bimetal thermometersmy.korcham.net/bbs_new2/files/temperature-tb series.pdf · 2008-02-21 ·...
TRANSCRIPT
Bimetal Thermometers
Bimetal thermometers use two metals with different temperature expansion coefficients wound in a helical shape and indicate the temperature by transmitting the deflection of the metal by temperature change to a pointer.
・Error due to ambient temperature is smaller than that of the filled type. ・Since there is no filled liquid, it is safe. (No pollution) ・Construction is simple and it is cheap.
Select the temperature range so that the thermometer is always within the 30 to 60% range of the scale span, when selecting the thermometer. Check whether the described wetted parts material conforms to the gas/liquid to be measured or not.
Cat. No.D03-01-F
Manufacturing temperature range: -50 ~ 500 ℃ Size: 75 DIA., 100 DIA., 150 DIA. (Small thermometer 60 DIA.) Shape: T type I type Tilt capabilities type Temperature sensor/connection material: SUS304
Fig.1 Basic of the bimetal (1) the initial state (2) the state after the temperature changed Fig.2 Bimetal for the thermometer Helical
Principle/Construction: (1) (2) Fig. 1 Fig. 2 Thermometer A displacement of the bimetal is transmitted to the pointer ■TB 1 type (T type) ■TB 2 type (I type)
OUTLINE
FEATURES
SPECIFICATIONS
Cover
Gasket
Window
Gasket
Leave pointer
Leave pointer
Pointer scale
Pointer scale
Connection
Bulb
Case
Bimetal
Connection
Bulb
Bimetal
FOR THE SELECTION OF THE BIMETAL THERMOMETER SPECIFICATION
2.Shape in the thermometer temperature sensor
Union type
Slide type
・Standard specification
Since it is fastened to the mounting screw by tightening a set screw, the position of the temperature sensor does not change.
Maximum allowable working pressure of union type is Under 200℃ → 2MPa 200℃ or over → 1MPa (When the above is over, a well is necessary.)
Temperature sensorMounting screwSet screw
Gasket
Construction tightens the gasket with a set screw and the temperature sensor can be fastened at an arbitrary position.
Maximum working pressure of the slide is 0.3MPa (When the above is over, a well is necessary.)
Temperature sensorMounting screwSet screw
・When the position of the measurement fluid in a tank, etc. changes and the position of the temperature sensor must be adjusted ・When a well is installed and when you want to insert the temperature sensor down to the bottom
3.Temperature sensor minimum insertion dimension ・The minimum insertion dimension is determined by the type, temperature range, and temperature sensor diameter. If the temperature sensor is not completely inserted into the measurement liquid up to this dimension, since performance cannot be secured, select the best dimension above this minimum insertion dimension.
4.Required conditions of a well (Thermowell) (1) When there is the danger that the measured fluid may corrode the temperature sensor, a well made of material suitable for the measurement fluid is necessary. (2) When high pressure is applied to the temperature sensor, a well suitable for the working pressure is necessary. (3) When the measurement fluid flows, a well suitable for the flow rate is necessary. (4) When the measurement fluid leaks when the thermometer is removed, the use of a well is convenient at maintenance. (5) Necessary when the filled liquid of the thermometer body should leak and when the measurement liquid may be contaminated.
Good Bad
(1) (2) (3) (4) (5)
Danger of corrosion High pressure applied There is a flow Thermometer removal Filled liquid leakage
Bimetal Thermometers
1.Temperature range (Scale range) ・Select the scale range so that the temperature range is always within the 30 to 60% range of the scale span. ・The thermometer starts temperature measurement from the time of manufacture and the instrument itself is active even when not in use. ・When a temperature above the scale range is applied to the thermometer, there is the danger that the thermometer may be damaged. For example, when there is the danger that the thermometer may cross the equator or through a cold region during shipment and the temperature range may be exceeded, caution is necessary.
Working range
Minimum insertion length
Minimum insertion length
2
BIMETAL THERMOMETERS LIST
Bimetal Thermometers
1.Drip-proof bimetal thermometers
Type Shape Manufacturing temperature range Size
75 DIA.(3″)
75 DIA.(3″)
100 DIA.(4″)
100 DIA.(4″)
150 DIA.(6″)
150 DIA.(6″)
Model
TB13
TB14
TB16
TB23
TB24
TB26
Case drip-proof construction
Protection class IP43
T type
I type
-50 ~ 50 ℃
↓
0 ~ 500 ℃
2.Bimetal thermometer made of stainless steel case (rain-proof type)
Type Shape Manufacturing temperature range Size
75 DIA.(3″)
100 DIA.(4″)
100 DIA.(4″)
150 DIA.(6″)
150 DIA.(6″)
Model
RB43
RB44
RB46
RB14
RB16
Case rain-proof construction
Protection class IP65
T type
I type
-50 ~ 50 ℃
↓
0 ~ 500 ℃
4.Small bimetal thermometers (indoor)
Type Shape Manufacturing temperature range Size
60 DIA.
Model
TB12
TB22
TB32
T type
I type
V type
-50 ~ 50 ℃
↓
0 ~ 500 ℃
3.Tilt capabilities (rain-proof) bimetal thermometers
Shape Manufacturing temperature range Size
125 DIA.(5″)
100 DIA.(4″)
150 DIA.(6″)
Model
TB44
TB45
TB46
Case rain-proof construction
Protection class IP65-50 ~ 50 ℃
↓ 0 ~ 500 ℃
3
Bimetal Thermometers
CONNECTION/TEMPERATURE SENSOR SPECIFICATION 1
1. Without a well (Thermowell)
2.With a well (Thermowell)
Connection shapeScrew Flange
Union type
Slide type
Connection shapeScrew Flange
Union type
Standard
Double socket
Slide type
Union type
Slide type
Maximum working pressure is 2MPa under 200℃ 1MPa in 200℃ or over
Max. operating pressure 0.3MPa
(d = 8 dia. in the temperature sensor dia. 6 dia. and the Size 150 dia. is not available.)
(d = 8 dia. in the temperature sensor dia. 6 dia. and the Size 150 dia. is not available.)
d DIA.
L24
Set screw
d DIA.
34(10)
L
d DIA.Set screw
40d DIA.
(10)
d1 DIA.
L
Set screw
45(10)
(10) 40L
d1 DIA.Set screw
L
d1 DIA.Set screw
d1 DIA.
L
Set screw
45(10) (25)
45(10) (25)
(d = 8 dia. in the temperature sensor dia. 6 dia. and the Size 150 dia. is not available.)
Connection
Connection
W22 a lot 14
W22 a lot 14
W22 a lot 14
T
T
Gasket
T
JIS, ANSI, JPI
T
T
T
Connection R1/2 (PT) or 1/2NPT
Connection R1/2 (PT) or 1/2NPT
4
CONNECTION/TEMPERATURE SENSOR SPECIFICATION 2
Bimetal Thermometers
Connection dimension
Scale
● the scale angle is 270 ゚to 300 .゚
Ground: white Entry: black, however the scale in (-) and number is red.
Connection dimension for screw Connection dimension for flange
Standard
connection
Note
R1/2(PT),1/2NPT G1/2B(PF) R3/4(PT),G3/4B(PF) (Set screw only = W22 a lot 14)
The screw/flange except the above can also be manufactured, please contact NKS.
Scale range ℃
0~ 50
0~100
0~250
0~500
0~ 60
0~120
0~ 80
0~200
0~400
0~150
0~300
-10~ 50
-20~100
-30~ 50
-50~ 50
Scale division and number entry positionSize (○mark adjusts)60・75 100 150
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ - -
- ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ - -
- ○ ○
○ - -
- ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
0 10 20 30 40 50
0 50 100 150 200 250
0 20 40 60 80 100
0 100 200 300 400 500
0 10 20 30 40 6050
0 50 100 150 200 300250
0 50 100 150 200 300250
-10 0 10 20 30 5040
-20 0 20 40 60 10080
0 10 20 30 40 6050
0 20 40 60 80 120100
0 20 40 60 80
0 50 100 150 2000 100 200 300 400
0 30 60 90 120 150
0 30 60 90 120 150
-30 -20 -10 0 10 20 30 40 50
-50 -40 -20 0 20 40 50
[Example]
J I S 10 K 20 A R F J I S 10 K 25 A R F A N S I 1 B 150 R F A N S I 1 B 300 R F
40
20
0
60
80
100
5
Bimetal Thermometers
CONNECTION/TEMPERATURE SENSOR SPECIFICATION 3
■Connection shape and dimension
■Relationship between temperature sensor dia., connection shape and T (connection screw, connection flange)
●Without connection
●With connection
Note) refer to the JIS, ANSI, JPI, etc. for the flange dimension.
(mm)
T J
18
20
18
20
18
S
8
9.5
ー
ー
8
W
ー
ー
ー
32
36
X
27 x 31.2
30 x 34.6
32 x 37
36 x 41.6
27 x 31.2
R1/2(PT)
R3/4(PT)
G1/2B(PF)
G3/4B(PF)
1/2 NPT
Union type
Slide type
Union type
Slide type
Screw
Flange
d DIA.
85゜
2
9
2
24 L
19 DIA.
L base point
Set screw W22 a lot 14
ConnectionW22 a lot 14
19 DIA.
15 DIA.
90゜
10
3
d DIA.
S
J
(10) 34
X Hex. Set screw T
Taper
X Hex.
W DIA.
d DIA.
T Straight
J 3
34
d DIA.
S
J
(10) 40
X Hex. Set screw
T Taper
Gasket
X Hex.
W DIA.
d DIA.
T Straight
J 3
40
d DIA.
34(10)
40
d DIA.
(10)
Temperature sensor dia. (d)
Connection shape
Union type
○
○ 8 DIA.
6 DIA.
○
○
○
○
○
○
○
○
○
○
-
○
○ 10 DIA.
Slide typeConnection screw Connection flange
JIS,ANSI,JPI3/41/2
T
* 8 dia. slide type is available only in the 75 dia., 100 dia.. However, no tilt capabilities and small type can be manufactured.
*
6
DRIP-PROOF BIMETAL THERMOMETER 1
TB13 ・ 14 ・ 16 T type bimetal
■Dimensions
■Specifications
■Scale range, temperature sensor dia. and temperature sensor length
●When the minimum insertion dimension in ( ) for 8 dia. and 10 dia. temperature sensors is used, please specify NKS. ●The minimum insertion dimension above is the dimension when there is no well. When there is a well, this dimension plus 25mm becomes the necessary minimum insertion dimension. ●The dimensions of this table are the maximum length the temperature sensor is inserted into the measurement liquid. ●When indicating the dimensions of the temperature sensor, please indicate the L dimension on this value is 5mm increments.
Manufacturing temperature range -50 ~ 50 ℃→ 0 ~ 500℃
Construction: drip-proof, IP43 equivalent, Material: TB13/14 = ADC12, TB16 = AC7, finish: black
Temperature sensor: SUS304, Connection screw/flange: SUS304
Within ±2%F.S.
R1/2 (PT), R3/4 (PT), 1/2NPT,G1/2B (PF), G3/4B (PF)
JIS10K20ARF, JIS10K25ARF, ANSI1B150RF, ANSI1B300RF
Union type, Slide type 6 dia. and 8 dia. in the TB16 are not available in the slide type.
When the maximum range exceeds 400℃ or over,
the slide type cannot be manufactured.
Double socket union: R1/2, 1/2NPT (connection)
Double socket slide: R1/2, 1/2NPT (connection)
6, 8, 10
12, 15 (The temperature sensor 6 dia. with a well cannot be manufactured.)
Without a well
With a well
Temperature sensor(d)
Well (d1)
Case
Wetted parts material
Accuracy
Standard connection screw
Standard connection flange
Connection shape
Temperature dia. (DIA.)
Scale range ℃
Minimum scale ℃
Standard Temperature sensor dia. X length (d) x (L) mm
Temperature sensor length (L) mm
Minimum insertion requisite dimension
d = 6 DIA.
-50~ 50 2 10DIA.×100 105 140( 85) 100( 65)
120( 85)
90( 65)
145( 95)
165(110)
145( 95)
120( 85)
100( 65)
90( 65)
80( 55)
70( 50)
110( 65)
100( 60)
80( 55)
75( 50)
140( 85)
120( 80)
120( 80)
150( 85)
130( 75)
110( 70)
95( 60)
105( 65)
90( 55)
165(110)
165(110)
205(120)
205(120)
240(140)
125
160
185
160
125
105
95
80
65
110
95
85
75
95
×150
×100
×150
×200
×150
×150
×100
×100
×100
×100
×150
×100
×100
×100
2
2
1
1
1 (2)*
2
2
2
2 (5)*
5
5
5 (10)*
10
10
-30~ 50
-20~100
-10~ 50
0~ 50
~ 60
~ 80
~100
~120
~150
~200
~250
~300
~400
~500
d = 8 DIA. d = 10 DIA.Maximum
Until 300 by the temperature sensor dia. 6 dia.( )
500
*The number ( ) in the minimum scale is for TB13.
Bimetal Thermometers
Model
TB13
TB14
TB16
Size
75(3″)
100(4″)
150(6″)
D
96
122
172
Weight (L=150)
approx. 380g
approx. 480g
approx. 710g
T
79
15
(6)
L
d DIA.
D DIA.
29
7
Bimetal Thermometers
DRIP-PROOF BIMETAL THERMOMETER 2
TB23 ・ 24 ・ 26 I type bimetal
■Dimensions
■Specifications
■Scale range, temperature sensor dia. and temperature sensor length
●When the minimum insertion dimension in ( ) for 8 dia. and 10 dia. temperature sensors is used, please specify NKS. ●The minimum insertion dimension above is the dimension when there is no well. When there is a well, this dimension plus 25mm becomes the necessary minimum insertion dimension. ●The dimensions of this table are the maximum length the temperature sensor is inserted into the measurement liquid. ●When indicating the dimensions of the temperature sensor, please indicate the L dimension on this value is 5mm increments.
Model
TB23
TB24
TB26
Size
75(3〃) 96
122
172
100(4〃)
150(6〃)
D H
46
58
58
Weight (L=150)
approx. 450g
approx. 540g
approx. 720g
Manufacturing temperature range - 50 ~ 50 ℃ → 0 ~ 500 ℃
Construction: drip-proof, IP43 equivalent, Material: TB23/24 = ADC12, TB26 = AC7A, finish: black
Temperature sensor: SUS304, Connection screw/flange: SUS304
Within ±2%F.S.
R1/2 (PT), R3/4 (PT), 1/2NPT, G1/2B (PF), G3/4B (PF )
JIS10K20ARF, JIS10K25ARF, ANSI1B150RF, ANSI1B300RF
Union type, Slide type 6 dia. and 8 dia. in the TB26 are not available in the slide type.
When the maximum range exceeds 400℃ or over,
the slide type cannot be manufactured.
Double socket union: R1/2, 1/2NPT (connection)
Double socket slide: R1/2, 1/2NPT (connection)
6, 8, 10
12, 15 (The temperature sensor 6 dia. with a well cannot be manufactured.)
Without a well
With a well
Temperature sensor (d)
Well (d1)
Case
Wetted parts material
Accuracy
Standard connection screw
Standard connection flange
Connection shape
Temperature dia. (DIA.)
Scale range ℃
Minimum scale ℃
Standard Temperature sensor dia. X length (d) x (L) mm
Temperature sensor length (L) mm
Minimum insertion requisite dimension
d= 6 DIA.
-50~ 50 2 10DIA.×100 105 140( 85) 100( 65)
120( 85)
90( 65)
145( 95)
165(110)
145( 95)
120( 85)
100( 65)
90( 65)
80( 55)
70( 50)
110( 65)
100( 60)
80( 55)
75( 50)
140( 85)
120( 80)
120( 80)
150( 85)
130( 75)
110( 70)
95( 60)
105( 65)
90( 55)
165(110)
165(110)
205(120)
205(120)
240(140)
125
160
185
160
125
105
95
80
65
110
95
85
75
95
×150
×100
×150
×200
×150
×150
×100
×100
×100
×100
×150
×100
×100
×100
2
2
1
1
1 (2)*
2
2
2
2 (5)*
5
5
5 (10)*
10
10
-30~ 50
-20~100
-10~ 50
0~ 50
~ 60
~ 80
~100
~120
~150
~200
~250
~300
~400
~500
d= 8 DIA. d= 10 DIA.Maximum
Until 300 by the temperature sensor dia. 6 dia.( )
500
*The number ( ) in the minimum scale is for TB23.
T
1541
59
H
(6)
50L
D DIA.
d DIA.
8
Model number configuration For ordering, please specify the model number, each specs and range.
T B① Bimetal Thermometers
Model name
② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪ ⑫ ⑬ ⑭ ⑮
Selective spec.Model number Additional spec. (Option)
Type 3 75 DIA.
3 75 DIA.
4 100 DIA.
4 100 DIA.
6 150 DIA.
6
1
2
1
2
1
2 150 DIA.
T type
I type
T type
I type
T type
I type
Drip-proof
Drip-proof
Drip-proof
Drip-proof
Drip-proof
Drip-proof
0
Welded type Boring type
Straight Taper
Welded type
General product for flange
SW11(SW10) SW41(SW40) SW71(SW70) SW81
SW12
SW13
SW14
SW15
SW42
SW43
SW44
SW45
SW72
SW73
SW74
SW75
SW82
―
―
―
Without well
Screw in a well①
With well
1 Inside screw: Standard (W22 a lot 14)
2 Inside screw: Rc1/2 Double socket
3 Inside screw: 1/2NPT Double socket
4 Inside screw: G1/2 Double socket
Connection part
②
5 Inside screw: Rc3/4 Double socket
0 Union type/Non-removable type
1 Slide type/Non-removable type (When the maximum range at temperature sensor 8 dia. in the 150 dia. exceeds 400℃ or over, the slide type/non-removable type cannot be manufactured.)
0 R1/2
Connection screws
③ 1 R3/4
2 1/2NPT
3 G1/2B
4 G3/4B
5 JIS10K20ARF
6 JIS10K25ARF
7 ANSI1B150RF
8 ANSI1B300RF
A Set screw only (W22 a lot 14)
B R3/8
C R1
D 3/4NPT
E 1NPT
F JIS10K15ARF
G JIS10K40ARF
H JIS10K50ARF
J JIS20K20ARF
K JIS20K25ARF
L JIS10K15AFF
M JIS10K20AFF
N JIS10K25AFF
P ANSI3/4B150RF
Q ANSI3/4B300RF
R ANSI1B600RF
S ANSI 1 1/2B150RF
T ANSI 1 1/2B300RF
U ANSI 1 1/2B600RF
W JPI 1B150RF
X JPI 1B300RF
Y JPI 1B600RF
Z Input type
1 0 ~ 50, 60, 80, 100, 120, 150, 200, 250, 300
Range ℃ ④
2 0 ~ 400, 500
3 -10 ~ 50, -20 ~ 100, -30 ~ 50, -50 ~ 50
1 SUS304
Temperature sensor material
⑤ 2 SUS316
X In case with a well
0 d=6 dia.
Temperature sensor dia.
⑥ 1 d=8 dia.
2 d=10 dia.
L=300 (max.) Non available with a well
L=500 (max.)
L=500 (max.)
X In case with a well
[Manufacturing range] ・Temperature sensor 6 dia. and 8 dia. of TB16, TB26 in the slide type is not available. ・Temperature sensor 6 dia. with a well cannot be manufactured. ・Well: when the maximum range at TB16 for the slide and temperature sensor 8 dia. in TB26 exceeds 400℃ or over, cannot be manufactured.
Minimum dimension ~500mm
Temperature sensor length (mm) L dimension
⑦ X
A
In case with a well
1 Welded
Type of well⑬
4 Boring type straight
7 Boring type taper
8 Welded general product for flange
0 For slide
Screw within well
⑭ 1 W22 a lot 14
2 Rc1/2
3 1/2NPT
4 G1/2
5 Rc3/4
6 3/4NPT
7 G3/4
General products: Not available
General products: Not available
General products: Not available
General products: Not available
General products: Not available
General products: Not available
0 Nil
Documents⑮
1 Required (Please specify the desired documents separately.) Submission drawings, instruction manual, inspection procedure, mill sheet, test report (1 pc 1 copy), traceability certificate, inspection certificate, dialstrength calculation, attended inspection
Specify the well model number. in another page.
*When ordering, please specify the temperature sensor and lead tracks length. *The model construction of well is SW ⑬⑭. *In case with a well, please specify SW type No. after the well [thermowell] manufacturing specifications at the P 14 to is referred.□
Bimetal Thermometers
Specify "X" if there is no specification item.
(When ordering, please specify the range and units separately.)
9
Bimetal Thermometers
BIMETAL THERMOMETER MADE OF STAINLESS STEEL CASE: RAIN-PROOF TYPE 1
RB43 ・ 44 ・ 46 T type bimetal
■Dimensions
T
D DIA.
57(11) ab
■Specifications
■Scale range, temperature sensor dia. and temperature sensor length
●When the minimum insertion dimension in ( ) for 8 dia. and 10 dia. temperature sensors is used, please specify NKS. ●The minimum insertion dimension above is the dimension when there is no well. When there is a well, this dimension plus 25mm becomes the necessary minimum insertion dimension. ●The dimensions of this table are the maximum length the temperature sensor is inserted into the measurement liquid. ●When indicating the dimensions of the temperature sensor, please indicate the L dimension on this value is 5mm increments.
Model
RB43
RB44
RB46
Size
75(3〃) 89
116
171
100(4〃)
150(6〃)
D a
18
17
22
b
28
27
32
Weight (L=200)
Approx. 300g
Approx. 400g
Approx.1000g
Manufacturing temperature range -50 ~ 50 ℃ → 0 ~ 500 ℃
Construction: rain-proof, IP65 equivalent, material: SUS304
Temperature sensor: SUS304, Connection screw/flange: SUS304
Within ±2%F.S. and ±1%F.S. (RB44: range -50 ~ 50 ℃ → 0 ~ 300 ℃)
R1/2 (PT), R3/4 (PT), 1/2NPT, G1/2B (PF), G3/4B (PF)
JIS10K20ARF, JIS10K25ARF, ANSI1B150RF, ANSI1B300RF
Union type, Slide type 6 dia. and 8 dia. in the RB46 are not available in the slide type.
When the maximum range exceeds 400℃ or over,
the slide type cannot be manufactured.
Double socket union: R1/2, 1/2NPT (connection)
Double socket slide: R1/2, 1/2NPT (connection)
6, 8, 10
12, 15 (The temperature sensor 6 dia. with a well cannot be manufactured.)
Without a well
With a well
Temperature sensor(d)
Well (d1)
Case
Wetted parts material
Accuracy
Standard connection screw
Standard connection flange
Connection shape
Temperature dia. (DIA.)
Scale range ℃
Minimum scale ℃
Standard Temperature sensor dia. X length (d) x (L) mm
Temperature sensor length (L) mm
Minimum insertion requisite dimension
d= 6 DIA.
-50~ 50 2 10DIA.×100 105 140( 85) 100( 65)
120( 85)
90( 65)
145( 95)
165(110)
145( 95)
120( 85)
100( 65)
90( 65)
80( 55)
70( 50)
110( 65)
100( 60)
80( 55)
75( 50)
140( 85)
120( 80)
120( 80)
150( 85)
130( 75)
110( 70)
95( 60)
105( 65)
90( 55)
165(110)
165(110)
205(120)
205(120)
240(140)
125
160
185
160
125
105
95
80
65
110
95
85
75
95
×150
×100
×150
×200
×150
×150
×100
×100
×100
×100
×150
×100
×100
×100
2
2
1
1
1 (2)*
2
2
2
2 (5)*
5
5
5 (10)*
10
10
-30~ 50
-20~100
-10~ 50
0~ 50
~ 60
~ 80
~100
~120
~150
~200
~250
~300
~400
~500
d= 8 DIA. d= 10 DIA.Maximum
Until 300 by the temperature sensor dia. 6 dia.( )
500
*The number ( ) in the minimum scale is for RB43.
10
BIMETAL THERMOMETER MADE OF STAINLESS STEEL CASE: RAIN-PROOF TYPE 2
RB14 ・ 16 I type bimetal
■Dimensions
■Specifications
■Scale range, temperature sensor dia. and temperature sensor length
●When the minimum insertion dimension in ( ) for 8 dia. and 10 dia. temperature sensors is used, please specify NKS. ●The minimum insertion dimension above is the dimension when there is no well. When there is a well, this dimension plus 25mm becomes the necessary minimum insertion dimension. ●The dimensions of this table are the maximum length the temperature sensor is inserted into the measurement liquid. ●When indicating the dimensions of the temperature sensor, please indicate the L dimension on this value is 5mm increments.
Manufacturing temperature range -50 ~ 50 ℃ → 0 ~ 500 ℃
Construction: rain-proof, IP65 equivalent, material: SUS304
Temperature sensor: SUS304, Connection screw/flange: SUS304
Within ±2%F.S. and ±1%F.S. (RB14: -50 ~ 50 ℃ → 0 ~ 300 ℃)
R1/2 (PT), R3/4(PT), 1/2NPT, G1/2B (PF), G3/4B (PF)
JIS10K20ARF, JIS10K25ARF, ANSI1B150RF, ANSI1B300RF
Union type, Slide type 6 dia. and 8 dia. in the RB16 are not available in the slide type.
When the maximum range exceeds 400℃ or over,
the slide type cannot be manufactured.
Double socket union: R1/2, 1/2NPT (connection)
Double socket slide: R1/2, 1/2NPT (connection)
6, 8, 10
12, 15 (The temperature sensor 6 dia. with a well cannot be manufactured.)
Without a well
With a well
Temperature sensor(d)
Well (d1)
Case
Wetted parts material
Accuracy
Standard connection screw
Standard connection flange
Connection shape
Temperature dia. (DIA.)
Scale range ℃
Minimum scale ℃
Standard Temperature sensor dia. X length (d) x (L) mm
Temperature sensor length (L) mm
Minimum insertion requisite dimension
d= 6 DIA.
-50~ 50 2 10DIA.×100 105 140( 85) 100( 65)
120( 85)
90( 65)
145( 95)
165(110)
145( 95)
120( 85)
100( 65)
90( 65)
80( 55)
70( 50)
110( 65)
100( 60)
80( 55)
75( 50)
140( 85)
120( 80)
120( 80)
150( 85)
130( 75)
110( 70)
95( 60)
105( 65)
90( 55)
165(110)
165(110)
205(120)
205(120)
240(140)
125
160
185
160
125
105
95
80
65
110
95
85
75
95
×150
×100
×150
×200
×150
×150
×100
×100
×100
×100
×150
×100
×100
×100
2
2
1
1
1
2
2
2
2
5
5
5
10
10
-30~ 50
-20~100
-10~ 50
0~ 50
~ 60
~ 80
~100
~120
~150
~200
~250
~300
~400
~500
d= 8 DIA. d= 10 DIA.Maximum
Until 300 by the temperature sensor dia. 6 dia.( )
500
Bimetal Thermometers
Model
RB14
RB16
Size
100(4″)
150(6″)
D a b
116 55 17
171 59 21
H
56
85
Weight (L=200)
Approx. 550g
Approx.1300g
D DIA.
H(11)
57
a
b
11
Model number configuration For ordering, please specify the model number, each specs and range.
R B① Bimetal Thermometers
Model name
② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪ ⑫ ⑬ ⑭ ⑮
Selective spec.Model number Additional spec. (Option)
Type 3 75 DIA.
4 100 DIA.
4 100 DIA.
6 150 DIA.
6
4
1
4
1
4 150 DIA.
T type
I type
T type
I type
T type
Rain-proof
Rain-proof
Rain-proof
Rain-proof
Rain-proof
0
Welded type Boring type
Straight Taper
Welded type
General product for flange
SW11(SW10) SW41(SW40) SW71(SW70) SW81
SW12
SW13
SW14
SW15
SW42
SW43
SW44
SW45
SW72
SW73
SW74
SW75
SW82
―
―
―
Without well
Screw in a well①
With well
1 Inside screw: Standard (W22 a lot 14)
2 Inside screw: Rc1/2 Double socket
3 Inside screw: 1/2NPT Double socket
4 Inside screw: G1/2 Double socket
Connection part
②
5 Inside screw: Rc3/4 Double socket
0 Union type
1 Slide type (When the maximum range at temperature sensor 6 dia. and 8 dia., 10 dia. in the RB16 exceeds 400℃ or over, the slide type cannot be manufactured.)
0 R1/2
Connection screws
③ 1 R3/4
2 1/2NPT
3 G1/2B
4 G3/4B
5 JIS10K20ARF
6 JIS10K25ARF
7 ANSI1B150RF
8 ANSI1B300RF
A Set screw only (W22 a lot 14)
B R3/8
C R1
D 3/4NPT
E 1NPT
F JIS10K15ARF
G JIS10K40ARF
H JIS10K50ARF
J JIS20K20ARF
K JIS20K25ARF
L JIS10K15AFF
M JIS10K20AFF
N JIS10K25AFF
P ANSI3/4B150RF
Q ANSI3/4B300RF
R ANSI1B600RF
S ANSI 1 1/2B150RF
T ANSI 1 1/2B300RF
U ANSI 1 1/2B600RF
W JPI 1B150RF
X JPI 1B300RF
Y JPI 1B600RF
1 0 ~ 50, 60, 80, 100, 120, 150, 200, 250, 300
Range ℃ ④
2 0 ~ 400, 500
3 -10 ~ 50, -20 ~ 100, -30 ~ 50, -50 ~ 50
1 SUS304
Temperature sensor material
⑤ 2 SUS316
X In case with a well
0 d=6 dia.
Temperature sensor dia.
⑥ 1 d=8 dia.
2 d=10 dia.
L=300 (max.) Non available with a well
L=500 (max.)
L=500 (max.)
X In case with a well
[Manufacturing range] ・Temperature sensor 6 dia. with a well is not available. *1 8 dia., 10 dia. in the RB16 cannot be manufactured.
Minimum dimension ~500mm
Temperature sensor length (mm) L dimension
⑦ X
A
In case with a well
1 Welded
Type of well⑬
4 Boring type straight
7 Boring type taper
8 Welded general product for flange
0 For slide*1
Screw within well
⑭ 1 W22 a lot 14
2 Rc1/2
3 1/2NPT
4 G1/2
5 Rc3/4
6 3/4NPT
7 G3/4
General products: Not available
General products: Not available
General products: Not available
General products: Not available
General products: Not available
General products: Not available
0 Nil
Documents⑮
1 Required (Please specify the desired documents separately.) Submission drawings, instruction manual, inspection procedure, mill sheet, test report (1 pc 1 copy), traceability certificate, inspection certificate, dialstrength calculation, attended inspection
Specify the well model number. in another page.
*When ordering, please specify the temperature sensor and lead tracks length. *The model construction of well is SW ⑬⑭. *In case with a well, please specify SW type No. after the well [thermowell] manufacturing specifications at the P 14 to is referred.□
Bimetal Thermometers
Specify "X" if there is no specification item.
(When ordering, please specify the range and units separately.)
12
TILT CAPABILITIES/BIMETAL THERMOMETER: RAIN-PROOF
TB44 ・ 45 ・ 46 Tilt capabilities bimetal type
■Specifications
■Scale range, temperature sensor dia. and temperature sensor length
●The minimum insertion dimension above is the dimension when there is no well. When there is a well, this dimension plus 25mm becomes the necessary minimum insertion dimension. ●The dimensions of this table are the maximum length the temperature sensor is inserted into the measurement liquid. ●When indicating the dimensions of the temperature sensor, please indicate the L dimension on this value is 5mm increments.
Manufacturing temperature range -50 ~ 50 ℃ → 0 ~ 500 ℃
Construction: rain-proof, IP65 equivalent, material: SUS304
Temperature sensor: SUS304, Connection screw/flange: SUS304
Within ±2%F.S.
R1/2 (PT), R3/4 (PT), 1/2NPT, G1/2B (PF), G3/4B (PF)
JIS10K20ARF, JIS10K25ARF, ANSI1B150RF, ANSI1B300RF
TB46 (150 dia.) is only available.
Union type (the slide type is not available.)
Double socket union type: R1/2, 1/2NPT (Connection)
6, 8, 10
12, 15 (The temperature sensor 6 dia. with a well cannot be manufactured.)
Without a well
With a well
Temperature sensor(d)
Well (d1)
Case
Wetted parts material
Accuracy
Standard connection screw
Standard connection flange
External zero adjustment mechanism
Connection shape
Temperature dia. (DIA.)
Scale range ℃
Minimum scale ℃
Standard Temperature sensor dia. X length (d) x (L) mm
Temperature sensor length (L) mm
Minimum insertion requisite dimension
d= 6 DIA.
-50~ 50 2 10DIA.×100 105 140 100
120
90
145
165
145
120
100
90
80
70
110
100
80
75
140
120
120
150
130
110
95
105
90
165
165
205
205
240
125
160
185
160
125
105
95
80
65
110
95
85
75
95
×150
×100
×150
×200
×150
×150
×100
×100
×100
×100
×150
×100
×100
×100
2
2
1
1
1
2
2
2
2
5
5
5
10
10
-30~ 50
-20~100
-10~ 50
0~ 50
~ 60
~ 80
~100
~120
~150
~200
~250
~300
~400
~500
d= 8 DIA. d= 10 DIA.Maximum
Until 300 by the temperature sensor dia. 6 dia.( )
500
Bimetal Thermometers
Model
TB44
TB45
Size
100(4″)
125(5″)
D a b
116 17 57
145 17 57
H
117
117
Weight (L=150)
Approx. 550g
Approx. 720g
TB46 150(6″) 171 21 61 121 Approx. 850g
T
H3424
L
D DIA.
a
b
d DIA.
Tilt capabilities bimetal is a useful thermometer which can set the indicator to an arbitrary direction after installation.
13
Model number configuration For ordering, please specify the model number, each specs and range.
4T B① Bimetal Thermometers
Model name
② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪ ⑫ ⑬ ⑭ ⑮
Selective spec.Model number Additional spec. (Option)
Type 4 100 DIA.
5 125 DIA.
6 150 DIA.
Tilt capabilities type
Tilt capabilities type
Tilt capabilities type
Rain-proof
Rain-proof
Rain-proof
0
Welded type Boring type
Straight Taper
Welded type
General product for flange
SW11(SW10) SW41(SW40) SW71(SW70) SW81
SW12
SW13
SW14
SW15
SW42
SW43
SW44
SW45
SW72
SW73
SW74
SW75
SW82
―
―
―
Without well
Screw in a well①
With well
1 Inside screw: Standard (W22 a lot 14)
2 Inside screw: Rc1/2 Double socket
3 Inside screw: 1/2NPT Double socket
4 Inside screw: G1/2 Double socket
Connection part
②
5 Inside screw: Rc3/4 Double socket
0 Union type
0 R1/2
Connection screws
③ 1 R3/4
2 1/2NPT
3 G1/2B
4 G3/4B
5 JIS10K20ARF
6 JIS10K25ARF
7 ANSI1B150RF
8 ANSI1B300RF
A Set screw only (W22 a lot 14)
B R3/8
C R1
D 3/4NPT
E 1NPT
F JIS10K15ARF
G JIS10K40ARF
H JIS10K50ARF
J JIS20K20ARF
K JIS20K25ARF
L JIS10K15AFF
M JIS10K20AFF
N JIS10K25AFF
P ANSI3/4B150RF
Q ANSI3/4B300RF
R ANSI1B600RF
S ANSI 1 1/2B150RF
T ANSI 1 1/2B300RF
U ANSI 1 1/2B600RF
W JPI 1B150RF
X JPI 1B300RF
Y JPI 1B600RF
Z Input type
1 0 ~ 50, 60, 80, 100, 120, 150, 200, 250, 300
Range ℃ ④
2 0 ~ 400, 500
3 -10 ~ 50, -20 ~ 100, -30 ~ 50, -50 ~ 50
1 SUS304
Temperature sensor material
⑤ 2 SUS316
X In case with a well
0 d=6 dia.
Temperature sensor dia.
⑥ 1 d=8 dia.
2 d=10 dia.
L=300 (max.)
L=500 (max.)
L=500 (max.)
X In case with a well
Minimum dimension ~500mm
Temperature sensor length (mm) L dimension
⑦ X
A
In case with a well
1 Welded
Type of well⑬
4 Boring type straight
7 Boring type taper
8 Welded general product for flange
Screw within well
⑭ 1 W22 a lot 14
2 Rc1/2
3 1/2NPT
4 G1/2
5 Rc3/4
6 3/4NPT
7 G3/4
General products: Not available
General products: Not available
General products: Not available
General products: Not available
General products: Not available
0 Nil
Documents⑮
1 Required (Please specify the desired documents separately.) Submission drawings, instruction manual, inspection procedure, mill sheet, test report (1 pc 1 copy), traceability certificate, inspection certificate, dialstrength calculation, attended inspection
Specify the well model number. in another page.
*When ordering, please specify the temperature sensor and lead tracks length. *The model construction of well is SW ⑬⑭. *In case with a well, please specify SW type No. after the well [thermowell] manufacturing specifications at the P 14 to is referred.□
Bimetal Thermometers
Specify "X" if there is no specification item.
(When ordering, please specify the range and units separately.)
14
SMALL BIMETAL THERMOMETER: INDOOR TYPE
TB12 (T type) ・ TB22 (I type) ・ TB32 (V type) /60 DIA.
■TB12 (T type) ■TB22 ( I type) ■TB32 (V type)
■Specifications
■Scale range, temperature sensor dia. and temperature sensor length
●The minimum insertion dimension above is the dimension when there is no well. When there is a well, this dimension plus 25mm becomes the necessary minimum insertion dimension. ●The dimensions of this table are the maximum length the temperature sensor is inserted into the measurement liquid. ●When indicating the dimensions of the temperature sensor, please indicate the L dimension on this value is 5mm increments.
Manufacturing temperature range -50 ~ 50 ℃ → 0 ~ 500 ℃
Construction: indoor type, material: SPCC, finish: Ni plating
Temperature sensor: SUS304, Connection screw/flange: SUS304
Within ±2%F.S.
R1/2 (PT), R3/4 (PT), 1/2NPT, G1/2B (PF), G3/4B (PF)
JIS10K20ARF,JIS10K25ARF,ANSI1B150RF,ANSI1B300RF
Union type, Slide type Temperature sensor 6 dia. and the slide type in the TB12
are not available. When the maximum range exceeds 400
℃ or over, the slide type cannot be manufactured.
Double socket union type: R1/2, 1/2NPT (Connection)
6, 8, 10
12, 15 (The temperature sensor 6 dia. with a well cannot be manufactured.)
Without a well
With a well
Temperature sensor(d)
Well (d1)
Case
Wetted parts material
Accuracy
Standard connection screw
Standard connection flange
Connection shape
Temperature dia. (DIA.)
Scale range ℃
Minimum scale ℃
Standard Temperature sensor dia. X length (d) x (L) mm
Temperature sensor length (L) mm
Minimum insertion requisite dimension
d= 6 DIA.
-50~ 50 2 10DIA.×100 105 140 100
120
90
145
165
145
120
100
90
80
70
110
100
80
75
140
120
120
150
130
110
95
105
90
165
165
205
205
240
125
160
185
160
125
105
95
80
65
110
95
85
75
95
×150
×100
×150
×200
×150
×150
×100
×100
×100
×100
×150
×100
×100
×100
2
2
1
1
2
2
2
2
5
5
5
10
10
10
-30~ 50
-20~100
-10~ 50
0~ 50
~ 60
~ 80
~100
~120
~150
~200
~250
~300
~400
~500
d= 8 DIA. d= 10 DIA.Maximum
Until 300 by the temperature sensor dia. 6 dia.( )
500
Weight……Approx. 220g (L= 150)
Weight……Approx. 340g (L= 150) Weight……Approx. 400g (L= 150)
T
65
(6)
L
d DIA.
65 DIA.
15
(86)
36(6)
50L
d DIA.
65 DIA.
12
40
45゜
T
Bimetal Thermometers
42
(6)
50L
65 DIA.
d DIA.
1240
58
T
15
Model number configuration For ordering, please specify the model number, each specs and range.
T B① Bimetal Thermometers
Model name
② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪ ⑫ ⑬ ⑭ ⑮
Selective spec.Model number Additional spec. (Option)
Type 2 60 DIA.
2 60 DIA.
2
1
2
3 60 DIA.
T type
I type
V type
Small thermometer
Small thermometer
Small thermometer
0
Welded type Boring type
Straight Taper
Welded type
General product for flange
SW11(SW10) SW41(SW40) SW71(SW70) SW81
SW12
SW13
SW14
SW15
SW42
SW43
SW44
SW45
SW72
SW73
SW74
SW75
SW82
―
―
―
Without well
Screw in a well①
With well
1 Inside screw: Standard (W22 a lot 14)
2 Inside screw: Rc1/2 Double socket
3 Inside screw: 1/2NPT Double socket
4 Inside screw: G1/2 Double socket
Connection part
②
5 Inside screw: Rc3/4 Double socket
0 Union type
1 Slide type (When the maximum range at temperature sensor 6 dia. and in the TB12 exceeds 400℃ or over, the slide type cannot be manufactured.)
0 R1/2
Connection screws
③ 1 R3/4
2 1/2NPT
3 G1/2B
4 G3/4B
A Set screw only (W22 a lot 14)
Others (Model number products only)
1 0 ~ 50, 60, 80, 100, 120, 150, 200, 250, 300
Range ℃ ④
2 0 ~ 400, 500
3 -10 ~ 50, -20 ~ 100, -30 ~ 50, -50 ~ 50
1 SUS304
Temperature sensor material
⑤ 2 SUS316
X In case with a well
0 d=6 dia.
Temperature sensor dia.
⑥ 1 d=8 dia.
2 d=10 dia.
L=300 (max.) Non available with a well
L=500 (max.)
L=500 (max.)
X In case with a well
[Manufacturing range] ・Temperature sensor 6 dia. with a well is not available.
Minimum dimension ~500mm (until 300mm in case 6 dia.)
Temperature sensor length (mm) L dimension
⑦ X
A
In case with a well
1 Welded
Type of well⑬
4 Boring type straight
7 Boring type taper
8 Welded general product for flange
0 For the slide TB12 and General products: Not availableScrew within
well
⑭
1 W22 a lot 14
2 Rc1/2
3 1/2NPT
4 G1/2
5 Rc3/4
6 3/4NPT
7 G3/4
General products: Not available
General products: Not available
General products: Not available
General products: Not available
General products: Not available
0 Nil
Documents⑮
1 Required (Please specify the desired documents separately.) Submission drawings, instruction manual, inspection procedure, mill sheet, test report (1 pc 1 copy), traceability certificate, inspection certificate, dialstrength calculation, attended inspection
Specify the well model number. in another page.
*When ordering, please specify the temperature sensor and lead tracks length. *The model construction of well is SW ⑬⑭. *In case with a well, please specify SW type No. after the well [thermowell] manufacturing specifications at the P 14 to is referred.□
Bimetal Thermometers
Specify "X" if there is no specification item.
(When ordering, please specify the range and units separately.)
16
This device is a thermometer designed to perform temperature measurement especially in fields in which hygiene must be considered, and can be widely used in the food, pharmaceutical, cosmetic, and biological related fields.
・Since a filled liquid is not used, it can be used with confidence even when a well is not used. ・Since the case has a chrome plated finish, washing and draining are simple and it is extremely clean.
Cat. No.D03-02-E
Size: 75 DIA., 100 DIA. Connection type: Ferrule, with screw nut Size: 1S (Ferrule only), 1 1/2S, 2S Wetted parts material SUS316 or SUS304 Temperature range: 0 ~ 50 → 0 ~ 150 ℃ -30 ~ 50, -20 ~ 100 ℃
Accuracy: Within ±2%F.S. Case material: CAC203 chromate plating Case construction: Water-proof Weight: 75 DIA. Approx. 0.6kg 100 DIA. Approx. 0.9kg
OUTLINE
FEATURES
SPECIFICATIONS 1
Bimetal Thermometers (Sanitary Type)
17
Bimetal Thermometers (Sanitary Type)
・( ) in case of the size 75 ・When specifying the dimensions of the temperature sensor, please indicate the L dimension on the above list is 5mm increments. *This dimension is the minimum length to insert temperature sensor to a measurement medium.
Scale range ℃
Minimum scale ℃
Standard d×Lmm
Temperature sensor maximum length
Temperature sensor minimum insertion requisite L dimension (mm)*
d= 8 DIA. d= 10 DIA.
-30 ~ 50
-20 ~100
0 ~ 50
~100
~120
~150
2 10 DIA.×150 110
80
140
85
80
65
85
65
110200mm
65
65
55
×100
×150
×100
×100
×100
2
1
2
2
2(5)
Ferrule With screw nut
75 L
D DIA.
d DIA.
L75
D DIA.
d DIA.
Size
75
100
94
119
D
N2 Hex.
C2 DIA.
19.530
2.85
20。
C2 DIA.
C7 DIA.
Nominal dia.
C2
C7
1S
43.5
50.5
43.5
50.5
56.5
64
2S1 1/2S
Nominal dia.
C2
N2 Hex.
2S
56.242.7
56 x 64.7 71 x 82
1 1/2S
DIMENSIONS
SPECIFICATIONS 2
Scale range, temperature sensor dia. and temperature sensor length
Detailed viewFerrule ISO (IDF) standard With screw nut ISO (IDF) standard
18
Model number configuration For ordering, please specify the model number, each specs and range.
1T U 0① Bimetal Thermometers (Sanitary Type)
Model name
② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪ ⑫ ⑬ ⑭ ⑮
Selective spec.Model number Additional spec. (Option)
Model 3 75 DIA. Type DA
4 100 DIA. Type DA
Connection① 1 Ferrule
2 With screw nut
Connection screw
② 2 Size: 1S Ferrule only
3 Size: 1 1/2S or G1 1/2B
4 Size: 2S
3 SUS304
Wetted material③
4 SUS316
1 0 ~ 50, 100, 120, 150
Range ℃ ④
2 -30 ~ 50, -20 ~ 100
1 SUS304
Temperature sensor material
⑤ 2 SUS316
1 d= 8 DIA.
Temperature sensor dia.
⑥ 2 d= 10 DIA.
L= 200mm
Temperature sensor length (mm) L dimension
⑦ 0
0 Nil
Documents⑮
1 Required (Please specify the desired documents separately.) Submission drawings, instruction manual, inspection procedure, mill sheet, test report (1 pc 1 copy), traceability certificate, inspection certificate, dialstrength calculation, attended inspection
Bimetal Thermometers (Sanitary Type)
Specify "X" if there is no specification item.
(When ordering, please specify the range and units separately.)
19
THERMOWELL SPECIFICATIONS
■Connection parts and dimensions ■Thermowell shape and size
M
J
TSX Hex.
(10)
Taper Screw
Straight Screw
M
J
S
X Hex.
(10) (25)
T(PT) R
X Hex.
W DIA.
T
M
J3
(10)
M(10) (25)
X Hex.
W DIA.
T
45(10)
45(10) (25)
T
R1/2
R3/4
G1/2B
G3/4B
J S W X M
18 8 - 27×31.2 43
20 9.5 - 30×34.6 45
18 - 32 32×37 43
20 - 36 36×41.6 45
Welding type
Welding type
Drilled type (Straight)
Screw type
Drilled type (Taper)
Drilled type (Straight)
Drilled type (Taper)
Flange type
Welding
L
d1 DIA.
T
d2 DIA.
L
d1 DIA.
T
L
d1 DIA.
Welding
d2 DIA.
L
d1 DIA.
WeldingWelding
L
d1 DIA.
Thermowell
Bulb
Outer dia. (d1DIA.)
Inner DIA. (d2DIA.)
Type
dDIA.
Drilled type Welding type Drilled type Welding type Drilled type Welding type
8.5 8.5 10.5 11 13.5 13.5 13.5 16.5
8 8 10 10 13 13 13 16
Drilled type
12 15 19 19/23 23 Thermowell
Outer dia.(d1) Type
Drilled typeWelding type
Drilled type
Welding type
Drilled type
Welding type
Drilled type
Drilled type
Screw(T) Flange1/2 3/4 JIS,ANSI,JPI
○ ○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○
○
○
12DIA.
15DIA.
19DIA.
23DIA.
19DIA./23DIA.(Taper)
R
R
T
WeldingWelding
L
d1 DIA.
Bulb
Thermowell
d DIA.
d1 DIA.
d 2 DIA.
JIS,ANSI,JPI
Bimetal Thermometers
Standard type
Double socket type
Double socket type
Double socket type
Standard type
Standard typeScrew type Union type
Flange type Union type
Note) Please refer to JIS, ANSI, and JPI standard for flange size.
■Relation of themowell and bulb
■Thermowell material
SUS304, SUS316, SUS316L, titanium, Hastelloy-B , and Monel-metal are available. Teflon or Glass coating is available. Coated thermowell is available with flange type only.
Thermowell …… material
Inside screws (Connecting screws with thermometer): W22 thread 14 or Rc1/2
■Thermowell DIA. and type (screw, flange)
(mm)
Weld the pipe as shown below.
Weld the pipe as shown below.
R
14
Model number configuration For ordering, please specify the model number, each specs and the range.
S W 1① Welding type thermowell ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪ ⑫ ⑬ ⑭ ⑮
Welding type straight For slide type
Selective spec.Model Additional spec. (option)
Model
1
0
Welding type straight Inside screws
2 Welding type straight Inside screws
3 Welding type straight Inside screws
4 Welding type straight Inside screws
W22 a lot 14
W16-18 (8DIA.), W20-16 (10DIA.), W22-14 (13DIA.)
Rc1/2
1/2NPT
G1/2
Rc3/4
3/4NPT
G3/4
5 Welding type straight Inside screws
6 Welding type straight Inside screws
7 Welding type straight Inside screws
00 R1/2
Connection part①②
1/2NPT
R3/4
03
02
01
G1/2B
04 G3/4B
0C R1
0D 3/4NPT
Material③
05 JIS10K20ARF
ANSI 1B300RF
ANSI 1B150RF
0F
08
07
JIS10K15ARF
0G JIS10K40ARF
0H JIS10K50ARF
0J JIS20K20ARF
0K JIS20K25ARF
ANSI 3/4 150RF
JIS10K25AFF
0Q
0P
0N
ANSI 3/4 300RF
0S ANSI 1 1/2 150RF
0T ANSI 1 1/2 300RF
0W JPI 1 150RF
0X JPI 1 300RF
06 JIS10K25ARF
0L JIS10K15AFF
0M JIS10K20AFF
TF,GF,MF,FMF,RJ (specified)
1 SUS304
2 SUS316
1 Outer dia. 12DIA.
Outer dia.④
2 Outer dia. 15DIA.
3 Outer dia. 19DIA.
SUS304
L dimension (mm)
⑤ 0
1
2
3
4
5
6
7
8
9
SUS316
A
B
C
D
E
F
G
H
J
K
~ 100
101~ 200
201~ 300
301~ 400
401~ 500
501~ 600
601~ 700
701~ 800
801~ 900
901~1000
1001~(/100mm)
0 Nil
Documents⑮
1 Required (Please specify the desired documents separately.)
*Specify "X" if there is no specification item.
Submission drawings, instruction manual, inspection procedure, mill sheet, test report (1 pc 1 copy), strength calculation, attended inspection
Bimetal Thermometers
15
Model number configuration For ordering, please specify the model number, each specs and the range.
S W① Drilled type thermowell ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪ ⑫ ⑬ ⑭ ⑮
Drilled type straight For slide type
Selective spec.Model Additional spec. (option)
Model
1
0
Drilled type straight Inside screws
2 Drilled type straight Inside screws
3 Drilled type straight Inside screws
4 Drilled type straight Inside screws
W22 a lot 14
W16-18 (8DIA.), W20-16 (10DIA.), W22-14 (13DIA.)
Rc1/2
1/2NPT
G1/2
Rc3/4
3/4NPT
G3/4
W16-18 (8DIA.), W20-16 (10DIA.), W22-14 (13DIA.)
5 Drilled type straight Inside screws
6 Drilled type straight Inside screws
7 Drilled type straight Inside screws
0 Drilled type taper For slide type
W22 a lot 141 Drilled type taper Inside screws
Rc1/22 Drilled type taper Inside screws
1/2NPT3 Drilled type taper Inside screws
G1/24 Drilled type taper Inside screws
Rc3/45 Drilled type taper Inside screws
3/4NPT6 Drilled type taper Inside screws
G3/47
4
4
4
4
4
4
4
4
7
7
7
7
7
7
7
7 Drilled type taper Inside screws
00 R1/2
Connection part①②
1/2NPT
R3/4
03
02
01
G1/2B
04 G3/4B
0B R3/8 (12 DIA. only)
0C R1
Material*③
0D 3/4NPT
06 JIS10K25ARF
ANSI 1B300RF
ANSI 1B150RF
0F
08
07
JIS10K15ARF
0G JIS10K40ARF
0H JIS10K50ARF
0J JIS20K20ARF
0K JIS20K25ARF
0M JIS10K20AFF
ANSI 3/4 150RF
JIS10K25AFF
0Q
0P
0N
ANSI 3/4 300RF
0S ANSI 1 1/2 150RF
0T ANSI 1 1/2 300RF
0W JPI 1 150RF
0X JPI 1 300RF
05 JIS10K20ARF 0L JIS10K15AFF TF,GF,MF,FMF,RJ (specified)
1 SUS304
2 SUS316
5 SUS316L
1 Outer dia. 12DIA.
Outer dia.④
2 Outer dia. 15DIA.
3 Outer dia. 19DIA.
4 Outer dia. 23DIA.
5 Outer dia. 19, 23DIA.
Specified outer dia.
SUS304
L dimension (mm)
⑤ 0
1
2
3
4
5
6
7
SUS316
A
B
C
D
E
F
G
H
SUS316L
a ~ 100
b 101~ 200
c 201~ 300
d 301~ 400
e 401~ 500
f 501~ 600
g 601~ 700
h 701~ 800
0 Nil
Documents⑮
1 Required (Please specify the desired documents separately.)
【Manufacturing range】 Manufacturing range of connecting screws and well 3/8 : Well outer diameter 12DIA. drilling only 1/2 : Well outer diameter 12, 15DIA. 3/4, 1: Well outer diameter 12, 15,19DIA., 19/23DIA.
*For drilled type, titanium, Hastelloy R and other special materials are also available. Please specify the material.
*Specify "X" if there is no specification item.
Submission drawings, instruction manual, inspection procedure, mill sheet, test report (1 pc 1 copy), strength calculation, attended inspection
Bimetal Thermometers
16
Model number configuration For ordering, please specify the model number, each specs and the range.
S W 8 1① Welding type thermowell
(Flange type)② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪ ⑫ ⑬ ⑭ ⑮
Welding type straight Inside screws
Selective spec.Model Additional spec. (option)
Model
2
1
Welding type straight Inside screws Rc1/2
W22 a lot 14
05 JIS10K20ARF
Connection part①②
ANSI 1B150RF
JIS10K25ARF
08
07
06
ANSI 1B300RF
0F JIS10K15ARF
0G JIS10K40ARF
0H JIS10K50ARF
Material③
0J JIS20K20ARF
0L JIS10K15AFF
JIS10K25AFF
JIS10K20AFF
0P
0N
0M
ANSI 3/4 150RF
0Q ANSI 3/4 300RF
0S ANSI 1 1/2 150RF
0T ANSI 1 1/2 300RF
0W JPI 1 150RF
0K JIS20K25ARF 0X JPI 1 300RF
1 SUS304
1 Outer dia. 12DIA.
Outer dia.④
2 Outer dia. 15DIA.
3 Outer dia. 19DIA.
L dimension (mm)
⑤ 0
1
2
3
4
5
6
7
8
9
~ 100
101~ 200
201~ 300
301~ 400
401~ 500
501~ 600
601~ 700
701~ 800
801~ 900
901~1000
1001~(/100mm)
0 Nil
Documents⑮
1 Required (Please specify the desired documents separately.)
*Specify "X" if there is no specification item.
THERMOWELL FLANGE TYPE SPECIFICATIONS
WeldingWelding Welding
L60
d1 DIA.
L+60
d2 DIA.
■Shape and size ■Relation of thermowell and bulb
■Thermowell material
■Thermowell DIA. and flange
Pipe and flange are welded as shown below.
Thermowell material …… SUS304
Inside screws (Connecting screws with thermometer): W22 a lot 14・Rc1/2
Bulb
Thermowell
d DIA.
Type
Inner dia. (d2 DIA.)
Outer dia. (d1 DIA.)
8
8.5
12
10
Welding type
11
15
13
13.5
19
19 DIA.
15 DIA.
12 DIA.
Outer dia. (d1)
Welding type
Type
Thermowell
○
○
○
Flange
JIS, ANSI, JPI
Bulb
Thermowell
d1 DIA.
d2 DIA.
d DIA.
Submission drawings, instruction manual, inspection procedure, mill sheet, test report (1 pc 1 copy), strength calculation, attended inspection
Bimetal Thermometers
17
100% Recycled Paper. PRINTED IN JAPAN ,07.10.F(N)
The contents in the catalogue are subject to change without notice.
● ADZ NAGANO GmbH Bergener Ring 43 01458 Ottendorf-Okrilla, Germany Phone :+49-35205-596930 F a x :+49-35205-596959 ● Nagano Keiki Solutions Support Center Bergener Ring 43 01458 Ottendorf-Okrilla, Germany Phone :+49-35205-75701 F a x :+49-35205-75702
● NAGANO FUKUDA (TIANJIN) INSTRUMENTS CO., LTD. 801-805, Future Holiday Plaza, Jiomen, Fengtai district, Beijing China Phone :+86-10-8758-2461 F a x :+86-10-8758-2462
● KOREA NAGANO CO., LTD. #296-2 Osan-ri, Dongtan-myun, Hwaseong-shi, Kyonggi-do, Korea Phone:+82-31-379-3934 F a x :+82-31-379-3936
OVERSEAS SALES DEPT : 1-30-4, HIGASHIMAGOME OHTA-KU, TOKYO, JAPAN Phone : +81-3-3776-5328 F a x : +81-3-3776-5447 E-mail : [email protected] URL : http://www.naganokeiki.co.jp/
OVERSEAS SALES DEPT.
● ASHCROFT-NAGANO, INC.
● OVERSEAS PLANT ○ OVERSEAS SALES NETWORK
SINGAPOREMALAYSIA
THAILAND
INDONESIA PHILIPPINES AUSTRALIA
TAIWAN
U.S.A.JAPANKOREACHINAGERMANY