bio 5sb - scanjet systems · the scanjet bio 5sb is a new type of rotary spray head (rsh) tank...
TRANSCRIPT
Bio 5SB Scanjet tank cleaning equipment
78-01
KEY FEATURES
+ Rotating spray
+ 360° cleaning pattern
+ Ideal for small tanks
+ Low pressure
+ Low use of cleaning medium
The Scanjet Bio 5SB is a new type of Rotary Spray Head (RSH) tank cleaning
device. Compared with conventional static devices, the Bio 5SB is very efficient,
saving water and chemicals while improving cleaning effectiveness. The Bio 5SB
employs a unique fluid bearing rotary mechanism, with a service life two to three
times that of traditional ball bearing rotary devices.
The choice of either a clip-on (pin), weld-on or threaded connection means the Bio
5SB is always easy to install, whether building a new CIP tank cleaning system or
upgrading an existing one based on ordinary static or rotary spray devices.
With 360° impact coverage, self-cleaning and self-draining features, the Bio 5SB
design follows EHEDG and GMP guidelines, and can be supplied with EN10204-2.1,
2.2 or 3.1 material and FDA 21CFR compliance certificates. The Bio 5SB-XXX-A
clip-on and weld-on versions have attained 3A certification under sanitary standard
78-01. Surface finish roughness supplied as standard is Ra = 0.8 μm (30 μ inch);
other surfaces are available upon request.
The Bio 5SB can be used in conjunction with the Scanjet WASHTRAC sensor to
monitor and verify its operation and performance.
The Bio 5SB is the first choice for anyone looking for the most advanced Rotary
Spray Head tank cleaning device available.
The Scanjet Bio 5SB Rotary Spray Head can be used in a wide range of
applications, including:
+ Mixing vessels
+ Blending tanks
+ Beverage tanks
+ Dairy tanks
+ Yeast tanks
+ Reactors
+ IBCs
1 1,5 2 2,5 3 3,5 4 4,5 5
0
2
4
6
8
10
20 30 40 50 60 700
5
10
15
20
25
30
35
40
Flow vs. Pressure
bar
psi
m3/h USgpm
1 1,5 2 2,5 3 3,5 4 4,5 5
0
1
2
3
4
0,5
1,5
2,5
3,5
Impact cleaning
20 30 40 50 60 70
0
1
2
3
4
5
6
7
8
9
10
11
12
13
m ft
bar
psi
Cleaning Radius
Wetting
360º SPRAY PATTERN
Ø 25.3/ 28.3(OD) (1/1.11 in)Ø 25.6/28.6(OD) (1/1.12 in)
PINCONNECTION
¾" BSPf¾" NPTf
THREADCONNECTION
Ø 25/22.5(ID) (0.98/0.89 in)
75
(2.9
5 in
)
Ø 45 (1.78 in)
WELDCONNECTION
¾" BSP¾" NPT
THREADCONNECTION
25/22,5(OD)
45
75
WELDCONNECTION
25,6/ 28,6(ID/OD)25,3/28,3(ID/OD)
PINCONNECTION
360º SPRAY PATTERN
* Clip-on models have approx. 0,5 m³/h higher flow rate
Technical performance Dimensions
Specifications
Flow* 4.1-9.8 m³/h (18-43 USgpm)
Inlet pressure 1-5 bar (14-72 psi)
Max pressure 5 bar (72 psi)
Recommended pressure 3 bar (43 psi)
Max working temperature 95°C (200°F)
Max ambient temperature 150°C (300°F)
Weight 137-175 g (4.83-6.17 oz)
Connections ¾” NPT or BSP
Weld connection
Pin connection
Material EN1.4404/PEEK
Lubrication Self lubricated by media
Pressure/Flow
Cleaning radius
Scanjet Systems AB P.O. Box 9316 SE-400 97 Göteborg SwedenPhone + 46 31 3387530 Fax + 46 31 3387540 E-mail [email protected] www.scanjetsystems.com
* Because of variations in part wear, water temperature, installation etc., the flow may differ ±10% from specified value.Continuous product improvement is the policy of Scanjet Group and we reserve the right to alter the specifications at any time without prior notice. Errors and omissions excepted.All trademarks, designs and other intellectual property depicted here are property of the Scanjet Group unless otherwise stated, and may be registered, patented or otherwise protected in certain jurisdictions.Copyright © Scanjet Group. All rights reserved.