biomass controllers - tem · biomass controllers ... · selection of operation mode off / manual /...
TRANSCRIPT
Biomass controllers
TEM AG Triststrasse 8 Switzerland Tel. +41 (0)81 254 25 11 [email protected]
CH-7007 Chur Fax +41 (0)81 254 25 39 www.tem.ch
)))
))) (((
)))
The hot wire to all components – eBUS
Simply ingenious: All devices of the TEM system are equipped with an eBUS interface. This makes the most complex problems
simple to solve and simple to be expanded at any time. The hot wire from TEM is of course also available as wireless versions, for
example as wireless temperature sensors, room devices. Through iCom, the system can also optionally be operated via PC/inter-
net. - An intelligent and future oriented system for an efficient control of heating appliances.
System controller
Solar controller
Biomass controller
Boiler controller
Heat pump controller
Heating circuitcontroller
Outdoor sensors
Room devices
Heating circuit controllers
Master remote control
Master remote control
Computer / web
via iCom
SE 601X SE 630X SE632X PFA 5520 BMC 020X OGZ FSK OGZ FSK OGZ FSK
OUTPUTS 230VAC Relay electro-mechanical up to 16 up to 8 up to 13 5 up to 13Electronically relays of it up to 13 up to 4 up to 10 3 5
INPUTSSensor 14 7 12 4 up to 7Digital inputs 4 6Optocoupler up to 6 up to 4 - - -Sensor O2 (Lambda) - - - - 1Pressure sensor 1 - - - 1Input set point value 1 1 up to 2 - 1
OUTPUTSet point value 0-10 V 1 up to 2 up to 2 - up to 2
Hydraulic applications up to 13 up to 13 up to 13 3 3
Voltage supply with all devices is: 230 VAC ±10% 50-60 Hz
TEM biomass controllers with integrated burner manager are available in different models. From simple heat distribution of a
non-controlled wood oven and the control and monitoring of a combustion process to complex, fully automatic operation of a
pellet boiler with automated fuel feed and cleaning functions. Whether simple or complex, common in all controllers is a well
thought out concept, an optimized degree of efficiency and high reliability.
Built in Wall device Wall device Wall device Built in
Firewood Firewood Firewood Pellets / Firewood Pellets / Firewood
Brilliant – heating with biomass has started
For many years, TEM has developed demanding solid fuel – boiler controls. Maximum comfort with minimum
energy consumption are in focus here. TEM offers boiler manufacturers comfortable, simple solutions which
are optimally designed for the respective situation. These tailor made products and the best quality are the
prerequisites for an optimal heating system.
SE 601X SE 630X OGZ FSK
The SE601X OGZ FSK by TEM are system controllers with specially supplemented solid fuel functions. The burning control
thus selectively works through a fan or air flap control. This allows for the integration of even natural ventilation ovens. The
heating up function works manually using a start key (fill door switch) or automatically by recognition of the temperature
increase. The SE601X OGZ FSK series are also available as wall versions.
Integrated functions
· Up to 2 heat generators, thereof 1 solid fuel
· 2 heating circuits and DHW preparation
· Solar function internally or with external TEM
solar controller
· Selection of operation mode manual / automatic
· Frost protection
· Heat demand automatic through eBUS or 0-10V
· Boiler pump control
· Boiler protection functions direct or through control
of heat distribution
· Sequence control for wood burning
· Heating up function using heating up key / fill door switch
or automatic recognition of temperature increase
· Modulation using 1 fan or 1 air flap
· Flue gas temperature control / limitation
Models and equipment
· Coded Rast-5 connectors or screwing terminals in
large terminal room
· Up to 16 voltage outputs (230VAC), thereof
max. 13 electronic
· Up to 14 low voltage inputs (sensor/switch)
· Up to 2 low voltage outputs
· Real time clock with power reserve and
automatic summer / winter time
· TEM eBUS (2 wires)
The 6-series from TEM
What fun is the most flexible controller if the operation is often a
test of your patience? The TEM master remote controls MB 6100
and MB 6400 with their clear menu structure are self explanatory, all
parameters are shown as text. The target and actual temperatures
can thus quickly be displayed, operating modes selected using direct
buttons and functions can be comfortably edited and activated.
PFA 5520
HR5851
Whether pellet burning oven, wood burning oven or wood burning boiler, the PFA 5520 has a grip on all these heat generators.
It controls and monitors the burning process and thus controls the power based on the flue gas temperature. In addition the
boiler pump can be controlled and the power adjusted depending on the temperature of a water heat exchanger or a storage
tank. With the HR 5851 room control device assembled in the living room, you thus have a comfortable room heating.
Integrated functions
· Sequence control with switching possibility
for wood or pellet operation
· Room temperature control with weekly
time program for pellet operation
· Boiler pump control
· Monitoring and controlling the flue gas temperature,
boiler temperature and the storage tank temperature
· Modulated power control
· Storage tank charging function
· Automatic ignition for pellet operation
· 1 feeding screw and 2 fans
· Wood heating up function using fill door switch
· Pressure monitoring
· Frost protection
· Selection of operating mode with OFF, automatic and
manual operation
· Error message
Models and equipment
· Compact housing for building in or wall assembly
· Large, concise terminal room
· 5 voltage outputs, thereof 3 electronic (230VAC)
· 8 low voltage inputs (sensor/switch)
· Real time clock with power reserve and automatic
summer / winter time (with HR 5851)
· TEM eBUS (2 wires)
· 230 VAC power supply
Perfect for pellets or wood
BMC 020X
Whether pellet oven or wood boiler, the BMC 020X controls the burning process and boiler temperature via flue gas
temperature and lambda probes. It also controls the pellet feed and pumps. In addition, cleaning and boiler protection
functions are already integrated. Through a separate operating device, all parameters can be comfortably set. The controller
can be operated in stand alone mode or in connection with a central heating system.
Integrated functions
Pellet boiler
· Sequence control for pellets burning
· Automatic ignition for pellet operation
· 2-stage pellet feed with 2 sensors and 3 actors
· Cleaning function for boiler / heat exchanger and
burner / ash removal
Wood boiler
· Sequence control for wood burning with fan and flap control
· Wood heating up function using heating
up key / fill door contact
General
· Power and burning control using flue gas temperature
and lambda probe
· Selection of operation mode Off / manual / automatic
· Frost protection
· Boiler protection functions direct or through control of
heat distribution
· Parameterizable output functions
· Error recognition
Models and equipment
· Coded Rast-5 connectors
· Up to 12 3pole voltage outputs, thereof
max. 5 electronic (230VAC)
· Up to 14 low voltage inputs (sensor/switch)
· Combustion chamber temperature Ni-CrNi
· Flue gas temperature NTC or PT 1000
· Lambda probe
· Up to 2 low voltage outputs
· Real time clock with power reserve and
automatic summer / winter time
Control and boiler protection – fully automatic
Integrated functions
Pellet boiler
· Sequence control for pellets burning
· Automatic ignition for pellet operation
· 2-stage pellet feed with 2 sensors and 3 actors
· Cleaning function for boiler / heat exchanger and
burner / ash removal
Wood boiler
· Sequence control for wood burning with fan and flap control
· Wood heating up function using heating
up key / fill door contact
General
· Power and burning control using flue gas temperature
and lambda probe
· Selection of operation mode Off / manual / automatic
· Frost protection
· Boiler protection functions direct or through control of
heat distribution
· Parameterizable output functions
· Error recognition
Models and equipment
· Coded Rast-5 connectors
· Up to 12 3pole voltage outputs, thereof
max. 5 electronic (230VAC)
· Up to 14 low voltage inputs (sensor/switch)
· Combustion chamber temperature Ni-CrNi
· Flue gas temperature NTC or PT 1000
· Lambda probe
· Up to 2 low voltage outputs
· Real time clock with power reserve and
automatic summer / winter time
A broad range of accessories from simple wired temperature to wireless sensors, or to the sophisticated remote
control units, rounds off the TEM system. A system solution - one fits the other. That is one of the reasons why a
TEM controller is easy to work with also during the installation and later when it is in operation.
ZTF 222 + ZTF223 ZTF 224 ZVF 210 ZAF 500 ZAF 600 RF
Technical specifications: Measurement range: -50 ... 90°C (ZTF 223 up to 180°C, ZTF 224 up to 250°C) | el. current < 1mA | sensor
element: NTC 5000 | Dimension: 6 x 50 x 0.4 mm | wire: 2 x 0.34 mm² | Available cable lengths: 1500 mm, 2500 mm, 4000 mm |
wireless outdoor sensor ZAF 600 RF
FB 6100 FS 6200 (RF) FB 6200 (RF) CO 6200 RF
The remote control units can be connected to all TEM eBUS heat controllers and allocated to a particular zone. For model 6200 two
designs are available: The FS 6200 without display with room temperature setting wheel as well as the FB 6200 with display for the
temperature and operating mode. The mode of operation is changed using a push button, the temperature through a setting wheel.
The CO 6200 RF is the wireless-eBUS-receiver which is connected using 2-wire connection to the eBUS. FS 6200 and FB 6200 are
available under the description RF also as wireless models.
MB 6100 MB 6400
Master remote control unit for programming and operating the SE devices. The display of the status, parameter, target and actual
values occurs in plain text. They are operated through the comfortable “press-turn” operating concept. For quick access of special
functions, there are 6 quick selection direct keys available. The remote control unit can be mounted in standard cutout (96x144mm)
(MB 6400) or on the wall (MB 6100).
System accessories
Tem
pera
ture
sen
sors
M
aste
r rem
ote
cont
rol
Roo
m te
mpe
ratu
re r
emot
e co
ntro
l
Heating appliances are becoming more and more complex:
Several mixed heating circuits, differing heating demands, sto-
rage tank configurations, utilization of solar energy, ecological
and economic requirements. It is no longer enough to simply
switch the heating appliance on or off. Already back in the early
eighties, TEM introduced several universally usable heat cont-
rollers, and the TEM system controllers today can easily cope
with the existing and future requirements. The core is a unique
energy management which determines the required heating
demands and calculates the therefore necessary heating capa-
city under consideration of the various available heat sources.
In spite of complex functionalities, TEM system controllers are
simple to mount and operate. An extensive range of accesso-
ries supports the installer in installation and operation.
TEM develops and produces electronics, hard- and software
for energy-efficient heating, ventilation and climate controls.
The leading know how is based on more than 40 years of
experience. A constant focus on research and development, an
excellent organized and structured production and after sales
service guarantees high quality and innovative products and
solutions.
TEM system– one thing fits the other
TEM AG Triststrasse 8 Switzerland Tel. +41 (0)81 254 25 11 [email protected]
CH-7007 Chur Fax +41 (0)81 254 25 39 www.tem.ch