brokelmann w50 - balkan
DESCRIPTION
Brokelmann W50 - BalkanTRANSCRIPT
SERIES W50W50TECHNICAL CATALOGUE
3
www.balkan.gr
W50
1 Catalogue cover
3 Catalogue pages – Overview
4 Design Description
5 System Description
6 Installation Depths/Levels/Drainage Facilities
7 Statics Table
8 Statics Table
9 Statics Table
10 Statics Table
11 Statics Table
12 Dimensioning of Mullions and Transoms
13 Predimensioning Table
14 Statics Predimensioning, Spar Spacing 80 cm
15 Statics Predimensioning, Spar Spacing 90 cm
16 Statics Predimensioning, Spar Spacing 100 cm
17 Statics Predimensioning, Spar Spacing 110 cm
18 Statics Predimensioning, Spar Spacing 120 cm
19 Calculation of the Thermal Conductivity Coefficient Ucw
20 Nominal Values of Thermal Conductivity Coefficient Uf
21 Profiles
22 Profiles
23 Profiles
24 Profiles
25 Profiles
26 Profiles
27 Profiles
28 Profiles
29 Profiles
30 Profiles
31 Profiles
32 Profiles
33 Profiles
34 Profiles
35 Profiles, pressure and cover profiles
36 Frame Inserts
37 Frame Inserts
38 Frame Inserts
39 Window Inserts
40 Auxiliary and connecting profiles
41 Variable angle profiles
42 Accessories
43 Accessories
44 Accessories
45 Accessories
46 Corner connectors
47 Corner connectors
48 Corner connectors
49 T-connection
50 T-connection
51 T-connection
52 T-connection
53 T-connection
54 T-connection
55 T-connection
56 T-connection
57 T-connection
58 T-connection
59 T-connection
60 T-connection
61 T-connection
62 T-connection
63 T-connection
64 T-connection
65 T-connection
66 T-connection
67 Reinforcement
68 Variable T-connection
69 Variable T-connection
70 Variable T-connection
71 Accessories72 Accessories73 Accessories74 Screws75 T-connection76 Cutting Points77 Drilling template78 Drilling template79 T-connection transom80 Cutting point, horizontal81 Installation of insulator PK 426 in sash area
82 Cut lengths83 Facade connections84 Cutting point85 Cutting point86 Cutting point87 Cutting point88 Cutting point89 Cutting point90 Cutting point91 Cutting point92 Cutting point93 Cutting point94 Cutting point95 Cutting point96 Section of A turning mode (45o angle)97 Section of A turning mode (60o angle)
98 Cutting point, horizontal, below or above the window sash
99 Cutting point100 Cutting point101 Cutting point102 Cutting point103 Cutting point104 Cutting point105 Cutting point106 Cutting point107 Cutting point108 Cutting point109 Cutting point110 Cutting point
Curtain Wall system for facades and roofs
Heat-insulated building construction Series W 50
4
April 2009
W50Curtain Wall system for facades and roofs
Thermal-insulated building construction Series W 50Design Description
Light alloy profile system for facades
* The installation depths indicated in the catalogue are reference dimensions for planning. The manufactured dimensions for frame and sash profiles lie 0.4 mm above the nominal dimensions in the catalogue, the glazing bar profiles 0.2 mm
Facade: Thermal-insulated facade mullion-and-transom construction with disengaged transom profiles for optimum load transmission. The heat insulation, formed from the insulator profile, is integrated into the supporting inner profile over its full length by means of a special groove.
Uf values to EN ISO 10077. Dimension values Uf,BW to DIN V 4108-4: 2002
The glazing or the installation of insert elements such as e.g. windows or doors is made with pressure profiles screwed on from the outside. With a corresponding mullion formation (half mullions), the facade can be fitted with the W50 concealed window sash. Cover profiles in various heights and forms are available for covering the pressure profiles.
Dimensions*: Mullion and transom profiles with 50 mm visible width. Installation depths available in graduated dimensions according to statics requirements from 80 mm to 200 mm.
Statics: The design conforms in its statics to DIN 4113, DIN 1005 and unconditionally to the technical guidelines of the glass industry.
5
www.balkan.gr
W50System Description
9. The pressure profiles are screwed on through the insulator into preformed screw channels of the mullion and transom profiles with a maximum spacing of 25 cm.
10. The pressure profiles are covered uding cover profiles in various heights and forms from 12 to 30 mm. The vertical cover profiles should stand higher than the horizontal cover profiles.
11. All profiles can be anodised or painted.
12. The heat insulation, formed from the insulator profile, is integrated into the supporting inner profile over its full length by means of a special groove. The Uf values were determined in accordance with DIN EN ISO 10077-2. Dimensioning values Uf, BW to DIN V 4108-4: 2002.
13. The outer cover profiles at the facade junction points have a visible width corresponding to the viewing angles.
14. The aluminium profiles extruded dimensionally to DIN EN 12020 are made of the alloy DIN 6060 (AIMgSi 0.5 F-22) in anodised quality.
15. The design conforms in its statics to DIN 4113, DIN 1005 and unconditionally to the technical guidelines of the glass industry.
16. All loads occurring must be reliably transmitted to the building.
17. The “Code of Practice for the Processor” in our latest main catalogue must be observed for the use and processing of our design.
1. The visible width of the facade profiles is 50 mm.
2. The installation depths of the mullion and transom profiles are designed in graduated dimensions according to statics requirements from 80 mm to 200 mm. Half mullions and half transoms to receive D, DK and tilting sashes while maintaining the…mm outside visible width in the window area by concealed, integrated ashes.
3. Room-side hollow chambers for installation of special push-in profiles for securing and connection of the mullion profiles.
4. Facade mullion-and-transom constructions with disengaged mullion profiles for transom connection and hence for optimum load transmission. Sash available with clamped and bpnded glazing.
5. The glazing or the installation of insert elements such as e.g. windows or doors is made with pressure profiles screwed on from the outside. Glazings and panels with thicknesses from 24 to 38 mm can be installed using spacers and/or gasket profiles. The use of integrated window profiles in conjunction with half mullion or half transom profiles is possible.
6. The dry glazing is performed from inside and outside with EPDM gaskets. Ventilation of the glazing rabbet from the outside is effected via special ventilation channels.
7. Draining is effected under control via drainage levels or the mullion or transom profiles.
8. All connecting and retaining parts of the facade construction are made from aluminium or stainless steel.
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Design Description
6
April 2009
W50
Mullion
Level 3
Transom
Level 1
Transom
Level 2
Installation Depths/Levels/Drainage
shown in reduced size
Mullion, Vertical
Level 3
Transom, Vertical
Level 1
Transom, Horizontal
Level 2
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Installation Depths/Levels/Drainage
Drawn rotated
through 90o
7
www.balkan.gr
W50Curtain Wall system for facades and roofs
Thermal-insulated building construction Series W 50Statics Table
Statics Table, Profile Series W50
Mullion Level 3, Vertical Profile No.: Ix cm4 min Wx cm3 ex cm2 Iy cm4 min
Wy cm3 ey cm2
AH550-5114080
W51 1408062.76 14,14 4,26 22,16 8,86 2,50
AH550-5114100
W51 14100107,53 19,39 5,15 26.35 10,54 2,50
AH550-5114120
W51 14120167,14 25,20 6,06 30,53 12,21 2,50
AH550-5114140
W51 14140243,04 31,53 6,99 34,71 13,88 2,50
AH550-5114160
W51 14160352,81 40,72 8,03 43,47 17,39 2,50
AH550-5114180
W51 14180553,02 58,90 9,31 56,17 22,47 2,50
AH550-5114200
W51 14200790,30 74,78 10,13 66,36 26,54 2,50
AH550-5115080
W51 1508039,89 8,17 3,81 5,25 2,41 1,30
AH550-5115120
W51 15120111,40 15,30 5,42 6,24 2,72 1,19
AH550-5115160
W51 15160249,00 26,50 7,30 7,35 3,08 1,09
AH550-5113080
W51 1308083,60 17,85 4,01 83,60 17,85 4,01
8
April 2009
W50Curtain Wall system for facades and roofs
Thermal-insulated building construction Series W 50Statics Table
Transom Level 1, Vertical Profile No.: Ix cm4 min Wx cm3 ex cm2 Iy cm4 min
Wy cm3 ey cm2
AH550-5121077
W51 2107755,84 13,01 4,11 20,64 8,25 2,50
Statics Table, Profile Series W50
Transom Level 2, Horizontal Art Nr.: Ix cm4 min Wx cm3 ex cm2 Iy cm4 min
Wy cm3 ey cm2
AH550-5122011
W51 220110,61 0,49 0,54 4,46 1,78 2,50
AH550-5122024
W51 220242,85 1,60 1,27 8,70 3,48 2,50
AH550-5122039
W51 220399,09 3,90 2,21 11,84 4,73 2,50
AH550-5122054
W51 2205420,07 6,43 2,92 14,84 5,99 2,50
AH550-5122079
W51 2207950,74 11,12 3,99 20,20 8,08 2,50
AH550-5122099
W51 22099101,07 18,97 5,22 25,22 10,09 2,50
AH550-5122119
W51 22119157,44 24,63 6,16 29.41 11.76 2.50
AH550-5122139
W51 22139229,37 30,82 7,10 33.59 13.43 2.50
AH550-5122159
W51 22159334,15 39,76 8,14 42.38 16.95 2.50
Mullion Adaptor for Variable Angles Profile No.: Ix cm4 min Wx cm3 ex cm2 Iy cm4 min
Wy cm3 ey cm2
AH550-5113001 2,8731 1,545 1,21 9,0602 3,62 2,15
9
www.balkan.gr
W50Curtain Wall system for facades and roofs
Thermal-insulated building construction Series W 50Statics Table
Transom, Frames, Sashes Profile No.: Ix cm4 min Wx cm3 ex cm2 Iy cm4 min
Wy cm3 ey cm2
AH550-5122080
W51 2208041,10 8,53 3,88 5,10 2,35 1,30
AH550-5150053
W51 5005313,72 4,65 2,45 5,37 2,14 1,69
AH550-5150080
W51 5008026,22 5,99 3,62 6,11 2,97 1,44
AH550-5150003 9,18 2,78 2,06 48,8 9 1,23
AH275-280 10,51 3,85 2,15 50,3 9,13 1,29
AH550-5150015
Statics Table, Profile Series W50
Push-in profiles for mullions Profile No.: Ix cm4 min Wx cm3 ex cm2 Iy cm4 min.
Wy cm3 ey cm2
AH550-5182080
W51 8208033.81 10.50 3.05 20.78 9.19 2.26
AH550-5182100
W51 8210068.81 16.09 3.99 26.13 11.56 2.26
AH550-5182120
W51 82120120.02 22.56 4.95 31.48 13.93 2.26
AH550-5182140
W51 82140189.88 29.88 5.91 36.83 16.30 2.26
AH550-5182160
W51 82160280.77 38.04 6.89 42.19 18.66 2.26
AH550-5182180 429.49 51.86 2.22 22.32 10.05 8.28
AH550-5182200 571.37 62.13 2.20 24.17 10.99 9.19
10
April 2009
W50Curtain Wall system for facades and roofs
Thermal-insulated building construction Series W 50Statics Table
Pressure plate and cover profiles Profile No.: Dev. anod. [mm]
Dev. elox. [mm]
AH550-5051006
W50 51006155 50
AH 550-50 57010
W50 57010182 -
AH550-5061012
W50 61012147 74
AH550-5061015
W50 61015159 80
AH550-5061020
W50 61020177 90
AH550-5067030
W50 67030248 155
AH550-5063098 293 206
AH550-5113002 256 58
AH550-5113003 218 49
AH550-5113004 354 81
AH550-5113005 104 29
AH550-5113006 83 11
Pressure plate and cover profiles Profile No.: Dev. anod. [mm]
Dev. elox. [mm]
AH550-9071008
W90 7100868 53
AH550-9071010
W90 7101076 45
Statics Table, Profile Series W50
11
www.balkan.gr
W50Curtain Wall system for facades and roofs
Thermal-insulated building construction Series W 50Statics Table
Connectors profiles for structural Profile No.: Dev. anod. [mm
Dev. elox. [mm]
AH550-901 119 -
AH550-902 114 -
AH550-903 97 -
Connectors profiles Profile No.: Dev. anod. [mm
Dev. elox. [mm]
AH550-5184045 215 -
AH550-5184044 214 -
AH550-5184046 217 -
AH550-5184346 216 -
AH550-5182000 974 -
AH550-5184001 192 -
AH550-5184002 98 -
Glass support Profile No.: Dev. anod. [mm
Dev. elox. [mm]
AH550-5156042
W51 5604294 -
AH550-5156053
W51 56053123 -
AH550-5150001 54 -
AH550-5150002 83 -
Statics Table, Profile Series W50
12
April 2009
W50Curtain Wall system for facades and roofs
Thermal-insulated building construction Series W 50Statics Table
Dimensioning of Mullions and Transoms
Loading width:The loading width c1 or c2 is determined by half the fields adjacent to the mullions or transoms.
Load case:A freely supported girder on two supports with trapezoidal or triangular load is assumed as the load case. The division of the load-bearing surface is effected by halving the angles.
Admissible bending:The general rule is fz ul. = q/300 • I (DIN 18056)The insulating glazing manufacturers regard this as the maximum bending between the support points of support spacing I, but limit the admissible bending in the partial area (bending between the supporting points of the largest part-area) to fzul. = 1/300 • I = 0,8 cm.
Load assumptions: (DIN 1055 Part 4)Dynamic pressure q = 0,5 kN/m2 (height above ground = 0-8 m)Dynamic pressure q = 0,8 kN/m2 (height above ground = 8-20 m)Dynamic pressure q = 1,1 kN/m2 (height above ground = 20-10m)Pressure coefficient cp = 0,8 + 1/4 = 1,0Wind pressure w = q • c p (kN/m2)Material strength specificationsof the Al alloy AlMgSi 0.5 F22 (DIN 4113)Minimum tensile strength β z = 22 kN/cm2
Minimum yield strength d 0,2 = 16 kN/cm2
Admissible strain (main load H): d zul = 95 N/mm2
Modulus of elasticity E = 7000 kN/cm2
Application of tables I and IIFor mullions or transoms of single-pane fields Example “A” use Table IFor mullions or transoms of multi-pane fields Example “Β” use Table II if all the part-areasare = 240 cm in size.In Example “C” the largest partial area of the mullion is dimensioned as 320 cm. As this is larger than 240 cm, f zul. = 0,8 cmor fzul. = lp/ 0,8 • I = 320/0,8 • I = 1/400 • I applies for this area.
This admissible bending of 1/400 • I of the partial area applies to the whole mullion lengthof 460cm.
In order to determine the necessary inertia moment Ix, the value from Table II oppositemust first be divided by 300 and thenmultiplied by 400.
Loading width
Sup
port
wid
th
1 (c
m)
Mullionspacing
Mullionspacing
Sup
port
wid
th
1 (c
m)
Mullionspacing
Mullionspacing
Sup
port
wid
th
1 (c
m) =
460
cm
Transom
Transom
Mullionspacing
Mullionspacing
Sup
port
wid
th
1 (c
m) =
460
cm
Mullionspacing
Mullionspacing
Transom
13
www.balkan.gr
W50Support width 1 (cm)
180
3,2
4,7
6,0
7,2
8,1
8,8
9,2
9,4
190
3,8
5,5
7,1
8,5
10,6
10,6
11,3
11,6
200
4,4
6,5
8,4
10,1
12,7
12,7
13,6
14,1
14,3
210
5,1
7,5
9,7
11,8
15,0
15,0
16,2
16,9
17,3
220
5,9
8,6
11,3
13,7
17,6
17,6
19,0
20,1
20,7
20,9
230
6,7
9,9
12,9
15,7
20,4
20,4
22,2
23,5
24,5
24,9
240
7,6
11,3
14,8
18,0
23,5
23,5
25,6
27,3
28,6
29,4
29,6
250
9,0
13,3
17,4
21,3
27,9
27,9
30,6
32,8
34,5
35,7
36,3
260
10,5
15,6
20,5
25,0
33,0
33,0
36,3
39,1
41,3
42,9
43,9
44,2
270
12,2
18,2
23,9
29,2
38,7
38,7
42,7
46,2
49,0
51,1
52,6
53,3
280
14,2
21,0
27,7
33,9
45,1
45,1
49,9
54,1
57,6
60,4
62,4
63,6
64,0
290
16,3
24,2
31,9
39,2
52,3
52,3
58,0
63,0
67,3
70,8
73,5
75,3
76,2
300
18,7
27,8
36,6
45,0
60,3
60,3
67,0
73,0
78,2
82,5
85,9
88,4
89,9
90,4
310
21,3
31,7
41,8
51,5
69,2
69,2
77,0
84,0
90,2
95,5
99,8
103
105
106
320
24,2
36,1
47,6
58,6
78,9
78,9
88,0
96,3
104
110
115
119
122
124
125
330
27,4
40,8
53,9
66,4
89,7
89,7
100
110
118
126
132
137
141
144
145
340
30,9
46,0
60,8
75,0
102
102
114
125
135
143
151
157
163
166
168
169
350
34,7
51,7
68,3
84,4
114
114
128
141
152
163
172
179
186
190
194
195
360
38,9
57,9
76,6
94,6
129
129
144
159
172
184
195
204
211
217
221
224
225
370
43,4
64,7
85,5
106
144
144
162
178
193
207
219
230
239
247
252
256
258
380
48,3
72,0
95,3
118
161
161
180
199
216
232
246
259
270
279
286
291
294
295
390
53,6
79,9
106
131
179
179
201
222
241
259
279
290
303
314
322
329
333
335
400
59,3
88,5
117
145
198
198
223
247
269
289
308
324
339
352
362
370
376
380
381
410
65,5
97,7
129
160
219
219
247
273
298
321
342
361
378
393
405
415
423
428
431
420
72,1
108
143
177
242
242
273
302
330
355
379
401
420
438
452
464
474
481
485
430
79,2
118
157
194
267
267
301
333
364
393
419
444
466
486
503
517
529
538
544
440
85,9
130
172
213
293
293
330
366
400
433
463
490
515
538
557
574
588
599
607
450
95,0
142
188
234
321
321
362
402
440
475
509
540
568
594
616
636
652
666
676
460
104
155
206
255
351
351
397
440
482
521
558
593
625
654
679
702
721
737
750
470
113
169
224
279
383
383
433
481
527
571
612
650
685
718
747
773
796
814
830
480
123
184
244
303
417
417
472
525
575
623
668
711
750
787
820
849
875
897
915
490
134
200
265
330
454
454
514
571
626
679
729
776
820
860
897
930
960
985
1007
500
145
217
288
358
493
493
558
620
681
739
793
845
894
939
980
1017
1051
1080
1105
510
157
235
312
387
534
534
605
673
739
802
862
919
972
1022
1068
1110
1148
1181
1210
520
170
254
337
419
578
578
655
729
800
869
935
997
1056
1111
1162
1209
1251
1288
1321
530
183
274
364
452
624
624
707
788
866
941
1012
1080
1145
1205
1262
1313
1361
1403
1440
540
197
295
392
488
674
674
763
851
935
1016
1094
1169
1239
1305
1367
1425
1477
1525
1567
550
212
318
422
525
726
726
822
917
1008
1097
1181
1262
1339
1411
1479
1543
1601
1654
1701
560
228
341
454
564
780
780
885
987
1086
1181
1273
1361
1445
1524
1598
1668
1732
1791
1844
570
245
357
487
606
838
838
951
1061
1168
1271
1370
1465
1556
1643
1724
1800
1871
1936
1995
580
263
393
522
650
900
900
1021
1139
1254
1365
1472
1576
1674
1768
1857
1940
2017
2089
2154
590
281
421
559
696
964
964
1094
1221
1345
1465
1580
1692
1799
1900
1997
2087
2172
2251
2323
600
301
450
598
745
1032
1032
1171
1308
1440
1569
1694
1814
1930
2040
2144
2243
2336
2422
2501
2030
4050
6070
8090
100
110
120
130
140
150
160
170
180
190
200
Loa
d w
idth
a [c
m]
9,4
9,2
8,8
8,1
7,2
64,
73,
218
0
Support width 1 (cm)
1211
119,
78,
57,
15,
53,
819
014
1414
1312
108,
46,
54,
420
017
1716
1514
129,
77,
55,
121
021
2120
1918
1514
118,
65,
922
025
2524
2220
1816
139,
96,
723
030
2929
2726
2421
1815
117,
624
035
3433
3229
2724
2017
138,
625
041
4140
3836
3431
2723
1914
9,7
260
4747
4544
4138
3430
2621
1611
270
5555
5452
4946
4339
3429
2418
1228
063
6261
5956
5248
4338
3226
2014
290
7272
7169
6663
5854
4842
3629
2215
300
8282
8077
7470
6560
5447
4032
2517
310
9493
9290
8683
7872
6659
5244
3627
1832
010
610
510
310
096
9286
8073
6557
4839
3020
330
119
119
117
115
111
107
101
9588
8072
6353
4333
2234
013
413
313
112
712
311
811
210
597
8879
6863
4736
2435
015
014
914
814
514
113
613
012
311
510
696
8675
6951
3926
360
167
166
164
160
155
149
142
134
125
115
105
9381
7456
4228
370
186
186
184
180
176
170
164
156
147
137
126
114
101
8881
6046
3138
020
620
520
219
819
318
617
917
016
014
913
712
411
096
8765
4933
390
229
228
226
222
217
211
203
195
185
173
161
148
134
119
103
9470
5336
400
252
251
248
243
237
230
221
211
200
188
174
160
145
128
111
101
7657
3841
027
727
527
126
525
825
024
022
921
720
318
817
315
613
812
010
982
6241
420
303
300
295
289
281
271
260
248
234
219
203
186
168
149
129
116
8866
4443
033
132
732
131
330
429
328
126
725
223
621
820
018
016
013
812
594
7147
440
360
355
348
339
329
317
303
288
271
254
235
214
193
171
148
133
100
7651
450
391
385
376
365
354
341
326
309
291
272
251
230
207
183
159
142
107
8154
460
424
416
406
395
382
367
350
332
312
291
269
246
221
196
169
152
115
8658
470
458
449
437
425
410
393
375
355
334
312
288
262
236
209
181
161
122
9262
480
493
483
470
456
439
421
402
380
357
333
307
280
252
222
192
172
130
9866
490
530
518
504
488
470
451
429
406
381
355
327
298
268
237
204
182
138
104
7050
056
955
654
052
250
348
145
843
240
637
734
831
728
525
121
719
314
711
074
510
610
595
577
558
536
513
487
460
432
401
369
336
302
267
230
205
155
117
7852
065
263
561
659
557
154
651
848
945
842
639
235
732
028
324
421
716
512
483
530
696
678
656
633
608
580
551
519
486
452
416
378
339
299
258
229
174
131
8854
074
272
269
967
364
661
658
455
151
547
844
040
035
931
727
324
218
413
993
550
790
767
742
715
685
653
619
583
546
506
465
423
379
334
289
255
194
146
9856
084
081
578
875
872
669
265
561
757
753
549
244
740
035
330
526
920
515
410
357
089
286
483
580
376
873
269
365
260
956
551
947
142
237
232
128
321
616
310
958
094
591
688
484
981
277
373
268
864
359
654
749
744
539
233
829
822
817
111
459
010
0196
993
489
785
881
677
272
667
862
857
652
346
941
335
623
923
918
012
060
0
200
190
180
170
160
150
140
130
120
110
100
9080
7060
5040
3020
Loa
d w
idth
a [c
m]
Con
vers
ion
fact
ors
Hei
ght
abov
egr
ound
Dyn
amic
pres
sure
q
Pre
ssu
reco
effic
ient
c p
Win
dpr
essu
re
w =
q •
cp
Fact
or
0-8m
8-20
m20
-100
m
0,5
kN/m
2
0,8
kN/ m
2
1,1
kN/m
2
1,0
1,0
1,0
0,5
kN/m
2
0,8
kN/m
2
1,1
kN/m
2
1,0
1,6
2,2
For
mu
llion
s or
tran
som
s of
mu
lti-p
ane
field
s, u
se T
able
II if
all
the
part
area
sar
e ≤
240
cm in
siz
e.Ta
ble
IIB
endi
ng f
= 1/
300
• I
Tabl
e fo
r de
term
inin
g th
e ne
cess
ary
iner
tia
mom
ents
Ix r
eq. [
cm4 ] f
or a
lum
iniu
m =
(E=
700
0 kN
/m2 )
Loa
d ca
se: F
reel
y su
ppor
ted
gird
er o
n tw
o su
ppor
ts w
ith tr
apez
oida
l or
tria
ngu
lar
load
.Th
e va
lues
indi
cate
d se
rve
only
for
prof
ile p
redi
men
sion
ing
and
are
no a
ltern
ativ
e to
an
exam
inab
le s
tatic
s ca
lcu
latio
n.
Tabl
e I
Ben
ding
f =
1/3
00 •
I ≤
0,8
cm
For
mu
llion
s or
tran
som
sS
ingl
e-pa
ned
field
s,u
se T
able
I
Det
erm
inat
ion
of th
e ne
cess
ary
iner
tia m
omen
tsTh
e de
term
inat
ion
is p
erfo
rmed
in th
e fo
llow
ing
orde
r:1.
Det
erm
inat
ion
of s
upp
ort w
idth
I in
cm
.2.
Det
erm
inat
ion
of lo
ad w
idth
c1
and
c2 in
cm
.3.
Det
erm
inat
ion
of in
ertia
mom
ent I
x er
f. fo
r lo
ad w
idth
c1
acco
rdin
g to
corr
espo
ndin
g Ta
ble
I or
II.4.
Det
erm
inat
ion
of in
ertia
mom
ent I
x er
f. fo
r lo
ad w
idth
c2
acco
rdin
g to
corr
espo
ndin
g Ta
ble
I or
II.5.
Add
ition
of t
he n
eces
sary
iner
tia m
omen
ts d
eter
min
ed u
nder
3 a
nd 4
.6.
Mu
ltipl
icat
ion
of th
e su
m o
f the
nec
essa
ry in
ertia
mom
ents
by
the
fact
orfo
r th
e w
ind
pres
sure
.
They
are
cal
cula
ted
for
a w
ind
pres
sure
of
0,5
kN/m
². In
the
case
of o
ther
win
d pr
essu
res,
the
iner
tia m
omen
tde
term
ined
mu
st b
e m
ulti
plie
dby
the
corr
espo
ndin
g fa
ctor
.
Support width I (cm)
I= S
upp
ort w
idth
in c
mC
1= L
oad
wid
th in
cm
C2
= L
oad
wid
th in
cm
ppp
T p 0 w ddd bb
Support width I (cm)
IS
t
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Predimensioning Table
14
April 2009
W50Curtain Wall system for facades and roofs
Thermal-insulated building construction Series W 50Statics Predimensioning, Spar Spacing 80 cm
Con
vers
ion
fact
or fo
r in
crea
sed
snow
load
s w
ith r
oof a
ngle
s u
p to
60o
(app
rox.
val
ues
)
For
typi
cal s
now
load
So=
1,00
kN
/m2 ,
the
valu
es in
the
tabl
e m
ust
be
mu
ltipl
ied
by 1
.2Fo
r ty
pica
l sno
w lo
ad S
o=1,
00 k
N/m
2 , th
e va
lues
in th
e ta
ble
mu
st b
e m
ulti
plie
d by
1.4
Tabl
e fo
r de
term
inat
ion
of th
e ne
cess
ary
iner
tia
mom
ents
Ix r
eq. [
cm4 ] fo
r sp
ars
or m
ullio
ns o
f a
sh
ed r
oof
or in
clin
ed f
acad
e of
alu
min
ium
pro
file
s (E
=70
00 k
N/m
2 )
Lo
ad c
ase
: F
ree
ly s
up
po
rte
d g
ird
er
on
tw
o s
up
po
rts,
tra
pe
zoid
al o
r tr
ian
gu
lar
load
Be
nd
ing
max
f=
1/3
00
* I
(val
ue
s in
tab
le a
pp
ly f
or
max
. e
dg
e l
en
gth
of
ind
ivid
ual
gla
zin
gs
= 2
40
cm
) T
ypic
al s
no
w l
oad
So
= 0
,75
kN
/m2
De
ad w
eig
ht
g
=0
.47
kN
/m2
V
ert
ical
in
div
idu
al l
ive
lo
ad F
=1k
N
Sp
ar s
pac
ing
= 8
0 cm
Dyn
amic
pre
ssu
re q
= 1
,1 k
N/m
2 (b
uild
ing
heig
ht 2
0-10
0m)
Dyn
amic
pre
ssu
re q
= 0
,8 k
N/m
2 (b
uild
ing
heig
ht 8
-20m
)D
ynam
ic p
ress
ure
q =
0,5
kN
/m2
(bu
ildin
g he
ight
0-8
m)
80 a
Roo
f ang
le
dis2
5o30
o35
o40
o45
o50
o55
o60
o70
o80
o90
o
Column spasing 1(cm)
140
2521
2019
1716
1412
8 6
515
029
2524
2220
1917
1410
87
160
3429
2726
2422
1917
1110
817
039
3332
3027
2522
1913
1210
180
4438
3634
3128
2522
1614
1219
050
4341
3835
3229
2519
1714
200
5749
4643
4036
3328
2219
1721
064
5552
4945
4137
3226
2319
220
7162
5854
5046
4137
3026
2323
079
6865
6156
5147
4334
3026
240
8876
7267
6258
5449
3934
3025
097
8680
7468
6661
5544
3933
260
106
9790
8477
7569
6350
4438
270
117
109
102
9487
8477
7056
4942
280
127
122
114
105
9794
8679
6355
4729
013
913
512
611
710
810
596
8870
6153
300
154
150
140
130
119
116
107
9777
6859
310
170
166
155
144
132
128
118
107
8675
6532
018
718
317
115
814
614
113
011
894
8371
330
206
201
188
174
160
155
143
130
104
9178
340
225
220
206
191
175
170
156
142
113
100
8635
024
624
022
520
819
118
617
115
512
410
994
360
268
262
245
227
208
202
186
169
135
119
102
370
292
285
266
247
226
220
202
184
147
129
111
380
316
309
288
267
245
238
219
199
159
140
120
390
342
334
312
289
266
258
237
216
172
152
130
400
369
360
337
312
287
278
256
233
186
164
141
410
398
388
363
337
309
300
276
251
200
176
152
420
428
418
391
362
332
323
297
270
215
190
163
430
460
449
419
389
357
347
319
290
231
204
175
440
493
481
450
417
383
372
342
311
248
218
188
450
528
515
481
446
410
398
366
333
266
234
201
460
564
550
514
477
438
425
391
356
284
250
215
470
602
587
549
509
467
454
417
380
303
267
229
480
642
626
585
542
498
483
445
405
323
284
244
490
683
666
623
577
530
514
473
431
343
302
260
500
726
708
662
614
563
547
503
458
365
321
276
510
771
752
702
651
598
581
534
486
388
341
293
520
817
797
745
691
634
616
566
515
411
362
311
530
865
844
789
732
672
652
600
546
435
383
329
540
916
893
835
774
711
690
635
578
461
406
348
550
968
944
882
818
751
729
671
611
487
429
368
560
1022
997
932
864
793
770
708
645
514
453
389
570
1078
1052
983
911
837
812
747
680
542
477
410
580
1136
1108
1036
960
882
856
787
717
571
503
432
590
1196
1167
1090
1011
928
901
829
755
602
530
455
600
1258
1227
1147
1064
977
948
872
794
633
557
479
80 b
Roo
f ang
le
dis2
5o30
o35
o40
o45
o50
o55
o60
o70
o80
o90
o
Column spasing 1(cm)
140
2521
2019
1716
1412
109
915
029
2524
2220
1917
1513
1211
160
3429
2726
2422
2019
1615
1317
039
3332
3027
2624
2319
1816
180
4438
3634
3131
2927
2321
1919
050
4341
3836
3734
3227
2523
200
5749
4643
4243
4138
3230
2721
064
5552
4949
5047
4437
3431
220
7162
5856
5758
5551
4340
3623
079
7067
6466
6763
5850
4641
240
8880
7673
7576
7167
5752
4725
097
9186
8385
8681
7664
5954
260
106
102
9794
9697
9185
7367
6027
011
711
510
910
510
710
910
396
8275
6828
013
012
912
211
812
012
211
510
791
8476
290
145
143
136
131
134
136
128
119
101
9384
300
160
159
151
145
148
151
142
132
113
103
9431
017
717
616
716
116
416
715
714
612
411
410
432
019
519
418
417
718
118
417
316
113
712
611
433
021
521
320
219
519
920
219
017
715
113
812
534
023
523
322
221
321
722
120
819
416
515
113
735
025
725
424
223
323
724
222
721
218
016
515
036
028
027
726
425
425
926
324
723
119
618
016
337
030
430
128
627
628
128
626
925
121
319
617
838
033
032
731
129
930
531
029
127
223
121
219
339
035
735
333
632
333
033
631
529
425
023
020
840
038
538
236
334
935
633
634
031
727
024
822
541
041
541
139
137
638
439
136
734
229
126
724
242
044
744
242
140
541
342
039
536
831
328
826
143
048
047
545
243
544
445
242
439
533
630
928
044
051
450
948
446
647
548
445
442
436
133
130
045
055
054
551
949
950
951
848
645
338
635
432
146
058
858
355
453
354
455
452
048
541
337
934
347
062
862
259
156
958
059
155
551
744
040
436
748
066
966
363
060
661
963
059
155
146
943
139
149
071
270
567
164
565
867
062
958
749
945
841
650
075
775
071
368
670
071
366
962
453
148
744
251
080
379
675
772
874
375
671
066
256
451
746
952
085
284
480
377
278
880
275
370
259
854
849
753
090
289
485
081
883
485
079
874
463
358
152
754
095
594
690
086
588
389
984
478
767
061
555
755
010
0999
995
191
593
395
089
283
170
865
058
956
010
6510
5510
0496
698
510
0394
287
874
768
662
257
011
2411
1310
5910
1910
3910
5899
392
678
872
365
658
011
8411
7311
1610
7410
9511
1510
4797
683
176
269
259
012
4712
3511
7511
3011
5311
7411
0210
2887
580
372
860
013
1212
9912
3611
8912
1312
3511
5910
8192
084
476
6
80 c
Roo
f ang
le
dis2
5o30
o35
o40
o45
o50
o55
o60
o70
o80
o90
o
Column spasing 1(cm)
140
2521
2019
1717
1615
1313
1215
029
2524
2221
2120
1917
1615
160
3429
2726
2526
2524
2120
1817
039
3332
3031
3230
2925
2422
180
4438
3635
3738
3634
3028
2619
050
4341
4244
4543
4136
3431
200
5749
4749
5153
5148
4240
3721
064
5655
5760
6259
5649
4643
220
7165
6366
6972
6864
5753
5023
079
7472
7679
8278
7465
6157
240
8884
8387
9094
8984
7470
6525
097
9694
9810
210
610
196
8479
7426
010
810
810
611
111
612
011
410
895
8983
270
121
121
119
124
130
135
128
121
107
100
9328
013
513
613
313
914
515
114
313
612
011
210
429
015
115
114
815
516
216
816
015
113
312
511
630
016
716
816
417
217
918
617
716
714
813
812
931
018
518
518
119
019
820
619
618
516
315
314
232
020
420
420
020
921
822
721
620
418
016
915
733
022
422
422
023
024
024
923
722
419
818
517
234
024
524
624
025
226
327
325
924
521
620
318
935
026
726
826
327
528
729
828
326
823
622
220
636
029
129
228
630
031
232
530
929
225
724
122
537
031
731
831
132
634
035
333
531
728
026
224
438
034
334
533
735
336
838
336
434
430
328
426
539
037
237
336
538
239
841
439
337
232
830
828
640
040
140
339
441
243
044
742
540
235
533
230
941
043
243
442
544
546
448
245
843
338
235
833
342
046
546
745
747
849
951
849
346
641
138
535
943
050
050
149
051
453
655
752
950
044
141
438
544
053
653
752
655
157
459
756
753
647
344
441
345
057
357
556
358
961
563
960
757
450
747
544
246
061
361
560
163
065
768
364
961
354
150
747
247
065
465
664
267
270
172
869
265
557
854
250
448
069
769
968
471
674
777
673
869
861
657
753
749
074
274
472
876
279
582
678
574
365
561
457
250
078
879
177
481
084
587
883
578
969
665
360
851
083
784
082
286
089
793
288
683
873
969
364
552
088
789
087
191
295
198
994
088
978
473
568
453
094
094
392
396
610
0810
4799
594
183
077
872
454
099
499
897
610
2210
6611
0810
5399
687
982
476
655
010
5110
5510
3210
8011
2711
7111
1310
5292
987
181
056
011
1011
1410
8911
4111
9012
3611
7511
1198
191
985
557
011
7111
7511
4912
0312
5513
0412
3911
7210
3497
090
258
012
3412
3812
1112
6813
2313
7413
0612
3510
9010
2295
159
012
9913
0312
7513
3513
9314
4713
7513
0111
4810
7610
0160
013
6613
7113
4114
0514
6515
2214
4713
6812
0711
3210
53
15
www.balkan.gr
W50Curtain Wall system for facades and roofs
Thermal-insulated building construction Series W 50Statics Predimensioning, Spar Spacing 90 cm
Con
vers
ion
fact
or fo
r in
crea
sed
snow
load
s w
ith r
oof a
ngle
s u
p to
60o
(app
rox.
val
ues
)
For
typi
cal s
now
load
So=
1,00
kN
/m2 ,
the
valu
es in
the
tabl
e m
ust
be
mu
ltipl
ied
by 1
.2Fo
r ty
pica
l sno
w lo
ad S
o=1,
00 k
N/m
2 , th
e va
lues
in th
e ta
ble
mu
st b
e m
ulti
plie
d by
1.4
Tabl
e fo
r de
term
inat
ion
of th
e ne
cess
ary
iner
tia
mom
ents
Ix r
eq. [
cm2 ] f
or
spar
s or
mul
lions
of
a s
hed
roo
f or
incl
ined
fac
ade
of a
lum
iniu
m p
rofi
les
(E=
7000
kN
/m2 )
Lo
ad c
ase
: F
ree
ly s
up
po
rte
d g
ird
er
on
tw
o s
up
po
rts,
tra
pe
zoid
al o
r tr
ian
gu
lar
load
Be
nd
ing
max
f=
1/3
00
* I
(val
ue
s in
tab
le a
pp
ly f
or
max
. e
dg
e l
en
gth
of
ind
ivid
ual
gla
zin
gs
= 2
40
cm
) T
ypic
al s
no
w l
oad
So
= 0
,75
kN
/m2
De
ad w
eig
ht
g
=0
.47
kN
/m2
V
ert
ical
in
div
idu
al l
ive
lo
ad F
=1k
N
Sp
ar s
pac
ing
= 9
0 cm
Dyn
amic
pre
ssu
re q
= 1
,1 k
N/m
2 (b
uild
ing
heig
ht 2
0-10
0m)
Dyn
amic
pre
ssu
re q
= 0
,8 k
N/m
2 (b
uild
ing
heig
ht 8
-20m
)D
ynam
ic p
ress
ure
q =
0,5
kN
/m2
(bu
ildin
g he
ight
0-8
m)
90 a
Roo
f ang
le
dis2
5o30
o35
o40
o45
o50
o55
o60
o70
o80
o90
o
Column spasing 1(cm)
140
2521
2019
1716
1412
8 7
515
029
2524
2220
1917
1410
87
160
3429
2726
2422
1917
1211
917
039
3332
3027
2522
1915
1311
180
4438
3634
3128
2522
1715
1319
050
4341
3835
3229
2621
1816
200
5749
4643
4037
3431
2422
1821
064
5552
4945
4339
3629
2522
220
7164
6056
5149
4641
3329
2523
079
7469
6459
5752
4838
3329
240
8884
7973
6765
6054
4338
3325
098
9589
8376
7468
6249
4337
260
110
108
101
9386
8377
7056
4942
270
124
121
113
105
9694
8678
6255
4728
013
913
612
711
710
810
596
8870
6253
290
155
151
141
131
120
117
107
9878
6959
300
172
168
157
145
133
129
119
108
8676
6531
019
018
517
316
114
814
313
212
096
8472
320
209
204
191
177
163
158
145
132
105
9380
330
230
225
210
195
179
173
160
145
116
102
8834
025
224
623
021
319
610
917
515
912
711
296
350
276
269
251
233
214
208
191
174
139
122
105
360
300
293
274
254
233
226
208
189
151
133
114
370
326
318
298
276
253
246
226
206
164
145
124
380
354
345
323
299
275
267
245
223
178
157
135
390
383
374
349
324
297
289
266
242
193
170
146
400
414
404
377
350
321
312
287
261
208
183
157
410
446
435
407
377
346
336
309
281
224
198
170
420
480
468
438
406
373
362
333
303
241
213
183
430
516
503
470
436
400
388
357
325
259
228
196
440
553
539
504
467
429
416
383
349
278
245
210
450
592
577
540
500
459
446
410
373
298
262
225
460
633
617
577
535
491
477
439
399
318
280
241
470
675
659
616
571
524
509
468
426
340
299
257
480
720
702
656
608
559
542
499
454
362
319
274
490
766
747
698
646
595
577
531
483
385
339
291
500
814
794
742
688
632
613
565
514
410
361
310
510
865
843
788
731
671
651
599
545
435
383
329
520
917
895
836
775
712
691
636
578
461
406
349
530
971
948
885
821
754
732
673
613
489
430
370
540
1028
1003
937
869
798
774
712
648
517
455
391
550
1086
1060
990
918
843
818
753
685
546
481
413
560
1147
1119
1046
970
890
864
795
724
577
508
436
570
1210
1181
1103
1023
939
912
839
763
609
536
460
580
1275
1244
1163
1078
990
961
884
805
642
565
485
590
1343
1310
1224
1135
1042
1012
931
847
675
595
511
600
1413
1378
1288
1194
1097
1064
979
891
711
626
538
90 b
Roo
f ang
le
dis2
5o30
o35
o40
o45
o50
o55
o60
o70
o80
o90
o
Column spasing 1(cm)
140
2521
2019
1716
1413
1110
915
029
2524
2220
1918
1614
1312
160
3429
2726
2423
2220
1716
1417
039
3332
3028
2827
2521
1918
180
4438
3634
3334
3230
2523
2119
050
4341
3940
4138
3530
2825
200
5750
4846
4748
4542
3633
3021
064
5956
5455
5652
4941
3835
220
7168
6462
6364
6056
4844
4023
079
7874
7173
7470
6555
5146
240
9089
8581
8385
7974
6358
5225
010
210
196
9294
9690
8472
6660
260
115
114
109
104
107
108
102
9581
7467
270
129
128
122
117
120
122
114
107
9183
7628
014
514
313
713
113
413
612
811
910
293
8529
016
116
015
214
614
915
214
313
311
310
494
300
179
177
169
162
166
169
158
148
126
115
105
310
198
196
187
180
183
187
175
163
139
128
116
320
218
216
206
198
202
206
193
180
153
141
128
330
240
238
226
218
222
226
212
198
168
154
140
340
263
260
248
238
243
248
232
217
184
169
154
350
287
285
271
260
266
270
254
237
201
185
168
360
313
310
295
284
290
295
277
258
220
202
183
370
340
337
321
309
315
320
301
280
239
219
199
380
369
366
348
335
341
348
326
304
259
238
216
390
400
396
376
362
369
376
353
329
280
257
233
400
431
427
407
391
399
406
381
356
303
278
252
410
465
461
438
422
430
438
411
383
326
299
272
420
500
469
472
454
463
471
442
412
351
322
292
430
538
532
507
487
497
506
475
443
377
346
314
440
576
571
543
522
533
543
509
475
404
371
337
450
617
611
581
559
571
581
545
508
433
397
360
460
660
653
621
598
610
621
583
543
463
425
385
470
704
697
663
638
651
663
622
580
494
453
411
480
750
743
707
680
694
706
663
618
526
483
438
490
799
791
753
724
739
752
706
658
560
514
466
500
849
841
800
770
785
799
750
700
596
547
496
510
901
893
849
817
834
849
797
743
632
580
526
520
956
947
901
867
884
900
845
788
671
615
528
530
1013
1003
954
918
936
953
895
834
710
652
591
540
1071
1061
1010
971
991
1009
947
883
752
690
626
550
1133
1122
1067
1027
1047
1066
1001
933
794
729
661
560
1196
1185
1127
1084
1106
1126
1057
986
839
770
698
570
1262
1250
1189
1144
1167
1188
1115
1040
885
812
737
580
1330
1317
1253
1205
1230
1252
1175
1096
933
856
776
590
1400
1387
1319
1269
1295
1318
1238
1154
982
901
818
600
1473
1459
1388
1335
1362
1387
1302
1214
1033
948
860
90 c
Roo
f ang
le
dis2
5o30
o35
o40
o45
o50
o55
o60
o70
o80
o90
o
Column spasing 1(cm)
140
2521
2019
1818
1817
1514
1315
029
2524
2222
2322
2118
1716
160
3429
2726
2829
2726
2321
2017
039
3332
3234
3533
3128
2624
180
4438
3739
4042
4038
3331
2919
050
4544
4648
5047
4540
3735
200
5753
5254
5759
5653
4744
4121
064
6260
6366
6965
6254
5147
220
7172
7073
7679
7571
6359
5523
082
8280
8488
9187
8272
6863
240
9494
9296
100
104
9994
8378
7225
010
610
710
410
911
411
811
310
694
8882
260
120
120
118
123
129
134
127
120
106
9993
270
135
135
132
139
145
150
143
135
119
112
104
280
151
151
148
155
162
168
160
151
133
125
116
290
168
169
165
173
180
187
178
168
149
139
130
300
187
187
183
192
200
208
198
187
165
155
144
310
206
207
203
212
221
230
219
207
182
171
159
320
227
228
223
234
244
253
241
228
201
188
175
330
250
251
245
257
268
279
265
250
221
207
193
340
274
275
269
282
294
305
290
274
242
227
211
350
299
300
294
308
321
333
317
300
264
248
231
360
326
327
320
335
350
363
345
327
288
270
251
370
354
356
348
364
380
395
375
355
313
294
273
380
384
386
377
395
412
428
407
385
340
318
296
390
416
418
409
428
446
464
441
417
368
345
321
400
449
451
441
462
482
501
476
450
397
372
346
410
484
486
476
498
519
540
513
485
428
401
373
420
521
523
512
536
559
581
552
522
461
432
402
430
560
562
550
576
600
624
593
561
495
464
432
440
600
602
589
617
644
669
636
601
530
497
463
450
643
645
631
661
689
716
681
644
568
532
495
460
687
689
674
706
737
765
727
688
607
569
530
470
733
736
720
754
786
817
776
734
648
607
565
480
781
784
767
803
838
871
827
783
691
647
602
490
832
835
817
855
892
927
881
833
735
689
641
500
884
887
868
909
948
985
936
886
781
732
682
510
939
942
922
965
1007
1046
994
940
830
778
724
520
996
999
978
1024
1068
1109
1054
997
880
825
768
530
1055
1058
1035
1084
1131
1175
1117
1056
932
874
813
540
1116
1120
1096
1147
1197
1243
1182
1118
986
924
860
550
1180
1184
1158
1213
1265
1314
1249
1181
1042
977
909
560
1246
1250
1223
1281
1336
1388
1319
1247
1101
1032
960
570
1314
1319
1290
1351
1409
1464
1391
1316
1161
1088
1013
580
1385
1390
1360
1424
1485
1543
1466
1387
1224
1147
1068
590
1458
1463
1432
1499
1564
1625
1544
1460
1289
1208
1124
600
1534
1540
1506
1577
1645
1709
1624
1536
1356
1271
1183
16
April 2009
W50Curtain Wall system for facades and roofs
Thermal-insulated building construction Series W 50Statics Predimensioning, Spar Spacing 100 cm
Con
vers
ion
fact
or fo
r in
crea
sed
snow
load
s w
ith r
oof a
ngle
s u
p to
60o
(app
rox.
val
ues
)
For
typi
cal s
now
load
So=
1,00
kN
/m2 ,
the
valu
es in
the
tabl
e m
ust
be
mu
ltipl
ied
by 1
.2Fo
r ty
pica
l sno
w lo
ad S
o=1,
00 k
N/m
2 , th
e va
lues
in th
e ta
ble
mu
st b
e m
ulti
plie
d by
1.4
Tabl
e fo
r de
term
inat
ion
of th
e ne
cess
ary
iner
tia
mom
ents
Ix r
eq. [
cm2 ] f
or
spar
s or
mul
lions
of
a s
hed
roo
f or
incl
ined
fac
ade
of a
lum
iniu
m p
rofi
les
(E=
7000
kN
/m2 )
Lo
ad c
ase
: F
ree
ly s
up
po
rte
d g
ird
er
on
tw
o s
up
po
rts,
tra
pe
zoid
al o
r tr
ian
gu
lar
load
Be
nd
ing
max
f=
1/3
00
* I
(val
ue
s in
tab
le a
pp
ly f
or
max
. e
dg
e l
en
gth
of
ind
ivid
ual
gla
zin
gs
= 2
40
cm
) T
ypic
al s
no
w l
oad
So
= 0
,75
kN
/m2
De
ad w
eig
ht
g
=0
.47
kN
/m2
V
ert
ical
in
div
idu
al l
ive
lo
ad F
=1k
N
Sp
ar s
pac
ing
= 1
00 c
m
Dyn
amic
pre
ssu
re q
= 1
,1 k
N/m
2 (b
uild
ing
heig
ht 2
0-10
0m)
Dyn
amic
pre
ssu
re q
= 0
,8 k
N/m
2 (b
uild
ing
heig
ht 8
-20m
)D
ynam
ic p
ress
ure
q =
0,5
kN
/m2
(bu
ildin
g he
ight
0-8
m)
100
aR
oof a
ngle
dis2
5o30
o35
o40
o45
o50
o55
o60
o70
o80
o90
o
Column spasing 1(cm)
140
2521
2019
1716
1412
8 7
615
029
2524
2220
1917
1410
98
160
3429
2726
2422
1917
1311
1017
039
3332
3027
2522
2016
1412
180
4438
3634
3128
2624
1917
1419
050
4441
3835
3431
2823
2017
200
5752
4845
4140
3733
2723
2021
064
6056
5248
4743
3931
2724
220
7270
6561
5654
5045
3632
2723
083
8175
7064
6257
5242
3731
240
9492
8680
7371
6560
4842
3625
010
710
598
9183
8174
6854
4841
260
121
118
111
103
9491
8477
6154
4627
013
713
312
411
510
610
395
8669
6052
280
153
149
139
129
119
115
106
9677
6858
290
170
166
155
144
132
128
118
108
8675
6530
018
918
517
316
014
714
313
111
995
8472
310
209
204
191
177
163
158
145
132
105
9380
320
231
225
211
195
179
174
160
146
116
102
8833
025
424
823
221
519
719
117
616
012
811
297
340
278
272
254
235
216
210
193
176
140
123
106
350
304
297
277
257
236
229
211
192
153
135
116
360
332
324
302
280
257
250
230
209
167
147
126
370
361
352
329
305
280
272
250
228
181
160
137
380
391
382
357
331
304
295
271
247
197
173
149
390
424
413
386
358
329
319
294
267
213
188
161
400
458
446
417
387
355
345
317
289
230
203
174
410
493
481
450
417
383
372
342
311
248
219
188
420
531
518
484
449
412
400
368
335
267
235
202
430
570
557
520
482
443
430
395
360
287
253
217
440
612
597
558
517
475
461
424
386
308
271
233
450
655
639
597
554
508
494
454
413
330
290
249
460
700
683
638
592
544
528
486
442
352
310
266
470
748
729
682
632
580
563
518
472
376
331
284
480
797
778
727
674
619
600
552
503
401
353
303
490
848
828
773
717
659
639
588
535
427
376
323
500
902
880
822
763
700
680
625
569
454
400
343
510
958
934
873
810
743
722
664
604
482
424
364
520
1016
991
926
859
789
765
704
641
511
450
387
530
1076
1050
981
910
835
811
746
679
541
477
409
540
1139
1111
1038
963
884
858
790
718
573
504
433
550
1204
1175
1098
1018
935
907
835
760
606
533
458
560
1271
1240
1159
1075
987
958
881
802
640
563
484
570
1341
1309
1223
1134
1041
1011
930
846
675
594
510
580
1414
1379
1289
1195
1097
1065
980
892
711
626
538
590
1489
1452
1357
1259
1156
1122
1032
939
749
659
566
600
1566
1582
1428
1324
1216
1180
1086
988
788
694
596
100
cR
oof a
ngle
dis2
5o30
o35
o40
o45
o50
o55
o60
o70
o80
o90
o
901Column spasing 1(cm)
140
2521
2019
1920
1918
1615
1415
029
2524
2324
2524
2220
1817
160
3429
2728
3031
2928
2423
2117
039
3333
3536
3836
3430
2826
180
4438
4042
4446
4341
3634
3219
050
4448
5052
5452
4943
4038
200
5752
5659
6264
6158
5148
4421
067
6766
6972
7571
6459
5652
220
7878
7780
8487
8378
6965
6023
090
9088
9296
100
9590
7974
6924
010
310
310
110
511
011
410
910
391
8579
250
117
117
114
120
125
130
123
117
103
9790
260
132
132
129
135
141
147
140
132
116
109
102
270
148
149
146
152
159
165
157
148
131
123
114
280
166
167
163
171
178
185
176
166
147
138
128
290
185
186
182
190
198
206
196
185
164
153
143
300
206
206
202
211
220
229
218
206
182
170
158
310
227
228
223
234
244
253
241
228
201
188
175
320
251
252
246
258
269
279
266
251
222
208
193
330
276
277
271
283
296
307
292
276
244
228
213
340
302
303
297
311
324
337
320
303
267
250
233
350
330
332
324
340
354
368
350
331
292
274
255
360
260
361
354
370
386
401
381
361
318
298
278
370
392
393
385
403
420
436
415
392
346
324
302
380
425
426
417
437
456
473
450
426
376
352
328
390
460
462
452
473
493
513
487
461
407
381
355
400
497
499
488
511
533
554
526
498
439
412
383
410
536
538
526
551
575
597
567
537
474
444
413
420
577
579
566
593
618
643
611
577
510
478
445
430
620
622
608
637
664
690
656
620
547
513
487
440
664
667
652
683
712
740
704
665
587
550
512
450
711
714
698
731
763
793
753
712
629
589
548
460
761
763
747
782
815
847
805
762
672
630
586
470
812
815
797
835
870
905
860
813
717
672
626
480
865
868
850
890
928
964
916
867
765
717
667
490
921
925
905
947
988
1027
976
923
814
763
710
500
980
983
962
1007
1050
1091
1037
981
866
811
755
510
1040
1044
1021
1069
1115
1159
1101
1042
919
862
802
520
1103
1107
1083
1134
1183
1229
1168
1105
975
914
850
530
1169
1173
1147
1201
1253
1302
1238
1170
1033
968
901
540
1237
1241
1214
1271
1326
1378
1310
1239
1093
1024
953
550
1307
1312
1284
1344
1402
1457
1384
1309
1155
1083
1008
560
1381
1386
1356
1419
1480
1538
1462
1383
1220
1144
1064
570
1457
1462
1430
1497
1562
1623
1542
1459
1287
1207
1123
580
1535
1541
1507
1578
1646
1711
1626
1537
1357
1272
1183
590
1617
1622
1587
1662
1733
1801
1712
1619
1429
1339
1246
600
1701
1707
1670
1749
1824
1895
1801
1703
1503
1409
1311
100
bR
oof a
ngle
dis2
5o30
o35
o40
o45
o50
o55
o60
o70
o80
o90
o
Column spasing 1(cm)
140
2521
2019
1716
1514
1211
1015
029
2524
2220
2019
1815
1413
160
3429
2726
2525
2422
1917
1617
039
3332
3030
3129
2723
2119
180
4438
3634
3637
3532
2825
2319
050
4444
3843
4441
3933
3027
200
5755
5245
5152
4945
3936
3221
067
6461
5860
6157
5345
4238
220
7574
7168
6970
6662
5248
4423
086
8581
7880
8176
7160
5550
240
9898
9389
9193
8781
6963
5825
011
211
110
510
110
410
599
9279
7265
260
127
125
119
115
117
119
112
104
8981
7427
014
214
113
412
913
213
412
611
710
092
8328
015
915
815
014
414
715
014
113
111
210
393
290
178
176
167
161
164
167
157
146
125
114
104
300
197
185
189
179
183
186
174
163
138
127
115
310
218
216
206
198
202
206
193
180
153
141
128
320
241
239
227
218
223
227
213
198
169
155
141
330
265
262
249
240
245
249
234
218
186
170
155
340
290
287
273
263
268
273
256
239
204
187
169
350
317
314
299
288
293
299
280
261
222
204
185
360
346
342
326
313
320
326
306
285
243
223
202
370
376
372
354
341
348
354
332
310
264
242
220
380
408
404
384
370
377
384
361
336
286
263
238
390
442
437
416
400
408
416
390
364
310
284
258
400
477
473
450
433
441
449
422
393
335
307
279
410
514
510
485
466
476
484
455
424
361
331
300
420
554
548
522
502
512
521
489
456
388
356
323
430
595
589
560
539
550
560
526
490
417
383
347
440
638
632
601
578
590
601
564
526
447
411
372
450
683
676
644
619
632
643
604
563
479
440
399
460
730
723
688
662
675
688
645
602
512
470
426
470
779
772
734
707
721
734
689
642
547
502
455
480
831
823
783
753
768
782
734
685
583
535
485
490
885
876
834
802
818
833
782
729
620
569
517
500
940
931
886
853
870
885
831
775
660
605
549
510
999
989
941
905
924
940
883
823
700
643
583
520
1059
1049
998
960
979
997
936
873
743
682
618
530
1122
1111
1057
1017
1038
1057
992
925
787
722
655
540
1187
1176
1119
1076
1098
1118
1050
978
833
764
693
550
1255
1243
1183
1138
1161
1182
1110
1034
880
808
733
560
1326
1313
1249
1202
1226
1248
1172
1092
930
853
774
570
1398
1385
1318
1268
1293
1317
1236
1152
981
900
817
580
1474
1460
1389
1336
1363
1388
1303
1215
1034
949
861
590
1552
1537
1463
1407
1435
1462
1372
1279
1089
999
906
600
1633
1618
1539
1480
1510
1538
1444
1346
1146
1051
954
17
www.balkan.gr
W50Curtain Wall system for facades and roofs
Thermal-insulated building construction Series W 50Statics Predimensioning, Spar Spacing 110 cm
Con
vers
ion
fact
or fo
r in
crea
sed
snow
load
s w
ith r
oof a
ngle
s u
p to
60o
(app
rox.
val
ues
)
For
typi
cal s
now
load
So=
1,00
kN
/m2 ,
the
valu
es in
the
tabl
e m
ust
be
mu
ltipl
ied
by 1
.2Fo
r ty
pica
l sno
w lo
ad S
o=1,
00 k
N/m
2 , th
e va
lues
in th
e ta
ble
mu
st b
e m
ulti
plie
d by
1.4
Tabl
e fo
r de
term
inat
ion
of th
e ne
cess
ary
iner
tia
mom
ents
Ix r
eq. [
cm2 ] f
or
spar
s or
mul
lions
of
a s
hed
roo
f or
incl
ined
fac
ade
of a
lum
iniu
m p
rofi
les
(E=
7000
kN
/m2 )
Lo
ad c
ase
: F
ree
ly s
up
po
rte
d g
ird
er
on
tw
o s
up
po
rts,
tra
pe
zoid
al o
r tr
ian
gu
lar
load
Be
nd
ing
max
f=
1/3
00
* I
(val
ue
s in
tab
le a
pp
ly f
or
max
. e
dg
e l
en
gth
of
ind
ivid
ual
gla
zin
gs
= 2
40
cm
) T
ypic
al s
no
w l
oad
So
= 0
,75
kN
/m2
De
ad w
eig
ht
g
=0
.47
kN
/m2
V
ert
ical
in
div
idu
al l
ive
lo
ad F
=1k
N
Sp
ar s
pac
ing
= 1
10 c
m
Dyn
amic
pre
ssu
re q
= 1
,1 k
N/m
2 (b
uild
ing
heig
ht 2
0-10
0m)
Dyn
amic
pre
ssu
re q
= 0
,8 k
N/m
2 (b
uild
ing
heig
ht 8
-20m
)D
ynam
ic p
ress
ure
q =
0,5
kN
/m2
(bu
ildin
g he
ight
0-8
m)
110
aR
oof a
ngle
dis2
5o30
o35
o40
o45
o50
o55
o60
o70
o80
o90
o
Column spasing 1(cm)
140
2521
2019
1716
1412
9 8
615
029
2524
2220
1917
1411
108
160
3429
2726
2422
1917
1412
1017
039
3332
3027
2523
2117
1513
180
4438
3734
3130
2825
2018
1519
050
4444
4137
3633
3024
2118
200
5756
5248
4443
3936
2925
2221
067
6561
5652
5046
4234
3025
220
7876
7166
6058
5449
3934
2923
089
8781
7669
6762
5645
4034
240
102
100
9387
7977
7165
5145
3925
011
611
410
698
9088
8173
5952
4426
013
212
912
011
110
299
9183
6658
5027
014
814
513
512
511
511
210
394
7566
5628
016
616
215
214
112
912
511
510
584
7463
290
186
181
169
157
144
140
129
117
9382
7130
020
620
118
817
416
015
514
313
010
491
7831
022
822
320
819
317
717
215
814
411
510
187
320
252
246
230
213
196
190
175
159
127
112
9633
027
727
025
323
421
520
919
217
513
912
310
534
030
429
627
725
723
622
921
119
215
313
511
635
033
232
430
328
125
825
023
021
016
714
712
636
036
235
433
030
628
127
325
122
918
216
113
837
039
438
535
933
330
629
727
324
919
817
515
038
042
841
739
036
233
232
229
727
021
519
016
339
046
345
242
239
236
034
932
129
223
320
517
640
050
148
945
742
338
937
734
731
625
222
219
141
054
052
749
245
741
940
737
434
127
223
920
542
058
156
753
049
145
143
840
336
729
225
722
143
062
560
956
952
848
547
143
339
431
427
723
844
067
065
461
156
752
050
546
542
333
729
725
545
071
870
065
460
755
754
149
745
336
131
827
346
076
774
970
064
959
657
853
248
438
634
029
247
081
979
974
769
363
661
756
851
741
236
331
248
087
385
279
673
867
865
860
655
143
938
733
249
093
090
784
878
672
270
164
558
746
841
235
450
098
996
590
283
676
874
568
662
449
743
837
651
010
5010
2595
788
881
579
172
866
352
846
540
052
011
1410
8710
1694
286
583
977
270
356
049
342
453
011
8011
5110
7699
891
688
981
874
559
452
344
954
012
4912
1911
3910
5697
094
186
678
862
855
347
555
013
2112
8812
0411
1710
2599
591
683
366
458
550
356
013
9513
6112
7211
7910
8310
5196
788
070
261
853
157
014
7214
3613
4212
4411
4211
0910
2092
874
065
256
058
015
5115
1314
1413
1212
0411
6910
7597
978
068
759
059
016
3415
9414
8913
8112
6812
3111
3310
3182
272
462
260
017
1916
7715
6714
5313
3412
9511
9210
8486
576
165
4
110
cR
oof a
ngle
dis2
5o30
o35
o40
o45
o50
o55
o60
o70
o80
o90
o
901Column spasing 1(cm)
140
2521
2019
2021
2018
1615
1415
029
2524
2425
2625
2421
2018
160
3430
2930
3233
3129
2624
2317
039
3635
3739
4038
3632
3028
180
4444
4345
4749
4644
3936
3419
052
5251
5456
5855
5246
4340
200
6262
6164
6669
6562
5551
4821
072
7371
7478
8177
7364
6056
220
8484
8387
9094
8984
7470
6523
097
9795
100
104
108
103
9786
8075
240
111
112
109
114
119
124
118
111
9892
8625
012
612
712
413
013
614
113
412
711
210
597
260
143
144
141
147
153
159
152
143
126
119
110
270
161
162
158
166
173
180
171
161
142
133
124
280
181
181
177
186
194
201
191
181
160
150
139
290
202
202
198
207
216
225
213
202
178
167
155
300
224
225
220
230
240
250
237
224
198
186
173
310
248
249
243
255
266
276
263
248
219
205
191
320
274
275
269
281
293
305
290
274
242
227
211
330
301
302
295
309
323
335
319
301
266
249
232
340
330
331
324
339
354
368
349
330
292
273
254
350
361
362
354
371
387
402
382
361
319
299
278
360
394
395
386
405
422
439
417
394
348
326
303
370
428
430
420
440
459
477
453
429
378
355
330
380
465
466
456
478
498
518
492
465
411
385
358
390
503
505
494
517
540
561
533
504
445
417
388
400
544
546
534
559
583
606
576
545
481
450
419
410
586
589
576
603
629
653
621
587
518
486
452
420
631
634
620
649
677
703
668
632
558
523
487
430
678
681
666
697
727
756
718
679
599
562
523
440
728
730
714
748
780
811
770
729
643
603
561
450
779
782
765
801
835
868
825
780
689
645
601
460
833
836
818
857
893
928
882
834
736
690
642
470
890
893
873
915
954
991
942
891
786
737
686
480
948
952
931
975
1017
1057
1004
950
838
786
731
490
1010
1013
991
1038
1083
1125
1069
1011
892
836
778
500
1074
1078
1054
1104
1151
1197
1137
1075
949
889
828
510
1140
1144
1120
1172
1223
1271
1208
1142
1008
945
879
520
1210
1214
1188
1244
1297
1348
1281
1211
1069
1002
932
530
1282
1286
1258
1318
1374
1438
1357
1284
1133
1062
988
540
1357
1361
1332
1395
1454
1511
1436
1358
1199
1124
1046
550
1434
1439
1408
1474
1538
1598
1519
1436
1267
1188
1106
560
1515
1520
1487
1557
1624
1688
1604
1517
1338
1255
1168
570
1598
1604
1569
1643
1713
1781
1692
1600
1412
1324
1232
580
1685
1690
1654
1732
1806
1877
1784
1687
1489
1395
1299
590
1774
1780
1742
1824
1902
1977
1879
1777
1568
1469
1368
600
1867
1873
1833
1919
2001
2080
1977
1869
1650
1546
1439
110
bR
oof a
ngle
dis2
5o30
o35
o40
o45
o50
o55
o60
o70
o80
o90
o
Column spasing 1(cm)
140
2521
2019
1717
1615
1211
1015
029
2524
2221
2120
1916
1513
160
3429
2726
2627
2523
2018
1617
039
3433
3132
3331
2924
2220
180
4442
4038
3940
3735
2927
2519
050
5047
4646
4744
4135
3229
200
5959
5654
5556
5249
4238
3521
070
6966
6364
6661
5749
4541
220
8180
7673
7576
7167
5752
4723
093
9288
8486
8882
7765
6054
240
107
106
101
9799
100
9488
7569
6225
012
112
011
411
011
211
410
710
085
7871
260
137
136
129
125
127
129
121
113
9688
8027
015
515
314
614
014
314
613
712
810
910
090
280
173
172
163
157
160
163
153
143
122
112
101
290
193
192
182
175
179
182
171
159
136
125
113
300
215
213
203
195
199
202
190
177
151
138
126
310
238
236
224
216
220
224
210
196
167
153
139
320
263
260
248
238
243
247
232
216
184
169
153
330
289
286
272
262
267
272
255
238
203
186
169
340
317
314
299
287
293
298
280
261
222
204
185
350
346
343
326
314
320
326
306
286
243
223
202
360
378
374
356
343
349
356
334
311
265
243
221
370
411
407
387
373
380
387
363
339
288
265
240
380
446
442
420
404
413
420
394
368
313
287
261
390
483
479
455
438
447
455
427
398
339
311
282
400
522
517
492
473
483
492
461
430
366
336
305
410
563
558
531
510
521
530
498
464
395
362
329
420
606
600
571
549
561
571
536
499
425
390
354
430
651
645
614
590
602
613
576
537
457
419
380
440
699
692
658
633
646
658
617
576
490
450
408
450
748
741
705
678
692
704
661
617
525
482
437
460
800
792
754
725
740
753
707
659
561
515
467
470
854
846
805
774
790
804
755
704
599
550
499
480
911
902
858
826
842
857
805
750
639
586
532
490
970
960
914
879
897
913
857
799
680
624
566
500
1031
1021
971
935
953
971
911
850
723
664
602
510
1095
1084
1032
993
1013
1031
968
902
768
705
639
520
1161
1150
1094
1053
1074
1094
1027
957
815
748
678
530
1231
1219
1160
1116
1138
1159
1088
1014
863
792
719
540
1302
1290
1227
1181
1204
1226
1151
1073
914
838
760
550
1377
1364
1297
1248
1273
1296
1217
1135
966
886
804
560
1454
1440
1370
1318
1345
1369
1285
1198
1020
936
849
570
1534
1520
1446
1391
1419
1445
1356
1264
1076
988
896
580
1617
1602
1524
1466
1496
1523
1430
1333
1134
1041
944
590
1703
1687
1605
1544
1575
1604
1506
1404
1195
1097
995
600
1792
1775
1689
1625
1657
1687
1584
1477
1257
1154
1047
18
April 2009
W50C
onve
rsio
n fa
ctor
for
incr
ease
d sn
ow lo
ads
with
roo
f ang
les
up
to 6
0o (a
ppro
x. v
alu
es)
For
typi
cal s
now
load
So=
1,00
kN
/m2 ,
the
valu
es in
the
tabl
e m
ust
be
mu
ltipl
ied
by 1
.2Fo
r ty
pica
l sno
w lo
ad S
o=1,
00 k
N/m
2 , th
e va
lues
in th
e ta
ble
mu
st b
e m
ulti
plie
d by
1.4
Tabl
e fo
r de
term
inat
ion
of th
e ne
cess
ary
iner
tia
mom
ents
Ix r
eq. [
cm2 ] f
or
spar
s or
mul
lions
of
a s
hed
roo
f or
incl
ined
fac
ade
of a
lum
iniu
m p
rofi
les
(E=
7000
kN
/m2 )
Lo
ad c
ase
: F
ree
ly s
up
po
rte
d g
ird
er
on
tw
o s
up
po
rts,
tra
pe
zoid
al o
r tr
ian
gu
lar
load
Be
nd
ing
max
f=
1/3
00
* I
(val
ue
s in
tab
le a
pp
ly f
or
max
. e
dg
e l
en
gth
of
ind
ivid
ual
gla
zin
gs
= 2
40
cm
) T
ypic
al s
no
w l
oad
So
= 0
,75
kN
/m2
De
ad w
eig
ht
g
=0
.47
kN
/m2
V
ert
ical
in
div
idu
al l
ive
lo
ad F
=1k
N
Sp
ar s
pac
ing
= 1
20 c
m
Dyn
amic
pre
ssu
re q
= 1
,1 k
N/m
2 (b
uild
ing
heig
ht 2
0-10
0m)
Dyn
amic
pre
ssu
re q
= 0
,5 k
N/m
2 (b
uild
ing
heig
ht 0
-8m
)
120
aR
oof a
ngle
dis2
5o30
o35
o40
o45
o50
o55
o60
o70
o80
o90
o
Column spasing 1(cm)
140
2521
2019
1716
1412
9 8
715
029
2524
2220
1917
1411
109
160
3429
2726
2422
2018
1413
1117
039
3332
3027
2624
2218
1613
180
4442
3936
3332
3032
2123
1919
051
5047
4340
3935
3226
2319
200
6159
5551
4746
4238
3027
2321
071
6965
6055
5449
4536
3227
220
8381
7670
6462
5752
4237
3223
096
9387
8174
7266
6048
4236
240
110
107
100
9385
8376
6955
4942
250
125
122
114
106
9794
8779
6355
4826
014
213
812
912
011
010
798
8971
6354
270
160
156
146
135
124
120
111
101
8071
6128
017
917
516
315
213
913
512
411
390
7968
290
200
195
182
169
155
151
139
126
101
8976
300
223
217
203
188
173
168
154
140
112
9985
310
247
241
225
209
191
186
171
156
124
109
9432
027
226
624
823
021
120
518
917
213
712
110
433
030
029
227
325
323
322
620
818
915
113
311
434
032
932
130
037
825
524
822
820
716
514
612
535
036
035
132
830
427
927
124
922
718
115
913
736
039
238
335
833
230
529
627
224
819
717
414
937
042
741
738
936
133
232
229
626
921
518
916
338
046
445
242
339
236
034
932
229
323
320
517
639
050
249
045
842
539
037
934
831
725
322
319
140
054
353
049
545
942
240
937
634
327
324
120
741
058
657
253
449
545
544
140
637
029
525
922
342
063
161
557
553
349
047
543
739
831
727
924
043
067
866
164
857
352
651
147
042
834
130
025
844
072
771
066
361
556
554
850
445
936
632
227
745
077
976
071
065
960
558
754
049
239
234
527
746
083
381
376
070
564
762
857
852
641
936
931
747
089
086
881
175
269
167
061
756
144
839
433
948
094
992
686
580
273
771
565
859
947
742
036
149
010
1198
692
185
478
476
170
163
850
844
838
550
010
7510
4998
090
983
481
074
567
854
147
640
951
011
4211
1410
4196
588
686
079
172
057
450
643
452
012
1111
8211
0410
2494
091
284
076
460
953
646
153
012
8312
5211
7010
8599
696
789
081
064
656
848
854
013
5813
2512
3811
4810
5410
2394
285
768
360
251
755
014
3614
0113
0912
1411
1510
8299
690
672
263
654
756
015
1714
8013
8312
8311
7811
4310
5295
776
367
257
757
016
0115
6214
5913
5312
4312
0611
1010
1080
570
960
958
016
8816
4615
3914
2713
1012
7111
7010
6584
974
764
259
017
7717
3416
2015
0313
8013
3912
3211
2189
478
767
660
018
7018
2517
0515
8114
5214
0912
9711
8094
182
871
2
120
cR
oof a
ngle
dis2
5o30
o35
o40
o45
o50
o55
o60
o70
o80
o90
o
901Column spasing 1(cm)
140
2521
2020
2021
2019
1716
1515
029
2524
2526
2726
3127
2624
160
3431
3032
3334
3331
2726
2417
039
3837
3941
4240
3834
3229
180
4646
4548
5052
4946
4138
3619
056
5654
5760
6259
5649
4643
200
6666
6568
7173
7066
5855
5121
077
7876
7983
8682
7768
6460
220
9090
8893
9610
095
9080
7569
230
104
104
102
107
111
116
110
104
9286
8024
011
912
011
712
312
813
312
611
910
599
9225
013
613
613
314
014
615
114
413
612
011
310
526
015
415
415
115
816
517
216
315
413
612
811
927
017
417
417
017
818
619
318
417
415
314
413
428
019
519
519
120
020
921
720
619
517
216
115
029
021
721
821
322
323
324
223
021
819
218
016
830
024
224
323
724
925
926
925
624
221
420
018
631
026
826
926
327
528
729
828
426
823
722
220
632
029
629
729
030
431
733
031
329
626
124
522
833
032
532
732
033
534
936
334
532
628
827
025
134
035
735
835
136
738
339
837
835
831
629
627
535
039
139
238
440
241
943
541
439
134
532
430
136
042
642
841
843
845
747
545
142
737
735
332
937
046
446
645
547
749
751
749
146
541
038
435
838
050
450
549
451
854
056
153
350
444
541
738
839
054
654
753
656
158
560
857
854
648
225
242
140
059
059
257
960
663
265
762
459
152
148
845
541
063
663
862
565
468
270
967
463
756
252
749
042
068
568
767
370
473
776
372
568
660
556
752
843
073
673
972
375
778
982
078
073
765
161
056
844
079
079
377
681
284
788
083
679
169
865
460
945
084
684
983
187
090
794
389
684
774
870
165
246
090
590
888
893
097
010
0895
890
680
075
069
847
096
697
094
999
410
3610
7710
2396
885
480
074
548
010
3110
3410
1210
5911
0511
4810
9110
3291
185
479
449
010
9711
0110
7711
2811
7712
2311
6210
9997
090
984
650
011
6711
7111
4612
0012
5113
0012
3611
6910
3196
790
051
012
4012
4412
1712
7413
2913
8113
1312
4110
9510
2795
652
013
1513
2012
9113
5214
1014
6513
9313
1711
6210
8910
1453
013
9413
9813
6814
3314
9415
5314
7613
9612
3211
5410
7454
014
7514
8014
4815
1615
8216
4415
6214
7713
0412
2211
3755
015
6015
6515
3116
0316
7217
3816
5215
6213
7812
9212
0256
016
4716
5316
1716
9417
6618
3617
4416
5014
5613
6512
7057
017
3817
4517
0717
8718
6419
3718
4117
4115
3614
4013
4058
018
3318
3917
9918
8419
6520
4219
4118
3516
1915
1814
1359
019
3019
3718
9519
8420
7021
5120
4419
3317
0615
9914
8860
020
3120
3819
9420
8821
7822
6321
5120
3417
9516
8215
66
120
bR
oof a
ngle
dis2
5o30
o35
o40
o45
o50
o55
o60
o70
o80
o90
o
Column spasing 1(cm)
140
2521
2019
1717
1615
1312
1115
029
2524
2222
2221
1917
1514
160
3429
2827
2728
2624
2119
1717
039
3634
3334
3432
3026
2421
180
4444
4240
4142
3937
3129
2619
053
5350
4849
5047
4437
3431
200
6363
6057
5860
5652
4441
3721
074
7470
6769
7066
6152
4843
220
8686
8178
8081
7671
6156
5023
010
099
9490
9294
8882
7064
5824
011
411
310
810
410
610
810
194
8074
6725
013
012
912
311
812
112
311
510
791
8476
260
148
146
139
134
137
139
131
122
104
9586
270
167
165
157
151
154
157
147
137
117
107
9728
018
718
517
616
917
317
616
515
413
112
010
929
020
920
719
718
919
319
618
417
214
613
412
230
023
223
021
921
021
521
920
519
116
314
913
631
025
725
524
223
323
824
222
721
218
016
615
032
028
428
126
825
726
326
725
123
419
918
316
633
031
231
029
428
328
929
427
625
821
920
118
234
034
334
032
331
131
732
330
328
324
022
120
035
037
537
235
334
034
735
333
230
926
324
121
936
040
940
538
637
137
838
536
233
728
726
323
937
044
544
142
040
441
241
939
436
731
228
726
038
048
447
945
643
844
745
542
739
833
931
128
239
052
451
949
447
548
449
346
343
236
733
730
640
056
656
153
451
352
453
350
046
739
736
533
141
061
160
557
655
456
557
554
050
342
839
335
742
065
865
162
059
660
861
958
154
246
142
338
443
070
770
066
664
165
466
662
558
349
645
541
344
075
875
171
568
870
171
467
062
553
248
844
345
081
280
576
673
675
176
571
866
957
052
347
446
086
986
181
978
880
481
876
871
660
955
950
747
092
891
987
484
185
887
482
076
565
159
754
248
098
998
093
289
791
592
287
581
569
463
757
849
010
5410
4499
389
791
592
287
586
873
967
861
550
011
2011
1010
5610
1610
3610
5599
092
378
672
165
451
011
9011
7911
2210
7911
0111
2110
5298
183
576
669
552
012
6312
5111
9011
4511
6811
8911
1610
4188
681
373
753
013
3813
2512
6112
1312
3712
6011
8311
0393
986
178
154
014
1614
0313
3512
8413
1013
3312
5211
6799
391
282
755
014
9714
8314
1113
5813
8514
1013
2412
3410
5096
487
456
015
8215
6714
9014
3414
6314
8913
9813
0311
0910
1892
457
016
6916
5315
7315
1315
4415
7214
7513
7511
7110
7492
458
017
5917
4316
5815
9516
2716
5715
5514
5012
3411
3310
2759
018
5318
3617
4616
8017
1417
4516
3815
2713
0011
9310
8260
019
5019
3218
3817
6818
0318
3617
2416
0713
6812
5511
39
Dyn
amic
pre
ssu
re q
= 0
,8 k
N/m
2 (b
uild
ing
heig
ht 8
-20m
)
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Statics Predimensioning, Spar Spacing 120 cm
19
www.balkan.gr
W50
ACW
Area ratio of the facade module
Af , A
t, A
mArea ratio of the profiles
Ag
Area ratio of the glazing
Ap
Area ratio of the filling
Uf , U
m, U
t
Thermal transmission coefficient of the profiles (windows, mullions, transoms)
Ug
Thermal transmission coefficient of the glazing
Up
Thermal transmission coefficient of the filling
Ψg, Ψ
p
Length-related heat transmission coefficient of the
glazing or panel spacer
Ιg
Length of the visible glazing perimeter
Ιp
Length of the visible filling perimeter
Ucw
value (CURTAIN WALLING) to prEN 13947 prEn 13947 defines a method for determining the heat transmission coefficient Ucw of a curtain facade system consisting of glass fillings and / or non-transparent fillings in frames or sashes.
The heat transmission coefficient Ucw
of a curtain facade system is calculated using the following equation:
Window
Window
Frame
Note:The visible surfaces Ag and/or Ap are the smaller of the surfaces visible from the two sides.The total of the length lg and/or Ip is the total of the visible glazing or filling perimeter. If different lengths are visiblefrom the two viewing sides, the larger of the two has to be used.
Ucw
= ΣΑg
Ug + ΣA
pU
p + ΣΑf
Uf + ΣΙgΨg
+ ΣΙpΨp
ΣΑg + A
f + A
p
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50Calculation of the heat transmission coefficient Ucw
20
April 2009
W50
Apr
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50Nominal values of the heat transmission coefficient U
f
Nominal values of the heat transmission coefficient Uf
Transom
Mounting mullionFixed cross-section
The illustrated Uf values of the mullion-and-transom construction W 50 Were measured accordingto EN 12412-2 : 2009-07 and calculated accordingto EN 10077-2 : 2003-10
The allowance for the influence of the facadescrews has already been taken into account.
Screw Ø 5,5 mm Spacing approx 250 mm
Insert cross-sections
Moving cross-sectionsMullion with integrated sash, glazing bonded
Mullion
21
www.balkan.gr
W50
Mullion profiles, vertical (Level 3)
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Profiles
AH550-5114084 4,00 m delivery length
AH550-5114080 6,00 m delivery length
Mullion profile
Dev. anod.: 416 mm Weight: 1,85 kg/m
Dev. mech.: 210 mm Ix cm4: 62,76
2.5
7.110
50
46.4
11.5
100
107
7
83.5
80
87
7
11.5
46.4
10 7.1
2.5
50
63.5
10
10
30
37
PK 390 PK 391
20
10
26
10
PK 392PK 393
14
10
AH550-5114104 4,00 m delivery length
AH550-5114100 6,00 m delivery length
Mullion profile
Dev. anod.: 456 mm Weight: 2,05 kg/m
Dev. mech.: 250 mm Ix cm4: 107,53
ReinforcementAH550-5182080
AE013-000001-00 AE013-000002-00 AE013-929001-00 AE013-000003-00
ReinforcementAH550-5182100
( ) ( ) ( ) ( )AE013-000004-00
22
April 2009
W50
46.4
140
147
11.5
7
2.5
7.1
50
123.
5
10
50
7.1
2.5
7
11.5
127
120
46.4
103.
5
10
Stanzmaschinen
900 94050Einzelwerkzeug f�r
Matrizen und Stempel900 94036
f�r Stanzvorrichtung900 94070
50,4
11,5
MullionLevel 3
Mullion profiles, vertical (Level 3)
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Profiles
ΑΗ550-5114140
Mullion profile
Dev. anod.: 536 mm Weight: 2,45 kg/m
Dev. mech.: 330 mm Ix cm4: 243,04
ΑΗ550-5114124 4,00 m delivery length
ΑΗ550-5114120 6,00 m delivery length
Mullion profile
Dev. anod.: 496 mm Weight: 2,22 kg/m
Dev. mech.: 290 mm Ix cm4: 167,14
ReinforcementAH550-5182120
ReinforcementAH550-5182140
23
www.balkan.gr
W50
50
7.1
2.5
711
.5
167
160
45.8
143.
4
10
45
180 18
7
11.5
7
2.5
7.1
50
162
10
Mullion profiles, vertical (Level 3)
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Profiles
ΑΗ550-5114160
Mullion profile
Dev. anod.: 576 mm Weight: 2,85 kg/m
Dev. mech.: 370 mm Ix cm4: 352,81
ΑΗ550-5114180 (not permanently in stock)
Mullion profile
Dev. anod.: 616 mm Weight: 3,60 kg/m
Dev. mech.: 410 mm Ix cm4: 553,02
ReinforcementAH550-5182160
24
April 2009
W50
44.6
200 20
7
11.5
7
2.5
7.1
50
180.
8
10
30
Mullion profiles, vertical (Level 3)
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Profiles
Illustration shows clamped glazing
ΑΗ550-5115080
Mullion profile, vertical for sash installation
Dev. anod.: 384 mm Weight: 1,53 kg/m
Dev. mech.: 95 mm Ix cm4: 39,89
ΑΗ550-5114200 (not permanently in stock)
Mullion profile
Dev. anod.: 656 mm Weight: 4,23 kg/m
Dev. mech.: 450 mm Ix cm4: 790,30
25
W51 50053ΑΗ550-5150053
ΑΕ013-929036-20
ΑH550-5150015
25
www.balkan.gr
W50
15
160
7
2.5
7.1
25
95
200
33
11.5
3333
15
120
7
2.5
7.1
25
55
160
33
11.5
4.54.5
66.5 66.5
11,5
50,4
W51 50053
PK 426PK 426
W51 50053
Mullion profiles, vertical (Level 3)
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Profiles
Dies and punches for punching device
Illustration shows clamped glazing
ΑΗ550-5115120
Mullion profile, vertical for sash installation
Dev. anod.: 464 mm Weight: 1,93 kg/m
Dev. mech.: 135 mm Ix cm4: 111,40
ΑΗ550-5115160
Mullion profile, vertical for sash installation
Dev. anod.: 544 mm Weight: 2,32 kg/m
Dev. mech.: 270 mm Ix cm4: 249,00
Level 3
ΑΕ013-929036-20ΑΕ013-929036-20
ΑΗ550-5150053 ΑΗ550-5150053
26
April 2009
W50Curtain Wall system for facades and roofs
Thermal-insulated building construction Series W 50Profiles
Mullion corner profiles 90°, vertical (Level 3)
St tube 60/60
AH550-5113080
Mullion corner profiles 90o
Dev. anod.: 632 mm Weight: 2,85 kg/m
Dev. mech.: 160 mm Ix cm4: 83,60
AE013-929001-01
27
www.balkan.gr
W50
900 94036
T 902 00216
7.1
2.5
50
10
46.4
65.9 77
84
6.1
7
50,4
8,3
16
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Profiles
Transom profiles, vertical (Level 1)
AH550-5121077 + (not permanently in stock)
Transom profile for vertical application
Dev. anod.: 354 mm Weight: 1,645 kg/m
Dev. mech.: 254 mm Ix cm4: 55,84
MullionLevel 3
TransomLevel 1
TransomLevel 2
The figures apply to a self-powered doublepunching machine No. 900 94070
Dies and punches for 900 94070cutting out of the mullion profiles
Dies and punches for 900 94070 cutting out of the mullion profiles = 94037
Dies and punches for 900 94070cutting out of the mullion profiles = 94038
900 94050Punching tool for cutting out mullion, mountingmullion and transom profiles for use on HSP 110,Dyno 6, etc.
AH550-5184046
28
April 2009
W50
7
30.5
8.9
23.5
2.5
7.110
50
10.6
46.417.9
7
8.9
10.9
2.5
7.110
50
10
45.5
38.5
8.9
7
2.5
7.1
50
46.4
25.6
10
50
7.1
2.5
7
60.5
53.5
8.9
46.4
40.6T 902 00202
T 902 00203
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Profiles
ΑΗ550-5122011 + (not permanently in stock)
Transom profile for horizontal installation
Dev. anod.: 252 mm Weight: 0,69 kg/m
Dev. mech.: 72 mm Ix cm4: 0,61
Transom profiles, horizontal (Level 2)
ΑΗ550-5122024
Transom profile for horizontal installation
Dev. anod.: 276 mm Weight: 1,06 kg/m
Dev. mech.: 97 mm Ix cm4: 2,85
ΑΗ550-5122039
Transom profile for horizontal installation
Dev. anod.: 306 mm Weight: 1,20 kg/m
Dev. mech.: 127 mm Ix cm4: 9,09
ΑΗ550-5122054
Transom profile for horizontal installation
Dev. anod.: 336 mm Weight: 1,36 kg/m
Dev. mech.: 157 mm Ix cm4: 20,07
AH550-5184046
AH550-5184046
AH550-5184046
29
www.balkan.gr
W50
30
33
120
15
7.1
2.5
7 80
4.5
15
46.4
84.6
8.9
98.5 10
5.5
50
10 7.1
2.5
2.5
7.110
50
85.5
78.5
8.9
65.6
46.4
T 902 00205
T 902 00204
W51 50059
PK 413
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Profiles
Transom profiles, horizontal (Level 2)
T-connector 902 00185with drilling template 907 00027
AH550-5122079
Transom profile for horizontal installation
Dev. anod.: 385 mm Weight: 1,59 kg/m
Dev. mech.: 207 mm Ix cm4: 50,74
AH550-5122099
Transom profile for horizontal installation
Dev. anod.: 426 mm Weight: 1,92 kg/m
Dev. mech.: 247 mm Ix cm4: 101,07
T-connector 902 00185with drilling template 907 00027
AH550-5122080
Transom profile, horizontal for sash installation
Dev. anod.: 386 mm Weight: 1,50 kg/m
Dev. mech.: 95 mm Ix cm4: 41,10
ΑΕ013-929036-20
ΑH550-5150053
AH550-5184046
AH550-5184046
ΑH550-5184999
30
April 2009
W50
104.
6
46.4
2.5
7.110
50
125.
5
7
8.9
118.
5
138.
5
8.9
7
145.
5
50
10 7.1
2.5
46.4
124.
6
3
33
17
T 902 00206
T 902 00207
Glazing support AE011-903000-35from profile AH550-5156042Cut length 125 mm
Max. glazing weight 150 kg
per glazing support 75 kg
AH550-5122119
Transom profile for horizontal installation
Dev. anod.: 466 mm Weight: 2,12 kg/m
Dev. mech.:287 mm Ix cm4: 157,44
AH550-5122139
Transom profile for horizontal installation
Dev. anod.: 506 mm Weight: 2,30 kg/m
Dev. mech.: 327 mm Ix cm4: 229,37
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Profiles
Transom profiles, horizontal (Level 2)
AH550-5184046 AH550-5184046
31
www.balkan.gr
W50
45.8
144.
6
7.1
2.5
10
50
7
165.
5
158.
5
8.9
T 902 00208
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Profiles
Transom profiles, horizontal (Level 2)
AH550-5122159
Transom profile for horizontal installation
Dev. anod.: 546 mm Weight: 2,74 kg/m
Dev. mech.: 367 mm Ix cm4: 334,15
AH550-5184046
32
April 2009
W50
11.6
23.7
15 5330
425
19.5
15
2714
.5
W51 22080
PK 413
904 00075
W51
5001
5
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Profiles
Profiles
Adapter frame profile W51 50015 (C 35 anodised)and sash profile are screwed together after thepaint treatment and assembled to form a common sash on which the glazing is then bonded by an authorised gas company.
Corner connector AH900-TF558
Drilling template 907 00023
UV-
resi
stan
t edg
e bo
ndin
gal
way
s re
quir
ed
AH550-5150053
Sash profile for bonded glazing (flush surface with fixed glazing)
Dev. anod.: 241 mm Weight: 0,99 kg/m
Dev. mech.: 95 mm Ix cm4: 13,72
AH550-5150015
Adapter frame profile for window sash
Dev. anod.: 139 mm Weight: 0,31 kg/m
(always C 35 anodised)
Glazing support
Corner connector AH900-TF558
Drilling template 907 00023
Glazing support
AF004-904000-75
AΕ001-901003-45
AF004-904000-75
AE001-901003-45
AE013-929036-20
AH550-5122080
33
www.balkan.gr
W5016
726
2.5
780
50
1535
7.1
27
1530
Mul
lion
W51
150
80
W51
5001
5
6
2
7.1
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Profiles
Profiles
AH550-5150080
Glazing bar, vertical above and below sash glazings Dev. anod.: 255 mm Weight: 1,060 kg/m
Dev. mech.: 115 mm Ix cm4: 22,26
AH550-5150001
Glazing support profile for win-dow sash (glued glazing)
Dev. anod.: 54 mm Weight: 0,178 kg/m
Dev. mech.: 0 mm
Sash profile forbonded glazing
Sash profile forbonded glazing
Cut to length, 125 mm long = AE011-903000-31
Cut to length, 125 mm long = AE011-903000-33
AH550-5156053
Glazing support profile for win-dow sash (clamped glazing)
Dev. anod.: 124 mm Weight: 0,390 kg/m
Dev. mech.: 0 mm
AH550-5156042
Glazing support profile for fixed glazing horizontal half transom
Dev. anod.: 94 mm Weight: 0,350 kg/m
Dev. mech.: 0 mm
AH
550-
5115
080
Cut to length, 125 mm long = AE011-903000-35
34
April 2009
W50
6
50
AH550-5061012
Cover profile
Dev. anod.: 147 mm Weight: 0,240 kg/m
Dev. mech: 74 mm
AH550-5051006
Pressure profile
Dev. anod.: 155 mm Weight: 0,538 kg/m
Dev. mech: 50 mm
AH550-5061015
Cover profile
Dev. anod.: 159 mm Weight: 0,280 kg/m
Dev. mech: 80 mm
AH550-5057010
Pressure profile
Dev. anod.: 182 mm Weight: 0,410 kg/m
Dev. mech: 0 mm
10.5
49.3
50
1215
50
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Profiles
Profiles
35
www.balkan.gr
W50
97,7
50
Profiles, pressure and cover profiles
AH550-5061020
Cover profile
Dev. anod.: 177 mm Weight: 0,301 kg/m
Dev. mech: 90 mm
AH550-5063098 acces. AE005-000001-00
Cover profile
Dev. anod.: 293 mm Weight: 1,340 kg/m
Dev. mech: 206 mm
AH550-5067030
Pressure profile + not permanently in stock
Dev. anod.: 248 mm Weight: 0,880 kg/m
Dev. mech: 155 mm
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Profiles
50
20
30
50
36
April 2009
W50
AH275-5075027
Frame inserts for Series RG 75
Dev. anod.: 474 / 354* mm
Weight: 1,734 k
Dev. mech.: 104mm
Drilling template 907 00347Processing, seeSeries RGΒ block windows
Installation situation in facade W50
AH900-TF495
AH900-TF483
AH275-5075027
Frame inserts for Series RG 75
Dev. anod.: 474 / 354* mm
Dev. mech.: 104mm
Weight: 1,734 kg/m
Frame inserts, Series RG block windows for facade
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Profiles
37
www.balkan.gr
W50
16.5
19.5
105.550
10
4
38.5
8.5
28
4.5
70.5
75
24
56
30
73.5
72.5
E/P 901 569
E 901 458P 901 459
904 285
RG 1210
W50 75030
904 495 904 115
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Profiles
AH275-5075030
Frame inserts for Series RG 75
Dev. anod.: 474 / 339* mm Weight: 1,871 kg/m
Dev. mech.: 85mm
Drilling template 907 229Processing, seeSeries RG 75
Frame inserts, Series RG 75 facade
AH550-5075030
AE001-901569-00
AE001-901459-00
38
April 2009
W50Curtain Wall system for facades and roofs
Thermal-insulated building construction Series W 50Accessories
22.4
75
15 43.1
11.3 44.8
50 60.4
AH550-5150003
Frame inserts for flap window
Dev. anod.: 407 mm Weight: 1,488 kg/m
Dev. mech.: 43 mm
Frame inserts, Series W50 facade
Installation situation in facade W50
39
www.balkan.gr
W50
50 60.4
28.7 19.5
2564
11.811.5
2657
6
Installation situation in facade W50
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Profiles
AH275-280Sash inserts for flap window
Dev. anod.: 384 mm Weight: 1,681 kg/m
Dev. mech.: 92 mm Ix cm4: 10,51
Window inserts, Series W50 facade
40
April 2009
W50
12.1
7.1
8
AH550-9071008
Spacer profile 8mm
Dev. anod.: 69 mm
Dev. mech.: 16 mm
Weight: 0,120 kg/m
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Profiles
Auxiliary and connecting profiles
AH550-9071010
Spacer profile 10mm
Dev. anod.: 77 mm
Dev. mech.: 20 mm
Weight: 0,150 kg/m
AH550-5150001
Glass support for flap window (standard cw)
Dev. anod.: 54 mm
Dev. mech.: 0 mm
Weight: 0,178 kg/m
AH550-901
Joint for glass structural
Dev. anod.: 119 mm
Dev. mech.: 0 mm
Weight: 0,795 kg/m
AH550-902
Spacer for glass structural
Dev. anod.: 114 mm
Dev. mech.: 0 mm
Weight: 0,348 kg/m
AH550-903
Spacer for glass structural
Dev. anod.: 97 mm
Dev. mech.: 0 mm
Weight: 0,656 kg/m
AH550-5150002
Glass support for flap window(structural cw)
Dev. anod.: 83 mm
Dev. mech.: 0 mm
Weight: 0,261 kg/m
10
20
38
24.7
16
19.8
7.7
10
7.1
12.1
20
3.5 8.
5
14.7
3.5
23.2
20
10,7
20
25,3
41
www.balkan.gr
W50
50.0
29.5
44.1
34.4
AH550-5113001
Column addition for variable corner
Dev. anod.: 404,4 mm Weight: 1,228 kg/m
Dev. mech.: 80,3 mm
AH550-5113002
Pressure plate addition for 45o
Dev. anod.: 255,7 mm Weight: 0,794 kg/m
Dev. mech.: 77 mm
AH550-5113004
Pressure plate addition for 150o
Dev. anod.: 353,7 mm Weight: 1,013 kg/m
Dev. mech.: 81 mm
AH550-5113006
Column addition for for 150o
Dev. anod.: 83,4 mm Weight: 0,203 kg/m
Dev. mech.: 11,3 mm
AH550-5113003
Pressure plate addition for 60o
Dev. anod.: 217,5 mm Weight: 0,665 kg/m
Dev. mech.: 57,6 mm
AH550-5113005
Cover for pressure plate addition for 150o
Dev. anod.: 104 mm Weight: 0,163 kg/m
Dev. mech.: 29 mm
Variable angle profiles
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Profiles
42
April 2009
W50
62.7
82.7
102.
7
122.
7
142.
7
45.2
44.8
45.2
45.2
45.2
AH550-5182160Profile for reinforcement 902 00230 inmullion profile AH550-5114160
Weight: 3,20 kg/m
Profiles for accessory parts
AH550-5182140Profile for reinforcement 902 00229 in mullion profile AH550-5114140
Weight: 2,85 kg/m
AH550-5182120Profile for reinforcement 902 00228 in mullion profile AH550-5114120
Weight: 2,52 kg/m
AH550-5182100Profile for reinforcement 902 00227 in mullion profile AH550-5114100
Weight: 2,23 kg/m
AH550-5182080Profile for reinforcement 902 00226 in mullion profile AH550-5114080
Weight: 1,88 kg/m
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Profiles
43
www.balkan.gr
W50
AH550-5182200Profile for reinforcement inmullion profile AH550-5114200
Weight: 4,317 kg/m
AH550-5182180Profile for reinforcement inmullion profile AH550-5114180
Weight: 3,921 kg/m
Profiles for accessory parts
161,
2
44,4
44,4
180
44
44
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Profiles
44
April 2009
W50
AH550-5184002
Fast connector / mullion
Dev. anod.: 98 mm Weight: 0,518 kg/m
AE003-000001-00
Fast connector / transom
Dev. anod.: 268 mm
Dimension: 40mm
AH550-5184346
T-connector profile, variable for transom AH550-5122039 - AH550-5122139 for production of inclined transoms
Weight: 1,562 kg/m
53,1
64,5
45.8
29
10
R18.9
AH550-5184999
T-Connector for transom AH550-5122080
Weight: 2,56 kg/m
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Profiles
Profiles for accessory parts
45
www.balkan.gr
W50Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Profiles
AH550-5184046
T-Connector for transom AH550-5122039 - AH550-5122139
Dev. anod.: 217 mm Weight: 1,598 kg/m
AH550-5184045
T-Connector for transoms AH550-5122159
Dev. anod.: 215 mm Weight: 1,574 kg/m
AH550-5184001
Fast connector / transom
Dev. anod.: 193 mm Weight: 1,307 kg/m
AH550-5184044
T-Connector for transoms AH550-5122199
Dev. anod.: 214 mm Weight: 1,561 kg/m
Profiles for accessory parts
46
April 2009
W50
180
815
0
44
28
68
32 32
AH550-5182000
Mounting accessory for W50
Weight: 10,357 kg/m
Profiles for accessory parts
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Profiles
47
www.balkan.gr
W50
39
39.6
12
0.6
5±01
7.5
3
10
0.638
903 00033
903 271
903 00035
903 00040
903 00041
Keder
20
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Accessories
Joint sealing tape 10 x 3 mmRoll 10 m – impregnated
W51 5001Glazing support for sash with clamped glazing125 mm long (from profile W51 56039)
Glazing support for sash with bonded glazing125 mm long (from profile W51 56053) 885276
Glazing support for fixed glazing125 mm long (from profile W51 56042) 884454
Butyl adhesive tapeRoll 30 mm – double-sided
Butyl adhesive tapeRoll 10 mm - for the roof area
Connecting foil
Accessories
Width
Waterstrip
SG tan EPDM sealing strips to DIN 7864 as facade gasketFor sealing between facade elements and inner supporting structure(not water vapour-tight)904 855 Sealing strip. EPDM 150 mm wide with weatherstrip 20 m on roll904 857 Sealing strip. EPDM 250 mm wide with weatherstrip 20 m on roll904 859 Sealing strip. EPDM 300 mm wide with weatherstrip 20 m on roll904 861 Sealing strip. EPDM 330 mm wide with weatherstrip 20 m on roll904 864 Sealing strip. EPDM 500 mm wide with weatherstrip 20 m on roll
905 429 SG adhesive FA for EPDM sealing strips Required adhesion surface width 80- 100 mm Adhesive consumption 90 -110g (= approx. 0.08-0.10 ltr.) per running metre Tubular plastic bag (standard tubes) of 0.6 ltr (approx. 700 g)905 436 SG cleanser T for soiled surfaces (grease) Container with (approx. 850 g)
CAUTION! During adhesion, the instructions and hazard warnings of the manufacturer must be strictly observed!
48
April 2009
W50
904 00020904 00025904 00030904 00035 904 00315
47 5 3914
904 00040
Glass thickness Insulator Rabbed width Inner gasket Outer gasket Torx screw
12 mm PK 391 25 mm 904 00035 = 9 mm 904 00315 = 4 mm 906 900 = 35 mm
14 mm PK 391 25 mm 904 00030 = 7 mm 904 00315 = 4 mm 906 900 = 35 mm
16 mm PK 391 25 mm 904 00025 = 5 mm 904 00315 = 4 mm 906 900 = 35 mm
18 mm PK 391 25 mm 904 00020 = 3 mm 904 00315 = 4 mm 906 900 = 35 mm
18 mm PK 393 31 mm 904 00035 = 9 mm 904 00315 = 4 mm 906 902 = 45 mm
20 mm PK 393 31 mm 904 00030 = 7 mm 904 00315 = 4 mm 906 902 = 45 mm
22 mm PK 393 31 mm 904 00025 = 5 mm 904 00315 = 4 mm 906 902 = 45 mm
24 mm PK 393 31 mm 904 00020 = 3 mm 904 00315 = 4 mm 906 902 = 45 mm
24 mm PK 392 37 mm 904 00035 = 9 mm 904 00315 = 4 mm 906 901 = 50 mm
26 mm PK 392 37 mm 904 00030 = 7 mm 904 00315 = 4 mm 906 901 = 50 mm
28 mm PK 392 37 mm 904 00025 = 5 mm 904 00315 = 4 mm 906 901 = 50 mm
30 mm PK 392 37 mm 904 00020 = 3 mm 904 00315 = 4 mm 906 901 = 50 mm
28 mm PK 390 41 mm 904 00035 = 9 mm 904 00315 = 4 mm 906 903 = 55 mm
30 mm PK 390 41 mm 904 00030 = 7 mm 904 00315 = 4 mm 906 903 = 55 mm
32 mm PK 390 41 mm 904 00025 = 5 mm 904 00315 = 4 mm 906 903 = 55 mm
34 mm PK 390 41 mm 904 00020 = 3 mm 904 00315 = 4 mm 906 903 = 55 mm
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Glass thickness chart
CAUTION!When using sealing washers, observe thescrew length and the new screw insertion depth!!Glass thickness charts for sashes, please refer to the respective series for the sash used.
Mullion drawnrotated through 90°
Rabbet dimensions
49
www.balkan.gr
W50Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Seals
Sealing cordEPDM, black
14
904 00075
Gasket, internalEPDM, black
EPDM, black
Stop gasket
904 015
904 945
Gasket, internalEPDM, black
904 940
Gasket, externalEPDM, black
904 00040
Gasket, internalEPDM, black
904 00315
Gasket, externalEPDM, black
904 00035
Gasket, internalEPDM, black
904 00030
Gasket, internalEPDM, black
904 00025
Gasket, internalEPDM, black
904 00020
Gasket, internalEPDM, black
asymmetric
Glazingmax. 10° angle
asymmetricGlazing max. 10° angle
EPDM, black
AE004-000003-00
3
7
12
4
12
7
710°
10°
904 520
Gasket, externalSilicone, grey
7
777
3 5 7
EPDM, black
Gasket, external
904 540
4
7
9 4
7
24,5
5
4,8
Gasket for standard flap window
24.5
5
4.8
EPDM, black
AE004-000002-00
Gasket for structural flap window
20.6
5.9
EPDM, black
AE004-000001-00
Gasket for structural W50
2,64
5,3
AE004-904015-00
AE004-904001-00
Central gasketEPDM, black
AE004-904000-40 AE004-904940-00 AE004-904945-00
AE004-904000-20
AE004-904000-35 AE004-904000-75
AE004-904000-25 AE004-000-30
AE004-904003-15
5.8
19.7
AA205-101-00
Gasket for flap window
50
April 2009
W50
AE010-906116-00
AE010-906759-00
AE010-906779-00 AE010-906782-00
AE010-906761-00
AE010-906270-00 AE010-906609-00
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Screws
Screws of stainless steel
with cross headwith cross headwith cross head
with cross headwith cross headwith cross head
Self-tapping screw Fillister-head self-tapping screw
Cylinder screw
Countersunk self-tapping screw
AE010-906762-00Fillister-headself-tapping screwB4.2X25 with cross head
AE010-000006-00Fillister-headself-tapping screwB3,5X25 with cross head
AE010-000004-00Countersunkself-tapping screwB4.8X25 with cross head
AE010-906770-00Fillister-headself-tapping screwB4.8X32 with cross head
Countersunk screw Countersunk screw
Fillister-head self-tapping screw Countersunk self-tapping screwCountersunk self-tapping screw
Roof window hinges for connecting pin for Τ-joints
AE010-906752-00
AE010-906777-00
n3.5
25
51
www.balkan.gr
W50Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Screws
Countersunk self-tapping screwB 4,8 x 9,5with cross head
Sealing washerwith rubber coat (EPDM)for screw �Ø 4,8for pressure profiles
Ø
Roll pin, AIfor corner joints
Roll pin, AIfor T-jointsConnecting pin
for the connection with slide pieces
FWB facade screwTorx T25, with special threadØ 5,5x35mm
Accessories
906 797
906 901
906 900
905 150 905 160905 561
DIN 7982ISO 7050
AE010-000001-00 AE010-906901-00 AE010-000003-00
AE010-000005-00
AE010-000002-00
AE009-905160-00AE009-905150-00
60
FWB facade screwTorx T25, with special threadØ 5,5x50mm
FWB facade screwTorx T25, with special threadØ 5,5x60mm
FWB facade screwTorx T25, with special threadØ 5,5x55mm
FWB facade screwTorx T25, with special threadØ 5,5x45mm
52
April 2009
W50
AE005-000001-00
Cut?when?use?insulator?AE013-000002-00
Cut?when?use?insulator?AE013-000001-00
Fill?with?silicone
Fill?with?silicone
Use?screw?AE010-906777-00
AE005-000005-02
AE005-000001-00
Fold ventilation black, for W50
Plug decorative for AH550-5063098
AE005-000006-02
AE013-000006-00
Seal piece for dilatation W50
Square tube
Cut when use insulator or AE013-000001-00
Cut when use insulator or AE013-000002-00
Fill with silicone
Fill with silicone
Use screw AE010-906777-00
Accessories
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Screws
24
18
53
www.balkan.gr
W50
33
12
901 00520
22
26
20
8
16
10
Accessories
Rabbetdimensions
In sash area withclamped glazings,sash profile W 51 50053
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Accessories
AE013-929001-00 (PK 390)
Insulator profile 30 mm
Plastic
AE013-000002-00 (PK 392)
Insulator profile 26 mm
Plastic
AE013-000001-00 (PK 393)
Insulator profile 20 mm
Plastic
AE011-929790-00 (PK 79)
T-profile for sealing elements
Plastic
AE013-000003-00 (PK 391)
Insulator profile 14 mm
Plastic
AE013-929036-20(PK 426)
Insulating and supporting profile
Plastic
Rabbetdimensions
Rabbetdimensions
54
April 2009
W50 Curtain Wall system for fa�ades and roofsThermal-insulated building construction Series W 50
Corner connector
Corner connectors for flap window
Corner connector
A. AE001-000003-00B. ΑΑ001-022-00
for profile AH550-5150003
Connection with
5g adhesive 905 405
press AT038-015-00
Corner connector
AE001-000004-00
for profile AH275-280
Connection with
5g adhesive 905 405
Press AT038-015-00
A
Β
55
www.balkan.gr
W50Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Corner connectors
n7n4
5,2
8,3
907 00347
ProfilW50 75027
ProfileW50 60030W50 75030
905 140 905 150
901 911
901 00245
901 00250 901 00251
5
8,5
60,2
60
7
4
901 458 901 459
901 569
18
905 140905 160
Corner connector901 569for profile W50 75030
Connection with2 roll pins 905 160and 5g adhesive 905 405
with drilling template 907 229and drilling template 907 00469
Corner connector901 458for profile W50 75030
Connection with2 roll pins 905 140and 2g adhesive 905 405with drilling template 907 229and drilling template 907 00469
Pressta corner connector901 459
for profile W50 75030
Connection with2g adhesive 905 405
Corner connector901 00245for profile W50 75027
Connection with2 roll pins 905 150and 5g adhesive 905 405
Drilling template 907 00347
Corner connector901 00250for profile W50 75027
Connection with2roll pins 905 140and 2g adhesive 905 405
Drilling template 907 00347
Alternatively:Pressta corner connector901 00251
for profile W50 75027
Reinforcement angle bracket901 911
for profile W50 75027
Connection with
5g adhesive 905 405
Corner connector for roof windowThe corner connectors No.:901 595 / 605 / 635 / 645are illustrated with the corresponding
profiles.
Roll pin Roll pin
With drilling templates907 229 and 907 00469
ProfilesRoll pin Roll pin
With drilling templates
pinning
for pinning
Profiles
W50 75030
Corner connector
56
April 2009
W50
Reinforcement angle bracket of TF 481 in thecorner area of insulating profile PK 426Article No. 901 00520
Sash cutting dimension = Distance between centres + 1 mm
Drilling template
The corner connector must be installed with adhesive 905 405The cut surfaces must be sealed.
Cutting length 45,4 mm
Drilling template
Corner connector sash W51 50053 (using roll pin)
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Corner connector
57
www.balkan.gr
W50Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
T-connection
T-connection half transom to half mullion
T-connector
Drilling template
Transom axis
Transom contour drawn rotated through90° for illustration of the line course T-connector
Mu
llion
pro
file
Distance between centres
Drilling template
Mu
llion
pro
file
Transom profile
Cou
nter
sink
bor
es
If necessary: Tapered roll pin ISO 8745-5x20-St (stainless steel)
T-connector
Distance between centres
Transom cutting dimension = Distance between centres +20mm
Transom profile
58
April 2009
W50Cutting point, mullion corner, vertical with 190°, symmetrical
T-connector
Gla
zing
bar
Drilling template
Transom profile
Transom contour drawnrotated through90° for illustrationof the line course
Transom contour drawn rotatedthrough 90° for illustration ofthe line course
Mu
llion
pro
file
If necessary: Tapered roll pin ISO 8745-5x20-St (stainless steel)
Distance between centres
Transom cutting dimension = Distance between centres +20mm
Mu
llion
pro
file
Drilling template
Transom profile
T-connector
T-connector
Gla
zing
bar
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
T-connection
59
www.balkan.gr
W50Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
T-connection
T-connection transom to mullion
Schematic viewFurther details on the followingpages of the catalogue
T-connector
Transom contour drawn rotated through90° for illustration of the line course
Transom cutting dimension = Distance between centres - 18mm
Distance between centres
Transom profile
T-co
nnec
tor
Mullion profile
Dri
lling
tem
plat
e
60
April 2009
W50Curtain Wall system for facades and roofs
Thermal-insulated building construction Series W 50T-connection
T-connection with T-connector
Drilling templates for transom endNo. 907 00106 for mullion holesNo. 907 00106 for T-connector to mullionNo. 901 00101Punching machine 900 94070 with dieand punch for mullion No. 900 94036
Vertical loadper T-connector
max. 75 kg Cut to lengthT-connector
Transom chamber
Butyl adhesive tape 12 x 50 mmfrom Article No. 903 00040
T-connection – schematic view
T-connection with T-connector
61
www.balkan.gr
W50Curtain Wall system for facades and roofs
Thermal-insulated building construction Series W 50T-connection
T-connection transom (Level 2) to mullion (Level 3)
Mullion, verticalLevel 3
Transom, Level 2Mullion, vertical
Level 3
Transom, Level 2
Transom, horizontalLevel 2
Punching machine 900 94070 with
tool 900 94036
Bu
tyl a
dhes
ive
tape
of 9
03 0
0040
Bu
tyl a
dhes
ive
tape
of 9
03 0
0040
62
April 2009
W50 Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
T-connection
T-connection transom (Level 2) to mullion (Level 3)Scale 1:2
904
0004
0
63
www.balkan.gr
W50Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
T-connection
T-connection transom (Level 2) to mullion (Level 3)
Scale 1:2
W90
710
10
64
April 2009
W50 Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
T-connection
T-connection transom (Level 2) to mullion (Level 3)
902 00202T-connector Transom W51 22039to mullion W51 14 ***
Connection with2 roll pins 905 1602 screws 906 7525 g adhesive 905 405
Drilling template 907 00106Bores in horizontal transom forscrews and roll pins
Drilling template 907 00101Bores in vertical mullion forattachment of the T-connectors
Mullion profile, verticalPunching machine 900 94070with die and knife 900 94036Punch-out on mullion profile
Mullion
of profile
Mullion,Level 3
Mullion
of profi leTransom, Level 2
902 00203T-connector Transom W51 22054to mullion W51 14 **
Connection with2 roll pins 905 1602 screws 906 7525g adhesive 905 405
Drilling template 907 00106Bores in horizontal transomfor screws and roll pinsDrilling template 907 00101Bores in vertical mullion for attachment of the T-connectors
Mullion profile, verticalPunching machine 900 94070with die and knife 900 94036Punch-out on mullion profile
65
www.balkan.gr
W50Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
T-connection
T-connection transom (Level 2) to mullion (Level 3)
of profi le
Mullion
Transom
of profi le
Mullion
Transom
902 00204T-connectorTransom W51 22079 tomullion W51 14080
Connection with2 roll pins 905 1602 screws 906 75210g adhesive 905 405
Drilling template 907 00106Bores in horizontal transom forscrews and roll pins
Drilling template 907 00101Bores in vertical mullion for attachmentof the T-connectorsMullion profile, vertical
Punching machine 900 94070with die and knife 900 94036Punch-out on mullion profile
902 00207T-connectorTransom W51 22099 tomullion W51 14100
Connection with2 roll pins 905 1602 screws 906 75215g adhesive 905 405
Drilling template 907 00106Bores in horizontal transom forscrews and roll pins
Drilling template 907 00101Bores in vertical mullion for attachmentof the T-connectors
Mullion profile, verticalPunching machine 900 94070with die and knife 900 94036Punch-out on mullion profile
66
April 2009
W5031
.033
5.08
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
T-connection
T-connection transom (Level 2) to mullion (Level 3)
Mullion
Transom
Mullion
Transom
of profi le
of profi le
902 00206T-connectorTransom W51 22119 to mullionW51 14120
Connection with2 roll pins 905 1602 screws 906 75220 g adhesive 905 405
Drilling template 907 00106Bores in horizontal transom forscrews and roll pins
Drilling template 907 00101Bores in vertical mullion for attachmentof the T-connectorsMullion profile, verticalPunching machine 900 94070with die and knife 900 94036Punch-out on mullion profile
902 00207T-connectorTransom W51 22139 to mullionW51 14140
Connection with2 roll pins 905 1602 screws 906 75220 g adhesive 905 405
Drilling template 907 00106Bores in horizontal transom forscrews and roll pins
Drilling template 907 00101Bores in vertical mullion for attachmentof the T-connectors
Mullion profile, verticalPunching machine 900 94070with die and knife 900 94036Punch-out on mullion profile
67
www.balkan.gr
W5031
.033
5.09
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
T-connection
902 00208T-connectorTransom W51 22159 to mullion W51 14160
Connection with 2 roll pins 905 1602 screws 906 752 30 g adhesive 905 405
Drilling template 907 00106Bores in horizontal transomfor screws and roll pins
Drilling template 907 00101Bores in vertical mullion for attachment of the T-connectorsMullion profile, vertical
Punching machine 900 94070with die and knife 900 94036Punch-out on mullion profile
902 00209T-connectorTransom W51 22179 tomullion W51 14180
Connection with 2 roll pins 905 1602 screws 906 75235 g adhesive 905 405
Drilling template 907 00106Bores in horizontal transomfor screws and roll pins
Drilling template 907 00101Bores in vertical mullion for attachment of the T-connectorsMullion profile, vertical
Punching machine 900 94070with die and knife 900 94036Punch-out on mullion profile
T-connection transom (Level 2) to mullion (Level 3)
Mullion
of profile
Transom
Mullion
Transom
of profile
68
April 2009
W50
50,4
16
36
52
37,8
Mullion
MullionLevel 3
TransomLevel 2
of profileW51 84046
of profileW51 84046
Pfosten
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
T-connection
Transom
Mullion
T-connectorTransom W51 22* tomullion W51 14*
Connection with2 roll pins 905 1601 screws 906 75235 g adhesive 905 405
Drilling template 90700106Bores in horizontal transomfor screws and roll pins
Drilling template 907 00101Bores in vertical mullion for attachmentof the T-connectors
Mullion profile, verticalPunching machine 900 94070with die and knife 900 94036
Punch-out on mullion profile
T-connection transom (Level 2) to mullion (Level 3)
T-connectorTransom W51 22* tomullion W51 14*
Connection with2 roll pins 905 1602 screws 906 75235 g adhesive 905 405
Drilling template 90700106Bores in horizontal transomfor screws and roll pins
Drilling template 907 00101Bores in vertical mullion for attachmentof the T-connectors
Mullion profile, verticalPunching machine 900 94070with die and knife 900 94036
Punch-out on mullion profile
69
www.balkan.gr
W50
50.4
65,5
36
15,6
13,7
8,3
50,4
65,5
36
3615
,613
,7
8,3
4,5
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
T-connection
T-connection transom (Level 1) to transom (Level 2)
902 00216T-connector
Transom W 51 21077 to
transom W 51 22079
Connection with
2 roll pins 905 160
2 screws 906 752
10 g adhesive 905 405
Drilling template 907 00106
Bores in vertical transom for
screws and roll pins
Drilling template 907 00101
Bores in horizontal transom
for attachment of the
T-connectors
Transom, horizontal
Punching machine 900 94070
with die and knife 900 94037
Punch-out on horizontal
transom
Transom (1)
T-connector of profileW51 84046
Transom (2)
Lower recess only if the verticaltransom is continued
Transom W51 21077vertical
T-connector of profileW51 84046
Transom (2)
902 00216
Transom W51 22079horizontal
70
April 2009
W50 Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
T-connection
Rapid Connection
AH550-5184002-00
AH550-5184001-00
AE005-000003-02
AE005-000002-02
AH550-22039AH550-22059
AH550-22079
AH550-22099
AH550-22119
AH550-22139
AH550-22159
AE005-000003-02
Plug transom cover
Plug transom cover
AE010-000006-00
1
2
34
71
www.balkan.gr
W50
Rapid Connection
50.4
22,5
20.5
43
37.8
10
104
17.1
76
10.9
11.5
66.6
17,1
10.9
10.9
10
31.8
94.6
W51 84001W51 84002T-connectorTransom W51 22119 tomullion W51 14***
Connection with2 screws 906 7544 screws 906 7611 plug transom coverAE005-000003-0210 g adhesive 905 405
Drilling template 907 00106Bores in vertical transom forscrews and roll pins
Drilling template 907 00101Bores in horizontal transomfor attachment of theT-connectors
Transom, horizontalPunching machine 900 94070with die and knife 900 94037Punch-out on horizontal transom
W51 84001W51 84002(with profile W90 71010)
T-connectorTransom W51 22119 tomullion W51 14***
Connection with2 screws 906 7544 screws 906 7611 plug transom coverAE005-000003-0210 g adhesive 905 405
Drilling template 907 00106Bores in vertical transom forscrews and roll pins
Drilling template 907 00101Bores in horizontal transomfor attachment of theT-connectors
Transom, horizontalPunching machine 900 94070with die and knife 900 94037Punch-out on horizontal transom
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
T-connection
MullionLevel 3
TransomLevel 2
72
April 2009
W50
Mullion W51 14100
Transom W51 22099
Transom W51 22079
Mullion W51 14080
W51 84001
11.
17.35622
84.2
18.3
11.1
22 36
65.2
50.4
27
W51 84002
50.4
27
W51 84001
W51 84002
W51 84001W51 84002T-connectorTransom W51 22079 tomullion W51 14080
Connection with2 screws 906 7614 screws 906 7771 plug transom coverAE005-000002-02
Drilling template 90700106Bores in horizontal transomfor screws and roll pins
Drilling template 907 00101Bores in vertical mullion for attachmentof the T-connectors
Mullion profile, verticalPunching machine 900 94070with die and knife 900 94036
Punch-out on mullion profile
T-connection transom (Level 2) to mullion (Level 3)
W51 84001W51 84002T-connectorTransom W51 22099 tomullion W51 14100
Connection with2 screws 906 7614 screws 906 7771 plug transom coverAE005-000003-02
Drilling template 90700106Bores in horizontal transomfor screws and roll pins
Drilling template 907 00101Bores in vertical mullion for attachmentof the T-connectors
Mullion profile, verticalPunching machine 900 94070with die and knife 900 94036
Punch-out on mullion profile
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
T-connection
73
www.balkan.gr
W50
Transom W51 22139
Mullion W51 14140
Mullion W51 14120
Transom W51 22119
96 17.122
11. 124,0
76 17.122
11.1 104,0
50.4
27
W51 84001
W51 84002
50.4
27
W51 84001
W51 84002
T-connection transom (Level 2) to mullion (Level 3)
W51 84001W51 84002T-connectorTransom W51 22119 tomullion W51 14120
Connection with2 screws 906 7614 screws 906 7771 plug transom coverAE005-000003-02
Drilling template 90700106Bores in horizontal transomfor screws and roll pins
Drilling template 907 00101Bores in vertical mullion for attachmentof the T-connectors
Mullion profile, verticalPunching machine 900 94070with die and knife 900 94036
Punch-out on mullion profile
W51 84001W51 84002T-connectorTransom W51 22139 tomullion W51 14140
Connection with2 screws 906 7614 screws 906 7771 plug transom coverAE005-000003-02
Drilling template 90700106Bores in horizontal transomfor screws and roll pins
Drilling template 907 00101Bores in vertical mullion for attachmentof the T-connectors
Mullion profile, verticalPunching machine 900 94070with die and knife 900 94036
Punch-out on mullion profile
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
T-connection
74
April 2009
W50
Mullion W51 14180
Transom W51 22179
Transom W51 22159
Mullion W51 14160
16.113622
11.6 162,5
11.1
17.111622
144,0
50.4
27
W51 84001
W51 84002
50.4
27
W51 84001
W51 84002
W51 84001W51 84002T-connectorTransom W51 2259 tomullion W51 14160
Connection with2 screws 906 7614 screws 906 7771 plug transom coverAE005-000002-02
Drilling template 90700106Bores in horizontal transomfor screws and roll pins
Drilling template 907 00101Bores in vertical mullion for attachmentof the T-connectors
Mullion profile, verticalPunching machine 900 94070with die and knife 900 94036
Punch-out on mullion profile
T-connection transom (Level 2) to mullion (Level 3)
W51 84001W51 84002T-connectorTransom W51 22179 tomullion W51 14180
Connection with2 screws 906 7614 screws 906 7771 plug transom coverAE005-000003-02
Drilling template 90700106Bores in horizontal transomfor screws and roll pins
Drilling template 907 00101Bores in vertical mullion for attachmentof the T-connectors
Mullion profile, verticalPunching machine 900 94070with die and knife 900 94036
Punch-out on mullion profile
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
T-connection
75
www.balkan.gr
W50
300
25
4
902 00226
902 00227
902 00228
902 00229
902 00230
M. 1:1
906
830
906
270905 561
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Reinforcement
Reinforcement, vertical butt joint mullion/mullion
Reinforcement for mullionW 51 14080Length 300 mmas bar 6,0 m longNo.: W51 82080
Reinforcement for mullionW 51 14100Length 300 mmas bar 6,0 m longNo.: W51 82100
Reinforcement for mullionW 51 14120Length 300 mmas bar 6,0 m longNo.: W51 82120
Reinforcement for mullionW 51 14140Length 300 mmas bar 6,0 m longNo.: W51 82140
Reinforcement for mullionW 51 14160Length 300 mmas bar 6,0 m longNo.: W51 82160
Shown in reduced size
ReinforcementNumber and spacing ofthe bolts according tostatics requirements
Join
t
76
April 2009
W50 Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Variable T-connection
Variable T-connection, transom (Level 2) to mullion (Level 3)
•
77
www.balkan.gr
W50Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Variable T-connection
Variable T-connection, transom (Level 2) to mullion (Level 3)
Transom
Mu
llion
Tran
som
Insulator PK 390 Insulator PK 390
Transom (level 2)
Mullion (level 3)
Tran
som
Transom
Mu
llion
Insulator PK 390 Insulator PK 390
Transom (level 2)
Mullion (level 3)
902 00264T-connector, variableTransom W51 22079 to mullionW51 14080
Connection with3 roll pins 906 7701 screws 906 90110 g adhesive 905 405
Bores in the inclined transom for screws according to the angle
Drilling template 907 00101Bores in vertical mullion for attachment of theT-connectors
902 00265T-connector, variableTransom W51 22099 to mullionW51 14100
Connection with3 roll pins 906 7701 screws 906 90115 g adhesive 905 405
Bores in the inclined transom for screws according to the angle
Drilling template 907 00101Bores in vertical mullion for attachmentof the T-connectors
78
April 2009
W50Curtain Wall system for facades and roofs
Thermal-insulated building construction Series W 50Variable T-connection
Variable T-connection, transom (level 2) to mullion (level 3)
902 00266T-connector, variableTransom W51 22119 Tomullion W51 14120
Connection with:3 screws 906 7701 screw 906 90120 g adhesive 905 405
Bores in the inclined transom for screws according to the angle
Drilling template 907 00101Bores in vertical mullion for attachmentof the T-connector
902 00267T-connector, variableTransom W51 22119 Tomullion W51 14120
Connection with:3 screws 906 7701 screw 906 90125 g adhesive 905 405
Bores in the inclined transom for screws according to the angle
Drilling template 907 00101Bores in vertical mullion for attachmentof the T-connector
Transom
Mu
llion
Tran
som
Insulator PK 390 Insulator PK 390
Transom (level 2)
Mullion (level 3)
Transom
Mu
llion
Tran
som
Insulator PK 390 Insulator PK 390
Transom (level 2)
Mullion (level 3)
79
www.balkan.gr
W50Curtain Wall system for facades and roofs
Thermal-insulated building construction Series W 50Drilling template
Drilling template 907 00101 - Schematic viewPositioning of the templateon the mullion profile
Mullion profileLevel 2
Positioning of the templateon the disengagedmullion profile
Mullion profileLevel 2
80
April 2009
W50Curtain Wall system for facades and roofs
Thermal-insulated building construction Series W 50Drilling template
Positioning of the template onthe mullion profile (2)
Mullion profileLevel 2
Mullion profileLevel 2
Shim
Drilling template 907 00101 - Schematic viewPositioning of the templateon the disengaged mullionprofile (2)
81
www.balkan.gr
W50Curtain Wall system for facades and roofs
Thermal-insulated building construction Series W 50Τ-connection
T-connection transom / half-mullion to half mullion
3039.5
37.3
5.2
37.9
43.5
907 00027
Rie
gelp
rofil
e
907 00028
906 609
902 00185
902 00186
In order to illustratethe course of the line,the profiles are drawnrotated through 90°
T-connector
T-connector
Drilling template
Drilling template
Tran
som
pro
files
82
April 2009
W50 Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Cutting points
Cutting point, horizontal - cutting of transom W51 22080
Glazing transom W51 50080 verticalabove and below sash panels
Transom W51 22080Horizontal
Mu
llion
W51
150
80 v
ertic
al
Cutting allowance
Glazing transom W51 50080 verticalabove and below sash panels
Cutting allowance = Matrix dimension + 20 mm
In o
rder
to il
lust
rate
the
cou
rse
of th
e lin
e,
the
prof
iles
are
draw
n ro
tate
d th
rou
gh 9
0o
T-co
nnec
tor
902
0018
5
Mu
llion
W51
150
80 v
ertic
alM
ulli
on W
51 1
5080
ver
tical
Axis of the bore
Transom axis
Transom W51 2
2080
Horizontal
83
www.balkan.gr
W50Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Installation of insulator
Installation of insulator PK 426 in sash area (clamped glazing)
Corner connector901 00520from profileTF 481
Notching
Axis
Axis
Notchings in the horizontal parts PK 426
Transom Transom
84
April 2009
W50
25
25
16
..
99
.5
1.
25
.
.
.
5
1
25
5
1
25L
= A
- 1
8 m
m
L =
A -
52
mm
L =
A -
60
mm
L =
A -
18
mm
W50
570
08
PK 390
PK 3
90
PK 390
W50
570
08
W50
610
15
W50
610
20
L = A - 18 mm
L = A - 60 mm
L = A - 52 mm
904
0004
0
904
0003
0
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Cutting to length
Cut lengths
Cover profile
Insulator profile + transom profile
Cover profile
Cut lengths (L)
Axi
s (A
)
Axi
s (A
)
Cov
er p
rofil
e
Cov
er p
rofil
e
Pre
ssu
re p
rofil
e
Pre
ssu
re p
rofil
e
Insu
lato
r pr
ofile
Tran
som
profi l
e
Tran
som
profi l
e
Mullion
Axis (A)Axis (A)
Axis (A)
85
www.balkan.gr
W50Curtain Wall system for facades and roofs
Thermal-insulated building construction Series W 50Facade connections
Facade connections
Schematic representation ofvarious possibilities
Movable bearing Movable bearing Movable bearing
Fixed bearing Fixed bearingFixed bearing
Movable bearing Movable bearing
Fixed bearing Fixed bearingFixed bearing
Movable bearing
86
April 2009
W50Curtain Wall system for facades and roofs
Thermal-insulated building construction Series W 50Cutting points
Overview of cutting points
Mu
llion
, lev
el 3
Mu
llion
, lev
el 3
Mu
llion
, lev
el 3
Mu
llion
, lev
el 3
Level 2Continuous transom
Level 2Continuous transom
Level 2Transom
Tran
som
, lev
el 1
betw
een
the
hori
zont
altr
anso
ms,
leve
l 2
Mullion, verticalLevel 3
Transom, horizontalLevel 2
Transom, verticalLevel 1
Mullion
87
www.balkan.gr
W50Curtain Wall system for facades and roofs
Thermal-insulated building construction Series W 50Cutting points
Cutting point, mullion, vertical (Level 3)
Transom
Transom
Transom
Transom
Transom
Transom
Further mullion profiles up to 200 mm installation depth, see profile illustrations
Further glazingthicknesses, seeGlazing thickness chart
88
April 2009
W50 Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Cutting points
Cutting point, mullion corner, vertical with 160°, symmetrical
CAUTION!Due to the excessive angle of the glazings, the verticalpressure profiles may only be tightened until they fulfiltheir sealing function and not too tightly.
Transom contour drawnrotated through90° for illustrationof the line course
Transom
89
www.balkan.gr
W50
Transom contour drawnrotated through90° for illustrationof the line course
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Cutting points
Cutting point, mullion corner, vertical with 190°, symmetrical
CAUTION!Due to the excessive angle of the glazings, the verticalpressure profiles may only be tightened until they fulfiltheir sealing function and not too tightly.
Transom
90
April 2009
W50 Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Cutting points
Cutting point, transom, horizontal (Level 2)
Drainage of the transomThe transom is drained via at least 2 bores(dia. 6 mm) or slots 20x5 drilled in the retaining profile and cover strip
Distance max. 600 mm
Distance between centres
Further glazing thicknesses,see Glazing thickness chart
Glazing support Nr. 903 00035
Transom drainageAt least 2 holes Φ6 mm or slots20x5 mm
Further transom profiles in stepsof 20 mm up to an installation depth of198.5 mm - see profile illustrations
91
www.balkan.gr
W50Cutting point, vertical, sashes with bonded glazings
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Cutting points
17,3 43,1 50
8097
,6
110,4
649
204,
6
284
8
2
35
AH550-5063098
W50 57010
W5114080AH550-5150003
AH
275-
280
92
April 2009
W50
Fl�g
elzu
schn
itt =
Ras
term
a� +
1 m
m
1515
34
2727
30
1553
12215
66.5
66.5
4242
50
137
5151.5 78.5
19.5
4.5
267 4
37
11
50
19.5
4.5 11
15 5W
50 6
1015
W50
610
20W
50 6
1020
W50
610
15
Rie
gel
Rie
gel
W51
220
79W
51 2
2079
Rie
gel
W51
220
80
Rie
gel
W51
220
80
W51
150
80W
51 1
5080
W51
5001
5W
5150
015
904
0003
090
4 00
030
W51
500
53W
51 5
0053
90400075
90400075
904 00100
904 00100
PK 426
PK 426
904
0031
590
4 00
315
W50
570
10W
50 5
7010
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Cutting points
Cutting point, horizontal, sashes with bonded glazings
Tran
som
Tran
som
Tran
som
Tran
som
CA
UTI
ON
! Min
. gri
d di
men
sion
= 7
50m
m
The
glaz
ing
plan
es in
the
win
dow
sas
han
d in
the fi x
ed p
anel
are
fl us
h
Hor
izon
tal c
ut
Sas
h si
ze =
Gri
d di
men
sion
+ 1
mm
93
www.balkan.gr
W50Curtain Wall system for facades and roofs
Thermal-insulated building construction Series W 50Cutting points
Cutting point, vertical, sashes with bonded glazings
Vertical cut
Sas
h si
ze =
Gri
d di
men
sion
+ 1
mm
The glazing planes in the window sashand in the fixed panel are flush
10 mm dia. for drainage
Rec
ess
Rec
ess
Rec
ess
Rec
ess
94
April 2009
W50 Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Cutting points
Cutting point, horizontal, sashes with bonded glazingsH
oriz
onta
l cut
The
glaz
ing
plan
e in
the
win
dow
sas
his
off
set f
rom
the
fixed
pan
el!
904
0002
5
W51 14080
904
0031
5
PK 390
AE004-000003-00
AH550-5150003
AA205-101-00
AH550-5150003
904
0003
590
4 00
035
W51 14080
AH275-280
AH275-280
5060
.4
12428964
2119
8.51.5
5043
.15.
511
.850
43.1
5.5
11.8
15
12428578.51.5
10
17 34.2
132
11.8
60.4
11.8
34.2
25
95
www.balkan.gr
W50
904
0002
5
904
0031
5
PK 390
AE004-000003-00
AA205-101-00
W51 22079
AH550-5150003
AH275-280
904
0003
5
W51 22079
AH550-5150003
AH275- 280
904
0003
5
AA205-101-00
904
0002
5
904
0031
5
PK 390
W51 56042
5011
.8
12 4 28 64
2119
8.5
5043
.15.
511
.850
43.1
5.5
11.8
1511
.812 4 28 5 78.5
34.2
10
1717
3
1321.5
1.5
60.4
34.2
60.4
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Cutting points
Cutting point, vertical, sashes with bonded glazings
The
glaz
ing
plan
e in
the
win
dow
sas
his
off
set f
rom
the
fixed
pan
el!
Vert
ical
cut
96
April 2009
W50
AE004-000001-00
W51 50003
904
0003
590
4 00
035
904
0002
590
4 00
025
W51 14080
W51 14080
904 00035
904 00035
43.1
5.5
11.8
43.1
5.5
11.8
32578.51.5
28964
2
14
1010
12.6
48.3
85.4
5050
1010
12.6
48.3
85.4
AH275-280
AH275-280
AH550-5150003
AH550-5150003
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Cutting points
Cutting point, horizontal, sashes with bonded glazingsH
oriz
onta
l cut
The
glaz
ing
plan
e in
the
win
dow
sas
his
off
set f
rom
the
fixed
pan
el!
AH550-5114080
AH550-5114080
97
www.balkan.gr
W50
The
glaz
ing
plan
e in
the
win
dow
sas
his
off
set f
rom
the
fixed
pan
el!
Vert
ical
cut
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Cutting points
Cutting point, vertical, sashes with bonded glazings
98
April 2009
W50
90°
W51 22079
W50 57010
W50 61012
W51
220
79
W50
570
10W
50 6
1012
AH550-
5113
002
AH550-5114100
Section of A turning mode (45o angle)
50,017,0
44,1
W51 14100
W50 57010
W50 61012
W51 22119
W51
220
79
W50
570
10W
50 6
1012
135°
AH550-
5113
002
AH550-5114100
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Cutting points
99
www.balkan.gr
W50Section of A turning mode (60o angle)
50,07,3
34,3
7,3
34,3
W51 22079
W50 57010
W50 61012
W51 22079
W50 57010
W50 61012
120°
AH550-5113003
AH550-5114100
50,07,3
34,3
W51 22079
W50 57010
W50 61012
W50 57010
W50 61012
W51 22119
150°
AH550-5113003
AH550-5114100
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Cutting points
100
April 2009
W50
W51 14120
11,3
15
10,2
150°
32
2910 1016 16
AH550-5114104
AH550-5113004
Section of A turning mode (150o angle)
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Cutting points
101
www.balkan.gr
W50
80
137
51537
50
1535
50
50
1535
50
1111
11
7 26 4
11
4267
W51
500
80W
51 5
0080
W51
220
79
Rie
gel
W51
220
80
Rie
gel
W51
220
80
Rie
gel
W51
220
79
Rie
gel
W50
610
15W
50 6
1020
W51
150
80W
51 1
5080
W50
610
20W
50 6
1015
PK 390
PK 390
904
0003
090
4 00
030
Dehn ba
nd
Dehn
band
904
0031
590
4 00
315
W50
570
10W
50 5
7010
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Cutting points
Cutting point, horizontal, below or above the window sashH
oriz
onta
l cut
Tran
som
Tran
som
Tran
som
Tran
som
Vulc
anis
ed fr
ame
Vulc
anis
ed fr
ame
The
glaz
ing
plan
e in
the
win
dow
sas
his
off
set f
rom
the
fixed
pan
el!
102
April 2009
W50
50
137
51.5 78.5 37 15
26 47
6.1
122
51553.1 48.9
11
37
47 26
425
4.5
19.5
66.5
78.51.5 15 5
30 4
5050
1111
904
0010
0
Tran
som
W51
220
79
W50
610
15W
50 6
1020
Mul
lion
W51
140
80
Tran
som
W51
220
79W
51 2
2079
Tran
som
W51
220
80
Tran
som
W51
150
80
W50
610
20W
50 6
1015
W51
500
53
904
0003
0
PK 390
906
901
904
0031
590
4 00
315
904
0003
0
W50
570
10W
50 5
7010
90400075
W51
5001
5
15
137
PK 426
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Cutting points
Cutting point, horizontal, sash/fixed glazingH
oriz
onta
l cut
The
glaz
ing
plan
e in
the
win
dow
sas
his
off
set f
rom
the
fixed
pan
el!
Tran
som
Tran
som
Tran
som
Tran
som
Mu
llion
103
www.balkan.gr
W50
80
137
51537
47 26
37
47 26
78.51.5
15 5
137
50
11
1535
50
11
50
1111
50
7 426
153778.51.5 5
137
Pfos
ten
W51
140
80
Rie
gel
W51
220
79R
iege
lW
51 2
2079
W50
610
15W
50 6
1020
W51
500
80
W50
610
15
Rie
gel
W51
220
79
Rie
gel
W51
220
80
Hor
izon
tals
chni
tt
W51
150
80
W50
610
20
906
901
PK 390
Dehn ba
nd
PK 390
904
0003
0
904
0031
590
4 00
315
W50
570
10W
50 5
7010
904
0003
0
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Cutting points
Cutting point, horizontal, below or above the window sashH
oriz
onta
l cut
Tran
som
Tran
som
Tran
som
Tran
som
Mu
llion
Expan
sion
strip
104
April 2009
W50Curtain Wall system for facades and roofs
Thermal-insulated building construction Series W 50Cutting points
Cutting points, inclined glazing
Manufacturefrom PK 79
Spars of mullionsto meet static requirements
Purlin of transoms
Purlin of transoms
of PK 79,
50 m
m long
105
www.balkan.gr
W50Cutting point, frame insert, Series RG 75 block window for facade
Mullion
Axis
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Cutting points
106
April 2009
W50Cutting point, frame insert, Series RG 75 for facade
Door opening inwardsM
ulli
on
Axi
s
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Cutting points
107
www.balkan.gr
W50Cutting point, frame insert, Series RG 75 for facade
Door opening outwards
Mu
llion
Dri
lling
tem
plat
eA
xis
Pos
ition
ing
aid
for
6 m
m g
roov
e,tw
iste
d an
d no
t pin
ned
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Cutting points
108
April 2009
W50Cutting point, vertical facade, top
Design draftAttic cover
Cross section
VentilationAir inletin mullion area
VentilationDrainage
Transom
Sealing tapes
Mu
llion
Mullion
profileSliding
Air inletin the transom area
Tran
som
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Cutting points
109
www.balkan.gr
W50Cutting point, vertical facade, top
Design draft
Cross section
VentilationAir inletin mullion area
Sealing tapes
VentilationDrainageAir inletin the transom area
Transom
Mu
llion
Suspendedceiling
Bac
k-ve
ntila
ted
LM
cold
faca
de
Mullion
profileSliding
Tran
som
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Cutting points
110
April 2009
W50Cutting point, vertical facade, in front of a ceiling
Design draft
VentilationDrainage
Air inlet in the transom area
VentilationDrainage
Air inlet in the transom area
Finishedfloor level
Mu
llion
Transom
Suspendedceiling
Mu
llion
Transom
Sliding profile
Anchoring and- Quantity and- Distributionof the bolts:According tostatics
Mullion butt joint withreinforcement
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Cutting points
111
www.balkan.gr
W50Cutting point, vertical facade, lateral
Design draft
Slid
ing
prof
ile
Transom
Mu
llion
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Cutting points
112
April 2009
W50Cutting point, vertical facade, bottom
Design draft
Finishedfloor level
VentilationDrainage
Air inlet in the mullion area
VentilationDrainage
Air inlet in the mullion area
Horizontal cut
Vertical cut
Tran
som
Mullion
Sealing tape
Sliding Profile
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Cutting points
113
www.balkan.gr
W50
Design draft
Horizontal cut
Vertical cut
Cutting point, vertical facade, bottom
Finishedfloor level
VentilationDrainage
Air inlet in the mullion area
VentilationDrainage
Air inlet in the mullion area
Sealing tape
L profile
MullionTran
som
Curtain Wall system for facades and roofsThermal-insulated building construction Series W 50
Cutting points
BALKAN NETWORK
GREECE - BALKAN SA www.balkan.grHead Offi ce: Athens11th km Nat.Road Athens-Lamia, 144 52 MetamorphosiTel.: +30 210 2810 030, Fax: +30 210 2845 025e-mail: [email protected]
Iraklio: +30 2810 370555-6, Fax: +30 2810 311 400Larissa: +30 2410 555 641-2, Fax: +30 2410 288 919Τhessaloniki: +30 2310 753 454, Fax: +30 2310 753 455Τhiva: Tel.: +30 22620 72001-4, Fax: +30 22620 71293
Extrusion Industry79th km Nat. Road Athens-Lamia, Ipato ThivonTel.: +30 22620 72001-4, Fax: +30 22620 71293e-mail: [email protected]
ROMANIA - BALKAN RO www.balkanro.roHead Offi ce: BucharestB-dul Iuliu Maniu 333, Sector 6Tel.: +40 213 170 695-7-8, Fax: +40 213 160 699e-mail: [email protected]
Alba Iulia: +40 258 810 241, Arad: +40 257 288 588, Bacau: +40 234 562 620Βrasov: +40 286 549 904, Cluj-Napoca: +40 264 415 512, Constanta: +40 241 559 850Craiova: +40 251 483 323, Iasi: +40 232 244 055, Τimisoara: +40 256 296 114
DEALERSGalati: Alprovest, tel/fax: +40 236 458 038, Pitesti: Conarg, tel/fax: +40 248 610 089Satu Mare: Neptun, tel/fax: + 40 261 841 930, Sibiu: Roa Design, tel/fax: +40 269 214 325 Ploiesti: Rolir, tel/fax: +40 244 225 170
UKRAINE - BALKAN UA Head Offi ce: KievMoskovsky Av. 6Tel./Fax: +38 044 464 4947/7858
Κharkov: +380 57 757 5161-2Odessa: +380 482 328 402, 335 654, 0487 773 389
BULGARIA - BLK BG www.blk-bg.comΗead Offi ce: Sofi a8 Malashevska Str. 1202Tel.: +359 2 936 6652/91, Fax:+359 2 936 6735e-mail: offi [email protected]
CZECH REPUBLICALUMONT BUILDING A.S. DEALERHradni-Slazska 27/37, 710 00 OstravaTel./Fax: +420 777 800333e-mail: [email protected]
RUSSIAMGM LTD DEALERPromzona 16 Str.-Armavir, 352916 KrasnodarTel./Fax: +7 86137 58100e-mail: [email protected]
BELARUSSOL-FARM DEALERKalvariyskaya 60/2H, 220073 Minsk Tel./Fax: +37517 204 22 25e-mail: [email protected]