biochar in agricultural productivity_technical report
TRANSCRIPT
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
1/63
Biochar: implications for
agricultural productivityJessica Sparkes and Peter Stoutjesdijk
Research by the Australian Bureau of Agricultural
and Resource Economics and Sciences
TECHNICAL REPORT 11.06December 0
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
2/63
Commonwealth of Australia
Ownership of intellectual property rights
Unless otherwise noted, copyright (and any other intellectual
property rights, if any) in this publication is owned by the
Commonwealth of Australia (referred to as the Commonwealth).
Creative Commons licence
All material in this publication is licensed under a Creative
Commons Attribution 3.0 Australia Licence, save for content
supplied by third parties, logos and the Commonwealth Coat
of Arms.
Creative Commons Attribution 3.0 Australia Licence is a
standard form licence agreement that allows you to copy,
distribute, transmit and adapt this publication provided
you attribute the work. A summary of the licence terms
is available from creativecommons.org/licenses/by/3.0/
au/deed.en. The full licence terms are available from
creativecommons.org/licenses/by/3.0/au/legalcode.
This publication (and any material sourced from it) should
be attributed as: Sparkes, J & Stoutjesdijk, P 2011, Biochar:
implications for agricultural productivity, ABARES technical
report 11.6. CC BY 3.0.
Cataloguing data
Sparkes, J & Stoutjesdijk, P 2011, Biochar: implications for
agricultural productivity, ABARES technical report 11.6,
Australian Bureau of Agricultural and Resource Economics
and Sciences,Canberra.
ISSN 189-3128 (online)
ISBN 978-1-74323-002-2 (online)ABARES project 43070
Internet
Biochar: implications for agricultural productivity is
available at: daff.gov.au/abares/publications.
Contact
Department of Agriculture, Fisheries and Forestry
Australian Bureau of Agricultural and Resource Economics
and Sciences (ABARES)
Postal address GPO Box 1563 Canberra ACT 2601
Switchboard +61 2 6272 2010
Facsimile +61 2 6272 2001
Email [email protected]
Web daff.gov.au/abares
Inquiries regarding the licence and any use of this document
should be sent to: [email protected].
The Australian Government acting through the Department
of Agriculture, Fisheries and Forestry has exercised due
care and skill in the preparation and compilation of the
information and data in this publication. Notwithstanding,
the Department of Agriculture, Fisheries and Forestry,
its employees and advisers disclaim all liability, including
liability for negligence, for any loss, damage, injury, expense
or cost incurred by any person as a result of accessing,
using or relying upon any of the information or data in this
publication to the maximum extent permitted by law.
Acknowledgements
The authors wish to acknowledge Dr Evelyn Krull for
providing review comments.
Front cover image courtesy of Black is Green Pty Ltd.
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
3/63
iii
Contents
Preface vi
A cautionary note vi
Summary vii
1 Introduction 1
2 Biochar production and characteristics 2Production technologies and systems 2
Potential feedstocks for biochar production 6
Biochar quality 9
3 Biochar applications in agriculture 14Application of biochar 15
Biochar for soil improvement 16
Biochar effects on soil biological activity 18
Nutrient transformation 19
Effects of biochar on plant growth 21
Agricultural impacts summary 27
4 Biochar as a carbon store 28Attainable carbon storage levels 28
Potential carbon storage levels 29
5 Biochar effects on greenhouse gas emissions 30Noncarbon dioxide greenhouse gas reduction potential with biochar application 30
Soil organic matter and carbon dioxide emissions 33
Ancillary benefits of biochar application 33
Avoided emissions from waste streams 34
6 Biochar for waste management 35
7 Renewable energy generation 36
8 Economic considerations in biochar production 37
9 Risks associated with biochar production and use 40Application rates 40
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
4/63
iv
Effect on agrochemicals 40
Biomass availability 41
Soil albedo 41
Soil residence times 42
Soil organic matter 42
10 Limitations and barriers to implementation 43
11 Current research 45
12 Research needs 46
13 Conclusion 47
References 48
Tables
1 Fate of biomass feedstock for different pyrolysis conditions 5
2 Typical components of fibrous biomass for use in pyrolysis and gasification 6
3 Typical thermal decomposition temperatures for common feedstock constituents 9
4 Mean ash content of biochars produced from various feedstocks using slow
pyrolysis at 550oC and 700oC with steam activation 11
5 Chemical attributes ofterra preta and adjacent control (un-amended) soils in theAmazon Basin 14
6 Summary of selected glasshouse and field trials 23
7 Economic analysis of fast and slow pyrolysis for biochar production using
crop stubble 37
Figures
1 A pyrolysis reactor 3
2 Portable on-farm BiGchar pyrolysis system 4
3 Large capacity slow pyrolysis industrial system 4
4 Potential biomass feedstocks for various pyrolysis conditions 7
5 Carbon recovery of different feedstocks with increasing temperatures 10
6 Objectives and motivations for applying biochar to soils 15
7 Change in soil pH with increasing biochar application rates to sandy soils 17
8 Effect of different biochar sources on pH in silt loam soils at increasing
application rates 17
9 Nitrogen cycle 19
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
5/63
v
10 Carcass nitrogen retention at the end of a 50-day feeding trial and cumulative
ammonia nitrogen excretion for 12 hours after adding bamboo char to the diets of
Japanese flounder (Paralichthys olivaceus) 27
11 Comparison of traditional biomass and biochar applications to soils on soil carbon
retention over 100 years 29
12 Sources and sinks for methane production (methanogenesis) and oxidation
(methane uptake) relevant to the agriculture sector 31
13 Analysis of the costs of biochar production and potential attainable revenue per
tonne dry feedstock for late harvest corn stover, switchgrass and yard waste 39
Boxes
1 Methane emissions 31
2 Nitrous oxide emissions 32
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
6/63
vi
PrefaceThis report presents findings of a desktop review into biochar, covering potential applications,benefits, costs and risks, and future research required to realise the agricultural productivityimprovement and environmental sustainability potential of biochar. This report focuses on
production and application of biochar to soils to improve soil function and the ancillarybenefits that may arise. Use of biochar as a way to abate greenhouse gases and sequester
carbon is discussed in only general terms.
Biochar production options are discussed to highlight feedstock biomass sources andproduction conditions that maximise biochar production for agricultural purposes. The report
describes biochar characteristics required to maximise agricultural productivity, followedby a detailed description of the potential benefits of biochar additions to plant and animal
productivity. The potential of biochar for carbon sequestration and waste management isalso discussed briefly. Finally, potential risks, barriers and limitations to biochar application are
discussed and knowledge gaps for future research identified.
A cautionary note
No standards exist that prescribe the composition or preparation of biochar to distinguish
it from charcoal produced as a fuel source. Within this report, biochar is defined as acarbonaceous material produced for application to agricultural land as part of agronomic
or environmental management; while the terms char and charcoal are used to describea carbonaceous material for no specific end use. To ensure production of safe biochar
products that are sustainably generated (carbon negative), minimum quality standards needto be developed to minimise the risks to agricultural productivity and the environment of
inappropriate use of biochar.
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
7/63
vii
SummaryBiochar is a stable, carbon-rich form of charcoal that can be applied to agricultural land as part ofagronomic or environmental management. It can be produced by pyrolysis; where biomass suchas crop stubble, wood chips, manure and municipal waste is heated with little or no oxygen.
The main focus of this report is on agricultural productivity benefits of biochar. Specifically,
information about the ef fects of biochar on the productivity of agricultural soils to which itis added has been analysed and documented. This reports focus is on Australian agricultural
systems and draws heavily from international and Australian research; it does not examine indetail, the use of biochar as a carbon sequestration mechanism.
Increased agricultural productivity and environmental sustainability are policy objectives for
many governments and this report seeks to provide decision makers with information aboutthese objectives in the context of biochar. Before any decisions can be made about using
biochar as a soil conditioner and a climate change mitigation tool, agricultural policy makersneed to understand the potential benefits and risks of its use in agricultural soils.
This report gives policy makers information about the:
processes and feedstocks available for biochar production
physical and chemical characteristics of biochar
effects of biochar application to agricultural soils
economic considerations of biochar production and use
risks associated with using biochar in agricultural systems
barriers to using biochar in agriculture.
Biochar feedstocks and production conditions can significantly influence the quality of biochar.
Further, due to biochars heterogeneous nature, its production and assessment is complex,prohibiting a simple classification or generalisation of the end product. This means production
conditions need to be optimised for each feedstock used to ensure the resultant product is fitfor purpose and it will deliver the intended effects when added to agricultural soils. Incorrect
production could result in a product that is detrimental to agricultural production and theenvironment.
There are signif icant potential productivity and other benefits from adding appropriate
biochars to Australian agricultural soils. These include improvements in physical and chemicalsoil characteristics, nutrient use ef ficiency and reductions in greenhouse gas emissions
derived from nitrogenous fertilisers. Generally, biochar has been found to improve infertileand degraded soils. However, not all crops behave the same way and not all soils show broadimprovements with biochar application; even when the biochar appears fit for purpose. Within
farming systems, biochar may also bind and reduce the efficacy of some agricultural chemicals.
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
8/63
Biochar: implications or agricultural productivity ABARES technical report 11.6
viii
Recently, researchers have focused on the potential of biochar to mitigate climate change bystoring carbon in soils in an inert and stable form. However, to do this in agricultural soils, the
addition of biochar should also benefit agricultural production as there are no viable methodsto separate biochar from soils once it is added. If biochar has negative or even neutral effects
on agricultural soils and systems, there may be no argument for its use. If it is beneficial toagricultural production, its use must also be of economic benefit.
Current knowledge about the effects of adding biochar to Australian agricultural soils is not
sufficient to support recommending its use. However, international and Australian research willaid decisions about its use when results become available. Australian research funded by theAustralian Government through the Climate Change Research Program and through research
and development corporations, will help answer questions around feedstock choice andproduction conditions for manufacture of beneficial biochars, as well as its impact in different
Australian farming systems. The current state of Australian research has been highlighted in
factsheets and brochures, produced as a result of the Climate Change Research Program (seewww.daff.gov.au/climatechange/australias-farming-future/climate-change-and-productivity-research).
Despite the uncertainty surrounding its production and use, some farmers are producing their
own biochar. This may result in a biochar product that has negative ef fects on agriculturalproduction, as well as falling short of its climate change mitigation potential. An environmental
sustainability analysis, including a life cycle analysis, will give an indication of the overall impactof biochar use in agricultural situations. Development of a classification and governance
system should then be used to promote the benefits from biochar use while limiting thepotential negative environmental effects from its production.
More research is needed before confident predictions can be made about biochars suitability
for use in Australian agricultural systems. To that end, the Australian Government and researchand development corporations are funding biochar research. The Australian Government
recently announced more funding for biochar research under the Carbon Farming Initiative.The Biochar Capacity Building Program will fund research that investigates mitigation of
greenhouse gas emissions, projects that demonstrate biochar use on farms and projects thatfacilitate development of of fset methodologies so biochar users can access both domestic andinternational carbon markets. Once more research results become available, it may be possible
to start investigating the economics of biochar production and use in Australia.
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
9/63
1
1
According to the Food and Agriculture Organization,
[development and implementation of ] productivity-increasing farming technologies that
are truly sustainable in the sense that they do not themselves inflict damage on the soil, water
and ecological resources as well as on the atmospheric conditions on which future food output
depends [is essential to maintaining food security and productivity] (FAO 2009).
For technologies to be effective, food security actions must be coupled with adaptation andmitigation measures that relate to climate change and sustainable management of natural
resources (G8 2009). Biochar, a product of the thermo-chemical pyrolysis of biomass, may beone such emerging technology to improve agricultural productivity and food security, while
potentially reducing greenhouse gas emissions.
As Johannes Lehmann, a leading researcher in the field, said biochar can be used to addresssome of the most urgent environmental problems of our timesoil degradation, food
insecurity, water pollution from agrichemicals and climate change (Renner 2007). Suchstatements within the media have given rise to the idea of biochar as a potential option to
increase food security. However, others remain sceptical about the potential of biochar tosecure food supplies and mitigate climate change (Ho 2010; Powlson et al. 2011). Production
and application of biochar in a global context may emerge as a win-win strategy for
agricultural productivity, environmental sustainability and climate change mitigation, butfurther research is needed to address concerns.
The modern concept of biochar for soil amendment originated from soils particular to the
Amazonian Basin, where charcoal from incompletely combusted biomass, such as wood fromhousehold fires and in-field burning of crop stubble has, over thousands of years, produced
highly fertile terra preta (literally black earth) soils. These soils have been found to containhigh levels of organic matter and nutrients when compared with adjacent soils and are now
used to produce fruit crops (Krull 2009). More recently, biochar is used extensively in Japan toaccelerate snow melt to extend the growing season (Sohi et al. 2010).
Terra preta soils have received widespread media coverage in recent times due to the
positive effects on crop growth and this has led to the belief that biochar was the importantingredient. However, on closer examination, terra preta soils contain residues from human
and animal waste, food scraps and other nutritious waste material that were not charred(Krull pers. com. 2011). As a result of media coverage, scientific interest in emulating terrapreta soils in modern agriculture is increasing. The addition of biochar to soils for enhancedsoil fertility and agricultural productivity is one such area that appears promising. Research
has illustrated the potential of biochar to improve soil health and fertility, soil structure andnutrient availability. Furthermore, biochar may become a viable method for long-term carbon
storage in soils, while providing other greenhouse gas emission benefits. However, extensivelife cycle assessments need to be undertaken before widescale biochar application to ensure
net benefits in both agricultural productivity and greenhouse gas mitigation are realised.
Introduction
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
10/63
2
2
Production technologies and systems
PyrolysisBiochar is most commonly produced through an energy conversion process known as pyrolysis;the heating of organic materials (such as crop stubble, wood chips, manure and municipal
waste) in the complete or near absence of oxygen (Schahczenski 2010). Pyrolysis converts easilybroken down organic matter into a highly stable form of carbon, which is mainly used as a
soil additive to improve nutrient retention and carbon storage (Krull 2009). In some instances,biochar can remain stable in soil for hundreds to thousands of years (Sohi et al. 2009). Worldwide,
41 million tonnes of biochar is produced annually (McHenry 2009). Other products of pyrolysismay include synthetic or synthesis gas (syngas) and pyrolysis liquor (bio-oil).
Syngas and bio-oilIf syngas and bio-oil are captured, they can be used as a renewable energy source or as
feedstock for producing other chemicals, such as food additives and pharmaceuticals. Syngasconsists of a variety of gases, such as carbon monoxide, hydrogen and methane and can be
burned to provide heat to the pyrolysis system, or to generate electricity for external use.Bio-oil can also be used to provide heat to the pyrolysis system, or used for fuelling heaters,
furnaces and boilers to generate heat and electrical energy (Maraseni 2010). Syngas can befurther refined to bio-diesel, while bio-oil can be used as a feedstock for producing chemicals
(Maraseni 2010).
Production methodsPyrolysis can occur on many different scales; from simple, low-input traditional kilns to large,highly efficient industrial plants. Humans have used temporary pits and kilns constructed
from earth, stones and wood for char production for thousands of years (Pratt & Moran 2010).Traditional pit kilns and mound kilns are a low cost method of producing char; particularly in
developing countries. Simple kilns are designed for batch pyrolysis, thereby losing the potentialto use the heat, syngas and bio-oil produced in the process for other applications (Brown 2009).
Although simple kilns are easy to use and incur low capital costs, they are highly polluting.
Further, efficiency of the system can be as low as 8 per cent due to air entering the kilns,gasifying biochar to carbon monoxide and carbon dioxide (Brown 2009) and producing
excess heat in the process. Modification of stoves and kilns used in rural areas of developingnations offers a cost-effective way to produce biochar, which is more efficient, emits less
pollution and improves the health of users (Pratt & Moran 2010). For example, bricks, concrete
Biochar production andcharacteristics
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
11/63
Biochar: implications or agricultural productivity ABARES technical report 11.6
3
and metal have recently been used to improve traditional kilns. Although these pyrolysissystems can produce biochar, other benefits such as production of energy from syngas and
bio-oil remain unavailable.
In contrast to kilns and pits, modern pyrolysis plants incur high capital costs and are expensiveto run, but may of fer the greatest returns in terms of ef ficiencies and greenhouse gas
abatement potential (Pratt & Moran 2010). Most modern pyrolysis plants operate a continuousprocess where pollution control is possible (Brown 2009). A simplified diagram of a continuous-
flow pyrolysis system is given in figure 1.
Small-scale pyrolysis plants that can be used on-farm or by small industries are available, withfeedstock inputs of 50 to 1000 kilograms per hour (figure 2). At a regional level, pyrolysis units
can be operated by cooperatives or larger industries, such as sugarcane growers, and can processup to 8000 kilograms of feedstock per hour (figure 3) (Talberg 2009). Pyrolysis plants offer
the advantage of capturing syngas and bio-oil to heat incoming feedstock or to be used as arenewable energy source in other applications, such as generating electrical or mechanical energy.
Rotary Drier
Kiln Burner Flue GasNaturalGas
Natural Gas
Pyrolysis Kiln
DryOrgan
ics
CharConditioner
Gasifer
Pacifc Pyrolysis
Char
Organics
DrierExhaust
Engine Exhaust Gas
Clean Syngas
Syngas
Refning
Syngas
Refning
RawSyngas
RawSyngas
CleanSyngas
GreenPower
Engine andGenerator
Heat toConsumer
AgricharTM
Biochar Product
A pyrolysis reactor1
Note: In this system, biomass (organics) is fed into the reactor where it is heated in an oxygen free environment. This causes breakdown
of the biomass into smaller and more volatile compounds, which are cooled and collected as syngas, bio-oil and biochar.
Source: Pacific Pyrolysis Pty Ltd
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
12/63
Biochar: implications or agricultural productivity ABARES technical report 11.6
4
Portable on-arm BiGchar pyrolysis system2
Photo courtesy of Black is Green Pty Ltd, Queensland
Large capacity slow pyrolysis industrial system3
Photo courtesy of Pacific Pyrolysis Pty Ltd.
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
13/63
Biochar: implications or agricultural productivity ABARES technical report 11.6
5
Two main pyrolysis systems are in use for processing biomass: fast pyrolysis and slow pyrolysis.Both result in production of the three co-productsbiochar, syngas and bio-oilwhere
the relative amounts and characteristics of each are controlled by the processing conditions(Roberts et al. 2010). Gasification systemswhere feedstock biomass is combusted in a
directly-heated reaction vessel with limited introduced airalso produce biochar but at lowerproportions than either fast or slow pyrolysis.
The composition of the feedstock, temperature and heating rates can be altered to provide
different amounts of each product (that is, syngas, biochar and bio-oil) and their inherentproperties (table 1). It is important to note that maximising biochar yields will always be at theexpense of bio-oil and syngas production, which could affect the economics of production.
In particular, it should be noted that production of biochar for agricultural purposes willprobably never be energy self sufficient. Ideally, systems would have some degree of flexibility
with respect to the proportions of biochar, syngas and bio-oil produced, so operators could
respond to seasonal fluctuations in demand for these products.
The terms fast and slow pyrolysis are indicative of the time in which vapours are driven of f
the biomass in the reaction vessel. Fast pyrolysis occurs at moderate temperatures, with veryshort vapour residence times and produces more bio-oil and less biochar than slow pyrolysis.Slow pyrolysis produces maximum yields of biochar due to the generally lower operational
temperatures and heating rates (Kwapinski et al. 2010). Slow pyrolysis best describes theprocess in less complex biochar kilns and pits.
The par ticle size and moisture content of the feedstock are also important considerations
when developing an efficient pyrolysis system as they will af fect biochar characteristics andquality. Wet feedstocks with large particle sizes will require greater amounts of energy to bring
the biomass to the desired temperature, decreasing the efficiency of the system (Kwapinski et
al. 2010). In a study using wastes from corn, olives and tea, Demirbas (2004) demonstrated the
1 Fate o biomass eedstock or diferent pyrolysis conditionsapproach conditions liquid solid gas
(bio-oil) (biochar) (syngas)
% % %
Slow Moderate temperature ~500oC 30 35 35
Long vapour residence time ~530 minutes
Moderate Moderate temperature ~500oC 50 20 30
Vapour residence time ~1020 seconds
Fast Moderate temperature ~500oC 75 12 13
Short vapour residence time ~1 second
Gasification High temperature >750oC 5 10 85
Vapour residence time ~1020 seconds
Source: Brown 2009
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
14/63
6
effect of a number of variables on biochar yield. First, lower reactor temperatures favour higheryields of biochar with a temperature of 177oC producing the most biochar. Second, larger
particles (sizes tested were 0.5, 1.0, 1.5 and 2.3 millimetres) yielded more biochar and third,feedstocks with a higher lignin content provided maximum biochar yields. The observations
of Demirbas (2004) regarding particle size confirm earlier work of Suuberg et al. (1996) where itwas found that increasing particle dimensions of cellulose pieces increased biochar yield from
approximately 2 to 8 per cent at a heating rate of 60oC per minute to 750oC.
Controlling operating conditions to improve process ef ficiency and optimise biocharproduction has not been explored extensively due to competing priorities from bioenergyproduction (Brown 2009). More research is needed to better understand the mechanisms
of biochar formation to ensure development of energy ef ficient pyrolysis plants that targetproduction of desired products and provide a degree of f lexibility with respect to the relative
amount of products produced. This may be achieved through modifying heating rates,
temperatures and pressures, or developing a f lexible reactor design and considering thesupply and type of feedstocks available.
Potential feedstocks for biochar production
Researchers are increasingly aware that biomass and organic wastes are valuable feedstocks for
pyrolysis that can produce biochar, syngas and bio-oil (Kwapinski et al. 2010). However, due tothe large effect a feedstock source has on the physico-chemical properties of biochar (such as
particle size, composition and pore sizes) careful consideration must be given to choosing thecorrect feedstock for the intended end use.
Cellulose, hemicellulose and lignin are the major components of fibrous biomass (such as
wood, crop stubble and bioenergy crops). However, the relative amounts of these componentscan vary considerably between different species of plants, as well as within the same species;
due to variations in soil type, time of harvest and climatic conditions (table 2) (Brown 2009).
2 Typical components o brous biomass or use in pyrolysis and gasicationeedstock cellulose hemicellulose lignin extractives ash
% a % a % a % a % a
Hybrid poplar 45 19 26 7 1.7
Willow 43 21 26 1
Switchgrass 32 25 18 17 6
Miscanthus 38 24 25 5 2
Maize stover 39 19 15 4.6
Wheat straw 38 25 14 10
Bagasse b 50 30 20
a Per cent of total weight on a dr y matter basis.Source: Brown, 2009; b Mousavioun & Doher ty, 2010
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
15/63
Biochar: implications or agricultural productivity ABARES technical report 11.6
7
Further, due to structural differences, each component of the biomass breaks down atdifferent rates when exposed to high temperatures. For example, cellulose is more resistant to
thermal decomposition than hemicellulose, while lignin is more difficult to break down thancellulose and hemicellulose. Greater proportions of residual biochar are therefore produced
with increasing proportions of lignin. As such, the most suitable materials to maximise biocharyields are woody types, with a high lignin content such as nutshells, residues from sawmills
and forest wastes (Demirbas 2004).
Figure 4 identifies various potential feedstocks, their ideal processing conditions and theirend-use applications to maximise potential benefits. For example, switchgrass (a bioenergycrop) may be used in both slow pyrolysis (450550oC, oxygen free environment, long biomass
and gas vapour residence times) and fast pyrolysis (450500oC, short biomass and gas vapourresidence times) to produce syngas, bio-oil and biochar for use as a soil amendment or as an
energy source for fuel production and heating, respectively (Brown 2009; Roberts et al. 2010;
Sohi et al. 2009). However, when considering a potential feedstock for biochar production,biomass availability and moisture content must also be considered to ensure continualoperation of the processing plant, with minimal energy input requirements.
biomass energy crops(corn, cereals, wood
pellets, palm oil,oilseed rape)
bioenergy residuescake
agricultural waste(wheat straw, hazelnutand peanut shells,waste wood, etc)
compost(green waste)
manure/animalwaste (chicken)
kitchen wasteplastic, food, etc
sewage sludge
FEEDSTOCKS PROCESS PRODUCT USES AND APPLICATIONS
Potential biomass eedstocks or various pyrolysis conditions4
Note: The figure also identifies specific end-uses and applications for products to maximise the benefits from the biochar produced.
Source: Sohi et al. 2009
ast pyrolsis(anhydrous)
slow pyrolysis(low temp. 450550oC,
O2-ree sometimes
steam)
slow pyrolysis(low temp. 600900oC,
O2-ree)
gasifcation(high temp.,
ast heating rate,O
2present)
ermentation,anaerobic digestion
and mechanicalbio-treatment
carbonisation(brown at 300oC,black at 380oC)
synthesis gasbio-oil liquid
biochar solid
syngas
biochar
activatedbiochar
combustibleethane, methane
biochar
ethanol
methaneand sludge
charcoal
heat
fuel (combusted to generate electricity
or converted to syngas) high value biochemicals used as food
additives or pharmaceuticals
soil conditioners/fertilisers
soil amendment (neutral/alkaline pH,
porosity retains water, cation exchange
capacity: robust benefits to plant growth
compared to high-temp char)
fuel (cooking and heat)
extreme porosity and surface area
water filtration and adsorption of
contaminants (gas, liquid or solid)
fuel (low yield, high reactivity) contamination of some feedstocks
(e.g. metal and plastic in kitchen waste)
may preclude use of sludge/char in soil
fuel (for electricity or cooking)
by-products (wood spirits, wood tar)
substitute for coal-derived coke in
metal smelting
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
16/63
Biochar: implications or agricultural productivity ABARES technical report 11.6
8
Australia has an extensive range of biomass suitable for pyrolysis, including broadacre graintrash/stubble, agricultural processing residues (macadamia nut shells, olive pips, bagasse
from sugar cane production and husks from cereals or rice), forestry residues (wood blocks,wood chips and tree bark) and grass residues (both improved pastures and native grasses)
(Bridgewater & Peacocke 2000; Lehmann et al. 2006; OConnell & Haritos 2010).
Mallee eucalypt trees could potentially be grown on arid and semi-arid lands in Australiafor both salinity control and as a biofuel feedstock (Abdullah et al. 2010; Garnaut 2008).
Planting mallee trees can help restore areas affected by dryland salinity and the leaves andupper branches can be harvested perennially as a biofuel feedstock. Despite the potential ofmallee trees for both ecosystem restoration and biochar/bioenergy production, a number
of processing and harvesting issues (such as developing integrated cropping strategies inextensive production systems and the ability to attract private sector investment) need to be
resolved before it has the potential to become commercially viable as a biochar production
industry (Bell 2005; McHenry 2009). Nevertheless, use of biochars produced from mallee trees forapplication to soils to improve agricultural productivity is being investigated.
Biochar can also be produced from manures and other animal wastes, including bone. Forinstance, dairy shed waste and chicken litter have been used to produce biochar (Cao & Harris
2010; Joseph et al. 2010; McHenry 2009). Many types of manure are anaerobically digested toproduce biogas (a mixture of methane and carbon dioxide) and it is possible that the remaining
solid by-products could be used in pyrolysis reactions to produce biochar.
Pyrolysis of these types of waste may produce both energy and a biochar product with relativelyhigh levels of plant nutrients, such as phosphorous, potassium, nitrogen, magnesium and
calcium. Containment and use of nutrient-rich manures and animal products for production ofbiochar may also have positive environmental effects including reduced nutrient run-off and
corresponding reductions in greenhouse gas emissions, such as methane and nitrous oxide(He et al. 2000). Although manure and municipal waste may be used in pyrolysis, the high risk of
contamination from toxic chemicals and heavy metals may limit its use on agricultural soils.
The mineral content of potential biomass feedstocks must also be considered. Nik-Azar et al.(1997) found that impregnating woody biomass with sodium, potassium and calcium increasedbiochar yields by up to 15 per cent. These findings are in agreement with other studies, where
addition of inorganic salts (magnesium chloride, sodium chloride, iron sulphate and zinc chloride)
increased production of char from 5 per cent (control feedstock; no addition of salts) to 8, 14,17 and 28 per cent respectively (Varhegyi et al. 1988). However, addition of any minerals tofeedstocks to increase biochar yield would, from an agricultural productivity perspective, have to
be weighed against the effect of those minerals on soil structure, soil fertility and plant growth,and the cost of supplying these nutrients through other means. See Nutrient content of biochars
below for information on the natural nutrient content of biochars.
Not all agricultural waste materials are suitable for biochar production for agricultural purposes(Lehmann et al. 2006; McHenry 2009). Some production conditions and feedstock types can
cause the resulting biochar to be ineffective in retaining nutrients and susceptible to microbial
decay (McHenry 2009). Depending on the biomass source, some biochar products, suchas municipal waste, may contain high levels of toxic substances (heavy metals and organicpollutants) which must also be considered in the context of adding biochar to agricultural soils
(Lehmann et al. 2006).
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
17/63
Biochar: implications or agricultural productivity ABARES technical report 11.6
9
Biomass availabilityAvailability of large quantities of biomass feedstock and the transportation distance to a
pyrolysis plant are essential considerations for an efficient and economically viable biocharproduction system (Roberts et al. 2010). Lehmann et al. (2006) indicated that nut shells, bagasse
and olive and tobacco waste are all highly suitable feedstocks due to the location of farms,and their existing processing facilities, and because of the large biomass quantities produced.
For example, bagasse production in Queensland produces approximately 12 million tonnesannually (Krull 2009).
It is possible to co-locate pyrolysis plants with biomass processing operations (for example,
in the sugar cane industry) to minimise handling costs and provide a waste managementsolution. Production of biochar has the potential to be scaled to any level of production basedon location and feedstock quantities and quality. As such, pyrolysis systems can be developed
for on-farm production or at a regional or state level.
Biochar quality
As biochar can be produced from any biomass feedstock, it is essential to develop quality
standards to ensure non-toxic biochar is produced sustainably. Kwapinski et al. (2010) supportthe idea that feedstocks should be ranked according to their suitability for biochar production
for agricultural soil application and that guidelines should be developed to ensure adequateplanning of feedstock use.
Both feedstock type and pyrolysis conditions affect the physico-chemical characteristics of
biochar. Due to the range of biomass options and pyrolysis systems available, the variability inbiochars that can be produced is high. This variability has significant implications for nutrient
content of the biochar and nutrient availability to plants when biochar is applied to soil(Downie et al. 2009).
Generally, lower maximum temperatures, slower heating rates and higher pressures in the pyrolysis
system, and greater proportions of lignin in the biomass feedstock produce larger biochar yieldsat the expense of syngas and bio-oil production (Demirbas 2004; Downie et al. 2009). Apart from
affecting the quantity of biocharproduced, pyrolysis conditions
also have an effect on the qualityof the biochar produced. Forexample, Downie et al. (2009)
indicate that at temperatures above120oC, chemically bound moisture
is released, while at 200260oChemicellulose and cellulose begins
to decompose (table 3). This hasimportant implications for the
porosity and carbon content of the
resultant biochar.
3 Typical thermal decompositiontemperatures or common eedstockcomponenteedstock component decomposition temperature (oC)
Water >120
Hemicellulose 200260
Cellulose 240350
Lignin 280500
Data adapted from Downie et al. 2009.
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
18/63
Biochar: implications or agricultural productivity ABARES technical report 11.6
10
Carbon contentWhen producing biochar for long-term carbon sequestration in soils, carbon content is almost
the sole consideration, but when producing biochars to improve agricultural productivity,
the carbon content of the biochar is not the main focus. Other factors of greater importanceinclude structural characteristics and ion exchange capabilities (see Structural characteristics
and Ion exchange capacities below).
The carbon content of different biochars is variable and is dependent on both the feedstockused and the pyrolysis conditions (figure 5). Generally, carbon concentrations increase with
higher temperatures, with a coinciding decrease in biochar yield (Lehmann et al. 2006; Sohi etal. 2009). One study demonstrated a decrease in biochar yield from 67 to 26 per cent, with a
corresponding increase in carbon content from 56 to 93 per cent at temperatures of between300 and 800oC (Sohi et al. 2009). Baldock and Smernik (2002) found a similar trend in char yield;
where the char mass ofPinus resinosa sapwood decreased from 97 to 19 per cent when the
temperature increased from 150 to 300oC. This relationship becomes less pronounced beyond acertain temperature threshold, where an increase in temperature does not af fect carbon content(figure 5). This can be seen in Baldock and Smerniks (2002) work where temperatures above
350oC did not result in a significant decrease in char yield.
Due to its aromatic structure, biochar carbon is also chemically and biologically more stable thancarbon in the original biomass. This has important implications for carbon sequestration and is
the reason there is so much interest in biochar as a climate change mitigation tool. Lehmann etal. (2006) found that through conversion of biomass to biochar, about 50 per cent of the initial
carbon was retained, compared with the low amounts retained after burning (3 per cent) and
natural decomposition (less than 10 to 20 per cent after 5 to 20 years), depending on the type ofbiomass used (see also chapter 4).
30
Carbon recovery o diferent eedstocks withincreasing temperatures5
35
40
45
50
55
60
65
200 300 400 500 600 700 800 900 1000 1100
Note: The thresholds where an increase in temperature does not increase carbon content.
Source: : Lehmann et al. 2006
temperature (OC)
carbonrecovery(%o
finitialC)
hazelnut kernel husk
undefined wood
spruce wood
corn cob
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
19/63
Biochar: implications or agricultural productivity ABARES technical report 11.6
11
Ash contentThe ash content of biochar includes the inorganic constituents (calcium, magnesium and
inorganic carbonates) after all the organic elements (carbon, hydrogen and nitrogen) have
been volatilised (Joseph et al. 2009). The feedstock source and pyrolysis conditions have beenshown to affect the inorganic ash content of biochar, which in turn could affect potential end
uses (Kookana et al. 2011). Woody feedstocks generally produce char with low ash content(less than 1 per cent), while some grasses and straws are high in silica and produce up to
24 per cent ash in the char (Joseph et al. 2009). However, under certain processing conditionsand when the feedstock has high silica content, the resultant biochar has the potential to
cause silicosis in humans; appropriate precautions (such as face masks) should therefore beused (Krull pers. comm. 2011; Shackley & Sohi 2010).
Bagreev et al. (2001) reported ash
content increasing from 61.7 per cent to
76.8 per cent when sewage sludge washeated at 400oC and 800oC, respectively.In contrast, Singh et al. (2010a) found
that increasing the pyrolysis temperaturecaused ash content of various biochars
to decrease (table 4). This trend wasmost pronounced when paper sludge
was used as the feedstock. As such, ifash content is found to be a favourable
trait, further research may be needed to
identify the effects of temperature onash content to ensure optimal levels areapplied to soils.
Structural characteristicsThe structure of biochar can inf luence some of its quality characteristics. The porosity and
surface area of biochar are particularly important and have a large role in determining itspotential end use. The initial macrostructure of a feedstock is similar to that of the resulting
biochar and this is particularly the case for plant materials that are high in cellulose
(Sohi et al. 2010). As pyrolysis removes mainly volatile compounds, the macrostructure of thebiomass is to a large extent retained in the biochar. However, structural stress causes cracks inthe macrostructure, and escape of volatilised gases causes smaller pores and openings in the
material (Downie et al. 2009).
The surface area and porosity of biochar under different pyrolysis temperatures has potentiallysignificant effects on water holding capacity, adsorption capacity (ability of particles to stick
to the surface of biochar) and nutrient retention ability (Downie et al. 2009; Sohi et al. 2010).Bagreev et al. (2001) illustrated that the increase in porosity and hence surface area of biochar
is related to the temperature of pyrolysis. Boateng (2007) found that the surface area of biocharproduced from switchgrass was low; ranging from 7.7 to 7.9 square metres per gram. Another
study reported similar initial results, but then showed that biochar surface area increased by
4
Mean ash content o biocharsproduced rom various eedstocksusing slow pyrolysis at 550oC and700oC with steam activation
eedstock used ash content (g/kg)
550oC 700oC
Eucalyptus salignawood 42 4 37 2Eucalyptus saligna leaves 99 1 40 1
Paper sludge 654 5 475 6
Poultry litter 459 2 444 1
Cow manure 762 6 757 5
Source: Singh et al. 2010a
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
20/63
Biochar: implications or agricultural productivity ABARES technical report 11.6
12
a factor of three as the pyrolysis temperature increased from 400 to 950oC (41 to 99 squaremetres per gram, respectively) (Bagreev et al. 2001). These results and those of Keiluweit et
al. (2010) demonstrate a general trend of increasing surface area of biochars with increasingpyrolysis temperatures. Keiluweit et al. (2010) also illustrated that increasing porosity (and
hence surface area) is coupled with reductions in total carbon and volatile matter.
While the mechanisms of increased water holding capacity of soils amended with biochar arenot well understood, it is well known that the surface area of soil particles strongly influences
its water holding capacity; sand holds little water and clay holds a lot. Adding biochar to soilsto increase surface area may have an impact on water holding capacity. While it is generallyaccepted that biochar tends to increase water adsorption capacity and infiltration rates of some
soils, some researchers have reported that some biochars produced at low temperatures (400oC)may be hydrophobic, which could limit their effectiveness to store water (Day et al. 2005).
Low temperature pyrolysis conditions may also produce biochars suitable for use as a nitrogenfertiliser substitute (Day et al. 2005), while biochars created at high temperatures would be bestsuited to adsorption activities such as reducing heavy metal contamination in soils
(Sohi et al. 2010). In contrast, Boateng (2007) indicated that biochars produced at 480 oC hadpoor adsorption characteristics without further activation. Furthermore, it has been found that
biochar produced at low temperatures are brittle and prone to abrasion (Day et al. 2005). Assuch, the porosity and surface area of biochar may not affect the quality of the product over
the long term.
Ion exchange capacitiesThe nutrient retention capacities of biochars (and soils) depend on their cation exchange
capacity and their anion exchange capacity (Chan & Xu 2009). Cations (positively chargedions) and anions (negatively charged ions) are attracted to the opposite charge. Plant mineralnutrients such as calcium, phosphorus, potassium and nitrogen are present in soil water
(soil solution); predominantly as cations and in some cases anions. In soils, small particles, suchas those of humus and clay, carry negative charges and therefore attract cations, while anions
are relatively free to move in the soil solution and are both freely available for uptake by plantsand for leaching. Cation exchange capacity determines the soils ability to hold cations and, as
a general rule, the higher the cation exchange capacity the more fertile the soil.
Biochar has an appreciable anion exchange capacity and can therefore adsorb anionnutrients (such as nitrate and phosphate) and when they are incorporated into simple organic
molecules. Researchers have shown that biochars produced at low temperatures have ahigh cation exchange capacity, while those produced at high temperatures (greater than
600oC) have limited or no cation exchange capacity (Chan et al. 2007; Lehmann 2007a; Navia& Crowley 2010). This finding would suggest that biochars for soil amendment should not
be produced at high temperatures. Additionally, freshly produced biochars have little cationexchange capacity, while their anion exchange capacity is substantial. As biochar ages or
matures in the soil, its cation exchange capacity increases.
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
21/63
Biochar: implications or agricultural productivity ABARES technical report 11.6
13
High cation exchange capacity biochars have the ability to adsorb heavy metals and organiccontaminants such as pesticides and herbicides from the environment (Navia & Crowley 2010).
Use of biochars for environmental remediation is discussed in the scientific literature, but isbeyond the scope of this report. However, addition of biochar to agricultural soils as a soil
ameliorant is predicted to adversely affect the efficacy of agrochemicals, such as herbicidesand pesticides (Jones et al. 2011a; Kookana 2010; Smernik 2009). These effects will need to be
understood before widespread application of biochar to agricultural soils occurs.
Nutrient content of biocharsIn general, the nutrient content of biochar reflects the nutrient content of the feedstock.Biochar derived from manure or bone is relatively high in nutrients, especially phosphorous.
Of the biochars produced from plant material, those produced from wood generally havelow nutrient levels and those produced from leaves and food processing waste have higher
nutrient levels. Pyrolysis conditions also af fect nutrient content and availability.
High pyrolysis temperatures may decrease nitrogen content and availability. Total nitrogencontent was found to decrease from 3.8 to 1.6 per cent when the pyrolysis temperature was
increased from 400 to 800oC, respectively (Bagreev et al. 2001). Another study reported asimilar effect on the nitrogen content in both woody and herbaceous char: nitrogen was
gradually released from the char samples, beginning at 400oC and continuing through to750oC, at which time slightly more than half the initial nitrogen remained (Lang et al. 2005).
In addition to partial loss of nitrogen, a reduction in availability of the remaining nitrogen toplants was also found (Bagreev et al. 2001). An explanation for this proposes that the remaining
nitrogen becomes incorporated into the carbon matrix, limiting the availability of nitrogen inthe biochar produced (Bagreev et al. 2001; Chan & Xu 2009; Macias & Arbestain 2010).
pHBiochars used to improve soils are usually alkaline and, as will be discussed later, may have
the effect of raising the pH of soils to which they are added. However, not all biochars arealkaline. The pH of biochars can range from 4 to 12 depending on the feedstock used and the
pyrolysis conditions (Bagreev et al. 2001; Lehmann 2007b). Further, it has been observed thatincreasing the pyrolysis temperature can increase the pH of some biochars. It has been found
that increasing the pyrolysis temperature from 310 to 850oC, biochar produced from bagasse
increased in pH from 7.6 to 9.7 (Sohi et al. 2010). Although high pH biochars can be produced,they may not have a big impact on the pH of soils to which they are added; this effect isrelated to biochars acid neutralising capacity.
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
22/63
14
3
Biochar production and use is not a new phenomenon. Throughout the Amazon Basin, there
are areas ofterra pretahighly fertile dark-coloured soilsup to 2 metres deep, covering areasof up to 2 hectares (Talberg 2009). These soils were created by pre-Columbian indigenous
farmers who covered their fields with burnt remains of domestic and agricultural trash(Casselman 2007). The high fertility ofterra preta soils has been attributed to high levels of
organic matter from the addition of materials such as charcoal, residues from human andanimal waste, food scraps and other nutritious waste material that were not charred
(pers. comm. Krull 2011). Terra preta soils have a carbon content of up to 150 grams per kilogram ofsoil, compared with 20 to 30 grams per kilogram in adjacent un-amended soils (Novotny et al. 2009).
Further, the carbon is mainly in the form of black carbon, which is up to six times more stable thanthat in adjacent, un-amended soils (Novotny et al. 2009).
In addition to increased carbon content, terra preta soils are characterised by higher pH, calcium,magnesium and phosphorous levels, higher cation exchange capacities and higher base
saturation levels, compared with adjacent un-amended soils (table 5) (Novotny et al. 2009).This has important implications for the soils physical, chemical and biological properties
(discussed later in this chapter). Due to these characteristics, terra preta soils are now used toproduce crops such as mangoes and papaya, which reportedly grow three times faster than in
the surrounding unimproved soils (Sohi et al. 2010).
Recently, biochar has been manufactured with four complementary and generally synergisticobjectives in mind: soil amelioration to improve agricultural productivity, waste management,climate change mitigation and energy production (Roberts et al. 2010). Figure 6 identifies
the interactions between the differing objectives and motives for biochar productionand application. These competing priorities may pose issues for future large-scale biochar
production, where one will come to dominate at the cost of others (Pratt & Moran 2010). Asthe primary focus of this report is use of biochar for agricultural productivity and soil carbon
storage, it will only briefly discuss the other objectives.
Biochar applications inagriculture
5 Chemical attributes oterra pretaand adjacent (un-amended) soils inthe Amazon BasinSoil pH Ca + Mg (a) CEC P (b) base saturation (c)
(cmolc
kg- 1) (mg kg-1) %
Control 4.4 1.3 9.5 5 21
Terra preta 5.4 6.8 17.3 300 55
a Exchangeable. b Mehlich. c Base saturation = (Ca + Mg + Potassium) / CEC.
Note: CEC = cation exchange capacity.Source: Novotny et al. 2009
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
23/63
Biochar: implications or agricultural productivity ABARES technical report 11.6
15
mitigation oclimate change
wastemanagement
energyproduction
soilimprovement
social, fnancial benefts
Objectives and motivations or applyingbiochar to soils6
Source: Lehmann & Joseph 2009a
Researchers have been conducting biochar field trials on varying soil types and withindifferent parts of the world since 1980 (Talberg 2009). These trials have focused mostly on
tropical or semi-tropical regions in South America and South-East Asia (Blackwell et al. 2009;Talberg 2009; Verheijen et al. 2009).
Research is currently underway todetermine the effects of biocharin an Australian context through,
for example, the Climate ChangeResearch Program (DAFF 2011)
and projects within the GrainsResearch and Development
Corporation (GRDC 2011). However,the long-term effects of biochar
application are still unknown, with
available information generally onlyrelating to the first few years afterapplication (Verheijen et al. 2009).
As well, information on the effectof biochar on pastures, fodder
shrubs and trees, and within dryand temperate climates is limited
(Blackwell et al. 2009). Research toidentify the long-term effect of
biochar additions on specific soiltypes and climatic areas is needed
to further understand the effects ofbiochar within an Australian context.
Application of biochar
Owing to the variability of biochar types and potential applications, limited information isavailable to farmers on how best to apply it (Casselman 2007; IBI 2011). However, with currentresearch and the potential of biochar use to become widespread, it is possible that application
guidelines and specific machinery will be developed for its application.
There are a number of options for applying biochar and include deep banding with manures orcomposts, applying through liquid slurries and spreading by hand or machine; however, most
have not been extensively researched. Field trials to date have spread biochar and incorporatedit into the soil through some form of tillage (Blackwell et al. 2009). This method of application
minimises biochar movement though soil erosion, but may pose challenges for pastureapplication and no-tillage farming (Blackwell et al. 2009; Sohi et al. 2009).
In addition, strategies on timing and location of biochar application need to be developed.
Due to the relatively small amounts of biochar produced compared with the initial biomass
feedstock volume and the land harvesting area, it may not be feasible to apply the biochar backto the entire harvested area. Rather, biochar may be sequentially and annually applied to thefeedstock harvest area on a hectare-by-hectare basis, where farmers have access to a small-
scale, on-site pyrolysis plant.
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
24/63
Biochar: implications or agricultural productivity ABARES technical report 11.6
16
Biochar for soil improvement
Application of biochar as a soil amendment may be a valuable tool to enhance infertile and/or degraded lands. When applied to soil, biochar may improve nutrient supply to plants, as
well as the physical and biological properties of the soil. However, due to the irreversibility ofbiochar application, researchers need to conduct long-term studies to achieve a high level of
certainty that adding biochar to agricultural soils, for whatever reason, will not negatively affectsoil health and productivity.
Soil bulk density and water holding capacityMost researchers agree that adding biochar to infertile soils decreases its bulk density andincreases its water holding capacity. Adding biochar to infertile soil increases porosity, by the
nature of its particle size and shape, and because of biochars particularly porous internal
structure. In addition, increased soil porosity increases the surface area of soil so water is betterable to penetrate.
Ion exchange capacitySoil with a high cation exchange capacity has the ability to hold or bind cationic plantnutrients on the surface of biochar particles, humus and clay, so nutrients are available for
uptake by plants. A high cation exchange capacity means applied nutrients are held in soilsrather than leached in times of high rainfall. High soil cation exchange capacity translates
to a soil with high buffering capacity; meaning that addition of acidic or basic components
has a smaller effect on soil pH (until a certain point). For example, a high-cation exchangecapacity soil will take a longer time to develop into an acidic soil compared with a lower-cationexchange capacity soil. Conversely an acidic soil with a high cation exchange capacity will
need application of more lime to correct the soil pH compared with an acidic soil with a lowercation exchange capacity.
A number of studies have illustrated that biochar can increase the cation exchange capacity
of the soil. Once fresh biochar is exposed to oxygen and water in the soil environment,spontaneous oxidation reactions occur, resulting in an increase in the net negative charge
and hence an increase in cation exchange capacity (Joseph et al. 2009). As such, aged biocharparticles are associated with high concentrations of negative charge, potentially promoting
soil aggregation and increasing nutrient availability to plants (Liang et al. 2006; Major et al.2010a). However, Granatstein et al. (2009) found that cation exchange capacity did not changesignificantly as a result of biochar application, although there was a trend of increasing cation
exchange capacity when added to soils with a low initial cation exchange capacity.
Inyang et al. (2010) also measured the anion exchange capacity in bagasse biochars andsuggest that the addition of biochar would significantly enhance the exchange capacities
(cation and anion) of soils and improve their nutrient holding capacities.
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
25/63
Biochar: implications or agricultural productivity ABARES technical report 11.6
17
Soil pHpH is a measure of the acidity or alkalinity of a solution and is an important characteristic
of soils in terms of plant growth. Most plants have a preferred pH range where maximum
growth and production can be attained. However, most of Australias crop species need onlyslightly acidic to neutral soils. Due to the differential uptake and distribution of positively and
negatively charged ions, plant growth, fertiliser application and crop harvesting acidifies soils.It is usual practice to amend acidic soils by adding agricultural lime to raise the pH, which
allows plants to grow at their maximum potential (when other requirements such as water andnutrient availability are met).
A recent study found varying pH effects when different types of biochar were added to the
soil (Granatstein et al. 2009). This study noted that soil pH increased from 7.1 to 8.1 when39 tonnes per hectare of herbaceous feedstock derived biochar was added to a sandy soil. The
increase in pH was less pronounced for biochars from woody feedstocks (figure 7). A smaller
overall pH increment was observed when all types of biochar were applied to silt loam soilsat rates up to 39 tonnes per hectare (figure 8). Notably, pH increases in the sandy soil reacheda plateau at a biochar application rate of around 20 tonnes per hectare. In loamy soil types, a
similar plateau effect at 20 tonnes per hectare was observed, but showed additional increasesat the rate of 39 tonnes per hectare. The authors suggested that the smaller pH increases in
loam soils was due to the high initial cation exchange capacity (and hence, a high bufferingcapacity) of the loams.
Change in soil pH withincreasing biochar application
rates to silt loam soils
8
softwood bark
switchgrass
digested fibre
wood pellets
4.4
40302010
Source: Granatstein et al. 2009
rate o biochar application(tonnes per hectare)
pH
4.6
4.8
5.0
5.2
5.4
Change in soil pH withincreasing biochar application
rates to sandy soils
7
digested fibre
switchgrass
softwood barkwood pellets
6.8
7.0
7.2
7.4
7.6
7.8
8.0
8.2
40302010
Source: Granatstein et al. 2009
rate o biochar application(tonnes per hectare)
pH
Note: The range o pH values is diferent in each gure.
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
26/63
Biochar: implications or agricultural productivity ABARES technical report 11.6
18
Nutrient content
The pyrolysis operating conditions and biomass feedstock af fect both the composition and
structure of biochar, resulting in significant differences in nutrient content. Moreover, thevariation in the physico-chemical nature of biochars causes variability in the availability of
nutrients within each biochar to plants. Biochars derived from manure and animal-productfeedstocks are relatively rich in nutrients when compared with those derived from plant
materials and especially those derived from wood. However, biochars in general are probablymore important for use as a soil amendment and driver of nutrient transformation and less so
as a primary source of nutrients (DeLuca et al. 2009).
Biochar effects on soil biological activity
Soils can be viewed as complex communities of organisms which are continually changing inresponse to soil characteristics and climatic and management factors, especially the additionof organic matter (Thies & Rillig 2009). However, addition of biochars to soils is likely to have
different effects on soil biota (all organisms living within the soil) compared with addition offresh organic matter (biomass). The differences arise because of the relative stability of biochar
and the general lack of energy and biologically useable carbon in comparison with freshorganic matter.
Nevertheless, addition of biochar to soils affects the abundance, activity and diversity of soilbiotic communities. Biochar addition to soils can stimulate microorganism activity in the soil,
potentially affecting the soil microbiological properties (Hammes & Schmidt 2009). Rather thansupplying microorganisms with a primary source of nutrients, biochar is thought to improve
the physical and chemical environment in soils, providing microbes with a more favourablehabitat (Krull et al. 2010).
Biochar, because of its porous nature, high surface area and its ability to adsorb soluble organic
matter and inorganic nutrients, provides a highly suitable habitat for microbes. This is truefor bacteria, actinomycete and arbuscular mycorrhizal fungi from which some types may
preferentially colonise biochars depending on its physio-chemical properties. Biochar poresmay act as a refuge for some microbes, protecting them from competition and predation.
Microbial abundance, diversity and activity are strongly influenced by pH. The buf fering
capacity (that is, the ability of the soil solution to resist changes in pH) imparted by biocharcation exchange capacity may help maintain appropriate pH conditions and minimise pHfluctuations in the microhabitats within biochar particles.
Biochar is relatively stable and has long soil residence times, which suggests that biochar
is not a good substrate (food) for soil biota. However, biochars freshly added to soils maycontain suitable substrates to support microbial growth. Depending on feedstock type
and production conditions, some biochars may contain bio-oils or recondensed organiccompounds which could support the growth and reproduction of certain microbial groupsover others. The implications of this are that microbial communities in biochar will change over
time once it has been added to the soil. In addition, there could be a concomitant change inthe range of ecological roles filled and services provided by successive communities. It may
be that ecosystem services which are beneficial for agriculture, such as nutrient cycling ormineralisation of organic matter, develop over time.
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
27/63
Biochar: implications or agricultural productivity ABARES technical report 11.6
19
Nutrient transformation
Nitrogen is a very important plant nutrient. Application of biochar to soils may aidtransformation of nitrogen, potentially improving its availability to plants. Soil biota is
responsible for biotic fixation of atmospheric nitrogen and for nitrogen mineralisation.Nitrogen mineralisation refers to transformation of nitrogen held in organic forms (such as
humus and decaying plant and animal matter) to forms available for uptake by plant roots;namely ammonium and nitrate. Mineralisation consists of two major transformations that are
catalysed by dif ferent groups of biota. Firstly, organic nitrogen is ammonified to ammoniumand then nitrified to nitrate (figure 9).
Biochar has been found to increase nitrification rates in natural forest soils that have very lownatural nitrification rates. However, in agricultural soils, which already have appreciable rates
of nitrification, the effect of biochar on nitrification was found to be minimal. In some cases,biochar additions to agricultural soils also decreased apparent ammonification rates (that is,
the breakdown of organic forms of nitrogen to ammonium) (DeLuca et al. 2009). Similarly,Granatstein et al. (2009) found that addition of biochar to soils led to a decrease in soil nitrate
production (nitrification) and a decrease in the amount of nitrogen available to plants.
atmosphericnitrogen
nitrogenertiliser
groundwater
manureplant
residuenitrogen gasnitrous oxide
ossil uelemissions
nitrite(NO
2-)
ammonium(NH+)
soil organicmatter
nitrate(NO
3-)
Nitrogen cycle9
Note: Nitrogen applied through fertiliser application or animal manure is converted to ammonium (ammonification). Ammonium is
oxidised to nitrite, which is converted to nitrate (nitrification) which is reduced to nitrous oxide or nitrogen gas (denitrification).
Nitrates are also taken up by plants and are converted to proteins (both plant and animal).
soil environment
N fixing bacterialightning fixation
denitrifcation
plantuptake
ammonifcation
nitrifcationnitrifcation
leaching
leachingrunoff
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
28/63
Biochar: implications or agricultural productivity ABARES technical report 11.6
20
DeLuca et al. (2009) also documents different experiments which show biochar decreasesnitrogen availability in tropical agricultural soils and that biochar increases nitrogen uptake
by plants. Biochar is thought to be able to bind ammonium ions from the soil solution,thereby reducing their concentrations in the soil solution (availability) and increasing their
concentration in biochar particles. Immobilisation of nitrogen on biochar should reducenitrogen losses from soil through leaching.
Nitrogen can also be lost from the soil through volatilisation of ammonia and through
denitrification in which nitrate is converted to nitrogen gas or the intermediates nitric oxideand nitrous oxide. Biochar is thought to reduce the potential for ammonia volatilisation,
because it decreases available ammonium in the soil solution and moderately raises the pHof soils; both conditions which do not favour ammonia formation and volatilisation. Also,
biochar is thought to be able to catalyse the reduction of nitrous oxide to nitrogen gas,thus completing denitrification and reducing the amount of nitrous oxidean important
greenhouse gasentering the atmosphere (box 1) (DeLuca et al. 2009; Van Zwieten et al. 2009).
Some biochars may also enhance biological nitrogen fixation by bacterial root nodules ofplants. Biological nitrogen fixation is very important in low input systems where nitrogen
fertiliser inputs are minimal, such as in developing countries. Biological nitrogen fixation is alsoimportant in terms of Australian crop rotations, where green manure crops (such as legume
crops) are used, and in the functioning of improved pastures. Rondon et al. (2007) foundthat biochar additions significantly increased biological nitrogen fixation by rhizobia at all
application rates (30, 60 and 90 grams per kilogram). They also noted that the improvements inbiological nitrogen fixation and biomass productivity were significantly greater compared with
normal productivity achieved by conventional fertiliser application (in the absence of biochar).
Rondon et al. (2007) therefore recommended that in-depth field studies be conducted toinvestigate this significant improvement in productivity. Free living nitrogen gas fixing bacteriaare ubiquitous in soils, but no studies show biochar application having a direct ef fect onnitrogen assimilation by this group of nitrogen-fixing organisms.
Phosphorus is another important plant nutrient. Microbial turnover and organic matter
decomposition regulate phosphorus mineralisation and hence its availability to plants. Severalstudies have demonstrated enhanced phosphorus uptake by plants in the presence of biochar,
but little work has been done on the underlying mechanism for this enhanced uptake. Themechanisms are likely to include biochar as a:
direct nutrient source of phosphorus
store of phosphorus bound to surface sites through its anion exchange capacity
modifier of soil pH, thereby modifying the pH-dependent solubility characteristics of
phosphorus compounds
promoter of microbial activity and phosphorus mineralisation (DeLuca et al. 2009).
Researchers suggest that biochar also improves the bioavailability of sulphur; an importantnutrient that depends on mineralisation of organic forms of sulphur to cycle through soils
(DeLuca et al. 2009).
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
29/63
Biochar: implications or agricultural productivity ABARES technical report 11.6
21
The overall nutrient impact of biochar additions to soils appears to increase the ability of thesoil to store or hold nutrients, rather than directly increasing nutrient content. This in turn is
expected to reduce the amount of nutrient loss through leaching.
Effects of biochar on plant growth
With the modification to soil characteristics described above, the effect of biochar additions to
soil on plant productivity is the most important outcome for its use in Australian agriculture.
Evidence gathered from both glasshouse and field trials indicates that biochar additions to
acidic and nutrient poor soils, combined with fertiliser application, can produce yields greaterthan either fertiliser or biochar alone. However, the effect of biochar on crop growth depends
on application rates and the soil type to which it is applied.
A key feature of biochar addition to soils is increased nitrogen use efficiency by plants. Theevidence suggests that significant reductions in nitrogen fertiliser application can be achieved
while maintaining similar yields, with the addition of biochar to soils. Alternatively, yields mayincrease significantly with the addition of biochar to soils and little change in established
nitrogen fertiliser regimes.
Glasshouse trialsChan et al. (2007) conducted a glasshouse pot test using radish grown in Australian soils
and found that adding herbaceous biochar (pH 9.4) at the rate of 100 tonnes per hectaresignificantly increased soil pH from 4.77 to 5.99, without affecting plant growth. However,
addition of both biochar and nitrogen fertiliser significantly affected soil pH and plantgrowth. At 100 tonnes per hectare application rate of biochar and nitrogen fertiliser, drymatter production was 266 per cent of the 100 tonnes per hectare biochar-without-nitrogen
treatment. When compared with untreated soil (no biochar and no fertiliser), dry matterproduction was 4.5 times greater when biochar and nitrogen were added. Despite this
biochar-induced increase in nitrogen use efficiency by plants at 100 tonnes per hectarebiochar, a yield depression at the rate of 10 tonnes per hectare biochar in both the nitrogen-
amended and no fertiliser treatments was evident.
In glasshouse trials using Australian soils Van Zwieten et al. (2010a) found an increase innitrogen use efficiency when wheat was grown with biochar and nitrogen fertilisation. In
this case, wheat yield was 30 per cent more with 2.2 per cent biochar application at the topfertiliser application rate, when compared with the same fertiliser rate and no biochar addition.
Radishes also showed improvements in nitrogen use efficiency, particularly at the lowerfertiliser application rates. For instance, radish biomass production at 17 kilograms nitrogen
per hectare and 2.2 per cent biochar was equivalent to biomass production at 88 kilogramsnitrogen per hectare alone.
In other glasshouse experiments, Van Zwieten et al. (2010b) found positive effects of biochar
and nitrogen fertilisation on the growth of wheat, soybean and radish in an initially acidic,nutrient-poor Australian ferrosol. Indeed, wheat growth was 2.5 times the no-biochar
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
30/63
Biochar: implications or agricultural productivity ABARES technical report 11.6
22
no-fertiliser control. However, when the same species were grown in a pH neutral andrelatively fertile soil, biochar in combination with added fertiliser caused a significant decrease
in growth for wheat and radish and had no effect on soybean growth. Only radishes increasedgrowth rates when biochar alone was added to this pH-neutral and fertile soil. These results
suggest the positive impacts of biochar would probably be greatest in acidic and nutrientpoor soils. Biochar additions to calcareous soils in southern Australia have recently produced
positive results (Krull pers. comm. 2011).
Field trialsField trials with biochar application have also shown increased yields of many plants; especiallywhere they are added with mineral fertilisers or with organic fertilisers, such as manure (Blackwell
et al. 2009). In tropical soils, above-ground biomass was shown to increase by 189 per cent when23 tonnes per hectare biochar was added to Columbian soils (Major et al. 2010a). Plant growth
was differentially stimulated; with legume biomass increasing almost 20 fold (1916 per centyield increase), while forb (herbaceous) and grass biomass increased to a lesser extent (292 and
93 per cent yield increase, respectively), compared with no biochar addition.
In adjacent field trials, the maize yield over the four years following biochar applicationwas higher in all but the year of application. In that year biochar addition showed no ef fect
(Major et al. 2010b). In the second, third and fourth years after 20 tonnes per hectare biocharapplication, maize yield increased by 28, 30 and 140 per cent respectively. At an application
rate of 8 tonnes per hectare, maize yields also increased in these years by 19, 15 and 71 per centrespectively. Japanese researchers also reported biochar-induced yield increases in the f ield for
sugarcane, rice and maize production in Japan, Laos and Indonesia (Asai et al. 2009; Chen et al.2010; Ogawa & Okimori 2010).
In the Australian context, several longer-term field trials are underway (Van Zwieten pers.comm. 2010). Solaiman et al. (2010) reported encouraging results from biochar application
to acidic soils with low cation exchange capacity in Western Australia. When using solublefertilisers at half the recommended rate (30 kilograms per hectare), addition of biochar at
6 tonnes per hectare resulted in a yield increase of 18 per cent. This treatment yielded500 kilograms per hectare more wheat than when using soluble fertiliser at the recommended
rate of 55 kilograms per hectare and biochar at 6 tonnes per hectare (Solaiman et al. 2010).
In an experiment with different planting densities and mineral fertiliser application, biocharapplications at 1.5, 3 and 6 tonnes per hectare resulted in significantly greater yields than when
biochar was not added (Solaiman et al. 2010). The yield increases in all biochar treatments wasapproximately 45 per cent compared with the control.
Van Zwieten et al. (2010c) reported extended benefits of biochar application over three
seasons in a maize-legume rotation in northern New South Wales. Papermill biochar applied at10 tonnes per hectare provided yields of 125 per cent in maize in 200708, 185 per cent in faba
beans in 2008 and 140 per cent in maize in 200809, when compared with the control. Withrespect to corn yields, paper mill biochar was more effective than poultry litter biochar, lime
or compost applications. Conversely, for faba beans, both biochars provided similar benefitswhich were lower than the yield increases with lime or compost addition.Table 6 summarises
the effects of biochar application on plant yield for a number of glasshouse and field trials.
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
31/63
Biochar: implications or agricultural productivity ABARES technical report 11.6
23
6
Summaryoselectedglass
houseandeldtrials
Location/soiltype
Cropgrown
Treatment
Yieldefect
R
eerence
Glassh
ousetrialon
yellow
orthictenosolsoil
Wheat(Triticu
m
aestivumL.)a
ndradish
(RaphanussativusL.)
Biochar:0,5,10,
20,5
0tha-1(
whole
treeresidue)andNitrogen:0,17,44,
88,
177kgha-1
Wheat:biomassincreasedwithincreasing
nitrogenapp
licationrates,upto20tonnes
perhectareb
iocharaddition
VanZwietenet
al.2010a
Wheat:negativeyieldresponsewith
biocharapplicationratesgreaterthan
10tha-1a
nd
177kgnitrogen
Wheat:~215%yieldincreasewiththe
applicationo
f177kgnitrogenand
10tha-1b
ioc
har
Radish:underallbiocharrates,radish
biomassincreasedwithincreasingnitrogen
Glassh
ousetrialonclay
loamsoil
Maize(Zeam
aysL)
Biochar:0,1and5%oftotalsoilmass
(miscanthus,willow,pine)producedat
either500oCfor10m
in,400oCfor10
minor600oCfor60m
in
Biochar(400oCfor10minutes):~23%yield
reduction
Biochar(600oCfor60minutes):165%yield
increaseat5%inclusionrate
Kwapinskietal.
2010
Biochar(500oCfor10min):upto437%
yieldincrease
at5%inclusionrate
Glassh
ousetrialon
FerrosolsoilfromN
ew
South
Wales,Australia
Radish(Raphanus
sativus),wheat(Triticum
aestivum)and
soybean
(Sorghumb
icolour)
Biochar:0,10tha-1(p
apermillwaste)
and
fertiliser(1.25gcontrolledrelease
fertiliser)
Wheat:bioch
ar+fertiliser=250%
Wheat:bioch
ar=nodifferenceinplant
growth
Soybean:biochar=nodifferenceinplant
growth
VanZwietenet
al.2010b
Radish:bioch
ar=~150%yieldincrease
Radish:bioch
ar+fertiliser=~170%yield
increase
continued...
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
32/63
Biochar: implications or agricultural productivity ABARES technical report 11.6
24
6
Summaryoselectedgla
sshouseandeldtrials
continued
Location/soiltype
Cropgrown
Treatment
Yieldefect
Reerence
Glasshousetrialon
loamycalcarosolsoil
fromV
ictoria,
Australia
Radish(Raph
anus
sativus),whe
at(Triticum
aestivum)an
dsoybean
(Sorghumbi
colour)
Biochar:0,10tha-1(papermillwaste)
and
fertiliser(1.25gco
ntrolledrelease
fertiliser)
Wheat:biochar=~50%yieldreduction
Wheat:biochar+fertiliser=~45%yield
reduction
Soybean:biochar=nodifferenceinplant
growth
V
anZwietenet
a
l.2010b
Radish:biochar=~325%yieldincrease
Radishbioch
ar+fertiliser=~60%yield
reduction
Colom
biansavanna
Oxiso
lsoil
Grasses,forb
sand
legumes
Biochar:0,
23.2tha-1(
pruningsofold
mangotrees)
189%yieldincrease(2.4-4.5tha-1a
dditional
drybiomass
)
M
ajoretal.
2
010a
Colom
biansavanna
Oxiso
lsoil
Maize(Zeam
aysL.)
Biochar:0,
20tha-1(woodbiochar)
Firstyear:no
significanteffect
Secondyear
:28%yieldincrease
M
ajoretal.
2
010b
Thirdyear:3
0%yieldincrease
Fourthyear:
140%yieldincrease
Shimajirimaji,
heavyclay
soil,J
apan
Sugarcane
Biochar:0,
3%(baga
sse)
106%yieldincrease(56kgha-1a
dditional
crop)
C
henetal.2010
continued...
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
33/63
Biochar: implications or agricultural productivity ABARES technical report 11.6
25
6
Summaryoselectedglas
shouseandeldtrials
continued
Location/soiltype
Cropgrown
Treatment
Yieldefect
Re
erence
Shimajirimaji,
heavyclay
soil,Japan
Sugarcane
Biochar:0,1%(biosolidsfrom
agriculturalsewerage
)
120%yieldincrease(189kgha-1a
dditional
crop)
Ch
enetal.2010
Sandyclayloams
oil,
Wester
nAustralia
Wheat(Triticum
aestivumL.va
r.Bonnie
rock)
Biochar:0,1.5,
3.0and
6tha-1(
oil
mallee)andnitrogen:0,
30,55,100kg
ha-1
Biochar(6tha-1)+fertiliser(30kgha-1):
18%yieldincrease(340kgha-1m
ore
wheat)
So
laimanetal.
20
10
Chromosolsoil,
New
SouthWales,Australia
Radish(Rapha
nus
sativusvar.LongScarlet)
Biochar:0,10,50and
100tha-1(
green
wasteincludinggrass
clippings,cotton
trashandplantprunings)andnitrogen:
0,100kgha-1
Biocharalone:noeffectonyieldatany
inclusionrate
Biochar+fertiliser:higheryieldincreases
withincreasin
gratesofbiochar
Ch
anetal.2007
Biochar(10tha-1)fertiliser:reduceddry
matterproduction
Ferroso
lsoil,
NewSouth
Wales,
Australia
Sweetcorn
Biochar:0,10tha-1(p
oultrylitter)
Corn:120%yieldincrease
Va
nZwietenet
al.
2010c
Ferroso
lsoil,
NewSouth
Wales,
Australia
Sweetcorn
Biochar:0,10tha-1(p
apermillwaste)
Corn:140%yieldincrease
Va
nZwietenet
al.
2010c
-
8/2/2019 Biochar in Agricultural Productivity_Technical Report
34/63
Biochar: implications or agricultural productivity ABARES technical report 11.6
26
Improving livestock productivityIn addition to the potential of biochar for soil amelioration and crop productivity, it may also
have the potential to improve livestock growth rates, while decreasing nitrogen outputs.