM TR Nickel Metal Hy dride 2200mAh
Bat tery pack..................................................PN 71315-002
U.S./Can ada...PRD00007008
Euro .............PRD00007009
U.S./Can ada. PRD000070006
Euro ............. PRD000070007
13-1
Section
13ALP-600520-760 MHz Bi-Directional Log Pe ri odicAn tenna In cludes mount ing hard ware and10 feet (3 me ters) of co ax ial ca ble with TNC Con nec tors ALP-450450-900 MHz Log Pe ri odic An tennaIn cludes mount ing hard ware and 10 feet (3me ters) co ax ial ca ble with TNC con nec tors
An tenna Ca blesSpe cial low loss an tenna ca bles with TNC Con nec tors
BC-800NM4
Four Slot “Smart” Charger
with Four Nickel Metal
Hy dride Bat tery Packs
BC-800NM
Single Slot “Smart” Charger
with Nickel Metal Hy dride Bat -
tery Pack
Model No. Length Or der No.CXU-10 10 Ft. (3 me ter) 690419CXU-25 25 Ft. (7.6 me ter) 71151-025CXU-50 50 Ft. (15 me ter) 71151-050CXU-75 75 Ft. (23 me ter) 71151-075
CXU-100 100 Ft. (30 me ter) 71151-100
P N. 878896
Or der No. 71147000
Part
No.
879220-1
879220-2
879220-3
879220-4
879220-5
879220-6
Frequency Coverage of
Antenna
425.0 - 488.0 MHz
485.0 - 553.9 MHz
554.0 - 635.9 MHz
636.0 - 725.9 MHz
726.0 - 826.0 MHz
826.0 - 930.0 MHz
Mhz
Band
Color
Violet
Black
Yellow
Green
Red
Blue
Beltpack RX Band Beltpack TX Band
F H A B C D E 88 1 2 3 4 5 6
X
X X X X
X X X X
X X X X X
AB-2
Beltpack 1/4 - Wave An tennas
Base Sta tion:Flex i ble Ground In de pend ent Di pole Antennas
Bracket for 1/2 wave An tenna with 10 ft. of coax- PN 71138000
![Page 80: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/80.jpg)
13-2 Blank
![Page 81: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/81.jpg)
Soft ware Li cense
14-1
End-User Li cense Agree ment for Telex® Soft ware
IM POR TANT - Please red this doc u ment care fully be fore us ing this prod uct.
THIS DOC U MENT STATES THE TERMS AND CON DI TIONS UPON WHICH TELEX COM MU NI CA TIONS,INC. (the “COM PANY”) OF FERS TO LI CENSE THE IN STALLED SOFT WARE OR PRO GRAM (the “SOFT -WARE”) FOR USE WITH THE PRO DUCT IN WHICH IT WAS IN STALLED. YOU ARE AGREEING TO BE -COME BOUND BY THE TERMS OF THIS AGREE MENT. IF YOU DO NOT AGREE TO THE TERMS OF THISAGREE MENT, DO NOT USE THIS PRO DUCT. PROMPTLY RE TURN THE PRO DUCT TO THE PLACEWHERE YOU OB TAINED IT FOR A FULL RE FUND.
The in stalled soft ware as sup plied by the Com pany is li censed, not sold, to you for use only un der the terms of this li -cense, and the Com pany re serves all rights not ex pressly granted to you. You own the prod uct or other me dia on or inwhich the Soft ware is orig i nally or sub se quently re corded or fixed, but the Com pany re tains own er ship of all cop iesof the Soft ware it self.
1. Li cense: This li cense al lows you to use the Soft ware for in ter nal pur poses only on a sin gle prod uct in which it was in -stalled.
2. Re stric tions: (a) You may not mar ket, dis trib ute or trans fer cop ies of the Soft ware to oth ers or elec tron i cally trans feror du pli cate the soft ware. YOU MAY NOT RE VERSE EN GINEER, DECOMPILE, DIS AS SEM BLE, MODIFY,ADAPT, TRANS LATE, RENT, LEASE OR LOAN THE SOFT WARE OR CRE ATE DE RIV A TIVE WORKSBASED ON THE SOFT WARE OR ANY AC COM PANYING WRITTEN MA TE RIALS. (b) The Soft ware and theac com pa ny ing writ ten ma te ri als are copy righted. Un au tho rized copy ing of the Soft ware, in clud ing por tions thereof orthe writ ten ma te ri als, is ex pressly for bid den. (c) You un der stand that the Com pany may up date or re vise the Soft wareand in so do ing in curs no ob li ga tion to fur nish such up dates to you.
3. Limited War ranty: The com pany does not war rant that the op er a tion of the Soft ware will meet your re quire ments orop er ate free from er ror. The com pany DIS CLAIMS ALL OTHER WAR RANTIES AND CON DI TIONS EITHEREX PRESS OR IM PLIED, IN CLUDING THE WAR RANTIES OF MER CHANT ABIL ITY, FIT NESS FOR A PAR -TIC U LAR PUR POSE AND NON-INFRINGEMENT OR THIRD PARTY RIGHTS.
4. Limited Li a bil ity: The li a bil ity of the com pany for any claims aris ing out of this Li cense based upon the Soft ware, re -gard less of the form of ac tion, shall not ex ceed the greater of the li cense fee for the Soft ware or $50.
Section
14
![Page 82: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/82.jpg)
14-2 Blank
![Page 83: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/83.jpg)
Certification In for ma tion
15-1
FCC
The Telex BTR-800, TR-800, and the TR-825 Trans mit ter/Re ceiver are Type Ac cepted un der United StatesFed eral Com mu ni ca tions Com mis sion Part 74. Part 74 li cens ing of the equip ment is the User’s re spon si bil -ity and licensibility de pends on the user’s clas si fi ca tion, us ers ap pli ca tion, and fre quency se lected. Telexstrongly urges the user to con tact the ap pro pri ate tele com mu ni ca tions au thor ity for any de sired clar i fi ca tion.
This de vice com plies with Part 15 of the FCC Rules. Op er a tion is sub ject to the con di tion that this de vicedoes not cause harm ful in ter fer ence.
CAU TION: Changes or mod i fi ca tions made by the user could void the user’s au thor ity to op er ate theequip ment.
NO TICE: This wire less mi cro phone sys tem can be con fig ured for both FCC Part 15 (unlicensed) and FCCPart 74 (li censed) op er a tion. When shipped from the fac tory, this wire less mi cro phone sys tem is con fig uredfor unlicensed op er a tion, and will op er ate at a power level not to ex ceed 50 milliwatts, which meets FCCPart 15 re quire ments. If unlicensed us ers op er ate this de vice in ex cess of 50 milliwatts, harm ful in ter fer ence may re sult and the unlicensed user will be sub ject to sub stan tial mon e tary for fei tures and other FCC sanc -tions. The wire less mi cro phone sys tem may be op er ated by hold ers of a valid FCC li cense in the LowPower Aux il iary Ra dio Ser vice un der Part 74 of FCC Rules, at power lev els be tween 50 milliwatts and 250milliwatts.
Man da tory Safety In struc tions
to Base Sta tion In stall ers and Us ers
1. Use only man u fac turer or dealer sup plied an tenna. An tenna min i mum safe dis tance, as cal cu lated fromFCC re quire ments, is 4.8cm. How ever, the FCC de fault for the min i mum safe dis tance is 20cm. An tennagain: zero dBd ref er enced to a di pole.
2. The FED ERAL COM MU NI CA TIONS COM MIS SION has adopted a safety stan dard for hu man ex po sure to RF (Ra dio Fre quency) en ergy, which is be low the OSHA (Oc cu pa tional Safety and Health Act) lim its.
3. To com ply with cur rent FCC RF Ex po sure lim its, the an tenna must be in stalled at or ex ceed ing the min i -mum safe dis tance show here, and in ac cor dance with the re quire ments of the an tenna man u fac turer orsup plier.
4. An tenna sub sti tu tion: Do Not sub sti tute any an tenna for the one sup plied by or rec om mended by the man -u fac turer or ra dio dealer. You may be ex pos ing per son or per sons to harm ful ra dio fre quency ra di a tion.You may con tact your ra dio dealer or the man u fac turer for fur ther in struc tions.
5. WARN ING: Main tain a sep a ra tion dis tance from the an tenna to per son(s) of at least 20cm.
You, as the qual i fied end-user of this ra dio de vice must con trol the ex po sure con di tions of by stand ers toen sure that the min i mum sep a ra tion dis tance (above) is main tained be tween the an tenna and nearby per -sons for sat is fy ing RF Ex po sure com pli ance.
The op er a tion of this trans mit ter must sat isfy the re quire ments of the Gen eral Pop u la tion/Un con trolled Ex -po sure En vi ron ment for work-re lated use. Trans mit only when per son(s) are at least the min i mum dis -tance from the prop erly in stalled, ex ter nally mounted an tenna.
Section
15
![Page 84: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/84.jpg)
15-2
In dus try Can ada
The Telex BTR-800, TR-800, TR-825 trans mit ter/re ceiver are cer ti fied to In dus tryCan ada RSS-123 rules
Li cens ing of Telex equip ment is the us ers re spon si bil ity and licensability de pendsupon the user's clas si fi ca tion, user's ap pli ca tion and fre quency se lected. Telex stronglyurges the user to con tact the ap pro pri ate telecommunicatins au thor ity for any de siredclar i fi ca tion.
CAU TION: Any changes or mod i fi ca tions made to the above equip ment could voidthe user's au thor ity to operat the equip ment.
Europe
Ver sions of the BTR-800, TR-800 and TR-825 which dis play the "CE" sym bol on the unit arecer ti fied to ETSI EN 300 454-2, ETSI EN 301 489-9 and EN 60950 stan dards. These unitscon form to Eu ro pean Un ion di rec tives, el i gi ble to bear CE mark ing. See next pagefor the dec la ra tions of con for mity.
This equip ment is in com pli ance with the fol low ing di rec tives;
2002/95/EC RoHS Di rec tive2002/96/EC WEEE Di rec tive
Please dis pose of the base sta tion and beltpacks at the end of its op er a tional life by tak --ing it to your clos est col lec tion point or re cy cling cen ter.
This equip ment is in tended for use in pro fes sional au dio in ter com ap pli ca tions.
A li cense may be re quired to op er ate this equip ment in cer tain re gions! Con sultyour na tional au thor ity for pos si ble re quire ments.
![Page 85: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/85.jpg)
15-3
![Page 86: BTR-800, TR-800](https://reader034.vdocuments.us/reader034/viewer/2022051007/586e1b331a28ab29208ba0b0/html5/thumbnails/86.jpg)
BOSCH SE CU RITY SYSTEMS • 12000 Port land Ave. South, Burnsville, MN 55337.
PN 803257-1 Rev. P JUL 2010 Made in U.S.A.