Sl.

No.Total Quoted Value in `

1

2

3

Construction of Storage space for the test specimens with a room for

equipments near CE deptt.

Name of works

Miscellaneous works for making of a compartment for darkroom experiments of

Nano technology centre at Academic Complex at IITG Campus

Cycle parking around lecture hall complex

Total Amount =

Rebate if any in %.............. =

Total Amount after Rebate =

Rounded off =

(Rupees ………………………………………………………………………….. Only)

Bill of Quantities

ABSTRACT OF COST

Group - C

in figure in words

Part - A : Civil Works

EARTH WORK IN EXCAVATION

1 Earth work in excavation by mechanical means (Hydraulic excavator) /

manual means in foundation trenches or drains including dressing of sides

and ramming of bottoms, for all lifts and including getting out the excavated

soil and disposal of surplus excavated soil as directed, within the campus.

(a) All kinds of soil. cum 32.00

2 Earth work in filling in Plinth with approved quality granular soil under floors,

plinth beam, etc. as per drawing and as directed including watering,

ramming, consolidating upto 90% proctor density and dressing complete.(

The rate shall be inclusive of providing soil including all lead and lifts,

payment for land compensation for obtaining earth, payment of royalty ,

taxes etc.)

cum 22.00

ANTI-TERMITE TREATMENT:

3 Providing and injecting chemical emulsion for pre-constructional anti-termite

treatment and creating a chemical barrier under & all-round the column pits,

wall trenches, basement excavation, top surface of plinth filling, junction of

wall and floor, along the external perimeter of building, expansion joints,

surroundings of pipes and conduits etc. complete. Stages shall be treated

as per CPWD specification. (Plinth area of the building at ground floor level

only shall be measured for payments).- With Chlorpyriphos/Lindane

Emulsifiable concentrate 20% with 1% concentration.

Sqm. 55.00

4 PLAIN CEMENT CONCRETE WORK:

Providing and laying in position cement concrete of specified grade

excluding the cost of centering and shuttering - All work up to plinth level : Cum.

(a) 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40

mm nominal size)Cum 5.00

Amount (`) Rate in (`)

Qnty. UnitDescription of ItemsItem

No.

Bill of Quantities

(1) Name of Work: Construction of storage space for test specimens with a room for equipments near Civil Engineering deptt.

(b) 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20

mm nominal size).Cum 3.75

CENTERING AND SHUTTERING:

5 Centering and shuttering including strutting, propping etc. & removal of form

at all heights and levels.

(a) In foundations, footings, bases of columns, pile caps, sides of mass

concrete etc. all works up to plinth level.Sqm. 12.00

(b) In suspended floors, roofs, including slopping roofs, landings and

balconies / projections Chajjas and cast-in-situ shelves.Sqm. 18.00

(c) In lintels, beams, girders, bressummers & cantilevers including sloping

beams etc.Sqm. 70.00

(d) In column, pillars, posts & struts of all shapes. Sqm. 44.00

REINFORCEMENT:

6 Reinforcement for RCC work including straightening, cutting, bending,

binding with iron black wire 20 gauge & placing in position complete as per

drawing.

(a) Fe500 Super Ductile/Ductile Kg. 2,500.00

REINFORCED CEMENT CONCRETE WORKS:

7 Providing and laying in position specified grade of reinforced cement

concrete, excluding the cost of centering, shuttering, finishing and

reinforcement - All work up to plinth level :

(a) 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm

nominal size)Cum 24.00

8 Providing and drilling upto 20 mm dia hole and fixing threaded MS

rods of 100 to 200 mm length of 12 mm dia with nuts & washers to

be embedded in RCC floor upto 200 mm depth with fast curing

anchoring chemical adhesive FIS V 360 S of Fisherwerke GmbH &

Co. Germany and as directed.

Each 60.00

9 BRICK WORK:

Brick work with bricks of class designation 75 in foundation & plinth in

cement mortar 1:6 (1 cement : 6 coarse sand)Cum. 8.00

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of

class designation 7.5 in superstructure above plinth level up to floor V level.

(a) Cement mortar 1:4 (1 cement :4 coarse sand) Sqm 95.00

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at

every third course of half brick masonry.Sqm 95.00

WOOD WORK:

10 Providing and fixing ISI marked flush door shutters conforming to IS : 2202

(Part I) non-decorative type, core of block board construction with frame of

1st class hard wood and well matched commercial 3 ply veneering with

vertical grains or cross bands and face veneers on both faces of shutters:

(a) 35 mm thick including ISI marked Stainless Steel butt hinges with

necessary screwsSqm 2.52

11

Extra for providing lipping with 2nd class teak wood battens 25 mm

minimum depth on all edges of flush door shutters (over all area of door

shutter to be measured).

Sqm 2.52

STEEL WORK

12 Providing and fixing pressed steel door frames confirming to IS:4351

manufactured from commercial mild steel sheet of 1.6mm thickness

including hinges jamb, lock jamb, bead and if required angle threshold of

mild steel angle of section 50 x 25mm, or base ties of 1.6mm pressed mild

steel welded or rigidly fixed together by mechanical means, adjustable lugs

with split end tail to each jamb including 4 of 4" steel butt hinges 2.5mm

thick with mortar guards, lock strike-plate and shock absorbers as specified

and applying a coat of approved steel primer after pre-treatment of the

surface as directed by Engineer-in-charge.

Profile B m 5.50

13 Providing and fixing M.S. grills of required pattern in frames of windows etc.

with M.S. flats, square or round bars etc. including priming coat with

approved steel primer all complete.

(a) Fixed to openings /wooden frames with rawl plugs screws etc Kg 320.00

ALUMINIUM DOORS AND WINDOWS

14 Providing and fixing aluminium work for doors, windows, ventilators and

partitions with extruded built up standard tubular sections/ appropriate Z

sections and other sections of approved make conforming to IS: 733 and IS:

1285, fixing with dash fasteners of required dia and size, including

necessary filling up the gaps at junctions, i.e. at top, bottom and sides with

required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be

smooth, rust free, straight, mitred and jointed mechanically wherever

required including cleat angle, Aluminium snap beading for glazing /

paneling, C.P. brass / stainless steel screws, all complete as per

architectural drawings and the directions of Engineer-in-charge. Powder

coated aluminium (minimum thickness of powder coating 50 micron)

(Glazing, paneling and dash fasteners to be paid for separately) :

(a) For fixed portion kg. 85.00

(b) For shutters of doors, windows & ventilators includingproviding and fixing

hinges/ pivots and making provision for fixing of fittings wherever required

including the cost of EPDM rubber / neoprene gasket required (Fittings shall

be paid for separately)

kg 120.00

15

Providing and fixing 12mm prelaminated three layer medium density

(exterior grade) particle board Grade-I, type-II conforming to IS:12823

bonded with phenol formaldehyde synthetic resin, of approved brand and

manufacture in panelling fixed in aluminium doors shutters with C.P. / brass

/ stainless steel screws etc. complete as per architectural drawings and the

directions of Engineer-in-Charge. Decorative lamination on both sides.

sqm 2.50

16 Providing and fixing glazing in aluminium door, window, ventilator shutters

and partitions etc. with EPDM rubber / neoprene gasket etc. complete as

per the architectural drawings and the directions of engineer-in-charge .

(Cost of aluminium snap beading shall be paid in basic item):

(a) With float glass panes of 5.50 mm thickness Sqm 19.00

17 Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone

work by providing weather silicon sealant over backer rod of approved

quality as per architectural drawings and direction of Engineer-in-charge

complete.

(a) Upto 5mm depth and 5 mm width Metre 56.00

18

Providing & fixing double action hydraulic floor spring of approved brand

and manufacturer (conforming IS:6315) for aluminium doors including cost

of cutting floors as required, embedding in floors and cover plates etc. as

per direction of Engineer-in-Charge.With stainless steel cover plate

each 2.00

19 Providing and fixing colour anodized aluminium sliding bolts anodized

(anodic coating not less than grade AC-10 as per IS:1868) with nuts,

screws etc. complete.

(a) 300 x 16mm Each 2.00

20 Providing and fixing aluminium tower bolt anodized to required colour or

shade with necessary screws etc. complete.

(a) 250 x 10mm Each 4.00

21 Providing and fixing aluminium handles anodized to required colour or

shade with necessary screws etc. complete.

(a) 125mm Each 6.00

FLOORING & SKIRTING :

22 Providing flat brick soling under floor with bricks of class designation 7.5 on

a bed of 12 mm cement mortar, including filling the joints with same mortar

1:6 (1cement : 6 coarse sand), with common burnt clay non modular bricks: Sqm. 150.00

23 52 mm thick cement concrete flooring with concrete hardener topping, under

layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4

graded stone aggregate 20 mm nominal size) and top layer 12 mm thick

cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded

stone aggregate 6 mm nominal size) by volume, hardening compound

mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications.

This includes cost of cement slurry, but excluding the cost of nosing of steps

etc. complete.

Sqm 62.00

24 Providing and fixing 1st class glazed ceramic tile of approved design of min.

thickness 5.6mm in dado in any pattern and size over 12mm thick cement

plaster 1:3 ( 1 cement : 3 coarse sand) jointed with jointing compound of

matching shade and approved manufacture complete as directed.

300mmx450mm

Sqm. 16.50

FINISHING:

25

12mm thick cement plaster on even surface of wall with cement mortar 1:4 (

1 cement : 4 coarse sand).Sqm 110.00

26

15mm thick cement plaster on rough side of masonry wall of Mix 1:4 ( 1

cement : 4 coarse sand).Sqm 130.00

27

6mm plaster to ceiling and beams in cement mortar 1:3 ( 1 cement : 3

coarse sand).Sqm 33.00

28Forming groove of uniform size in the top layer of plaster surface as per

approved pattern using wooden battens, nailed to the under layer including

removal of wooden battens, repair to the edges of panels and finishing the

groove complete as per specifications and direction of the Engineer-in-

charge :

Rm 480.00

29

20 mm thick, cement plaster finished with a floating coat of neat cement of

1:4 (1 cement: 4 coarse sand) vertical damp proof course on wall between

plinth level difference

Sqm 18.00

30 Finishing walls with Acrylic Smooth exterior paint of required shade :

(a) New work (Two or more coat applied @ 1.67 ltr/10 sqm over and

including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)Sqm 150.00

31 Painting with synthetic enamel paint of approved brand and manufacture to

give an even shade: two or more coats on wood work in all shades.

(a) Two or more coats on wood/ steel work in all shades Sqm 112.00

32

Providing and applying white cement based putty of average thickness1

mm, of approved brand and manufacturer, over the plastered wall surface to

prepare the surface even and smooth complete.

Sqm 140.00

33

Applying one coat of cement primer of approved brand and manufacture on

interior wall surface.Sqm 140.00

34 Providing & applying distemper with 1st class acrylic washable distemper of

approved brand manufacture to give an even shade (two or more coats)

including removal of undulations and sand papering the same to received

one priming coat followed by two or more coats of acrylic distemper

complete in all respect.

Sqm. 140.00

ROOFING

35

Structural steel work riveted, bolted or welded in built up sections, trusses

and framed work, including cutting, hoisting, fixing in position and applying a

priming coat of approved steel primer all complete.

Kg 630.00

36 Providing and fixing precoated galvanised iron profile sheets (size, shape

and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+

0.05 %) total coated thickness with zinc coating 120 grams per sqm as per

IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of

the sheet and polyester top coat 15-18 microns. Sheet should have

protective guard film of 25 microns minimum to avoid scratches during

transportation and should be supplied in single length upto 12 metre or as

desired by Engineerin-charge. The sheet shall be fixed using self drilling /

self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto

any pitch in horizontal/ vertical or curved surfaces, excluding the cost of

purlins, rafters and trusses and including cutting to size and shape wherever

required.

Sqm 95.00

37 Providing and fixing precoated galvanised steel sheet roofing accessories

0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 120 grams per sqm

as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both

side of the sheet and polyester top coat 15-18 microns using self drilling/

self tapping screws complete :

(a) Ridges plain (500 - 600mm) Rm 12.00

(b) Barge board (Upto 300 mm) Rm 17.00

(c) Crimp curve Sqm 12.00

FALSE CEILING

38 Providing and fixing at all height false ceiling of 6 mm thick (white) finlight

PVC foamed sheet of Finolex (or equivalent) with necessary screw of

approved quality in 200 mm interval both direction to specified frame work,

including providing and fixing of frame work made of special sections power

accordance with zinc coating 600 as per IS: 277 and consisting of angle

cleats of size 25 mm wide x 1.6 mm thick with flanges of 22 mm and 37 mm

dia x 40 mm long with 6 mm dia bolts to the angle hanger being fixed with

nut and bolts to G.I channels 45x15x0.9 mm running at the rate of 1200 mm

centre to centre to which the ceiling section 0.5 mm thick bottom wedge of

80 mm with tapered flanges of 26 mm each having clips of 10.5 mm at 450,

including providing fitting and fixing of 19 mm wide melamine polished

teakwood liping to each longitudinal directions joints all complete as per

drawing and specification and direction of the Engineering in charge.

Sqm 51.00

FOOTPATH

39 Providing and laying 60mm thick faciory made cement concrete interlocking

paver block of M -30 grade made by block making machine with strong

vibratory compaction, of approved s;ze, design & shape, laid in required

colour and pattern over and including 50mm thick compacted bed of coarse

sand, filling the joints with line sand etc. all complete as per the direction of

Engineer-in-charge.

Sqm 92.00

WATER SUPPLY

40 Providing and fixing white vitreous china laboratory sink with C.I. brackets,

C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P.

brass trap with necessary C.P. brass unions complete, including painting of

fittings and brackets, cutting and making good the wall wherever required :

(a) Size 600x450x200 mm Each 1.00

41Providing and fixing C.P. brass Sink Cock with extended swinging spout

(wall mounted) with wall flange ((Make:Model :FLR-5347ND of Jaquar or

equivalent))

Each 1.00

42Providing and fixing C.P. brass short body bib cock with flange

((Make:Model :CON-037KN of Jaquar or equivalent)) 15mm

nominal bore

Each 1.00

43 Providing and fixing P.V.C. waste pipe for sink or wash basin

including P.V.C. waste fittings complete.

(a) 32 mm dia Each 1.00

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having

thermal stability for hot & cold water supply including all CPVC plain & brass

threaded fittings This includes jointing of pipes & fittings with one step

CPVC solvent cement, trenching, refilling & testing of joints complete as per

direction of Engineer in Charge.

External Work

(a) 25 mm nominal outer dia Pipes Rm 20.00

45Providing and fixing G.I. pipes complete with G.I. fittings including

trenching and refilling etc.

(a) 50 mm dia nominal bore Rm 40.00

46 Making connection of G.I. distribution branch with G.I. main of following

sizes by providing and fixing tee, including cutting and threading the pipe

etc. complete :

(a) 50 to 80 mm nominal bore Each 1.00

47 Providing and fixing gun metal gate valve with C.I. wheel of approved quality

(screwed end) :

(a) 50 mm nominal bore Each 1.00

44

(a) 25 mm nominal bore Each 1.00

48 Providing and fixing on wall face un-plasticised-Rigid PVC sewer

pipes conforming to IS:13592 (6kg/sqcm) including jointing with

seal ring conforming to IS:5382 leaving 10mm gap for thermal

expansion single socketed pipes with all accessories as clamps,

bend, door, horn bend,shoe, cowl etc. complete as directed :

(a) 110 mm dia metre 12.00

Total Amount of Part-A = -

Part-B: Electrical Works

Point Wiring

1.0

wiring of light point/ fan point/ call bell point with 1.5 sq.mm FRLS

PVC insulated copper conductor single core cable in surface/

recessed medium class PVC conduit, with piano type switch,

phenolic laminated sheet, suitable size M.S. box and earthing the

point with 1.5 Sq. mmFRLS PVC insulated copper conductor single

core cable etc. as reuired

1.1 Group B point 18

wiring for circuit/ submain wiring along with earth wire with the

folowing sizes of FRLS PVC insulated copper conductor, single

core in surface/ recessed steel conduit as required

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire meter 60

2.0

2 X 4 sq. mm + 1 X 4 sq. mm earth wire meter 140

4 X 6 sq. mm + 2 X 6 sq. mm earth wire meter 220

3.0

Installation, testing and commissioning of pre-wired, fluorescent

fitting / compact fluorescent fitting of all types, complete with all

accessories and tube/lamp etc. directly on ceiling/ wall, including

connections with 1.5 sq. mm FRLS PVC insulated, copper

conductor, single core cable and earthing etc. as required

Nos 4

Installation of exhaust fan in the existing opening, including making

good the damage, connection, testing, commissioning etc. as

required

Upto 450 mm sweep nos 2

5.0Supply and installation of following Switches and sockets of

approved make

a) 6A, piano type switch Nos. 4

b) 16A, piano type switch Nos. 10

c) 6A, 5 pin piano socket Nos. 6

2.0

4.0

d) 16A, 6 pin piano socket Nos. 10

f) modular type fan regulator Nos. 2

9.0

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C”

curve, miniature circuit breaker suitable for inductive load of

following poles in the existing MCB DB complete with connections,

testing and commissioning etc. as required.

Single pole Nos. 16

Triple pole Nos. 10

10.0

Supplying and fixing of following ways surface/ recess mounting,

vertical type, 415 V, TPN MCB distribution board of sheet steel,

dust protected, duly powder painted, inclusive of 200 A, tinned

copper bus bar, common neutral link, earth bar, din bar for

mounting MCBs (but without MCBs and incomer) as required. (Note

: Vertical type MCB TPDB is normally used where 3 phase outlets

are required.)

12 way (4 + 36), Double door Nos. 1

11.0

Providing and fixing following rating and breaking capacity and pole

MCCB with thermomagnetic release and terminal spreaders in

existing cubicle panel board including drilling holes in cubicle panel,

making connections, etc. as required.

100 A, 16 kA,TPMCCB Nos. 1

12.0Supplying and fixing TP sheet steel enclosure on surface/ recess

along with 16/25/32 A, 415 V “C” curve TP MCB complete with

connections, testing and commissioning etc. as required.

Nos. 10

supplying and fixing metal box of following sizes (nominal size) on

surface or recess with suitable size of phenolic laminated sheet

cover in front including painting etc. as required

100 mm X 100mm X60 mm deep Nos. 4

180 mm X 100mm X60 mm deep Nos. 2

200mm X 150mmX60 mm deep Nos. 10

Earthing

14.0

a) Earthing with G.I. earth pipe 4.5m long x 40mm dia including

accessories and providing masonry enclosure with cover plate

having locking arrangement and watering pipe etc. complete with

salt and charcoal as required.

Set 1

d)Supplying and laying 25mm x 5mm G.I. strip at 0.50m below

ground level as strip earth electrode including soldering etc. as

required.

meter 50

13.0

e) Providing and fixing 25mm x 5mm G.I. strip in 40mm dia G.I.

pipe from earth electrode as required.meter 10

15.0

Installation, testing and commissioning of ceiling fan, including

wiring the down rods of standard length (upto 30 cm) with 1.5 sq.

mm FRLS PVC insulated, copper conductor,single core cable etc.

as required

Nos 4

16.0

Installation, testing and commissioning of wall bracket /ceiling

fittings of all sizes and shapes containing upto two GLS/CFL/ LED

lamps per fitting,complete with all accessories including

connections etc. as required.

Nos 12

17.0

Providing, laying and fixing following dia G.I. pipe (medium class) in

ground complete with G.I. fittings including trenching (75 cm deep)

and re-filling etc. as required

50 mm dia meter 18

18.0Supply of five star rated 1200mm sweep ceiling fan ( Make

havells/CG/Orient/Berilia)No. 4

19.0

Supply of 1.1KV grade PVC/XLPE insulated Armoured Aluminum

underground Cables.(Approved Make-Havells, KEI, Polycab, RR

Kabel,RPG, NICCO, Finolex, CCI, Incab)

b). 35 Sq.mm 3 1/2 Core Mtr 50

20.0Supply of Recess mounting 20Watt LED pannel Light.(Make-Siska

(SSK-PA2708E or equivalent) Jaquar/Bajaj/Philips/CG/Havells)each 10

21.0 Supply of 40 Watt LED Street Light (Make Siska SSK-SLF-Cf-40W

or equivalent

each 2

Total Amount of Part-B =

Net Total Amount of Part (A+B) =

In figure In WordsAmount (`)

Item

No.Description of items Unit Qty.

Rate in (`)

Bill of Quantities

(2) Name of work: Miscellaneous works for making of a compartment for darkroom experiments of nanotechnology center at Academic

Complex, IITG Campus.

Providing and fixing aluminium work for doors, windows, ventilators

and partitions with extruded built up standard tubular sections/

appropriate Z sections and other sections of approved make

conforming to IS: 733 and IS: 1285, fixing with dash fasteners of

required dia and size, including necessary filling up the gaps at

junctions, i.e. at top, bottom and sides with required EPDM rubber/

neoprene gasket etc. Aluminium sections shall be smooth, rust

free, straight, mitred and jointed mechanically wherever required

including cleat angle, Aluminium snap beading for glazing /

paneling, C.P. brass / stainless steel screws, all complete as per

architectural drawings and the directions of Engineer-in-charge.

(Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion Anodised aluminium (anodised transparent or

dyed to required shade according to IS: 1868, Minimum anodic

coating of grade AC 15)

Kg 300.00

2

For shutters of doors, windows & ventilators including providing and

fixing hinges/ pivots and making provision for fixing of fittings

wherever required including the cost of EPDM rubber / neoprene

gasket required (Fittings shall be paid for separately).

Anodised aluminium (anodised transparent

or dyed to required shade according to IS:

1868, Minimum anodic coating of grade AC 15)

Kg 25.00

3

Providing and fixing 12 mm thick prelaminated particle board flat

pressed three layer or graded wood particle board conforming to IS:

12823 Grade l Type ll, in panelling fixed in aluminum doors,

windows shutters and partition frames with C.P. brass / stainless

steel screws etc. complete as per rchitectural drawings and

directions of Engineer-in-charge.Pre-laminated particle board with

decorative lamination on both sides

Sqm 12.00

4

Providing and fixing glazing in aluminium door, window, ventilator

shutters and partitions etc. with EPDM rubber / neoprene gasket

etc. complete as per the architectural drawings and the directions of

Engineer-in-charge . (Cost of aluminium snap beading shall be paid

in basic item): With float glass panes of 5.50 mm thickness

Sqm 22.00

1

5Providing and fixing of curtain cloth as per approved sample

including stitching charges.Rm 55.00

6Providing and fixing sunflim as per the direction of the Engineer in

chargeSqm 35.00

7

Providing and fixing of curtain rods of 1.25 mm thick chromium

plated brass plate, with two chroumium plated brass brackets fixed

with C.P brass screws and wooden plugs etc. whereever necessary

complete 25mm dia.

Rm 9.00

Total Amount =

In figure In WordsAmount (`)

Bill of Quantities

(3) Name of work: Cycle parking around lecture hall complex

Item

No.Description of items Unit Qty.

Rate in (`)

1

Surface dressing of the ground including removing vegetation and

inequalities not exceeding 15 cm deep and disposal of rubbish,

lead up to 50 m and lift up to 1.5 m.

Sqm 800.00

2

Providing and laying in position cement concrete of specified grade

excluding the cost of centering and shuttering - All work up to plinth

level :

(a) 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone

aggregate 20 mm nominal size).Cum 80.00

3Centering and shuttering including strutting, propping etc. and

removal of form work for :

(a) Foundations, footings, bases for columns Sqm 35.00

Total Amount =

- -

0.00

-

-