browse valeo catalog pdf (11.7 mb)
TRANSCRIPT
Table of Contents
1
Important explanatory information 2
DC motors with worm gear0225 (GMPG) 8
0321 (GMPS) 16
0320 (GMPD) 21
0266 (DCK31) 32
0270 (SWMK) 58
0268 (DCK35) 61
0277 (SW2K) 65
0278 (SW2L) 74
0291 (SWMV) 80
0292 (SWMG) 85
DC motors with spur gear0231 (GMPI) 88
Plain DC motors0220 (GMP) 94
0272 (GMK) 103
0273 (GML) 110
Index 117
Important explanatory information
2
Table of Contents Page
Terms, symbols and units according to DIN 3
Conversion of torques 4
Conversion of forces 4
Conversion of power 4
Conversion of temperatures 5
Tolerance zones to ISO/R 286 5
Characteristic curves 6
Tolerance zones 7
Important explanatory informationTerms, symbols and units according to DIN
3
Important catalogue explanatory information
Subject to change and error, also of a technical nature. Therefore use only product drawings for design purposes. These are available from your representative.
The catalogue illustrations do not all correspond to DIN requirements. The operating values indicated are valid for 20°C ambient temperature. In all cases the motors should be tested for their suitability in the customer's particular application. Specific motor designs for special customers.
Motors in this catalogue are not intended for the consumer. In accordance with EU regulations, these products do not require CE certification marking.
Some motors have customer specific designs. They require new tooling for new designs.
Terms, symbols and units according to DIN
Symbol Unit Term
UN [V] Rated voltage
n0 [min-1] No-load speed ± 10%
MN [Nm] Nominal torque at the output shaft
MA [Nm] Starting torque
i Gear ratio
JR [kgm2] x 10-6 Armature load inertia
R [mΩ] Armature resistance, 2/4 commutator bars
L [mH] Armature inductance, 2/4 commutator bars
Drawing: dimensional drawing
Shaft: dimensions of shaft ends
Wiring diagram: motor wiring diagram
Connection: dimensions and positions of motor connections
Materials: BRZ=bronze, KST=plastic, ST=steel, HGW=resinbonded fabric
Direction of rota-tion when looking onto motor shaft
The curves show the speed and the current as a function of the torque. These are aver-age values at room temperature. Divergences of ± 10 % are possible in the series.
Worm gear motors have a preferred direction of rotation, indicated in the drawings by a larger arrow. If the motor rotates against the pre-ferred rotation direction, power decreases by approx. 10%.
Preferred direction of rotation:
left-hand right-hand
Important explanatory informationConversion of torques
4
Conversion of torques (values rounded for practical use)
Conversion of forces (values rounded for practical use)
Conversion of power (values rounded for practical use)
Ncm Nm pcm kpcm kpm oz-in in-lbs ft-lbs
Ncm 1 10-2 102 1,02 · 10-2 1,02 · 10-3 1,42 8,85 · 10-2 7,38 · 10-3
Nm 100 1 10,2 · 103 10,2 0,102 141,6 8,85 0,738
pcm 9,8 · 10-3 9,8 · 10-5 1 10-3 10-5 1,39 · 10-2 8,68 · 10-4 7,23 · 10-5
kpcm 9,8 9,8 · 10-2 1000 1 10-2 13,9 0,868 7,23 · 10-2
kpm 980 9,8 105 100 1 1390 86,8 7,23
oz in 0,706 7,06 · 10-3 72 7,2 · 10-2 7,2 · 10-4 1 6,25 · 10-2 5,2 · 10-3
in lbs 11,3 0,113 1152 1,15 1,15 · 10-2 16 1 8,3 · 10-2
ft lbs 135,58 1,36 13 825 13,8 0,138 192 12 1
N kp p oz lbf
N 1 0,102 102 3,6 0,225
kp 9,8 1 1000 35,27 2,2
p 9,8 · 10-3 10-3 1 3,53 · 10-2 2,2 · 10-3
oz 0,278 2,83 · 10-2 28,35 1 6,25 · 10-2
lbf 4,45 0,445 453,6 16 1
kw PS HP kpm/s kcal/s
kw 1 1,36 1,34 102 0,239
PS 0,735 1 0,986 75 0,176
HP 0,746 1,01 1 76 0,178
kpm/s
9,8 · 10-3 1,33 · 10-2 1,32 · 10-2 1 2,34 · 10-3
kcal/s
4,2 5,7 5,6 427 1
Important explanatory informationConversion of temperatures
5
Conversion of temperatures (values rounded for practical use)
Tolerance zones to ISO/R 286 (DIN 7150, 7151, 7152, 7154, 7155)
tC [°C] CelsiustF [°F] Fahrenheit
TK [K] KelvinTR [°R] Rankine
1,1 H 13: +0,140 / 0 mm 6 h 6: 0 / -0,008 mm 12 h 6: 0 / -0,011 mm1,6 H 13: +0,140 / 0 mm 6 h 8: 0 / -0,018 mm 12 h 7: 0 / -0,018 mm2,5 H 12: +0,100 / 0 mm 6 h 9: 0 / -0,030 mm 12 h 9: 0 / -0,036 mm2,7 H 12: +0,100 / 0 mm 6 m 6: +0,012 / +0,004 mm 12 h 11: 0 / -0,110 mm3 H 9: +0,025 / 0 mm 6,3 H 12: +0,150 / 0 mm 13,4 h 11: 0 / -0,110 mm3 H 12: +0,100 / 0 mm 6,5 H 8: +0,022 / 0 mm 14 f 6: -0,016 / -0,027 mm3 N 9: -0,004 / -0,029 mm 6,8 h 8: 0 / -0,022 mm 14 f 7: -0,016 / -0,034 mm3 P 8: -0,006 / -0,020 mm 7 h 8: 0 / -0,022 mm 14 H 7: +0,018 / 0 mm3 P 9: -0,006 / -0,031 mm 7,6 h 11: 0 / -0,090 mm 15 f 7: -0,016 / -0,034 mm3 P 10: -0,006 / -0,046 mm 8 f 6: -0,013 / -0,022 mm 15,2 h 11: 0 / -0,110 mm3,1 JS 10: +0,024 / -0,024 mm 8 g 6: -0,005 / -0,014 mm 16 f 6: -0,016 / -0,027 mm3,5 H 12: +0,120 / 0 mm 8 g 7: -0,005 / -0,020 mm 18 H 8: +0,027 / 0 mm3,6 H 11: +0,075 / 0 mm 8 g 9: -0,005 / -0,041 mm 20 h 9: 0 / -0,052 mm4 C 10: +0,118 / -0,070 mm 8 h 9: 0 / -0,036 mm 26 g 6: -0,007 / -0,020 mm4 h 6: 0 / -0,008 mm 8 H 9: +0,036 / 0 mm4 h 8: 0 / -0,018 mm 8 h 10: 0 / -0,058 mm4 h 9: 0 / -0,030 mm 8 h 11: 0 / -0,090 mm4 h 10: 0 / -0,048 mm 8 k 5: +0,007 / +0,001 mm4 h 11: 0 / -0,075 mm 8,5 h 9: 0 / -0,036 mm4 H 12: +0,120 / 0 mm 8,7 h 11: 0 / -0,090 mm4 P 9: -0,012 / -0,042 mm 9 D 9: +0,076 / +0,040 mm4,1 h 10: 0 / -0,048 mm 9 h 6: 0 / -0,009 mm4,1 H 11: +0,075 / 0 mm 9 h 11: 0 / -0,090 mm4,2 H 7: +0,012 / 0 mm 9 k 5: +0,007 / +0,001mm4,2 H 12: +0,120 / 0 mm 9,4 h 11: 0 / -0,090 mm4,5 H 13: +0,180 / 0 mm 9,5 js 11: +0,045 / -0,045 mm5 c 11: -0,070 / -0,145 mm 9,6 h 11: 0 / -0,090 mm5 h 6: 0 / -0,008 mm 9,75 g 5: -0,006 / -0,014 mm5 h 9: 0 / -0,030 mm 10 f 6: -0,013 / -0,022 mm5 h 10: 0 / -0,048 mm 10 f 7: -0,013 / -0,028 mm5 h 12: 0 / -0,120 mm 10 f 8: -0,013 / -0,035 mm5 P 9: -0,012 / -0,042 mm 10 g 5: -0,005 / -0,011 mm5,1 H 11: +0,075 / 0 mm 10 g 6: -0,005 / -0,014 mm5,1 H 12: +0,120 / 0 mm 10 h 5: 0 / -0,006 mm5,5 h 11: 0 / -0,075 mm 10 h 7: 0 / -0,015 mm5,5 H 13: +0,180 / 0 mm 10 h 9: 0 / -0,036 mm5,8 g 6: -0,004 / -0,012 mm 11 d 10: -0,050 / -0,120 mm5,9 c 9: -0,070 / -0,100 mm 11,2 e 10: -0,032 / -0,102 mm5,9 h 10: 0 / -0,048 mm 11,5 h 11: 0 / -0,110 mm6 f 9: -0,010 / -0,040 mm 12 f 7: -0,016 / -0,034 mm6 fg 9: -0,006 / -0,014 mm 12 g 5: -0,006 / -0,014 mm
Important explanatory informationCharacteristic curves
6
Characteristic curves
DL Continuous running n Speed
KB Short operation n0 No-load speed
KBe very short operation nN Rated speed
P Power nKB Speed in short operation
P2N Nominal power at the output shaft nKBe Speed in very short operation
P2max Maximum power at the output shaft I Current
P2KB Power at the output shaft in short I0 No-load currentoperation
IA Startin currentP2KBe Power at the output shaft in very short
operation IN Rated current
M Torque IKB Current in short operation
MA Starting torque IKBe Current in very short operation
MN Nominal torque at the output shaft Efficiency
MKB Torque at the output shaft in short max Maximum efficiencyoperation
N Rated efficiencyMKBe Torque at the output shaft in very
short operation KB Efficiency in short operation
KBe Efficiency in very short operation
Important explanatory informationTolerance zones
7
Tolerance zones
8
Series 0225 (GMPG)DC motors with worm gear
Technical Description
Motor casing: rolled, corrossion protectedExcitation field: PermanentmagnetMethod of bearing, A-side: Sleeve bearingMethod of bearing, B-side: Sleeve bearingGear: Worm gearGear housing: Zinc die castGear wheel: plasticGear greasing: lubricant / permanent lubrication
Mechanic interface: Output shaft or hollow shaft with profileElectric interface: Connector or leads with connector or tinned leads
Encoder: optionalThermal protection: optionalRFI supression: optional
Use
IndustryLinear drivesSmart building technologySeat and furniture adjustmentGeneral machineryVending machinesAgricultural technologyOffice machinesLaboratory devicesMedical technologyTraffic and communications technologyFilm / optics
MotorcarsSeat hight adjustment
9
Series 0225 (GMPG)Motor type 404 157
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 540
Nominal torque MN [Nm] 0,50
ON time % 10
ON [min]
Starting torque MA [Nm] 4,00
Gear ratio i 56/4
Armature resistance, 2 bars R [mΩ] 1300,00
4 bars R [mΩ] 1150,00
Armature inductance, 2 bars L [mH] 0,80
4 bars L [mH] 0,70
Armature load inertia JR [kgm2] × 10-6 9,00
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarksd = for thread-forming screw M 5 DIN 7500
Enclosure class IP 30
Weight [kg] 0,710
404 157
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0.0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6 4.0
0 4 7 11 14 18 21 25 28 32 35
0
2
4
6
8
10
12
14
16
18
20
0
60
120
180
240
300
360
420
480
540
600
n
I
I Tapered splines 7 x 8 DIN 5481 continuous
I Blade terminal ends 4,8 x 0,8 DIN 46 244
II Blade terminal ends 6,3 x 0,8 DIN 46 244
10
Series 0225 (GMPG)Motor type 404 763
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 140
Nominal torque MN [Nm] 2,00
ON time %
ON [min]
Starting torque MA [Nm] 14,00
Gear ratio i 62/1
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material
Hall IC X
Pulses/rev. drive shaft 62
Output channels 2
Remarksd = for thread-forming screw M5 DIN 7500
Enclosure class IP 30
Weight [kg] 0,710
404 763
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 2 4 6 8 10 12 14 16 18 20
0 18 35 53 71 89 106 124 142 159 177
0
3
6
9
12
15
18
21
24
27
30
0
20
40
60
80
100
120
140
160
180
200
n
I
I Tapered splines 7 x 8 DIN 5481 continuous I Terminal 1, OUT A1, grey
II Terminal 2, OUT A2, black
III Terminal 3, + , white
IV Terminal 4, - , red
Notes:
11
Series 0225 (GMPG)Motor type 404 763
I Connector housing AMP 929505-2
II Maiting connector AMP 929504-2
III Motor, blue
IV Motor, violet
12
Series 0225 (GMPG)Motor type 404 603
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 80
Nominal torque MN [Nm] 1,00
ON time % 10
ON [min]
Starting torque MA [Nm] 8,50
Gear ratio i 62/1
Armature resistance, 2 bars R [mΩ] 2700,00
4 bars R [mΩ] 2400,00
Armature inductance, 2 bars L [mH] 2,70
4 bars L [mH] 2,30
Armature load inertia JR [kgm2] × 10-6 10,00
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarksd = for thread-forming screw M 5 DIN 7500
Enclosure class IP 30
Weight [kg] 0,710
404 603
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0.0 0.9 1.8 2.7 3.6 4.5 5.4 6.3 7.2 8.1 9.0
0 8 16 24 32 40 48 56 64 72 80
0
1
2
3
4
5
6
7
8
9
10
0
8
16
24
32
40
48
56
64
72
80
n
I
I Blade terminal ends 4,8 x 0,8 DIN 46 244
II Blade terminal ends 6,3 x 0,8 DIN 46 244
13
Series 0225 (GMPG)Motor type 404 774
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 35
Nominal torque MN [Nm] 1,30
ON time % 10
ON [min]
Starting torque MA [Nm] 7,50
Gear ratio i 72/1
Armature resistance, 2 bars R [mΩ] 5670,00
4 bars R [mΩ] 4200,00
Armature inductance, 2 bars L [mH] 5,65
4 bars L [mH] 3,90
Armature load inertia JR [kgm2] × 10-6
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarksd = for self-tapping screw M5 DIN 7500
Enclosure class IP 30
Weight [kg] 0,570
404 774
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0.0 0.8 1.6 2.4 3.2 4.0 4.8 5.6 6.4 7.2 8.0
0 7 14 21 28 35 42 50 57 64 71
0.0
0.4
0.8
1.2
1.6
2.0
2.4
2.8
3.2
3.6
4.0
0
4
8
12
16
20
24
28
32
36
40
n
I
I Blade terminal ends 4,8 x 0,8 DIN 46 244
II Blade terminal ends 6,3 x 0,8 DIN 46 244
14
Series 0225 (GMPG)Motor type 404 910
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 35
Nominal torque MN [Nm] 1,50
ON time %
ON [min]
Starting torque MA [Nm] 8,00
Gear ratio i 72/1
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material plastic
Hall IC X
Pulses/rev. drive shaft 288
Output channels 1
Remarksd = for thread-forming screw M5 DIN 7500
Enclosure class IP 30
Weight [kg] 0,710
404 910
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0.0 0.8 1.6 2.4 3.2 4.0 4.8 5.6 6.4 7.2 8.0
0 7 14 21 28 35 42 50 57 64 71
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
0
4
8
12
16
20
24
28
32
36
40
n
I
I Terminal 3, + , white
II Terminal 2, - , black
III Terminal 6, OUT, red
Notes:
15
Series 0225 (GMPG)Motor type 404 910
I Terminal Molex Mini-Fit.Jr 39-01-2066
II Pin gold plated 39-00-53
III Pin 1, motor, violet
IV Pin 4, motor, blue
16
Series 0321 (GMPS)DC motors with worm gear
Technical Description
Motor casing: rolled, corrossion protectedExcitation field: PermanentmagnetMethod of bearing, A-side: Sleeve bearingMethod of bearing, B-side: Sleeve bearingGear: Worm gearGear housing: Zinc die castGear wheel: plasticGear greasing: lubricant / permanent lubrication
Mechanic interface: Output shaft or hollow shaft with profileElectric interface: Connector or leads with connector or tinned leads
Encoder: optionalThermal protection: optionalRFI supression: optional
Use
IndustrySmart building technologyGeneral machineryVending machinesAgricultural technologyOffice machinesLaboratory devicesMedical technologyTraffic and communications technologyFilm / optics
MotorcarsSeat hight adjustment
17
Series 0321 (GMPS)Motor type 404 846
Technical DataRated voltage UN [Volt] 12
No-load speed n0 [min-1] 180
Nominal torque MN [Nm] 1,50
ON time % 10
ON [min]
Starting torque MA [Nm] 6,10
Gear ratio i 29/1
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material plastic
Hall IC X
Pulses/rev. drive shaft 29
Output channels 2
Remarks L = 116mm, 1 start worm
Enclosure class IP 40
Weight [kg] 0,880
404 846
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0.0 0.7 1.4 2.1 2.8 3.5 4.2 4.9 5.6 6.3 7.0
0 6 12 19 25 31 37 43 50 56 62
0
3
6
9
12
15
18
21
24
27
30
0
20
40
60
80
100
120
140
160
180
200
n
I
I Shaft 7/16-8 STUB ACME RH I Terminal 1
II Terminal 5
I Terminal 4, Hall-IC +
II Terminal 2, Hall-IC -
18
Notes:
Series 0321 (GMPS)Motor type 404 846
I Terminal housing 5-poleTYCO C-208-15621 (Z)
II Mating connector TYCO 1379217-3 + TYCO 1379218-2
19
Series 0321 (GMPS)Motor type 404 847
Technical DataRated voltage UN [Volt] 12
No-load speed n0 [min-1] 180
Nominal torque MN [Nm] 1,50
ON time % 10
ON [min]
Starting torque MA [Nm] 6,10
Gear ratio i 29/1
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material plastic
Hall IC X
Pulses/rev. drive shaft 29
Output channels 2
Remarks L = 116mm, 1 start worm
Enclosure class IP 40
Weight [kg] 0,880
404 847
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0.0 0.7 1.4 2.1 2.8 3.5 4.2 4.9 5.6 6.3 7.0
0 6 12 19 25 31 37 43 50 56 62
0
3
6
9
12
15
18
21
24
27
30
0
20
40
60
80
100
120
140
160
180
200
n
I
I Shaft 7/16-8 STUB ACME RH I Terminal 1
II Terminal 5
I Terminal 4, Hall-IC +
II Terminal 2, Hall-IC -
20
Notes:
Series 0321 (GMPS)Motor type 404 847
I Terminal housing 5-poleTYCO C-208-15621 (Z)
II Mating connector TYCO 1379217-3 + TYCO 1379218-2
21
Series 0320 (GMPD)DC motors with worm gear
Technical Description
Motor casing: rolled, corrossion protectedExcitation field: PermanentmagnetMethod of bearing, A-side: Sleeve bearingMethod of bearing, B-side: Sleeve bearingGear: Worm gearGear housing: plasticGear wheel: plasticGear greasing: lubricant / permanent lubrication
Mechanic interface: Hollow shaft with profileElectric interface: Connector or leads with connector
Encoder: optionalThermal protection: optionalRFI supression: optional
Use
IndustrySeat and furniture adjustmentSmart building technologyDoor drivesGeneral machineryVending machinesAgricultural technologyOffice machinesLaboratory devicesMedical technologyTraffic and communications technologyFilm / optics
MotorcarsSeat recliner adjustment
22
Series 0320 (GMPD)Motor type 404 747
Technical DataRated voltage UN [Volt] 12
No-load speed n0 [min-1] 21
Nominal torque MN [Nm] 3,00
ON time % 10
ON [min]
Starting torque MA [Nm] 19,60
Gear ratio i 210/1
Armature resistance, 2 bars R [mΩ] 1110,00
4 bars R [mΩ] 630,00
Armature inductance, 2 bars L [mH] 0,90
4 bars L [mH] 0,54
Armature load inertia JR [kgm2] × 10-6 9,50
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks Plastic gearbox
Enclosure class IP 40
Weight [kg] 0,440
404 747
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 2 4 6 8 10 12 14 16 18 20
0 18 35 53 71 89 106 124 142 159 177
0
2
4
6
8
10
12
14
16
18
20
0
3
6
9
12
15
18
21
24
27
30
n
I
I Profile continuous I Terminal 1
II Terminal 5
I Terminal housing 5-poleTYCO C-208-15621 (Z)
II Mating connector TYCO 1379217-3 + TYCO 1379218-2
23
Series 0320 (GMPD)Motor type 404 907
Technical DataRated voltage UN [Volt] 12
No-load speed n0 [min-1] 21
Nominal torque MN [Nm] 2,00
ON time % 10
ON [min]
Starting torque MA [Nm] 18,50
Gear ratio i 210/1
Armature resistance, 2 bars R [mΩ] 1110,00
4 bars R [mΩ] 630,00
Armature inductance, 2 bars L [mH] 0,90
4 bars L [mH] 0,54
Armature load inertia JR [kgm2] × 10-6 9,50
Gear wheel material plastic
Hall IC X
Pulses/rev. drive shaft 210
Output channels 1
Remarks Plastic gearbox
Enclosure class IP 40
Weight [kg] 0,440
404 907
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 2 4 6 8 10 12 14 16 18 20
0 18 35 53 71 89 106 124 142 159 177
0
2
4
6
8
10
12
14
16
18
20
0
3
6
9
12
15
18
21
24
27
30
n
I
I KRC Profile 316928 AEIZ 01 continuous
I Terminal 1
II Terminal 5
I Terminal 4; Hall-IC +
II Terminal 2; Hall-IC -
24
Notes:
Series 0320 (GMPD)Motor type 404 907
I Terminal housing 5-poleTYCO C-208-15621 (Z)
II Mating connector TYCO 1379217-3 + TYCO 1379218-2
25
Series 0320 (GMPD)Motor type 404 748
Technical DataRated voltage UN [Volt] 12
No-load speed n0 [min-1] 21
Nominal torque MN [Nm] 3,00
ON time % 10
ON [min]
Starting torque MA [Nm] 19,60
Gear ratio i 210/1
Armature resistance, 2 bars R [mΩ] 1110,00
4 bars R [mΩ] 630,00
Armature inductance, 2 bars L [mH] 0,90
4 bars L [mH] 0,54
Armature load inertia JR [kgm2] × 10-6 9,50
Gear wheel material plastic
Hall IC X
Pulses/rev. drive shaft 210
Output channels 1
Remarks Plastic gearbox
Enclosure class IP 40
Weight [kg] 0,440
404 748
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 2 4 6 8 10 12 14 16 18 20
0 18 35 53 71 89 106 124 142 159 177
0
2
4
6
8
10
12
14
16
18
20
0
3
6
9
12
15
18
21
24
27
30
n
I
I Profile continuous I Terminal 1
II Terminal 5
I Terminal 4, Hall-IC +
II Terminal 2, Hall-IC -
26
Notes:
Series 0320 (GMPD)Motor type 404 748
I Terminal housing 5-poleTYCO C-208-15621 (Z)
II Mating connector TYCO 1379217-3 + TYCO 1379218-2
27
Series 0320 (GMPD)Motor type 404 904
Technical DataRated voltage UN [Volt] 12
No-load speed n0 [min-1] 21
Nominal torque MN [Nm] 2,00
ON time % 10
ON [min]
Starting torque MA [Nm] 19,50
Gear ratio i 210/1
Armature resistance, 2 bars R [mΩ] 1110,00
4 bars R [mΩ] 630,00
Armature inductance, 2 bars L [mH] 0,90
4 bars L [mH] 0,54
Armature load inertia JR [kgm2] × 10-6 9,50
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks Plastic gearbox
Enclosure class IP 40
Weight [kg] 0,440
404 904
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 2 4 6 8 10 12 14 16 18 20
0 18 35 53 71 89 106 124 142 159 177
0
2
4
6
8
10
12
14
16
18
20
0
3
6
9
12
15
18
21
24
27
30
n
I
I KRC Profile 316928 AEIZ 01 continuous
I Terminal 1
II Terminal 5
I Terminal housing 5-poleTYCO C-208-15621 (Z)
II Mating connector TYCO 1379217-3 + TYCO 1379218-2
28
Series 0320 (GMPD)Motor type 404 905
Technical DataRated voltage UN [Volt] 12
No-load speed n0 [min-1] 21
Nominal torque MN [Nm] 2,00
ON time % 10
ON [min]
Starting torque MA [Nm] 19,50
Gear ratio i 210/1
Armature resistance, 2 bars R [mΩ] 1110,00
4 bars R [mΩ] 630,00
Armature inductance, 2 bars L [mH] 0,90
4 bars L [mH] 0,54
Armature load inertia JR [kgm2] × 10-6 9,50
Gear wheel material plastic
Hall IC X
Pulses/rev. drive shaft 210
Output channels 1
Remarks Plastic gearbox
Enclosure class IP 40
Weight [kg] 0,440
404 905
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 2 4 6 8 10 12 14 16 18 20
0 18 35 53 71 89 106 124 142 159 177
0
2
4
6
8
10
12
14
16
18
20
0
3
6
9
12
15
18
21
24
27
30
n
I
I KRC Profile 316928 AEIZ 01 continuous
I Terminal 1
II Terminal 5
I Terminal 4; Hall-IC +
II Terminal 2; Hall-IC -
Notes:
29
Series 0320 (GMPD)Motor type 404 905
I Terminal housing 5-poleTYCO C-208-15621 (Z)
II Mating connector TYCO 1379217-3 + TYCO 1379218-2
30
Series 0320 (GMPD)Motor type 404 682
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 40
Nominal torque MN [Nm] 4,00
ON time % 10
ON [min]
Starting torque MA [Nm] 34,00
Gear ratio i 210/1
Armature resistance, 2 bars R [mΩ] 1110,00
4 bars R [mΩ] 630,00
Armature inductance, 2 bars L [mH] 0,90
4 bars L [mH] 0,54
Armature load inertia JR [kgm2] × 10-6 9,50
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks
Enclosure class IP 40
Weight [kg] 0,440
404 682
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 4 8 12 16 20 24 28 32 36 40
0 35 71 106 142 177 212 248 283 319 354
0
2
4
6
8
10
12
14
16
18
20
0
4
8
12
16
20
24
28
32
36
40
n
I
I KRC Profile 316928 AEIZ 01 continuous
I Terminal AMP 365057-3Mating connector AMP 365058-3
II Contacts AMP 928781-5Mating contacts AMP 927768-1
III Terminal 1, black
IV Terminal 2, blue
31
Series 0320 (GMPD)Motor type 404 764
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 22
Nominal torque MN [Nm] 4,00
ON time % 10
ON [min]
Starting torque MA [Nm] 22,00
Gear ratio i 210/1
Armature resistance, 2 bars R [mΩ] 5430,00
4 bars R [mΩ] 2980,00
Armature inductance, 2 bars L [mH] 4,10
4 bars L [mH] 2,80
Armature load inertia JR [kgm2] × 10-6 9,50
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks Plastic gearbox
Enclosure class IP 40
Weight [kg] 0,440
404 764
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 3 6 9 12 15 18 21 24 27 30
0 27 53 80 106 133 159 186 212 239 266
0.0
0.6
1.2
1.8
2.4
3.0
3.6
4.2
4.8
5.4
6.0
0
3
6
9
12
15
18
21
24
27
30
n
I
I KRC Profile 316928 AEIZ 01 continuous
I Terminal 1, black
II Terminal 2, blue
I Terminal AMP 365057-1Mating connector AMP 365058-1
II Contacts AMP 928781-5Mating contacts AMP 927768-1
III Terminal 1, black
IV Terminal 2, blue
32
Series 0266 (DCK31)DC motors with worm gear
Technical Description
Motor casing: Deep drawn, corrossion protectedExcitation field: PermanentmagnetMethod of bearing, A-side: Ball bearingMethod of bearing, B-side: Sleeve bearingGear: Worm gearGear housing: Zinc die castGear wheel: plastic, bronze optionalGear greasing: lubricant / permanent lubrication
Mechanic interface: Output shaftElectric interface: Connector
Encoder: optionalThermal protection: optionalRFI supression: optional
Use
IndustryDoor drivesLinear drivesCentralised lubrication systemsMedical technologySmart building technologyGeneral machineryAgricultural technologyLaboratory devicesTraffic and communications technologyFilm / opticsSeat and furniture adjustment
MotorcarsLiftgateSliding doorSeat adjustment
33
Series 0266 (DCK31)Motor type 404 990
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 195
Nominal torque MN [Nm] 3,00
ON time %
ON [min]
Starting torque MA [Nm] 21,00
Gear ratio i 53/2
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material plastic
Hall IC X
Pulses/rev. drive shaft 79,51
Output channels 1
Remarksd = for thread-forming screw M6 DIN ISO 965-2
Enclosure class IP 30
Weight [kg] 1,210
404 990
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 3 6 9 12 15 18 21 24 27 30
0 27 53 80 106 133 159 186 212 239 266
0
3
6
9
12
15
18
21
24
27
30
0
20
40
60
80
100
120
140
160
180
200
n
I
! Lefthhand thread
34
Notes:
Series 0266 (DCK31)Motor type 404 990
I Terminal 3, A
II Terminal 4, +
III Terminal 5, -
I Blade terminals 6.3 x 0.8 DIN 46 244
II Mating connector: Tyco 180907with sleeve AMP 925603
I Mating connector: Panduit CE100 F22 - 03
I Ground connectionBlade terminal 6.3 x 0.8 DIN 46 244
35
Series 0266 (DCK31)Motor type 405 002
Technical DataRated voltage UN [Volt] 12
No-load speed n0 [min-1] 22
Nominal torque MN [Nm] 4,00
ON time %
ON [min]
Starting torque MA [Nm] 37,00
Gear ratio i 69/1
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarksd = for thread-forming screw M6 DIN ISO 965-2
Enclosure class IP 30
Weight [kg] 1,210
405 002
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 4 8 12 16 20 24 28 32 36 40
0 35 71 106 142 177 212 248 283 319 354
0
2
4
6
8
10
12
14
16
18
20
0
3
6
9
12
15
18
21
24
27
30
n
I
I Blade terminals 6.3 x 0.8 DIN 46 244
II Mating connector: Tyco 180907with sleeve AMP 925603
36
Series 0266 (DCK31)Motor type 404 991
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 270
Nominal torque MN [Nm] 1,00
ON time %
ON [min]
Starting torque MA [Nm] 7,50
Gear ratio i 41/4
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material plastic
Hall IC X
Pulses/rev. drive shaft 10,25
Output channels 1
Remarksd = for thread-forming screw M6 DIN ISO 965-2
Enclosure class IP 30
Weight [kg] 1,250
404 991
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0.0 0.8 1.6 2.4 3.2 4.0 4.8 5.6 6.4 7.2 8.0
0 7 14 21 28 35 42 50 57 64 71
0
2
4
6
8
10
12
14
16
18
20
0
30
60
90
120
150
180
210
240
270
300
n
I
I Terminal 3, A
II Terminal 4, +
III Terminal 5, -
Notes:
37
Series 0266 (DCK31)Motor type 404 991
I Blade terminals 6.3 x 0.8 DIN 46 244
II Mating connector: Tyco 180907with sleeve AMP 925603
I Mating connector: Panduit CE100 F22 - 03
I Ground connectionBlade terminal 6.3 x 0.8 DIN 46 244
38
Series 0266 (DCK31)Motor type 404 909
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 165
Nominal torque MN [Nm] 4,00
ON time %
ON [min]
Starting torque MA [Nm] 46,00
Gear ratio i 48/1
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material bronze
Hall IC
Pulses/rev. drive shaftOutput channels
Remarksd = for thread-forming screw M6 DIN ISO 965-2
Enclosure class IP 30
Weight [kg] 1,210
404 909
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 5 10 15 20 25 30 35 40 45 50
0 44 89 133 177 221 266 310 354 398 443
0
7
14
21
28
35
42
49
56
63
70
0
20
40
60
80
100
120
140
160
180
200
n
I
I Tapered splines 8 x 10 (similar DIN 5481)
I Terminal 3, A
II Terminal 4, +
III Terminal 5, -
Notes:
39
Series 0266 (DCK31)Motor type 404 909
I Blade terminals 6.3 x 0.8 DIN 46 244
II Mating connector: Tyco 180907with sleeve AMP 925603
I Mating connector: Panduit CE100 F22 - 03
I Ground connectionBlade terminal 6.3 x 0.8 DIN 46 244
40
Series 0266 (DCK31)Motor type 404 865
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 75
Nominal torque MN [Nm] 4,00
ON time %
ON [min]
Starting torque MA [Nm] 49,00
Gear ratio i 69/1
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material plastic
Hall IC X
Pulses/rev. drive shaft 69
Output channels 2
Remarksd = for thread-forming screw M 6 DIN ISO 965-2
Enclosure class IP 30
Weight [kg] 1,210
404 865
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 5 10 15 20 25 30 35 40 45 50
0 44 89 133 177 221 266 310 354 398 443
0
4
8
12
16
20
24
28
32
36
40
0
8
16
24
32
40
48
56
64
72
80
n
I
I Hall-IC A1, terminal 3
II Hall-IC A2, terminal 4
III Hall-IC +, terminal 5
IV Hall-IC -, terminal 6
Notes:
41
Series 0266 (DCK31)Motor type 404 865
I Blade terminals 6.3 x 0.8 DIN 46 244
II Mating connector: Tyco 180907with sleeve AMP 925603
I Mating connector: Panduit CE100 F22 - 04
I Ground connectionBlade terminal 6.3 x 0.8 DIN 46 244
42
Series 0266 (DCK31)Motor type 404 864
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 66
Nominal torque MN [Nm] 4,00
ON time %
ON [min]
Starting torque MA [Nm] 50,00
Gear ratio i 69/1
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarksd = for thread-forming screw M6 DIN ISO 965-2
Enclosure class IP 30
Weight [kg] 1,210
404 864
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 5 10 15 20 25 30 35 40 45 50
0 44 89 133 177 221 266 310 354 398 443
0
3
6
9
12
15
18
21
24
27
30
0
7
14
21
28
35
42
49
56
63
70
n
I
I Circlip
I Blade terminals 6.3 x 0.8 DIN 46 244
II Mating connector: Tyco 180907with sleeve AMP 925603
43
Series 0266 (DCK31)Motor type 404 853
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 65
Nominal torque MN [Nm] 4,00
ON time %
ON [min]
Starting torque MA [Nm] 50,00
Gear ratio i 69/1
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarksd = for thread-forming screw M6 DIN ISO 965-2
Enclosure class IP 30
Weight [kg] 1,210
404 853
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 5 10 15 20 25 30 35 40 45 50
0 44 89 133 177 221 266 310 354 398 443
0
3
6
9
12
15
18
21
24
27
30
0
7
14
21
28
35
42
49
56
63
70
n
I
I Tapered splines 8 x 10 (similar DIN 5481)
II Circlip
I Blade terminals 6.3 x 0.8 DIN 46 244
II Mating connector: Tyco 180907with sleeve AMP 925603
44
Series 0266 (DCK31)Motor type 405 006
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 65
Nominal torque MN [Nm] 4,00
ON time %
ON [min]
Starting torque MA [Nm] 50,00
Gear ratio i 69/1
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material plastic
Hall IC X
Pulses/rev. drive shaft 69
Output channels 2
Remarksd = for thread-forming screw M6 DIN ISO 965-2
Enclosure class IP 30
Weight [kg] 1,250
405 006
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 5 10 15 20 25 30 35 40 45 50
0 44 89 133 177 221 266 310 354 398 443
0
3
6
9
12
15
18
21
24
27
30
0
7
14
21
28
35
42
49
56
63
70
n
I
I Tapered splines 8 x 10 (similar DIN 5481)
I Hall-IC A1, terminal 3
II Hall-IC A2, terminal 4
III Hall-IC +, terminal 5
IV Hall-IC -, terminal 6
Notes:
45
Series 0266 (DCK31)Motor type 405 006
I Blade terminals 6.3 x 0.8 DIN 46 244
II Mating connector: Tyco 180907with sleeve AMP 925603
I Mating connector: Panduit CE100 F22 - 04
I Ground connectionBlade terminal 6.3 x 0.8 DIN 46 244
46
Series 0266 (DCK31)Motor type 404 866
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 48
Nominal torque MN [Nm] 4,00
ON time %
ON [min]
Starting torque MA [Nm] 26,00
Gear ratio i 69/1
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarksd = for thread-forming screw M6 DIN ISO 965-2
Enclosure class IP 30
Weight [kg] 1,210
404 866
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 3 6 9 12 15 18 21 24 27 30
0 27 53 80 106 133 159 186 212 239 266
0
3
6
9
12
15
18
21
24
27
30
0
5
10
15
20
25
30
35
40
45
50
n
I
I Tapered splines 8 x 10 (similar DIN 5481)
! Only for connection of encoder
Notes:
47
Series 0266 (DCK31)Motor type 404 866
I Blade terminals 6.3 x 0.8 DIN 46 244
II Mating connector: Tyco 180907with sleeve AMP 925603
48
Series 0266 (DCK31)Motor type 404 854
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 65
Nominal torque MN [Nm] 4,00
ON time %
ON [min]
Starting torque MA [Nm] 50,00
Gear ratio i 69/1
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material plastic
Hall IC X
Pulses/rev. drive shaft 69
Output channels 1
Remarksd = for thread-forming screw M6 DIN ISO 965-2
Enclosure class IP 30
Weight [kg] 1,250
404 854
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 5 10 15 20 25 30 35 40 45 50
0 44 89 133 177 221 266 310 354 398 443
0
3
6
9
12
15
18
21
24
27
30
0
7
14
21
28
35
42
49
56
63
70
n
I
I Tapered splines 8 x 10 (similar DIN 5481)
I Terminal 3, A
II Terminal 4, +
III Terminal 5, -
Notes:
49
Series 0266 (DCK31)Motor type 404 854
I Blade terminals 6.3 x 0.8 DIN 46 244
II Mating connector: Tyco 180907with sleeve AMP 925603
I Mating connector: Panduit CE100 F22 - 03
I Ground connectionBlade terminal 6.3 x 0.8 DIN 46 244
50
Series 0266 (DCK31)Motor type 404 988
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 36
Nominal torque MN [Nm] 4,00
ON time %
ON [min]
Starting torque MA [Nm] 27,50
Gear ratio i 69/1
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material plastic
Hall IC X
Pulses/rev. drive shaft 69
Output channels 1
Remarksd = for thread-forming screw M6 DIN ISO 965-2
Enclosure class IP 30
Weight [kg] 1,210
404 988
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 3 6 9 12 15 18 21 24 27 30
0 27 53 80 106 133 159 186 212 239 266
0
2
4
6
8
10
12
14
16
18
20
0
4
8
12
16
20
24
28
32
36
40
n
I
! Lefthhand thread
Notes:
51
Series 0266 (DCK31)Motor type 404 988
I Terminal 3, A
II Terminal 4, +
III Terminal 5, -
I Blade terminals 6.3 x 0.8 DIN 46 244
II Mating connector: Tyco 180907with sleeve AMP 925603
I Mating connector: Panduit CE100 F22 - 03
I Ground connectionBlade terminal 6.3 x 0.8 DIN 46 244
52
Series 0266 (DCK31)Motor type 404 867
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 35
Nominal torque MN [Nm] 6,00
ON time %
ON [min]
Starting torque MA [Nm] 48,00
Gear ratio i 69/1
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarksd = for thread-forming screw M6 DIN ISO 965-2
Enclosure class IP 30
Weight [kg] 1,210
404 867
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 5 10 15 20 25 30 35 40 45 50
0 44 89 133 177 221 266 310 354 398 443
0
2
4
6
8
10
12
14
16
18
20
0
4
8
12
16
20
24
28
32
36
40
n
I
! Lefthhand thread
Notes:
53
Series 0266 (DCK31)Motor type 404 867
I Blade terminals 6.3 x 0.8 DIN 46 244
II Mating connector: Tyco 180907with sleeve AMP 925603
54
Series 0266 (DCK31)Motor type 404 872
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 30
Nominal torque MN [Nm] 4,00
ON time %
ON [min]
Starting torque MA [Nm] 29,00
Gear ratio i 69/1
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarksd = for thread-forming screw M6 DIN ISO 965-2
Enclosure class IP 30
Weight [kg] 1,210
404 872
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 3 6 9 12 15 18 21 24 27 30
0 27 53 80 106 133 159 186 212 239 266
0
1
2
3
4
5
6
7
8
9
10
0
3
6
9
12
15
18
21
24
27
30
n
I
I Blade terminals 6.3 x 0.8 DIN 46 244
II Mating connector: Tyco 180907with sleeve AMP 925603
55
Series 0266 (DCK31)Motor type 404 868
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 22
Nominal torque MN [Nm] 4,00
ON time %
ON [min]
Starting torque MA [Nm] 37,00
Gear ratio i 69/1
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarksd = for thread-forming screw M6 DIN ISO 965-2
Enclosure class IP 30
Weight [kg] 1,210
404 868
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 4 8 12 16 20 24 28 32 36 40
0 35 71 106 142 177 212 248 283 319 354
0
1
2
3
4
5
6
7
8
9
10
0
3
6
9
12
15
18
21
24
27
30
n
I
I Blade terminals 6.3 x 0.8 DIN 46 244
II Mating connector: Tyco 180907with sleeve AMP 925603
56
Series 0266 (DCK31)Motor type 404 987
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 14
Nominal torque MN [Nm] 3,00
ON time %
ON [min]
Starting torque MA [Nm] 16,50
Gear ratio i 78/1
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material bronze
Hall IC X
Pulses/rev. drive shaft 234
Output channels 1
Remarksd = for thread-forming screw M6 DIN ISO 965-2
Enclosure class IP 30
Weight [kg] 1,210
404 987
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 2 4 6 8 10 12 14 16 18 20
0 18 35 53 71 89 106 124 142 159 177
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
0
2
4
6
8
10
12
14
16
18
20
n
I
! Lefthhand thread
Notes:
57
Series 0266 (DCK31)Motor type 404 987
I Terminal 3, A
II Terminal 4, +
III Terminal 5, -
I Blade terminals 6.3 x 0.8 DIN 46 244
II Mating connector: Tyco 180907with sleeve AMP 925603
I Mating connector: Panduit CE100 F22 - 03
I Ground connectionBlade terminal 6.3 x 0.8 DIN 46 244
58
Series 0270 (SWMK)DC motors with worm gear
Technical Description
Motor casing: rolled, corrossion protectedExcitation field: PermanentmagnetMethod of bearing, A-side: Ball bearingMethod of bearing, B-side: Sleeve bearingGear: Worm gearGear housing: Aluninium die castGear wheel: plasticGear greasing: lubricant / permanent lubrication
Mechanic interface: Output shaftElectric interface: Leads with connector or tinned leads
Encoder: optionalThermal protection: optionalRFI supression: optional
Use
IndustryLinear drivesGeneral machineryVending machinesAgricultural technologyOffice machinesLaboratory devicesMedical technologyTraffic and communications technologyFilm / optics
59
Series 0270 (SWMK)Motor type 403 474
Technical DataRated voltage UN [Volt] 12
No-load speed n0 [min-1] 350
Nominal torque MN [Nm] 0,80
ON time %
ON [min]
Starting torque MA [Nm] 10,00
Gear ratio i 41/4
Armature resistance, 2 bars R [mΩ] 210,00
4 bars R [mΩ] 185,00
Armature inductance, 2 bars L [mH] 0,40
4 bars L [mH] 0,35
Armature load inertia JR [kgm2] × 10-6 68,00
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks
Enclosure class IP 30
Weight [kg] 1,200
403 474
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 1 2 3 4 5 6 7 8 9 10
0 9 18 27 35 44 53 62 71 80 89
0
5
10
15
20
25
30
35
40
45
50
0
40
80
120
160
200
240
280
320
360
400
n
I
I Blade terminal ends 6,3 x 0,8 DIN 46 244
II green
III red
60
Series 0270 (SWMK)Motor type 403 475
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 350
Nominal torque MN [Nm] 0,80
ON time %
ON [min]
Starting torque MA [Nm] 10,00
Gear ratio i 41/4
Armature resistance, 2 bars R [mΩ] 750,00
4 bars R [mΩ] 670,00
Armature inductance, 2 bars L [mH] 1,10
4 bars L [mH] 1,00
Armature load inertia JR [kgm2] × 10-6 67,00
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks
Enclosure class IP 30
Weight [kg] 1,200
403 475
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 1 2 3 4 5 6 7 8 9 10
0 9 18 27 35 44 53 62 71 80 89
0
3
6
9
12
15
18
21
24
27
30
0
40
80
120
160
200
240
280
320
360
400
n
I
I Blade terminal ends 6,3 x 0,8 DIN 46 244
II green
III red
61
Series 0268 (DCK35)DC motors with worm gear
Technical Description
Motor casing: Deep drawn, corrossion protectedExcitation field: PermanentmagnetMethod of bearing, A-side: Ball bearingMethod of bearing, B-side: Sleeve bearingGear: Worm gearGear housing: Zinc die castGear wheel: plasticGear greasing: lubricant / permanent lubrication
Mechanic interface: Output shaftElectric interface: Connector
Encoder: optionalThermal protection: optionalRFI supression: optional
Use
IndustryDoor drivesGaragentoröffnerCentralised lubrication systems
MotorcarsLiftgateBetätigung KofferraumdeckelSliding door
62
Series 0268 (DCK35)Motor type 404 983
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 70
Nominal torque MN [Nm] 5,00
ON time %
ON [min]
Starting torque MA [Nm] 59,00
Gear ratio i 55/1
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarksd = for thread-forming screw M6 DIN ISO 965-2
Enclosure class IP 40
Weight [kg] 1,250
404 983
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 6 12 18 24 30 36 42 48 54 60
0 53 106 159 212 266 319 372 425 478 531
0
4
8
12
16
20
24
28
32
36
40
0
7
14
21
28
35
42
49
56
63
70
n
I
I Blade terminals 6.3 x 0.8 DIN 46 244
II Mating connector: Tyco 180907with sleeve AMP 925603
63
Series 0268 (DCK35)Motor type 404 885
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 62
Nominal torque MN [Nm] 5,00
ON time %
ON [min]
Starting torque MA [Nm] 60,00
Gear ratio i 63/1
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material plastic
Hall IC X
Pulses/rev. drive shaft 63
Output channels 2
Remarksd = for thread-forming screw M6 DIN ISO 965-2
Enclosure class IP 30
Weight [kg] 1,250
404 885 η/%
M/Nmin-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 6 12 18 24 30 36 42 48 54 600 53 106 159 212 266 319 372 425 478 531
0
5
10
15
20
25
30
35
40
45
50
0
7
14
21
28
35
42
49
56
63
70
n
η
I
I Tapered splines 8 x 10 (similar DIN 5481)
I Hall-IC A1, terminal 3
II Hall-IC A2, terminal 4
III Hall-IC +, terminal 5
IV Hall-IC -, terminal 6
64
Notes:
Series 0268 (DCK35)Motor type 404 885
I Blade terminals 6.3 x 0.8 DIN 46 244
II Mating connector: Tyco 180907with sleeve AMP 925603
I Hall-IC A1, terminal 3
II Hall-IC A2, terminal 4
III Hall-IC +, terminal 5
IV Hall-IC -, terminal 6
V Mating connector: Panduit CE100 F22 - 04
I Ground connectionBlade terminal 6.3 x 0.8 DIN 46 244
65
Series 0277 (SW2K)DC motors with worm gear
Technical Description
Motor casing: Deep drawn, corrossion protectedExcitation field: PermanentmagnetMethod of bearing, A-side: Ball bearing, sleeve bearing optionalMethod of bearing, B-side: Sleeve bearingGear: Worm gearGear housing: Aluninium die castGear wheel: plasticGear greasing: lubricant / permanent lubrication
Mechanic interface: Output shaftElectric interface: Connector
Encoder: optionalThermal protection: optionalRFI supression: optional
Use
IndustryLinear drivesGeneral machineryVending machinesAgricultural technologyOffice machinesLaboratory devicesMedical technologyTraffic and communications technologyFilm / optics
66
Series 0277 (SW2K)Motor type 404 925
Technical DataRated voltage UN [Volt] 12
No-load speed n0 [min-1] 270
Nominal torque MN [Nm] 3,00
ON time %
ON [min]
Starting torque MA [Nm] 16,00
Gear ratio i 70/4
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks Ball bearing
Enclosure class IP 40
Weight [kg] 1,200
404 925
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 2 4 6 8 10 12 14 16 18 20
0 18 35 53 71 89 106 124 142 159 177
0
6
12
18
24
30
36
42
48
54
60
0
30
60
90
120
150
180
210
240
270
300
n
I
I Tapered splines 8 x 10 f(similar DIN 5481)
I Blade terminal ends 6,3 x 0,8 DIN 46 244
II Blade terminal ends 4,8 x 0,8 DIN 46 244
67
Series 0277 (SW2K)Motor type 403 933
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 230
Nominal torque MN [Nm] 2,00
ON time %
ON [min]
Starting torque MA [Nm] 24,00
Gear ratio i 70/4
Armature resistance, 2 bars R [mΩ] 520,00
4 bars R [mΩ] 430,00
Armature inductance, 2 bars L [mH] 0,96
4 bars L [mH] 0,88
Armature load inertia JR [kgm2] × 10-6 78,00
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks Ball bearing
Enclosure class IP 40
Weight [kg] 1,200
403 933
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 3 6 9 12 15 18 21 24 27 30
0 27 53 80 106 133 159 186 212 239 266
0
4
8
12
16
20
24
28
32
36
40
0
30
60
90
120
150
180
210
240
270
300
n
I
! Lefthhand thread
68
Notes:
Series 0277 (SW2K)Motor type 403 933
I Blade terminal ends 6,3 x 0,8 DIN 46 244
II Blade terminal ends 4,8 x 0,8 DIN 46 244
69
Series 0277 (SW2K)Motor type 403 930
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 230
Nominal torque MN [Nm] 2,00
ON time %
ON [min]
Starting torque MA [Nm] 24,00
Gear ratio i 70/4
Armature resistance, 2 bars R [mΩ] 520,00
4 bars R [mΩ] 430,00
Armature inductance, 2 bars L [mH] 0,96
4 bars L [mH] 0,88
Armature load inertia JR [kgm2] × 10-6 78,00
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks Ball bearing
Enclosure class IP 40
Weight [kg] 1,200
403 930
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 3 6 9 12 15 18 21 24 27 30
0 27 53 80 106 133 159 186 212 239 266
0
4
8
12
16
20
24
28
32
36
40
0
30
60
90
120
150
180
210
240
270
300
n
I
! Lefthhand thread
70
Notes:
Series 0277 (SW2K)Motor type 403 930
I Blade terminal ends 6,3 x 0,8 DIN 46 244
II Blade terminal ends 4,8 x 0,8 DIN 46 244
71
Series 0277 (SW2K)Motor type 403 931
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 126
Nominal torque MN [Nm] 2,00
ON time %
ON [min]
Starting torque MA [Nm] 15,50
Gear ratio i 70/4
Armature resistance, 2 bars R [mΩ] 2100,00
4 bars R [mΩ] 1700,00
Armature inductance, 2 bars L [mH] 3,60
4 bars L [mH] 3,25
Armature load inertia JR [kgm2] × 10-6 72,00
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks Ball bearing
Enclosure class IP 40
Weight [kg] 1,200
403 931
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 2 4 6 8 10 12 14 16 18 20
0 18 35 53 71 89 106 124 142 159 177
0
2
4
6
8
10
12
14
16
18
20
0
20
40
60
80
100
120
140
160
180
200
n
I
! Lefthhand thread
72
Notes:
Series 0277 (SW2K)Motor type 403 931
I Blade terminal ends 6,3 x 0,8 DIN 46 244
II Blade terminal ends 4,8 x 0,8 DIN 46 244
73
Series 0277 (SW2K)Motor type 403 936
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 54
Nominal torque MN [Nm] 5,00
ON time %
ON [min]
Starting torque MA [Nm] 71,00
Gear ratio i 78/1
Armature resistance, 2 bars R [mΩ] 520,00
4 bars R [mΩ] 420,00
Armature inductance, 2 bars L [mH] 0,96
4 bars L [mH] 0,85
Armature load inertia JR [kgm2] × 10-6 72,00
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks
Enclosure class IP 40
Weight [kg] 1,200
403 936
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 8 16 24 32 40 48 56 64 72 80
0 71 142 212 283 354 425 496 566 637 708
0
4
8
12
16
20
24
28
32
36
40
0
6
12
18
24
30
36
42
48
54
60
n
I
I Blade terminal ends 6,3 x 0,8 DIN 46 244
II Blade terminal ends 4,8 x 0,8 DIN 46 244
74
Series 0278 (SW2L)DC motors with worm gear
Technical Description
Motor casing: Deep drawn, corrossion protectedExcitation field: PermanentmagnetMethod of bearing, A-side: Ball bearingMethod of bearing, B-side: Sleeve bearingGear: Worm gearGear housing: Aluninium die castGear wheel: plasticGear greasing: lubricant / permanent lubrication
Mechanic interface: Output shaftElectric interface: Connector
Encoder: optionalThermal protection: optionalRFI supression: optional
Use
IndustryDoor drivesLinear drivesFurniture adjusterSmart building technology
75
Series 0278 (SW2L)Motor type 404 385
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 190
Nominal torque MN [Nm] 4,00
ON time %
ON [min]
Starting torque MA [Nm] 49,00
Gear ratio i 103/4
Armature resistance, 2 bars R [mΩ] 210,00
4 bars R [mΩ] 155,00
Armature inductance, 2 bars L [mH] 0,50
4 bars L [mH] 0,45
Armature load inertia JR [kgm2] × 10-6 85,00
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks
Enclosure class IP 40
Weight [kg] 1,700
404 385
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 5 10 15 20 25 30 35 40 45 50
0 44 89 133 177 221 266 310 354 398 443
0
6
12
18
24
30
36
42
48
54
60
0
20
40
60
80
100
120
140
160
180
200
n
I
! Lefthhand thread
76
Notes:
Series 0278 (SW2L)Motor type 404 385
I Blade terminal ends 6,3 x 0,8 DIN 46 244
II Blade terminal ends 4,8 x 0,8 DIN 46 244
77
Series 0278 (SW2L)Motor type 404 386
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 190
Nominal torque MN [Nm] 4,00
ON time %
ON [min]
Starting torque MA [Nm] 49,00
Gear ratio i 103/4
Armature resistance, 2 bars R [mΩ] 210,00
4 bars R [mΩ] 155,00
Armature inductance, 2 bars L [mH] 0,50
4 bars L [mH] 0,45
Armature load inertia JR [kgm2] × 10-6 85,00
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks
Enclosure class IP 40
Weight [kg] 1,700
404 386
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 5 10 15 20 25 30 35 40 45 50
0 44 89 133 177 221 266 310 354 398 443
0
6
12
18
24
30
36
42
48
54
60
0
20
40
60
80
100
120
140
160
180
200
n
I
! Lefthhand thread
78
Notes:
Series 0278 (SW2L)Motor type 404 386
I Blade terminal ends 6,3 x 0,8 DIN 46 244
II Blade terminal ends 4,8 x 0,8 DIN 46 244
79
Series 0278 (SW2L)Motor type 404 360
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 48
Nominal torque MN [Nm] 8,00
ON time %
ON [min]
Starting torque MA [Nm] 83,00
Gear ratio i 74/1
Armature resistance, 2 bars R [mΩ] 670,00
4 bars R [mΩ] 525,00
Armature inductance, 2 bars L [mH] 0,89
4 bars L [mH] 0,79
Armature load inertia JR [kgm2] × 10-6 96,00
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks with spring washer
Enclosure class IP 40
Weight [kg] 1,700
404 360
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 9 18 27 36 45 54 63 72 81 90
0 80 159 239 319 398 478 558 637 717 797
0
4
8
12
16
20
24
28
32
36
40
0
5
10
15
20
25
30
35
40
45
50
n
I
I Blade terminal ends 6,3 x 0,8 DIN 46 244
II Blade terminal ends 4,8 x 0,8 DIN 46 244
80
Series 0291 (SWMV)DC motors with worm gear
Technical Description
Motor casing: rolled, corrossion protectedExcitation field: PermanentmagnetMethod of bearing, A-side: Ball bearingMethod of bearing, B-side: Sleeve bearingGear: Worm gearGear housing: Zinc die castGear wheel: plastic or resin bond fabrics or bronzeGear greasing: lubricant / permanent lubrication
Mechanic interface: Output shaftElectric interface: Connector or leads with connector or tinned leads
Encoder: ---Thermal protection: optionalRFI supression: optional
Use
IndustryGeneral machineryVending machinesAgricultural technologyOffice machinesLaboratory devicesMedical technologyFilm / opticsCleaning machinesPrinting machines
81
Series 0291 (SWMV)Motor type 402 826
Technical DataRated voltage UN [Volt] 12
No-load speed n0 [min-1] 52
Nominal torque MN [Nm] 6,00
ON time %
ON [min]
Starting torque MA [Nm] 65,00
Gear ratio i 59/1
Armature resistance, 2 bars R [mΩ] 220,00
4 bars R [mΩ] 170,00
Armature inductance, 2 bars L [mH] 0,42
4 bars L [mH] 0,38
Armature load inertia JR [kgm2] × 10-6 390,00
Gear wheel material Resinbonded fabric
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks d = M6x16mm
Enclosure class IP 20
Weight [kg] 2,900
402 826
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 7 14 21 28 35 42 49 56 63 70
0 62 124 186 248 310 372 434 496 558 620
0
6
12
18
24
30
36
42
48
54
60
0
6
12
18
24
30
36
42
48
54
60
n
I
I Blade terminal ends 6,3 x 0,8 DIN 46 244
II Terminal 53
III Terminal 31 (ground)
82
Series 0291 (SWMV)Motor type 402 525
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 78
Nominal torque MN [Nm] 8,00
ON time %
ON [min]
Starting torque MA [Nm] 76,00
Gear ratio i 46/1
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material Resinbonded fabric
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks d = M6x16mm
Enclosure class IP 20
Weight [kg] 2,900
402 525
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 8 16 24 32 40 48 56 64 72 80
0 71 142 212 283 354 425 496 566 637 708
0
5
10
15
20
25
30
35
40
45
50
0
8
16
24
32
40
48
56
64
72
80
n
I
I Blade terminal ends 6,3 x 0,8 DIN 46 244
II Terminal 53
III Terminal 31 (ground)
83
Series 0291 (SWMV)Motor type 403 334
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 220
Nominal torque MN [Nm] 3,10
ON time %
ON [min]
Starting torque MA [Nm] 60,00
Gear ratio i 44/2
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks d = M8 x 16 mm
Enclosure class IP 20
Weight [kg] 2,900
403 334
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 6 12 18 24 30 36 42 48 54 60
0 53 106 159 212 266 319 372 425 478 531
0
8
16
24
32
40
48
56
64
72
80
0
30
60
90
120
150
180
210
240
270
300
n
I
I red
II green
84
Series 0291 (SWMV)Motor type 403 362
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 52
Nominal torque MN [Nm] 5,00
ON time %
ON [min]
Starting torque MA [Nm] 90,00
Gear ratio i 59/1
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material Resinbonded fabric
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks d = M8 x 23mm
Enclosure class IP 20
Weight [kg] 2,900
403 362
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 9 18 27 36 45 54 63 72 81 90
0 80 159 239 319 398 478 558 637 717 797
0
5
10
15
20
25
30
35
40
45
50
0
6
12
18
24
30
36
42
48
54
60
n
I
I Blade terminal ends 6,3 x 0,8 DIN 46 244
II Terminal 53
III Terminal 31 (ground)
IV Maiting connector AMP 163 006-1
85
Series 0292 (SWMG)DC motors with worm gear
Technical Description
Motor casing: rolled, corrossion protectedExcitation field: PermanentmagnetMethod of bearing, A-side: Ball bearingMethod of bearing, B-side: Sleeve bearingGear: Worm gearGear housing: Zinc die castGear wheel: plastic or resin bond fabricsGear greasing: lubricant / permanent lubrication
Mechanic interface: Output shaftElectric interface: Leads with connector or tinned leads
Encoder: ---Thermal protection: optionalRFI supression: optional
Use
IndustryMaterial-handling technologyConstruction technologyLaboratory devicesOffice machinesCleaning machines
86
Series 0292 (SWMG)Motor type 402 853
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 27
Nominal torque MN [Nm] 20,00
ON time %
ON [min]
Starting torque MA [Nm] 90,00
Gear ratio i 50/1
Armature resistance, 2 bars R [mΩ] 900,00
4 bars R [mΩ] 800,00
Armature inductance, 2 bars L [mH] 4,20
4 bars L [mH] 3,70
Armature load inertia JR [kgm2] × 10-6 520,00
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks
Enclosure class IP 20
Weight [kg] 4,200
402 853
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 9 18 27 36 45 54 63 72 81 90
0 80 159 239 319 398 478 558 637 717 797
0
3
6
9
12
15
18
21
24
27
30
0
3
6
9
12
15
18
21
24
27
30
n
I
I Groove for key A 5x3x12 DIN 6885
87
Series 0292 (SWMG)Motor type 403 460
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 165
Nominal torque MN [Nm] 10,00
ON time %
ON [min]
Starting torque MA [Nm] 100,00
Gear ratio i 43/3
Armature resistance, 2 bars R [mΩ] 240,00
4 bars R [mΩ] 220,00
Armature inductance, 2 bars L [mH] 0,60
4 bars L [mH] 0,53
Armature load inertia JR [kgm2] × 10-6 690,00
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks
Enclosure class IP 20
Weight [kg] 4,200
403 460
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 10 20 30 40 50 60 70 80 90 100
0 89 177 266 354 443 531 620 708 797 885
0
20
40
60
80
100
120
140
160
180
200
0
20
40
60
80
100
120
140
160
180
200
n
I
88
Series 0231 (GMPI)DC motors with spur gear
Technical Description
Motor casing: rolled, corrossion protectedExcitation field: PermanentmagnetMethod of bearing, A-side: Sleeve bearingMethod of bearing, B-side: Sleeve bearingGear: Spur gearGear housing: plasticGear wheel: plasticGear greasing: lubricant / permanent lubrication
Mechanic interface: Output shaftElectric interface: Connector or leads with connector
Encoder: optionalThermal protection: optionalRFI supression: optional
Use
IndustryLinear drivesGeneral machineryMedical technology
MotorcarsSpoiler adjustment
89
Series 0231 (GMPI)Motor type 404 636
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 155
Nominal torque MN [Nm] 1,50
ON time % 10
ON [min]
Starting torque MA [Nm] 3,50
Gear ratio i 20/1
Armature resistance, 2 bars R [mΩ] 4550,00
4 bars R [mΩ] 3450,00
Armature inductance, 2 bars L [mH] 3,75
4 bars L [mH] 3,11
Armature load inertia JR [kgm2] × 10-6
Gear wheel material plastic
Hall IC X
Pulses/rev. drive shaft 20
Output channels 2
Remarksd = 3,3mm, for self-cutting screw 4mm
Enclosure class IP 50
Weight [kg] 0,750
404 636
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0.0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6 4.0
0 4 7 11 14 18 21 25 28 32 35
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
0
20
40
60
80
100
120
140
160
180
200
n
I
I Terminal 1, A1, grey
II Terminal 2, A2, black
III Terminal 3, + , white
IV Terminal 4, - , red
90
Notes:
Series 0231 (GMPI)Motor type 404 636
I Molex Housing SPOX 09-50-1061
II Molex contacts SPOX 05-70-1031
III Mol. Connector SPOX 26-48-1066
IV Terminal 5, violet, motor
V Terminal 6, blue, motor
91
Series 0231 (GMPI)Motor type 404 465
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 210
Nominal torque MN [Nm] 4,00
ON time % 10
ON [min]
Starting torque MA [Nm] 19,50
Gear ratio i 39,7/1
Armature resistance, 2 bars R [mΩ] 562,00
4 bars R [mΩ] 420,00
Armature inductance, 2 bars L [mH] 0,60
4 bars L [mH] 0,48
Armature load inertia JR [kgm2] × 10-6 13,00
Gear wheel material plastic
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks d = 3,3mm, for self-cutting screw 4mm
Enclosure class IP 50
Weight [kg] 0,630
404 465
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 2 4 6 8 10 12 14 16 18 20
0 18 35 53 71 89 106 124 142 159 177
0
3
6
9
12
15
18
21
24
27
30
0
30
60
90
120
150
180
210
240
270
300
n
I
I Blade terminal ends 4,8 x 0,8 DIN 46 244
II Blade terminal ends 6,3 x 0,8 DIN 46 244
92
Series 0231 (GMPI)Motor type 404 722
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 200
Nominal torque MN [Nm] 4,00
ON time % 10
ON [min]
Starting torque MA [Nm] 24,00
Gear ratio i 39,7/1
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material plastic
Hall IC X
Pulses/rev. drive shaft 39,7
Output channels 2
Remarks d = 3,3mm, for self-cutting screw 4mm
Enclosure class IP 50
Weight [kg] 0,650
404 722
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0 3 6 9 12 15 18 21 24 27 30
0 27 53 80 106 133 159 186 212 239 266
0
4
8
12
16
20
24
28
32
36
40
0
20
40
60
80
100
120
140
160
180
200
n
I
I Terminal 1, OUT A1, grey
II Terminal 2, OUT A2, black
III Terminal 3, + , white
IV Terminal 4, - , red
Notes:
93
Series 0231 (GMPI)Motor type 404 722
I Terminal 1, motor, violet
II Terminal 2, motor, blue
94
Series 0220 (GMP)Plain DC motors
Technical Description
Motor casing: rolled, corrossion protectedExcitation field: PermanentmagnetMethod of bearing, A-side: Ball bearing or Sleeve bearingMethod of bearing, B-side: Sleeve bearingGear: ---Gear housing: ---Gear wheel: ---Gear greasing: ---
Mechanic interface: Output shaftElectric interface: Connector or leads with connector or tinned leads
Encoder: optionalThermal protection: optionalRFI supression: optional
Use
IndustryLinear drivesLaboratory devicesSmart building technologyPumpsVending machinesMedical technologyTraffic and communications technologyLeisure devicesDIYOffice machinesFilm / optics
MotorcarsSeat track adjudtment
95
Series 0220 (GMP)Motor type 404 476
Technical DataRated voltage UN [Volt] 12
No-load speed n0 [min-1] 3250
Nominal torque MN [Nm] 0,05
ON time %
ON [min]
Starting torque MA [Nm] 0,28
Gear ratio i
Armature resistance, 2 bars R [mΩ] 1320,00
4 bars R [mΩ] 680,00
Armature inductance, 2 bars L [mH] 1,15
4 bars L [mH] 0,86
Armature load inertia JR [kgm2] × 10-6 13,70
Gear wheel material
Hall IC X
Pulses/rev. drive shaft 2
Output channels 1
Remarks
Enclosure class IP 40
Weight [kg] 0,520
404 476
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
0.0 0.9 1.8 2.7 3.5 4.4 5.3 6.2 7.1 8.0 8.9
0
2
4
6
8
10
12
14
16
18
20
0
400
800
1200
1600
2000
2400
2800
3200
3600
4000
n
I
I Tapered splines 5 x 6 DIN 5481 I Terminal 1, green
II Terminal 2, black
I Terminal 3, + , red
II Terminal 4, - , brown
96
Notes:
Series 0220 (GMP)Motor type 404 476
I Terminal 1, motor, green
II Terminal 2, motor, black
III Terminal 3, Hall-IC + , red
IV Terminal 4, Hall-IC - , brown
97
Series 0220 (GMP)Motor type 404 743
Technical DataRated voltage UN [Volt] 12
No-load speed n0 [min-1] 2700
Nominal torque MN [Nm] 0,10
ON time %
ON [min]
Starting torque MA [Nm] 0,40
Gear ratio i
Armature resistance, 2 bars R [mΩ] 800,00
4 bars R [mΩ] 440,00
Armature inductance, 2 bars L [mH] 0,72
4 bars L [mH] 0,51
Armature load inertia JR [kgm2] × 10-6 18,00
Gear wheel material
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks
Enclosure class IP 40
Weight [kg] 0,560
404 743
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
0.0 0.9 1.8 2.7 3.5 4.4 5.3 6.2 7.1 8.0 8.9
0
2
4
6
8
10
12
14
16
18
20
0
300
600
900
1200
1500
1800
2100
2400
2700
3000
n
I
I Terminal 1
II Terminal 5
98
Notes:
Series 0220 (GMP)Motor type 404 743
I Terminal housing 5-poleTYCO C-208-15621 (Z)
II Mating connector TYCO 1379217-3 + TYCO 1379218-2
99
Series 0220 (GMP)Motor type 404 744
Technical DataRated voltage UN [Volt] 12
No-load speed n0 [min-1] 2700
Nominal torque MN [Nm] 0,10
ON time %
ON [min]
Starting torque MA [Nm] 0,40
Gear ratio i
Armature resistance, 2 bars R [mΩ] 800,00
4 bars R [mΩ] 440,00
Armature inductance, 2 bars L [mH] 0,72
4 bars L [mH] 0,51
Armature load inertia JR [kgm2] × 10-6 18,00
Gear wheel material
Hall IC X
Pulses/rev. drive shaft 1
Output channels 1
Remarks
Enclosure class IP 40
Weight [kg] 0,560
404 744
M/Nm
in-lbs
I/An/min-1
0
5
10
15
20
25
30
35
40
45
50
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
0.0 0.9 1.8 2.7 3.5 4.4 5.3 6.2 7.1 8.0 8.9
0
2
4
6
8
10
12
14
16
18
20
0
300
600
900
1200
1500
1800
2100
2400
2700
3000
n
I
I Terminal 1
II Terminal 5
100
Notes:
Series 0220 (GMP)Motor type 404 744
I Terminal 4, Hall-IC +
II Terminal 2, Hall-IC -
I Terminal housing 5-poleTYCO C-208-15621 (Z)
II Mating connector TYCO 1379217-3 + TYCO 1379218-2
101
Series 0220 (GMP)Motor type 402 944
Technical DataRated voltage UN [Volt] 12
No-load speed n0 [min-1] 2700
Nominal torque MN [Nm] 0,08
ON time %
ON [min]
Starting torque MA [Nm] 0,28
Gear ratio i
Armature resistance, 2 bars R [mΩ] 1,00
4 bars R [mΩ] 0,85
Armature inductance, 2 bars L [mH] 0,63
4 bars L [mH] 0,50
Armature load inertia JR [kgm2] × 10-6 14,00
Gear wheel material
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks
Enclosure class IP 30
Weight [kg] 0,550
402 944
M/Nm
in-lbs
I/An/min-1
0
10
20
30
40
50
60
70
80
90
100
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
0.0 0.9 1.8 2.7 3.5 4.4 5.3 6.2 7.1 8.0 8.9
0.0
0.8
1.6
2.4
3.2
4.0
4.8
5.6
6.4
7.2
8.0
0
300
600
900
1200
1500
1800
2100
2400
2700
3000
n
I
102
Series 0220 (GMP)Motor type 403 187
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 2800
Nominal torque MN [Nm] 0,08
ON time %
ON [min]
Starting torque MA [Nm] 0,32
Gear ratio i
Armature resistance, 2 bars R [mΩ] 5,20
4 bars R [mΩ] 4,00
Armature inductance, 2 bars L [mH] 4,60
4 bars L [mH] 4,00
Armature load inertia JR [kgm2] × 10-6 14,00
Gear wheel material
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks
Enclosure class IP 30
Weight [kg] 0,550
403 187
M/Nm
in-lbs
I/An/min-1
0
10
20
30
40
50
60
70
80
90
100
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
0.0 0.9 1.8 2.7 3.5 4.4 5.3 6.2 7.1 8.0 8.9
0.0
0.4
0.8
1.2
1.6
2.0
2.4
2.8
3.2
3.6
4.0
0
300
600
900
1200
1500
1800
2100
2400
2700
3000
n
I
103
Series 0272 (GMK)Plain DC motors
Technical Description
Motor casing: Deep drawn, corrossion protectedExcitation field: PermanentmagnetMethod of bearing, A-side: Ball bearingMethod of bearing, B-side: Sleeve bearingGear: ---Gear housing: ---Gear wheel: ---Gear greasing: ---
Mechanic interface: Output shaftElectric interface: Leads with connector or tinned leads
Encoder: optionalThermal protection: optionalRFI supression: optional
Use
IndustryLinear drivesGeneral machineryMaterial-handling technologyLaboratory devicesVending machinesMedical technologyConstruction technologyAir conditioningAgricultural technologyTraffic and communications technologyLeisure devicesDIYFilm / optics
104
Series 0272 (GMK)Motor type 404 753
Technical DataRated voltage UN [Volt] 12
No-load speed n0 [min-1] 3000
Nominal torque MN [Nm] 0,35
ON time %
ON [min]
Starting torque MA [Nm] 1,25
Gear ratio i
Armature resistance, 2 bars R [mΩ] 240,00
4 bars R [mΩ] 195,00
Armature inductance, 2 bars L [mH] 0,43
4 bars L [mH] 0,39
Armature load inertia JR [kgm2] × 10-6 54,00
Gear wheel material
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks
Enclosure class IP 30
Weight [kg] 0,900
404 753
M/Nm
in-lbs
I/An/min-1
0
10
20
30
40
50
60
70
80
90
100
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
0 2 4 5 7 9 11 12 14 16 18
0
5
10
15
20
25
30
35
40
45
50
0
300
600
900
1200
1500
1800
2100
2400
2700
3000
n
I
I Blade receptacles 2,8 x 0,8 DIN 46 247
II red
III black
105
Series 0272 (GMK)Motor type 404 384
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 3800
Nominal torque MN [Nm] 0,12
ON time %
ON [min]
Starting torque MA [Nm] 1,50
Gear ratio i
Armature resistance, 2 bars R [mΩ] 670,00
4 bars R [mΩ] 560,00
Armature inductance, 2 bars L [mH] 1,30
4 bars L [mH] 1,20
Armature load inertia JR [kgm2] × 10-6 70,00
Gear wheel material
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks 4 start worm
Enclosure class IP 30
Weight [kg] 0,900
404 384
M/Nm
in-lbs
I/An/min-1
0
10
20
30
40
50
60
70
80
90
100
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
0 2 4 5 7 9 11 12 14 16 18
0
3
6
9
12
15
18
21
24
27
30
0
400
800
1200
1600
2000
2400
2800
3200
3600
4000
n
I
I Blade receptacles 2,8 x 0,8 DIN 46 247
II red
III black
106
Series 0272 (GMK)Motor type 404 284
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 3100
Nominal torque MN [Nm] 0,19
ON time %
ON [min]
Starting torque MA [Nm] 1,30
Gear ratio i
Armature resistance, 2 bars R [mΩ] 970,00
4 bars R [mΩ] 810,00
Armature inductance, 2 bars L [mH] 2,00
4 bars L [mH] 1,80
Armature load inertia JR [kgm2] × 10-6 72,00
Gear wheel material
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks 1 start worm
Enclosure class IP 30
Weight [kg] 0,900
404 284
M/Nm
in-lbs
I/An/min-1
0
10
20
30
40
50
60
70
80
90
100
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
0 2 4 5 7 9 11 12 14 16 18
0
2
4
6
8
10
12
14
16
18
20
0
400
800
1200
1600
2000
2400
2800
3200
3600
4000
n
I
I Blade terminal receptacles 2,8 x 0,8 DIN 46 247
II green
III red
107
Series 0272 (GMK)Motor type 404 382
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 5250
Nominal torque MN [Nm] 0,12
ON time %
ON [min]
Starting torque MA [Nm] 1,10
Gear ratio i
Armature resistance, 2 bars R [mΩ] 530,00
4 bars R [mΩ] 360,00
Armature inductance, 2 bars L [mH] 0,90
4 bars L [mH] 0,80
Armature load inertia JR [kgm2] × 10-6 60,00
Gear wheel material
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks
Enclosure class IP 30
Weight [kg] 0,900
404 382
M/Nm
in-lbs
I/An/min-1
0
10
20
30
40
50
60
70
80
90
100
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
0 2 4 5 7 9 11 12 14 16 18
0
3
6
9
12
15
18
21
24
27
30
0
600
1200
1800
2400
3000
3600
4200
4800
5400
6000
n
I
I Blade receptacles 2,8 x 0,8 DIN 46 247
II red
III black
108
Series 0272 (GMK)Motor type 404 880
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 2200
Nominal torque MN [Nm] 0,15
ON time %
ON [min]
Starting torque MA [Nm] 1,40
Gear ratio i
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks 3 start worm
Enclosure class IP 30
Weight [kg]
404 880
M/Nm
in-lbs
I/An/min-1
0
10
20
30
40
50
60
70
80
90
100
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
0 2 4 5 7 9 11 12 14 16 18
0
2
4
6
8
10
12
14
16
18
20
0
300
600
900
1200
1500
1800
2100
2400
2700
3000
n
I
I Blade receptacles 2,8 x 0,8 DIN 46 247
II green
III red
109
Series 0272 (GMK)Motor type 404 757
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 2200
Nominal torque MN [Nm] 0,30
ON time %
ON [min]
Starting torque MA [Nm] 1,30
Gear ratio i
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks 2 start worm
Enclosure class IP 30
Weight [kg] 0,890
404 757
M/Nm
in-lbs
I/An/min-1
0
10
20
30
40
50
60
70
80
90
100
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
0 2 4 5 7 9 11 12 14 16 18
0
2
4
6
8
10
12
14
16
18
20
0
300
600
900
1200
1500
1800
2100
2400
2700
3000
n
I
I Blade receptacles 2,8 x 0,8 DIN 46 247
II red
III black
110
Series 0273 (GML)Plain DC motors
Technical Description
Motor casing: Deep drawn, corrossion protectedExcitation field: PermanentmagnetMethod of bearing, A-side: Ball bearingMethod of bearing, B-side: Sleeve bearingGear: ---Gear housing: ---Gear wheel: ---Gear greasing: ---
Mechanic interface: Output shaftElectric interface: Leads with connector or tinned leads
Encoder: optionalThermal protection: optionalRFI supression: optional
Use
IndustryLinear drivesGeneral machineryMaterial-handling technologyLaboratory devicesVending machinesMedical technologyConstruction technologyAir conditioningAgricultural technologyTraffic and communications technologyLeisure devicesDIYFilm / optics
111
Series 0273 (GML)Motor type 404 966
Technical DataRated voltage UN [Volt] 12
No-load speed n0 [min-1] 3730
Nominal torque MN [Nm] 0,30
ON time %
ON [min]
Starting torque MA [Nm] 1,95
Gear ratio i
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks
Enclosure class IP 30
Weight [kg] 1,100
404 966
M/Nm
in-lbs
I/An/min-1
0
10
20
30
40
50
60
70
80
90
100
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
0 2 4 5 7 9 11 12 14 16 18
0
8
16
24
32
40
48
56
64
72
80
0
400
800
1200
1600
2000
2400
2800
3200
3600
4000
n
I
I Spur wheel with cogging, 7 teeth,lead angle 20°
II inductive hardened
III Centering hole DIN 332
I Blade receptacles 6,3 x 1,5G&H 35032.213.011
II Cable red, 1,5mm2
III Cable black, 1,5mm2
112
Series 0273 (GML)Motor type 404 596
Technical DataRated voltage UN [Volt] 12
No-load speed n0 [min-1] 3750
Nominal torque MN [Nm] 0,40
ON time %
ON [min]
Starting torque MA [Nm] 1,40
Gear ratio i
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks
Enclosure class IP 30
Weight [kg] 1,150
404 596
M/Nm
in-lbs
I/An/min-1
0
10
20
30
40
50
60
70
80
90
100
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
0 2 4 5 7 9 11 12 14 16 18
0
6
12
18
24
30
36
42
48
54
60
0
400
800
1200
1600
2000
2400
2800
3200
3600
4000
n
I
I Blade receptacles 2,8 x 0,8 DIN 46 247
II red
III black
113
Series 0273 (GML)Motor type 404 536
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 4000
Nominal torque MN [Nm] 0,20
ON time %
ON [min]
Starting torque MA [Nm] 2,00
Gear ratio i
Armature resistance, 2 bars R [mΩ] 390,00
4 bars R [mΩ] 260,00
Armature inductance, 2 bars L [mH] 0,90
4 bars L [mH] 0,90
Armature load inertia JR [kgm2] × 10-6 90,00
Gear wheel material
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks 2 start worm
Enclosure class IP 30
Weight [kg] 1,150
404 536
M/Nm
in-lbs
I/An/min-1
0
10
20
30
40
50
60
70
80
90
100
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
0 2 4 5 7 9 11 12 14 16 18
0
5
10
15
20
25
30
35
40
45
50
0
400
800
1200
1600
2000
2400
2800
3200
3600
4000
n
I
I Blade receptacles 2,8 x 0,8 DIN 46 247
II red
III black
114
Series 0273 (GML)Motor type 404 965
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 3800
Nominal torque MN [Nm] 0,30
ON time %
ON [min]
Starting torque MA [Nm] 2,50
Gear ratio i
Armature resistance, 2 bars R [mΩ]
4 bars R [mΩ]
Armature inductance, 2 bars L [mH]
4 bars L [mH]
Armature load inertia JR [kgm2] × 10-6
Gear wheel material
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks
Enclosure class IP 30
Weight [kg] 1,100
404 965
M/Nm
in-lbs
I/An/min-1
0
10
20
30
40
50
60
70
80
90
100
0.0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0
0 3 5 8 11 13 16 19 21 24 27
0
6
12
18
24
30
36
42
48
54
60
0
400
800
1200
1600
2000
2400
2800
3200
3600
4000
n
I
I Spur wheel with cogging, 7 teeth,lead angle 20°
II inductive hardened
III Centering hole DIN 332
I Blade receptacles 6,3 x 0,8G&H 35040.213.011
II Cable red, 0,88mm2
III Cable green, 0,88mm2
115
Series 0273 (GML)Motor type 404 889
Technical DataRated voltage UN [Volt] 24
No-load speed n0 [min-1] 2780
Nominal torque MN [Nm] 0,20
ON time %
ON [min]
Starting torque MA [Nm] 1,90
Gear ratio i
Armature resistance, 2 bars R [mΩ] 790,00
4 bars R [mΩ] 510,00
Armature inductance, 2 bars L [mH] 1,80
4 bars L [mH] 1,70
Armature load inertia JR [kgm2] × 10-6 85,00
Gear wheel material
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks 2 start worm
Enclosure class IP 30
Weight [kg] 1,150
404 889
M/Nm
in-lbs
I/An/min-1
0
10
20
30
40
50
60
70
80
90
100
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
0 2 4 5 7 9 11 12 14 16 18
0
3
6
9
12
15
18
21
24
27
30
0
300
600
900
1200
1500
1800
2100
2400
2700
3000
n
I
I Blade receptacles2,8 x 0,8 DIN 46 247
II green
III black
116
Series 0273 (GML)Motor type 404 469
Technical DataRated voltage UN [Volt] 36
No-load speed n0 [min-1] 4100
Nominal torque MN [Nm] 0,20
ON time %
ON [min]
Starting torque MA [Nm] 2,80
Gear ratio i
Armature resistance, 2 bars R [mΩ] 790,00
4 bars R [mΩ] 510,00
Armature inductance, 2 bars L [mH] 1,80
4 bars L [mH] 1,70
Armature load inertia JR [kgm2] × 10-6 85,00
Gear wheel material
Hall IC
Pulses/rev. drive shaftOutput channels
Remarks 2 start worm
Enclosure class IP 30
Weight [kg] 1,150
404 469
M/Nm
in-lbs
I/An/min-1
0
10
20
30
40
50
60
70
80
90
100
0.0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0
0 3 5 8 11 13 16 19 21 24 27
0
4
8
12
16
20
24
28
32
36
40
0
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
n
I
I Blade receptacles 2,8 x 0,8 DIN 46 247
II red
III black
Index
117
Order-No. Page Order-No. Page Order-No. Page402 525 82402 826 81402 853 86402 944 101
403 187 102403 334 83403 362 84403 460 87403 474 59403 475 60403 930 69403 931 71403 933 67403 936 73
404 157 9404 284 106404 360 79404 382 107404 384 105404 385 75404 386 77404 465 91404 469 116404 476 95404 536 113404 596 112404 603 12404 636 89404 682 30404 722 92404 743 97404 744 99404 747 22404 748 25404 753 104404 757 109404 763 10
404 764 31404 774 13404 846 17404 847 19404 853 43404 854 48404 864 42404 865 40404 866 46404 867 52404 868 55404 872 54404 880 108404 885 63404 889 115404 904 27404 905 28404 907 23404 909 38404 910 14404 925 66404 965 114404 966 111404 983 62404 987 56404 988 50404 990 33404 991 36
405 002 35405 006 44