bill of quantity - employees' state insurance · 2019-02-20 · cleaning and desilting of...
TRANSCRIPT
S.No PARTICULAR OF ITEMS QTY RATE UNIT AMOUNT
1 2.31
Clearing jungle including uprooting of rank
vegetation, grass, brush wood, trees and saplings of
girth up to 30 cm measured at a height of 1 m above
ground level and removal of rubbish up to a distance
of 50 m outside the periphery of the area cleared.
2000 Sqm
2 2.32
Clearing grass and removal of the rubbish up to a
distance of 50 m outside the periphery of the area
cleared.
5000 Sqm
3 14.78
Cleaning of under ground sump, Over Head R.C.C.
Tank(independent staging) including disposal of slit
and rubbish, all as per direction of Engineer-in-
charge. The cleaning shall consist following
operations:-
350 Sqm
(i)
Tank shall be emptied of water by pumping & bottom
shall be cleaned of slit and other deposits.
(ii)
Entire surface area of the sump shall then scrubbed
thoroughly with wire brush etc. and pressure washed
with water.
(iii)chlorination of RCC internal surface by liquid chlorine.
(iv)
The treated surface shall be dried using air jetting
and all loose particles shall be removal from the
surface.
(v)
Finally the surface shall be treated with ultraviolet
radiation etc. as per direction of Engineer-in-Charge.
4 1.1.1
Carrige of malba building rubbish by machnical
transport including loading unloading and stacking
upto 5 Km.
300 Cum
5 1.1.3
Carrige of Manure or Sludge by machnical transport
including loading unloading and stacking upto 5 Km. 100 Cum
Bill of QuantityPART- B
6 14.75A
Cleaning of terrace/loft water storage tank (inside
surface area) upto 2000 litre capacity at all heights
with coconut brushes, duster etc. removal of silt,
rubbish from the tack and cleaning the tank with
fresh water disinfecting with bleaching powder @ 0.5
gm per litre capacity of tank, including making the
date of cleaning on the side of tank body with the
help of stencil and paint and disposing of malba, all
complete as per direction of Engineer-in-charge. (The
old date already written on tank should be removed
with paint remover or black paint and if date is not
written with the stencil or old date is not removed
deduction will be made @ Rs. 0.10 per litre if during
cleaning any GI fittings or ball cock is damaged that is
to be repaired by contractor at his own cost and
nothing extra will be paid on this account)
80000 Ltr
7 14.76
Cleaning and desilting of gully trap chamber,
including removal of rubbish mixed with earth etc.
and disposal of same, all as per the direction of
Engineer-in-charge.
30 Each
8 14.77
Cleaning of chocked sewer line by diesel running
vehicle mounting hydraulic operated high pressure
suction cum jetting sewer cleaning machine fitted
with pump having 4000 litres suction capacity and
6000 litres water jetting tank capacity including
skilled operator, supervising engineer etc. for
cleaning and partial desilting of manholes and
dechocking of sewer lines. Dechocking and flushing of
sewer line from one manhole to another ny high
pressure jetting system of 2200 PSI for sewer line
from 150mm dia upto 300mm dia for all depth.
250 Mtr
9 4.1.2
Providing and laying in position cement concrete of
specified grade excluding the cost of centring and
shuttering - All work to any level 1:1.5:3 (1 Cement :
1.5 Coarse sand : 3 graded stone aggregate 220 mm
nominal size.)
5 Cum
10 4.1.5
Providing and laying in position cement concrete of
specified grade excluding the cost of centring and
shuttering - All work to any level 1:3:6 (1 Cement : 3
Coarse sand : 6 graded stone aggregate 220 mm
5 Cum
11 4.17
Making plinth protection 50mm thick of cementt
concrete 1:3:6( 1 cement : 3 coarse sand : 6 graded
stone aggregate 20 mm nominal size) over 75mm
bed by dry brick ballast 40mm nominal size well
rammed and consolidated and grouted with fine sand
including finishing the top smooth.
100 Sqm
12 5.9.5
Centering and shuttering including strutting, propping
etc. and removal of formm work for : lintels, beams,
plinth neams, girders, bressumrs and cantilevers.
15 Sqm
13 5.22.6
Steel reinforcemen for R.C.C. work including
straightening, cutting, nemding, nplacing in position
and binding all complete upto plinth level. Thermo-
mechnacally Treated bars.
500 Kg
14 6.1.1
Brick work with common burnt clay F.P.S (non-
modular) brick of class designation 7.5 in foundation
and plinth in:6.1.1 Cement mortar 1:4 ( 1 Cement : 4
Coarse sand)
10 Cum
15 6.12.1
Half brick masonry with common burnt clay F.P.S
(non modular) bricks of class designation 7.5 in
foundation and plinth in 6.12.1 Cement mortar 1:3 (
5 Sqm
16 6.4.2 Cement mortar 1 :6 (1 Cement : 6 Coarse Sand) 5 Cum
9.20
Providing and fixing ISI marked flush door shutters
conforming to IS: 2202 (Part I) decorative type, core
of block board construction with frame of 1st class
hard wood and well matched teak 3 ply veneering
with vertical grains or crooss bands and face venners
9.20.135mm thick includin ISI marked Stainless Steel butt
hinges with necessary screws.30 Sqm
9.46
Providing and fixing curtain rods of 1.25 mm thick
chromium plated brass plate, with two chromium
plated brass brackets fixed with C.P. brass screws and
wooden plugs, etc. wherever necessary complete : 25
mm dia.
9.46.2 20mm dia 20 Mtr
9.48
Providing and fixing M.S. Grills of required pattern in
frames of windows etc. with M.S. Flats, square or
round bars etc. including priming coat with approved
steel primer all complete.9.48.1 Fixed to steel windows by weldin. 200 Kg
9.48.2Fixed to openings/ wooden frames with raw plugs
screws etc.100 Kg
17
18
19
20 9.118.1
Providing and fixing to existing door frames. 24mm
thick factory made PVC door shutters made of styles
and rails of a UPVC hollow section of size 59X24mm
and wall thickness 2mm (+- 0.2mm) with inbuilt
edging on both sides. The styles and rails mitred and
joint at the corners by means of M.S.
galvanised/plastic brackets of size 75X220mm having
wall thickness 1.0mm and stainless steel screws. The
styles of the shutter reinforced by inserting
galvanised M.S. tube of size 20X20mm and 1mm(+-
0.1mm) wall thickness. The lock rail made up of 'H'
section, a UPVC hollow section of size 100X24mm
and 2mm (+-0.2mm) all thickness, fixed to the
shutter styles by means of plastic/galvanised M.S. 'U'
cleats. The shutter frame filled with a UPVC multi-
chambered single panel of size not less than 620mm,
having over all thickness of 20mm and 1mm(+-
0.1mm) wall thickness. The panels filled vertically and
tie bar at two places by inserting horizontally 6mm
galvanised M.S. rod and fastened with nuts and
washers, complete as per manufacturer's
specificaton and direction of Engineer-in-charge. (For
W.C. and Bathroom door shutter).
30 Sqm
21 9.119
Providing and fixing factory made P.V.C. door frame
of size 50X47 mm with a wall thickness o 5mm, made
out of extruded 5mm rigid PVC foam sheet, mitred at
corners and joined with 2 Nos. of 150mm long
brackets of 15X15mm M.S. square tube, the vertical
door frame proffiles to be reinforced with 19X19mm
M.S. square rube of 19 auge, EPDM rubber gasket
weather seal to be provided through out the frame.
The door frame to be fixed to the wall using M.S.
screws of 65/100 mm size, complete as per
manufacturers specification and direction of Engineer-
in-charge.
10 Mtr
22 10.1
Structural steel work in single section fixed with or
without connecting plate including cutting, hoisting,
fixing in position and applying a priming coat of
approved steel primer all complete.
10 Kg
23 11.36
Providing and fixing Ist quality ceremic glazed wall
tiles conforming to IS : 15622(thickness to be
specified by the manufacturer) of approved make in
all colours, shades except burgundy, botle green,
black of any size as approved by Engineer-in-charge
in skirting, risers of steps and dados over 12mm thick
bed of cement morar 1:3(1 cement : 3 coarse sand)
and jointing with grey cement slurrt @ 3.3kg per sqm
including pointing in white cement mixed with
pigment of matching shade complete.
200 Sqm
24 11.37
Providing and laying Ceramic glazed floor tiles
300X300mm (thickness to be specified by
manuacturer) of 1st quality conforming to IS : 15622
of approved make in colours such as White, Ivory,
Grey, Fume red, Brown, laid on 20mm thick Cement
Mortar 1:4 (1 cement: 4 Coarse sand) including
pointing the joints with white cement and matching
pigment ec. complete.
100 Sqm
11.47
Providing and laying Vitrified tiles in floor with
different sizes (thickness to be specified byy the
manufacturer), with water absorption less htan
0.08% and conforming to IS: 15622, of approved
brand & manufacturer in all colours and shade, laid
with cement based high polymer modified quick set
tile adhesive (water based) conforming to IS : 15477,
in average 6mm thickness, includin grouing og joints
(Payment for grouting of joint to be made
separately).
11.47.2 Size of Tile 600X600 mm 150 Sqm
26 12.1.3
Providing corrugated G.S. sheet roofing including
vertical/ curved surfface fixed with polymer coated J
and L hooks, bolts and nuts 8mm diameter with
bituman and G.I. limpet washers filled with white
lead and including a coat of approved steel primer
and two coats of approved paint on overlapping of
sheets complete upto any pitch in horizontal/ vertical
or curved surfaces) excluding the cost of purlins,
rafters and trusses and including cutting to size and
shape wherever reuired. 0.63 mm thick with zinc
coating not less than 275gm/sqm.
20 Sqm
12.41
Providing and fixing on wall face Unplasticised Rigid
PVC arin water pipes conforming to IS: 13592 Type A
including jointing with seal rintg conforming to IS :
5382 leaving 10mm gap for thermal expansion. (i)
single socketed pipes.12.41.1 (a) 75mm diameter 30 Mtr
25
27
12.41.2 (b) 110mm diameter 200 Mtr
28 13.1.112mm cement plaster of mix 1 :4 (1 cement : 4 fine
sand) 100 Sqm
29 13.2.1
15mm cement plaster on the rough side of single or
half brick wall of mix 1 : 4(1 cement : 4 coarse sand)
10 Sqm
30 13.16.16mm cement plaster of mix 1 :3 (1 cement : 3 fine
sand) 10 Sqm
31 13.37White wash with lime to give an even shade : New
work (three or more coats)100 Sqm
32 14.42White wash with lime to give an even shade : Old
work (two or more coats)300 Sqm
33 13.41.1
Distemparing with oil bound washable distemparing
of approved brand and manufacture to give an even
shade : New work(Two or more coats) over and
including water thinable priming coat with cement
primer.
100 Sqm
34 13.44.1
Finishing walls with water proofing cement paint of
required shade : New work (Two or more coats
applied @ 3.84kg/10sqm)
100 Sqm
35 14.64.2
Finishing walls with water proofing cement paint of
required shade : Old work (One or more coats
applied @ 2.20kg/10sqm)
3000 Sqm
13.47
Finishing walls with Premium Acrylic Smooth exterior
paint with Silicon additives of required shade
13.47.1
New work (Two or more coats applied @
1.43ltr/10sqm over and including priming coat of
exterior primer applied @2.20kg/10sqm)
300 Sqm
14.67
Finishing walls with Premium Acrylic Smooth exterior
paint with Silicon additives of required shade
14.67.1Old work (Two or more coats applied @
1.43ltr/10sqm)5000 Sqm
38 14.5.1
Renewing glass panes, with putty and nails wherever
necessary including racking out the old putty : Float
glass panes of thickness 4mm.
200 Sqm
39 14.6.1
Renewing glass panes, with wooden fillets wherever
necessary Float glass panes of thickness 4mm.
50 Sqm
40 14.43
Removing white or colour wash by scrapping and
sand papering and preparin the surface smooth
including necessary repairs to scratches etc.
complete.
5000 Sqm
41 14.45.1
Distemparing with oil bound washable distemparing
of approved brand and manufacture to give an even
shade : Old work(One or more coats).
10000 Sqm
27
36
37
42 14.46
Removing dry or oil bound distemper, water proofing
cement paint and the like by screpping, sand
papering and preparing the surface smooth including
necessary repairs to scratches etc. complete.
15000 Sqm
43 14.53.1
Wall painting with plastic emulsion paint of approved
brand and manufacture to give an even shade : One
or more coats on old work.
100 Sqm
44 14.54
Painting with synthetic enamel paint of approved
brand and manufacture of reqrited colour to give an
even shade : one or more coats on old work.
3000 Sqm
45 15.2.1
Demolishing cement concrete manually/ by
mechanical means including disposal of material
within 50 metres lead as per direction of Engineer-in-
charge. Nominal concrete 1:3:6 or richer mix (i/c
equivalent design mix)
20 Cum
46 15.3
Demolishing R.C.C. work manully/ by mechanical
means including stacking of steel bars and disposal of
unserviceable material within 50 metres lead as per
direction Engineer-in-charge.
10 Cum
15.7
Demolishing Brick work manully/ by mechanical
means including stacking of serviceable material and
disposal of unserviceable material within 50 metres
lead as per direction Engineer-in-charge.
15.7.4 In Cement Mortar 10 Cum
15.23
Dismantling tile work in floors and roofs laid in
cement mortar including sraking material within 50
metres lead.
15.23.1 For thickness of tiles 10mm to 25mm 20 Sqm
49 15.56
Dismantling old plaster or skirting raking out joints
and cleaning the surface for plaster including disposal
of rubbish to the dumping ground within 50 metres
lead.
200 Sqm
47
48
21.1
Providing and fixing aluminium work for doors,
windows, ventilators and partitionswith extruded
built up standard tubular sections/ appropriate Z
sections and other sections of approved make
conforming to IS : 733 and IS : 1285, fixing with dash
fasteners of required dia and size, including
necessary filling up the gaps at junctions, i.e. at top,
bottoms and sides with required EPDM rubber/
neoprene gasket etc. Aluminium sections shall be
smooth, rust free, straight, mitred and jointed
mechnically wherever required including cleat angle,
Aluminium snap beading for glazing / paneling, C.P.
brass / stainless steel screws, all complete as [er
architectural drawings and the directions of Engineer-
in-charge. (Glazing, paneling and dash fasteners to be
paid for separately) :
21.1.1.2Powder coated aluminium (minimum thickness of
powder coating 50 micron)100 Kg
51 21.1.2.2
for shutter of doors, windows & ventilators including
providing and fixing hinges/ pivots and making
provision fofr fixing of fittings wherever required
including the cost of EPDM rubber/ neoprene gasket
required (Fittings shall be paid for separately).
Powder coated aluminium (minimum thickneess of
powder coating 50 micron)
100 Kg
52 21.2.2
Providing and fixing 12mm thick Pre-laminated
particle board flat pressed thtree layer or graded
wood particle board conforming to IS : 12823 Grade I
Type II, in panelling fixed in aluminium doors, indows
shuters and parition frames with C.P. brass/ stainless
steel screws etc. complete as per architectural
drawings and directions of engineer-in-charge. Pre-
laminated particle board with decorative lamination
on boh sides.
50 Sqm
53 21.3.1
Providing and fixing glazing in aluminium door,
window, ventilator shutters and partittions etc. with
EPDM rubber/neoprene gasket etc. conplete as per
the architectural drawings and the directions of
engineer-in-charge. (Cost of aluminium snap beading
shall be paid in basic item) : With float glass panes of
4.0 mm thickness.
50 Sqm
50
54 21.8.1
Fillng the gap in between aluminium frame &
adjacent RCC/ Brick/ Stone work by providing
weather silicon sealant over backer rod of approved
quality as per architectural drawings and direction of
Engineer-in-charge complete. Upto 5mm depth and
5mm width.
10 Mtr
55 21.13
Providing and fixing 100mm brass locks (best make of
approved quality) for aluminium doors including
necessary cutting and making good etc. complete.
10 Each
56 21.17
Providing and fixing anodised aluminium grill
(anodised transparent or dyed o required shade
according to IS : 1868 with minimum anodic coating
of grade AC 15) of approved design/pattern, with
approved standard section and fixed to the exising
window frame with C.P. brass/ stainless steel screws
@ 200mm center to center, including cutting he grill
to proper opening size for fixing and operation of
handles and fixing approved anodised aluminium
standard section around the opening, all complete as
per requirement and direction of Engineer-in-charge.
(Only weight of grill to be measured for payment).
50 Kg
57 22.14.1
Grading roof for water proofing treatment with
Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4
graded stone aggregate 20mm nominal size)
10 Cum
58 13.26
Providing and applying plaster of paris putty of 2mm
thickness over plastered surface to prepare the
surface even and smooth complete.
3000 Cum
59 17.1.1
Providing and fixing water closet squatting pan
(Indian type WC pan) with 100mm sand cast Iron P or
S trap, 10 litre low level white PVC flushing cistern,
including flush pipe, with manually controlled device
(handle lever) conforming to IS : 7231, with all fittings
and fixtures complete, including cutting and making
good the walls and floors wherever required : White
Vitreous china Orissa pattern WC Pan of size
580X440mm with intergral type foot rests.
20 Sqm
60 14.75
Repairs to plaster of thickness 12mm to 20mm in
patches of area 2.5 sqm and under, including cutting
the patch in proper shape, raking out joints and
preparing and plastering the surace of the walls
complete, including disposal of rubbish to the
dumping ground within 50 metres lead : With cement
mortar 1 :4 (1 cement : 4 fine sand)
1000 Sqm
61 14.72
Providing and fixing double scaffolding system (cup
lock type) on the exterior side, up to seven story
height made with 40 mm dia MS tube 1.5m centre to
centre, horizontal & vertical tuber joining with cup &
lock system with MS tubes, MS tube challies, MS
clamps and MS staircase system in the scaffolding for
working platform etc. and maintaining it in a
serviceable condition for the required duration as
appproved and removing it there after. the
scaffolding system shall be stifened with bracings,
runners, connection with the building etc wherever
required for inspection of work at required locations
with essential safety features for the workmen etc.
complete as per directions and approval of Engineer-
in- charge. The elevational area of the scaffolding
shall ne measured for payment purpose. The
payment will be made once irrespective of duration
of scaffolding.
200 Sqm
62 17.7.2
Providing and fixing wash basin with CI breakets,
15mm CP Brass pillar taps, 32mm CP brass waste of
standard pattern, including painting of fittings and
brackets, cutting and making good the walls
wherever require: White Vitreous China Wash basin
size 630X450 mm with a single 15mm CP brass pillar
tap.
30 Each
63 17.3.1
Providing and fixing white vitreous china pedestal
type water closet (European type) with seat and lid,
10 litre low level white vitreous china flushing cistern
& CP flush bend with fittings & CI Breakets, 40mm
flush bend, overflow arrangement with specials of
standard make and mosquito proof coupling of
approved municipal design complete, including
painting of fittings and brackets, cutting and making
good the walls and floors wherever required : WC
pan with ISI marked white solid plastiv seat and lid.
10 Each
64 17.10.1.2
Providing and fixing Stainless steel A IS 1304 (18/8)
kitchen sink as per IS : 13983 with CI brackets and
stainless steel plug 40mm, including painting of
fittings and brackets, cutting and making good the
alls wherever required: 510X1040mm bowl depth
225mm.
10 Each
S.No DSR No. PARTICULAR OF ITEMS QTY RATE UNIT AMOUNT
1 295 Stone Aggregate (Single size) : 20mm nominal size10 Cum
2 296 Stone Aggregate (Single size) : 12.5mm nominal size5 Cum
3 NDSR Portland cement (PPC) 200 Bag
4 367 Portland cement (OPC- 43 Grade)) 10 Bag
5 368 White cement 5 Bag
6 595 Bright finished or black enameleed mild steel butt
hinges 100X58X1.90mm2 10 Nos
7 596 Bright finished or black enameleed mild steel butt
hinges 75X47X1.70mm2 10 Nos
8 701 Anodised Aluminium tower bolt (barrel type)
150X10mm5 10 Nos
9 702 Anodised Aluminium tower bolt (barrel type)
100X10mm5 10 Nos
10 705 Anodised Aluminium handles 75mm with plate
25X32mm5 10 Nos
11 706 Anodised Aluminium Kicking Plate 50cm 5 Each
12 982 Coarse sand (Zone- III) 50 Cum
13 983 Fine sand (Zone-IV) 80 Cum
14 1159 Stone dust 5 Cum
15 1301 Sodium Hypochlorite(water Disifectant) Bleaching
Powder1 Quintal
16 1545 G.I. Pipes 15mm dia 350 Mtr
17 1546 G.I. Pipes 20mm dia 100 Mtr
18 1547 G.I. Pipes 25mm dia 50 Mtr
19 1641 G.I. Union 15mm Nominal Bore 400 Each
20 1642 G.I. Union 20mm Nominal Bore 50 Each
21 1163 G.I. Union 25mm Nominal Bore 50 Each
22 1649 Polythylene water storage tank with cover and
suitable locking arrangement.3000 Per Ltr
23 1872 White Vitreous china laboratory sink
600X450X200mm5 Each
24 1875 White Plastic seat (solid) with lid C.P. brass hinges
and rubber buffers.15 Each
25 1878 Shower rose C.P. brass for 15 to 20 mm inlet 100mm
dia50 Each
Total
PART- C Supply Of Materials
26 1922 H.P. or L.P. ball valve with polyethene floats : 15mm
dia150 Each
27 1923 H.P. or L.P. ball valve with polyethene floats : 20mm
dia50 Each
26 1924 H.P. or L.P. ball valve with polyethene floats : 25mm
dia10 Each
28 1933 Gun metal non return wall- Horizontal (Screwed end)
25mm dia 1 Each
29 1947 Vitreous China flat back wash basin 630X450 mm20 Each
30 1954 Vitreous China Orisa type W.C. pan size 580 mm10 Each
31 1955 Vitreous China Pedestal type water closet 10 Each
32 2412 Plywood 5mm Ply with commercial ply on both faces
6mm thick30 Sqm
33 2456 Hydrolic door closer bottle type M.S. body with
necessary accessories and screws complete.
10 Each
34 2459 Anodised Aluminium hanging type door stopper 30 Each
35 7257 C.P. brass bib cock 15 mm 200 Each
36 7260 C.P. Brass stop cock(Consealed) 15 mm 30 Each
1342 Brass Stop cock 30 Each
37 7261 C.P. brass angle wall 100 Each
38 7113 Rectangular shape 453X357mm mirror with plastic
moulded frame20 Each
39 7117 Semi Regid PVC waste pipe for sink and wash basin
32mm dia with length not less than 700 mm i/c PVC
waste fittings.
100 Each
7118 Semi Regid PVC waste pipe for sink and wash basin
40mm dia with length not less than 700 mm i/c PVC
waste fittings.
50 Each
40 7188 UPVC pipes (working presure 4 kg/ cm2) single
socketed pipe 75mm dia50 Each
41 7189 UPVC pipes (working presure 4 kg/ cm2) single
socketed pipe 110mm dia50 Each
42 7190 UPVC pipes (working presure 4 kg/ cm2) Rubber(seal)
ring 75mm dia50 Each
43 7191 UPVC pipes (working presure 4 kg/ cm2) rubber (seal)
ring 110mm dia50 Each
44 NDSR C.P. Brass pillar cock 100 Each
45 592 C.P. Brass Powder coated curtain rod 25 dia 20 Each
46 446 M.S. Powder coated side bracket for curtain rod with
screws & accessories complete in all respect.
50 Each
47 7358 Flushing Cistern P.V.C. 10 lts capacity (low level)
(white) (with fittings, accessories and flush pipe)
50 Each
48 7400 PTMT bib cock 15 mm 20 Each
49 7403 PTMT stop cock 15 mm (male thread) 20 Each
50 7406 PTMT piller cock 20 Each
51 7411 Grating with waste hole 125mm 80 Each
52 7495 PTMT- Ball cock 15mm complete with Epoxy Coated
Aluminium Rod & H.D. Ball10 Each
54 7496 PTMT- Ball cock 20mm complete with Epoxy Coated
Aluminium Rod & H.D. Ball10 Each
55 2413 Commercial ply 12mm 10 Sqm
56 669 M.S. Handle 4" 40 Each
57 668 M.S. Handle 5" 40 Each
58 NDSR G.I. Socket 15mm dia 300 Each
59 NDSR G.I. Socket 20mm dia 80 Each
60 NDSR G.I. Socket 25mm dia 20 Each
61 NDSR G.I. Elbow 15mm dia 300 Each
62 NDSR G.I. Elbow 20mm dia 80 Each
63 NDSR G.I. Elbow 25mm dia 20 Each
64 NDSR G.I. Nipple 15mm dia 50 mm Long 200 Each
65 NDSR G.I. Nipple 15mm dia 75 mm Long 200 Each
66 NDSR G.I. Nipple 15mm dia 100 mm Long 200 Each
67 NDSR G.I. Nipple 15mm dia 150 mm Long 200 Each
68 NDSR G.I. Nipple 15mm dia 225 mm Long 200 Each
69 NDSR G.I. Nipple 15mm dia 300 mm Long 200 Each
70 NDSR G.I. Nipple 20mm dia 50 mm Long 50 Each
71 NDSR G.I. Nipple 20mm dia 75 mm Long 50 Each
72 NDSR G.I. Nipple 20mm dia 100 mm Long 50 Each
73 NDSR G.I. Nipple 20mm dia 150 mm Long 50 Each
74 NDSR G.I. Nipple 20mm dia 225 mm Long 50 Each
75 NDSR G.I. Nipple 20mm dia 300 mm Long 50 Each
76 2634 Aluminium sheet (0.8mm thick) 10 Kg
77 NDSR PVC Tank Cover(Syntex) 80 Each
78 7029 Galvanised wire mesh of average width of aperture
1.4 mm and nominal dia. Of wire 0.63 mm/sq.
100 Sq.ft
79 1687 Unplasticised PVC Connection pipe with brass union
30 cm long300 Each
83 1689 Unplasticised PVC Connection pipe with brass union
45 cm long300 Each
84 NDSR Nahani trap 40 Each
85 NDSR Nahani trap with hole for pipe 30 Each
86 NDSR MS clamp 2"X1/2" 50 Each
87 NDSR MS clamp 2"X3/4" 50 Each
88 NDSR GI Tee 1/2"X1/2" 80 Each
89 NDSR GI Tee 3/4"X1/2" 80 Each
90 NDSR GI Tee 3/4"X3/4" 20 Each
91 NDSR GI Tee 1"X1/2" 20 Each
92 NDSR GI Tee 1"X3/4" 20 Each
93 NDSR GI Tee 1"X1" 20 Each
94 7131 Square shape 450X450mm precast RCC manhole
cover with frame20 Each
95 7900 Bricks (Modular common burnt clay of class 7.5)3000
Per 1000
Nos
96 7379 White vitreous china clay half stall urinal flat back
580X380X350mm or angle back 450X375X350 mm
with waste fittings as per IS : 2556
10 Each
97 8207 APP modified 2mm thick membrane reinforced with
glass fibre matt50 Each
98 NDSR Brass Spindle(Piller Cock) 110 Each
99 NDSR Face inner of Bib cock 50 Each
100 NDSR M-Seal(Adhesive) 8 Each
101 7059 Aluminium hanging floor door stopper with twin
rubber & stopper 30 Each
102 666 MS Tower bolt 150mm 30 Each
103 NDSR MS Tower bolt 200mm 30 Each
104 NDSR MS Tower bolt 250mm 30 Each
105 NDSR MS Kundi (of MS aldrop) 30 Each
106 NDSR MS Aldrop 250mm 10 Each
107 NDSR Wooden Beading 20 Rmt
108 NDSR Water proofing material (Dr. Fixit) 5 Each
109 NDSR P-Trap 10 Each
110 NDSR Welder (Machine+Helper) 20 Job
111 NDSR Glass panes 4mm with putty complete 50 Sqm
112 662 MS Door Latch 300mm 20 Each
113 NDSR CPVC union 25mm 20 Each
114 NDSR MS nut bolt 20 Each Set
115 NDSR Gland Dori (For 6" valve) 10 Mtr
116 NDSR CPVC Solvent 30ml 10 Each
117 NDSR CPVC Elbow 15mm 30 Each
118 NDSR CPVC Elbow 20 mm 30 Each
119 NDSR CPVC Brass Elbow 20X15 mm 40 Each
120 NDSR Brass Elbow 20 mm 40 Each
121 NDSR CPVC Socket 20 mm 20 Each
122 NDSR CPVC Socket 25mm 10 Each
123 NDSR CPVC Tee 20 mm 10 Each
124 NDSR CPVC Nipple 20 mm 20 Each
125 NDSR CPVC Reducer 15X20mm 20 Each
126 NDSR CPVC Reducer 15X50mm 20 Each
127 NDSR CPVC Reducer 15X25mm 20 Each
128 NDSR CPVC Reducer 20X30mm 20 Each
129 8636 CPVC Pipe 15mm 50 Mtr
130 8637 CPVC Pipe 20mm 20 Mtr
131 NDSR Nail of mixed sizes 5 Kg
132 NDSR Liquid Soap Container steel 10 Each
133 NDSR Brass handle valve 15mm 80 Each
134 1019 MS Eyes & Hooks 30 Each
135 NDSR Non - Return Valve 20mm 2 Each
136 7491 Waste coupling 32mm 20 Each
137 NDSR Jet Spray(for WC) 20 Each
TotalOffice Building Maintenance(Regional Office)
CP Fitting (High Quality Fittings only as per direction of Engineer-in-charge)
138 NDSR CP Bib cock(Zim, Jaguar etc.) 10 Each
139 NDSR CP Pillar cock(Zim, Jagaur etc.) 10 Each
140 NDSR Angle Valve(Zim, Jaguar etc) 10 Each
141 NDSR Tower Bolt 300mm 5 Each
142 NDSR Large Flat back Urinal (Parryware, Cera etc.) 3 Each
143NDSR Health Faucet Telephone Type (Jaguar, Zim etc.)
4 Each
144 NDSR WC Indian Type(Parryware, Cera etc.) 2 Each
145 NDSR WC European Type(Parryware, Cera etc.) 1 Each
146 NDSR Soap Dispenser 5 Each
147 NDSR Bootle Trap 2 Each
148NDSR Handle Door for Office Building & Toilets (Door set)
3 Each
149 NDSR Push Flush System Cartridge/ Fittings 2 Each
S.No DSR No. PARTICULAR OF ITEMS QTY RATE UNIT AMOUNT
1 11011.5 sq. mm ISI Marked FR pvc insulated, single core
copper conductor cable3000 Per meter
2 11022.5 sq. mm ISI Marked FR pvc insulated, single core
copper conductor cable2500 Per meter
3 11034.0 sq. mm ISI Marked FR pvc insulated, single core
copper conductor cable1000 Per meter
4 11046.0 sq. mm ISI Marked FR pvc insulated, single core
copper conductor cable500 Per meter
5 110510 sq. mm ISI Marked FR pvc insulated, single core
copper conductor cable200 Per meter
6 110616 sq. mm ISI Marked FR pvc insulated, single core
copper conductor cable400 Per meter
7 1401 Ceiling Rose, 3pin, 5 amps ISI marked 50 Each
8 1431S.P. 5/6 amps, one way switch, piano type ISI Marked
450 Each
9 1432S.P. 5/6 amps, two way switch, piano type ISI Marked
20 Each
10 1433S.P. 15/16 amps, one way switch, piano type ISI
Marked200 Each
11 14343 pin 5/6 amps socket outlet, piano type ISI marked
100 Each
12 14356 pin 15/16 and 5/6 amps socket outlet, piano type
ISI marked50 Each
13 1436 Bell Push, piano type 20 Each
14 1437 Telephone Socket outlet piano type 20 Each
15 1402S.P. 5/6 amps, one way modular switch, ISI marked
make Legrand50 Each
16 1403S.P. 5/6 amps, two way modular switch, ISI marked
make Legrand5 Each
Total
Grand Total Part- C
Total Part- C
PART-D(i) SUPPLY OF ELECTRICAL ITEMS
17 1404S.P. 15/16 amps, one way modular switch, ISI marked
make Legrand20 Each
18 14053 pin 5/6 amps, modular socket outlet, ISI marked
make Legrand20 Each
19 14066 pin 15/16 amps, modular socket outlet, ISI marked
make Legrand10 Each
20 1407 Modular bell push, ISI marked make Legrand 10 Each
21 1408Steppeed type modular fan regulator (2 module)
make20 Each
22 1409 Telephone Socket outlet modular type 10 Each
23 1444 Call bell/buzzer, single phase 10 Each
24 1610 3 pole MCCB, 100A, 16KA 2 Each
25 1611 3 pole MCCB, 125A, 16KA 2 Each
26 1612 3 pole MCCB, 150A, 16KA 2 Each
27 1613 3 pole MCCB, 200A, 16KA 2 Each
28 1614 3 pole MCCB, 200A, 25KA 1 Each
29 1615 3 pole MCCB, 250A, 25KA 2 Each
30 1616 3 pole MCCB, 250A, 35KA 1 Each
31 1617 3 pole MCCB, 315A, 35KA 2 Each
32 1618 3 pole MCCB, 400A, 35KA 2 Each
33 1619 3 pole MCCB, 500A, 35KA 1 Each
34 1620 3 pole MCCB, 630A, 50KA 1 Each
35 1621 3 pole MCCB, 800A, 50KA 1 Each
36 17066 amps to 32 amp, ratings, SP MCB, C curve, 10 KA
breaking capacity200 Each
37 17076 amps to 32 amp, ratings, SPN MCB, C curve, 10 KA
breaking capacity100 Each
38 17086 amps to 32 amp, ratings, DP MCB, C curve, 10 KA
breaking capacity20 Each
39 17096 amps to 32 amp, ratings, TP MCB, C curve, 10 KA
breaking capacity15 Each
40 17106 amps to 32 amp, ratings, TPN MCB, C curve, 10 KA
breaking capacity10 Each
41 1711 Single pole, blanking plate 5 Each
42 1712 40 amps. 2 pole isolator 5 Each
43 1713 63 amps, 2 pole isolator 5 Each
44 1714 40 amps, 4 pole isolator 10 Each
45 1715 63 amps, 4 pole isolator 10 Each
46 1716 100 amps, 4 pole isolator 5 Each
47 1717 25 amps. Rating, 2 pole RCCB, 100 mA/300mA 5 Each
48 1718 40 amps. Rating, 2 pole RCCB, 100 mA/300mA 2 Each
49 1719 63 amps. Rating, 2 pole RCCB, 100 mA/300mA 2 Each
50 1720 25 amps. Rating, 4 pole RCCB, 100 mA/300mA 2 Each
51 1721 40 amps. Rating, 4 pole RCCB, 100 mA/300mA 2 Each
52 1722 63 amps. Rating, 4 pole RCCB, 100 mA/300mA 2 Each
53 1730
20 amps, SPN Industrial type socket outlet with plug
top and metal chained cover in sheet steel 5 Each
54 1731
20 amps, TPN Industrial type socket outlet with plug
top and metal chained cover in sheet steel 5 Each
55 1732
40 amps, TPN Industrial type socket outlet with plug
top and metal chained cover in sheet steel 5 Each
56 17544 way(4+12), TPN MCB DB, double door, horizontal
type5 Each
57 2201 Aluminium lugs for 6sqmm cable 10 Each
58 2202 Aluminium lugs for 10sqmm cable 10 Each
59 2203 Aluminium lugs for 16sqmm cable 10 Each
60 2204 Aluminium lugs for 25sqmm cable 10 Each
61 2205 Aluminium lugs for 35sqmm cable 10 Each
62 2206 Aluminium lugs for 50sqmm cable 10 Each
63 2207 Aluminium lugs for 70sqmm cable 10 Each
64 2208 Aluminium lugs for 95sqmm cable 10 Each
65 2209 Aluminium lugs for 120sqmm cable 10 Each
66 2210 Aluminium lugs for 150sqmm cable 10 Each
67 2211 Aluminium lugs for 185sqmm cable 10 Each
68 2212 Aluminium lugs for 225sqmm cable 10 Each
69 2213 Aluminium lugs for 240sqmm cable 10 Each
70 2214 Aluminium lugs for 300sqmm cable 10 Each
71 2938 cotton waste, cleaning cloth etc. 40 per kg
72 2939 cleaning materials like soap/detergent 20 per kg
S.No DSR No. PARTICULAR OF ITEMS QTY RATE UNIT AMOUNT
1 NDSR 40 amps, 4 pole MCB 10 Each
2 NDSR 63 amps, 4 pole MCB 10 Each
3 NDSR 100 amps, 4 pole MCB 5 Each
4 NDSR Sodium vapour lamp(150 watt) HPSV 20 Each
5 NDSR Mercury Vapour Lamp (125 watt) 20 Each
6 NDSRChoke/Ballast copper wound 150 watt for sodium
Vapour lamp20 Each
7 NDSRChoke/Ballast copper wound 125 watt for Mercury
Vapour lamp20 Each
8 NDSR ignitor(70/150/250/400) 20 Each
9 NDSR Capacitor 10 & 20 MFD 20 Each
10 NDSRStreet Light with integral lamp housing and control
gear. HPSV 150 watt5 Each
11 NDSR Fan regulator(conventional) ISI marked 50 Each
12 NDSR40 watt copper choke for flourescent tubelight fitting
50 Each
13 NDSR Starter for tubelight ISI marked 50 Each
14 NDSR Tube holder ISI marked 40 Each
15 NDSR 40 watt flourescent tube ISI marked 40 Each
Total
PART-D(ii) SUPPLY OF ELECTRICAL ITEMS
Grand Total Part- D(i)
16 NDSR Bulb holder for Bulb/CFL, ISI marked 50 Each
17 NDSR Rewinding of ceilling fan/wall fan 30 Each
18 NDSR Replacement of ceilling fan bearing 50 Each
19 NDSRVoltmeter (0-500v) Analog with selector Switch
2 Each
20 NDSR Voltmeter (0-500v) Digital with selector Switch 2 Each
21 NDSR Ammeter (0-60A) Analog with selector switch 2 Each
22 NDSR Ammeter (0-60A) Digital with selector switch 2 Each
23 NDSR CFL lamp/ PL 11 watt 5 Each
24 NDSR CFL lamp/ PL 18 watt 40 Each
25 NDSR CFL PL Tube 36 watt 30 Each
26 NDSR Choke for 11 watt tube 5 Each
27 NDSR Choke for 18 watt tube 40 Each
28 NDSR Choke for 36 watt tube 30 Each
29 NDSR Plug Top 5A ISI marked 10 Each
30 NDSR Plug Top 15A ISI marked 10 Each
31 NDSR Insulation tape 50 Each
32 NDSR Screw 1.5"/ any size 10 per packet
33 NDSR Gitti PVC/ Wooden 10 per packet
34 NDSR LED Indicator for panel. 24V/230v. 15 per set
35 NDSR PVC Pipe 1" 100 Per meter
36 NDSR PVC Bend 1" 50 Each
37 NDSR Wall fan/ceilling Fan Blades(Pankhudi) 4 Per set
38 NDSR16 sq.mm 3.5 core XPLE Insulated aluminium
conductor, 1.1 kv grade armoured cable100 Per meter
39 NDSR70 sq.mm 3.5 core XPLE Insulated aluminium
conductor, 1.1 kv grade armoured cable100 Per meter
40 NDSR Fan capacitor 2.5 and 4 mfd 100 Each
41 NDSR 12V, 50 watt halogen lamp 25 Each
42 NDSR Filling of fire Extinguisher ABC Type 5kg 11 Each
43 NDSR Filling of fire Extinguisher DCP Type 5kg 5 Each
44 NDSR Filling of fire Extinguisher Water Type 9Litre 8 Each
45 NDSR Filling of fire Extinguisher CO2 Type 4.5kg 20 Each
46 NDSR Replacement of 25 HP pump bearing 4 Each
47 NDSR Glend wire of 1/2" for pumpset 50 Per meter
48 NDSR Greese/Lubricant 3 per kg
49 NDSR winding of 25 HP motor 1 Each
50 NDSR supply of 3 phaSE contactor 32 amp 2 Each
51 NDSR LED Bulb 9 w To 15w 30 Each
52 NDSRLED Tubelight Complete Philips\Crompton\Bajaj
50 Each
53 NDSR
Supply, Installation, Testing and Commissioning of
fire panel make-approved by engg. Inch 1 per job
54 NDSR Smoke Detector 5 Each
55 NDSR
Providing and Fixing of Exhaust fan 300mm(Havells,
Crompton Greaves, Bajaj or an other reputed make
approved by Engineer In Charge)5 Each
56 NDSR
Supply and installation of ceiling fan 48"(Havells,
Crompton Greaves, Bajaj or an other reputed make
approved by Engineer In Charge)20 Each
57 NDSR
Providing and Fixing wall fan(Havells, Crompton
Greaves, Bajaj or an other reputed make approved by
Engineer In Charge)
30 Each
58 NDSR
Providing and making steel pole collar with cemant
concrete (1 cemant :3 coarse sand: 6 stone aggregate
20mm) of specified size and shape including form
work, plastering required, curing etc. as reqd(volume
of pole/pipe not to be deducted)
30 Each
59 NDSR
pdg & fixing MS Street light junction box of
size300mmX200mmX100mm deep made from 16
SWG MS sheet with hinged cover and locking
arrangement with 2/3 nos, holes at the bottom for
cable glands, 2 nos, 203mm Aluminium Bus Strips
mounted on DMC insulators, 1no. 6 Amp SP MCB C-
curve with Din bar and 2 nos. clamps of MS strips
25mmX3mm I\c painting, earthing etc. complete as
reqd.
30 Each
60 NDSR
S.I.T.C of 36 watt road lighting luminaire with high
power LED's and unique peanutlens to ensure
uniform distribution, on existing compound light
poles including supplying and welding suitable size
class'B' M.S. Nipple on existing pole bracket I\c
dismanting existing street light fitting etc. as
reqd.(PHILIPS Modal BRP 409 LED CW 036 MR FG S1
PSU GR or any other reputed make approved by
Engineer-in-charge)
15 Each
61 NDSRsupply and fixing of add on block with 2 NO and 2NC
suitable switch existing contactor2 Each
62 NDSRLifting and lowering of submersible motor, Repairing
Submersible pump & Motor.2 Each
S.No DSR No. PARTICULAR OF ITEMS QTY RATE UNIT AMOUNT
1 11.3
Erection of metallic pole of above 4.5m upto 6.5
meter in cemant concrete 1:3:6(1 cemant : 3 coarse
sand : 6 graded stone aggregate 40mm nominal size)
foundation including excavation and refilling etc as
required length
30 Each
Total Part D(ii)
PART-D(iii) SUPPLY OF ELECTRICAL ITEMS
2 5.2
Earthing with GI Earth pipe 4.5 mtr long, 40 dia I\c
accessories and pdg. Masonary enclosure with cover
plate having locking arrengement and watering pipe
etc. with charcoal/coke and salt, as reqd.
20 Each
Grand Total Part- D
Total Part D(iii)