bs chain for corrosive environments · 2019-10-12 · low noise (5 db lower than bs standard roller...
TRANSCRIPT
16
BS CHAIN FOR CORROSIVE ENVIRONMENTS
Corrosion Resistant Chain(Stainless Steel base)
BS PC Engineering Plastic Combination ChainThe pins and pin link plates of these chains are made of SUS304 equivalent (spring clips SUS301). Engineering plastic (white) is used for the inner link. This combination makes it a lube-free, low noise (5 dB lower than BS standard roller chain) and light-weight chain (50% lighter than BS standard roller chain). Working temperature range: -20°C to +80°C. For details on corrosion resistance, please check out the table in the back of this catalogue.
BS SS Stainless Steel ChainAll basic components of this chain are made of Stainless Steel SUS304 equivalent (except the spring clips, which are made of SUS301). This chain can be used in special environments such as under water, acidic and alkaline applications. It can also be used in high and low temperatures (-20°C to +400°C). SUS304 equivalent is only marginally magnetic, which is the result of the cold-forging process. For details on corrosion resistance, please check out the table in the back of this catalogue.
Corrosion Protected Chain(Carbon Steel base)
BS NEPTUNE™ Surface Treated ChainBS NEPTUNE™ Chain is a TSUBAKI BS chain that has undergone a special surface treatment. The link plates, bushes and bearing pins have a special three stage layer applied in order to provide the maximum protection from the operating or environmental conditions. (Spring clips are SUS301). NEPTUNE™ Rollers have a special coating designed to resist the corrosive conditions as well as the severe dynamic contact between roller and sprocket.
This chain is suitable for use in environments exposed to sea-water, acid-rain and other adverse weather conditions. This chain does not contain any chemically hazardous substances such as Hexavalent Chromium, Lead, Cadmium and Mercury as regulated by RoHS√. The kilowatt ratings are the same as those of the corresponding BS chain with a working temperature range: -10°C to +150°C. Above +60°C a special high-temperature lubrication is required. Of course, BS LAMBDA NEPTUNE™ chain is also available.
BS NP Nickel Plated ChainBS NP Chain is a TSUBAKI BS chain that has been plated with Nickel. NP Chain has a light corrosion resistance and an attrac-tive appearance. NP Chain is suitable for outdoor conditions exposed to water. There is a 15% reduction in Maximum Allowable Load compared to the corresponding BS chain, so please take this into account when making your chain selection. It has a working temperature range of: -10°C to +60°C. Of course, BS LAMBDA NP chain is also available.
√ RoHS = Restriction of Hazardous Substances
Whether your operation requires a sanitary environment, is exposed to corrosive
chemicals, is heated to extreme temperatures, runs through a freezer, is exposed to
the outdoors or is affected by excessive moisture: our specially designed and tested
chains will outlast your current chains and contribute to a cost effective application.
18
L2
L1
d2 d1
p
H
T
t
p
b1
d2 d1
T
b1
L2
L1 t
pt
d2 d1
T
b1 L2
L1
t pt
pt
OL
L
L1
L1
2POL
BS CHAIN FOR CORROSIVE ENVIRONMENTS
BS SS ChainDimensions in mm
TSUBAKIChain No.
PitchRoller
DiameterInner Width
Pin Link Plate
Transverse Pitch
Max. Allowable
Loadacc. to Tsubaki
Approx. MassDiameter Length Length Length Thickness Thickness Height
p d1 b1 d2 L1 L2 L T t H (max) pt kN kg/mRF06B-SS-1
9.525 (3/8”) 6.35 5.72 3.286.50 7.25 15.45
1.30 1.00 8.20- 0.27 0.39
RF06B-SS-2 11.60 12.30 25.85 10.24 0.53 0.75RS08B-SS-1
12.70 (1/2”) 8.51 7.75 4.458.35 10.05 20.05
1.50 1.50 11.80- 0.48 0.70
RS08B-SS-2 15.30 17.00 34.60 13.92 0.96 1.35RS08B-SS-3 22.25 23.95 48.60 13.92 1.44 2.00RS10B-SS-1
15.875 (5/8”) 10.16 9.65 5.089.55 11.25 22.90
1.50 1.50 14.70- 0.66 0.95
RS10B-SS-2 17.85 19.55 39.40 16.59 1.32 1.85RS10B-SS-3 26.20 27.80 56.00 16.59 1.97 2.80RS12B-SS-1
19.05 (3/4”) 12.07 11.68 5.7211.10 13.00 26.70
1.80 1.80 16.10- 0.87 1.25
RS12B-SS-2 20.90 22.70 46.10 19.46 1.74 2.50RS12B-SS-3 30.65 32.55 65.60 19.46 2.62 3.80RS16B-SS-1
25.40 (1”) 15.88 17.02 8.2817.75 19.95 43.70
4.00 3.20 21.00- 2.06 2.70
RS16B-SS-2 33.55 35.75 75.50 31.88 4.12 5.40RS20B-SS-1 31.75 (1 1/4”) 19.05 19.56 10.19 20.10 23.20 48.40 4.50 3.50 26.00 - 2.84 3.85
Note:
1. Connecting links are clip type for sizes up to RS16B-SS, and cotter type for sizes RS12B-SS to RS20B-SS.
2. RF06B-SS chain has flat shaped link plates.
3. Center sink pins are not available. Double stake riveting is applied.
4. For details on corrosion resistance selection, please consult our Corrosion Resistance Guide in this catalogue.