boysen paints
TRANSCRIPT
-
7/25/2019 Boysen Paints
1/15
BOYSEN PAINTS
TYPE DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSEN Clear Acrylic
Emulsion #700
Acrylic type transparent coating that acts as a
barrier against dampness on concrete walls.
Improves performance of latex paint
applied on humid and/or damp
environments.
20-25 square meter / 4 l iters / coat Thi rty (30) minutes Two (2) hours 1-1.5 mi ls /coat Al lowone hour before recoating.
Use as supplied. If
necessary, thin with not
more than 1/2 liter of water
per 4-liter can
paint brush, roller or airless
spray.
NewMasonry:
PREMIUM ACRYLIC WATER BASED PAINTS
: , ,
Allownewmasonry to dry 14 to 28 days under normal weather conditions before painting. Surfaces to be painted should be clean and dry, free fromoil, grease, dust, dirt contaminants, and all loose grit and mortar. Treat newmasonry with a solution of 1 part BOYSEN Masonry Neutralizer #44 diluted in 16 parts wroller. Let dry overnight before rinsing with water to remove white crystals that formon the surface. Let dry before painting.
SURFACE PREPARATION
PAINTING SCHEDULE
1st Coat: BOYSENPermacoatFlat Latex #701
2nd Coat: BOYSENClear Gloss Acrylic Emulsion #700
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSEN Masonry Putty
#7311
Water based product especially prepared for
filling minor surface unevenness while using
latex paint systems. Can also be used for full
puttying.
For interior concrete, stucco, bricks
plaster or any surface minor imperfection.
Full Putty - 10-12 square meter / 4 liters /
coat
Spot putty - 25 square meter / 4 liters /
coat
Thirty (30) minutes Two (2) hours Allow two hours before recoating Use as supplied. putty knife
1st Coat: BOYSENPermacoatFlat Latex #701
Putty: BOYSENMasonry Putty #7311
Topcoat: BOYSENPermacoatLatex (flat, semi-gloss, gloss)
Note: Interior use only. For exterior, use BOYSEN AcrytexCast #1711
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSEN Permacoat Latex
A100%acrylic latex paint with excellent hiding,
durability and dirt pick-up resistance. It finishes
painting jobs in less coats, yet lasts longer than
other brands allowing you to save a lot on time,
effort, worry and money.
For interior and exterior such as concrete,
stucco, bricks plaster, hollowblocks,
drywall surfaces, and properly primed
wood.
25-30 square meter / 4 l iters / coat Thi rty (30) minutes Two (2) hours 1-1.5 mi ls/coat Al lowone hour before recoating.
Use as supplied. If
necessary, thin with not
more than liter of water
per 4-liter can
paint brush, roller or airless
spray.
1st Coat: BOYSENPermacoatFlat Latex #701
PAINTING SCHEDULE
Topcoat: BOYSENPermacoatLatex (flat, semi-gloss, gloss)
PAINTING SCHEDULE
:
:
Putty:
BOYSEN Masonry Putty #7311 (interior use)
BOYSENAcrytex Cast#1711 (exterior use)
2nd &3rd Coat: BOYSENPermacoat Flat Latex (any desired color)
#3101 DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
-
7/25/2019 Boysen Paints
2/15
BOYSENPermatex #3101
Awater-based, full-bodied paint that dries to a
fine rubbery coating, creating a beautiful
textured finish on interior walls and ceilings
bringing elegance to your home interior. It
adheres easily on wood, masonry, and drywall
surfaces. Conceals hairline cracks and minor
surface imperfections, and dries to a fine
rubbery coating that does not become brittle,
leaving virtually no roomfor cracking, chipping,
or peeling off.
For interior wood, drywall, and masonry
surfaces.5 - 6 square meter / 4 liters Two (2) hours Overnight Two (2) hours
Use as supplied. If
necessary, thin with not
more than 1/2 liter of water
per 4 liter can
For a regular texture
pattern, apply
BOYSENPermatex
#3101 straight from the ca
using a regular textured
roller. If a different design
desired, first apply
BOYSENPermatex
#3101 with a regular
textured roller immediately
followed by the desired
Wood: Masonry & Drywall:
1st Coat: BOYSENFlatwall Enamel #800 1st Coat: BOYSENPermacoatFlat Latex #701
Putty: BOYSENPlasolux Glazing Putty #311 Putty: BOYSENMasonry Putty #7311
Texture: BOYSENPermatex#3101 Texture: BOYSENPermatex#3101
2nd &3rd coat: BOYSENPermacoatLatex (any desired color) 2nd &3rd coat: BOYSENPermacoatLatex (any desired color)
I I I I I I I I I I I I I
PAINTING SCHEDULE
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSEN Roofgard
a gloss acrylic, water-based roof paint designed
to protect and adhere to most roof substrates. It
gives a durable and flexible film, fast-drying time
and good gloss retention.
For galvanized iron surfaces, pre-painted
galvanized sheets, asphalt shingles, and
unglazed roof ti les. 25-30 square meter / 4 l iters / coat Thirty (30) minutes Two (2) hours 1.5 mils/coat Two (2) hours
Maximum1/2 liter water per
4 liters paint
by brush, roller or spray.
Clean equipment with soap
and water after use
For unpainted galvanized iron sheets, etch the surface by applying 10%BOYSENMetal Etching Solution #71 (dilute 1 part of B-71 to 9 parts water). Wipe the surface with rag soaked in BOYSEN Paint Thinner #0340 to remove grease. Rinse with water and let dry.
For prepainted galvanized iron sheets, scuff sand surface using sandpaper and wipe the surface with clean rag before applying paint. Spot prime if necessary.
For corroded G.I. surface, remove rust by wire brushing and use BOYSEN Metal Etching Solution #71. Let it stay for 10-15 minutes. Be sure to wash off surface thoroughly with water or paint thinner and let dry. Apply primer a few hours after application of B-71 and before rust sets in.
For newunglazed roofti les, make sure surfaces are completely clean and dry.
Primer for: Topcoat:
Galvanized Iron Sheets BOYSENRoofgard (2-3 coats; any desired color)
BOYSENRed Oxide #310, BOYSENRust OffPrimer Gray #330, Repainting:
or BOYSENPrimeguard#4310 For G.I. sheets with paint in good condition, clean surface of dirt and dust by washing and apply two coats of BOYSEN Roofgard.
Unglazed tiles:
BOYSENAcrytexPrimer #1705
I I I I I I I I I I I I I
SPECIALTY WATER BASED COATINGS
SURFACE PREPARATION
PAINTING SCHEDULE
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSEN EcoPRIMER
#105
An eco-friendly acrylic water-based primer used
for masonry and drywall surfaces. This ultra-low
volatile organic compound (VOC) formulation is
designed to have superior alkali resistance,
excellent adhesion and sealing properties ideal
for interior and exterior application.
25-30 square meter / 4 l iters / coat. Thirty (30) minutes. Two (2) hours. 1-1.5 mils/coat. Allowone hour before recoating. Use as supplied.paint brush,roller orairle
spray.
NewMasonry:
SURFACE PREPARATION
-
7/25/2019 Boysen Paints
3/15
Repainting:
1st Coat: BOYSENEcoPRIMER#105
Putty: BOYSENAcrytexCast #1711 (for exterior);
BOYSENMasonry Putty #7311 (for interior)
2nd &3rd Coat: BOYSENHealthy Home(for interi or)
VirtuosoSilk Touch(for interior)
BOYSENKNOxOUTAir Cleaning Paint #8701 Acrylic Water-based
BOYSENKNOxOUTAir Cleaning Paint #8702 Silicon-based
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
Odor-less, lowVOC, remiumacr lic, water-
. ,
.
Is the ideal choice for residences,
, ,
, ,
.
.
. . . ,
Allownewmasonry to dry for 14 to 28 days under normal weather conditions before painting. Surface to be painted should be clean and dry, free fromoil, grease, dust, dirt, contaminants, and all loose grit and mortar. Treat newmasonry with a solution of 1 part BOYSEN Masonry Neutralizer #44 diluted in 16 parts
roller. Let dry overnight before rinsing with water to remove white crystals that form on the surface. Let dry before painting.
Remove all loose, scaling, flaking and peeling off paint using BOYSENPaint and Varnish Remover #141, wire brushing, scraping, or water blasting. Let it dry. Sand smooth painted surfaces for improved adhesion. Apply 1 coat of BOYSEN Chalk Blockerfor chalking old paint. In case of mildewi nfestation, treat w
bleach solution (1:3, laundry bleach to water, respectively) by swabbing or brushing. To ensure proper treatment, allow to stand on surface for overnight before washing off residue. Let dry.
PAINTING SCHEDULE
I
BOYSEN Healthy Home
Odor-less Antibacterial Latex
Paint
- , , , -
based interior coating with exclusive Microban
antibacterial protection to give extra defense
against bacteria such as E. coli and Salmonella,
as well as mildewand fungus.
I ,
medical facilities, nursing homes,
schools, day care facilities, and food
commissaries. For inter ior concrete and
drywall surfaces.
25-30 square meter / 4 l iters / coat Thirty (30) minutes Two (2) hours 1-1.5 mils/coat Allowone hour before recoating. Use as supplied.paint brush, roller or airless
spray
NewMasonry:
Repainting:
Concrete Drywall Surfaces
1st Coat: BOYSENPermacoatFlat Latex #701 1st Coat: BOYSENPermacoatFl at Latex #701
Putty: BOYSENMasonry Putty #7311 Putty: BOYSEN GypsumJoint Compound #711
2nd & 3rd Coat: BOYSENHealthy Home 2nd &3rd Coat: BOYSENHealthy Home
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
Is a 100%acrylic water-based paint that is low
odor, lowVOC, lead free, and has outstanding
. I
.
,
,
.
.
.
. . . ,
.
Allownewmasonry to dry 14 to 28 days under normal weather conditions before painting. Surfaces to be painted should be clean and dry, free fromoil, grease, dust, dirt contaminants, and all loose grit and mortar. Treat newmasonry with a solution of 1 part BOYSEN Masonry Neutralizer #44 diluted in 16 parts w
roller. Let dry overnight before rinsing with water to remove white crystals that formon the surface. Let dry before painting.
Remove all loose, scaling, flaking and peeling off paint using BOYSENPaint and Varnish Remover #141, wire brushing, scraping, or water blast ing. Let dry. For chalking old paint, use BOYSEN Chalk Blocker #7304 as primer. In case of mildew infestation, treat with fungicidal wash solution or bleach solution (1:3
respectively) by swabbing or brushing. To ensure proper treatment, allow to stand on surface for overnight before washing off residue. Let dry.
PAINTING SCHEDULE
I
SURFACE PREPARATION
Virtuoso Silk Touch
I
, , ,
color retention. It dries to a luxurious silk finish
that not only imparts a sense of warmth and
depth to your living space but is also distinctively
smooth to touch. With Teflonsurface
protector, oil and dirt cannot easily stick to your
walls, making it easy to wipe off common
everyday stains.
Best for areas in need of stain resistant
walls. For interior concrete and drywall
substrates.
25-30 square meter / 4 l iters / coat Thirty (30) minutes Two (2) hours 1-1.5 mils/coat Allowone hour before recoating. Use as supplied.paint brush, roller or airless
spray.
Please refer to CHOOSEYOUR PAINTsection for specifics.
SURFACE PREPARATION
PAINTING SCHEDULE
-
7/25/2019 Boysen Paints
4/15
Concrete Drywall Surfaces
1st Coat: BOYSEN PermacoatFlat Latex #701 1st Coat: BOYSENPermacoatFlat Latex #701
Putty: BOYSENMasonry Putty #7311 Putty: BOYSENGypsumJoint Compound #711
2nd & 3rd Coat: VirtuosoSilk Touch 2nd & 3rd Coat: VirtuosoSilk Touch
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSEN Alkyd Traffic Paint
An alkyd-based paint for traffic markings/linings.
It must be applied on epoxy-primed asphalt and
rough concrete.
It is designed for use on street markings,
curbs, traffic lanes and safety zone lining.20-25 sq. m/ gal / coat 30 minutes 1 hour 1 hour 1 hour
BOYSENPaint Thinner
#0340 if neededBy brush, roller
1st coat: BOYSENEpoxy Primer White #2200
2nd and 3rd coat: BOYSENAlkyd Traffic Paint
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
. I
. I
.
. .
ALKYD ENAMEL / OIL BASED PAINTS
PAINTING SCHEDULE
I
BOYSEN Flatwall Enamel
#800
a a y ype pain a provi es grea
durability while being noted as a fast drying
paint. It is formulated to give a tough and
durable film. It is also used as a primer for
enamel coatings.
For interior and exterior wood surfaces. 20 - 25 square meter / 4 li ters / coat Thirty (30) minutes Eight (8) hours 1.5 mils/coat Allowsix (6) hours before recoatUse BOYSENPaint
Thinner #0340By brush or roller
Surface to be painted should be clean and dry, free fromdust, dirt and other foreign matter. Hammer all nails deep enough to apply putty. Sand rough wood until smooth, then dust off before paint ing.
If repainting, first remove all blistering, peeling and scaling paint by wire brushing or BOYSEN Paint and Varnish Remover #141. Clean surfaces thoroughly before painting.
1st Coat: BOYSENFlatwall Enamel #800
Putty: BOYSENPlasolux Glazing Putty #311
2nd &3rd Coat: BOYSENFlatwall Enamel #800
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSEN Heat Resistin g
Alumin um #95
Formulated for surfaces subject to heat with
peak temperature of 800 F or 427 C.
For metal surfaces of equipment,
radiators and machinery.20 square meter / 4 liters / coat
Will dry when peak
temperature is reached.1.5-2 mils Allow overnight before recoating not necessary by brush
Metal:
Wipe the surface with rag soaked in lacquer thinner to remove dust, dirt, grease, oil, wax and other foreign matter.
For rusted portions, wire brush or scrape loose rust and apply BOYSEN Metal Etching Solution #71. Let it stay for 10-15 minutes. Be sure to wash off surface thoroughly with water or paint thinner, letting it dry before applying paint. Product should be applied immediately after treatment to prevent flash rusting.
I I
SURFACE PREPARATION
PAINTING SCHEDULE
SURFACE PREPARATION
Apply 2 to 3 coats of BOYSENHeat Resisting Aluminum#95 on bare substrate.
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSEN Plasolux Glazing
Putty #311
An alkyd-type product specially prepared for
filling minor surface unevenness on enamel-
painted wood.
For filling minor surface dents and
imperfections on wood.
Full Putty - 10-12 square meter / 4 liters /
coat
Spot putty - 25 square meter / 4 liters /
coat
4-5 hours Overnight Allowtwo hours before recoatingBOYSENPaint Thinner
#0340 if necessaryput ty knife
1st Coat: BOYSENFlatwall Enamel White #800
, . . , . .
PAINTING SCHEDULE
PAINTING SCHEDULE
-
7/25/2019 Boysen Paints
5/15
Putty: BOYSENPlasolux Glazing Putty #311
2nd &3rd coat: BOYSENQuick Drying Enamel (any desired color),
BOYSENSemi-Gloss Enamel #200, or BOYSENFlatwall Enamel White #800
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSEN Quick Drying
Enamel
An alkyd type paint that provides great durability
while being noted as a fast drying paint. It is
formulated to give a tough, durable, beautiful
and high build film on wood and metal. Its
superior hiding, combined with an exceptionally
high gloss level, leads to an excellent, long-
lasting finished appearance.
Superior for exterior and interior wood
and metal surfaces.20 - 25 square meter /4 li ters /coat Five (5) hours maximum Two (2) hours 1.5 mi ls/coat Al loweight (8) hours
Use BOYSENPaint
Thinner #0340 if necessaryBy brush or roller
Wood - Surface to be painted should be clean and dry, free fromdust, dirt and other foreign matter. Hammer all nails deep enough to apply putty. Sand rough wood until smooth, then dust off before painting.
If repainting, first remove all blistering, peeling and scaling paint by wire brushing or BOYSEN Paint and Varnish Remover #141. Clean thoroughly prior to painting.
Metal - Wipe the surface with rag soaked in paint thinner to remove dust, dirt , grease, oil, wax and other foreign matter. For newG.I. sheets, etch the surface by applying 10%BOYSEN Metal Etching Solution #71 (dilute 1 part of B-71 to 9 parts water).
SURFACE PREPARATION
, , , , . .I. , .
If repainting, wire brush or scrape rusted metals and apply BOYSEN Metal Etching Solution #71 to remove all rust. Let it stay for 10-15 minutes. Be sure to wash off surface thoroughly with water, lett ing it dry before applying paint. Prime immediately after drying.
WOOD METAL
1st Coat: BOYSEN Flatwall Enamel #800 1st coat: BOYSENRed Oxide Primer #310,
Putty: BOYSEN Plasolux Glazing Putty #311 BOYSEN Rust OffPrimer Gray #330, or BOYSENPrimeguard#4310
2nd &3rd Coat: BOYSENQuick Dry Enamel (any desi red color) 2nd &3rd Coat: BOYSEN Quick Dry Enamel (any desired color)
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSENRed Oxide Primer#310
Arust inhibiting primer for steel and iron
surfaces. It is particularly good for metal shops
who deliver metal products coated with a shop
primer to protect themfromrust corrosion until
such time as they are finished with desiredtopcoat.
As a primer for exterior and interior steel. 25 - 30 square meter /4 liters /coat Two hours 1.5 mils/coat 8 hours to overnightUse BOYSENPaint
Thinner #0340 if necessary
By brush, roller or
conventional spray
Wipe the metal surface with rag soaked in paint thinner to remove dust, dirt, grease, oil, wax and other foreign matter. For new G.I. sheets, etch the surface by applying 10%BOYSEN Metal Etching Solution #71 (dilute 1 part of B-71 to 9 parts water).
If repainting, wire brush or scrape rusted metals and apply BOYSENMetal Etching Solution #71 to remove all rust. Let it stay for 10-15 minutes. Be sure to wash off surface thoroughly with water, letting it dry before applying paint. Prime immediately after drying.
1st Coat: BOYSENMetal Primer Red Oxide #310
2nd &3rd Coat: BOYSENQuick Dry Enamel (any desired color)
I I I I I I I I I I I I I
SURFACE PREPARATION
PAINTING SCHEDULE
PAINTING SCHEDULE
I I I I I I I I I I I I I
BOYSEN Reflectorized
Traffic Paint
An alkyd-type paint specially developed to resist
the rigorous environment encountered on
highways, roads, pavements, and parking lots. It
forms a durable filmthat offers good wear
resistance and better reflective beads retention
for safety markings.
Areflectorized variant to the alkyd-based
traffic paint for use on road markings and
pavement linings. To be used only on
areas in direct contact to wheel traffic
otherwise the reflectorized-effect will not
manifest.
20 square meter / 4 liters / coat 10 minutes 30 minutes 30 minutesBOYSENPaint Thinner
#0340 if necessaryBy brush
1st coat: BOYSEN
Epoxy Primer White #22002nd coat &3rd coat: BOYSENReflectorized Traffic Paint (of desired color)
PAINTING SCHEDULE
-
7/25/2019 Boysen Paints
6/15
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSEN Schoolboard
Slating Paint, Green #655
An alkyd based paint that dries to a flat finish for
classroomblackboards, bulletin boards and
similar flat surfaces intended for chalk markings.
For metal or wood surfaces. 25-30 square meter / 4-liter / coat 2-4 hours Overnight 1.5 mils/coat Allow overnight before recoatingBOYSENPaint Thinner
#0340by brush or roller
Newwood:
Surface to be painted should be clean and dry, free fromdust, dirt and other foreign matter. Hammer all nails deep enough to apply putty. Sand rough wood until smooth, them dust off before painting.
Repainting:
For previously painted surfaces, scrape off loosely adhering paint. Remove oil and grease by detergent cleaning. Scuff sand for improved anchorage of succeeding coats.
1st Coat: BOYSENFlatwall Enamel #800
Putty: BOYSEN Plasolux Glazing Putty #311
Topcoat: BOYSENSchoolboard Slating Paint #655
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
SURFACE PREPARATION
PAINTING SCHEDULE
I I I I I I I I I I I I I
BOYSEN Semi-Gloss
Enamel #200
An alkyd type paint that provides great durability
while being noted as a fast drying paint. It is
formulated to give a tough and durable filmon
wood and metal. Its superior hiding and sheen
makes it easier to clean and resist wear and
abrasion.
For interior and exterior wood and metal
surfaces.20 - 25 square meter / 4 li ters / coat Thi rty (30) minutes Ten (10) hours 1.5 mi ls/coat Al lowsix (6) hours before recoat
Use BOYSENPaint
Thinner #0340 if necessaryBy brush or roller
Wood - Surface to be painted should be clean and dry, free fromdust, dirt and other foreign matter. Hammer all nails deep enough to apply putty. Sand rough wood until smooth, then dust off before painting.
If repainting, first remove all blistering, peeling and scaling paint by wire brushing or BOYSEN Paint and Varnish Remover #141. Clean thoroughly prior to painting.
Metal - Wipe the surface with rag soaked in paint thinner to remove dust, dirt , grease, oil, wax and other foreign matter. For newG.I. sheets, etch the surface by applying 10%BOYSEN Metal Etching Solution #71 (dilute 1 part of B-71 to 9 parts water).
If repainting, wire brush or scrape rusted metals and apply BOYSENMetal Etching Solution #71 to remove all rust. Let it stay for 10-15 minutes. Be sure to wash off surface thoroughly with water, letting it dry before applying paint. Primer should be applied immediately after treatment.
Wood Metal
1st coat: BOYSENFlatwall Enamel #800 1st coat: BOYSENRed Oxide Primer #310,
Putty: BOYSENPlasolux Glazing Putty #311 BOYSENRust OffPri mer Gray #330, or BOYSENPrimeguard#4310
2nd &3rd coat: BOYSENSemi-Gloss Enamel #200 2nd &3rd coat: BOYSENSemi-Gloss Enamel #200
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSEN Silver Finish
Alumin um Paint #75
Aready mixed aluminumpaint for general use
on industrial and decorative work, for maximum
wear.
For exterior and interior metal. 25-30 sq.m / gallon 2 -4 hours Overnight 1.5 mils/coat Allow overnight before recoating not necessary by brush
SURFACE PREPARATION
PAINTING SCHEDULE
I I
1st coat: BOYSENRed Oxide Primer #310, BOYSENRust OffPrimer Gray #330, or BOYSENPrimeguard#4310
2nd &3rd Coat: BOYSENSilver Finish AluminumPaint #75
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSENSpar Varnis h #58
Aclear, alkyd-type, glossy varnish that dries to a
hard durable film without obliterating the natural
appearance of wood.
Enhances wood grain of furniture,
fixtures, cabinets, doors, doorjambs and
panels.
25-30 sq.m/ gallon 4-6 hours 12 hours 1.5 mils/coat Recoat after 12 hoursBOYSENPaint Thinner
#0340by brush or spray
Newwood surfaces:
I I
PAINTING SCHEDULE
-
7/25/2019 Boysen Paints
7/15
Stain: BOYSENOil Wood Stain (optional)
Final coat: BOYSENSpar Varnish #58. Recoat for a clear gloss finish.
Repainting:
Loose film should be stripped. BOYSENPaint and Varnish Remover #141 can be used to totally remove the existing finish.
If old lacquer finish is in good condition, sand surface. Make sure to clean and dry before coating with BOYSEN Spar Varnish #58.
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSEN Oil Wood Stain
Available in various shades to bring out a clear
and natural tone in wood. When clear coatedwith BOYSENLacquer varnish products,
BOYSENOil Wood Stain highlights wood
grains, adds freshness and color, and provides
superior protection.
For enhancing wood grain on interior
wood works and other surfaces such as
cabinets, furniture, paneling, etc.
25 - 30 square meter /4 liters /coat
(depending on wood absorptivity)Two (2) hours 4-5 hours 1.5 mils / coat Overnight
BOYSENPaint Thinner
#0340by brush or spray
OIL WOOD STAINS
SURFACE PREPARATION
Sand surface until wood is smooth to the touch and no slivers or rough edges remain. Hammer all nails deep enough to apply putty. Dust off surfaces completely then wipe with a clean rag.
If repainting, remove all paint by wire brushing, scraping, or by using BOYSEN Paint &Varnish Remover #141.
NewWood:
1st coat: BOYSENOil Wood Stain (any desired color)
2nd coat and 3rd coats: BOYSENLacquer Sanding Sealer #1254
4th and 5th coats: BOYSENClear Gloss Lacquer #1250
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSENXyladecor
Asolvent based, deep penetrating type of stainthat combines decorative, water repellent and
wood preserving properties in one and dries to a
silk matte finish. It emphasizes the grain,
bringing out the natural beauty in any kind of
wood.
Is the wood stain available that could beused for exterior and interior wood
surfaces. It is the best way to protect
your wood since it seals, prevents fungal
growth, mold and insect attacks through
its preservative contents.
20 - 25 square meter /4 liters /coat (may
vary depending on wood absorptivity)Thirty (30) minutes Overnight
30 minutes, depending on weather
and absorption rateNot necessary
by brush, spray or by
dipping
Sand surface until wood is smooth to the touch and no slivers or rough edges remain. Hammer all nails deep enough to apply putty. Dust off surfaces completely then wipe with a clean rag.
If repainting, remove all paint by wire brushing, scraping, or by using BOYSEN Paint &Varnish Remover #141.
I
PAINTING SCHEDULE
Thoroughly stir the can contents before using. Apply BOYSEN Oil Wood Stain direct to bare wood without primers or undercoats either by brush, spray or by dipping in an open trough or tank. Lightly brush or wipe over once along the grain to remove excess material and to smooth out any runs. Leave each coat for
totally dry. Recoat for a darker shade.
SURFACE PREPARATION
PAINTING SCHEDULE
Thoroughly shake the can before opening. Apply BOYSENXyladecordirect to base wood without primers or undercoats either by brush, spray or by dipping in an open trough or tank to achieve total covering rate. Shake and stir Xyladecor often during use.
By Spray: Use a coarse nozzle (about 1-5 mm) giving a steamof material rather than a fine atomizing type paint spray. Working pressure should be approximately 44 lbs. / m2. Spraying is not recommended for planed surfaces.
By dipping: Dip the timber in BOYSENXyladecorfor 2 minutes, varying the time required according to the absorbency of the wood. Stand the timber on end and allowto drain. If necessary, li ghtly brush the surface once in the direction of the grain before it dries.
Note: If a very even color finish is desired on wood with varying degrees of absorbency, apply BOYSEN XyladecorColorless fi rst before applying colored varieties of Xyladecor. BOYSENXyladecorColorless is not recommended for exterior use on its own.
NITROCELLULOSE LACQUER BASED COATINGS
By Brush: Apply at least 3 full brush coats, laying the paint into the wood rather than brushing out. Leave each coat for about thirty (30) minutes, depending on the weather and the absorption rate. Lightly brush or wipe over once along the grain to remove excess material and to smooth out any runs.
I I
-
7/25/2019 Boysen Paints
8/15
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSEN Automotive
Lacquer #1300
Anitrocellulose, solvent-based, high gloss,
lacquer type paint that is easy to apply and dries
rapidly to a long-wearing attractive finish.
For indoor wood surfaces such as doors,
doorjambs, cabinets, and shelves.25-30 square meter / 4 liters / coat 10 minutes 30 minutes 1.5 mils / coat 1 hour
BOYSENLacquer Thinner
#50by spray or brush
Please refer to CHOOSEYOUR PAINTsection for specifics.
Newwood surfaces:
1st coat: BOYSENLacquer Primer Surfacer #305
Putty: BOYSENLacquer Spot Putty #306 if required
2nd coat: BOYSEN
Lacquer Primer Surfacer #305 on puttied areas
Final coat: BOYSENAutomotive Lacquer #1300 in required number of coats
(Note: 10%by volume of BOYSENLacquer Flo is mixed with the topcoat just before application to prevent moisture blushing)
I I I I I I I I I I I I I
SURFACE PREPARATION
PAINTING SCHEDULE
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSENClear Dead Flat
Lacquer #1253
Is a nitrocellulose, solvent-based, flat lacquer
varnish finish that dries to a hard durable film. Its
high build properties make it superior for
furniture, fixtures, and other woodworks.
For interior sealed wood such as
furniture, store fixtures, cabinets, doors
and panels.
25-30 square meter / 4 liters / coat 10 minutes 1 hour 1.5 mils / coat Recoat after 30 minutesBOYSENLacquer Thinner
#50by spray or brush
Newwood surfaces: Repainting:
Sealer coat: BOYSENLacquer Sanding Sealer #1254 Old finish in bad condition should be stripped. BOYSENPaint and Varnish Remover #141 can be used to totally remove the finish.
Final coat: BOYSENClear Dead Flat Lacquer #1253 If old lacquer finish is in good condition, sand surface. Make sure to clean and dry before coating the required coats of BOYSEN Clear Dead Flat Lacq
(Note: 10%by volume of BOYSENLacquer Flo is added to the varnish mixture just before application to prevent moisture blushing)
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSEN Clear Gloss
Lacquer #1250
Anitrocellulose, solvent-based, high gloss
lacquer varnish finish that dries to a hard durable
film.
For interior sealed wood such as
furnitures, fixtures, cabinets, doors and
panels.
25-30 square meter / 4 liters / coat 10 minutes 1 hour 1.5 mils / coat Recoat after 30 minutesBOYSENLacquer Thinner
#50by brush or spray
Newwood surfaces: Repainting:
Stain (optional): Boysen Oil Wood Stain Old finish in bad condition should be stripped. BOYSENPaint and Varnish Remover #141 can be used to totally remove the finish.
Sealer Coat: BOYSENLacquer Sanding Sealer #1254, sanded lightly before topcoat application If old lacquer finish is in good condition, sand surface. Make sure to clean and dry before coating BOYSEN Clear Gloss Lacquer #1250.
:
PAINTING SCHEDULE
PAINTING SCHEDULE
Final coat: BOYSENClear Gloss Lacquer #1250
(Note: 10%by volume of BOYSENLacquer Flo is added to the varnish mixture just before application to prevent moisture blushing)
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSEN Lacquer Primer
Surfacer #305
Anitrocellulose lacquer type sealer with
excellent holdout properties that provide
good foundation for the desired lacquer topcoat.
As primer for indoor wood surfaces 25-30 square meter / 4 liters / coat Ten minutes Thirty minutes 1.5 mils/coatAllowthirty minutes before
recoating
BOYSENLacquer Thinner
#50by brush or spray
Newwood surfaces: Repainting:
PAINTING SCHEDULE
-
7/25/2019 Boysen Paints
9/15
1st coat: BOYSENLacquer Primer Surfacer #305 Old finish in bad condition should be stripped. BOYSENPaint and Varnish Remover #141 can be used to totally remove the finish. Follow procedure o
2nd coat: BOYSENLacquer Spot Putty #306 If old lacquer finish is in good condition, sand surface.
3rd coat: BOYSENLacquer Primer Surfacer #305
Final coat: BOYSENAutomotive Lacquer #1300 or BOYSENGloss Lacquer Enamel #1200 in required coats
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSEN Lacquer Sanding
Sealer #1254
Acommercial grade nitrocellulose-based sealer
for wood before finishing with either gloss or flat
lacquer. It has good sealing and hold out
properties, and require less sanding.
For interior sealed wood such as
furniture, fixtures, cabinets, doors and
panels.
25-30 square meter / 4 liters / coat 10 minutes 1 hour 1.5 mils / coat Recoat after 30 minutesBOYSENLacquer Thinner
#50by brush or spray
Newwood surfaces: Repainting:
Sealer coat: BOYSENLacquer Sanding Sealer #1254 Old finish in bad condition should be stripped. BOYSENPaint and Varnish Remover #141 can be used to totally remove the finish.
Final coat: BOYSENClear Gloss Lacquer #1250 or BOYSENClear Dead Flat Lacquer #1253 If old lacquer finish is in good condition, sand surface. Make sure to clean and dry before coating.
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
PAINTING SCHEDULE
I I I I I I I I I I I I I
BOYSEN Lacquer Spot
Putty #306
Ahigh quality, nitrocellulose-based, lacquer type
putty for wood specially formulated for easy
application and sanding.
For interior wood surfacesSpot putty - 25 square meter / 4 liters
Full putty - 12 square meter / 4 liters5-10 minutes One (1) hour Recoat after 30 minutes
Apply as is. If necessary,
use BOYSENLacquer
Thinner #50
Put ty knife
Newwood surfaces: Repainting:
1st coat: BOYSENLacquer Primer Surfacer #305 Old finish in bad condition should be stripped. BOYSENPaint and Varnish Remover #141 can be used to totally remove the finish.
2nd coat: BOYSENLacquer Spot Putty #306 If old lacquer finish is in good condition, sand surface. Make sure to clean and dry before coating with BOYSEN Automotive Lacquer #1300.
3rd coat: BOYSENLacquer Primer Surfacer #305
Final coat: BOYSENAutomotive Lacquer #1300 in required coats
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSENWater White Clear
Gloss Lacquer #1258
Is the highest grade clear gloss lacquer finish for
a durable finishing for interior woodwork. Its
properties enhance the natural grain of wood.
For lacquer finishing of interior wood
walls, furniture, fixtures, cabinets, doors
and panels.
25-30 sq.m/ gallon / coat 10 minutes 1 hour 1.5 mils / coat Recoat after 30 minutes BOYSENLacquer Thinner#50
by brush or spray
Sealer coat: BOYSENLacquer Sanding Sealer #1254 Repainting:
Final coat: BOYSENWater White Clear Gloss Lacquer #1258 Old lacquer finish in bad condition should be stripped. Prepare to clean and dry before finishing as indicated for new wood.
If old lacquer finish is in good condition, sand and dust surface. Make sure to clean and dry before coating. Apply required finish coats of BOYSEN Water White Clear Gloss Lacq
(Note: 10%by volume of BOYSENLacquer Flo is added to the varnish mixture just before application to prevent moisture blushing)
PAINTING SCHEDULE
PAINTING SCHEDULE
:
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSEN Acrytex
An acrylic solvent-based coating that forms a
seamless, non-porous, watertight film that repels
water and prevents seepage. It is noted for its
excellent adhesion and long-termdurabili ty.
Creates a very tight film, serving as a moisturesealant for concrete and a stain inhibitor for
wood.
For newand previously Acrytex-Painted
exterior and interior masonry, wood and
properly primed steel.
textured finish -- 15 -18 square meter / 4
liters / coat plain finish -- 25-30
square meter / 4liters / coat
Thirty (30) minutes Two (2) hours 1.5 mils/coat Two (2) hoursBOYSENAcrytex
Reducer #1750
SOLVENT-BASED ACRYLIC PAINTS
-
7/25/2019 Boysen Paints
10/15
Please refer to CHOOSEYOUR PAINTsection for specifics.
Plain Finish:
1. Prime surface with BOYSENAcrytexPrimer #1705.
2. Fill hairline cracks and minor surface imperfections with BOYSEN AcrytexCast #1711 using a putty knife.
3. Spot prime puttied portions with BOYSENAcrytexPrimer #1705.
4. Apply 2-3 coats of BOYSENAcrytexTopcoat of desired sheen by brush, roller or spray.
Textured Finish:
1. Prime surface with BOYSENAcrytexPrimer #1705.
2. Spray BOYSENAcrytexCast #1711 with mortar gun. Press Acrytex Cast with wooden roller 10-15 minutes after spraying. (Note: wet wooden roller with BOYSEN Acrytex Reducer #1750 to prevent the roller from sticki ng to the cast).
3. Apply 2-3 coats of BOYSENAcrytexTopcoat of desired sheen by brush, roller or spray.
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
An acrylic solvent-based putty for correction of
.
. I
.
.
,
. I
. ,
.
. .
. .
SURFACE PREPARATION
PAINTING SCHEDULE
I
BOYSEN Acry tex Cast
#1711
minor surface imperfections when a plain finish
of BOYSENAcrytex Topcoat is desired.
Gives an elegant and durable textured finish
when applied with a mortar gun. It is water tight
thus can repel water and prevent seepage.
Noted for excellent adhesion and long term
durability.
For newand previously painted exterior
and interior masonry, wood and fiber
cement boards. It also acts as a water
repellent. Creates a very tight film,
serving as a moisture sealant for
concrete and a stain inhibitor for wood.
As putty -- 10-12 sq.m./gal/coat
As texture -- 5-6 sq.m./gal/coatThirty (30) minutes Two (2) hours Four (4) hours
Use BOYSEN Acrytex
Reducer #1750 only
by mortar gun (texture) or
putty knife (putty)
Repainting
For surfaces previously painted with latex, enamel or lacquer coatings, scrape to bare substrate and clean surface thoroughly, then followschedule for newpainting.
Plain Finish:
1. Prime bare substrate with BOYSENAcrytex Primer #1705.
2. Putty minor surface imperfections with BOYSENAcrytexCast #1711. Spot prime puttied areas.
3. Brush on BOYSEN AcrytexPri mer #1705 when a high gloss finish on wood is desired.
4. Finish with two (2) coats of BOYSENAcrytex Topcoat to desired sheen.
Textured Finish:
1. Prime bare substrate with BOYSENAcrytexPrimer # 1705.
2. Spray BOYSEN AcrytexCast # 1711 with mortar gun. Press Acrytex Cast with plain wooden roller 10-15 minutes after spraying. Wet wooden roller with water to prevent the roller from sticking to the cast.
3. Finish with two (2) coats of BOYSENAcrytexTopcoat to desired sheen.
PAINTING SCHEDULE
SURFACE PREPARATION
Allownewmasonry to dry for 14 to 28 days under normal weather conditions before painting. No need to treat newmasonry with BOYSEN Masonry Neutralizer #44. Surface to be painted should be clean and dry, free fromoi l, grease, dust, dirt , contaminants, and all loose grit and mortar.
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSEN Acry tex Clear
Coat #1700
An acrylic solvent-based coating that has
excellent adhesion, long termdurabilit y and easy
clean- up characteristics, creating a superior
sheen and maximumprotect ion
As a clear coat protection for masonry
and wood surfaces.25 - 30 sq.m. / coat / gal. Thirty (30) minutes Two (2) hours 1.5 mils / coat Two (2) hours
Use BOYSEN
AcrytexTMReducer #1750
only
By brush, roller or spray
Apply 2 to 3 coats of BOYSENAcrytexTMClear #1700 on bare pebble washout or natural stone finished walls by air spray or brush.
For walls with BOYSENMultif leckTM, apply a thin coat by spray if gloss finish is desired.
PAINTING SCHEDULE
-
7/25/2019 Boysen Paints
11/15
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSEN Acqua Epoxy
Atwo-component water based acrylic epoxy
paint that has superior solvent, chemical and
stain resistance ideal for concrete floors and
properly primed metal surfaces. It has the
advantage of easier application and better
weather resistance properties.
For floorings, walls, metal substrates and
other well primed surfaces.25-30 square meter / 4 li ters /coat Thi rty (30) minutes Four (4) hours 1.5 mi ls/coat
Allowfour (4) hours before
recoating. For best results,
recoating should be done
overnight.
Not recommendedpaint brush, roller or airless
spray gun
MIXING RATIO: 4:1, paint to catalyst, respectively
Concrete Flooring:
Finished acid etched surface should have a texture similar to that of 40-60 grit sandpaper. Make sure that the surfaces to be painted are clean and dry.
: .
TWO-COMPONENT EPOXY BASED COATINGS
SURFACE PREPARATION
Remove oil and grease by detergent cleaning. For smooth surfaces, acid etch to improve adhesion. Do this by mixing one (1) part muriatic acid to one (1) part water. Apply over masonry and let stand for 2-3 minutes. Rinse with water to remove residual acid. If possible, rinse by pressure washing.
Caution: Adequate protection and ventilation should be provided when working with acids.
Metal:
Concrete Flooring:
Mix three (3) parts of BOYSENEpoxy Primer White #2200 to one (1) part of its catalyst.
Allowtwenty (20) minutes induction time. Thin 1:1 with BOYSENEpoxy Reducer #55. Apply as primer coating on bare concrete. Let dry overnight.
Metal:
NOTE:
Foot traffic abrasion resistance fully develops after three (3) days of curing. For heavy-duty application, allow seven (7) days of drying.
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
Ahigh quality, two-component, epoxy-polyamide
systemthat has excellent corrosion resistance
and sealing properties. Highly alkali-resistant so
there is no need for neutralization of new
.
As a topcoat for BOYSENEpoxy Primer
that can be applied on interior surfaces
such as metal, galvanized iron, wood and
.
20-30 square meter / 4 liters / coat 2-3 hours 6-8 hours 1.5 mils/coatBOYSENEpoxy Reducer
#55By paint brush or spray gu
Be sure to wash off surface thoroughly with water. Wipe off surface with rag soaked in paint thinner to remove dust, dirt, grease, oil, wax and other foreign matter. For newG.I. sheets, etch the surface by applying 10%BOYSEN Metal Etching Solution #71 (dilute 1 part of B-71 to 9 parts water).
If repainting on surfaces with alkyd, latex or lacquer-based coatings, scrape off all paint f ilm to bare substrate. Remove oil and grease by detergent cleaning followed by scuff sanding. To remove rust, wire brush or scrape affected areas and apply BOYSEN Metal Etching Solution #71 over rusted portions. Let it stay
off surface thoroughly with water, letting it dry before applying paint. Primer should be applied immediately upon drying of the surface before rust sets in.
PAINTING SCHEDULE
Mix four (4) parts of BOYSENAcqua Epoxy to one (1) part of its catalyst. Allowtwenty (20) minutes induction time. Mixture may gel if not used within 24 hours. Apply three (3) coats as topcoat, all owing for at least 4 hours between coats. For best results, recoating should be done overnight.
Prime bare metal with BOYSENEpoxy Red Oxide Primer #2277 or BOYSENEpoxy Primer Gray #2230. Let dry eight (8) hours before recoating. Alternatively, BOYSEN Primeguard#4310 can be used. Apply a single coat and let dry for 2-4 hours before recoating. Finish with 2-3 coats of BOYSENAcqua Epo
before recoating.
BOYSEN Epoxy Enamel
, ,
.
concrete.
, ,
masonry.
.
MIXING RATIO: 3:1, paint-to-catalyst, respectively
Concrete Flooring:
Finished acid etched texture should be similar to that of 40-60 grit sandpaper. Make sure that the surfaces to be painted are clean and dry.
Caution: Adequate protection and ventilation should be provided when working!
SURFACE PREPARATION
Remove oil and grease by detergent cleaning. For smooth surfaces, acid etch to improve adhesion. Do this by mixing one (1) part muriatic acid to one (1) part water. Apply over masonry and let stand for 2-3 minutes. Rinse with water to remove residual acid. If possible, rinse by pressure washing.
-
7/25/2019 Boysen Paints
12/15
Metal:
Wipe the surface with rag soaked in paint thinner to remove dust, dirt, grease, oil, wax and other foreign matter. For newG.I . sheets, etch the surface by applying 10%BOYSEN Metal Etching Solution #71 (dilute 1 part of B-71 to 9 parts water).
Concrete Flooring:
Mix three (3) parts of BOYSENEpoxy Primer White #2200 to one (1) part of its catalyst.
Metal:Prime base metal with BOYSENEpoxy Red Oxide Primer #2277 or BOYSENEpoxy Primer Gray #2230. Let dry 8 hours to overnight. Topcoat with 2-3 coats of BOYSEN Epoxy Enamel. Let dry overnight before recoating.
Water Tank (Interior)
. . - . . .
If repainting on surfaces with alkyd or lacquer-based coatings, scrape off all paint film to bare substrate. Remove oil and grease by detergent cleaning followed by scuff sanding. To remove rust, wire brush or scrape affected areas and apply BOYSEN Metal Etching Solution #71 over rusted portions. Let it stay for 10
surface thoroughly with water, letting it dry before applying paint. Primer should be applied immediately upon drying of the surface before rust sets in.
PAINTING SCHEDULE
Allowtwenty (20) minutes induction time. Thin 1:1 with Epoxy Reducer #55. Apply as primer coating on bare concrete floors. Let dry overnight. Mix BOYSEN Epoxy Enamel with its catalyst as with the procedure of the BOYSEN Epoxy Primer. Paint 2-3 coats of this mixture over well-primed surface. Allow 8 hours
rime are su srae wi poxy rimer i e . e ry ours o overnig . opcoa wi - coas o poxy name i e . e ry overnig eore recoaing. uring is sric y seven ( ) ays prior o use o an .
NOTE:
Foot traffic abrasion resistance fully develops after three (3) days of curing. For heavy duty application, allowseven (7) days of drying.
Application of topcoat should be done within 7 days after priming to ensure good intercoat adhesion, otherwise re-application of primer is needed.
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSEN Epoxy Primer
Ahigh quality, two-component, epoxy-polyamide
systemthat has exceptional adhesion to
practically any surface including steel tanks,
coastal installations, galvanized iron, pipelines,
aluminum, structural steel, etc. Has excellent
corrosion resistance and sealing properties.
Highly alkali-resistant so there is no need for
neutralization of newconcrete.
As a primer for topcoats of Epoxy Enamel
or Acqua Epoxyto be applied on metal,
galvanized iron, wood and masonry
20-25 square meter / 4 liters / coat 2-3 hours 6-8 hours 1.5 mils/coatBOYSENEpoxy Reducer
#55By Paint brush or spray gu
MIXING RATIO: 3:1, paint-to-catalyst, respectively
Concrete Flooring:
SURFACE PREPARATION
Remove oil and grease by detergent cleaning. For very smooth floors, acid etch smooth surfaces to improve adhesion. Do this by mixing one (1) part muriatic acid to one (1) part water. Apply over masonry and let stand for 2-3 minutes. Rinse with water. If available, rinse by pressure washing. Finished acid etched tex
60 grit sandpaper. Make sure that the surfaces to be painted are clean and dry.
Caution: Adequate protection and ventilation should be provided when working with acids.
Metal:
Wipe the surface with rag soaked in paint thinner to remove dust, dirt, grease, oil, wax and other foreign matter. For new G.I. sheets, etch the surface by applying 10%BOYSEN Metal Etching Solution #71 (dilute 1 part of B-71 to 9 parts water).
If repainting on surfaces with alkyd or lacquer based coatings, scrape off all paint. Remove oil and grease by detergent cleaning followed by scuff sanding. To remove rust, wire brush or scrape affected areas and apply BOYSEN Metal Etching Solution #71. Let it stay for 10-15 minutes. Be sure to wash off surface t
before applying paint. Primer should be applied immediately after treatment.
PAINTING SCHEDULE
-
7/25/2019 Boysen Paints
13/15
Concrete Flooring:
Mix three (3) parts of BOYSENEpoxy Primer White #2200 to one (1) part of its catalyst.
Metal:
Prime bare metal BOYSENEpoxy Red Oxide #2277 or BOYSENEpoxy Primer Gray #2230. Let dry eight (8) hours before recoating. Topcoat with 2-3 coats of BOYSEN Acqua Epoxyor BOYSENEpoxy Enamel. Let dry overnight before recoating.
NOTE: For epoxy-primed surfaces, topcoat should be applied not more than seven (7) days after priming to ensure good intercoat adhesion. Otherwise, re-priming is needed.
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
HudsonPolyurethane Floor Sealer is an
,
.
As a primer for parquet and other wooden
.
. . .
TWO-COMPONENT POLYURETHANE BASED COATINGS
Allowtwenty (20) minutes induction time. Dilute 1:1 ratio with BOYSENEpoxy Reducer #55. Apply as primer coating on bare concrete. Let dry overnight. Topcoat with 2-3 coats of BOYSEN Acqua Epoxyor BOYSENEpoxy Enamel. Let dry overnight before recoating. Let cure for 3 days before allowing foot traf
Hudson Polyurethane Floor
Varnish Sealer
aromatic, two-component urethane sealer to
provide good adhesion of Hudson
Polyurethane Floor Varnish Topcoat.
floors and counter-tops for subsequent
coating of HudsonPolyurethane Floor
Varnish Topcoat (indoor use).
20 - 25 sq.m./4 liters/coat Thirty (30) minutes One (1) hour 1.5 mils/coat Recoat after 6 hoursBy natural hair brush or air
spray
MIXING RATIO:
HudsonPolyurethane Floor Sealer is mixed 3.5 Liters to its 1/2-li ter catalyst. Enough mixture is made for four (4) hours work (maximum). Excess material will gel.
New Wood: Old Wood:
1. Use only kiln dried wood. 1. Remove loose paint to sound surface.
2. Countersink nail heads for putty application. 2. Scuff sand intact filmto provide anchorage for succeeding coats.
3. Sand rough wood until smooth, then dust off before painting. 3. If old coating is oil-based, scrape all existing paint to bare surface.
4. Surface to be painted should be clean and dry, free fromdust, dirt and other foreign matter. 4. Surface to be painted should be clean and dry, free fromdust, dirt and other foreign matter.
1st and 2nd coats: HudsonPolyurethane Floor Varnish Sealer
3rd to 5th: HudsonPolyurethane Floor Varnish Topcoat
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
Hudson Polyurethane Floor
Varnish Topcoat
HudsonPolyurethane Floor Varnish Topcoat is
an aromatic, two-component, urethane finish for
wooden surfaces that cure to a tough, non-slip,
mar resistant film.
Excellent for wood parquet, counter-
tops, and other wooden floorings (indoor
use).
20 - 25 sq.m./4 liters/coat Thirty (30) minutes One (1) hour 1.5 mils/coat Recoat after 6 hoursHudsonPolyurethane
ReducerBy camel brush or spray
MIXING:
SURFACE PREPARATION
PAINTING SCHEDULE
HudsonPolyurethane Floor Varnish Topcoat is mixed on a 3:1 ratio by volume to its catalyst. Enough material should be made for four hours work (maximum). Excess mixture will gel.
New Wood: Old Wood:
1. Use only kiln dried wood. 1. Remove loose paint to sound surface.
2. Countersink nail heads for putty application. 2. Scuff sand intact filmto provide anchorage for succeeding coats.
3. Sand rough wood until smooth, then dust off before painting. 3. If old coating is oil-based, scrape all existing paint to bare surface.
4. Surface to be painted should be clean and dry, free fromdust, dirt and other foreign matter. 4. Surface to be painted should be clean and dry, free fromdust, dirt and other foreign matter.
SURFACE PREPARATION
PAINTING SCHEDULE
NewWood - Apply 1 to 2 coats of HudsonPolyurethane Floor Varnish Sealer by brush or spray. Follow with 3 coats of HudsonPolyurethane Floor Varnish Topcoat applied by spray. Allow 7 days to fully cure before allowing heavy duty use and 3 days for foot traff ic abrasion.
-
7/25/2019 Boysen Paints
14/15
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSEN Aqu aseal #99
Anon-silicone protective sealer designed to
impart maximumwater repellancy to a wide
variety of above ground masonry and stone
surfaces. It minimizes unsightly efflorescence
and reduces cracking and spalling.
BOYSENAquaseal#99 enhances the
appearance of natural stone.
Functions as a clear penetrating sealer
on porous substrates to repel water and
moisture for brick, stucco, concrete,
hollowblocks, rubble, and sandblast
finish.
8 sq.m/ gallon 2 hours
Not necessary. Use paint
thinner for washing of
tools
by brush (do not spray)
BOYSENAquaseal#99 should be applied liberal ly to saturate the surface. Generous overlapping of passes is recommended until it dri ps down about 6 inches on masonry.
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
Is a water-based, lowVOCpaint for priming
previously painted masonry surfaces where the
.
As a primer when repainting chalky25-30 sq.m/ gallon 1-2 hours 2 hours
1.25 mils/coatnot necessary by brush/roller
SURFACE PREPARATION CHEMICALS
PAINTING SCHEDULE
I I
BOYSEN Chalk Blocker
#7304
I ,
existing paint fi lmis chalky.
surfaces .
.
(approximately)
For chalking old paint, use Boysen Chalk Blocker #7304 as primer.
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSEN Masonry
Neutralizer
Aliquid acidic substance that is to be mixed with
water to neutralize lime activity in new masonry
surfaces.
20 sq.m./gallon of mixture paint brush or roller
MIXING RATIO: 1 part BOYSENMasonry Neutralizer #44 to 16 parts clean water
1st step: Remove oil and grease by detergent cleaning.
2nd step: Apply diluted BOYSEN
Masonry Neutralizer and let stand overnight3rd step: Rough sand surface to remove efflorescence salts
Caution: Adequate protection and ventilation should be provided when working with acids.
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSEN Metal Etching
Solution #71
An acid type metal cleaner and rust converter. It
transforms rust and removes light deposits of
mill oil. B-71 destroys corrosion stimulators and
properly conditions metal surfaces for painting.
As preparation agent for painting on new
galvanized and rusty metal surfaces
25-30 sq.m./gallon of mixture depending
on surface rustinesswater paint brush
PAINTING SCHEDULE
PAINTING SCHEDULE
. I
.
.
. .
MIXING RATIO:
1. For treatment of new G. I. sheets: 1 part of Boysen Metal Etching Solution #71 to 9 parts water.
2. For rust treatment: use pure, limited over stubborn rust only.
NewGalvanized Metal: Rusted Metal Surface:
Step 1: Wipe the surface with rag soaked in paint thinner to remove dust, dirt, grease, oil, wax and other foreign matter. Step 1: Wire brush and scrape loose rust
Step 2: Apply 10%Boysen Metal Etching Solution #71 Step2: Apply pure Boysen Metal Etching Solution #71 on rust.
Step 3: Let stand for 10-15 minutes then wash off wi th water toremove residue. Let dry. Step 3: Let stand for 10-15 minutes then wash off wi th water toremove residue. Let dry.
PAINTING SCHEDULE
-
7/25/2019 Boysen Paints
15/15
Primer should be applied immediately after treatment.
Caution: Adequate protection and ventilation should be provided when working with acids.
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
BOYSEN Paint and Varnish
Remover #141
An effective wax-based paint stripper.
As preparation agent for repainting of
metal, wood and masonry surfaces where
the existing paint needs to be removed.
15-18 sq.m./gallon of mixture depending
on paint reaction.
paint brush. Use rubber
gloves when applying
DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION
Aspecial bonding paste that is mixed with
cement and applied on concrete to correct
. I
,
.
For both interior and exterior plastered
concrete, concrete slabs, acotech walls,
reinforced concrete walls, and pre-cast
.
0.4 kg /sq. m. / mm, recommended total
. .
30 min.; allow14 days
Apply with trowel or putty
.
PAINTING SCHEDULE
Apply BOYSENPaint and Varnish Remover #141 on painted surface. When the old paint has wrinkled after approximately 10 minutes, scrape off with the use of spatula or putty knife. Wash off residue by detergent washing followed by solvent washing with BOYSEN Lacquer Thinner.
BOYSENSkimcoat
surface imperfections prior to painting. It repairs
bubbles, honeycomb and concrete defects on
waviness and plumbness up to 4 mmthick.
, , ,
,
concrete surfaces in lieu of cement
plaster to eliminate surface defects and
make the surface smooth and ready for
painting.
. . . ,
thickness is from 0.3 - 4 mm.
.;
before painting
knife.
POTLIFE:Thirty (30) minutes
1. Remove oil, grease, dust, dirt , contaminants, and all loose grit and mortar from the surface.
2. Defects on concrete more than 5 mmthick should be corrected using mechanical sanders/grinders.
3. Moisten the concrete before application.
1. Using a steel trowel, apply the mixture thinly on the surface by pressing the edge of the trowel firmly on the concrete until all areas are covered.
2. Let it dry for at least 30 minutes before applying the second coat (if necessary).
3. If trowel marks are visible, let surface dry for at least 30 minutes before sanding to further smoothen surfaces.
4. No need to neutralize the surface. Allow at least 14 days before painting.
Note: Do not apply on painted surfaces.
APPLICATION
SURFACE PREPARATION
MIXING PROCEDURE: Put BOYSENSkimcoat#7750 on a suitable container (plastic bucket) and mix with cement at 1:1 ratio by weight until a lump-free homogeneous paste is reached. Do not add water. Use portland cement (for ordinary cement color) or white cement (to produce a white finish). No need to ne